arm64: dts: khadas-vim3: add commented support for PCIe

The VIM3 on-board  MCU can mux the PCIe/USB3.0 shared differential
lines using a FUSB340TMX USB 3.1 SuperSpeed Data Switch between
an USB3.0 Type A connector and a M.2 Key M slot.
The PHY driving these differential lines is shared between
the USB3.0 controller and the PCIe Controller, thus only
a single controller can use it.

The needed DT configuration when the MCU is configured to mux
the PCIe/USB3.0 differential lines to the M.2 Key M slot is
added commented and may be uncommented to disable USB3.0 from the
USB Complex and enable the PCIe controller.

The End User is not expected to uncomment the following except for
testing purposes, but instead rely on the firmware/bootloader to
update these nodes accordingly if PCIe mode is selected by the MCU.

Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Andrew Murray <andrew.murray@arm.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>

diff --git a/arch/arm64/boot/dts/amlogic/meson-g12b-a311d-khadas-vim3.dts b/arch/arm64/boot/dts/amlogic/meson-g12b-a311d-khadas-vim3.dts
index 3a6a1e0c1e32c5cd4101e25bc979ac6ff091cdbc..124a809010840f31ff5b72dd92d9ceb82a105610 100644 (file)
--- a/arch/arm64/boot/dts/amlogic/meson-g12b-a311d-khadas-vim3.dts
+++ b/arch/arm64/boot/dts/amlogic/meson-g12b-a311d-khadas-vim3.dts
@@ -14,3 +14,28 @@
 / {
        compatible = "khadas,vim3", "amlogic,a311d", "amlogic,g12b";
 };
+
+/*
+ * The VIM3 on-board  MCU can mux the PCIe/USB3.0 shared differential
+ * lines using a FUSB340TMX USB 3.1 SuperSpeed Data Switch between
+ * an USB3.0 Type A connector and a M.2 Key M slot.
+ * The PHY driving these differential lines is shared between
+ * the USB3.0 controller and the PCIe Controller, thus only
+ * a single controller can use it.
+ * If the MCU is configured to mux the PCIe/USB3.0 differential lines
+ * to the M.2 Key M slot, uncomment the following block to disable
+ * USB3.0 from the USB Complex and enable the PCIe controller.
+ * The End User is not expected to uncomment the following except for
+ * testing purposes, but instead rely on the firmware/bootloader to
+ * update these nodes accordingly if PCIe mode is selected by the MCU.
+ */
+/*
+&pcie {
+       status = "okay";
+};
+
+&usb {
+       phys = <&usb2_phy0>, <&usb2_phy1>;
+       phy-names = "usb2-phy0", "usb2-phy1";
+};
+ */

diff --git a/arch/arm64/boot/dts/amlogic/meson-g12b-s922x-khadas-vim3.dts b/arch/arm64/boot/dts/amlogic/meson-g12b-s922x-khadas-vim3.dts
index b73deb28212059b414473ee021d89834fdedeabc..bba98f982ad6390055e823efe7ce21f7000e7e7f 100644 (file)
--- a/arch/arm64/boot/dts/amlogic/meson-g12b-s922x-khadas-vim3.dts
+++ b/arch/arm64/boot/dts/amlogic/meson-g12b-s922x-khadas-vim3.dts
@@ -14,3 +14,28 @@
 / {
        compatible = "khadas,vim3", "amlogic,s922x", "amlogic,g12b";
 };
+
+/*
+ * The VIM3 on-board  MCU can mux the PCIe/USB3.0 shared differential
+ * lines using a FUSB340TMX USB 3.1 SuperSpeed Data Switch between
+ * an USB3.0 Type A connector and a M.2 Key M slot.
+ * The PHY driving these differential lines is shared between
+ * the USB3.0 controller and the PCIe Controller, thus only
+ * a single controller can use it.
+ * If the MCU is configured to mux the PCIe/USB3.0 differential lines
+ * to the M.2 Key M slot, uncomment the following block to disable
+ * USB3.0 from the USB Complex and enable the PCIe controller.
+ * The End User is not expected to uncomment the following except for
+ * testing purposes, but instead rely on the firmware/bootloader to
+ * update these nodes accordingly if PCIe mode is selected by the MCU.
+ */
+/*
+&pcie {
+       status = "okay";
+};
+
+&usb {
+       phys = <&usb2_phy0>, <&usb2_phy1>;
+       phy-names = "usb2-phy0", "usb2-phy1";
+};
+ */

diff --git a/arch/arm64/boot/dts/amlogic/meson-khadas-vim3.dtsi b/arch/arm64/boot/dts/amlogic/meson-khadas-vim3.dtsi
index 4fe7d33ebe8a34001f04368dff5d9e2d9734646b..90815fa25ec645486e2f05654e00ffa5595c9f74 100644 (file)
--- a/arch/arm64/boot/dts/amlogic/meson-khadas-vim3.dtsi
+++ b/arch/arm64/boot/dts/amlogic/meson-khadas-vim3.dtsi
@@ -246,6 +246,10 @@
        linux,rc-map-name = "rc-khadas";
 };
 
+&pcie {
+       reset-gpios = <&gpio GPIOA_8 GPIO_ACTIVE_LOW>;
+};
+
 &pwm_ef {
         status = "okay";
         pinctrl-0 = <&pwm_e_pins>;

diff --git a/arch/arm64/boot/dts/amlogic/meson-sm1-khadas-vim3l.dts b/arch/arm64/boot/dts/amlogic/meson-sm1-khadas-vim3l.dts
index 5233bd7cacfb2394fba21ee168d12657f2cddb46..dbbf29a0dbf6d99c008b8f4851e4b27af4b7f513 100644 (file)
--- a/arch/arm64/boot/dts/amlogic/meson-sm1-khadas-vim3l.dts
+++ b/arch/arm64/boot/dts/amlogic/meson-sm1-khadas-vim3l.dts
@@ -68,3 +68,28 @@
        clock-names = "clkin1";
        status = "okay";
 };
+
+/*
+ * The VIM3 on-board  MCU can mux the PCIe/USB3.0 shared differential
+ * lines using a FUSB340TMX USB 3.1 SuperSpeed Data Switch between
+ * an USB3.0 Type A connector and a M.2 Key M slot.
+ * The PHY driving these differential lines is shared between
+ * the USB3.0 controller and the PCIe Controller, thus only
+ * a single controller can use it.
+ * If the MCU is configured to mux the PCIe/USB3.0 differential lines
+ * to the M.2 Key M slot, uncomment the following block to disable
+ * USB3.0 from the USB Complex and enable the PCIe controller.
+ * The End User is not expected to uncomment the following except for
+ * testing purposes, but instead rely on the firmware/bootloader to
+ * update these nodes accordingly if PCIe mode is selected by the MCU.
+ */
+/*
+&pcie {
+       status = "okay";
+};
+
+&usb {
+       phys = <&usb2_phy0>, <&usb2_phy1>;
+       phy-names = "usb2-phy0", "usb2-phy1";
+};
+ */