property, describing the physical location of the children nodes.
0 means motherboard site, while 1 and 2 are daughterboard sites, and
0xf means "sisterboard" which is the site containing the main CPU tile.
- allOf:
- - $ref: '/schemas/types.yaml#/definitions/uint32'
- - minimum: 0
- maximum: 15
+ $ref: '/schemas/types.yaml#/definitions/uint32'
+ minimum: 0
+ maximum: 15
arm,vexpress,position:
description: When daughterboards are stacked on one site, their position
in the stack be be described this attribute.
- allOf:
- - $ref: '/schemas/types.yaml#/definitions/uint32'
- - minimum: 0
- maximum: 3
+ $ref: '/schemas/types.yaml#/definitions/uint32'
+ minimum: 0
+ maximum: 3
arm,vexpress,dcc:
description: When describing tiles consisting of more than one DCC, its
number can be specified with this attribute.
- allOf:
- - $ref: '/schemas/types.yaml#/definitions/uint32'
- - minimum: 0
- maximum: 3
+ $ref: '/schemas/types.yaml#/definitions/uint32'
+ minimum: 0
+ maximum: 3
patternProperties:
"^bus@[0-9a-f]+$":
"simple-bus". If the compatible is placed in the "motherboard" node,
it is stricter and always has two compatibles.
type: object
- allOf:
- - $ref: '/schemas/simple-bus.yaml'
+ $ref: '/schemas/simple-bus.yaml'
properties:
compatible:
- const: simple-bus
arm,v2m-memory-map:
description: This describes the memory map type.
- allOf:
- - $ref: '/schemas/types.yaml#/definitions/string'
- - enum:
- - rs1
- - rs2
+ $ref: '/schemas/types.yaml#/definitions/string'
+ enum:
+ - rs1
+ - rs2
+
required:
- compatible
required:
maxItems: 1
arm,trig-in-sigs:
- allOf:
- - $ref: /schemas/types.yaml#/definitions/uint32-array
+ $ref: /schemas/types.yaml#/definitions/uint32-array
minItems: 1
maxItems: 32
description:
List of CTI trigger in signal numbers in use by a trig-conns node.
arm,trig-in-types:
- allOf:
- - $ref: /schemas/types.yaml#/definitions/uint32-array
+ $ref: /schemas/types.yaml#/definitions/uint32-array
minItems: 1
maxItems: 32
description:
completely, then the types will default to GEN_IO.
arm,trig-out-sigs:
- allOf:
- - $ref: /schemas/types.yaml#/definitions/uint32-array
+ $ref: /schemas/types.yaml#/definitions/uint32-array
minItems: 1
maxItems: 32
description:
List of CTI trigger out signal numbers in use by a trig-conns node.
arm,trig-out-types:
- allOf:
- - $ref: /schemas/types.yaml#/definitions/uint32-array
+ $ref: /schemas/types.yaml#/definitions/uint32-array
minItems: 1
maxItems: 32
description:
or omitted completely, then the types will default to GEN_IO.
arm,trig-filters:
- allOf:
- - $ref: /schemas/types.yaml#/definitions/uint32-array
+ $ref: /schemas/types.yaml#/definitions/uint32-array
minItems: 1
maxItems: 32
description:
active, unless filtering is disabled on the driver.
arm,trig-conn-name:
- allOf:
- - $ref: /schemas/types.yaml#/definitions/string
+ $ref: /schemas/types.yaml#/definitions/string
description:
Defines a connection name that will be displayed, if the cpu or
arm,cs-dev-assoc properties are not being used in this connection.
- qcom,scorpion
enable-method:
- allOf:
- - $ref: '/schemas/types.yaml#/definitions/string'
- - oneOf:
- # On ARM v8 64-bit this property is required
- - enum:
- - psci
- - spin-table
- # On ARM 32-bit systems this property is optional
- - enum:
- - actions,s500-smp
- - allwinner,sun6i-a31
- - allwinner,sun8i-a23
- - allwinner,sun9i-a80-smp
- - allwinner,sun8i-a83t-smp
- - amlogic,meson8-smp
- - amlogic,meson8b-smp
- - arm,realview-smp
- - aspeed,ast2600-smp
- - brcm,bcm11351-cpu-method
- - brcm,bcm23550
- - brcm,bcm2836-smp
- - brcm,bcm63138
- - brcm,bcm-nsp-smp
- - brcm,brahma-b15
- - marvell,armada-375-smp
- - marvell,armada-380-smp
- - marvell,armada-390-smp
- - marvell,armada-xp-smp
- - marvell,98dx3236-smp
- - marvell,mmp3-smp
- - mediatek,mt6589-smp
- - mediatek,mt81xx-tz-smp
- - qcom,gcc-msm8660
- - qcom,kpss-acc-v1
- - qcom,kpss-acc-v2
- - renesas,apmu
- - renesas,r9a06g032-smp
- - rockchip,rk3036-smp
- - rockchip,rk3066-smp
- - socionext,milbeaut-m10v-smp
- - ste,dbx500-smp
- - ti,am3352
- - ti,am4372
+ $ref: '/schemas/types.yaml#/definitions/string'
+ oneOf:
+ # On ARM v8 64-bit this property is required
+ - enum:
+ - psci
+ - spin-table
+ # On ARM 32-bit systems this property is optional
+ - enum:
+ - actions,s500-smp
+ - allwinner,sun6i-a31
+ - allwinner,sun8i-a23
+ - allwinner,sun9i-a80-smp
+ - allwinner,sun8i-a83t-smp
+ - amlogic,meson8-smp
+ - amlogic,meson8b-smp
+ - arm,realview-smp
+ - aspeed,ast2600-smp
+ - brcm,bcm11351-cpu-method
+ - brcm,bcm23550
+ - brcm,bcm2836-smp
+ - brcm,bcm63138
+ - brcm,bcm-nsp-smp
+ - brcm,brahma-b15
+ - marvell,armada-375-smp
+ - marvell,armada-380-smp
+ - marvell,armada-390-smp
+ - marvell,armada-xp-smp
+ - marvell,98dx3236-smp
+ - marvell,mmp3-smp
+ - mediatek,mt6589-smp
+ - mediatek,mt81xx-tz-smp
+ - qcom,gcc-msm8660
+ - qcom,kpss-acc-v1
+ - qcom,kpss-acc-v2
+ - renesas,apmu
+ - renesas,r9a06g032-smp
+ - rockchip,rk3036-smp
+ - rockchip,rk3066-smp
+ - socionext,milbeaut-m10v-smp
+ - ste,dbx500-smp
+ - ti,am3352
+ - ti,am4372
cpu-release-addr:
$ref: '/schemas/types.yaml#/definitions/uint64'
description: Cycles of latency for Data RAM accesses. Specifies 3 cells of
read, write and setup latencies. Minimum valid values are 1. Controllers
without setup latency control should use a value of 0.
- allOf:
- - $ref: /schemas/types.yaml#/definitions/uint32-array
- - minItems: 2
- maxItems: 3
- items:
- minimum: 0
- maximum: 8
+ $ref: /schemas/types.yaml#/definitions/uint32-array
+ minItems: 2
+ maxItems: 3
+ items:
+ minimum: 0
+ maximum: 8
arm,tag-latency:
description: Cycles of latency for Tag RAM accesses. Specifies 3 cells of
read, write and setup latencies. Controllers without setup latency control
should use 0. Controllers without separate read and write Tag RAM latency
values should only use the first cell.
- allOf:
- - $ref: /schemas/types.yaml#/definitions/uint32-array
- - minItems: 1
- maxItems: 3
- items:
- minimum: 0
- maximum: 8
+ $ref: /schemas/types.yaml#/definitions/uint32-array
+ minItems: 1
+ maxItems: 3
+ items:
+ minimum: 0
+ maximum: 8
arm,dirty-latency:
description: Cycles of latency for Dirty RAMs. This is a single cell.
- allOf:
- - $ref: /schemas/types.yaml#/definitions/uint32
- - minimum: 1
- maximum: 8
+ $ref: /schemas/types.yaml#/definitions/uint32
+ minimum: 1
+ maximum: 8
arm,filter-ranges:
description: <start length> Starting address and length of window to
filter. Addresses in the filter window are directed to the M1 port. Other
addresses will go to the M0 port.
- allOf:
- - $ref: /schemas/types.yaml#/definitions/uint32-array
- - items:
- minItems: 2
- maxItems: 2
+ $ref: /schemas/types.yaml#/definitions/uint32-array
+ items:
+ minItems: 2
+ maxItems: 2
arm,io-coherent:
description: indicates that the system is operating in an hardware
arm,double-linefill:
description: Override double linefill enable setting. Enable if
non-zero, disable if zero.
- allOf:
- - $ref: /schemas/types.yaml#/definitions/uint32
- - enum: [ 0, 1 ]
+ $ref: /schemas/types.yaml#/definitions/uint32
+ enum: [0, 1]
arm,double-linefill-incr:
description: Override double linefill on INCR read. Enable
if non-zero, disable if zero.
- allOf:
- - $ref: /schemas/types.yaml#/definitions/uint32
- - enum: [ 0, 1 ]
+ $ref: /schemas/types.yaml#/definitions/uint32
+ enum: [0, 1]
arm,double-linefill-wrap:
description: Override double linefill on WRAP read. Enable
if non-zero, disable if zero.
- allOf:
- - $ref: /schemas/types.yaml#/definitions/uint32
- - enum: [ 0, 1 ]
+ $ref: /schemas/types.yaml#/definitions/uint32
+ enum: [0, 1]
arm,prefetch-drop:
description: Override prefetch drop enable setting. Enable if non-zero,
disable if zero.
- allOf:
- - $ref: /schemas/types.yaml#/definitions/uint32
- - enum: [ 0, 1 ]
+ $ref: /schemas/types.yaml#/definitions/uint32
+ enum: [0, 1]
arm,prefetch-offset:
description: Override prefetch offset value.
- allOf:
- - $ref: /schemas/types.yaml#/definitions/uint32
- - enum: [ 0, 1, 2, 3, 4, 5, 6, 7, 15, 23, 31 ]
+ $ref: /schemas/types.yaml#/definitions/uint32
+ enum: [0, 1, 2, 3, 4, 5, 6, 7, 15, 23, 31]
arm,shared-override:
description: The default behavior of the L220 or PL310 cache
description: |
Data prefetch. Value: <0> (forcibly disable), <1>
(forcibly enable), property absent (retain settings set by firmware)
- allOf:
- - $ref: /schemas/types.yaml#/definitions/uint32
- - enum: [ 0, 1 ]
+ $ref: /schemas/types.yaml#/definitions/uint32
+ enum: [0, 1]
prefetch-instr:
description: |
Instruction prefetch. Value: <0> (forcibly disable),
<1> (forcibly enable), property absent (retain settings set by
firmware)
- allOf:
- - $ref: /schemas/types.yaml#/definitions/uint32
- - enum: [ 0, 1 ]
+ $ref: /schemas/types.yaml#/definitions/uint32
+ enum: [0, 1]
arm,dynamic-clock-gating:
description: |
L2 dynamic clock gating. Value: <0> (forcibly
disable), <1> (forcibly enable), property absent (OS specific behavior,
preferably retain firmware settings)
- allOf:
- - $ref: /schemas/types.yaml#/definitions/uint32
- - enum: [ 0, 1 ]
+ $ref: /schemas/types.yaml#/definitions/uint32
+ enum: [0, 1]
arm,standby-mode:
description: L2 standby mode enable. Value <0> (forcibly disable),
<1> (forcibly enable), property absent (OS specific behavior,
preferably retain firmware settings)
- allOf:
- - $ref: /schemas/types.yaml#/definitions/uint32
- - enum: [ 0, 1 ]
+ $ref: /schemas/types.yaml#/definitions/uint32
+ enum: [0, 1]
arm,early-bresp-disable:
description: Disable the CA9 optimization Early BRESP (PL310)
method:
description: The method of calling the PSCI firmware.
- allOf:
- - $ref: /schemas/types.yaml#/definitions/string-array
- - enum:
- # SMC #0, with the register assignments specified in this binding.
- - smc
- # HVC #0, with the register assignments specified in this binding.
- - hvc
+ $ref: /schemas/types.yaml#/definitions/string-array
+ enum:
+ - smc
+ # HVC #0, with the register assignments specified in this binding.
+ - hvc
cpu_suspend:
$ref: /schemas/types.yaml#/definitions/uint32
patternProperties:
"^power-domain-":
- allOf:
- - $ref: "../power/power-domain.yaml#"
+ $ref: "../power/power-domain.yaml#"
+
type: object
description: |
ARM systems can have multiple cores, sometimes in an hierarchical
Adaptive Supply Voltage bin selection. This can be used
to determine the ASV bin of an SoC if respective information
is missing in the CHIPID registers or in the OTP memory.
- allOf:
- - $ref: /schemas/types.yaml#/definitions/uint32
- - enum: [ 0, 1, 2, 3 ]
+ $ref: /schemas/types.yaml#/definitions/uint32
+ enum: [0, 1, 2, 3]
required:
- compatible
maxItems: 1
allwinner,sram:
- allOf:
- - $ref: /schemas/types.yaml#definitions/phandle-array
- - maxItems: 1
description:
The SRAM that needs to be claimed to access the display engine
bus.
+ $ref: /schemas/types.yaml#definitions/phandle-array
+ maxItems: 1
ranges: true
clock-div:
description: Fixed divider
- allOf:
- - $ref: /schemas/types.yaml#/definitions/uint32
- - minimum: 1
+ $ref: /schemas/types.yaml#/definitions/uint32
+ minimum: 1
clock-mult:
description: Fixed multiplier
description: Size of the connector, should be specified in case of
non-fullsize 'usb-a-connector' or 'usb-b-connector' compatible
connectors.
- allOf:
- - $ref: /schemas/types.yaml#definitions/string
+ $ref: /schemas/types.yaml#definitions/string
+
enum:
- mini
- micro
power-role:
description: Determines the power role that the Type C connector will
support. "dual" refers to Dual Role Port (DRP).
- allOf:
- - $ref: /schemas/types.yaml#definitions/string
+ $ref: /schemas/types.yaml#definitions/string
+
enum:
- source
- sink
try-power-role:
description: Preferred power role.
- allOf:
- - $ref: /schemas/types.yaml#definitions/string
+ $ref: /schemas/types.yaml#definitions/string
+
enum:
- - source
- - sink
- - dual
+ - source
+ - sink
+ - dual
data-role:
description: Data role if Type C connector supports USB data. "dual" refers
Dual Role Device (DRD).
- allOf:
- - $ref: /schemas/types.yaml#definitions/string
+ $ref: /schemas/types.yaml#definitions/string
+
enum:
- host
- device
defined in dt-bindings/usb/pd.h.
minItems: 1
maxItems: 7
- allOf:
- - $ref: /schemas/types.yaml#/definitions/uint32-array
+ $ref: /schemas/types.yaml#/definitions/uint32-array
sink-pdos:
description: An array of u32 with each entry providing supported power sink
in dt-bindings/usb/pd.h.
minItems: 1
maxItems: 7
- allOf:
- - $ref: /schemas/types.yaml#/definitions/uint32-array
+ $ref: /schemas/types.yaml#/definitions/uint32-array
op-sink-microwatt:
description: Sink required operating power in microwatt, if source can't
dma-maxburst:
description: Set number of maximum dma burst supported
- allOf:
- - $ref: /schemas/types.yaml#/definitions/uint32
- - minimum: 0
- - maximum: 2
- - default: 0
+ $ref: /schemas/types.yaml#/definitions/uint32
+ minimum: 0
+ maximum: 2
+ default: 0
required:
- compatible
- allwinner,sun50i-h6-display-engine
allwinner,pipelines:
- allOf:
- - $ref: /schemas/types.yaml#/definitions/phandle-array
- - minItems: 1
- maxItems: 2
+ $ref: /schemas/types.yaml#/definitions/phandle-array
+ minItems: 1
+ maxItems: 2
description: |
Available display engine frontends (DE 1.0) or mixers (DE
2.0/3.0) available.
maxItems: 4
clock-output-names:
- allOf:
- - $ref: /schemas/types.yaml#/definitions/string-array
- - maxItems: 1
description:
Name of the LCD pixel clock created.
+ $ref: /schemas/types.yaml#/definitions/string-array
+ maxItems: 1
dmas:
maxItems: 1
rotation:
description:
Display rotation in degrees counter clockwise (0,90,180,270)
- allOf:
- - $ref: /schemas/types.yaml#/definitions/uint32
- - enum: [ 0, 90, 180, 270 ]
+ $ref: /schemas/types.yaml#/definitions/uint32
+ enum: [0, 90, 180, 270]
# Display Timings
panel-timing:
Most display panels are restricted to a single resolution and
require specific display timings. The panel-timing subnode expresses those
timings.
- allOf:
- - $ref: panel-timing.yaml#
+ $ref: panel-timing.yaml#
display-timings:
description:
Some display panels supports several resolutions with different timing.
The display-timings bindings supports specifying several timings and
optional specify which is the native mode.
- allOf:
- - $ref: display-timings.yaml#
+ $ref: display-timings.yaml#
# Connectivity
port:
hfront-porch:
description: Horizontal front porch panel timing
oneOf:
- - allOf:
- - $ref: /schemas/types.yaml#/definitions/uint32
- - maxItems: 1
- items:
- description: typical number of pixels
- - allOf:
- - $ref: /schemas/types.yaml#/definitions/uint32-array
- - minItems: 3
- maxItems: 3
- items:
- description: min, typ, max number of pixels
+ - $ref: /schemas/types.yaml#/definitions/uint32
+ maxItems: 1
+ items:
+ description: typical number of pixels
+ - $ref: /schemas/types.yaml#/definitions/uint32-array
+ minItems: 3
+ maxItems: 3
+ items:
+ description: min, typ, max number of pixels
hback-porch:
description: Horizontal back porch timing
oneOf:
- - allOf:
- - $ref: /schemas/types.yaml#/definitions/uint32
- - maxItems: 1
- items:
- description: typical number of pixels
- - allOf:
- - $ref: /schemas/types.yaml#/definitions/uint32-array
- - minItems: 3
- maxItems: 3
- items:
- description: min, typ, max number of pixels
+ - $ref: /schemas/types.yaml#/definitions/uint32
+ maxItems: 1
+ items:
+ description: typical number of pixels
+ - $ref: /schemas/types.yaml#/definitions/uint32-array
+ minItems: 3
+ maxItems: 3
+ items:
+ description: min, typ, max number of pixels
hsync-len:
description: Horizontal sync length panel timing
oneOf:
- - allOf:
- - $ref: /schemas/types.yaml#/definitions/uint32
- - maxItems: 1
- items:
- description: typical number of pixels
- - allOf:
- - $ref: /schemas/types.yaml#/definitions/uint32-array
- - minItems: 3
- maxItems: 3
- items:
- description: min, typ, max number of pixels
+ - $ref: /schemas/types.yaml#/definitions/uint32
+ maxItems: 1
+ items:
+ description: typical number of pixels
+ - $ref: /schemas/types.yaml#/definitions/uint32-array
+ minItems: 3
+ maxItems: 3
+ items:
+ description: min, typ, max number of pixels
vfront-porch:
description: Vertical front porch panel timing
oneOf:
- - allOf:
- - $ref: /schemas/types.yaml#/definitions/uint32
- - maxItems: 1
- items:
- description: typical number of lines
- - allOf:
- - $ref: /schemas/types.yaml#/definitions/uint32-array
- - minItems: 3
- maxItems: 3
- items:
- description: min, typ, max number of lines
+ - $ref: /schemas/types.yaml#/definitions/uint32
+ maxItems: 1
+ items:
+ description: typical number of lines
+ - $ref: /schemas/types.yaml#/definitions/uint32-array
+ minItems: 3
+ maxItems: 3
+ items:
+ description: min, typ, max number of lines
vback-porch:
description: Vertical back porch panel timing
oneOf:
- - allOf:
- - $ref: /schemas/types.yaml#/definitions/uint32
- - maxItems: 1
- items:
- description: typical number of lines
- - allOf:
- - $ref: /schemas/types.yaml#/definitions/uint32-array
- - minItems: 3
- maxItems: 3
- items:
- description: min, typ, max number of lines
+ - $ref: /schemas/types.yaml#/definitions/uint32
+ maxItems: 1
+ items:
+ description: typical number of lines
+ - $ref: /schemas/types.yaml#/definitions/uint32-array
+ minItems: 3
+ maxItems: 3
+ items:
+ description: min, typ, max number of lines
vsync-len:
description: Vertical sync length panel timing
oneOf:
- - allOf:
- - $ref: /schemas/types.yaml#/definitions/uint32
- - maxItems: 1
- items:
- description: typical number of lines
- - allOf:
- - $ref: /schemas/types.yaml#/definitions/uint32-array
- - minItems: 3
- maxItems: 3
- items:
- description: min, typ, max number of lines
+ - $ref: /schemas/types.yaml#/definitions/uint32
+ maxItems: 1
+ items:
+ description: typical number of lines
+ - $ref: /schemas/types.yaml#/definitions/uint32-array
+ minItems: 3
+ maxItems: 3
+ items:
+ description: min, typ, max number of lines
hsync-active:
description: |
- "#size-cells"
ti,am65x-oldi-io-ctrl:
- allOf:
- - $ref: "/schemas/types.yaml#/definitions/phandle-array"
- - maxItems: 1
+ $ref: "/schemas/types.yaml#/definitions/phandle-array"
+ maxItems: 1
description:
phandle to syscon device node mapping OLDI IO_CTRL registers.
The mapped range should point to OLDI_DAT0_IO_CTRL, map it and
kernel. i.e. first channel corresponds to LSB.
The first item in the array is for channels 0-31, the second is for
channels 32-63, etc.
- allOf:
- - $ref: /schemas/types.yaml#/definitions/uint32-array
+ $ref: /schemas/types.yaml#/definitions/uint32-array
items:
minItems: 1
# Should be enough
ti,sci:
description: phandle to TI-SCI compatible System controller node
- allOf:
- - $ref: /schemas/types.yaml#/definitions/phandle
+ $ref: /schemas/types.yaml#/definitions/phandle
ti,sci-dev-id:
description: TI-SCI device id of UDMAP
- allOf:
- - $ref: /schemas/types.yaml#/definitions/uint32
+ $ref: /schemas/types.yaml#/definitions/uint32
ti,ringacc:
description: phandle to the ring accelerator node
- allOf:
- - $ref: /schemas/types.yaml#/definitions/phandle
+ $ref: /schemas/types.yaml#/definitions/phandle
ti,sci-rm-range-tchan:
description: |
Array of UDMA tchan resource subtypes for resource allocation for this
host
- allOf:
- - $ref: /schemas/types.yaml#/definitions/uint32-array
+ $ref: /schemas/types.yaml#/definitions/uint32-array
minItems: 1
# Should be enough
maxItems: 255
description: |
Array of UDMA rchan resource subtypes for resource allocation for this
host
- allOf:
- - $ref: /schemas/types.yaml#/definitions/uint32-array
+ $ref: /schemas/types.yaml#/definitions/uint32-array
minItems: 1
# Should be enough
maxItems: 255
description: |
Array of UDMA rflow resource subtypes for resource allocation for this
host
- allOf:
- - $ref: /schemas/types.yaml#/definitions/uint32-array
+ $ref: /schemas/types.yaml#/definitions/uint32-array
minItems: 1
# Should be enough
maxItems: 255
properties:
ti,udma-atype:
description: ATYPE value which should be used by non slave channels
- allOf:
- - $ref: /schemas/types.yaml#/definitions/uint32
+ $ref: /schemas/types.yaml#/definitions/uint32
required:
- ti,udma-atype
maxItems: 1
pagesize:
- allOf:
- - $ref: /schemas/types.yaml#/definitions/uint32
description:
The length of the pagesize for writing. Please consult the
manual of your device, that value varies a lot. A wrong value
may result in data loss! If not specified, a safety value of
'1' is used which will be very slow.
- enum: [ 1, 8, 16, 32, 64, 128, 258 ]
+ $ref: /schemas/types.yaml#/definitions/uint32
+ enum: [1, 8, 16, 32, 64, 128, 258]
default: 1
read-only:
wp-gpios: true
address-width:
- allOf:
- - $ref: /schemas/types.yaml#/definitions/uint32
description:
Number of address bits.
+ $ref: /schemas/types.yaml#/definitions/uint32
default: 8
enum: [ 8, 16 ]
num-addresses:
- allOf:
- - $ref: /schemas/types.yaml#/definitions/uint32
description:
Total number of i2c slave addresses this device takes.
+ $ref: /schemas/types.yaml#/definitions/uint32
default: 1
minimum: 1
maximum: 8
# 'description'.
vendor,int-property:
description: Vendor specific properties must have a description
- # 'allOf' is the json-schema way of subclassing a schema. Here the base
- # type schema is referenced and then additional constraints on the values
- # are added.
- allOf:
- - $ref: /schemas/types.yaml#/definitions/uint32
- - enum: [2, 4, 6, 8, 10]
+ $ref: /schemas/types.yaml#/definitions/uint32
+ enum: [2, 4, 6, 8, 10]
vendor,bool-property:
description: Vendor specific properties must have a description. Boolean
vendor,string-array-property:
description: Vendor specific properties should reference a type in the
core schema.
- allOf:
- - $ref: /schemas/types.yaml#/definitions/string-array
- - items:
- - enum: [ foo, bar ]
- - enum: [ baz, boo ]
+ $ref: /schemas/types.yaml#/definitions/string-array
+ items:
+ - enum: [foo, bar]
+ - enum: [baz, boo]
vendor,property-in-standard-units-microvolt:
description: Vendor specific properties having a standard unit suffix
const: google,extcon-usbc-cros-ec
google,usb-port-id:
- allOf:
- - $ref: /schemas/types.yaml#/definitions/uint32
+ $ref: /schemas/types.yaml#/definitions/uint32
description: the port id
minimum: 0
maximum: 255
description:
Value specifying the number of pulses per revolution of the controlled
FAN.
- allOf:
- - $ref: /schemas/types.yaml#/definitions/uint32
+ $ref: /schemas/types.yaml#/definitions/uint32
enum: [1, 2, 4]
required:
the accumulated values, this entry can also have two items which sets
energy1/charge1 and energy2/charger2 respectively. Check table 12 of the
datasheet for more information on the supported options.
- allOf:
- - $ref: /schemas/types.yaml#/definitions/uint32-array
- - minItems: 2
- maxItems: 2
- items:
- enum: [0, 1, 2, 3]
- default: 0
+ $ref: /schemas/types.yaml#/definitions/uint32-array
+ minItems: 2
+ maxItems: 2
+ items:
+ enum: [0, 1, 2, 3]
+ default: 0
adi,accumulation-deadband-microamp:
description:
This property controls the Accumulation Dead band which allows to set the
level of current below which no accumulation takes place.
- allOf:
- - $ref: /schemas/types.yaml#/definitions/uint32
+ $ref: /schemas/types.yaml#/definitions/uint32
maximum: 255
default: 0
active high, setting it to zero makets it active low. When this property
is present, the GPIO is automatically configured as output and set to
control a fan as a function of measured temperature.
- allOf:
- - $ref: /schemas/types.yaml#/definitions/uint32
+ $ref: /schemas/types.yaml#/definitions/uint32
enum: [0, 1]
default: 0
registers. Check table 13 of the datasheet for more information on the
supported options. This property cannot be used together with
adi,gpio-out-pol.
- allOf:
- - $ref: /schemas/types.yaml#/definitions/uint32-array
- - minItems: 2
- maxItems: 2
- items:
- enum: [0, 1, 2]
- default: 0
+ $ref: /schemas/types.yaml#/definitions/uint32-array
+ minItems: 2
+ maxItems: 2
+ items:
+ enum: [0, 1, 2]
+ default: 0
required:
- compatible
set to 1 the attenuator is bypassed if set to 0 the attenuator is
not bypassed. If the property is absent then the attenuator
retains it's configuration from the bios/bootloader.
- allOf:
- - $ref: /schemas/types.yaml#/definitions/uint32
- - enum: [0, 1]
+ $ref: /schemas/types.yaml#/definitions/uint32
+ enum: [0, 1]
"^adi,pwm-active-state$":
description: |
Integer array, represents the active state of the pwm outputs If set to 0
the pwm uses a logic low output for 100% duty cycle. If set to 1 the pwm
uses a logic high output for 100% duty cycle.
- allOf:
- - $ref: /schemas/types.yaml#/definitions/uint32-array
- - minItems: 3
- maxItems: 3
- items:
- enum: [0, 1]
- default: 1
+ $ref: /schemas/types.yaml#/definitions/uint32-array
+ minItems: 3
+ maxItems: 3
+ items:
+ enum: [0, 1]
+ default: 1
required:
- compatible
The gain value for the PGA function. This is 8, 4, 2 or 1.
The PGA gain affect the shunt voltage range.
The range will be equal to: pga-gain * 40mV
- allOf:
- - $ref: /schemas/types.yaml#/definitions/uint32
+ $ref: /schemas/types.yaml#/definitions/uint32
enum: [1, 2, 4, 8]
default: 8
ti,bus-range-microvolt:
description: |
This is the operating range of the bus voltage in microvolt
- allOf:
- - $ref: /schemas/types.yaml#/definitions/uint32
+ $ref: /schemas/types.yaml#/definitions/uint32
enum: [16000000, 32000000]
default: 32000000
Array of three(TMP513) or two(TMP512) n-Factor value for each remote
temperature channel.
See datasheet Table 11 for n-Factor range list and value interpretation.
- allOf:
- - $ref: /schemas/types.yaml#definitions/uint32-array
- - minItems: 2
- maxItems: 3
- items:
- default: 0x00
- minimum: 0x00
- maximum: 0xFF
+ $ref: /schemas/types.yaml#definitions/uint32-array
+ minItems: 2
+ maxItems: 3
+ items:
+ default: 0x00
+ minimum: 0x00
+ maximum: 0xFF
required:
- compatible
Fast Mode Plus speed is selected by slave.
Format is phandle to syscfg / register offset within
syscfg / register bitmask for FMP bit.
- allOf:
- - $ref: "/schemas/types.yaml#/definitions/phandle-array"
- - items:
- minItems: 3
- maxItems: 3
+ $ref: "/schemas/types.yaml#/definitions/phandle-array"
+ items:
+ minItems: 3
+ maxItems: 3
- if:
properties:
1: REFIN2(+)/REFIN2(−).
3: AVDD
If this field is left empty, internal reference is selected.
- allOf:
- - $ref: /schemas/types.yaml#/definitions/uint32
- - enum: [0, 1, 3]
+ $ref: /schemas/types.yaml#/definitions/uint32
+ enum: [0, 1, 3]
diff-channels:
description: see Documentation/devicetree/bindings/iio/adc/adc.txt
vref-supply:
description: phandle to an external regulator providing the reference voltage
- allOf:
- - $ref: /schemas/types.yaml#/definitions/phandle
+ $ref: /schemas/types.yaml#/definitions/phandle
reg:
description: spi chipselect number according to the usual spi bindings
microchip,device-addr:
description: Device address when multiple MCP3911 chips are present on the same SPI bus.
- allOf:
- - $ref: /schemas/types.yaml#/definitions/uint32
- - enum: [0, 1, 2, 3]
- - default: 0
+ $ref: /schemas/types.yaml#/definitions/uint32
+ enum: [0, 1, 2, 3]
+ default: 0
vref-supply:
description: |
description:
Phandle to system configuration controller. It can be used to control the
analog circuitry on stm32mp1.
- allOf:
- - $ref: "/schemas/types.yaml#/definitions/phandle-array"
+ $ref: "/schemas/types.yaml#/definitions/phandle-array"
interrupt-controller: true
Resolution (bits) to use for conversions:
- can be 6, 8, 10 or 12 on stm32f4
- can be 8, 10, 12, 14 or 16 on stm32h7 and stm32mp1
- allOf:
- - $ref: /schemas/types.yaml#/definitions/uint32
+ $ref: /schemas/types.yaml#/definitions/uint32
st,adc-channels:
description: |
- 16 channels, numbered from 0 to 15 (for in0..in15) on stm32f4
- 20 channels, numbered from 0 to 19 (for in0..in19) on stm32h7 and
stm32mp1.
- allOf:
- - $ref: /schemas/types.yaml#/definitions/uint32-array
+ $ref: /schemas/types.yaml#/definitions/uint32-array
st,adc-diff-channels:
description: |
required. Both properties can be used together. Some channels can be
used as single-ended and some other ones as differential (mixed). But
channels can't be configured both as single-ended and differential.
- allOf:
- - $ref: /schemas/types.yaml#/definitions/uint32-matrix
- - items:
- items:
- - description: |
- "vinp" indicates positive input number
- minimum: 0
- maximum: 19
- - description: |
- "vinn" indicates negative input number
- minimum: 0
- maximum: 19
+ $ref: /schemas/types.yaml#/definitions/uint32-matrix
+ items:
+ items:
+ - description: |
+ "vinp" indicates positive input number
+ minimum: 0
+ maximum: 19
+ - description: |
+ "vinn" indicates negative input number
+ minimum: 0
+ maximum: 19
st,min-sample-time-nsecs:
description:
array that matches "st,adc-channels" and/or "st,adc-diff-channels"
list, to set sample time resp. for all channels, or independently for
each channel.
- allOf:
- - $ref: /schemas/types.yaml#/definitions/uint32-array
+ $ref: /schemas/types.yaml#/definitions/uint32-array
allOf:
- if:
On stm32h7 and stm32mp1:
- For st,stm32-dfsdm-adc: up to 8 channels numbered from 0 to 7.
- For st,stm32-dfsdm-dmic: 1 channel numbered from 0 to 7.
- allOf:
- - $ref: /schemas/types.yaml#/definitions/uint32-array
- - items:
- minimum: 0
- maximum: 7
+ $ref: /schemas/types.yaml#/definitions/uint32-array
+ items:
+ minimum: 0
+ maximum: 7
st,adc-channel-names:
description: List of single-ended channel names.
- allOf:
- - $ref: /schemas/types.yaml#/definitions/string-array
+ $ref: /schemas/types.yaml#/definitions/string-array
st,filter-order:
description: |
- 0: FastSinC
- [1-5]: order 1 to 5.
For audio purpose it is recommended to use order 3 to 5.
- allOf:
- - $ref: /schemas/types.yaml#/definitions/uint32
- - items:
- minimum: 0
- maximum: 5
+ $ref: /schemas/types.yaml#/definitions/uint32
+ items:
+ minimum: 0
+ maximum: 5
"#io-channel-cells":
const: 1
- "MANCH_F": manchester codec, rising edge = logic 1, falling edge = logic 0
items:
enum: [ SPI_R, SPI_F, MANCH_R, MANCH_F ]
- allOf:
- - $ref: /schemas/types.yaml#/definitions/non-unique-string-array
+ $ref: /schemas/types.yaml#/definitions/non-unique-string-array
st,adc-channel-clk-src:
description: |
- "CLKOUT_R": internal SPI clock divided by 2 (rising edge).
items:
enum: [ CLKIN, CLKOUT, CLKOUT_F, CLKOUT_R ]
- allOf:
- - $ref: /schemas/types.yaml#/definitions/non-unique-string-array
+ $ref: /schemas/types.yaml#/definitions/non-unique-string-array
st,adc-alt-channel:
description:
amstaos,proximity-diodes:
description: Proximity diodes to enable
- allOf:
- - $ref: /schemas/types.yaml#/definitions/uint32-array
- - minItems: 1
- maxItems: 2
- items:
- minimum: 0
- maximum: 1
+ $ref: /schemas/types.yaml#/definitions/uint32-array
+ minItems: 1
+ maxItems: 2
+ items:
+ minimum: 0
+ maximum: 1
interrupts:
maxItems: 1
0 - 50/60Hz rejection
1 - 60Hz rejection
2 - 50Hz rejection
- allOf:
- - $ref: /schemas/types.yaml#/definitions/uint32
- - minimum: 0
- maximum: 2
+ $ref: /schemas/types.yaml#/definitions/uint32
+ minimum: 0
+ maximum: 2
'#address-cells':
const: 1
7 - Type T Thermocouple
8 - Type B Thermocouple
9 - Custom Thermocouple
- allOf:
- - $ref: /schemas/types.yaml#/definitions/uint32
+ $ref: /schemas/types.yaml#/definitions/uint32
minimum: 1
maximum: 9
more details look at table 69 and 70.
Note should be signed, but dtc doesn't currently maintain the
sign.
- allOf:
- - $ref: /schemas/types.yaml#/definitions/uint64-matrix
+ $ref: /schemas/types.yaml#/definitions/uint64-matrix
minItems: 3
maxItems: 64
items:
properties:
adi,sensor-type:
description: Identifies the sensor as a diode.
- allOf:
- - $ref: /schemas/types.yaml#/definitions/uint32
+ $ref: /schemas/types.yaml#/definitions/uint32
const: 28
adi,single-ended:
16 - RTD PT-1000 (0.00375)
17 - RTD NI-120
18 - RTD Custom
- allOf:
- - $ref: /schemas/types.yaml#/definitions/uint32
+ $ref: /schemas/types.yaml#/definitions/uint32
minimum: 10
maximum: 18
description:
Identifies the number of wires used by the RTD. Setting this
property to 5 means 4 wires with Kelvin Rsense.
- allOf:
- - $ref: /schemas/types.yaml#/definitions/uint32
- - enum: [2, 3, 4, 5]
+ $ref: /schemas/types.yaml#/definitions/uint32
+ enum: [2, 3, 4, 5]
adi,rsense-share:
description:
description:
This property set the RTD curve used and the corresponding
Callendar-VanDusen constants. Look at table 30 of the datasheet.
- allOf:
- - $ref: /schemas/types.yaml#/definitions/uint32
- - minimum: 0
- maximum: 3
+ $ref: /schemas/types.yaml#/definitions/uint32
+ minimum: 0
+ maximum: 3
adi,custom-rtd:
description:
This is a table, where each entry should be a pair of
resistance(ohm)-temperature(K). The entries added here are in uohm
and uK. For more details values look at table 74 and 75.
- allOf:
- - $ref: /schemas/types.yaml#/definitions/uint64-matrix
+ $ref: /schemas/types.yaml#/definitions/uint64-matrix
items:
minItems: 3
maxItems: 64
25 - Thermistor Spectrum 1003k 1kohm
26 - Thermistor Custom Steinhart-Hart
27 - Custom Thermistor
- allOf:
- - $ref: /schemas/types.yaml#/definitions/uint32
+ $ref: /schemas/types.yaml#/definitions/uint32
minimum: 19
maximum: 27
This property controls the magnitude of the excitation current
applied to the thermistor. Value 0 set's the sensor in auto-range
mode.
- allOf:
- - $ref: /schemas/types.yaml#/definitions/uint32
- - enum: [0, 250, 500, 1000, 5000, 10000, 25000, 50000, 100000,
- 250000, 500000, 1000000]
+ $ref: /schemas/types.yaml#/definitions/uint32
+ enum: [0, 250, 500, 1000, 5000, 10000, 25000, 50000, 100000, 250000,
+ 500000, 1000000]
adi,custom-thermistor:
description:
resistance(ohm)-temperature(K). The entries added here are in uohm
and uK only for custom thermistors. For more details look at table
78 and 79.
- allOf:
- - $ref: /schemas/types.yaml#/definitions/uint64-matrix
+ $ref: /schemas/types.yaml#/definitions/uint64-matrix
minItems: 3
maxItems: 64
items:
be programmed into the device memory using this property. For
Steinhart sensors the coefficients are given in the raw
format. Look at table 82 for more information.
- allOf:
- - $ref: /schemas/types.yaml#/definitions/uint32-array
+ $ref: /schemas/types.yaml#/definitions/uint32-array
items:
minItems: 6
maxItems: 6
properties:
adi,sensor-type:
description: Identifies the sensor as a direct adc.
- allOf:
- - $ref: /schemas/types.yaml#/definitions/uint32
+ $ref: /schemas/types.yaml#/definitions/uint32
const: 30
adi,single-ended:
adi,sensor-type:
description: Identifies the sensor as a rsense.
- allOf:
- - $ref: /schemas/types.yaml#/definitions/uint32
+ $ref: /schemas/types.yaml#/definitions/uint32
const: 29
adi,rsense-val-milli-ohms:
description: Keycode to emit
channel:
- allOf:
- - $ref: /schemas/types.yaml#/definitions/uint32
- - enum: [0, 1]
+ $ref: /schemas/types.yaml#/definitions/uint32
+ enum: [0, 1]
description: ADC Channel this key is attached to
voltage:
if:
type: object
then:
- allOf:
- - $ref: input.yaml#
+ $ref: input.yaml#
properties:
gpios:
description:
Specify event type this button/key generates. If not specified defaults to
<1> == EV_KEY.
- allOf:
- - $ref: /schemas/types.yaml#definitions/uint32
+ $ref: /schemas/types.yaml#definitions/uint32
+
default: 1
linux,input-value:
linux,input-value = <0xffffffff>; /* -1 */
- allOf:
- - $ref: /schemas/types.yaml#definitions/uint32
+ $ref: /schemas/types.yaml#definitions/uint32
debounce-interval:
description:
Debouncing interval time in milliseconds. If not specified defaults to 5.
- allOf:
- - $ref: /schemas/types.yaml#definitions/uint32
+ $ref: /schemas/types.yaml#definitions/uint32
+
default: 5
wakeup-source:
EV_ACT_ANY - both asserted and deasserted
EV_ACT_ASSERTED - asserted
EV_ACT_DEASSERTED - deasserted
- allOf:
- - $ref: /schemas/types.yaml#definitions/uint32
- enum: [ 0, 1, 2 ]
+ $ref: /schemas/types.yaml#definitions/uint32
+ enum: [0, 1, 2]
linux,can-disable:
description:
description:
Specifies an array of numeric keycode values to be used for reporting
button presses.
- allOf:
- - $ref: /schemas/types.yaml#/definitions/uint32-array
- - items:
- minimum: 0
- maximum: 0xff
+ $ref: /schemas/types.yaml#/definitions/uint32-array
+ items:
+ minimum: 0
+ maximum: 0xff
poll-interval:
description: Poll interval time in milliseconds.
- azoteq,iqs625-keys
linux,keycodes:
- allOf:
- - $ref: /schemas/types.yaml#/definitions/uint32-array
- - minItems: 1
- maxItems: 16
+ $ref: /schemas/types.yaml#/definitions/uint32-array
+ minItems: 1
+ maxItems: 16
description: |
Specifies the numeric keycodes associated with each available touch or
proximity event according to the following table. An 'x' indicates the
gain:
description: Allows setting the sensitivity in the range from 0 to 31.
Note that lower values indicate higher sensitivity.
- allOf:
- - $ref: /schemas/types.yaml#/definitions/uint32
- - minimum: 0
- - maximum: 31
+ $ref: /schemas/types.yaml#/definitions/uint32
+ minimum: 0
+ maximum: 31
offset:
description: Allows setting the edge compensation in the range from 0 to 31.
- allOf:
- - $ref: /schemas/types.yaml#/definitions/uint32
- - minimum: 0
- - maximum: 31
+ $ref: /schemas/types.yaml#/definitions/uint32
+ minimum: 0
+ maximum: 31
offset-x:
description: Same as offset, but applies only to the horizontal position.
Range from 0 to 80, only supported by evervision,ev-ft5726 devices.
- allOf:
- - $ref: /schemas/types.yaml#/definitions/uint32
- - minimum: 0
- - maximum: 80
+ $ref: /schemas/types.yaml#/definitions/uint32
+ minimum: 0
+ maximum: 80
offset-y:
description: Same as offset, but applies only to the vertical position.
Range from 0 to 80, only supported by evervision,ev-ft5726 devices.
- allOf:
- - $ref: /schemas/types.yaml#/definitions/uint32
- - minimum: 0
- - maximum: 80
+ $ref: /schemas/types.yaml#/definitions/uint32
+ minimum: 0
+ maximum: 80
touchscreen-size-x: true
touchscreen-size-y: true
description:
If using padding pages, specifies the stride of consecutive
redistributors. Must be a multiple of 64kB.
- allOf:
- - $ref: /schemas/types.yaml#/definitions/uint64
- - multipleOf: 0x10000
- exclusiveMinimum: 0
+ $ref: /schemas/types.yaml#/definitions/uint64
+ multipleOf: 0x10000
+ exclusiveMinimum: 0
"#redistributor-regions":
description:
The number of independent contiguous regions occupied by the
redistributors. Required if more than one such region is present.
- allOf:
- - $ref: /schemas/types.yaml#/definitions/uint32
- - maximum: 4096 # Should be enough?
+ $ref: /schemas/types.yaml#/definitions/uint32
+ maximum: 4096
msi-controller:
description:
A list of pairs <intid span>, where "intid" is the first SPI of a range
that can be used an MBI, and "span" the size of that range. Multiple
ranges can be provided.
- allOf:
- - $ref: /schemas/types.yaml#/definitions/uint32-matrix
- - items:
- minItems: 2
- maxItems: 2
+ $ref: /schemas/types.yaml#/definitions/uint32-matrix
+ items:
+ minItems: 2
+ maxItems: 2
mbi-alias:
description:
Address property. Base address of an alias of the GICD region containing
only the {SET,CLR}SPI registers to be used if isolation is required,
and if supported by the HW.
- allOf:
- - $ref: /schemas/types.yaml#/definitions/uint32-array
- - items:
- minItems: 1
- maxItems: 2
+ $ref: /schemas/types.yaml#/definitions/uint32-array
+ items:
+ minItems: 1
+ maxItems: 2
ppi-partitions:
type: object
description:
(u32, u32) tuple describing the untranslated
address and size of the pre-ITS window.
- allOf:
- - $ref: /schemas/types.yaml#/definitions/uint32-array
- - items:
- minItems: 2
- maxItems: 2
+ $ref: /schemas/types.yaml#/definitions/uint32-array
+ items:
+ minItems: 2
+ maxItems: 2
required:
- compatible
and each bit in the cell refers to a children interrupt fron 0 to 31.
If a CPU interrupt line didn't connected with liointc, then keep it's
cell with zero.
- allOf:
- - $ref: /schemas/types.yaml#/definitions/uint32-array
- - minItems: 4
- maxItems: 4
-
+ $ref: /schemas/types.yaml#/definitions/uint32-array
+ minItems: 4
+ maxItems: 4
required:
- compatible
'#global-interrupts':
description: The number of global interrupts exposed by the device.
- allOf:
- - $ref: /schemas/types.yaml#/definitions/uint32
+ $ref: /schemas/types.yaml#/definitions/uint32
minimum: 0
maximum: 260 # 2 secure, 2 non-secure, and up to 256 perf counters
Color of the LED. Use one of the LED_COLOR_ID_* prefixed definitions from
the header include/dt-bindings/leds/common.h. If there is no matching
LED_COLOR_ID available, add a new one.
- allOf:
- - $ref: /schemas/types.yaml#definitions/uint32
+ $ref: /schemas/types.yaml#definitions/uint32
minimum: 0
maximum: 8
produced where the LED momentarily turns off (or on). The "keep" setting
will keep the LED at whatever its current state is, without producing a
glitch.
- allOf:
- - $ref: /schemas/types.yaml#definitions/string
+ $ref: /schemas/types.yaml#definitions/string
enum:
- on
- off
description:
This parameter, if present, is a string defining the trigger assigned to
the LED.
- allOf:
- - $ref: /schemas/types.yaml#definitions/string
+ $ref: /schemas/types.yaml#definitions/string
+
enum:
# LED will act as a back-light, controlled by the framebuffer system
- backlight
brightness and duration (in ms). The exact format is
described in:
Documentation/devicetree/bindings/leds/leds-trigger-pattern.txt
- allOf:
- - $ref: /schemas/types.yaml#definitions/uint32-matrix
+ $ref: /schemas/types.yaml#definitions/uint32-matrix
items:
minItems: 2
maxItems: 2
"(^led-[0-9a-f]$|led)":
type: object
- allOf:
- - $ref: common.yaml#
+ $ref: common.yaml#
properties:
gpios:
#- $ref: "common.yaml#"
rohm,led-compatible:
description: LED identification string
- allOf:
- - $ref: "/schemas/types.yaml#/definitions/string"
- - enum:
- - bd71828-ambled
- - bd71828-grnled
+ $ref: "/schemas/types.yaml#/definitions/string"
+ enum:
+ - bd71828-ambled
+ - bd71828-grnled
function:
description:
Purpose of LED as defined in dt-bindings/leds/common.h
st,proc-id:
description: Processor id using the mailbox (0 or 1)
- allOf:
- - $ref: /schemas/types.yaml#/definitions/uint32
- - enum: [ 0, 1 ]
+ $ref: /schemas/types.yaml#/definitions/uint32
+ enum: [0, 1]
required:
- compatible
amlogic,ao-sysctrl:
description: should point to the AOBUS sysctrl node
- allOf:
- - $ref: /schemas/types.yaml#/definitions/phandle
+ $ref: /schemas/types.yaml#/definitions/phandle
amlogic,canvas:
description: should point to a canvas provider node
- allOf:
- - $ref: /schemas/types.yaml#/definitions/phandle
+ $ref: /schemas/types.yaml#/definitions/phandle
allOf:
- if:
hdmi-phandle:
description: phandle to the HDMI controller
- allOf:
- - $ref: /schemas/types.yaml#/definitions/phandle
+ $ref: /schemas/types.yaml#/definitions/phandle
allOf:
- if:
otherwise it's continuous.
link-frequencies:
- allOf:
- - $ref: /schemas/types.yaml#/definitions/uint64-array
+ $ref: /schemas/types.yaml#/definitions/uint64-array
description:
Allowed data bus frequencies.
description:
Specifies the scancode/key mapping table defined in-kernel for
the remote controller.
- allOf:
- - $ref: '/schemas/types.yaml#/definitions/string'
- - enum:
- - rc-adstech-dvb-t-pci
- - rc-alink-dtu-m
- - rc-anysee
- - rc-apac-viewcomp
- - rc-astrometa-t2hybrid
- - rc-asus-pc39
- - rc-asus-ps3-100
- - rc-ati-tv-wonder-hd-600
- - rc-ati-x10
- - rc-avermedia
- - rc-avermedia-a16d
- - rc-avermedia-cardbus
- - rc-avermedia-dvbt
- - rc-avermedia-m135a
- - rc-avermedia-m733a-rm-k6
- - rc-avermedia-rm-ks
- - rc-avertv-303
- - rc-azurewave-ad-tu700
- - rc-beelink-gs1
- - rc-behold
- - rc-behold-columbus
- - rc-budget-ci-old
- - rc-cec
- - rc-cinergy
- - rc-cinergy-1400
- - rc-d680-dmb
- - rc-delock-61959
- - rc-dib0700-nec
- - rc-dib0700-rc5
- - rc-digitalnow-tinytwin
- - rc-digittrade
- - rc-dm1105-nec
- - rc-dntv-live-dvb-t
- - rc-dntv-live-dvbt-pro
- - rc-dtt200u
- - rc-dvbsky
- - rc-dvico-mce
- - rc-dvico-portable
- - rc-em-terratec
- - rc-empty
- - rc-encore-enltv
- - rc-encore-enltv-fm53
- - rc-encore-enltv2
- - rc-evga-indtube
- - rc-eztv
- - rc-flydvb
- - rc-flyvideo
- - rc-fusionhdtv-mce
- - rc-gadmei-rm008z
- - rc-geekbox
- - rc-genius-tvgo-a11mce
- - rc-gotview7135
- - rc-hauppauge
- - rc-hisi-poplar
- - rc-hisi-tv-demo
- - rc-imon-mce
- - rc-imon-pad
- - rc-imon-rsc
- - rc-iodata-bctv7e
- - rc-it913x-v1
- - rc-it913x-v2
- - rc-kaiomy
- - rc-khadas
- - rc-kworld-315u
- - rc-kworld-pc150u
- - rc-kworld-plus-tv-analog
- - rc-leadtek-y04g0051
- - rc-lme2510
- - rc-manli
- - rc-medion-x10
- - rc-medion-x10-digitainer
- - rc-medion-x10-or2x
- - rc-msi-digivox-ii
- - rc-msi-digivox-iii
- - rc-msi-tvanywhere
- - rc-msi-tvanywhere-plus
- - rc-nebula
- - rc-nec-terratec-cinergy-xs
- - rc-norwood
- - rc-npgtech
- - rc-odroid
- - rc-pctv-sedna
- - rc-pinnacle-color
- - rc-pinnacle-grey
- - rc-pinnacle-pctv-hd
- - rc-pixelview
- - rc-pixelview-002t
- - rc-pixelview-mk12
- - rc-pixelview-new
- - rc-powercolor-real-angel
- - rc-proteus-2309
- - rc-purpletv
- - rc-pv951
- - rc-rc5-tv
- - rc-rc6-mce
- - rc-real-audio-220-32-keys
- - rc-reddo
- - rc-snapstream-firefly
- - rc-streamzap
- - rc-su3000
- - rc-tango
- - rc-tanix-tx3mini
- - rc-tanix-tx5max
- - rc-tbs-nec
- - rc-technisat-ts35
- - rc-technisat-usb2
- - rc-terratec-cinergy-c-pci
- - rc-terratec-cinergy-s2-hd
- - rc-terratec-cinergy-xs
- - rc-terratec-slim
- - rc-terratec-slim-2
- - rc-tevii-nec
- - rc-tivo
- - rc-total-media-in-hand
- - rc-total-media-in-hand-02
- - rc-trekstor
- - rc-tt-1500
- - rc-twinhan-dtv-cab-ci
- - rc-twinhan1027
- - rc-videomate-k100
- - rc-videomate-s350
- - rc-videomate-tv-pvr
- - rc-videostrong-kii-pro
- - rc-wetek-hub
- - rc-wetek-play2
- - rc-winfast
- - rc-winfast-usbii-deluxe
- - rc-x96max
- - rc-xbox-dvd
- - rc-zx-irdec
+ $ref: '/schemas/types.yaml#/definitions/string'
+ enum:
+ - rc-adstech-dvb-t-pci
+ - rc-alink-dtu-m
+ - rc-anysee
+ - rc-apac-viewcomp
+ - rc-astrometa-t2hybrid
+ - rc-asus-pc39
+ - rc-asus-ps3-100
+ - rc-ati-tv-wonder-hd-600
+ - rc-ati-x10
+ - rc-avermedia
+ - rc-avermedia-a16d
+ - rc-avermedia-cardbus
+ - rc-avermedia-dvbt
+ - rc-avermedia-m135a
+ - rc-avermedia-m733a-rm-k6
+ - rc-avermedia-rm-ks
+ - rc-avertv-303
+ - rc-azurewave-ad-tu700
+ - rc-beelink-gs1
+ - rc-behold
+ - rc-behold-columbus
+ - rc-budget-ci-old
+ - rc-cec
+ - rc-cinergy
+ - rc-cinergy-1400
+ - rc-d680-dmb
+ - rc-delock-61959
+ - rc-dib0700-nec
+ - rc-dib0700-rc5
+ - rc-digitalnow-tinytwin
+ - rc-digittrade
+ - rc-dm1105-nec
+ - rc-dntv-live-dvb-t
+ - rc-dntv-live-dvbt-pro
+ - rc-dtt200u
+ - rc-dvbsky
+ - rc-dvico-mce
+ - rc-dvico-portable
+ - rc-em-terratec
+ - rc-empty
+ - rc-encore-enltv
+ - rc-encore-enltv-fm53
+ - rc-encore-enltv2
+ - rc-evga-indtube
+ - rc-eztv
+ - rc-flydvb
+ - rc-flyvideo
+ - rc-fusionhdtv-mce
+ - rc-gadmei-rm008z
+ - rc-geekbox
+ - rc-genius-tvgo-a11mce
+ - rc-gotview7135
+ - rc-hauppauge
+ - rc-hisi-poplar
+ - rc-hisi-tv-demo
+ - rc-imon-mce
+ - rc-imon-pad
+ - rc-imon-rsc
+ - rc-iodata-bctv7e
+ - rc-it913x-v1
+ - rc-it913x-v2
+ - rc-kaiomy
+ - rc-khadas
+ - rc-kworld-315u
+ - rc-kworld-pc150u
+ - rc-kworld-plus-tv-analog
+ - rc-leadtek-y04g0051
+ - rc-lme2510
+ - rc-manli
+ - rc-medion-x10
+ - rc-medion-x10-digitainer
+ - rc-medion-x10-or2x
+ - rc-msi-digivox-ii
+ - rc-msi-digivox-iii
+ - rc-msi-tvanywhere
+ - rc-msi-tvanywhere-plus
+ - rc-nebula
+ - rc-nec-terratec-cinergy-xs
+ - rc-norwood
+ - rc-npgtech
+ - rc-odroid
+ - rc-pctv-sedna
+ - rc-pinnacle-color
+ - rc-pinnacle-grey
+ - rc-pinnacle-pctv-hd
+ - rc-pixelview
+ - rc-pixelview-002t
+ - rc-pixelview-mk12
+ - rc-pixelview-new
+ - rc-powercolor-real-angel
+ - rc-proteus-2309
+ - rc-purpletv
+ - rc-pv951
+ - rc-rc5-tv
+ - rc-rc6-mce
+ - rc-real-audio-220-32-keys
+ - rc-reddo
+ - rc-snapstream-firefly
+ - rc-streamzap
+ - rc-su3000
+ - rc-tango
+ - rc-tanix-tx3mini
+ - rc-tanix-tx5max
+ - rc-tbs-nec
+ - rc-technisat-ts35
+ - rc-technisat-usb2
+ - rc-terratec-cinergy-c-pci
+ - rc-terratec-cinergy-s2-hd
+ - rc-terratec-cinergy-xs
+ - rc-terratec-slim
+ - rc-terratec-slim-2
+ - rc-tevii-nec
+ - rc-tivo
+ - rc-total-media-in-hand
+ - rc-total-media-in-hand-02
+ - rc-trekstor
+ - rc-tt-1500
+ - rc-twinhan-dtv-cab-ci
+ - rc-twinhan1027
+ - rc-videomate-k100
+ - rc-videomate-s350
+ - rc-videomate-tv-pvr
+ - rc-videostrong-kii-pro
+ - rc-wetek-hub
+ - rc-wetek-play2
+ - rc-winfast
+ - rc-winfast-usbii-deluxe
+ - rc-x96max
+ - rc-xbox-dvd
+ - rc-zx-irdec
#The per-board settings for Gen3 and RZ/G2 platforms:
renesas,id:
description: VIN channel number
- allOf:
- - $ref: /schemas/types.yaml#/definitions/uint32
- - minimum: 0
- - maximum: 15
+ $ref: /schemas/types.yaml#/definitions/uint32
+ minimum: 0
+ maximum: 15
ports:
type: object
type: boolean
samsung,srom-timing:
- allOf:
- - $ref: /schemas/types.yaml#/definitions/uint32-array
- - items:
- minItems: 6
- maxItems: 6
+ $ref: /schemas/types.yaml#/definitions/uint32-array
+ items:
+ minItems: 6
+ maxItems: 6
description: |
Array of 6 integers, specifying bank timings in the following order:
Tacp, Tcah, Tcoh, Tacc, Tcos, Tacs.
timings
nvidia,emc-auto-cal-interval:
- allOf:
- - $ref: /schemas/types.yaml#/definitions/uint32
description:
pad calibration interval in microseconds
+ $ref: /schemas/types.yaml#/definitions/uint32
minimum: 0
maximum: 2097151
value of the EMC_XM2DQSPADCTRL2 register for this set of timings
nvidia,emc-zcal-cnt-long:
- allOf:
- - $ref: /schemas/types.yaml#/definitions/uint32
description:
number of EMC clocks to wait before issuing any commands after
clock change
+ $ref: /schemas/types.yaml#/definitions/uint32
minimum: 0
maximum: 1023
value of the EMC_ZCAL_INTERVAL register for this set of timings
nvidia,emc-configuration:
- allOf:
- - $ref: /schemas/types.yaml#/definitions/uint32-array
description:
EMC timing characterization data. These are the registers (see
section "15.6.2 EMC Registers" in the TRM) whose values need to
be specified, according to the board documentation.
+ $ref: /schemas/types.yaml#/definitions/uint32-array
items:
- description: EMC_RC
- description: EMC_RFC
maximum: 1066000000
nvidia,emem-configuration:
- allOf:
- - $ref: /schemas/types.yaml#/definitions/uint32-array
+ $ref: /schemas/types.yaml#/definitions/uint32-array
description: |
Values to be written to the EMEM register block. See section
"15.6.1 MC Registers" in the TRM.
maximum: 900000000
nvidia,emc-auto-cal-interval:
- allOf:
- - $ref: /schemas/types.yaml#/definitions/uint32
description:
Pad calibration interval in microseconds.
+ $ref: /schemas/types.yaml#/definitions/uint32
minimum: 0
maximum: 2097151
Mode Register 0.
nvidia,emc-zcal-cnt-long:
- allOf:
- - $ref: /schemas/types.yaml#/definitions/uint32
description:
Number of EMC clocks to wait before issuing any commands after
sending ZCAL_MRW_CMD.
+ $ref: /schemas/types.yaml#/definitions/uint32
minimum: 0
maximum: 1023
FBIO "read" FIFO periodic resetting enabled.
nvidia,emc-configuration:
- allOf:
- - $ref: /schemas/types.yaml#/definitions/uint32-array
description:
EMC timing characterization data. These are the registers
(see section "18.13.2 EMC Registers" in the TRM) whose values
need to be specified, according to the board documentation.
+ $ref: /schemas/types.yaml#/definitions/uint32-array
items:
- description: EMC_RC
- description: EMC_RFC
maximum: 900000000
nvidia,emem-configuration:
- allOf:
- - $ref: /schemas/types.yaml#/definitions/uint32-array
+ $ref: /schemas/types.yaml#/definitions/uint32-array
description: |
Values to be written to the EMEM register block. See section
"18.13.1 MC Registers" in the TRM.
description: A touchscreen is attached to the controller
allwinner,tp-sensitive-adjust:
- allOf:
- - $ref: /schemas/types.yaml#/definitions/uint32
- - minimum: 0
- maximum: 15
- default: 15
+ $ref: /schemas/types.yaml#/definitions/uint32
+ minimum: 0
+ maximum: 15
+ default: 15
+
description: Sensitivity of pen down detection
allwinner,filter-type:
- allOf:
- - $ref: /schemas/types.yaml#/definitions/uint32
- - minimum: 0
- maximum: 3
- default: 1
+ $ref: /schemas/types.yaml#/definitions/uint32
+ minimum: 0
+ maximum: 3
+ default: 1
+
description: |
Select median and averaging filter. Sample used for median /
averaging filter:
description:
One or two <index level filter> to describe break input
configurations.
- allOf:
- - $ref: /schemas/types.yaml#/definitions/uint32-matrix
- - items:
- items:
- - description: |
- "index" indicates on which break input (0 or 1) the
- configuration should be applied.
- enum: [ 0 , 1]
- - description: |
- "level" gives the active level (0=low or 1=high) of the
- input signal for this configuration
- enum: [ 0, 1 ]
- - description: |
- "filter" gives the filtering value (up to 15) to be applied.
- maximum: 15
- minItems: 1
- maxItems: 2
+ $ref: /schemas/types.yaml#/definitions/uint32-matrix
+ items:
+ items:
+ - description: |
+ "index" indicates on which break input (0 or 1) the
+ configuration should be applied.
+ enum: [0, 1]
+ - description: |
+ "level" gives the active level (0=low or 1=high) of the
+ input signal for this configuration
+ enum: [0, 1]
+ - description: |
+ "filter" gives the filtering value (up to 15) to be applied.
+ maximum: 15
+ minItems: 1
+ maxItems: 2
required:
- "#pwm-cells"
onkey:
type: object
- allOf:
- - $ref: ../input/input.yaml
+ $ref: ../input/input.yaml
properties:
compatible:
watchdog:
type: object
- allOf:
- - $ref: ../watchdog/watchdog.yaml
+ $ref: ../watchdog/watchdog.yaml
properties:
compatible:
description: STPMIC1 voltage regulators supplies
"^(buck[1-4]|ldo[1-6]|boost|vref_ddr|pwr_sw[1-2])$":
- allOf:
- - $ref: ../regulator/regulator.yaml
+ $ref: ../regulator/regulator.yaml
"^ldo[1-2,5-6]$":
type: object
description: |
The size (in bytes) of the IO accesses that should be performed
on the device.
- allOf:
- - $ref: /schemas/types.yaml#/definitions/uint32
- - enum: [ 1, 2, 4, 8 ]
+ $ref: /schemas/types.yaml#/definitions/uint32
+ enum: [1, 2, 4, 8]
hwlocks:
maxItems: 1
patternProperties:
"^sdhci@[0-9a-f]+$":
type: object
- allOf:
- - $ref: mmc-controller.yaml
+ $ref: mmc-controller.yaml
+
properties:
compatible:
enum:
cdns,phy-input-delay-sd-highspeed:
description: Value of the delay in the input path for SD high-speed timing
- allOf:
- - $ref: "/schemas/types.yaml#/definitions/uint32"
- - minimum: 0
- - maximum: 0x1f
+ $ref: "/schemas/types.yaml#/definitions/uint32"
+ minimum: 0
+ maximum: 0x1f
cdns,phy-input-delay-legacy:
description: Value of the delay in the input path for legacy timing
- allOf:
- - $ref: "/schemas/types.yaml#/definitions/uint32"
- - minimum: 0
- - maximum: 0x1f
+ $ref: "/schemas/types.yaml#/definitions/uint32"
+ minimum: 0
+ maximum: 0x1f
cdns,phy-input-delay-sd-uhs-sdr12:
description: Value of the delay in the input path for SD UHS SDR12 timing
- allOf:
- - $ref: "/schemas/types.yaml#/definitions/uint32"
- - minimum: 0
- - maximum: 0x1f
+ $ref: "/schemas/types.yaml#/definitions/uint32"
+ minimum: 0
+ maximum: 0x1f
cdns,phy-input-delay-sd-uhs-sdr25:
description: Value of the delay in the input path for SD UHS SDR25 timing
- allOf:
- - $ref: "/schemas/types.yaml#/definitions/uint32"
- - minimum: 0
- - maximum: 0x1f
+ $ref: "/schemas/types.yaml#/definitions/uint32"
+ minimum: 0
+ maximum: 0x1f
cdns,phy-input-delay-sd-uhs-sdr50:
description: Value of the delay in the input path for SD UHS SDR50 timing
- allOf:
- - $ref: "/schemas/types.yaml#/definitions/uint32"
- - minimum: 0
- - maximum: 0x1f
+ $ref: "/schemas/types.yaml#/definitions/uint32"
+ minimum: 0
+ maximum: 0x1f
cdns,phy-input-delay-sd-uhs-ddr50:
description: Value of the delay in the input path for SD UHS DDR50 timing
- allOf:
- - $ref: "/schemas/types.yaml#/definitions/uint32"
- - minimum: 0
- - maximum: 0x1f
+ $ref: "/schemas/types.yaml#/definitions/uint32"
+ minimum: 0
+ maximum: 0x1f
cdns,phy-input-delay-mmc-highspeed:
description: Value of the delay in the input path for MMC high-speed timing
- allOf:
- - $ref: "/schemas/types.yaml#/definitions/uint32"
- - minimum: 0
- - maximum: 0x1f
+ $ref: "/schemas/types.yaml#/definitions/uint32"
+ minimum: 0
+ maximum: 0x1f
cdns,phy-input-delay-mmc-ddr:
description: Value of the delay in the input path for eMMC high-speed DDR timing
- allOf:
- - $ref: "/schemas/types.yaml#/definitions/uint32"
- - minimum: 0
- - maximum: 0x1f
# PHY DLL clock delays:
# Each delay property represents the fraction of the clock period.
# The approximate delay value will be
# (<delay property value>/128)*sdmclk_clock_period.
+ $ref: "/schemas/types.yaml#/definitions/uint32"
+ minimum: 0
+ maximum: 0x1f
cdns,phy-dll-delay-sdclk:
description: |
Value of the delay introduced on the sdclk output for all modes except
HS200, HS400 and HS400_ES.
- allOf:
- - $ref: "/schemas/types.yaml#/definitions/uint32"
- - minimum: 0
- - maximum: 0x7f
+ $ref: "/schemas/types.yaml#/definitions/uint32"
+ minimum: 0
+ maximum: 0x7f
cdns,phy-dll-delay-sdclk-hsmmc:
description: |
Value of the delay introduced on the sdclk output for HS200, HS400 and
HS400_ES speed modes.
- allOf:
- - $ref: "/schemas/types.yaml#/definitions/uint32"
- - minimum: 0
- - maximum: 0x7f
+ $ref: "/schemas/types.yaml#/definitions/uint32"
+ minimum: 0
+ maximum: 0x7f
cdns,phy-dll-delay-strobe:
description: |
Value of the delay introduced on the dat_strobe input used in
HS400 / HS400_ES speed modes.
- allOf:
- - $ref: "/schemas/types.yaml#/definitions/uint32"
- - minimum: 0
- - maximum: 0x7f
+ $ref: "/schemas/types.yaml#/definitions/uint32"
+ minimum: 0
+ maximum: 0x7f
required:
- compatible
# Other properties
bus-width:
- allOf:
- - $ref: /schemas/types.yaml#/definitions/uint32
- - enum: [1, 4, 8]
- default: 1
description:
Number of data lines.
+ $ref: /schemas/types.yaml#/definitions/uint32
+ enum: [1, 4, 8]
+ default: 1
max-frequency:
- allOf:
- - $ref: /schemas/types.yaml#/definitions/uint32
- - minimum: 400000
- - maximum: 200000000
description:
Maximum operating frequency of the bus.
+ $ref: /schemas/types.yaml#/definitions/uint32
+ minimum: 400000
+ maximum: 200000000
disable-wp:
$ref: /schemas/types.yaml#/definitions/flag
eMMC HS400 enhanced strobe mode is supported
dsr:
- allOf:
- - $ref: /schemas/types.yaml#/definitions/uint32
- - minimum: 0
- - maximum: 0xffff
description:
Value the card Driver Stage Register (DSR) should be programmed
with.
+ $ref: /schemas/types.yaml#/definitions/uint32
+ minimum: 0
+ maximum: 0xffff
no-sdio:
$ref: /schemas/types.yaml#/definitions/flag
initialization.
fixed-emmc-driver-type:
- allOf:
- - $ref: /schemas/types.yaml#/definitions/uint32
- - minimum: 0
- - maximum: 4
description:
For non-removable eMMC, enforce this driver type. The value is
the driver type as specified in the eMMC specification (table
206 in spec version 5.1)
+ $ref: /schemas/types.yaml#/definitions/uint32
+ minimum: 0
+ maximum: 4
post-power-on-delay-ms:
- allOf:
- - $ref: /schemas/types.yaml#/definitions/uint32
- - default: 10
description:
It was invented for MMC pwrseq-simple which could be referred to
mmc-pwrseq-simple.txt. But now it\'s reused as a tunable delay
waiting for I/O signalling and card power supply to be stable,
regardless of whether pwrseq-simple is used. Default to 10ms if
no available.
+ $ref: /schemas/types.yaml#/definitions/uint32
+ default: 10
supports-cqe:
$ref: /schemas/types.yaml#/definitions/flag
- reg
"^clk-phase-(legacy|sd-hs|mmc-(hs|hs[24]00|ddr52)|uhs-(sdr(12|25|50|104)|ddr50))$":
- allOf:
- - $ref: /schemas/types.yaml#/definitions/uint32-array
+ $ref: /schemas/types.yaml#/definitions/uint32-array
+
minItems: 2
maxItems: 2
items:
high speed modes.
rockchip,default-sample-phase:
- allOf:
- - $ref: /schemas/types.yaml#/definitions/uint32
+ $ref: /schemas/types.yaml#/definitions/uint32
minimum: 0
maximum: 360
default: 0
If not specified 0 deg will be used.
rockchip,desired-num-phases:
- allOf:
- - $ref: /schemas/types.yaml#/definitions/uint32
+ $ref: /schemas/types.yaml#/definitions/uint32
minimum: 0
maximum: 360
default: 360
clock to this at probe time.
fifo-depth:
- allOf:
- - $ref: /schemas/types.yaml#/definitions/uint32
description:
The maximum size of the tx/rx fifo's. If this property is not
specified, the default value of the fifo size is determined from the
controller registers.
+ $ref: /schemas/types.yaml#/definitions/uint32
card-detect-delay:
- allOf:
- - $ref: /schemas/types.yaml#/definitions/uint32
- - default: 0
description:
Delay in milli-seconds before detecting card after card
insert event. The default value is 0.
+ $ref: /schemas/types.yaml#/definitions/uint32
+ default: 0
data-addr:
- allOf:
- - $ref: /schemas/types.yaml#/definitions/uint32
description:
Override fifo address with value provided by DT. The default FIFO reg
offset is assumed as 0x100 (version < 0x240A) and 0x200(version >= 0x240A)
by driver. If the controller does not follow this rule, please use
this property to set fifo address in device tree.
+ $ref: /schemas/types.yaml#/definitions/uint32
fifo-watermark-aligned:
- allOf:
- - $ref: /schemas/types.yaml#/definitions/flag
description:
Data done irq is expected if data length is less than
watermark in PIO mode. But fifo watermark is requested to be aligned
with data length in some SoC so that TX/RX irq can be generated with
data done irq. Add this watermark quirk to mark this requirement and
force fifo watermark setting accordingly.
+ $ref: /schemas/types.yaml#/definitions/flag
dmas:
maxItems: 1
allwinner,rb:
description:
Contains the native Ready/Busy IDs.
- allOf:
- - $ref: /schemas/types.yaml#/definitions/uint32-array
- - minItems: 1
- maxItems: 2
- items:
- minimum: 0
- maximum: 1
+ $ref: /schemas/types.yaml#/definitions/uint32-array
+ minItems: 1
+ maxItems: 2
+ items:
+ minimum: 0
+ maximum: 1
additionalProperties: false
Contains the native Ready/Busy IDs.
nand-ecc-mode:
- allOf:
- - $ref: /schemas/types.yaml#/definitions/string
- - enum: [ none, soft, hw, hw_syndrome, hw_oob_first, on-die ]
description:
Desired ECC engine, either hardware (most of the time
embedded in the NAND controller) or software correction
(Linux will handle the calculations). soft_bch is deprecated
and should be replaced by soft and nand-ecc-algo.
+ $ref: /schemas/types.yaml#/definitions/string
+ enum: [none, soft, hw, hw_syndrome, hw_oob_first, on-die]
nand-ecc-algo:
- allOf:
- - $ref: /schemas/types.yaml#/definitions/string
- - enum: [ hamming, bch, rs ]
description:
Desired ECC algorithm.
+ $ref: /schemas/types.yaml#/definitions/string
+ enum: [hamming, bch, rs]
nand-bus-width:
- allOf:
- - $ref: /schemas/types.yaml#/definitions/uint32
- - enum: [ 8, 16 ]
- - default: 8
description:
Bus width to the NAND chip
+ $ref: /schemas/types.yaml#/definitions/uint32
+ enum: [8, 16]
+ default: 8
nand-on-flash-bbt:
$ref: /schemas/types.yaml#/definitions/flag
build a volatile BBT in RAM.
nand-ecc-strength:
- allOf:
- - $ref: /schemas/types.yaml#/definitions/uint32
- - minimum: 1
description:
Maximum number of bits that can be corrected per ECC step.
+ $ref: /schemas/types.yaml#/definitions/uint32
+ minimum: 1
nand-ecc-step-size:
- allOf:
- - $ref: /schemas/types.yaml#/definitions/uint32
- - minimum: 1
description:
Number of data bytes covered by a single ECC step.
+ $ref: /schemas/types.yaml#/definitions/uint32
+ minimum: 1
nand-ecc-maximize:
$ref: /schemas/types.yaml#/definitions/flag
Please refer to 2.4.1 Message RAM Configuration in Bosch
M_CAN user manual for details.
- allOf:
- - $ref: /schemas/types.yaml#/definitions/int32-array
- - items:
- items:
- - description: The 'offset' is an address offset of the Message RAM
- where the following elements start from. This is usually
- set to 0x0 if you're using a private Message RAM.
- default: 0
- - description: 11-bit Filter 0-128 elements / 0-128 words
- minimum: 0
- maximum: 128
- - description: 29-bit Filter 0-64 elements / 0-128 words
- minimum: 0
- maximum: 64
- - description: Rx FIFO 0 0-64 elements / 0-1152 words
- minimum: 0
- maximum: 64
- - description: Rx FIFO 1 0-64 elements / 0-1152 words
- minimum: 0
- maximum: 64
- - description: Rx Buffers 0-64 elements / 0-1152 words
- minimum: 0
- maximum: 64
- - description: Tx Event FIFO 0-32 elements / 0-64 words
- minimum: 0
- maximum: 32
- - description: Tx Buffers 0-32 elements / 0-576 words
- minimum: 0
- maximum: 32
- maxItems: 1
+ $ref: /schemas/types.yaml#/definitions/int32-array
+ items:
+ items:
+ - description: The 'offset' is an address offset of the Message RAM where
+ the following elements start from. This is usually set to 0x0 if
+ you're using a private Message RAM.
+ default: 0
+ - description: 11-bit Filter 0-128 elements / 0-128 words
+ minimum: 0
+ maximum: 128
+ - description: 29-bit Filter 0-64 elements / 0-128 words
+ minimum: 0
+ maximum: 64
+ - description: Rx FIFO 0 0-64 elements / 0-1152 words
+ minimum: 0
+ maximum: 64
+ - description: Rx FIFO 1 0-64 elements / 0-1152 words
+ minimum: 0
+ maximum: 64
+ - description: Rx Buffers 0-64 elements / 0-1152 words
+ minimum: 0
+ maximum: 64
+ - description: Tx Event FIFO 0-32 elements / 0-64 words
+ minimum: 0
+ maximum: 32
+ - description: Tx Buffers 0-32 elements / 0-576 words
+ minimum: 0
+ maximum: 32
+ maxItems: 1
can-transceiver:
$ref: can-transceiver.yaml#
pattern: "^ethernet(@.*)?$"
local-mac-address:
- allOf:
- - $ref: /schemas/types.yaml#definitions/uint8-array
- - items:
- - minItems: 6
- maxItems: 6
description:
Specifies the MAC address that was assigned to the network device.
+ $ref: /schemas/types.yaml#definitions/uint8-array
+ items:
+ - minItems: 6
+ maxItems: 6
mac-address:
- allOf:
- - $ref: /schemas/types.yaml#definitions/uint8-array
- - items:
- - minItems: 6
- maxItems: 6
description:
Specifies the MAC address that was last used by the boot
program; should be used in cases where the MAC address assigned
to the device by the boot program is different from the
local-mac-address property.
+ $ref: /schemas/types.yaml#definitions/uint8-array
+ items:
+ - minItems: 6
+ maxItems: 6
max-frame-size:
$ref: /schemas/types.yaml#definitions/uint32
is used for components that can have configurable fifo sizes.
managed:
- allOf:
- - $ref: /schemas/types.yaml#definitions/string
- - default: auto
- enum:
- - auto
- - in-band-status
description:
Specifies the PHY management type. If auto is set and fixed-link
is not specified, it uses MDIO for management.
+ $ref: /schemas/types.yaml#definitions/string
+ default: auto
+ enum:
+ - auto
+ - in-band-status
fixed-link:
allOf:
then:
properties:
speed:
- allOf:
- - $ref: /schemas/types.yaml#definitions/uint32
- - enum: [10, 100, 1000]
description:
Link speed.
+ $ref: /schemas/types.yaml#definitions/uint32
+ enum: [10, 100, 1000]
full-duplex:
$ref: /schemas/types.yaml#definitions/flag
properties:
qca,clk-out-frequency:
description: Clock output frequency in Hertz.
- allOf:
- - $ref: /schemas/types.yaml#/definitions/uint32
- - enum: [ 25000000, 50000000, 62500000, 125000000 ]
+ $ref: /schemas/types.yaml#/definitions/uint32
+ enum: [25000000, 50000000, 62500000, 125000000]
qca,clk-out-strength:
description: Clock output driver strength.
- allOf:
- - $ref: /schemas/types.yaml#/definitions/uint32
- - enum: [ 0, 1, 2 ]
+ $ref: /schemas/types.yaml#/definitions/uint32
+ enum: [0, 1, 2]
qca,keep-pll-enabled:
description: |
type: object
description:
Initial data for the VDDIO regulator. Set this to 1.5V or 1.8V.
- allOf:
- - $ref: /schemas/regulator/regulator.yaml
+ $ref: /schemas/regulator/regulator.yaml
vddh-regulator:
type: object
description:
Dummy subnode to model the external connection of the PHY VDDH
regulator to VDDIO.
- allOf:
- - $ref: /schemas/regulator/regulator.yaml
-
+ $ref: /schemas/regulator/regulator.yaml
examples:
- |
- const: config
qcom,smem-states:
- allOf:
- - $ref: /schemas/types.yaml#/definitions/phandle-array
+ $ref: /schemas/types.yaml#/definitions/phandle-array
description: State bits used in by the AP to signal the modem.
items:
- description: Whether the "ipa-clock-enabled" state bit is valid
- description: Whether the IPA clock is enabled (if valid)
qcom,smem-state-names:
- allOf:
- - $ref: /schemas/types.yaml#/definitions/string-array
+ $ref: /schemas/types.yaml#/definitions/string-array
description: The names of the state bits used for SMP2P output
items:
- const: ipa-clock-enabled-valid
snps,reset-delays-us:
deprecated: true
- allOf:
- - $ref: /schemas/types.yaml#definitions/uint32-array
- - minItems: 3
- maxItems: 3
description:
Triplet of delays. The 1st cell is reset pre-delay in micro
seconds. The 2nd cell is reset pulse in micro seconds. The 3rd
cell is reset post-delay in micro seconds.
+ $ref: /schemas/types.yaml#definitions/uint32-array
+ minItems: 3
+ maxItems: 3
snps,aal:
$ref: /schemas/types.yaml#definitions/flag
then:
properties:
snps,pbl:
- allOf:
- - $ref: /schemas/types.yaml#definitions/uint32
- - enum: [2, 4, 8]
description:
Programmable Burst Length (tx and rx)
+ $ref: /schemas/types.yaml#definitions/uint32
+ enum: [2, 4, 8]
snps,txpbl:
- allOf:
- - $ref: /schemas/types.yaml#definitions/uint32
- - enum: [2, 4, 8]
description:
Tx Programmable Burst Length. If set, DMA tx will use this
value rather than snps,pbl.
+ $ref: /schemas/types.yaml#definitions/uint32
+ enum: [2, 4, 8]
snps,rxpbl:
- allOf:
- - $ref: /schemas/types.yaml#definitions/uint32
- - enum: [2, 4, 8]
description:
Rx Programmable Burst Length. If set, DMA rx will use this
value rather than snps,pbl.
+ $ref: /schemas/types.yaml#definitions/uint32
+ enum: [2, 4, 8]
snps,no-pbl-x8:
$ref: /schemas/types.yaml#definitions/flag
- eth-ck
st,syscon:
- allOf:
- - $ref: "/schemas/types.yaml#/definitions/phandle-array"
+ $ref: "/schemas/types.yaml#/definitions/phandle-array"
description:
Should be phandle/offset pair. The phandle to the syscon node which
encompases the glue register, and the offset of the control register
description: label associated with this port
ti,dual-emac-pvid:
- allOf:
- - $ref: /schemas/types.yaml#/definitions/uint32
+ $ref: /schemas/types.yaml#/definitions/uint32
minimum: 1
maximum: 1024
description:
patternProperties:
"^mdio@":
type: object
- allOf:
- - $ref: "ti,davinci-mdio.yaml#"
description:
CPSW MDIO bus.
+ $ref: "ti,davinci-mdio.yaml#"
required:
ti,hwmods:
description: TI hwmod name
deprecated: true
- allOf:
- - $ref: /schemas/types.yaml#/definitions/string-array
- - items:
- const: davinci_mdio
+ $ref: /schemas/types.yaml#/definitions/string-array
+ items:
+ const: davinci_mdio
if:
properties:
type: object
description: CPSW2G NUSS external ports
- allOf:
- - $ref: ethernet-controller.yaml#
+ $ref: ethernet-controller.yaml#
properties:
reg:
patternProperties:
"^mdio@[0-9a-f]+$":
type: object
- allOf:
- - $ref: "ti,davinci-mdio.yaml#"
+ $ref: "ti,davinci-mdio.yaml#"
+
description:
CPSW MDIO bus.
description:
Set into the no BAR match register to configure the number of least
significant bits kept during inbound (PCIe -> AXI) address translations
- allOf:
- - $ref: /schemas/types.yaml#/definitions/uint32
+ $ref: /schemas/types.yaml#/definitions/uint32
minimum: 0
maximum: 64
default: 32
properties:
cdns,max-outbound-regions:
description: maximum number of outbound regions
- allOf:
- - $ref: /schemas/types.yaml#/definitions/uint32
+ $ref: /schemas/types.yaml#/definitions/uint32
minimum: 1
maximum: 32
default: 32
max-link-speed:
description: Specify PCI Gen for link capability.
- allOf:
- - $ref: /schemas/types.yaml#/definitions/uint32
- - enum: [ 1, 2, 3, 4 ]
- - default: 1
+ $ref: /schemas/types.yaml#/definitions/uint32
+ enum: [1, 2, 3, 4]
+ default: 1
bus-range:
description: Range of bus numbers associated with this controller.
max-functions:
description: Maximum number of functions that can be configured
- allOf:
- - $ref: /schemas/types.yaml#/definitions/uint8
+ $ref: /schemas/types.yaml#/definitions/uint8
minimum: 1
default: 1
maximum: 255
max-link-speed:
- allOf:
- - $ref: /schemas/types.yaml#/definitions/uint32
+ $ref: /schemas/types.yaml#/definitions/uint32
enum: [ 1, 2, 3, 4 ]
num-lanes:
description: maximum number of lanes
- allOf:
- - $ref: /schemas/types.yaml#/definitions/uint32
+ $ref: /schemas/types.yaml#/definitions/uint32
minimum: 1
default: 1
maximum: 16
description:
Specifies the type of PHY for which the group of PHY lanes is used.
Refer include/dt-bindings/phy/phy.h. Constants from the header should be used.
- allOf:
- - $ref: /schemas/types.yaml#/definitions/uint32
- - enum: [1, 2, 3, 4, 5, 6]
+ $ref: /schemas/types.yaml#/definitions/uint32
+ enum: [1, 2, 3, 4, 5, 6]
cdns,num-lanes:
description:
Number of DisplayPort lanes.
- allOf:
- - $ref: /schemas/types.yaml#/definitions/uint32
- - enum: [1, 2, 4]
+ $ref: /schemas/types.yaml#/definitions/uint32
+ enum: [1, 2, 4]
default: 4
cdns,max-bit-rate:
description:
Maximum DisplayPort link bit rate to use, in Mbps
- allOf:
- - $ref: /schemas/types.yaml#/definitions/uint32
- - enum: [2160, 2430, 2700, 3240, 4320, 5400, 8100]
+ $ref: /schemas/types.yaml#/definitions/uint32
+ enum: [2160, 2430, 2700, 3240, 4320, 5400, 8100]
default: 8100
required:
It is a 6 bit value that specifies offset to be
added to PHY refgen RESCODE via IMP_CTRL1 register. It is a PHY
tuning parameter that may vary for different boards of same SOC.
- allOf:
- - $ref: /schemas/types.yaml#/definitions/uint32
- - minimum: 0
- maximum: 63
- default: 0
+ $ref: /schemas/types.yaml#/definitions/uint32
+ minimum: 0
+ maximum: 63
+ default: 0
qcom,bias-ctrl-value:
description:
It is a 6 bit value that specifies bias-ctrl-value. It is a PHY
tuning parameter that may vary for different boards of same SOC.
- allOf:
- - $ref: /schemas/types.yaml#/definitions/uint32
- - minimum: 0
- maximum: 63
- default: 32
+ $ref: /schemas/types.yaml#/definitions/uint32
+ minimum: 0
+ maximum: 63
+ default: 32
qcom,charge-ctrl-value:
- description:
+ description:
It is a 2 bit value that specifies charge-ctrl-value. It is a PHY
tuning parameter that may vary for different boards of same SOC.
- allOf:
- - $ref: /schemas/types.yaml#/definitions/uint32
- - minimum: 0
- maximum: 3
- default: 0
+ $ref: /schemas/types.yaml#/definitions/uint32
+ minimum: 0
+ maximum: 3
+ default: 0
qcom,hstx-trim-value:
description:
output current.
Possible range is - 15mA to 24mA (stepsize of 600 uA).
See dt-bindings/phy/phy-qcom-qusb2.h for applicable values.
- allOf:
- - $ref: /schemas/types.yaml#/definitions/uint32
- - minimum: 0
- maximum: 15
- default: 3
+ $ref: /schemas/types.yaml#/definitions/uint32
+ minimum: 0
+ maximum: 15
+ default: 3
qcom,preemphasis-level:
description:
It is a 2 bit value that specifies pre-emphasis level.
Possible range is 0 to 15% (stepsize of 5%).
See dt-bindings/phy/phy-qcom-qusb2.h for applicable values.
- allOf:
- - $ref: /schemas/types.yaml#/definitions/uint32
- - minimum: 0
- maximum: 3
- default: 0
+ $ref: /schemas/types.yaml#/definitions/uint32
+ minimum: 0
+ maximum: 3
+ default: 2
qcom,preemphasis-width:
description:
pre-emphasis (specified using qcom,preemphasis-level) must be in
effect. Duration could be half-bit of full-bit.
See dt-bindings/phy/phy-qcom-qusb2.h for applicable values.
- allOf:
- - $ref: /schemas/types.yaml#/definitions/uint32
- - minimum: 0
- maximum: 1
- default: 0
+ $ref: /schemas/types.yaml#/definitions/uint32
+ minimum: 0
+ maximum: 1
+ default: 0
qcom,hsdisc-trim-value:
description:
It is a 2 bit value tuning parameter that control disconnect
threshold and may vary for different boards of same SOC.
- allOf:
- - $ref: /schemas/types.yaml#/definitions/uint32
- - minimum: 0
- maximum: 3
- default: 1
+ $ref: /schemas/types.yaml#/definitions/uint32
+ minimum: 0
+ maximum: 3
+ default: 0
required:
- compatible
gpio-line-names: true
input-debounce:
- allOf:
- - $ref: /schemas/types.yaml#/definitions/uint32-array
- - minItems: 1
- maxItems: 5
description:
Debouncing periods in microseconds, one period per interrupt
bank found in the controller
+ $ref: /schemas/types.yaml#/definitions/uint32-array
+ minItems: 1
+ maxItems: 5
patternProperties:
# It's pretty scary, but the basic idea is that:
bias-pull-down: true
drive-strength:
- allOf:
- - $ref: /schemas/types.yaml#/definitions/uint32
- - enum: [ 10, 20, 30, 40 ]
+ $ref: /schemas/types.yaml#/definitions/uint32
+ enum: [10, 20, 30, 40]
required:
- pins
then:
patternProperties:
"^function|groups$":
- allOf:
- - $ref: "/schemas/types.yaml#/definitions/string"
- - enum: [ ACPI, ADC0, ADC1, ADC10, ADC11, ADC12, ADC13, ADC14,
- ADC15, ADC2, ADC3, ADC4, ADC5, ADC6, ADC7, ADC8, ADC9, BMCINT,
- DDCCLK, DDCDAT, EXTRST, FLACK, FLBUSY, FLWP, GPID, GPID0, GPID2,
- GPID4, GPID6, GPIE0, GPIE2, GPIE4, GPIE6, I2C10, I2C11, I2C12,
- I2C13, I2C14, I2C3, I2C4, I2C5, I2C6, I2C7, I2C8, I2C9, LPCPD,
- LPCPME, LPCRST, LPCSMI, MAC1LINK, MAC2LINK, MDIO1, MDIO2, NCTS1,
- NCTS2, NCTS3, NCTS4, NDCD1, NDCD2, NDCD3, NDCD4, NDSR1, NDSR2,
- NDSR3, NDSR4, NDTR1, NDTR2, NDTR3, NDTR4, NDTS4, NRI1, NRI2,
- NRI3, NRI4, NRTS1, NRTS2, NRTS3, OSCCLK, PWM0, PWM1, PWM2, PWM3,
- PWM4, PWM5, PWM6, PWM7, RGMII1, RGMII2, RMII1, RMII2, ROM16,
- ROM8, ROMCS1, ROMCS2, ROMCS3, ROMCS4, RXD1, RXD2, RXD3, RXD4,
- SALT1, SALT2, SALT3, SALT4, SD1, SD2, SGPMCK, SGPMI, SGPMLD,
- SGPMO, SGPSCK, SGPSI0, SGPSI1, SGPSLD, SIOONCTRL, SIOPBI, SIOPBO,
- SIOPWREQ, SIOPWRGD, SIOS3, SIOS5, SIOSCI, SPI1, SPI1DEBUG,
- SPI1PASSTHRU, SPICS1, TIMER3, TIMER4, TIMER5, TIMER6, TIMER7,
- TIMER8, TXD1, TXD2, TXD3, TXD4, UART6, USB11D1, USB11H2, USB2D1,
- USB2H1, USBCKI, VGABIOS_ROM, VGAHS, VGAVS, VPI18, VPI24, VPI30,
- VPO12, VPO24, WDTRST1, WDTRST2 ]
+ $ref: "/schemas/types.yaml#/definitions/string"
+ enum: [ACPI, ADC0, ADC1, ADC10, ADC11, ADC12, ADC13, ADC14, ADC15,
+ ADC2, ADC3, ADC4, ADC5, ADC6, ADC7, ADC8, ADC9, BMCINT, DDCCLK, DDCDAT,
+ EXTRST, FLACK, FLBUSY, FLWP, GPID, GPID0, GPID2, GPID4, GPID6, GPIE0,
+ GPIE2, GPIE4, GPIE6, I2C10, I2C11, I2C12, I2C13, I2C14, I2C3, I2C4,
+ I2C5, I2C6, I2C7, I2C8, I2C9, LPCPD, LPCPME, LPCRST, LPCSMI, MAC1LINK,
+ MAC2LINK, MDIO1, MDIO2, NCTS1, NCTS2, NCTS3, NCTS4, NDCD1, NDCD2,
+ NDCD3, NDCD4, NDSR1, NDSR2, NDSR3, NDSR4, NDTR1, NDTR2, NDTR3, NDTR4,
+ NDTS4, NRI1, NRI2, NRI3, NRI4, NRTS1, NRTS2, NRTS3, OSCCLK, PWM0,
+ PWM1, PWM2, PWM3, PWM4, PWM5, PWM6, PWM7, RGMII1, RGMII2, RMII1,
+ RMII2, ROM16, ROM8, ROMCS1, ROMCS2, ROMCS3, ROMCS4, RXD1, RXD2, RXD3,
+ RXD4, SALT1, SALT2, SALT3, SALT4, SD1, SD2, SGPMCK, SGPMI, SGPMLD,
+ SGPMO, SGPSCK, SGPSI0, SGPSI1, SGPSLD, SIOONCTRL, SIOPBI, SIOPBO,
+ SIOPWREQ, SIOPWRGD, SIOS3, SIOS5, SIOSCI, SPI1, SPI1DEBUG, SPI1PASSTHRU,
+ SPICS1, TIMER3, TIMER4, TIMER5, TIMER6, TIMER7, TIMER8, TXD1, TXD2,
+ TXD3, TXD4, UART6, USB11D1, USB11H2, USB2D1, USB2H1, USBCKI, VGABIOS_ROM,
+ VGAHS, VGAVS, VPI18, VPI24, VPI30, VPO12, VPO24, WDTRST1, WDTRST2]
required:
- compatible
aspeed,external-nodes:
minItems: 2
maxItems: 2
- allOf:
- - $ref: /schemas/types.yaml#/definitions/phandle-array
+ $ref: /schemas/types.yaml#/definitions/phandle-array
description: |
A cell of phandles to external controller nodes:
0: compatible with "aspeed,ast2500-gfx", "syscon"
then:
patternProperties:
"^function|groups$":
- allOf:
- - $ref: "/schemas/types.yaml#/definitions/string"
- - enum: [ ACPI, ADC0, ADC1, ADC10, ADC11, ADC12, ADC13, ADC14,
- ADC15, ADC2, ADC3, ADC4, ADC5, ADC6, ADC7, ADC8, ADC9, BMCINT,
- DDCCLK, DDCDAT, ESPI, FWSPICS1, FWSPICS2, GPID0, GPID2, GPID4,
- GPID6, GPIE0, GPIE2, GPIE4, GPIE6, I2C10, I2C11, I2C12, I2C13,
- I2C14, I2C3, I2C4, I2C5, I2C6, I2C7, I2C8, I2C9, LAD0, LAD1,
- LAD2, LAD3, LCLK, LFRAME, LPCHC, LPCPD, LPCPLUS, LPCPME, LPCRST,
- LPCSMI, LSIRQ, MAC1LINK, MAC2LINK, MDIO1, MDIO2, NCTS1, NCTS2,
- NCTS3, NCTS4, NDCD1, NDCD2, NDCD3, NDCD4, NDSR1, NDSR2, NDSR3,
- NDSR4, NDTR1, NDTR2, NDTR3, NDTR4, NRI1, NRI2, NRI3, NRI4, NRTS1,
- NRTS2, NRTS3, NRTS4, OSCCLK, PEWAKE, PNOR, PWM0, PWM1, PWM2,
- PWM3, PWM4, PWM5, PWM6, PWM7, RGMII1, RGMII2, RMII1, RMII2, RXD1,
- RXD2, RXD3, RXD4, SALT1, SALT10, SALT11, SALT12, SALT13, SALT14,
- SALT2, SALT3, SALT4, SALT5, SALT6, SALT7, SALT8, SALT9, SCL1,
- SCL2, SD1, SD2, SDA1, SDA2, SGPS1, SGPS2, SIOONCTRL, SIOPBI,
- SIOPBO, SIOPWREQ, SIOPWRGD, SIOS3, SIOS5, SIOSCI, SPI1, SPI1CS1,
- SPI1DEBUG, SPI1PASSTHRU, SPI2CK, SPI2CS0, SPI2CS1, SPI2MISO,
- SPI2MOSI, TIMER3, TIMER4, TIMER5, TIMER6, TIMER7, TIMER8, TXD1,
- TXD2, TXD3, TXD4, UART6, USB11BHID, USB2AD, USB2AH, USB2BD,
- USB2BH, USBCKI, VGABIOSROM, VGAHS, VGAVS, VPI24, VPO, WDTRST1,
- WDTRST2, ]
+ $ref: "/schemas/types.yaml#/definitions/string"
+ enum: [ACPI, ADC0, ADC1, ADC10, ADC11, ADC12, ADC13, ADC14, ADC15,
+ ADC2, ADC3, ADC4, ADC5, ADC6, ADC7, ADC8, ADC9, BMCINT, DDCCLK, DDCDAT,
+ ESPI, FWSPICS1, FWSPICS2, GPID0, GPID2, GPID4, GPID6, GPIE0, GPIE2,
+ GPIE4, GPIE6, I2C10, I2C11, I2C12, I2C13, I2C14, I2C3, I2C4, I2C5,
+ I2C6, I2C7, I2C8, I2C9, LAD0, LAD1, LAD2, LAD3, LCLK, LFRAME, LPCHC,
+ LPCPD, LPCPLUS, LPCPME, LPCRST, LPCSMI, LSIRQ, MAC1LINK, MAC2LINK,
+ MDIO1, MDIO2, NCTS1, NCTS2, NCTS3, NCTS4, NDCD1, NDCD2, NDCD3, NDCD4,
+ NDSR1, NDSR2, NDSR3, NDSR4, NDTR1, NDTR2, NDTR3, NDTR4, NRI1, NRI2,
+ NRI3, NRI4, NRTS1, NRTS2, NRTS3, NRTS4, OSCCLK, PEWAKE, PNOR, PWM0,
+ PWM1, PWM2, PWM3, PWM4, PWM5, PWM6, PWM7, RGMII1, RGMII2, RMII1,
+ RMII2, RXD1, RXD2, RXD3, RXD4, SALT1, SALT10, SALT11, SALT12, SALT13,
+ SALT14, SALT2, SALT3, SALT4, SALT5, SALT6, SALT7, SALT8, SALT9, SCL1,
+ SCL2, SD1, SD2, SDA1, SDA2, SGPS1, SGPS2, SIOONCTRL, SIOPBI, SIOPBO,
+ SIOPWREQ, SIOPWRGD, SIOS3, SIOS5, SIOSCI, SPI1, SPI1CS1, SPI1DEBUG,
+ SPI1PASSTHRU, SPI2CK, SPI2CS0, SPI2CS1, SPI2MISO, SPI2MOSI, TIMER3,
+ TIMER4, TIMER5, TIMER6, TIMER7, TIMER8, TXD1, TXD2, TXD3, TXD4, UART6,
+ USB11BHID, USB2AD, USB2AH, USB2BD, USB2BH, USBCKI, VGABIOSROM, VGAHS,
+ VGAVS, VPI24, VPO, WDTRST1, WDTRST2]
required:
- compatible
then:
properties:
function:
- allOf:
- - $ref: "/schemas/types.yaml#/definitions/string"
- - enum: [ ADC0, ADC1, ADC10, ADC11, ADC12, ADC13, ADC14, ADC15,
- ADC2, ADC3, ADC4, ADC5, ADC6, ADC7, ADC8, ADC9, BMCINT, EMMC,
- ESPI, ESPIALT, FSI1, FSI2, FWSPIABR, FWSPID, FWSPIWP, GPIT0,
- GPIT1, GPIT2, GPIT3, GPIT4, GPIT5, GPIT6, GPIT7, GPIU0, GPIU1,
- GPIU2, GPIU3, GPIU4, GPIU5, GPIU6, GPIU7, I2C1, I2C10, I2C11,
- I2C12, I2C13, I2C14, I2C15, I2C16, I2C2, I2C3, I2C4, I2C5, I2C6,
- I2C7, I2C8, I2C9, I3C3, I3C4, I3C5, I3C6, JTAGM, LHPD, LHSIRQ,
- LPC, LPCHC, LPCPD, LPCPME, LPCSMI, LSIRQ, MACLINK1, MACLINK2,
- MACLINK3, MACLINK4, MDIO1, MDIO2, MDIO3, MDIO4, NCTS1, NCTS2,
- NCTS3, NCTS4, NDCD1, NDCD2, NDCD3, NDCD4, NDSR1, NDSR2, NDSR3,
- NDSR4, NDTR1, NDTR2, NDTR3, NDTR4, NRI1, NRI2, NRI3, NRI4, NRTS1,
- NRTS2, NRTS3, NRTS4, OSCCLK, PEWAKE, PWM0, PWM1, PWM10, PWM11,
- PWM12, PWM13, PWM14, PWM15, PWM2, PWM3, PWM4, PWM5, PWM6, PWM7,
- PWM8, PWM9, RGMII1, RGMII2, RGMII3, RGMII4, RMII1, RMII2, RMII3,
- RMII4, RXD1, RXD2, RXD3, RXD4, SALT1, SALT10, SALT11, SALT12,
- SALT13, SALT14, SALT15, SALT16, SALT2, SALT3, SALT4, SALT5,
- SALT6, SALT7, SALT8, SALT9, SD1, SD2, SGPM1, SGPS1, SIOONCTRL,
- SIOPBI, SIOPBO, SIOPWREQ, SIOPWRGD, SIOS3, SIOS5, SIOSCI, SPI1,
- SPI1ABR, SPI1CS1, SPI1WP, SPI2, SPI2CS1, SPI2CS2, TACH0, TACH1,
- TACH10, TACH11, TACH12, TACH13, TACH14, TACH15, TACH2, TACH3,
- TACH4, TACH5, TACH6, TACH7, TACH8, TACH9, THRU0, THRU1, THRU2,
- THRU3, TXD1, TXD2, TXD3, TXD4, UART10, UART11, UART12, UART13,
- UART6, UART7, UART8, UART9, USBAD, USBADP, USB2AH, USB2AHP,
- USB2BD, USB2BH, VB, VGAHS, VGAVS, WDTRST1, WDTRST2, WDTRST3,
- WDTRST4, ]
+ $ref: "/schemas/types.yaml#/definitions/string"
+ enum: [ADC0, ADC1, ADC10, ADC11, ADC12, ADC13, ADC14, ADC15, ADC2,
+ ADC3, ADC4, ADC5, ADC6, ADC7, ADC8, ADC9, BMCINT, EMMC, ESPI, ESPIALT,
+ FSI1, FSI2, FWSPIABR, FWSPID, FWSPIWP, GPIT0, GPIT1, GPIT2, GPIT3,
+ GPIT4, GPIT5, GPIT6, GPIT7, GPIU0, GPIU1, GPIU2, GPIU3, GPIU4, GPIU5,
+ GPIU6, GPIU7, I2C1, I2C10, I2C11, I2C12, I2C13, I2C14, I2C15, I2C16,
+ I2C2, I2C3, I2C4, I2C5, I2C6, I2C7, I2C8, I2C9, I3C3, I3C4, I3C5,
+ I3C6, JTAGM, LHPD, LHSIRQ, LPC, LPCHC, LPCPD, LPCPME, LPCSMI, LSIRQ,
+ MACLINK1, MACLINK2, MACLINK3, MACLINK4, MDIO1, MDIO2, MDIO3, MDIO4,
+ NCTS1, NCTS2, NCTS3, NCTS4, NDCD1, NDCD2, NDCD3, NDCD4, NDSR1, NDSR2,
+ NDSR3, NDSR4, NDTR1, NDTR2, NDTR3, NDTR4, NRI1, NRI2, NRI3, NRI4,
+ NRTS1, NRTS2, NRTS3, NRTS4, OSCCLK, PEWAKE, PWM0, PWM1, PWM10, PWM11,
+ PWM12, PWM13, PWM14, PWM15, PWM2, PWM3, PWM4, PWM5, PWM6, PWM7, PWM8,
+ PWM9, RGMII1, RGMII2, RGMII3, RGMII4, RMII1, RMII2, RMII3, RMII4,
+ RXD1, RXD2, RXD3, RXD4, SALT1, SALT10, SALT11, SALT12, SALT13, SALT14,
+ SALT15, SALT16, SALT2, SALT3, SALT4, SALT5, SALT6, SALT7, SALT8,
+ SALT9, SD1, SD2, SGPM1, SGPS1, SIOONCTRL, SIOPBI, SIOPBO, SIOPWREQ,
+ SIOPWRGD, SIOS3, SIOS5, SIOSCI, SPI1, SPI1ABR, SPI1CS1, SPI1WP, SPI2,
+ SPI2CS1, SPI2CS2, TACH0, TACH1, TACH10, TACH11, TACH12, TACH13, TACH14,
+ TACH15, TACH2, TACH3, TACH4, TACH5, TACH6, TACH7, TACH8, TACH9, THRU0,
+ THRU1, THRU2, THRU3, TXD1, TXD2, TXD3, TXD4, UART10, UART11, UART12,
+ UART13, UART6, UART7, UART8, UART9, USBAD, USBADP, USB2AH, USB2AHP,
+ USB2BD, USB2BH, VB, VGAHS, VGAVS, WDTRST1, WDTRST2, WDTRST3, WDTRST4]
+
groups:
- allOf:
- - $ref: "/schemas/types.yaml#/definitions/string"
- - enum: [ ADC0, ADC1, ADC10, ADC11, ADC12, ADC13, ADC14, ADC15,
- ADC2, ADC3, ADC4, ADC5, ADC6, ADC7, ADC8, ADC9, BMCINT, EMMCG1,
- EMMCG4, EMMCG8, ESPI, ESPIALT, FSI1, FSI2, FWSPIABR, FWSPID,
- FWQSPID, FWSPIWP, GPIT0, GPIT1, GPIT2, GPIT3, GPIT4, GPIT5,
- GPIT6, GPIT7, GPIU0, GPIU1, GPIU2, GPIU3, GPIU4, GPIU5, GPIU6,
- GPIU7, HVI3C3, HVI3C4, I2C1, I2C10, I2C11, I2C12, I2C13, I2C14,
- I2C15, I2C16, I2C2, I2C3, I2C4, I2C5, I2C6, I2C7, I2C8, I2C9,
- I3C3, I3C4, I3C5, I3C6, JTAGM, LHPD, LHSIRQ, LPC, LPCHC, LPCPD,
- LPCPME, LPCSMI, LSIRQ, MACLINK1, MACLINK2, MACLINK3, MACLINK4,
- MDIO1, MDIO2, MDIO3, MDIO4, NCTS1, NCTS2, NCTS3, NCTS4, NDCD1,
- NDCD2, NDCD3, NDCD4, NDSR1, NDSR2, NDSR3, NDSR4, NDTR1, NDTR2,
- NDTR3, NDTR4, NRI1, NRI2, NRI3, NRI4, NRTS1, NRTS2, NRTS3, NRTS4,
- OSCCLK, PEWAKE, PWM0, PWM1, PWM10G0, PWM10G1, PWM11G0, PWM11G1,
- PWM12G0, PWM12G1, PWM13G0, PWM13G1, PWM14G0, PWM14G1, PWM15G0,
- PWM15G1, PWM2, PWM3, PWM4, PWM5, PWM6, PWM7, PWM8G0, PWM8G1,
- PWM9G0, PWM9G1, QSPI1, QSPI2, RGMII1, RGMII2, RGMII3, RGMII4,
- RMII1, RMII2, RMII3, RMII4, RXD1, RXD2, RXD3, RXD4, SALT1,
- SALT10G0, SALT10G1, SALT11G0, SALT11G1, SALT12G0, SALT12G1,
- SALT13G0, SALT13G1, SALT14G0, SALT14G1, SALT15G0, SALT15G1,
- SALT16G0, SALT16G1, SALT2, SALT3, SALT4, SALT5, SALT6, SALT7,
- SALT8, SALT9G0, SALT9G1, SD1, SD2, SD3, SGPM1, SGPS1, SIOONCTRL,
- SIOPBI, SIOPBO, SIOPWREQ, SIOPWRGD, SIOS3, SIOS5, SIOSCI, SPI1,
- SPI1ABR, SPI1CS1, SPI1WP, SPI2, SPI2CS1, SPI2CS2, TACH0, TACH1,
- TACH10, TACH11, TACH12, TACH13, TACH14, TACH15, TACH2, TACH3,
- TACH4, TACH5, TACH6, TACH7, TACH8, TACH9, THRU0, THRU1, THRU2,
- THRU3, TXD1, TXD2, TXD3, TXD4, UART10, UART11, UART12G0,
- UART12G1, UART13G0, UART13G1, UART6, UART7, UART8, UART9, USBA,
- USBB, VB, VGAHS, VGAVS, WDTRST1, WDTRST2, WDTRST3, WDTRST4, ]
+ $ref: "/schemas/types.yaml#/definitions/string"
+ enum: [ADC0, ADC1, ADC10, ADC11, ADC12, ADC13, ADC14, ADC15, ADC2,
+ ADC3, ADC4, ADC5, ADC6, ADC7, ADC8, ADC9, BMCINT, EMMCG1, EMMCG4,
+ EMMCG8, ESPI, ESPIALT, FSI1, FSI2, FWSPIABR, FWSPID, FWQSPID, FWSPIWP,
+ GPIT0, GPIT1, GPIT2, GPIT3, GPIT4, GPIT5, GPIT6, GPIT7, GPIU0, GPIU1,
+ GPIU2, GPIU3, GPIU4, GPIU5, GPIU6, GPIU7, HVI3C3, HVI3C4, I2C1, I2C10,
+ I2C11, I2C12, I2C13, I2C14, I2C15, I2C16, I2C2, I2C3, I2C4, I2C5,
+ I2C6, I2C7, I2C8, I2C9, I3C3, I3C4, I3C5, I3C6, JTAGM, LHPD, LHSIRQ,
+ LPC, LPCHC, LPCPD, LPCPME, LPCSMI, LSIRQ, MACLINK1, MACLINK2, MACLINK3,
+ MACLINK4, MDIO1, MDIO2, MDIO3, MDIO4, NCTS1, NCTS2, NCTS3, NCTS4,
+ NDCD1, NDCD2, NDCD3, NDCD4, NDSR1, NDSR2, NDSR3, NDSR4, NDTR1, NDTR2,
+ NDTR3, NDTR4, NRI1, NRI2, NRI3, NRI4, NRTS1, NRTS2, NRTS3, NRTS4,
+ OSCCLK, PEWAKE, PWM0, PWM1, PWM10G0, PWM10G1, PWM11G0, PWM11G1, PWM12G0,
+ PWM12G1, PWM13G0, PWM13G1, PWM14G0, PWM14G1, PWM15G0, PWM15G1, PWM2,
+ PWM3, PWM4, PWM5, PWM6, PWM7, PWM8G0, PWM8G1, PWM9G0, PWM9G1, QSPI1,
+ QSPI2, RGMII1, RGMII2, RGMII3, RGMII4, RMII1, RMII2, RMII3, RMII4,
+ RXD1, RXD2, RXD3, RXD4, SALT1, SALT10G0, SALT10G1, SALT11G0, SALT11G1,
+ SALT12G0, SALT12G1, SALT13G0, SALT13G1, SALT14G0, SALT14G1, SALT15G0,
+ SALT15G1, SALT16G0, SALT16G1, SALT2, SALT3, SALT4, SALT5, SALT6,
+ SALT7, SALT8, SALT9G0, SALT9G1, SD1, SD2, SD3, SGPM1, SGPS1, SIOONCTRL,
+ SIOPBI, SIOPBO, SIOPWREQ, SIOPWRGD, SIOS3, SIOS5, SIOSCI, SPI1, SPI1ABR,
+ SPI1CS1, SPI1WP, SPI2, SPI2CS1, SPI2CS2, TACH0, TACH1, TACH10, TACH11,
+ TACH12, TACH13, TACH14, TACH15, TACH2, TACH3, TACH4, TACH5, TACH6,
+ TACH7, TACH8, TACH9, THRU0, THRU1, THRU2, THRU3, TXD1, TXD2, TXD3,
+ TXD4, UART10, UART11, UART12G0, UART12G1, UART13G0, UART13G1, UART6,
+ UART7, UART8, UART9, USBA, USBB, VB, VGAHS, VGAVS, WDTRST1, WDTRST2,
+ WDTRST3, WDTRST4]
required:
- compatible
be found in <arch/arm64/boot/dts/freescale/imx8mm-pinfunc.h>. The last
integer CONFIG is the pad setting value like pull-up on this pin. Please
refer to i.MX8M Mini Reference Manual for detailed CONFIG settings.
- allOf:
- - $ref: /schemas/types.yaml#/definitions/uint32-matrix
- - items:
- items:
- - description: |
- "mux_reg" indicates the offset of mux register.
- - description: |
- "conf_reg" indicates the offset of pad configuration register.
- - description: |
- "input_reg" indicates the offset of select input register.
- - description: |
- "mux_val" indicates the mux value to be applied.
- - description: |
- "input_val" indicates the select input value to be applied.
- - description: |
- "pad_setting" indicates the pad configuration value to be applied.
+ $ref: /schemas/types.yaml#/definitions/uint32-matrix
+ items:
+ items:
+ - description: |
+ "mux_reg" indicates the offset of mux register.
+ - description: |
+ "conf_reg" indicates the offset of pad configuration register.
+ - description: |
+ "input_reg" indicates the offset of select input register.
+ - description: |
+ "mux_val" indicates the mux value to be applied.
+ - description: |
+ "input_val" indicates the select input value to be applied.
+ - description: |
+ "pad_setting" indicates the pad configuration value to be applied.
required:
- fsl,pins
be found in <arch/arm64/boot/dts/freescale/imx8mn-pinfunc.h>. The last
integer CONFIG is the pad setting value like pull-up on this pin. Please
refer to i.MX8M Nano Reference Manual for detailed CONFIG settings.
- allOf:
- - $ref: /schemas/types.yaml#/definitions/uint32-matrix
- - items:
- items:
- - description: |
- "mux_reg" indicates the offset of mux register.
- - description: |
- "conf_reg" indicates the offset of pad configuration register.
- - description: |
- "input_reg" indicates the offset of select input register.
- - description: |
- "mux_val" indicates the mux value to be applied.
- - description: |
- "input_val" indicates the select input value to be applied.
- - description: |
- "pad_setting" indicates the pad configuration value to be applied.
+ $ref: /schemas/types.yaml#/definitions/uint32-matrix
+ items:
+ items:
+ - description: |
+ "mux_reg" indicates the offset of mux register.
+ - description: |
+ "conf_reg" indicates the offset of pad configuration register.
+ - description: |
+ "input_reg" indicates the offset of select input register.
+ - description: |
+ "mux_val" indicates the mux value to be applied.
+ - description: |
+ "input_val" indicates the select input value to be applied.
+ - description: |
+ "pad_setting" indicates the pad configuration value to be applied.
required:
- fsl,pins
be found in <arch/arm64/boot/dts/freescale/imx8mp-pinfunc.h>. The last
integer CONFIG is the pad setting value like pull-up on this pin. Please
refer to i.MX8M Plus Reference Manual for detailed CONFIG settings.
- allOf:
- - $ref: /schemas/types.yaml#/definitions/uint32-matrix
- - items:
- items:
- - description: |
- "mux_reg" indicates the offset of mux register.
- - description: |
- "conf_reg" indicates the offset of pad configuration register.
- - description: |
- "input_reg" indicates the offset of select input register.
- - description: |
- "mux_val" indicates the mux value to be applied.
- - description: |
- "input_val" indicates the select input value to be applied.
- - description: |
- "pad_setting" indicates the pad configuration value to be applied.
+ $ref: /schemas/types.yaml#/definitions/uint32-matrix
+ items:
+ items:
+ - description: |
+ "mux_reg" indicates the offset of mux register.
+ - description: |
+ "conf_reg" indicates the offset of pad configuration register.
+ - description: |
+ "input_reg" indicates the offset of select input register.
+ - description: |
+ "mux_val" indicates the mux value to be applied.
+ - description: |
+ "input_val" indicates the select input value to be applied.
+ - description: |
+ "pad_setting" indicates the pad configuration value to be applied.
required:
- fsl,pins
be found in <arch/arm64/boot/dts/freescale/imx8mq-pinfunc.h>. The last
integer CONFIG is the pad setting value like pull-up on this pin. Please
refer to i.MX8M Quad Reference Manual for detailed CONFIG settings.
- allOf:
- - $ref: /schemas/types.yaml#/definitions/uint32-matrix
- - items:
- items:
- - description: |
- "mux_reg" indicates the offset of mux register.
- - description: |
- "conf_reg" indicates the offset of pad configuration register.
- - description: |
- "input_reg" indicates the offset of select input register.
- - description: |
- "mux_val" indicates the mux value to be applied.
- - description: |
- "input_val" indicates the select input value to be applied.
- - description: |
- "pad_setting" indicates the pad configuration value to be applied.
+ $ref: /schemas/types.yaml#/definitions/uint32-matrix
+ items:
+ items:
+ - description: |
+ "mux_reg" indicates the offset of mux register.
+ - description: |
+ "conf_reg" indicates the offset of pad configuration register.
+ - description: |
+ "input_reg" indicates the offset of select input register.
+ - description: |
+ "mux_val" indicates the mux value to be applied.
+ - description: |
+ "input_val" indicates the select input value to be applied.
+ - description: |
+ "pad_setting" indicates the pad configuration value to be applied.
required:
- fsl,pins
patternProperties:
'-pins$':
type: object
- allOf:
- - $ref: pincfg-node.yaml#
- - $ref: pinmux-node.yaml#
description:
Pinctrl node's client devices use subnodes for desired pin configuration.
Client device subnodes use below standard properties.
+ $ref: pinmux-node.yaml#
properties:
function: true
this, "pins" or "pinmux" has to be specified)
pinmux:
- allOf:
- - $ref: /schemas/types.yaml#/definitions/uint32-array
description:
The list of numeric pin ids and their mux settings that properties in the
node apply to (either this, "pins" or "groups" have to be specified)
+ $ref: /schemas/types.yaml#/definitions/uint32-array
pinctrl-pin-array:
$ref: /schemas/types.yaml#/definitions/uint32-array
description:
Pinctrl node's client devices use subnodes for desired pin configuration.
Client device subnodes use below standard properties.
- allOf:
- - $ref: "/schemas/pinctrl/pincfg-node.yaml"
+ $ref: "/schemas/pinctrl/pincfg-node.yaml"
properties:
pins:
hwlocks: true
st,syscfg:
- allOf:
- - $ref: "/schemas/types.yaml#/definitions/phandle-array"
description: Should be phandle/offset/mask
- Phandle to the syscon node which includes IRQ mux selection.
- The offset of the IRQ mux selection register.
- The field mask of IRQ mux, needed if different of 0xf.
+ $ref: "/schemas/types.yaml#/definitions/phandle-array"
st,package:
- allOf:
- - $ref: /schemas/types.yaml#/definitions/uint32
- - enum: [1, 2, 4, 8]
description:
Indicates the SOC package used.
More details in include/dt-bindings/pinctrl/stm32-pinfunc.h
-
+ $ref: /schemas/types.yaml#/definitions/uint32
+ enum: [1, 2, 4, 8]
patternProperties:
'^gpio@[0-9a-f]*$':
maximum: 16
st,bank-name:
- allOf:
- - $ref: "/schemas/types.yaml#/definitions/string"
- - enum:
- - GPIOA
- - GPIOB
- - GPIOC
- - GPIOD
- - GPIOE
- - GPIOF
- - GPIOG
- - GPIOH
- - GPIOI
- - GPIOJ
- - GPIOK
- - GPIOZ
description:
Should be a name string for this bank as specified in the datasheet.
+ $ref: "/schemas/types.yaml#/definitions/string"
+ enum:
+ - GPIOA
+ - GPIOB
+ - GPIOC
+ - GPIOD
+ - GPIOE
+ - GPIOF
+ - GPIOG
+ - GPIOH
+ - GPIOI
+ - GPIOJ
+ - GPIOK
+ - GPIOZ
st,bank-ioport:
- allOf:
- - $ref: "/schemas/types.yaml#/definitions/uint32"
- - minimum: 0
- - maximum: 11
-
description:
Should correspond to the EXTI IOport selection (EXTI line used
to select GPIOs as interrupts).
+ $ref: "/schemas/types.yaml#/definitions/uint32"
+ minimum: 0
+ maximum: 11
required:
- gpio-controller
configuration, pullups, drive, output high/low and output speed.
properties:
pinmux:
- allOf:
- - $ref: "/schemas/types.yaml#/definitions/uint32-array"
+ $ref: "/schemas/types.yaml#/definitions/uint32-array"
description: |
Integer array, represents gpio pin number and mux setting.
Supported pin number and mux varies for different SoCs, and are
1: Medium speed
2: Fast speed
3: High speed
- allOf:
- - $ref: /schemas/types.yaml#/definitions/uint32
- - enum: [0, 1, 2, 3]
+ $ref: /schemas/types.yaml#/definitions/uint32
+ enum: [0, 1, 2, 3]
required:
- pinmux
amlogic,ao-sysctrl:
description: phandle to the AO sysctrl node
- allOf:
- - $ref: /schemas/types.yaml#/definitions/phandle
+ $ref: /schemas/types.yaml#/definitions/phandle
required:
- compatible
A list of PWM channels used as PWM outputs on particular platform.
It is an array of up to 5 elements being indices of PWM channels
(from 0 to 4), the order does not matter.
- allOf:
- - $ref: /schemas/types.yaml#/definitions/uint32-array
- - uniqueItems: true
- - items:
- minimum: 0
- maximum: 4
+ $ref: /schemas/types.yaml#/definitions/uint32-array
+ uniqueItems: true
+ items:
+ minimum: 0
+ maximum: 4
required:
- clocks
0: LOW
1: HIGH
Default is LOW if nothing else is specified.
- allOf:
- - $ref: /schemas/types.yaml#/definitions/uint32-array
- - maxItems: 8
- items:
- enum: [ 0, 1 ]
- default: 0
+ $ref: /schemas/types.yaml#/definitions/uint32-array
+ maxItems: 8
+ items:
+ enum: [0, 1]
+ default: 0
states:
description: Selection of available voltages/currents provided by this
regulator and matching GPIO configurations to achieve them. If there are
no states in the "states" array, use a fixed regulator instead.
- allOf:
- - $ref: /schemas/types.yaml#/definitions/uint32-matrix
- - maxItems: 8
- items:
- items:
- - description: Voltage in microvolts
- - description: GPIO group state value
+ $ref: /schemas/types.yaml#/definitions/uint32-matrix
+ maxItems: 8
+ items:
+ items:
+ - description: Voltage in microvolts
+ - description: GPIO group state value
startup-delay-us:
description: startup time in microseconds
regulator-type:
description: Specifies what is being regulated.
- allOf:
- - $ref: /schemas/types.yaml#/definitions/string
- - enum:
- - voltage
- - current
- default: voltage
+ $ref: /schemas/types.yaml#/definitions/string
+ enum:
+ - voltage
+ - current
+ default: voltage
required:
- compatible
patternProperties:
"^buck[1-4]$":
- allOf:
- - $ref: "regulator.yaml#"
+ $ref: "regulator.yaml#"
type: object
"^ldo[1-4]$":
- allOf:
- - $ref: "regulator.yaml#"
+ $ref: "regulator.yaml#"
type: object
additionalProperties: false
regulators:
type: object
- allOf:
- - $ref: regulator.yaml#
+ $ref: regulator.yaml#
+
description: |
list of regulators provided by this controller, must be named
after their hardware counterparts BUCK[1-4], one LDORTC, and LDO[2-5]
properties:
mps,switch-freq:
- allOf:
- - $ref: "/schemas/types.yaml#/definitions/uint8"
- enum: [ 0, 1, 2, 3 ]
+ $ref: "/schemas/types.yaml#/definitions/uint8"
+ enum: [0, 1, 2, 3]
default: 2
description: |
switching frequency must be one of following corresponding value
patternProperties:
"^ldo[1-4]$":
type: object
- allOf:
- - $ref: regulator.yaml#
+ $ref: regulator.yaml#
"^ldortc$":
type: object
- allOf:
- - $ref: regulator.yaml#
+ $ref: regulator.yaml#
"^buck[1-4]$":
type: object
- allOf:
- - $ref: regulator.yaml#
+ $ref: regulator.yaml#
properties:
mps,buck-softstart:
- allOf:
- - $ref: "/schemas/types.yaml#/definitions/uint8"
- enum: [ 0, 1, 2, 3 ]
+ $ref: "/schemas/types.yaml#/definitions/uint8"
+ enum: [0, 1, 2, 3]
description: |
defines the soft start time of this buck, must be one of the following
corresponding values 150us, 300us, 610us, 920us
mps,buck-phase-delay:
- allOf:
- - $ref: "/schemas/types.yaml#/definitions/uint8"
- enum: [ 0, 1, 2, 3 ]
+ $ref: "/schemas/types.yaml#/definitions/uint8"
+ enum: [0, 1, 2, 3]
description: |
defines the phase delay of this buck, must be one of the following
corresponding values 0deg, 90deg, 180deg, 270deg
0: Disable active discharge.
1: Enable active discharge.
Absence of this property will leave configuration to default.
- allOf:
- - $ref: "/schemas/types.yaml#/definitions/uint32"
- - enum: [ 0, 1 ]
+ $ref: "/schemas/types.yaml#/definitions/uint32"
+ enum: [0, 1]
regulator-coupled-with:
description: Regulators with which the regulator is coupled. The linkage
patternProperties:
"^LDO[1-7]$":
type: object
- allOf:
- - $ref: regulator.yaml#
description:
Properties for single LDO regulator.
+ $ref: regulator.yaml#
properties:
regulator-name:
"^BUCK[1-7]$":
type: object
- allOf:
- - $ref: regulator.yaml#
description:
Properties for single BUCK regulator.
+ $ref: regulator.yaml#
properties:
regulator-name:
should be "buck1", ..., "buck7"
rohm,dvs-run-voltage:
- allOf:
- - $ref: "/schemas/types.yaml#/definitions/uint32"
- - minimum: 0
- maximum: 3300000
description:
PMIC default "RUN" state voltage in uV. See below table for
bucks which support this. 0 means disabled.
+ $ref: "/schemas/types.yaml#/definitions/uint32"
+ minimum: 0
+ maximum: 3300000
rohm,dvs-idle-voltage:
- allOf:
- - $ref: "/schemas/types.yaml#/definitions/uint32"
- - minimum: 0
- maximum: 3300000
description:
PMIC default "IDLE" state voltage in uV. See below table for
bucks which support this. 0 means disabled.
+ $ref: "/schemas/types.yaml#/definitions/uint32"
+ minimum: 0
+ maximum: 3300000
rohm,dvs-suspend-voltage:
- allOf:
- - $ref: "/schemas/types.yaml#/definitions/uint32"
- - minimum: 0
- maximum: 3300000
description:
PMIC default "SUSPEND" state voltage in uV. See below table for
bucks which support this. 0 means disabled.
+ $ref: "/schemas/types.yaml#/definitions/uint32"
+ minimum: 0
+ maximum: 3300000
rohm,dvs-lpsr-voltage:
- allOf:
- - $ref: "/schemas/types.yaml#/definitions/uint32"
- - minimum: 0
- maximum: 3300000
description:
PMIC default "LPSR" state voltage in uV. See below table for
bucks which support this. 0 means disabled.
+ $ref: "/schemas/types.yaml#/definitions/uint32"
+ minimum: 0
+ maximum: 3300000
# Supported default DVS states:
# buck | run | idle | suspend | lpsr
patternProperties:
"^LDO[1-7]$":
type: object
- allOf:
- - $ref: regulator.yaml#
+ $ref: regulator.yaml#
description:
Properties for single LDO regulator.
"^BUCK[1-8]$":
type: object
- allOf:
- - $ref: regulator.yaml#
+ $ref: regulator.yaml#
description:
Properties for single BUCK regulator.
should be "buck1", ..., "buck8"
rohm,dvs-run-voltage:
- allOf:
- - $ref: "/schemas/types.yaml#/definitions/uint32"
- - minimum: 0
- maximum: 1300000
+ $ref: "/schemas/types.yaml#/definitions/uint32"
+ minimum: 0
+ maximum: 1300000
description:
PMIC default "RUN" state voltage in uV. See below table for
bucks which support this. 0 means disabled.
rohm,dvs-idle-voltage:
- allOf:
- - $ref: "/schemas/types.yaml#/definitions/uint32"
- - minimum: 0
- maximum: 1300000
+ $ref: "/schemas/types.yaml#/definitions/uint32"
+ minimum: 0
+ maximum: 1300000
description:
PMIC default "IDLE" state voltage in uV. See below table for
bucks which support this. 0 means disabled.
rohm,dvs-suspend-voltage:
- allOf:
- - $ref: "/schemas/types.yaml#/definitions/uint32"
- - minimum: 0
- maximum: 1300000
+ $ref: "/schemas/types.yaml#/definitions/uint32"
+ minimum: 0
+ maximum: 1300000
description:
PMIC default "SUSPEND" state voltage in uV. See below table for
bucks which support this. 0 means disabled.
- st,stm32mp1-booster
st,syscfg:
- allOf:
- - $ref: "/schemas/types.yaml#/definitions/phandle-array"
+ $ref: "/schemas/types.yaml#/definitions/phandle-array"
description: phandle to system configuration controller.
vdda-supply:
"^(reg11|reg18|usb33)$":
type: object
- allOf:
- - $ref: "regulator.yaml#"
+ $ref: "regulator.yaml#"
required:
- compatible
maxItems: 1
st,syscfg-holdboot:
- allOf:
- - $ref: "/schemas/types.yaml#/definitions/phandle-array"
description: remote processor reset hold boot
- Phandle of syscon block.
- The offset of the hold boot setting register.
- The field mask of the hold boot.
+ $ref: "/schemas/types.yaml#/definitions/phandle-array"
maxItems: 1
st,syscfg-tz:
- allOf:
- - $ref: "/schemas/types.yaml#/definitions/phandle-array"
description:
Reference to the system configuration which holds the RCC trust zone mode
- Phandle of syscon block.
- The offset of the RCC trust zone mode register.
- The field mask of the RCC trust zone mode.
+ $ref: "/schemas/types.yaml#/definitions/phandle-array"
maxItems: 1
interrupts:
(see ../reserved-memory/reserved-memory.txt)
st,syscfg-pdds:
- allOf:
- - $ref: "/schemas/types.yaml#/definitions/phandle-array"
+ $ref: "/schemas/types.yaml#/definitions/phandle-array"
description: |
Reference to the system configuration which holds the remote
1st cell: phandle to syscon block
intel,global-reset:
description: Global reset register offset and bit offset.
- allOf:
- - $ref: /schemas/types.yaml#/definitions/uint32-array
+ $ref: /schemas/types.yaml#/definitions/uint32-array
items:
- description: Register offset
- description: Register bit offset
and identifies the type of the hart.
mmu-type:
- allOf:
- - $ref: "/schemas/types.yaml#/definitions/string"
- - enum:
- - riscv,sv32
- - riscv,sv39
- - riscv,sv48
description:
Identifies the MMU address translation mode used on this
hart. These values originate from the RISC-V Privileged
Specification document, available from
https://riscv.org/specifications/
+ $ref: "/schemas/types.yaml#/definitions/string"
+ enum:
+ - riscv,sv32
+ - riscv,sv39
+ - riscv,sv48
riscv,isa:
- allOf:
- - $ref: "/schemas/types.yaml#/definitions/string"
- - enum:
- - rv64imac
- - rv64imafdc
description:
Identifies the specific RISC-V instruction set architecture
supported by the hart. These are documented in the RISC-V
While the isa strings in ISA specification are case
insensitive, letters in the riscv,isa string must be all
lowercase to simplify parsing.
+ $ref: "/schemas/types.yaml#/definitions/string"
+ enum:
+ - rv64imac
+ - rv64imafdc
# RISC-V requires 'timebase-frequency' in /cpus, so disallow it here
timebase-frequency: false
maxItems: 1
st,syscfg:
- allOf:
- - $ref: "/schemas/types.yaml#/definitions/phandle-array"
- - items:
- minItems: 3
- maxItems: 3
+ $ref: "/schemas/types.yaml#/definitions/phandle-array"
+ items:
+ minItems: 3
+ maxItems: 3
description: |
Phandle/offset/mask triplet. The phandle to pwrcfg used to
access control register at offset, and change the dbp (Disable Backup
description:
Rate at which poll occurs when auto-poll is set.
default 100ms.
- allOf:
- - $ref: /schemas/types.yaml#/definitions/uint32
- - default: 100
+ $ref: /schemas/types.yaml#/definitions/uint32
+ default: 100
poll-timeout-ms:
description:
Poll timeout when auto-poll is set, default
3000ms.
- allOf:
- - $ref: /schemas/types.yaml#/definitions/uint32
- - default: 3000
+ $ref: /schemas/types.yaml#/definitions/uint32
+ default: 3000
required:
- compatible
properties:
rs485-rts-delay:
description: prop-encoded-array <a b>
- allOf:
- - $ref: /schemas/types.yaml#/definitions/uint32-array
- - items:
- items:
- - description:
- Delay between rts signal and beginning of data sent in milliseconds.
- It corresponds to the delay before sending data.
- default: 0
- maximum: 1000
- - description:
- Delay between end of data sent and rts signal in milliseconds.
- It corresponds to the delay after sending data and actual release of the line.
- default: 0
- maximum: 1000
+ $ref: /schemas/types.yaml#/definitions/uint32-array
+ items:
+ items:
+ - description: Delay between rts signal and beginning of data sent in
+ milliseconds. It corresponds to the delay before sending data.
+ default: 0
+ maximum: 1000
+ - description: Delay between end of data sent and rts signal in milliseconds.
+ It corresponds to the delay after sending data and actual release
+ of the line.
+ default: 0
+ maximum: 1000
rs485-rts-active-low:
description: drive RTS low when sending (default is high).
samsung,uart-fifosize:
description: The fifo size supported by the UART channel.
- allOf:
- - $ref: /schemas/types.yaml#/definitions/uint32
- - enum: [16, 64, 256]
+ $ref: /schemas/types.yaml#/definitions/uint32
+ enum: [16, 64, 256]
required:
- compatible
adi,decimation-ratio:
description: |
This property set's the decimation ratio of PDM to PCM audio data.
- allOf:
- - $ref: /schemas/types.yaml#/definitions/uint32
- - enum: [64, 32, 16]
- default: 64
+ $ref: /schemas/types.yaml#/definitions/uint32
+ enum: [64, 32, 16]
+ default: 64
adi,pdm-clk-map:
description: |
The ADAU7118 has two PDM clocks for the four Inputs. Each input must be
assigned to one of these two clocks. This property set's the mapping
between the clocks and the inputs.
- allOf:
- - $ref: /schemas/types.yaml#/definitions/uint32-array
- - minItems: 4
- maxItems: 4
- items:
- maximum: 1
- default: [0, 0, 1, 1]
+ $ref: /schemas/types.yaml#/definitions/uint32-array
+ minItems: 4
+ maxItems: 4
+ items:
+ maximum: 1
+ default: [0, 0, 1, 1]
required:
- "#sound-dai-cells"
A list of the connections between audio components. Each entry
is a pair of strings, the first being the connection's sink, the
second being the connection's source.
- allOf:
- - $ref: /schemas/types.yaml#definitions/non-unique-string-array
- - minItems: 2
- maxItems: 18
- items:
- enum:
- # Audio Pins on the SoC
- - HP
- - HPCOM
- - LINEIN
- - LINEOUT
- - MIC1
- - MIC2
- - MIC3
-
- # Microphone Biases from the SoC
- - HBIAS
- - MBIAS
-
- # Board Connectors
- - Headphone
- - Headset Mic
- - Line In
- - Line Out
- - Mic
- - Speaker
+ $ref: /schemas/types.yaml#definitions/non-unique-string-array
+ minItems: 2
+ maxItems: 18
+ items:
+ enum:
+ # Audio Pins on the SoC
+ - HP
+ - HPCOM
+ - LINEIN
+ - LINEOUT
+ - MIC1
+ - MIC2
+ - MIC3
+
+ # Microphone Biases from the SoC
+ - HBIAS
+ - MBIAS
+
+ # Board Connectors
+ - Headphone
+ - Headset Mic
+ - Line In
+ - Line Out
+ - Mic
+ - Speaker
allwinner,codec-analog-controls:
$ref: /schemas/types.yaml#/definitions/phandle
gpio@42:
type: object
- allOf:
- - $ref: ../gpio/qcom,wcd934x-gpio.yaml#
+ $ref: ../gpio/qcom,wcd934x-gpio.yaml#
patternProperties:
"^.*@[0-9a-f]+$":
- const: rx
rockchip,capture-channels:
- allOf:
- - $ref: /schemas/types.yaml#/definitions/uint32
+ $ref: /schemas/types.yaml#/definitions/uint32
default: 2
description:
Max capture channels, if not set, 2 channels default.
rockchip,playback-channels:
- allOf:
- - $ref: /schemas/types.yaml#/definitions/uint32
+ $ref: /schemas/types.yaml#/definitions/uint32
default: 8
description:
Max playback channels, if not set, 8 channels default.
0 - Mic bias is set to VREF
1 - Mic bias is set to VREF × 1.096
6 - Mic bias is set to AVDD
- allOf:
- - $ref: /schemas/types.yaml#/definitions/uint32
- - enum: [0, 1, 6]
+ $ref: /schemas/types.yaml#/definitions/uint32
+ enum: [0, 1, 6]
ti,vref-source:
description: |
0 - Set VREF to 2.75V
1 - Set VREF to 2.5V
2 - Set VREF to 1.375V
- allOf:
- - $ref: /schemas/types.yaml#/definitions/uint32
- - enum: [0, 1, 2]
+ $ref: /schemas/types.yaml#/definitions/uint32
+ enum: [0, 1, 2]
required:
- compatible
renesas,dtdl:
description: delay sync signal (setup) in transmit mode.
- allOf:
- - $ref: /schemas/types.yaml#/definitions/uint32
- - enum:
- - 0 # no bit delay
- - 50 # 0.5-clock-cycle delay
- - 100 # 1-clock-cycle delay
- - 150 # 1.5-clock-cycle delay
- - 200 # 2-clock-cycle delay
+ $ref: /schemas/types.yaml#/definitions/uint32
+ enum:
+ - 0 # no bit delay
+ - 50 # 0.5-clock-cycle delay
+ - 100 # 1-clock-cycle delay
+ - 150 # 1.5-clock-cycle delay
+ - 200 # 2-clock-cycle delay
renesas,syncdl:
description: delay sync signal (hold) in transmit mode
- allOf:
- - $ref: /schemas/types.yaml#/definitions/uint32
- - enum:
- - 0 # no bit delay
- - 50 # 0.5-clock-cycle delay
- - 100 # 1-clock-cycle delay
- - 150 # 1.5-clock-cycle delay
- - 200 # 2-clock-cycle delay
- - 300 # 3-clock-cycle delay
+ $ref: /schemas/types.yaml#/definitions/uint32
+ enum:
+ - 0 # no bit delay
+ - 50 # 0.5-clock-cycle delay
+ - 100 # 1-clock-cycle delay
+ - 150 # 1.5-clock-cycle delay
+ - 200 # 2-clock-cycle delay
+ - 300 # 3-clock-cycle delay
renesas,tx-fifo-size:
# deprecated for soctype-specific bindings
description: |
Override the default TX fifo size. Unit is words. Ignored if 0.
- allOf:
- - $ref: /schemas/types.yaml#/definitions/uint32
- - maxItems: 1
+ $ref: /schemas/types.yaml#/definitions/uint32
+ maxItems: 1
default: 64
renesas,rx-fifo-size:
# deprecated for soctype-specific bindings
description: |
Override the default RX fifo size. Unit is words. Ignored if 0.
- allOf:
- - $ref: /schemas/types.yaml#/definitions/uint32
- - maxItems: 1
+ $ref: /schemas/types.yaml#/definitions/uint32
+ maxItems: 1
default: 64
required:
Maximum SPI clocking speed of the device in Hz.
spi-rx-bus-width:
- allOf:
- - $ref: /schemas/types.yaml#/definitions/uint32
- - enum: [ 1, 2, 4, 8 ]
- - default: 1
description:
Bus width to the SPI bus used for read transfers.
+ $ref: /schemas/types.yaml#/definitions/uint32
+ enum: [1, 2, 4, 8]
+ default: 1
spi-rx-delay-us:
description:
Delay, in microseconds, after a read transfer.
spi-tx-bus-width:
- allOf:
- - $ref: /schemas/types.yaml#/definitions/uint32
- - enum: [ 1, 2, 4, 8 ]
- - default: 1
description:
Bus width to the SPI bus used for write transfers.
+ $ref: /schemas/types.yaml#/definitions/uint32
+ enum: [1, 2, 4, 8]
+ default: 1
spi-tx-delay-us:
description:
properties:
pl022,interface:
description: SPI interface type
- allOf:
- - $ref: "/schemas/types.yaml#/definitions/uint32"
- - enum:
- - 0 # SPI
- - 1 # Texas Instruments Synchronous Serial Frame Format
- - 2 # Microwire (Half Duplex)
+ $ref: "/schemas/types.yaml#/definitions/uint32"
+ enum:
+ - 0 # SPI
+ - 1 # Texas Instruments Synchronous Serial Frame Format
+ - 2 # Microwire (Half Duplex)
pl022,com-mode:
description: Specifies the transfer mode
- allOf:
- - $ref: "/schemas/types.yaml#/definitions/uint32"
- - enum:
- - 0 # interrupt mode
- - 1 # polling mode
- - 2 # DMA mode
- default: 1
+ $ref: "/schemas/types.yaml#/definitions/uint32"
+ enum:
+ - 0 # interrupt mode
+ - 1 # polling mode
+ - 2 # DMA mode
+ default: 1
pl022,rx-level-trig:
description: Rx FIFO watermark level
- allOf:
- - $ref: "/schemas/types.yaml#/definitions/uint32"
- - minimum: 0
- maximum: 4
+ $ref: "/schemas/types.yaml#/definitions/uint32"
+ minimum: 0
+ maximum: 4
pl022,tx-level-trig:
description: Tx FIFO watermark level
- allOf:
- - $ref: "/schemas/types.yaml#/definitions/uint32"
- - minimum: 0
- maximum: 4
+ $ref: "/schemas/types.yaml#/definitions/uint32"
+ minimum: 0
+ maximum: 4
pl022,ctrl-len:
description: Microwire interface - Control length
- allOf:
- - $ref: "/schemas/types.yaml#/definitions/uint32"
- - minimum: 0x03
- maximum: 0x1f
+ $ref: "/schemas/types.yaml#/definitions/uint32"
+ minimum: 0x03
+ maximum: 0x1f
pl022,wait-state:
description: Microwire interface - Wait state
- allOf:
- - $ref: "/schemas/types.yaml#/definitions/uint32"
- - enum: [ 0, 1 ]
+ $ref: "/schemas/types.yaml#/definitions/uint32"
+ enum: [0, 1]
pl022,duplex:
description: Microwire interface - Full/Half duplex
- allOf:
- - $ref: "/schemas/types.yaml#/definitions/uint32"
- - enum: [ 0, 1 ]
+ $ref: "/schemas/types.yaml#/definitions/uint32"
+ enum: [0, 1]
required:
- compatible
sifive,fifo-depth:
description:
Depth of hardware queues; defaults to 8
- allOf:
- - $ref: "/schemas/types.yaml#/definitions/uint32"
- - enum: [ 8 ]
- - default: 8
+ $ref: "/schemas/types.yaml#/definitions/uint32"
+ enum: [8]
+ default: 8
sifive,max-bits-per-word:
description:
Maximum bits per word; defaults to 8
- allOf:
- - $ref: "/schemas/types.yaml#/definitions/uint32"
- - enum: [ 0, 1, 2, 3, 4, 5, 6, 7, 8 ]
- - default: 8
+ $ref: "/schemas/types.yaml#/definitions/uint32"
+ enum: [0, 1, 2, 3, 4, 5, 6, 7, 8]
+ default: 8
required:
- compatible
- const: calib_sel
"#qcom,sensors":
- allOf:
- - $ref: /schemas/types.yaml#/definitions/uint32
- - minimum: 1
- - maximum: 16
description:
Number of sensors enabled on this platform
+ $ref: /schemas/types.yaml#/definitions/uint32
+ minimum: 1
+ maximum: 16
"#thermal-sensor-cells":
const: 1
description: A timer node has up to 8 frame sub-nodes, each with the following properties.
properties:
frame-number:
- allOf:
- - $ref: "/schemas/types.yaml#/definitions/uint32"
- - minimum: 0
- maximum: 7
+ $ref: "/schemas/types.yaml#/definitions/uint32"
+ minimum: 0
+ maximum: 7
interrupts:
minItems: 1
ingenic,pwm-channels-mask:
description: Bitmask of TCU channels reserved for PWM use.
- allOf:
- - $ref: /schemas/types.yaml#/definitions/uint32
- - minimum: 0x00
- - maximum: 0xff
- - default: 0xfc
+ $ref: /schemas/types.yaml#/definitions/uint32
+ minimum: 0x00
+ maximum: 0xff
+ default: 0xfc
patternProperties:
"^watchdog@[a-f0-9]+$":
type: object
- allOf: [ $ref: ../watchdog/watchdog.yaml# ]
+ $ref: ../watchdog/watchdog.yaml#
properties:
compatible:
oneOf:
"^pwm@[a-f0-9]+$":
type: object
- allOf: [ $ref: ../pwm/pwm.yaml# ]
+ $ref: ../pwm/pwm.yaml#
properties:
compatible:
oneOf:
aspeed,vhub-downstream-ports:
description: Number of downstream ports supported by the Virtual Hub
- allOf:
- - $ref: /schemas/types.yaml#/definitions/uint32
- - default: 5
- minimum: 1
- maximum: 7
+ $ref: /schemas/types.yaml#/definitions/uint32
+ default: 5
+ minimum: 1
+ maximum: 7
aspeed,vhub-generic-endpoints:
description: Number of generic endpoints supported by the Virtual Hub
- allOf:
- - $ref: /schemas/types.yaml#/definitions/uint32
- - default: 15
- minimum: 1
- maximum: 21
+ $ref: /schemas/types.yaml#/definitions/uint32
+ default: 15
+ minimum: 1
+ maximum: 21
required:
- compatible
projects / linux.git / commitdiff