ARM: dts: ux500: Split TVK DTSI files in two

The TVK1281618 was made in R1, R2 and R3 variants. The most
commonly used variants are R2 and R3 so split out these to
their own files.

The R3 version has a totally different display than R1 and
R2 and a different set of sensors.

Cc: Stephan Gerhold <stephan@gerhold.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20191126124738.77690-2-linus.walleij@linaro.org

diff --git a/arch/arm/boot/dts/ste-href-tvk1281618-r2.dtsi b/arch/arm/boot/dts/ste-href-tvk1281618-r2.dtsi
new file mode 100644 (file)
index 0000000..e024520
--- /dev/null
+++ b/arch/arm/boot/dts/ste-href-tvk1281618-r2.dtsi
@@ -0,0 +1,79 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * Device Tree for the TVK1281618 R2 UIB
+ */
+
+#include "ste-href-tvk1281618.dtsi"
+
+/ {
+       soc {
+               i2c@80128000 {
+                       lsm303dlh@18 {
+                               /* Accelerometer */
+                               compatible = "st,lsm303dlh-accel";
+                               st,drdy-int-pin = <1>;
+                               drive-open-drain;
+                               reg = <0x18>;
+                               vdd-supply = <&ab8500_ldo_aux1_reg>;
+                               vddio-supply = <&db8500_vsmps2_reg>;
+                               pinctrl-names = "default";
+                               pinctrl-0 = <&accel_tvk_mode>;
+                               /*
+                                * These interrupts cannot be used: the other component
+                                * ST-Micro L3D4200D gyro that is connected to the same lines
+                                * cannot set its DRDY line to open drain, so it cannot be
+                                * shared with other peripherals. The should be defined for
+                                * the falling edge if they could be wired together.
+                                *
+                                * interrupts-extended =
+                                * <&gpio1 0 IRQ_TYPE_EDGE_FALLING>,
+                                * <&gpio2 19 IRQ_TYPE_EDGE_FALLING>;
+                                */
+                       };
+                       lsm303dlh@1e {
+                               /* Magnetometer */
+                               compatible = "st,lsm303dlh-magn";
+                               reg = <0x1e>;
+                               vdd-supply = <&ab8500_ldo_aux1_reg>;
+                               vddio-supply = <&db8500_vsmps2_reg>;
+                               /*
+                                * These interrupts cannot be used: the other component
+                                * ST-Micro L3D4200D gyro that is connected to the same lines
+                                * cannot set its DRDY line to open drain, so it cannot be
+                                * shared with other peripherals. The should be defined for
+                                * the falling edge if they could be wired together.
+                                *
+                                * interrupts-extended =
+                                * <&gpio1 0 IRQ_TYPE_EDGE_FALLING>,
+                                * <&gpio2 19 IRQ_TYPE_EDGE_FALLING>;
+                                */
+                       };
+                       lis331dl@1c {
+                               /* Accelerometer */
+                               compatible = "st,lis331dl-accel";
+                               st,drdy-int-pin = <1>;
+                               reg = <0x1c>;
+                               vdd-supply = <&ab8500_ldo_aux1_reg>;
+                               vddio-supply = <&db8500_vsmps2_reg>;
+                               pinctrl-names = "default";
+                               pinctrl-0 = <&accel_tvk_mode>;
+                               interrupt-parent = <&gpio2>;
+                               /* INT2 would need to be open drain */
+                               interrupts = <18 IRQ_TYPE_EDGE_RISING>,
+                                            <19 IRQ_TYPE_EDGE_RISING>;
+                       };
+               };
+               mcde@a0350000 {
+                       status = "okay";
+
+                       dsi@a0351000 {
+                               panel {
+                                       compatible = "samsung,s6d16d0";
+                                       reg = <0>;
+                                       vdd1-supply = <&ab8500_ldo_aux1_reg>;
+                                       reset-gpios = <&gpio2 1 GPIO_ACTIVE_LOW>;
+                               };
+                       };
+               };
+       };
+};

diff --git a/arch/arm/boot/dts/ste-href-tvk1281618-r3.dtsi b/arch/arm/boot/dts/ste-href-tvk1281618-r3.dtsi
new file mode 100644 (file)
index 0000000..cb3677f
--- /dev/null
+++ b/arch/arm/boot/dts/ste-href-tvk1281618-r3.dtsi
@@ -0,0 +1,58 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * Device Tree for the TVK1281618 R2 UIB
+ */
+
+#include "ste-href-tvk1281618.dtsi"
+
+/ {
+       soc {
+               i2c@80128000 {
+                       /* Marked:
+                        * 129
+                        * M35
+                        * L3GD20
+                        */
+                       l3gd20@6a {
+                               /* Gyroscope */
+                               compatible = "st,l3gd20";
+                               status = "disabled";
+                               st,drdy-int-pin = <1>;
+                               drive-open-drain;
+                               reg = <0x6a>; // 0x6a or 0x6b
+                               vdd-supply = <&ab8500_ldo_aux1_reg>;
+                               vddio-supply = <&db8500_vsmps2_reg>;
+                       };
+                       /*
+                        * Marked:
+                        * 2122
+                        * C3H
+                        * DQEEE
+                        * LIS3DH?
+                        */
+                       lis3dh@18 {
+                               /* Accelerometer */
+                               compatible = "st,lis3dh-accel";
+                               st,drdy-int-pin = <1>;
+                               reg = <0x18>;
+                               vdd-supply = <&ab8500_ldo_aux1_reg>;
+                               vddio-supply = <&db8500_vsmps2_reg>;
+                               pinctrl-names = "default";
+                               pinctrl-0 = <&accel_tvk_mode>;
+                       };
+               };
+
+               mcde@a0350000 {
+                       status = "okay";
+
+                       dsi@a0351000 {
+                               panel {
+                                       compatible = "sony,acx424akp";
+                                       reg = <0>;
+                                       vddi-supply = <&ab8500_ldo_aux1_reg>;
+                                       reset-gpios = <&gpio2 1 GPIO_ACTIVE_LOW>;
+                               };
+                       };
+               };
+       };
+};

diff --git a/arch/arm/boot/dts/ste-href-tvk1281618.dtsi b/arch/arm/boot/dts/ste-href-tvk1281618.dtsi
index 3bafd26b48240f31d8cdff490c2fd73e09ada446..e1dbfae225956220f2a5bd896e37f42f7f0f90b8 100644 (file)
--- a/arch/arm/boot/dts/ste-href-tvk1281618.dtsi
+++ b/arch/arm/boot/dts/ste-href-tvk1281618.dtsi
@@ -2,7 +2,7 @@
 /*
  * Copyright 2012 ST-Ericsson AB
  *
- * Device Tree for the TVK1281618 UIB
+ * Device Tree for the TVK1281618 family of UIBs
  */
 
 #include <dt-bindings/interrupt-controller/irq.h>
@@ -81,62 +81,8 @@
                                };
                        };
                };
-               /* Sensors mounted on this board variant */
+               /* Sensors mounted on all board variants */
                i2c@80128000 {
-                       lsm303dlh@18 {
-                               /* Accelerometer */
-                               compatible = "st,lsm303dlh-accel";
-                               st,drdy-int-pin = <1>;
-                               drive-open-drain;
-                               reg = <0x18>;
-                               vdd-supply = <&ab8500_ldo_aux1_reg>;
-                               vddio-supply = <&db8500_vsmps2_reg>;
-                               pinctrl-names = "default";
-                               pinctrl-0 = <&accel_tvk_mode>;
-                               /*
-                                * These interrupts cannot be used: the other component
-                                * ST-Micro L3D4200D gyro that is connected to the same lines
-                                * cannot set its DRDY line to open drain, so it cannot be
-                                * shared with other peripherals. The should be defined for
-                                * the falling edge if they could be wired together.
-                                *
-                                * interrupts-extended =
-                                * <&gpio1 0 IRQ_TYPE_EDGE_FALLING>,
-                                * <&gpio2 19 IRQ_TYPE_EDGE_FALLING>;
-                                */
-                       };
-                       lsm303dlh@1e {
-                               /* Magnetometer */
-                               compatible = "st,lsm303dlh-magn";
-                               reg = <0x1e>;
-                               vdd-supply = <&ab8500_ldo_aux1_reg>;
-                               vddio-supply = <&db8500_vsmps2_reg>;
-                               /*
-                                * These interrupts cannot be used: the other component
-                                * ST-Micro L3D4200D gyro that is connected to the same lines
-                                * cannot set its DRDY line to open drain, so it cannot be
-                                * shared with other peripherals. The should be defined for
-                                * the falling edge if they could be wired together.
-                                *
-                                * interrupts-extended =
-                                * <&gpio1 0 IRQ_TYPE_EDGE_FALLING>,
-                                * <&gpio2 19 IRQ_TYPE_EDGE_FALLING>;
-                                */
-                       };
-                       lis331dl@1c {
-                               /* Accelerometer */
-                               compatible = "st,lis331dl-accel";
-                               st,drdy-int-pin = <1>;
-                               reg = <0x1c>;
-                               vdd-supply = <&ab8500_ldo_aux1_reg>;
-                               vddio-supply = <&db8500_vsmps2_reg>;
-                               pinctrl-names = "default";
-                               pinctrl-0 = <&accel_tvk_mode>;
-                               interrupt-parent = <&gpio2>;
-                               /* INT2 would need to be open drain */
-                               interrupts = <18 IRQ_TYPE_EDGE_RISING>,
-                                            <19 IRQ_TYPE_EDGE_RISING>;
-                       };
                        ak8974@f {
                                /* Magnetometer */
                                compatible = "asahi-kasei,ak8974";
@@ -268,18 +214,5 @@
                                };
                        };
                };
-
-               mcde@a0350000 {
-                       status = "okay";
-
-                       dsi@a0351000 {
-                               panel {
-                                       compatible = "samsung,s6d16d0";
-                                       reg = <0>;
-                                       vdd1-supply = <&ab8500_ldo_aux1_reg>;
-                                       reset-gpios = <&gpio2 1 GPIO_ACTIVE_LOW>;
-                               };
-                       };
-               };
        };
 };

diff --git a/arch/arm/boot/dts/ste-hrefprev60-tvk.dts b/arch/arm/boot/dts/ste-hrefprev60-tvk.dts
index 8b88c91dca6c0bcb946f93620197073855690356..142f5475521f806742dd1fdfbbbbcd5a452f7f32 100644 (file)
--- a/arch/arm/boot/dts/ste-hrefprev60-tvk.dts
+++ b/arch/arm/boot/dts/ste-hrefprev60-tvk.dts
@@ -6,7 +6,7 @@
 /dts-v1/;
 #include "ste-db8500.dtsi"
 #include "ste-hrefprev60.dtsi"
-#include "ste-href-tvk1281618.dtsi"
+#include "ste-href-tvk1281618-r2.dtsi"
 
 / {
        model = "ST-Ericsson HREF (pre-v60) and TVK1281618 UIB";

diff --git a/arch/arm/boot/dts/ste-hrefv60plus-tvk.dts b/arch/arm/boot/dts/ste-hrefv60plus-tvk.dts
index b31e43d5ff899fad899d6cf0395e4ae73f65de00..5d4b8245f02c089ad02f0e5b3633cea366dd0e48 100644 (file)
--- a/arch/arm/boot/dts/ste-hrefv60plus-tvk.dts
+++ b/arch/arm/boot/dts/ste-hrefv60plus-tvk.dts
@@ -8,7 +8,7 @@
 /dts-v1/;
 #include "ste-db8500.dtsi"
 #include "ste-hrefv60plus.dtsi"
-#include "ste-href-tvk1281618.dtsi"
+#include "ste-href-tvk1281618-r2.dtsi"
 
 / {
        model = "ST-Ericsson HREF (v60+) and TVK1281618 UIB";