--- /dev/null
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/pinctrl/mediatek,mt8195-pinctrl.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Mediatek MT8195 Pin Controller
+
+maintainers:
+ - Sean Wang <sean.wang@mediatek.com>
+
+description: |
+ The Mediatek's Pin controller is used to control SoC pins.
+
+properties:
+ compatible:
+ const: mediatek,mt8195-pinctrl
+
+ gpio-controller: true
+
+ '#gpio-cells':
+ description: |
+ Number of cells in GPIO specifier. Since the generic GPIO binding is used,
+ the amount of cells must be specified as 2. See the below
+ mentioned gpio binding representation for description of particular cells.
+ const: 2
+
+ gpio-ranges:
+ description: gpio valid number range.
+ maxItems: 1
+
+ gpio-line-names: true
+
+ reg:
+ description: |
+ Physical address base for gpio base registers. There are 8 GPIO
+ physical address base in mt8195.
+ maxItems: 8
+
+ reg-names:
+ description: |
+ Gpio base register names.
+ maxItems: 8
+
+ interrupt-controller: true
+
+ '#interrupt-cells':
+ const: 2
+
+ interrupts:
+ description: The interrupt outputs to sysirq.
+ maxItems: 1
+
+ mediatek,rsel-resistance-in-si-unit:
+ type: boolean
+ description: |
+ Identifying i2c pins pull up/down type which is RSEL. It can support
+ RSEL define or si unit value(ohm) to set different resistance.
+
+# PIN CONFIGURATION NODES
+patternProperties:
+ '-pins$':
+ type: object
+ additionalProperties: false
+ patternProperties:
+ '^pins':
+ type: object
+ additionalProperties: false
+ description: |
+ A pinctrl node should contain at least one subnodes representing the
+ pinctrl groups available on the machine. Each subnode will list the
+ pins it needs, and how they should be configured, with regard to muxer
+ configuration, pullups, drive strength, input enable/disable and
+ input schmitt.
+ An example of using macro:
+ pincontroller {
+ /* GPIO0 set as multifunction GPIO0 */
+ gpio-pins {
+ pins {
+ pinmux = <PINMUX_GPIO0__FUNC_GPIO0>;
+ }
+ };
+ /* GPIO8 set as multifunction SDA0 */
+ i2c0-pins {
+ pins {
+ pinmux = <PINMUX_GPIO8__FUNC_SDA0>;
+ }
+ };
+ };
+ $ref: "pinmux-node.yaml"
+
+ properties:
+ pinmux:
+ description: |
+ Integer array, represents gpio pin number and mux setting.
+ Supported pin number and mux varies for different SoCs, and are
+ defined as macros in dt-bindings/pinctrl/<soc>-pinfunc.h
+ directly.
+
+ drive-strength:
+ enum: [2, 4, 6, 8, 10, 12, 14, 16]
+
+ drive-strength-microamp:
+ enum: [125, 250, 500, 1000]
+
+ bias-pull-down:
+ oneOf:
+ - type: boolean
+ - enum: [100, 101, 102, 103]
+ description: mt8195 pull down PUPD/R0/R1 type define value.
+ - enum: [200, 201, 202, 203, 204, 205, 206, 207]
+ description: mt8195 pull down RSEL type define value.
+ - enum: [75000, 5000]
+ description: mt8195 pull down RSEL type si unit value(ohm).
+ description: |
+ For pull down type is normal, it don't need add RSEL & R1R0 define
+ and resistance value.
+ For pull down type is PUPD/R0/R1 type, it can add R1R0 define to
+ set different resistance. It can support "MTK_PUPD_SET_R1R0_00" &
+ "MTK_PUPD_SET_R1R0_01" & "MTK_PUPD_SET_R1R0_10" &
+ "MTK_PUPD_SET_R1R0_11" define in mt8195.
+ For pull down type is RSEL, it can add RSEL define & resistance
+ value(ohm) to set different resistance by identifying property
+ "mediatek,rsel-resistance-in-si-unit".
+ It can support "MTK_PULL_SET_RSEL_000" & "MTK_PULL_SET_RSEL_001"
+ & "MTK_PULL_SET_RSEL_010" & "MTK_PULL_SET_RSEL_011"
+ & "MTK_PULL_SET_RSEL_100" & "MTK_PULL_SET_RSEL_101"
+ & "MTK_PULL_SET_RSEL_110" & "MTK_PULL_SET_RSEL_111"
+ define in mt8195. It can also support resistance value(ohm)
+ "75000" & "5000" in mt8195.
+
+ An example of using RSEL define:
+ pincontroller {
+ i2c0_pin {
+ pins {
+ pinmux = <PINMUX_GPIO8__FUNC_SDA0>;
+ bias-pull-down = <MTK_PULL_SET_RSEL_001>;
+ }
+ };
+ };
+ An example of using si unit resistance value(ohm):
+ &pio {
+ mediatek,rsel-resistance-in-si-unit;
+ }
+ pincontroller {
+ i2c0_pin {
+ pins {
+ pinmux = <PINMUX_GPIO8__FUNC_SDA0>;
+ bias-pull-down = <75000>;
+ }
+ };
+ };
+
+ bias-pull-up:
+ oneOf:
+ - type: boolean
+ - enum: [100, 101, 102, 103]
+ description: mt8195 pull up PUPD/R0/R1 type define value.
+ - enum: [200, 201, 202, 203, 204, 205, 206, 207]
+ description: mt8195 pull up RSEL type define value.
+ - enum: [1000, 1500, 2000, 3000, 4000, 5000, 10000, 75000]
+ description: mt8195 pull up RSEL type si unit value(ohm).
+ description: |
+ For pull up type is normal, it don't need add RSEL & R1R0 define
+ and resistance value.
+ For pull up type is PUPD/R0/R1 type, it can add R1R0 define to
+ set different resistance. It can support "MTK_PUPD_SET_R1R0_00" &
+ "MTK_PUPD_SET_R1R0_01" & "MTK_PUPD_SET_R1R0_10" &
+ "MTK_PUPD_SET_R1R0_11" define in mt8195.
+ For pull up type is RSEL, it can add RSEL define & resistance
+ value(ohm) to set different resistance by identifying property
+ "mediatek,rsel-resistance-in-si-unit".
+ It can support "MTK_PULL_SET_RSEL_000" & "MTK_PULL_SET_RSEL_001"
+ & "MTK_PULL_SET_RSEL_010" & "MTK_PULL_SET_RSEL_011"
+ & "MTK_PULL_SET_RSEL_100" & "MTK_PULL_SET_RSEL_101"
+ & "MTK_PULL_SET_RSEL_110" & "MTK_PULL_SET_RSEL_111"
+ define in mt8195. It can also support resistance value(ohm)
+ "1000" & "1500" & "2000" & "3000" & "4000" & "5000" & "10000" &
+ "75000" in mt8195.
+ An example of using RSEL define:
+ pincontroller {
+ i2c0-pins {
+ pins {
+ pinmux = <PINMUX_GPIO8__FUNC_SDA0>;
+ bias-pull-up = <MTK_PULL_SET_RSEL_001>;
+ }
+ };
+ };
+ An example of using si unit resistance value(ohm):
+ &pio {
+ mediatek,rsel-resistance-in-si-unit;
+ }
+ pincontroller {
+ i2c0-pins {
+ pins {
+ pinmux = <PINMUX_GPIO8__FUNC_SDA0>;
+ bias-pull-up = <1000>;
+ }
+ };
+ };
+
+ bias-disable: true
+
+ output-high: true
+
+ output-low: true
+
+ input-enable: true
+
+ input-disable: true
+
+ input-schmitt-enable: true
+
+ input-schmitt-disable: true
+
+ required:
+ - pinmux
+
+allOf:
+ - $ref: "pinctrl.yaml#"
+
+required:
+ - compatible
+ - reg
+ - interrupts
+ - interrupt-controller
+ - '#interrupt-cells'
+ - gpio-controller
+ - '#gpio-cells'
+ - gpio-ranges
+
+additionalProperties: false
+
+examples:
+ - |
+ #include <dt-bindings/pinctrl/mt8195-pinfunc.h>
+ #include <dt-bindings/interrupt-controller/arm-gic.h>
+ #
+ pio: pinctrl@10005000 {
+ compatible = "mediatek,mt8195-pinctrl";
+ reg = <0x10005000 0x1000>,
+ <0x11d10000 0x1000>,
+ <0x11d30000 0x1000>,
+ <0x11d40000 0x1000>,
+ <0x11e20000 0x1000>,
+ <0x11eb0000 0x1000>,
+ <0x11f40000 0x1000>,
+ <0x1000b000 0x1000>;
+ reg-names = "iocfg0", "iocfg_bm", "iocfg_bl",
+ "iocfg_br", "iocfg_lm", "iocfg_rb",
+ "iocfg_tl", "eint";
+ gpio-controller;
+ #gpio-cells = <2>;
+ gpio-ranges = <&pio 0 0 144>;
+ interrupt-controller;
+ interrupts = <GIC_SPI 225 IRQ_TYPE_LEVEL_HIGH 0>;
+ #interrupt-cells = <2>;
+
+ pio-pins {
+ pins {
+ pinmux = <PINMUX_GPIO0__FUNC_GPIO0>;
+ output-low;
+ };
+ };
+
+ spi0-pins {
+ pins-spi {
+ pinmux = <PINMUX_GPIO132__FUNC_SPIM0_CSB>,
+ <PINMUX_GPIO134__FUNC_SPIM0_MO>,
+ <PINMUX_GPIO133__FUNC_SPIM0_CLK>;
+ bias-disable;
+ };
+ pins-spi-mi {
+ pinmux = <PINMUX_GPIO135__FUNC_SPIM0_MI>;
+ bias-pull-down;
+ };
+ };
+
+ i2c0-pins {
+ pins {
+ pinmux = <PINMUX_GPIO8__FUNC_SDA0>,
+ <PINMUX_GPIO9__FUNC_SCL0>;
+ bias-disable;
+ drive-strength-microamp = <1000>;
+ };
+ };
+ };
+++ /dev/null
-# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
-%YAML 1.2
----
-$id: http://devicetree.org/schemas/pinctrl/pinctrl-mt8195.yaml#
-$schema: http://devicetree.org/meta-schemas/core.yaml#
-
-title: Mediatek MT8195 Pin Controller
-
-maintainers:
- - Sean Wang <sean.wang@mediatek.com>
-
-description: |
- The Mediatek's Pin controller is used to control SoC pins.
-
-properties:
- compatible:
- const: mediatek,mt8195-pinctrl
-
- gpio-controller: true
-
- '#gpio-cells':
- description: |
- Number of cells in GPIO specifier. Since the generic GPIO binding is used,
- the amount of cells must be specified as 2. See the below
- mentioned gpio binding representation for description of particular cells.
- const: 2
-
- gpio-ranges:
- description: gpio valid number range.
- maxItems: 1
-
- gpio-line-names: true
-
- reg:
- description: |
- Physical address base for gpio base registers. There are 8 GPIO
- physical address base in mt8195.
- maxItems: 8
-
- reg-names:
- description: |
- Gpio base register names.
- maxItems: 8
-
- interrupt-controller: true
-
- '#interrupt-cells':
- const: 2
-
- interrupts:
- description: The interrupt outputs to sysirq.
- maxItems: 1
-
- mediatek,rsel-resistance-in-si-unit:
- type: boolean
- description: |
- Identifying i2c pins pull up/down type which is RSEL. It can support
- RSEL define or si unit value(ohm) to set different resistance.
-
-# PIN CONFIGURATION NODES
-patternProperties:
- '-pins$':
- type: object
- additionalProperties: false
- patternProperties:
- '^pins':
- type: object
- additionalProperties: false
- description: |
- A pinctrl node should contain at least one subnodes representing the
- pinctrl groups available on the machine. Each subnode will list the
- pins it needs, and how they should be configured, with regard to muxer
- configuration, pullups, drive strength, input enable/disable and
- input schmitt.
- An example of using macro:
- pincontroller {
- /* GPIO0 set as multifunction GPIO0 */
- gpio-pins {
- pins {
- pinmux = <PINMUX_GPIO0__FUNC_GPIO0>;
- }
- };
- /* GPIO8 set as multifunction SDA0 */
- i2c0-pins {
- pins {
- pinmux = <PINMUX_GPIO8__FUNC_SDA0>;
- }
- };
- };
- $ref: "pinmux-node.yaml"
-
- properties:
- pinmux:
- description: |
- Integer array, represents gpio pin number and mux setting.
- Supported pin number and mux varies for different SoCs, and are
- defined as macros in dt-bindings/pinctrl/<soc>-pinfunc.h
- directly.
-
- drive-strength:
- enum: [2, 4, 6, 8, 10, 12, 14, 16]
-
- drive-strength-microamp:
- enum: [125, 250, 500, 1000]
-
- bias-pull-down:
- oneOf:
- - type: boolean
- - enum: [100, 101, 102, 103]
- description: mt8195 pull down PUPD/R0/R1 type define value.
- - enum: [200, 201, 202, 203, 204, 205, 206, 207]
- description: mt8195 pull down RSEL type define value.
- - enum: [75000, 5000]
- description: mt8195 pull down RSEL type si unit value(ohm).
- description: |
- For pull down type is normal, it don't need add RSEL & R1R0 define
- and resistance value.
- For pull down type is PUPD/R0/R1 type, it can add R1R0 define to
- set different resistance. It can support "MTK_PUPD_SET_R1R0_00" &
- "MTK_PUPD_SET_R1R0_01" & "MTK_PUPD_SET_R1R0_10" &
- "MTK_PUPD_SET_R1R0_11" define in mt8195.
- For pull down type is RSEL, it can add RSEL define & resistance
- value(ohm) to set different resistance by identifying property
- "mediatek,rsel-resistance-in-si-unit".
- It can support "MTK_PULL_SET_RSEL_000" & "MTK_PULL_SET_RSEL_001"
- & "MTK_PULL_SET_RSEL_010" & "MTK_PULL_SET_RSEL_011"
- & "MTK_PULL_SET_RSEL_100" & "MTK_PULL_SET_RSEL_101"
- & "MTK_PULL_SET_RSEL_110" & "MTK_PULL_SET_RSEL_111"
- define in mt8195. It can also support resistance value(ohm)
- "75000" & "5000" in mt8195.
-
- An example of using RSEL define:
- pincontroller {
- i2c0_pin {
- pins {
- pinmux = <PINMUX_GPIO8__FUNC_SDA0>;
- bias-pull-down = <MTK_PULL_SET_RSEL_001>;
- }
- };
- };
- An example of using si unit resistance value(ohm):
- &pio {
- mediatek,rsel-resistance-in-si-unit;
- }
- pincontroller {
- i2c0_pin {
- pins {
- pinmux = <PINMUX_GPIO8__FUNC_SDA0>;
- bias-pull-down = <75000>;
- }
- };
- };
-
- bias-pull-up:
- oneOf:
- - type: boolean
- - enum: [100, 101, 102, 103]
- description: mt8195 pull up PUPD/R0/R1 type define value.
- - enum: [200, 201, 202, 203, 204, 205, 206, 207]
- description: mt8195 pull up RSEL type define value.
- - enum: [1000, 1500, 2000, 3000, 4000, 5000, 10000, 75000]
- description: mt8195 pull up RSEL type si unit value(ohm).
- description: |
- For pull up type is normal, it don't need add RSEL & R1R0 define
- and resistance value.
- For pull up type is PUPD/R0/R1 type, it can add R1R0 define to
- set different resistance. It can support "MTK_PUPD_SET_R1R0_00" &
- "MTK_PUPD_SET_R1R0_01" & "MTK_PUPD_SET_R1R0_10" &
- "MTK_PUPD_SET_R1R0_11" define in mt8195.
- For pull up type is RSEL, it can add RSEL define & resistance
- value(ohm) to set different resistance by identifying property
- "mediatek,rsel-resistance-in-si-unit".
- It can support "MTK_PULL_SET_RSEL_000" & "MTK_PULL_SET_RSEL_001"
- & "MTK_PULL_SET_RSEL_010" & "MTK_PULL_SET_RSEL_011"
- & "MTK_PULL_SET_RSEL_100" & "MTK_PULL_SET_RSEL_101"
- & "MTK_PULL_SET_RSEL_110" & "MTK_PULL_SET_RSEL_111"
- define in mt8195. It can also support resistance value(ohm)
- "1000" & "1500" & "2000" & "3000" & "4000" & "5000" & "10000" &
- "75000" in mt8195.
- An example of using RSEL define:
- pincontroller {
- i2c0-pins {
- pins {
- pinmux = <PINMUX_GPIO8__FUNC_SDA0>;
- bias-pull-up = <MTK_PULL_SET_RSEL_001>;
- }
- };
- };
- An example of using si unit resistance value(ohm):
- &pio {
- mediatek,rsel-resistance-in-si-unit;
- }
- pincontroller {
- i2c0-pins {
- pins {
- pinmux = <PINMUX_GPIO8__FUNC_SDA0>;
- bias-pull-up = <1000>;
- }
- };
- };
-
- bias-disable: true
-
- output-high: true
-
- output-low: true
-
- input-enable: true
-
- input-disable: true
-
- input-schmitt-enable: true
-
- input-schmitt-disable: true
-
- required:
- - pinmux
-
-allOf:
- - $ref: "pinctrl.yaml#"
-
-required:
- - compatible
- - reg
- - interrupts
- - interrupt-controller
- - '#interrupt-cells'
- - gpio-controller
- - '#gpio-cells'
- - gpio-ranges
-
-additionalProperties: false
-
-examples:
- - |
- #include <dt-bindings/pinctrl/mt8195-pinfunc.h>
- #include <dt-bindings/interrupt-controller/arm-gic.h>
- #
- pio: pinctrl@10005000 {
- compatible = "mediatek,mt8195-pinctrl";
- reg = <0x10005000 0x1000>,
- <0x11d10000 0x1000>,
- <0x11d30000 0x1000>,
- <0x11d40000 0x1000>,
- <0x11e20000 0x1000>,
- <0x11eb0000 0x1000>,
- <0x11f40000 0x1000>,
- <0x1000b000 0x1000>;
- reg-names = "iocfg0", "iocfg_bm", "iocfg_bl",
- "iocfg_br", "iocfg_lm", "iocfg_rb",
- "iocfg_tl", "eint";
- gpio-controller;
- #gpio-cells = <2>;
- gpio-ranges = <&pio 0 0 144>;
- interrupt-controller;
- interrupts = <GIC_SPI 225 IRQ_TYPE_LEVEL_HIGH 0>;
- #interrupt-cells = <2>;
-
- pio-pins {
- pins {
- pinmux = <PINMUX_GPIO0__FUNC_GPIO0>;
- output-low;
- };
- };
-
- spi0-pins {
- pins-spi {
- pinmux = <PINMUX_GPIO132__FUNC_SPIM0_CSB>,
- <PINMUX_GPIO134__FUNC_SPIM0_MO>,
- <PINMUX_GPIO133__FUNC_SPIM0_CLK>;
- bias-disable;
- };
- pins-spi-mi {
- pinmux = <PINMUX_GPIO135__FUNC_SPIM0_MI>;
- bias-pull-down;
- };
- };
-
- i2c0-pins {
- pins {
- pinmux = <PINMUX_GPIO8__FUNC_SDA0>,
- <PINMUX_GPIO9__FUNC_SCL0>;
- bias-disable;
- drive-strength-microamp = <1000>;
- };
- };
- };
projects / linux.git / commitdiff