- const: xlnx,zynqmp-zcu111
- const: xlnx,zynqmp
+ - description: Xilinx Kria SOMs
+ items:
+ - const: xlnx,zynqmp-sm-k26-rev1
+ - const: xlnx,zynqmp-sm-k26-revB
+ - const: xlnx,zynqmp-sm-k26-revA
+ - const: xlnx,zynqmp-sm-k26
+ - const: xlnx,zynqmp
+
+ - description: Xilinx Kria SOMs (starter)
+ items:
+ - const: xlnx,zynqmp-smk-k26-rev1
+ - const: xlnx,zynqmp-smk-k26-revB
+ - const: xlnx,zynqmp-smk-k26-revA
+ - const: xlnx,zynqmp-smk-k26
+ - const: xlnx,zynqmp
+
additionalProperties: true
...
dtb-$(CONFIG_ARCH_ZYNQMP) += zynqmp-zcu104-revC.dtb
dtb-$(CONFIG_ARCH_ZYNQMP) += zynqmp-zcu106-revA.dtb
dtb-$(CONFIG_ARCH_ZYNQMP) += zynqmp-zcu111-revA.dtb
+
+dtb-$(CONFIG_ARCH_ZYNQMP) += zynqmp-sm-k26-revA.dtb
+dtb-$(CONFIG_ARCH_ZYNQMP) += zynqmp-smk-k26-revA.dtb
+
+sm-k26-revA-sck-kv-g-revA-dtbs := zynqmp-sm-k26-revA.dtb zynqmp-sck-kv-g-revA.dtbo
+sm-k26-revA-sck-kv-g-revB-dtbs := zynqmp-sm-k26-revA.dtb zynqmp-sck-kv-g-revB.dtbo
+smk-k26-revA-sm-k26-revA-sck-kv-g-revA-dtbs := zynqmp-smk-k26-revA.dtb zynqmp-sck-kv-g-revA.dtbo
+smk-k26-revA-sm-k26-revA-sck-kv-g-revB-dtbs := zynqmp-smk-k26-revA.dtb zynqmp-sck-kv-g-revB.dtbo
+
+dtb-$(CONFIG_ARCH_ZYNQMP) += sm-k26-revA-sck-kv-g-revA.dtb
+dtb-$(CONFIG_ARCH_ZYNQMP) += sm-k26-revA-sck-kv-g-revB.dtb
+dtb-$(CONFIG_ARCH_ZYNQMP) += smk-k26-revA-sm-k26-revA-sck-kv-g-revA.dtb
+dtb-$(CONFIG_ARCH_ZYNQMP) += smk-k26-revA-sm-k26-revA-sck-kv-g-revB.dtb
--- /dev/null
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * dts file for KV260 revA Carrier Card
+ *
+ * (C) Copyright 2020 - 2021, Xilinx, Inc.
+ *
+ * SD level shifter:
+ * "A" – A01 board un-modified (NXP)
+ * "Y" – A01 board modified with legacy interposer (Nexperia)
+ * "Z" – A01 board modified with Diode interposer
+ *
+ * Michal Simek <michal.simek@xilinx.com>
+ */
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/net/ti-dp83867.h>
+#include <dt-bindings/phy/phy.h>
+#include <dt-bindings/pinctrl/pinctrl-zynqmp.h>
+
+/dts-v1/;
+/plugin/;
+
+&i2c1 { /* I2C_SCK C23/C24 - MIO from SOM */
+ #address-cells = <1>;
+ #size-cells = <0>;
+ pinctrl-names = "default", "gpio";
+ pinctrl-0 = <&pinctrl_i2c1_default>;
+ pinctrl-1 = <&pinctrl_i2c1_gpio>;
+ scl-gpios = <&gpio 24 GPIO_ACTIVE_HIGH>;
+ sda-gpios = <&gpio 25 GPIO_ACTIVE_HIGH>;
+
+ /* u14 - 0x40 - ina260 */
+ /* u27 - 0xe0 - STDP4320 DP/HDMI splitter */
+};
+
+&amba {
+ si5332_0: si5332_0 { /* u17 */
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <125000000>;
+ };
+
+ si5332_1: si5332_1 { /* u17 */
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <25000000>;
+ };
+
+ si5332_2: si5332_2 { /* u17 */
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <48000000>;
+ };
+
+ si5332_3: si5332_3 { /* u17 */
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <24000000>;
+ };
+
+ si5332_4: si5332_4 { /* u17 */
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <26000000>;
+ };
+
+ si5332_5: si5332_5 { /* u17 */
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <27000000>;
+ };
+};
+
+/* DP/USB 3.0 and SATA */
+&psgtr {
+ status = "okay";
+ /* pcie, usb3, sata */
+ clocks = <&si5332_5>, <&si5332_4>, <&si5332_0>;
+ clock-names = "ref0", "ref1", "ref2";
+};
+
+&sata {
+ status = "okay";
+ /* SATA OOB timing settings */
+ ceva,p0-cominit-params = /bits/ 8 <0x18 0x40 0x18 0x28>;
+ ceva,p0-comwake-params = /bits/ 8 <0x06 0x14 0x08 0x0E>;
+ ceva,p0-burst-params = /bits/ 8 <0x13 0x08 0x4A 0x06>;
+ ceva,p0-retry-params = /bits/ 16 <0x96A4 0x3FFC>;
+ ceva,p1-cominit-params = /bits/ 8 <0x18 0x40 0x18 0x28>;
+ ceva,p1-comwake-params = /bits/ 8 <0x06 0x14 0x08 0x0E>;
+ ceva,p1-burst-params = /bits/ 8 <0x13 0x08 0x4A 0x06>;
+ ceva,p1-retry-params = /bits/ 16 <0x96A4 0x3FFC>;
+ phy-names = "sata-phy";
+ phys = <&psgtr 3 PHY_TYPE_SATA 1 2>;
+};
+
+&zynqmp_dpsub {
+ status = "disabled";
+ phy-names = "dp-phy0", "dp-phy1";
+ phys = <&psgtr 1 PHY_TYPE_DP 0 0>, <&psgtr 0 PHY_TYPE_DP 1 0>;
+};
+
+&zynqmp_dpdma {
+ status = "okay";
+};
+
+&usb0 {
+ status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usb0_default>;
+ phy-names = "usb3-phy";
+ phys = <&psgtr 2 PHY_TYPE_USB3 0 1>;
+ /* missing usb5744 - u43 */
+};
+
+&dwc3_0 {
+ status = "okay";
+ dr_mode = "host";
+ snps,usb3_lpm_capable;
+ maximum-speed = "super-speed";
+};
+
+&sdhci1 { /* on CC with tuned parameters */
+ status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_sdhci1_default>;
+ /*
+ * SD 3.0 requires level shifter and this property
+ * should be removed if the board has level shifter and
+ * need to work in UHS mode
+ */
+ no-1-8-v;
+ disable-wp;
+ xlnx,mio-bank = <1>;
+};
+
+&gem3 { /* required by spec */
+ status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_gem3_default>;
+ phy-handle = <&phy0>;
+ phy-mode = "rgmii-id";
+
+ mdio: mdio {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reset-gpios = <&gpio 38 GPIO_ACTIVE_LOW>;
+ reset-delay-us = <2>;
+
+ phy0: ethernet-phy@1 {
+ #phy-cells = <1>;
+ reg = <1>;
+ ti,rx-internal-delay = <DP83867_RGMIIDCTL_2_25_NS>;
+ ti,tx-internal-delay = <DP83867_RGMIIDCTL_2_75_NS>;
+ ti,fifo-depth = <DP83867_PHYCR_FIFO_DEPTH_4_B_NIB>;
+ ti,dp83867-rxctrl-strap-quirk;
+ };
+ };
+};
+
+&pinctrl0 { /* required by spec */
+ status = "okay";
+
+ pinctrl_uart1_default: uart1-default {
+ conf {
+ groups = "uart1_9_grp";
+ slew-rate = <SLEW_RATE_SLOW>;
+ power-source = <IO_STANDARD_LVCMOS18>;
+ drive-strength = <12>;
+ };
+
+ conf-rx {
+ pins = "MIO37";
+ bias-high-impedance;
+ };
+
+ conf-tx {
+ pins = "MIO36";
+ bias-disable;
+ };
+
+ mux {
+ groups = "uart1_9_grp";
+ function = "uart1";
+ };
+ };
+
+ pinctrl_i2c1_default: i2c1-default {
+ conf {
+ groups = "i2c1_6_grp";
+ bias-pull-up;
+ slew-rate = <SLEW_RATE_SLOW>;
+ power-source = <IO_STANDARD_LVCMOS18>;
+ };
+
+ mux {
+ groups = "i2c1_6_grp";
+ function = "i2c1";
+ };
+ };
+
+ pinctrl_i2c1_gpio: i2c1-gpio {
+ conf {
+ groups = "gpio0_24_grp", "gpio0_25_grp";
+ slew-rate = <SLEW_RATE_SLOW>;
+ power-source = <IO_STANDARD_LVCMOS18>;
+ };
+
+ mux {
+ groups = "gpio0_24_grp", "gpio0_25_grp";
+ function = "gpio0";
+ };
+ };
+
+ pinctrl_gem3_default: gem3-default {
+ conf {
+ groups = "ethernet3_0_grp";
+ slew-rate = <SLEW_RATE_SLOW>;
+ power-source = <IO_STANDARD_LVCMOS18>;
+ };
+
+ conf-rx {
+ pins = "MIO70", "MIO72", "MIO74";
+ bias-high-impedance;
+ low-power-disable;
+ };
+
+ conf-bootstrap {
+ pins = "MIO71", "MIO73", "MIO75";
+ bias-disable;
+ low-power-disable;
+ };
+
+ conf-tx {
+ pins = "MIO64", "MIO65", "MIO66",
+ "MIO67", "MIO68", "MIO69";
+ bias-disable;
+ low-power-enable;
+ };
+
+ conf-mdio {
+ groups = "mdio3_0_grp";
+ slew-rate = <SLEW_RATE_SLOW>;
+ power-source = <IO_STANDARD_LVCMOS18>;
+ bias-disable;
+ };
+
+ mux-mdio {
+ function = "mdio3";
+ groups = "mdio3_0_grp";
+ };
+
+ mux {
+ function = "ethernet3";
+ groups = "ethernet3_0_grp";
+ };
+ };
+
+ pinctrl_usb0_default: usb0-default {
+ conf {
+ groups = "usb0_0_grp";
+ slew-rate = <SLEW_RATE_SLOW>;
+ power-source = <IO_STANDARD_LVCMOS18>;
+ };
+
+ conf-rx {
+ pins = "MIO52", "MIO53", "MIO55";
+ bias-high-impedance;
+ };
+
+ conf-tx {
+ pins = "MIO54", "MIO56", "MIO57", "MIO58", "MIO59",
+ "MIO60", "MIO61", "MIO62", "MIO63";
+ bias-disable;
+ };
+
+ mux {
+ groups = "usb0_0_grp";
+ function = "usb0";
+ };
+ };
+
+ pinctrl_sdhci1_default: sdhci1-default {
+ conf {
+ groups = "sdio1_0_grp";
+ slew-rate = <SLEW_RATE_SLOW>;
+ power-source = <IO_STANDARD_LVCMOS18>;
+ bias-disable;
+ };
+
+ conf-cd {
+ groups = "sdio1_cd_0_grp";
+ bias-high-impedance;
+ bias-pull-up;
+ slew-rate = <SLEW_RATE_SLOW>;
+ power-source = <IO_STANDARD_LVCMOS18>;
+ };
+
+ mux-cd {
+ groups = "sdio1_cd_0_grp";
+ function = "sdio1_cd";
+ };
+
+ mux {
+ groups = "sdio1_0_grp";
+ function = "sdio1";
+ };
+ };
+};
+
+&uart1 {
+ status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart1_default>;
+};
--- /dev/null
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * dts file for KV260 revA Carrier Card
+ *
+ * (C) Copyright 2020 - 2021, Xilinx, Inc.
+ *
+ * Michal Simek <michal.simek@xilinx.com>
+ */
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/net/ti-dp83867.h>
+#include <dt-bindings/phy/phy.h>
+#include <dt-bindings/pinctrl/pinctrl-zynqmp.h>
+
+/dts-v1/;
+/plugin/;
+
+&i2c1 { /* I2C_SCK C23/C24 - MIO from SOM */
+ #address-cells = <1>;
+ #size-cells = <0>;
+ pinctrl-names = "default", "gpio";
+ pinctrl-0 = <&pinctrl_i2c1_default>;
+ pinctrl-1 = <&pinctrl_i2c1_gpio>;
+ scl-gpios = <&gpio 24 GPIO_ACTIVE_HIGH>;
+ sda-gpios = <&gpio 25 GPIO_ACTIVE_HIGH>;
+
+ /* u14 - 0x40 - ina260 */
+ /* u43 - 0x2d - usb5744 */
+ /* u27 - 0xe0 - STDP4320 DP/HDMI splitter */
+};
+
+&amba {
+ si5332_0: si5332_0 { /* u17 */
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <125000000>;
+ };
+
+ si5332_1: si5332_1 { /* u17 */
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <25000000>;
+ };
+
+ si5332_2: si5332_2 { /* u17 */
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <48000000>;
+ };
+
+ si5332_3: si5332_3 { /* u17 */
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <24000000>;
+ };
+
+ si5332_4: si5332_4 { /* u17 */
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <26000000>;
+ };
+
+ si5332_5: si5332_5 { /* u17 */
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <27000000>;
+ };
+};
+
+/* DP/USB 3.0 */
+&psgtr {
+ status = "okay";
+ /* pcie, usb3, sata */
+ clocks = <&si5332_5>, <&si5332_4>, <&si5332_0>;
+ clock-names = "ref0", "ref1", "ref2";
+};
+
+&zynqmp_dpsub {
+ status = "disabled";
+ phy-names = "dp-phy0", "dp-phy1";
+ phys = <&psgtr 1 PHY_TYPE_DP 0 0>, <&psgtr 0 PHY_TYPE_DP 1 0>;
+};
+
+&zynqmp_dpdma {
+ status = "okay";
+};
+
+&usb0 {
+ status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usb0_default>;
+ phy-names = "usb3-phy";
+ phys = <&psgtr 2 PHY_TYPE_USB3 0 1>;
+};
+
+&dwc3_0 {
+ status = "okay";
+ dr_mode = "host";
+ snps,usb3_lpm_capable;
+ maximum-speed = "super-speed";
+};
+
+&sdhci1 { /* on CC with tuned parameters */
+ status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_sdhci1_default>;
+ /*
+ * SD 3.0 requires level shifter and this property
+ * should be removed if the board has level shifter and
+ * need to work in UHS mode
+ */
+ no-1-8-v;
+ disable-wp;
+ xlnx,mio-bank = <1>;
+ clk-phase-sd-hs = <126>, <60>;
+ clk-phase-uhs-sdr25 = <120>, <60>;
+ clk-phase-uhs-ddr50 = <126>, <48>;
+};
+
+&gem3 { /* required by spec */
+ status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_gem3_default>;
+ phy-handle = <&phy0>;
+ phy-mode = "rgmii-id";
+
+ mdio: mdio {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reset-gpios = <&gpio 38 GPIO_ACTIVE_LOW>;
+ reset-delay-us = <2>;
+
+ phy0: ethernet-phy@1 {
+ #phy-cells = <1>;
+ reg = <1>;
+ ti,rx-internal-delay = <DP83867_RGMIIDCTL_2_25_NS>;
+ ti,tx-internal-delay = <DP83867_RGMIIDCTL_2_75_NS>;
+ ti,fifo-depth = <DP83867_PHYCR_FIFO_DEPTH_4_B_NIB>;
+ ti,dp83867-rxctrl-strap-quirk;
+ };
+ };
+};
+
+&pinctrl0 { /* required by spec */
+ status = "okay";
+
+ pinctrl_uart1_default: uart1-default {
+ conf {
+ groups = "uart1_9_grp";
+ slew-rate = <SLEW_RATE_SLOW>;
+ power-source = <IO_STANDARD_LVCMOS18>;
+ drive-strength = <12>;
+ };
+
+ conf-rx {
+ pins = "MIO37";
+ bias-high-impedance;
+ };
+
+ conf-tx {
+ pins = "MIO36";
+ bias-disable;
+ };
+
+ mux {
+ groups = "uart1_9_grp";
+ function = "uart1";
+ };
+ };
+
+ pinctrl_i2c1_default: i2c1-default {
+ conf {
+ groups = "i2c1_6_grp";
+ bias-pull-up;
+ slew-rate = <SLEW_RATE_SLOW>;
+ power-source = <IO_STANDARD_LVCMOS18>;
+ };
+
+ mux {
+ groups = "i2c1_6_grp";
+ function = "i2c1";
+ };
+ };
+
+ pinctrl_i2c1_gpio: i2c1-gpio {
+ conf {
+ groups = "gpio0_24_grp", "gpio0_25_grp";
+ slew-rate = <SLEW_RATE_SLOW>;
+ power-source = <IO_STANDARD_LVCMOS18>;
+ };
+
+ mux {
+ groups = "gpio0_24_grp", "gpio0_25_grp";
+ function = "gpio0";
+ };
+ };
+
+ pinctrl_gem3_default: gem3-default {
+ conf {
+ groups = "ethernet3_0_grp";
+ slew-rate = <SLEW_RATE_SLOW>;
+ power-source = <IO_STANDARD_LVCMOS18>;
+ };
+
+ conf-rx {
+ pins = "MIO70", "MIO72", "MIO74";
+ bias-high-impedance;
+ low-power-disable;
+ };
+
+ conf-bootstrap {
+ pins = "MIO71", "MIO73", "MIO75";
+ bias-disable;
+ low-power-disable;
+ };
+
+ conf-tx {
+ pins = "MIO64", "MIO65", "MIO66",
+ "MIO67", "MIO68", "MIO69";
+ bias-disable;
+ low-power-enable;
+ };
+
+ conf-mdio {
+ groups = "mdio3_0_grp";
+ slew-rate = <SLEW_RATE_SLOW>;
+ power-source = <IO_STANDARD_LVCMOS18>;
+ bias-disable;
+ };
+
+ mux-mdio {
+ function = "mdio3";
+ groups = "mdio3_0_grp";
+ };
+
+ mux {
+ function = "ethernet3";
+ groups = "ethernet3_0_grp";
+ };
+ };
+
+ pinctrl_usb0_default: usb0-default {
+ conf {
+ groups = "usb0_0_grp";
+ slew-rate = <SLEW_RATE_SLOW>;
+ power-source = <IO_STANDARD_LVCMOS18>;
+ };
+
+ conf-rx {
+ pins = "MIO52", "MIO53", "MIO55";
+ bias-high-impedance;
+ };
+
+ conf-tx {
+ pins = "MIO54", "MIO56", "MIO57", "MIO58", "MIO59",
+ "MIO60", "MIO61", "MIO62", "MIO63";
+ bias-disable;
+ };
+
+ mux {
+ groups = "usb0_0_grp";
+ function = "usb0";
+ };
+ };
+
+ pinctrl_sdhci1_default: sdhci1-default {
+ conf {
+ groups = "sdio1_0_grp";
+ slew-rate = <SLEW_RATE_SLOW>;
+ power-source = <IO_STANDARD_LVCMOS18>;
+ bias-disable;
+ };
+
+ conf-cd {
+ groups = "sdio1_cd_0_grp";
+ bias-high-impedance;
+ bias-pull-up;
+ slew-rate = <SLEW_RATE_SLOW>;
+ power-source = <IO_STANDARD_LVCMOS18>;
+ };
+
+ mux-cd {
+ groups = "sdio1_cd_0_grp";
+ function = "sdio1_cd";
+ };
+
+ mux {
+ groups = "sdio1_0_grp";
+ function = "sdio1";
+ };
+ };
+};
+
+&uart1 {
+ status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart1_default>;
+};
--- /dev/null
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * dts file for Xilinx ZynqMP SM-K26 rev1/B/A
+ *
+ * (C) Copyright 2020 - 2021, Xilinx, Inc.
+ *
+ * Michal Simek <michal.simek@xilinx.com>
+ */
+
+/dts-v1/;
+
+#include "zynqmp.dtsi"
+#include "zynqmp-clk-ccf.dtsi"
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/phy/phy.h>
+
+/ {
+ model = "ZynqMP SM-K26 Rev1/B/A";
+ compatible = "xlnx,zynqmp-sm-k26-rev1", "xlnx,zynqmp-sm-k26-revB",
+ "xlnx,zynqmp-sm-k26-revA", "xlnx,zynqmp-sm-k26",
+ "xlnx,zynqmp";
+
+ aliases {
+ i2c0 = &i2c0;
+ i2c1 = &i2c1;
+ mmc0 = &sdhci0;
+ mmc1 = &sdhci1;
+ nvmem0 = &eeprom;
+ nvmem1 = &eeprom_cc;
+ rtc0 = &rtc;
+ serial0 = &uart0;
+ serial1 = &uart1;
+ serial2 = &dcc;
+ spi0 = &qspi;
+ spi1 = &spi0;
+ spi2 = &spi1;
+ usb0 = &usb0;
+ usb1 = &usb1;
+ };
+
+ chosen {
+ bootargs = "earlycon";
+ stdout-path = "serial1:115200n8";
+ };
+
+ memory@0 {
+ device_type = "memory"; /* 4GB */
+ reg = <0x0 0x0 0x0 0x80000000>, <0x8 0x00000000 0x0 0x80000000>;
+ };
+
+ gpio-keys {
+ compatible = "gpio-keys";
+ autorepeat;
+ fwuen {
+ label = "fwuen";
+ gpios = <&gpio 12 GPIO_ACTIVE_LOW>;
+ };
+ };
+
+ leds {
+ compatible = "gpio-leds";
+ ds35-led {
+ label = "heartbeat";
+ gpios = <&gpio 7 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "heartbeat";
+ };
+
+ ds36-led {
+ label = "vbus_det";
+ gpios = <&gpio 8 GPIO_ACTIVE_HIGH>;
+ default-state = "on";
+ };
+ };
+};
+
+&uart1 { /* MIO36/MIO37 */
+ status = "okay";
+};
+
+&qspi { /* MIO 0-5 - U143 */
+ status = "okay";
+ flash@0 { /* MT25QU512A */
+ compatible = "mt25qu512a", "jedec,spi-nor"; /* 64MB */
+ #address-cells = <1>;
+ #size-cells = <1>;
+ reg = <0>;
+ spi-tx-bus-width = <1>;
+ spi-rx-bus-width = <4>;
+ spi-max-frequency = <40000000>; /* 40MHz */
+ partition@0 {
+ label = "Image Selector";
+ reg = <0x0 0x80000>; /* 512KB */
+ read-only;
+ lock;
+ };
+ partition@80000 {
+ label = "Image Selector Golden";
+ reg = <0x80000 0x80000>; /* 512KB */
+ read-only;
+ lock;
+ };
+ partition@100000 {
+ label = "Persistent Register";
+ reg = <0x100000 0x20000>; /* 128KB */
+ };
+ partition@120000 {
+ label = "Persistent Register Backup";
+ reg = <0x120000 0x20000>; /* 128KB */
+ };
+ partition@140000 {
+ label = "Open_1";
+ reg = <0x140000 0xC0000>; /* 768KB */
+ };
+ partition@200000 {
+ label = "Image A (FSBL, PMU, ATF, U-Boot)";
+ reg = <0x200000 0xD00000>; /* 13MB */
+ };
+ partition@f00000 {
+ label = "ImgSel Image A Catch";
+ reg = <0xF00000 0x80000>; /* 512KB */
+ read-only;
+ lock;
+ };
+ partition@f80000 {
+ label = "Image B (FSBL, PMU, ATF, U-Boot)";
+ reg = <0xF80000 0xD00000>; /* 13MB */
+ };
+ partition@1c80000 {
+ label = "ImgSel Image B Catch";
+ reg = <0x1C80000 0x80000>; /* 512KB */
+ read-only;
+ lock;
+ };
+ partition@1d00000 {
+ label = "Open_2";
+ reg = <0x1D00000 0x100000>; /* 1MB */
+ };
+ partition@1e00000 {
+ label = "Recovery Image";
+ reg = <0x1E00000 0x200000>; /* 2MB */
+ read-only;
+ lock;
+ };
+ partition@2000000 {
+ label = "Recovery Image Backup";
+ reg = <0x2000000 0x200000>; /* 2MB */
+ read-only;
+ lock;
+ };
+ partition@2200000 {
+ label = "U-Boot storage variables";
+ reg = <0x2200000 0x20000>; /* 128KB */
+ };
+ partition@2220000 {
+ label = "U-Boot storage variables backup";
+ reg = <0x2220000 0x20000>; /* 128KB */
+ };
+ partition@2240000 {
+ label = "SHA256";
+ reg = <0x2240000 0x10000>; /* 256B but 64KB sector */
+ read-only;
+ lock;
+ };
+ partition@2250000 {
+ label = "User";
+ reg = <0x2250000 0x1db0000>; /* 29.5 MB */
+ };
+ };
+};
+
+&sdhci0 { /* MIO13-23 - 16GB emmc MTFC16GAPALBH-IT - U133A */
+ status = "okay";
+ non-removable;
+ disable-wp;
+ bus-width = <8>;
+ xlnx,mio-bank = <0>;
+};
+
+&spi1 { /* MIO6, 9-11 */
+ status = "okay";
+ label = "TPM";
+ num-cs = <1>;
+ tpm@0 { /* slm9670 - U144 */
+ compatible = "infineon,slb9670", "tcg,tpm_tis-spi";
+ reg = <0>;
+ spi-max-frequency = <18500000>;
+ };
+};
+
+&i2c1 {
+ status = "okay";
+ clock-frequency = <400000>;
+ scl-gpios = <&gpio 24 GPIO_ACTIVE_HIGH>;
+ sda-gpios = <&gpio 25 GPIO_ACTIVE_HIGH>;
+
+ eeprom: eeprom@50 { /* u46 - also at address 0x58 */
+ compatible = "st,24c64", "atmel,24c64"; /* st m24c64 */
+ reg = <0x50>;
+ /* WP pin EE_WP_EN connected to slg7x644092@68 */
+ };
+
+ eeprom_cc: eeprom@51 { /* required by spec - also at address 0x59 */
+ compatible = "st,24c64", "atmel,24c64"; /* st m24c64 */
+ reg = <0x51>;
+ };
+
+ /* da9062@30 - u170 - also at address 0x31 */
+ /* da9131@33 - u167 */
+ da9131: pmic@33 {
+ compatible = "dlg,da9131";
+ reg = <0x33>;
+ regulators {
+ da9131_buck1: buck1 {
+ regulator-name = "da9131_buck1";
+ regulator-boot-on;
+ regulator-always-on;
+ };
+ da9131_buck2: buck2 {
+ regulator-name = "da9131_buck2";
+ regulator-boot-on;
+ regulator-always-on;
+ };
+ };
+ };
+
+ /* da9130@32 - u166 */
+ da9130: pmic@32 {
+ compatible = "dlg,da9130";
+ reg = <0x32>;
+ regulators {
+ da9130_buck1: buck1 {
+ regulator-name = "da9130_buck1";
+ regulator-boot-on;
+ regulator-always-on;
+ };
+ };
+ };
+
+ /* slg7x644091@70 - u168 NOT accessible due to address conflict with stdp4320 */
+ /*
+ * stdp4320 - u27 FW has below two issues to be fixed in next board revision.
+ * Device acknowledging to addresses 0x5C, 0x5D, 0x70, 0x72, 0x76.
+ * Address conflict with slg7x644091@70 making both the devices NOT accessible.
+ * With the FW fix, stdp4320 should respond to address 0x73 only.
+ */
+ /* slg7x644092@68 - u169 */
+ /* Also connected via JA1C as C23/C24 */
+};
+
+&gpio {
+ status = "okay";
+ gpio-line-names = "QSPI_CLK", "QSPI_DQ1", "QSPI_DQ2", "QSPI_DQ3", "QSPI_DQ0", /* 0 - 4 */
+ "QSPI_CS_B", "SPI_CLK", "LED1", "LED2", "SPI_CS_B", /* 5 - 9 */
+ "SPI_MISO", "SPI_MOSI", "FWUEN", "EMMC_DAT0", "EMMC_DAT1", /* 10 - 14 */
+ "EMMC_DAT2", "EMMC_DAT3", "EMMC_DAT4", "EMMC_DAT5", "EMMC_DAT6", /* 15 - 19 */
+ "EMMC_DAT7", "EMMC_CMD", "EMMC_CLK", "EMMC_RST", "I2C1_SCL", /* 20 - 24 */
+ "I2C1_SDA", "", "", "", "", /* 25 - 29 */
+ "", "", "", "", "", /* 30 - 34 */
+ "", "", "", "", "", /* 35 - 39 */
+ "", "", "", "", "", /* 40 - 44 */
+ "", "", "", "", "", /* 45 - 49 */
+ "", "", "", "", "", /* 50 - 54 */
+ "", "", "", "", "", /* 55 - 59 */
+ "", "", "", "", "", /* 60 - 64 */
+ "", "", "", "", "", /* 65 - 69 */
+ "", "", "", "", "", /* 70 - 74 */
+ "", "", "", /* 75 - 77, MIO end and EMIO start */
+ "", "", /* 78 - 79 */
+ "", "", "", "", "", /* 80 - 84 */
+ "", "", "", "", "", /* 85 - 89 */
+ "", "", "", "", "", /* 90 - 94 */
+ "", "", "", "", "", /* 95 - 99 */
+ "", "", "", "", "", /* 100 - 104 */
+ "", "", "", "", "", /* 105 - 109 */
+ "", "", "", "", "", /* 110 - 114 */
+ "", "", "", "", "", /* 115 - 119 */
+ "", "", "", "", "", /* 120 - 124 */
+ "", "", "", "", "", /* 125 - 129 */
+ "", "", "", "", "", /* 130 - 134 */
+ "", "", "", "", "", /* 135 - 139 */
+ "", "", "", "", "", /* 140 - 144 */
+ "", "", "", "", "", /* 145 - 149 */
+ "", "", "", "", "", /* 150 - 154 */
+ "", "", "", "", "", /* 155 - 159 */
+ "", "", "", "", "", /* 160 - 164 */
+ "", "", "", "", "", /* 165 - 169 */
+ "", "", "", ""; /* 170 - 174 */
+};
--- /dev/null
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * dts file for Xilinx ZynqMP SMK-K26 rev1/B/A
+ *
+ * (C) Copyright 2020 - 2021, Xilinx, Inc.
+ *
+ * Michal Simek <michal.simek@xilinx.com>
+ */
+
+#include "zynqmp-sm-k26-revA.dts"
+
+/ {
+ model = "ZynqMP SMK-K26 Rev1/B/A";
+ compatible = "xlnx,zynqmp-smk-k26-rev1", "xlnx,zynqmp-smk-k26-revB",
+ "xlnx,zynqmp-smk-k26-revA", "xlnx,zynqmp-smk-k26",
+ "xlnx,zynqmp";
+};
+
+&sdhci0 {
+ status = "disabled";
+};
projects / linux.git / commitdiff