sysfs notes:
The ThinkLight sysfs interface is documented by the LED class
-documentation, in Documentation/leds/leds-class.txt. The ThinkLight LED name
+documentation, in Documentation/leds/leds-class.rst. The ThinkLight LED name
is "tpacpi::thinklight".
Due to limitations in the sysfs LED class, if the status of the ThinkLight
sysfs notes:
The ThinkPad LED sysfs interface is described in detail by the LED class
-documentation, in Documentation/leds/leds-class.txt.
+documentation, in Documentation/leds/leds-class.rst.
The LEDs are named (in LED ID order, from 0 to 12):
"tpacpi::power", "tpacpi:orange:batt", "tpacpi:green:batt",
--- /dev/null
+:orphan:
+
+====
+LEDs
+====
+
+.. toctree::
+ :maxdepth: 1
+
+ leds-class
+ leds-class-flash
+ ledtrig-oneshot
+ ledtrig-transient
+ ledtrig-usbport
+
+ uleds
+
+ leds-blinkm
+ leds-lm3556
+ leds-lp3944
+ leds-lp5521
+ leds-lp5523
+ leds-lp5562
+ leds-lp55xx
+ leds-mlxcpld
--- /dev/null
+==================
+Leds BlinkM driver
+==================
+
+The leds-blinkm driver supports the devices of the BlinkM family.
+
+They are RGB-LED modules driven by a (AT)tiny microcontroller and
+communicate through I2C. The default address of these modules is
+0x09 but this can be changed through a command. By this you could
+dasy-chain up to 127 BlinkMs on an I2C bus.
+
+The device accepts RGB and HSB color values through separate commands.
+Also you can store blinking sequences as "scripts" in
+the controller and run them. Also fading is an option.
+
+The interface this driver provides is 2-fold:
+
+a) LED class interface for use with triggers
+############################################
+
+The registration follows the scheme::
+
+ blinkm-<i2c-bus-nr>-<i2c-device-nr>-<color>
+
+ $ ls -h /sys/class/leds/blinkm-6-*
+ /sys/class/leds/blinkm-6-9-blue:
+ brightness device max_brightness power subsystem trigger uevent
+
+ /sys/class/leds/blinkm-6-9-green:
+ brightness device max_brightness power subsystem trigger uevent
+
+ /sys/class/leds/blinkm-6-9-red:
+ brightness device max_brightness power subsystem trigger uevent
+
+(same is /sys/bus/i2c/devices/6-0009/leds)
+
+We can control the colors separated into red, green and blue and
+assign triggers on each color.
+
+E.g.::
+
+ $ cat blinkm-6-9-blue/brightness
+ 05
+
+ $ echo 200 > blinkm-6-9-blue/brightness
+ $
+
+ $ modprobe ledtrig-heartbeat
+ $ echo heartbeat > blinkm-6-9-green/trigger
+ $
+
+
+b) Sysfs group to control rgb, fade, hsb, scripts ...
+#####################################################
+
+This extended interface is available as folder blinkm
+in the sysfs folder of the I2C device.
+E.g. below /sys/bus/i2c/devices/6-0009/blinkm
+
+ $ ls -h /sys/bus/i2c/devices/6-0009/blinkm/
+ blue green red test
+
+Currently supported is just setting red, green, blue
+and a test sequence.
+
+E.g.::
+
+ $ cat *
+ 00
+ 00
+ 00
+ #Write into test to start test sequence!#
+
+ $ echo 1 > test
+ $
+
+ $ echo 255 > red
+ $
+
+
+
+as of 6/2012
+
+dl9pf <at> gmx <dot> de
+++ /dev/null
-The leds-blinkm driver supports the devices of the BlinkM family.
-
-They are RGB-LED modules driven by a (AT)tiny microcontroller and
-communicate through I2C. The default address of these modules is
-0x09 but this can be changed through a command. By this you could
-dasy-chain up to 127 BlinkMs on an I2C bus.
-
-The device accepts RGB and HSB color values through separate commands.
-Also you can store blinking sequences as "scripts" in
-the controller and run them. Also fading is an option.
-
-The interface this driver provides is 2-fold:
-
-a) LED class interface for use with triggers
-############################################
-
-The registration follows the scheme:
-blinkm-<i2c-bus-nr>-<i2c-device-nr>-<color>
-
-$ ls -h /sys/class/leds/blinkm-6-*
-/sys/class/leds/blinkm-6-9-blue:
-brightness device max_brightness power subsystem trigger uevent
-
-/sys/class/leds/blinkm-6-9-green:
-brightness device max_brightness power subsystem trigger uevent
-
-/sys/class/leds/blinkm-6-9-red:
-brightness device max_brightness power subsystem trigger uevent
-
-(same is /sys/bus/i2c/devices/6-0009/leds)
-
-We can control the colors separated into red, green and blue and
-assign triggers on each color.
-
-E.g.:
-
-$ cat blinkm-6-9-blue/brightness
-05
-
-$ echo 200 > blinkm-6-9-blue/brightness
-$
-
-$ modprobe ledtrig-heartbeat
-$ echo heartbeat > blinkm-6-9-green/trigger
-$
-
-
-b) Sysfs group to control rgb, fade, hsb, scripts ...
-#####################################################
-
-This extended interface is available as folder blinkm
-in the sysfs folder of the I2C device.
-E.g. below /sys/bus/i2c/devices/6-0009/blinkm
-
-$ ls -h /sys/bus/i2c/devices/6-0009/blinkm/
-blue green red test
-
-Currently supported is just setting red, green, blue
-and a test sequence.
-
-E.g.:
-
-$ cat *
-00
-00
-00
-#Write into test to start test sequence!#
-
-$ echo 1 > test
-$
-
-$ echo 255 > red
-$
-
-
-
-as of 6/2012
-
-dl9pf <at> gmx <dot> de
-
--- /dev/null
+==============================
+Flash LED handling under Linux
+==============================
+
+Some LED devices provide two modes - torch and flash. In the LED subsystem
+those modes are supported by LED class (see Documentation/leds/leds-class.rst)
+and LED Flash class respectively. The torch mode related features are enabled
+by default and the flash ones only if a driver declares it by setting
+LED_DEV_CAP_FLASH flag.
+
+In order to enable the support for flash LEDs CONFIG_LEDS_CLASS_FLASH symbol
+must be defined in the kernel config. A LED Flash class driver must be
+registered in the LED subsystem with led_classdev_flash_register function.
+
+Following sysfs attributes are exposed for controlling flash LED devices:
+(see Documentation/ABI/testing/sysfs-class-led-flash)
+
+ - flash_brightness
+ - max_flash_brightness
+ - flash_timeout
+ - max_flash_timeout
+ - flash_strobe
+ - flash_fault
+
+
+V4L2 flash wrapper for flash LEDs
+=================================
+
+A LED subsystem driver can be controlled also from the level of VideoForLinux2
+subsystem. In order to enable this CONFIG_V4L2_FLASH_LED_CLASS symbol has to
+be defined in the kernel config.
+
+The driver must call the v4l2_flash_init function to get registered in the
+V4L2 subsystem. The function takes six arguments:
+
+- dev:
+ flash device, e.g. an I2C device
+- of_node:
+ of_node of the LED, may be NULL if the same as device's
+- fled_cdev:
+ LED flash class device to wrap
+- iled_cdev:
+ LED flash class device representing indicator LED associated with
+ fled_cdev, may be NULL
+- ops:
+ V4L2 specific ops
+
+ * external_strobe_set
+ defines the source of the flash LED strobe -
+ V4L2_CID_FLASH_STROBE control or external source, typically
+ a sensor, which makes it possible to synchronise the flash
+ strobe start with exposure start,
+ * intensity_to_led_brightness and led_brightness_to_intensity
+ perform
+ enum led_brightness <-> V4L2 intensity conversion in a device
+ specific manner - they can be used for devices with non-linear
+ LED current scale.
+- config:
+ configuration for V4L2 Flash sub-device
+
+ * dev_name
+ the name of the media entity, unique in the system,
+ * flash_faults
+ bitmask of flash faults that the LED flash class
+ device can report; corresponding LED_FAULT* bit definitions are
+ available in <linux/led-class-flash.h>,
+ * torch_intensity
+ constraints for the LED in TORCH mode
+ in microamperes,
+ * indicator_intensity
+ constraints for the indicator LED
+ in microamperes,
+ * has_external_strobe
+ determines whether the flash strobe source
+ can be switched to external,
+
+On remove the v4l2_flash_release function has to be called, which takes one
+argument - struct v4l2_flash pointer returned previously by v4l2_flash_init.
+This function can be safely called with NULL or error pointer argument.
+
+Please refer to drivers/leds/leds-max77693.c for an exemplary usage of the
+v4l2 flash wrapper.
+
+Once the V4L2 sub-device is registered by the driver which created the Media
+controller device, the sub-device node acts just as a node of a native V4L2
+flash API device would. The calls are simply routed to the LED flash API.
+
+Opening the V4L2 flash sub-device makes the LED subsystem sysfs interface
+unavailable. The interface is re-enabled after the V4L2 flash sub-device
+is closed.
+++ /dev/null
-
-Flash LED handling under Linux
-==============================
-
-Some LED devices provide two modes - torch and flash. In the LED subsystem
-those modes are supported by LED class (see Documentation/leds/leds-class.txt)
-and LED Flash class respectively. The torch mode related features are enabled
-by default and the flash ones only if a driver declares it by setting
-LED_DEV_CAP_FLASH flag.
-
-In order to enable the support for flash LEDs CONFIG_LEDS_CLASS_FLASH symbol
-must be defined in the kernel config. A LED Flash class driver must be
-registered in the LED subsystem with led_classdev_flash_register function.
-
-Following sysfs attributes are exposed for controlling flash LED devices:
-(see Documentation/ABI/testing/sysfs-class-led-flash)
- - flash_brightness
- - max_flash_brightness
- - flash_timeout
- - max_flash_timeout
- - flash_strobe
- - flash_fault
-
-
-V4L2 flash wrapper for flash LEDs
-=================================
-
-A LED subsystem driver can be controlled also from the level of VideoForLinux2
-subsystem. In order to enable this CONFIG_V4L2_FLASH_LED_CLASS symbol has to
-be defined in the kernel config.
-
-The driver must call the v4l2_flash_init function to get registered in the
-V4L2 subsystem. The function takes six arguments:
-- dev : flash device, e.g. an I2C device
-- of_node : of_node of the LED, may be NULL if the same as device's
-- fled_cdev : LED flash class device to wrap
-- iled_cdev : LED flash class device representing indicator LED associated with
- fled_cdev, may be NULL
-- ops : V4L2 specific ops
- * external_strobe_set - defines the source of the flash LED strobe -
- V4L2_CID_FLASH_STROBE control or external source, typically
- a sensor, which makes it possible to synchronise the flash
- strobe start with exposure start,
- * intensity_to_led_brightness and led_brightness_to_intensity - perform
- enum led_brightness <-> V4L2 intensity conversion in a device
- specific manner - they can be used for devices with non-linear
- LED current scale.
-- config : configuration for V4L2 Flash sub-device
- * dev_name - the name of the media entity, unique in the system,
- * flash_faults - bitmask of flash faults that the LED flash class
- device can report; corresponding LED_FAULT* bit definitions are
- available in <linux/led-class-flash.h>,
- * torch_intensity - constraints for the LED in TORCH mode
- in microamperes,
- * indicator_intensity - constraints for the indicator LED
- in microamperes,
- * has_external_strobe - determines whether the flash strobe source
- can be switched to external,
-
-On remove the v4l2_flash_release function has to be called, which takes one
-argument - struct v4l2_flash pointer returned previously by v4l2_flash_init.
-This function can be safely called with NULL or error pointer argument.
-
-Please refer to drivers/leds/leds-max77693.c for an exemplary usage of the
-v4l2 flash wrapper.
-
-Once the V4L2 sub-device is registered by the driver which created the Media
-controller device, the sub-device node acts just as a node of a native V4L2
-flash API device would. The calls are simply routed to the LED flash API.
-
-Opening the V4L2 flash sub-device makes the LED subsystem sysfs interface
-unavailable. The interface is re-enabled after the V4L2 flash sub-device
-is closed.
--- /dev/null
+========================
+LED handling under Linux
+========================
+
+In its simplest form, the LED class just allows control of LEDs from
+userspace. LEDs appear in /sys/class/leds/. The maximum brightness of the
+LED is defined in max_brightness file. The brightness file will set the brightness
+of the LED (taking a value 0-max_brightness). Most LEDs don't have hardware
+brightness support so will just be turned on for non-zero brightness settings.
+
+The class also introduces the optional concept of an LED trigger. A trigger
+is a kernel based source of led events. Triggers can either be simple or
+complex. A simple trigger isn't configurable and is designed to slot into
+existing subsystems with minimal additional code. Examples are the disk-activity,
+nand-disk and sharpsl-charge triggers. With led triggers disabled, the code
+optimises away.
+
+Complex triggers while available to all LEDs have LED specific
+parameters and work on a per LED basis. The timer trigger is an example.
+The timer trigger will periodically change the LED brightness between
+LED_OFF and the current brightness setting. The "on" and "off" time can
+be specified via /sys/class/leds/<device>/delay_{on,off} in milliseconds.
+You can change the brightness value of a LED independently of the timer
+trigger. However, if you set the brightness value to LED_OFF it will
+also disable the timer trigger.
+
+You can change triggers in a similar manner to the way an IO scheduler
+is chosen (via /sys/class/leds/<device>/trigger). Trigger specific
+parameters can appear in /sys/class/leds/<device> once a given trigger is
+selected.
+
+
+Design Philosophy
+=================
+
+The underlying design philosophy is simplicity. LEDs are simple devices
+and the aim is to keep a small amount of code giving as much functionality
+as possible. Please keep this in mind when suggesting enhancements.
+
+
+LED Device Naming
+=================
+
+Is currently of the form:
+
+ "devicename:colour:function"
+
+There have been calls for LED properties such as colour to be exported as
+individual led class attributes. As a solution which doesn't incur as much
+overhead, I suggest these become part of the device name. The naming scheme
+above leaves scope for further attributes should they be needed. If sections
+of the name don't apply, just leave that section blank.
+
+
+Brightness setting API
+======================
+
+LED subsystem core exposes following API for setting brightness:
+
+ - led_set_brightness:
+ it is guaranteed not to sleep, passing LED_OFF stops
+ blinking,
+
+ - led_set_brightness_sync:
+ for use cases when immediate effect is desired -
+ it can block the caller for the time required for accessing
+ device registers and can sleep, passing LED_OFF stops hardware
+ blinking, returns -EBUSY if software blink fallback is enabled.
+
+
+LED registration API
+====================
+
+A driver wanting to register a LED classdev for use by other drivers /
+userspace needs to allocate and fill a led_classdev struct and then call
+`[devm_]led_classdev_register`. If the non devm version is used the driver
+must call led_classdev_unregister from its remove function before
+free-ing the led_classdev struct.
+
+If the driver can detect hardware initiated brightness changes and thus
+wants to have a brightness_hw_changed attribute then the LED_BRIGHT_HW_CHANGED
+flag must be set in flags before registering. Calling
+led_classdev_notify_brightness_hw_changed on a classdev not registered with
+the LED_BRIGHT_HW_CHANGED flag is a bug and will trigger a WARN_ON.
+
+Hardware accelerated blink of LEDs
+==================================
+
+Some LEDs can be programmed to blink without any CPU interaction. To
+support this feature, a LED driver can optionally implement the
+blink_set() function (see <linux/leds.h>). To set an LED to blinking,
+however, it is better to use the API function led_blink_set(), as it
+will check and implement software fallback if necessary.
+
+To turn off blinking, use the API function led_brightness_set()
+with brightness value LED_OFF, which should stop any software
+timers that may have been required for blinking.
+
+The blink_set() function should choose a user friendly blinking value
+if it is called with `*delay_on==0` && `*delay_off==0` parameters. In this
+case the driver should give back the chosen value through delay_on and
+delay_off parameters to the leds subsystem.
+
+Setting the brightness to zero with brightness_set() callback function
+should completely turn off the LED and cancel the previously programmed
+hardware blinking function, if any.
+
+
+Known Issues
+============
+
+The LED Trigger core cannot be a module as the simple trigger functions
+would cause nightmare dependency issues. I see this as a minor issue
+compared to the benefits the simple trigger functionality brings. The
+rest of the LED subsystem can be modular.
+
+
+Future Development
+==================
+
+At the moment, a trigger can't be created specifically for a single LED.
+There are a number of cases where a trigger might only be mappable to a
+particular LED (ACPI?). The addition of triggers provided by the LED driver
+should cover this option and be possible to add without breaking the
+current interface.
+++ /dev/null
-
-LED handling under Linux
-========================
-
-In its simplest form, the LED class just allows control of LEDs from
-userspace. LEDs appear in /sys/class/leds/. The maximum brightness of the
-LED is defined in max_brightness file. The brightness file will set the brightness
-of the LED (taking a value 0-max_brightness). Most LEDs don't have hardware
-brightness support so will just be turned on for non-zero brightness settings.
-
-The class also introduces the optional concept of an LED trigger. A trigger
-is a kernel based source of led events. Triggers can either be simple or
-complex. A simple trigger isn't configurable and is designed to slot into
-existing subsystems with minimal additional code. Examples are the disk-activity,
-nand-disk and sharpsl-charge triggers. With led triggers disabled, the code
-optimises away.
-
-Complex triggers while available to all LEDs have LED specific
-parameters and work on a per LED basis. The timer trigger is an example.
-The timer trigger will periodically change the LED brightness between
-LED_OFF and the current brightness setting. The "on" and "off" time can
-be specified via /sys/class/leds/<device>/delay_{on,off} in milliseconds.
-You can change the brightness value of a LED independently of the timer
-trigger. However, if you set the brightness value to LED_OFF it will
-also disable the timer trigger.
-
-You can change triggers in a similar manner to the way an IO scheduler
-is chosen (via /sys/class/leds/<device>/trigger). Trigger specific
-parameters can appear in /sys/class/leds/<device> once a given trigger is
-selected.
-
-
-Design Philosophy
-=================
-
-The underlying design philosophy is simplicity. LEDs are simple devices
-and the aim is to keep a small amount of code giving as much functionality
-as possible. Please keep this in mind when suggesting enhancements.
-
-
-LED Device Naming
-=================
-
-Is currently of the form:
-
-"devicename:colour:function"
-
-There have been calls for LED properties such as colour to be exported as
-individual led class attributes. As a solution which doesn't incur as much
-overhead, I suggest these become part of the device name. The naming scheme
-above leaves scope for further attributes should they be needed. If sections
-of the name don't apply, just leave that section blank.
-
-
-Brightness setting API
-======================
-
-LED subsystem core exposes following API for setting brightness:
-
- - led_set_brightness : it is guaranteed not to sleep, passing LED_OFF stops
- blinking,
- - led_set_brightness_sync : for use cases when immediate effect is desired -
- it can block the caller for the time required for accessing
- device registers and can sleep, passing LED_OFF stops hardware
- blinking, returns -EBUSY if software blink fallback is enabled.
-
-
-LED registration API
-====================
-
-A driver wanting to register a LED classdev for use by other drivers /
-userspace needs to allocate and fill a led_classdev struct and then call
-[devm_]led_classdev_register. If the non devm version is used the driver
-must call led_classdev_unregister from its remove function before
-free-ing the led_classdev struct.
-
-If the driver can detect hardware initiated brightness changes and thus
-wants to have a brightness_hw_changed attribute then the LED_BRIGHT_HW_CHANGED
-flag must be set in flags before registering. Calling
-led_classdev_notify_brightness_hw_changed on a classdev not registered with
-the LED_BRIGHT_HW_CHANGED flag is a bug and will trigger a WARN_ON.
-
-Hardware accelerated blink of LEDs
-==================================
-
-Some LEDs can be programmed to blink without any CPU interaction. To
-support this feature, a LED driver can optionally implement the
-blink_set() function (see <linux/leds.h>). To set an LED to blinking,
-however, it is better to use the API function led_blink_set(), as it
-will check and implement software fallback if necessary.
-
-To turn off blinking, use the API function led_brightness_set()
-with brightness value LED_OFF, which should stop any software
-timers that may have been required for blinking.
-
-The blink_set() function should choose a user friendly blinking value
-if it is called with *delay_on==0 && *delay_off==0 parameters. In this
-case the driver should give back the chosen value through delay_on and
-delay_off parameters to the leds subsystem.
-
-Setting the brightness to zero with brightness_set() callback function
-should completely turn off the LED and cancel the previously programmed
-hardware blinking function, if any.
-
-
-Known Issues
-============
-
-The LED Trigger core cannot be a module as the simple trigger functions
-would cause nightmare dependency issues. I see this as a minor issue
-compared to the benefits the simple trigger functionality brings. The
-rest of the LED subsystem can be modular.
-
-
-Future Development
-==================
-
-At the moment, a trigger can't be created specifically for a single LED.
-There are a number of cases where a trigger might only be mappable to a
-particular LED (ACPI?). The addition of triggers provided by the LED driver
-should cover this option and be possible to add without breaking the
-current interface.
--- /dev/null
+========================
+Kernel driver for lm3556
+========================
+
+* Texas Instrument:
+ 1.5 A Synchronous Boost LED Flash Driver w/ High-Side Current Source
+* Datasheet: http://www.national.com/ds/LM/LM3556.pdf
+
+Authors:
+ - Daniel Jeong
+
+ Contact:Daniel Jeong(daniel.jeong-at-ti.com, gshark.jeong-at-gmail.com)
+
+Description
+-----------
+There are 3 functions in LM3556, Flash, Torch and Indicator.
+
+Flash Mode
+^^^^^^^^^^
+
+In Flash Mode, the LED current source(LED) provides 16 target current levels
+from 93.75 mA to 1500 mA.The Flash currents are adjusted via the CURRENT
+CONTROL REGISTER(0x09).Flash mode is activated by the ENABLE REGISTER(0x0A),
+or by pulling the STROBE pin HIGH.
+
+LM3556 Flash can be controlled through sys/class/leds/flash/brightness file
+
+* if STROBE pin is enabled, below example control brightness only, and
+ ON / OFF will be controlled by STROBE pin.
+
+Flash Example:
+
+OFF::
+
+ #echo 0 > sys/class/leds/flash/brightness
+
+93.75 mA::
+
+ #echo 1 > sys/class/leds/flash/brightness
+
+...
+
+1500 mA::
+
+ #echo 16 > sys/class/leds/flash/brightness
+
+Torch Mode
+^^^^^^^^^^
+
+In Torch Mode, the current source(LED) is programmed via the CURRENT CONTROL
+REGISTER(0x09).Torch Mode is activated by the ENABLE REGISTER(0x0A) or by the
+hardware TORCH input.
+
+LM3556 torch can be controlled through sys/class/leds/torch/brightness file.
+* if TORCH pin is enabled, below example control brightness only,
+and ON / OFF will be controlled by TORCH pin.
+
+Torch Example:
+
+OFF::
+
+ #echo 0 > sys/class/leds/torch/brightness
+
+46.88 mA::
+
+ #echo 1 > sys/class/leds/torch/brightness
+
+...
+
+375 mA::
+
+ #echo 8 > sys/class/leds/torch/brightness
+
+Indicator Mode
+^^^^^^^^^^^^^^
+
+Indicator pattern can be set through sys/class/leds/indicator/pattern file,
+and 4 patterns are pre-defined in indicator_pattern array.
+
+According to N-lank, Pulse time and N Period values, different pattern wiill
+be generated.If you want new patterns for your own device, change
+indicator_pattern array with your own values and INDIC_PATTERN_SIZE.
+
+Please refer datasheet for more detail about N-Blank, Pulse time and N Period.
+
+Indicator pattern example:
+
+pattern 0::
+
+ #echo 0 > sys/class/leds/indicator/pattern
+
+...
+
+pattern 3::
+
+ #echo 3 > sys/class/leds/indicator/pattern
+
+Indicator brightness can be controlled through
+sys/class/leds/indicator/brightness file.
+
+Example:
+
+OFF::
+
+ #echo 0 > sys/class/leds/indicator/brightness
+
+5.86 mA::
+
+ #echo 1 > sys/class/leds/indicator/brightness
+
+...
+
+46.875mA::
+
+ #echo 8 > sys/class/leds/indicator/brightness
+
+Notes
+-----
+Driver expects it is registered using the i2c_board_info mechanism.
+To register the chip at address 0x63 on specific adapter, set the platform data
+according to include/linux/platform_data/leds-lm3556.h, set the i2c board info
+
+Example::
+
+ static struct i2c_board_info board_i2c_ch4[] __initdata = {
+ {
+ I2C_BOARD_INFO(LM3556_NAME, 0x63),
+ .platform_data = &lm3556_pdata,
+ },
+ };
+
+and register it in the platform init function
+
+Example::
+
+ board_register_i2c_bus(4, 400,
+ board_i2c_ch4, ARRAY_SIZE(board_i2c_ch4));
+++ /dev/null
-Kernel driver for lm3556
-========================
-
-*Texas Instrument:
- 1.5 A Synchronous Boost LED Flash Driver w/ High-Side Current Source
-* Datasheet: http://www.national.com/ds/LM/LM3556.pdf
-
-Authors:
- Daniel Jeong
- Contact:Daniel Jeong(daniel.jeong-at-ti.com, gshark.jeong-at-gmail.com)
-
-Description
------------
-There are 3 functions in LM3556, Flash, Torch and Indicator.
-
-FLASH MODE
-In Flash Mode, the LED current source(LED) provides 16 target current levels
-from 93.75 mA to 1500 mA.The Flash currents are adjusted via the CURRENT
-CONTROL REGISTER(0x09).Flash mode is activated by the ENABLE REGISTER(0x0A),
-or by pulling the STROBE pin HIGH.
-LM3556 Flash can be controlled through sys/class/leds/flash/brightness file
-* if STROBE pin is enabled, below example control brightness only, and
-ON / OFF will be controlled by STROBE pin.
-
-Flash Example:
-OFF : #echo 0 > sys/class/leds/flash/brightness
-93.75 mA: #echo 1 > sys/class/leds/flash/brightness
-... .....
-1500 mA: #echo 16 > sys/class/leds/flash/brightness
-
-TORCH MODE
-In Torch Mode, the current source(LED) is programmed via the CURRENT CONTROL
-REGISTER(0x09).Torch Mode is activated by the ENABLE REGISTER(0x0A) or by the
-hardware TORCH input.
-LM3556 torch can be controlled through sys/class/leds/torch/brightness file.
-* if TORCH pin is enabled, below example control brightness only,
-and ON / OFF will be controlled by TORCH pin.
-
-Torch Example:
-OFF : #echo 0 > sys/class/leds/torch/brightness
-46.88 mA: #echo 1 > sys/class/leds/torch/brightness
-... .....
-375 mA : #echo 8 > sys/class/leds/torch/brightness
-
-INDICATOR MODE
-Indicator pattern can be set through sys/class/leds/indicator/pattern file,
-and 4 patterns are pre-defined in indicator_pattern array.
-According to N-lank, Pulse time and N Period values, different pattern wiill
-be generated.If you want new patterns for your own device, change
-indicator_pattern array with your own values and INDIC_PATTERN_SIZE.
-Please refer datasheet for more detail about N-Blank, Pulse time and N Period.
-
-Indicator pattern example:
-pattern 0: #echo 0 > sys/class/leds/indicator/pattern
-....
-pattern 3: #echo 3 > sys/class/leds/indicator/pattern
-
-Indicator brightness can be controlled through
-sys/class/leds/indicator/brightness file.
-
-Example:
-OFF : #echo 0 > sys/class/leds/indicator/brightness
-5.86 mA : #echo 1 > sys/class/leds/indicator/brightness
-........
-46.875mA : #echo 8 > sys/class/leds/indicator/brightness
-
-Notes
------
-Driver expects it is registered using the i2c_board_info mechanism.
-To register the chip at address 0x63 on specific adapter, set the platform data
-according to include/linux/platform_data/leds-lm3556.h, set the i2c board info
-
-Example:
- static struct i2c_board_info board_i2c_ch4[] __initdata = {
- {
- I2C_BOARD_INFO(LM3556_NAME, 0x63),
- .platform_data = &lm3556_pdata,
- },
- };
-
-and register it in the platform init function
-
-Example:
- board_register_i2c_bus(4, 400,
- board_i2c_ch4, ARRAY_SIZE(board_i2c_ch4));
--- /dev/null
+====================
+Kernel driver lp3944
+====================
+
+ * National Semiconductor LP3944 Fun-light Chip
+
+ Prefix: 'lp3944'
+
+ Addresses scanned: None (see the Notes section below)
+
+ Datasheet:
+
+ Publicly available at the National Semiconductor website
+ http://www.national.com/pf/LP/LP3944.html
+
+Authors:
+ Antonio Ospite <ospite@studenti.unina.it>
+
+
+Description
+-----------
+The LP3944 is a helper chip that can drive up to 8 leds, with two programmable
+DIM modes; it could even be used as a gpio expander but this driver assumes it
+is used as a led controller.
+
+The DIM modes are used to set _blink_ patterns for leds, the pattern is
+specified supplying two parameters:
+
+ - period:
+ from 0s to 1.6s
+ - duty cycle:
+ percentage of the period the led is on, from 0 to 100
+
+Setting a led in DIM0 or DIM1 mode makes it blink according to the pattern.
+See the datasheet for details.
+
+LP3944 can be found on Motorola A910 smartphone, where it drives the rgb
+leds, the camera flash light and the lcds power.
+
+
+Notes
+-----
+The chip is used mainly in embedded contexts, so this driver expects it is
+registered using the i2c_board_info mechanism.
+
+To register the chip at address 0x60 on adapter 0, set the platform data
+according to include/linux/leds-lp3944.h, set the i2c board info::
+
+ static struct i2c_board_info a910_i2c_board_info[] __initdata = {
+ {
+ I2C_BOARD_INFO("lp3944", 0x60),
+ .platform_data = &a910_lp3944_leds,
+ },
+ };
+
+and register it in the platform init function::
+
+ i2c_register_board_info(0, a910_i2c_board_info,
+ ARRAY_SIZE(a910_i2c_board_info));
+++ /dev/null
-Kernel driver lp3944
-====================
-
- * National Semiconductor LP3944 Fun-light Chip
- Prefix: 'lp3944'
- Addresses scanned: None (see the Notes section below)
- Datasheet: Publicly available at the National Semiconductor website
- http://www.national.com/pf/LP/LP3944.html
-
-Authors:
- Antonio Ospite <ospite@studenti.unina.it>
-
-
-Description
------------
-The LP3944 is a helper chip that can drive up to 8 leds, with two programmable
-DIM modes; it could even be used as a gpio expander but this driver assumes it
-is used as a led controller.
-
-The DIM modes are used to set _blink_ patterns for leds, the pattern is
-specified supplying two parameters:
- - period: from 0s to 1.6s
- - duty cycle: percentage of the period the led is on, from 0 to 100
-
-Setting a led in DIM0 or DIM1 mode makes it blink according to the pattern.
-See the datasheet for details.
-
-LP3944 can be found on Motorola A910 smartphone, where it drives the rgb
-leds, the camera flash light and the lcds power.
-
-
-Notes
------
-The chip is used mainly in embedded contexts, so this driver expects it is
-registered using the i2c_board_info mechanism.
-
-To register the chip at address 0x60 on adapter 0, set the platform data
-according to include/linux/leds-lp3944.h, set the i2c board info:
-
- static struct i2c_board_info a910_i2c_board_info[] __initdata = {
- {
- I2C_BOARD_INFO("lp3944", 0x60),
- .platform_data = &a910_lp3944_leds,
- },
- };
-
-and register it in the platform init function
-
- i2c_register_board_info(0, a910_i2c_board_info,
- ARRAY_SIZE(a910_i2c_board_info));
--- /dev/null
+========================
+Kernel driver for lp5521
+========================
+
+* National Semiconductor LP5521 led driver chip
+* Datasheet: http://www.national.com/pf/LP/LP5521.html
+
+Authors: Mathias Nyman, Yuri Zaporozhets, Samu Onkalo
+
+Contact: Samu Onkalo (samu.p.onkalo-at-nokia.com)
+
+Description
+-----------
+
+LP5521 can drive up to 3 channels. Leds can be controlled directly via
+the led class control interface. Channels have generic names:
+lp5521:channelx, where x is 0 .. 2
+
+All three channels can be also controlled using the engine micro programs.
+More details of the instructions can be found from the public data sheet.
+
+LP5521 has the internal program memory for running various LED patterns.
+There are two ways to run LED patterns.
+
+1) Legacy interface - enginex_mode and enginex_load
+ Control interface for the engines:
+
+ x is 1 .. 3
+
+ enginex_mode:
+ disabled, load, run
+ enginex_load:
+ store program (visible only in engine load mode)
+
+ Example (start to blink the channel 2 led)::
+
+ cd /sys/class/leds/lp5521:channel2/device
+ echo "load" > engine3_mode
+ echo "037f4d0003ff6000" > engine3_load
+ echo "run" > engine3_mode
+
+ To stop the engine::
+
+ echo "disabled" > engine3_mode
+
+2) Firmware interface - LP55xx common interface
+
+For the details, please refer to 'firmware' section in leds-lp55xx.txt
+
+sysfs contains a selftest entry.
+
+The test communicates with the chip and checks that
+the clock mode is automatically set to the requested one.
+
+Each channel has its own led current settings.
+
+- /sys/class/leds/lp5521:channel0/led_current - RW
+- /sys/class/leds/lp5521:channel0/max_current - RO
+
+Format: 10x mA i.e 10 means 1.0 mA
+
+example platform data::
+
+ static struct lp55xx_led_config lp5521_led_config[] = {
+ {
+ .name = "red",
+ .chan_nr = 0,
+ .led_current = 50,
+ .max_current = 130,
+ }, {
+ .name = "green",
+ .chan_nr = 1,
+ .led_current = 0,
+ .max_current = 130,
+ }, {
+ .name = "blue",
+ .chan_nr = 2,
+ .led_current = 0,
+ .max_current = 130,
+ }
+ };
+
+ static int lp5521_setup(void)
+ {
+ /* setup HW resources */
+ }
+
+ static void lp5521_release(void)
+ {
+ /* Release HW resources */
+ }
+
+ static void lp5521_enable(bool state)
+ {
+ /* Control of chip enable signal */
+ }
+
+ static struct lp55xx_platform_data lp5521_platform_data = {
+ .led_config = lp5521_led_config,
+ .num_channels = ARRAY_SIZE(lp5521_led_config),
+ .clock_mode = LP55XX_CLOCK_EXT,
+ .setup_resources = lp5521_setup,
+ .release_resources = lp5521_release,
+ .enable = lp5521_enable,
+ };
+
+Note:
+ chan_nr can have values between 0 and 2.
+ The name of each channel can be configurable.
+ If the name field is not defined, the default name will be set to 'xxxx:channelN'
+ (XXXX : pdata->label or i2c client name, N : channel number)
+
+
+If the current is set to 0 in the platform data, that channel is
+disabled and it is not visible in the sysfs.
+++ /dev/null
-Kernel driver for lp5521
-========================
-
-* National Semiconductor LP5521 led driver chip
-* Datasheet: http://www.national.com/pf/LP/LP5521.html
-
-Authors: Mathias Nyman, Yuri Zaporozhets, Samu Onkalo
-Contact: Samu Onkalo (samu.p.onkalo-at-nokia.com)
-
-Description
------------
-
-LP5521 can drive up to 3 channels. Leds can be controlled directly via
-the led class control interface. Channels have generic names:
-lp5521:channelx, where x is 0 .. 2
-
-All three channels can be also controlled using the engine micro programs.
-More details of the instructions can be found from the public data sheet.
-
-LP5521 has the internal program memory for running various LED patterns.
-There are two ways to run LED patterns.
-
-1) Legacy interface - enginex_mode and enginex_load
- Control interface for the engines:
- x is 1 .. 3
- enginex_mode : disabled, load, run
- enginex_load : store program (visible only in engine load mode)
-
- Example (start to blink the channel 2 led):
- cd /sys/class/leds/lp5521:channel2/device
- echo "load" > engine3_mode
- echo "037f4d0003ff6000" > engine3_load
- echo "run" > engine3_mode
-
- To stop the engine:
- echo "disabled" > engine3_mode
-
-2) Firmware interface - LP55xx common interface
- For the details, please refer to 'firmware' section in leds-lp55xx.txt
-
-sysfs contains a selftest entry.
-The test communicates with the chip and checks that
-the clock mode is automatically set to the requested one.
-
-Each channel has its own led current settings.
-/sys/class/leds/lp5521:channel0/led_current - RW
-/sys/class/leds/lp5521:channel0/max_current - RO
-Format: 10x mA i.e 10 means 1.0 mA
-
-example platform data:
-
-Note: chan_nr can have values between 0 and 2.
-The name of each channel can be configurable.
-If the name field is not defined, the default name will be set to 'xxxx:channelN'
-(XXXX : pdata->label or i2c client name, N : channel number)
-
-static struct lp55xx_led_config lp5521_led_config[] = {
- {
- .name = "red",
- .chan_nr = 0,
- .led_current = 50,
- .max_current = 130,
- }, {
- .name = "green",
- .chan_nr = 1,
- .led_current = 0,
- .max_current = 130,
- }, {
- .name = "blue",
- .chan_nr = 2,
- .led_current = 0,
- .max_current = 130,
- }
-};
-
-static int lp5521_setup(void)
-{
- /* setup HW resources */
-}
-
-static void lp5521_release(void)
-{
- /* Release HW resources */
-}
-
-static void lp5521_enable(bool state)
-{
- /* Control of chip enable signal */
-}
-
-static struct lp55xx_platform_data lp5521_platform_data = {
- .led_config = lp5521_led_config,
- .num_channels = ARRAY_SIZE(lp5521_led_config),
- .clock_mode = LP55XX_CLOCK_EXT,
- .setup_resources = lp5521_setup,
- .release_resources = lp5521_release,
- .enable = lp5521_enable,
-};
-
-If the current is set to 0 in the platform data, that channel is
-disabled and it is not visible in the sysfs.
--- /dev/null
+========================
+Kernel driver for lp5523
+========================
+
+* National Semiconductor LP5523 led driver chip
+* Datasheet: http://www.national.com/pf/LP/LP5523.html
+
+Authors: Mathias Nyman, Yuri Zaporozhets, Samu Onkalo
+Contact: Samu Onkalo (samu.p.onkalo-at-nokia.com)
+
+Description
+-----------
+LP5523 can drive up to 9 channels. Leds can be controlled directly via
+the led class control interface.
+The name of each channel is configurable in the platform data - name and label.
+There are three options to make the channel name.
+
+a) Define the 'name' in the platform data
+
+To make specific channel name, then use 'name' platform data.
+
+- /sys/class/leds/R1 (name: 'R1')
+- /sys/class/leds/B1 (name: 'B1')
+
+b) Use the 'label' with no 'name' field
+
+For one device name with channel number, then use 'label'.
+- /sys/class/leds/RGB:channelN (label: 'RGB', N: 0 ~ 8)
+
+c) Default
+
+If both fields are NULL, 'lp5523' is used by default.
+- /sys/class/leds/lp5523:channelN (N: 0 ~ 8)
+
+LP5523 has the internal program memory for running various LED patterns.
+There are two ways to run LED patterns.
+
+1) Legacy interface - enginex_mode, enginex_load and enginex_leds
+
+ Control interface for the engines:
+
+ x is 1 .. 3
+
+ enginex_mode:
+ disabled, load, run
+ enginex_load:
+ microcode load
+ enginex_leds:
+ led mux control
+
+ ::
+
+ cd /sys/class/leds/lp5523:channel2/device
+ echo "load" > engine3_mode
+ echo "9d80400004ff05ff437f0000" > engine3_load
+ echo "111111111" > engine3_leds
+ echo "run" > engine3_mode
+
+ To stop the engine::
+
+ echo "disabled" > engine3_mode
+
+2) Firmware interface - LP55xx common interface
+
+For the details, please refer to 'firmware' section in leds-lp55xx.txt
+
+LP5523 has three master faders. If a channel is mapped to one of
+the master faders, its output is dimmed based on the value of the master
+fader.
+
+For example::
+
+ echo "123000123" > master_fader_leds
+
+creates the following channel-fader mappings::
+
+ channel 0,6 to master_fader1
+ channel 1,7 to master_fader2
+ channel 2,8 to master_fader3
+
+Then, to have 25% of the original output on channel 0,6::
+
+ echo 64 > master_fader1
+
+To have 0% of the original output (i.e. no output) channel 1,7::
+
+ echo 0 > master_fader2
+
+To have 100% of the original output (i.e. no dimming) on channel 2,8::
+
+ echo 255 > master_fader3
+
+To clear all master fader controls::
+
+ echo "000000000" > master_fader_leds
+
+Selftest uses always the current from the platform data.
+
+Each channel contains led current settings.
+- /sys/class/leds/lp5523:channel2/led_current - RW
+- /sys/class/leds/lp5523:channel2/max_current - RO
+
+Format: 10x mA i.e 10 means 1.0 mA
+
+Example platform data::
+
+ static struct lp55xx_led_config lp5523_led_config[] = {
+ {
+ .name = "D1",
+ .chan_nr = 0,
+ .led_current = 50,
+ .max_current = 130,
+ },
+ ...
+ {
+ .chan_nr = 8,
+ .led_current = 50,
+ .max_current = 130,
+ }
+ };
+
+ static int lp5523_setup(void)
+ {
+ /* Setup HW resources */
+ }
+
+ static void lp5523_release(void)
+ {
+ /* Release HW resources */
+ }
+
+ static void lp5523_enable(bool state)
+ {
+ /* Control chip enable signal */
+ }
+
+ static struct lp55xx_platform_data lp5523_platform_data = {
+ .led_config = lp5523_led_config,
+ .num_channels = ARRAY_SIZE(lp5523_led_config),
+ .clock_mode = LP55XX_CLOCK_EXT,
+ .setup_resources = lp5523_setup,
+ .release_resources = lp5523_release,
+ .enable = lp5523_enable,
+ };
+
+Note
+ chan_nr can have values between 0 and 8.
+++ /dev/null
-Kernel driver for lp5523
-========================
-
-* National Semiconductor LP5523 led driver chip
-* Datasheet: http://www.national.com/pf/LP/LP5523.html
-
-Authors: Mathias Nyman, Yuri Zaporozhets, Samu Onkalo
-Contact: Samu Onkalo (samu.p.onkalo-at-nokia.com)
-
-Description
------------
-LP5523 can drive up to 9 channels. Leds can be controlled directly via
-the led class control interface.
-The name of each channel is configurable in the platform data - name and label.
-There are three options to make the channel name.
-
-a) Define the 'name' in the platform data
-To make specific channel name, then use 'name' platform data.
-/sys/class/leds/R1 (name: 'R1')
-/sys/class/leds/B1 (name: 'B1')
-
-b) Use the 'label' with no 'name' field
-For one device name with channel number, then use 'label'.
-/sys/class/leds/RGB:channelN (label: 'RGB', N: 0 ~ 8)
-
-c) Default
-If both fields are NULL, 'lp5523' is used by default.
-/sys/class/leds/lp5523:channelN (N: 0 ~ 8)
-
-LP5523 has the internal program memory for running various LED patterns.
-There are two ways to run LED patterns.
-
-1) Legacy interface - enginex_mode, enginex_load and enginex_leds
- Control interface for the engines:
- x is 1 .. 3
- enginex_mode : disabled, load, run
- enginex_load : microcode load
- enginex_leds : led mux control
-
- cd /sys/class/leds/lp5523:channel2/device
- echo "load" > engine3_mode
- echo "9d80400004ff05ff437f0000" > engine3_load
- echo "111111111" > engine3_leds
- echo "run" > engine3_mode
-
- To stop the engine:
- echo "disabled" > engine3_mode
-
-2) Firmware interface - LP55xx common interface
- For the details, please refer to 'firmware' section in leds-lp55xx.txt
-
-LP5523 has three master faders. If a channel is mapped to one of
-the master faders, its output is dimmed based on the value of the master
-fader.
-
-For example,
-
- echo "123000123" > master_fader_leds
-
-creates the following channel-fader mappings:
-
- channel 0,6 to master_fader1
- channel 1,7 to master_fader2
- channel 2,8 to master_fader3
-
-Then, to have 25% of the original output on channel 0,6:
-
- echo 64 > master_fader1
-
-To have 0% of the original output (i.e. no output) channel 1,7:
-
- echo 0 > master_fader2
-
-To have 100% of the original output (i.e. no dimming) on channel 2,8:
-
- echo 255 > master_fader3
-
-To clear all master fader controls:
-
- echo "000000000" > master_fader_leds
-
-Selftest uses always the current from the platform data.
-
-Each channel contains led current settings.
-/sys/class/leds/lp5523:channel2/led_current - RW
-/sys/class/leds/lp5523:channel2/max_current - RO
-Format: 10x mA i.e 10 means 1.0 mA
-
-Example platform data:
-
-Note - chan_nr can have values between 0 and 8.
-
-static struct lp55xx_led_config lp5523_led_config[] = {
- {
- .name = "D1",
- .chan_nr = 0,
- .led_current = 50,
- .max_current = 130,
- },
-...
- {
- .chan_nr = 8,
- .led_current = 50,
- .max_current = 130,
- }
-};
-
-static int lp5523_setup(void)
-{
- /* Setup HW resources */
-}
-
-static void lp5523_release(void)
-{
- /* Release HW resources */
-}
-
-static void lp5523_enable(bool state)
-{
- /* Control chip enable signal */
-}
-
-static struct lp55xx_platform_data lp5523_platform_data = {
- .led_config = lp5523_led_config,
- .num_channels = ARRAY_SIZE(lp5523_led_config),
- .clock_mode = LP55XX_CLOCK_EXT,
- .setup_resources = lp5523_setup,
- .release_resources = lp5523_release,
- .enable = lp5523_enable,
-};
--- /dev/null
+========================
+Kernel driver for lp5562
+========================
+
+* TI LP5562 LED Driver
+
+Author: Milo(Woogyom) Kim <milo.kim@ti.com>
+
+Description
+===========
+
+ LP5562 can drive up to 4 channels. R/G/B and White.
+ LEDs can be controlled directly via the led class control interface.
+
+ All four channels can be also controlled using the engine micro programs.
+ LP5562 has the internal program memory for running various LED patterns.
+ For the details, please refer to 'firmware' section in leds-lp55xx.txt
+
+Device attribute
+================
+
+engine_mux
+ 3 Engines are allocated in LP5562, but the number of channel is 4.
+ Therefore each channel should be mapped to the engine number.
+
+ Value: RGB or W
+
+ This attribute is used for programming LED data with the firmware interface.
+ Unlike the LP5521/LP5523/55231, LP5562 has unique feature for the engine mux,
+ so additional sysfs is required
+
+ LED Map
+
+ ===== === ===============================
+ Red ... Engine 1 (fixed)
+ Green ... Engine 2 (fixed)
+ Blue ... Engine 3 (fixed)
+ White ... Engine 1 or 2 or 3 (selective)
+ ===== === ===============================
+
+How to load the program data using engine_mux
+=============================================
+
+ Before loading the LP5562 program data, engine_mux should be written between
+ the engine selection and loading the firmware.
+ Engine mux has two different mode, RGB and W.
+ RGB is used for loading RGB program data, W is used for W program data.
+
+ For example, run blinking green channel pattern::
+
+ echo 2 > /sys/bus/i2c/devices/xxxx/select_engine # 2 is for green channel
+ echo "RGB" > /sys/bus/i2c/devices/xxxx/engine_mux # engine mux for RGB
+ echo 1 > /sys/class/firmware/lp5562/loading
+ echo "4000600040FF6000" > /sys/class/firmware/lp5562/data
+ echo 0 > /sys/class/firmware/lp5562/loading
+ echo 1 > /sys/bus/i2c/devices/xxxx/run_engine
+
+ To run a blinking white pattern::
+
+ echo 1 or 2 or 3 > /sys/bus/i2c/devices/xxxx/select_engine
+ echo "W" > /sys/bus/i2c/devices/xxxx/engine_mux
+ echo 1 > /sys/class/firmware/lp5562/loading
+ echo "4000600040FF6000" > /sys/class/firmware/lp5562/data
+ echo 0 > /sys/class/firmware/lp5562/loading
+ echo 1 > /sys/bus/i2c/devices/xxxx/run_engine
+
+How to load the predefined patterns
+===================================
+
+ Please refer to 'leds-lp55xx.txt"
+
+Setting Current of Each Channel
+===============================
+
+ Like LP5521 and LP5523/55231, LP5562 provides LED current settings.
+ The 'led_current' and 'max_current' are used.
+
+Example of Platform data
+========================
+
+::
+
+ static struct lp55xx_led_config lp5562_led_config[] = {
+ {
+ .name = "R",
+ .chan_nr = 0,
+ .led_current = 20,
+ .max_current = 40,
+ },
+ {
+ .name = "G",
+ .chan_nr = 1,
+ .led_current = 20,
+ .max_current = 40,
+ },
+ {
+ .name = "B",
+ .chan_nr = 2,
+ .led_current = 20,
+ .max_current = 40,
+ },
+ {
+ .name = "W",
+ .chan_nr = 3,
+ .led_current = 20,
+ .max_current = 40,
+ },
+ };
+
+ static int lp5562_setup(void)
+ {
+ /* setup HW resources */
+ }
+
+ static void lp5562_release(void)
+ {
+ /* Release HW resources */
+ }
+
+ static void lp5562_enable(bool state)
+ {
+ /* Control of chip enable signal */
+ }
+
+ static struct lp55xx_platform_data lp5562_platform_data = {
+ .led_config = lp5562_led_config,
+ .num_channels = ARRAY_SIZE(lp5562_led_config),
+ .setup_resources = lp5562_setup,
+ .release_resources = lp5562_release,
+ .enable = lp5562_enable,
+ };
+
+To configure the platform specific data, lp55xx_platform_data structure is used
+
+
+If the current is set to 0 in the platform data, that channel is
+disabled and it is not visible in the sysfs.
+++ /dev/null
-Kernel driver for LP5562
-========================
-
-* TI LP5562 LED Driver
-
-Author: Milo(Woogyom) Kim <milo.kim@ti.com>
-
-Description
-
- LP5562 can drive up to 4 channels. R/G/B and White.
- LEDs can be controlled directly via the led class control interface.
-
- All four channels can be also controlled using the engine micro programs.
- LP5562 has the internal program memory for running various LED patterns.
- For the details, please refer to 'firmware' section in leds-lp55xx.txt
-
-Device attribute: engine_mux
-
- 3 Engines are allocated in LP5562, but the number of channel is 4.
- Therefore each channel should be mapped to the engine number.
- Value : RGB or W
-
- This attribute is used for programming LED data with the firmware interface.
- Unlike the LP5521/LP5523/55231, LP5562 has unique feature for the engine mux,
- so additional sysfs is required.
-
- LED Map
- Red ... Engine 1 (fixed)
- Green ... Engine 2 (fixed)
- Blue ... Engine 3 (fixed)
- White ... Engine 1 or 2 or 3 (selective)
-
-How to load the program data using engine_mux
-
- Before loading the LP5562 program data, engine_mux should be written between
- the engine selection and loading the firmware.
- Engine mux has two different mode, RGB and W.
- RGB is used for loading RGB program data, W is used for W program data.
-
- For example, run blinking green channel pattern,
- echo 2 > /sys/bus/i2c/devices/xxxx/select_engine # 2 is for green channel
- echo "RGB" > /sys/bus/i2c/devices/xxxx/engine_mux # engine mux for RGB
- echo 1 > /sys/class/firmware/lp5562/loading
- echo "4000600040FF6000" > /sys/class/firmware/lp5562/data
- echo 0 > /sys/class/firmware/lp5562/loading
- echo 1 > /sys/bus/i2c/devices/xxxx/run_engine
-
- To run a blinking white pattern,
- echo 1 or 2 or 3 > /sys/bus/i2c/devices/xxxx/select_engine
- echo "W" > /sys/bus/i2c/devices/xxxx/engine_mux
- echo 1 > /sys/class/firmware/lp5562/loading
- echo "4000600040FF6000" > /sys/class/firmware/lp5562/data
- echo 0 > /sys/class/firmware/lp5562/loading
- echo 1 > /sys/bus/i2c/devices/xxxx/run_engine
-
-How to load the predefined patterns
-
- Please refer to 'leds-lp55xx.txt"
-
-Setting Current of Each Channel
-
- Like LP5521 and LP5523/55231, LP5562 provides LED current settings.
- The 'led_current' and 'max_current' are used.
-
-(Example of Platform data)
-
-To configure the platform specific data, lp55xx_platform_data structure is used.
-
-static struct lp55xx_led_config lp5562_led_config[] = {
- {
- .name = "R",
- .chan_nr = 0,
- .led_current = 20,
- .max_current = 40,
- },
- {
- .name = "G",
- .chan_nr = 1,
- .led_current = 20,
- .max_current = 40,
- },
- {
- .name = "B",
- .chan_nr = 2,
- .led_current = 20,
- .max_current = 40,
- },
- {
- .name = "W",
- .chan_nr = 3,
- .led_current = 20,
- .max_current = 40,
- },
-};
-
-static int lp5562_setup(void)
-{
- /* setup HW resources */
-}
-
-static void lp5562_release(void)
-{
- /* Release HW resources */
-}
-
-static void lp5562_enable(bool state)
-{
- /* Control of chip enable signal */
-}
-
-static struct lp55xx_platform_data lp5562_platform_data = {
- .led_config = lp5562_led_config,
- .num_channels = ARRAY_SIZE(lp5562_led_config),
- .setup_resources = lp5562_setup,
- .release_resources = lp5562_release,
- .enable = lp5562_enable,
-};
-
-If the current is set to 0 in the platform data, that channel is
-disabled and it is not visible in the sysfs.
--- /dev/null
+=================================================
+LP5521/LP5523/LP55231/LP5562/LP8501 Common Driver
+=================================================
+
+Authors: Milo(Woogyom) Kim <milo.kim@ti.com>
+
+Description
+-----------
+LP5521, LP5523/55231, LP5562 and LP8501 have common features as below.
+
+ Register access via the I2C
+ Device initialization/deinitialization
+ Create LED class devices for multiple output channels
+ Device attributes for user-space interface
+ Program memory for running LED patterns
+
+The LP55xx common driver provides these features using exported functions.
+
+ lp55xx_init_device() / lp55xx_deinit_device()
+ lp55xx_register_leds() / lp55xx_unregister_leds()
+ lp55xx_regsister_sysfs() / lp55xx_unregister_sysfs()
+
+( Driver Structure Data )
+
+In lp55xx common driver, two different data structure is used.
+
+* lp55xx_led
+ control multi output LED channels such as led current, channel index.
+* lp55xx_chip
+ general chip control such like the I2C and platform data.
+
+For example, LP5521 has maximum 3 LED channels.
+LP5523/55231 has 9 output channels::
+
+ lp55xx_chip for LP5521 ... lp55xx_led #1
+ lp55xx_led #2
+ lp55xx_led #3
+
+ lp55xx_chip for LP5523 ... lp55xx_led #1
+ lp55xx_led #2
+ .
+ .
+ lp55xx_led #9
+
+( Chip Dependent Code )
+
+To support device specific configurations, special structure
+'lpxx_device_config' is used.
+
+ - Maximum number of channels
+ - Reset command, chip enable command
+ - Chip specific initialization
+ - Brightness control register access
+ - Setting LED output current
+ - Program memory address access for running patterns
+ - Additional device specific attributes
+
+( Firmware Interface )
+
+LP55xx family devices have the internal program memory for running
+various LED patterns.
+
+This pattern data is saved as a file in the user-land or
+hex byte string is written into the memory through the I2C.
+
+LP55xx common driver supports the firmware interface.
+
+LP55xx chips have three program engines.
+
+To load and run the pattern, the programming sequence is following.
+
+ (1) Select an engine number (1/2/3)
+ (2) Mode change to load
+ (3) Write pattern data into selected area
+ (4) Mode change to run
+
+The LP55xx common driver provides simple interfaces as below.
+
+select_engine:
+ Select which engine is used for running program
+run_engine:
+ Start program which is loaded via the firmware interface
+firmware:
+ Load program data
+
+In case of LP5523, one more command is required, 'enginex_leds'.
+It is used for selecting LED output(s) at each engine number.
+In more details, please refer to 'leds-lp5523.txt'.
+
+For example, run blinking pattern in engine #1 of LP5521::
+
+ echo 1 > /sys/bus/i2c/devices/xxxx/select_engine
+ echo 1 > /sys/class/firmware/lp5521/loading
+ echo "4000600040FF6000" > /sys/class/firmware/lp5521/data
+ echo 0 > /sys/class/firmware/lp5521/loading
+ echo 1 > /sys/bus/i2c/devices/xxxx/run_engine
+
+For example, run blinking pattern in engine #3 of LP55231
+
+Two LEDs are configured as pattern output channels::
+
+ echo 3 > /sys/bus/i2c/devices/xxxx/select_engine
+ echo 1 > /sys/class/firmware/lp55231/loading
+ echo "9d0740ff7e0040007e00a0010000" > /sys/class/firmware/lp55231/data
+ echo 0 > /sys/class/firmware/lp55231/loading
+ echo "000001100" > /sys/bus/i2c/devices/xxxx/engine3_leds
+ echo 1 > /sys/bus/i2c/devices/xxxx/run_engine
+
+To start blinking patterns in engine #2 and #3 simultaneously::
+
+ for idx in 2 3
+ do
+ echo $idx > /sys/class/leds/red/device/select_engine
+ sleep 0.1
+ echo 1 > /sys/class/firmware/lp5521/loading
+ echo "4000600040FF6000" > /sys/class/firmware/lp5521/data
+ echo 0 > /sys/class/firmware/lp5521/loading
+ done
+ echo 1 > /sys/class/leds/red/device/run_engine
+
+Here is another example for LP5523.
+
+Full LED strings are selected by 'engine2_leds'::
+
+ echo 2 > /sys/bus/i2c/devices/xxxx/select_engine
+ echo 1 > /sys/class/firmware/lp5523/loading
+ echo "9d80400004ff05ff437f0000" > /sys/class/firmware/lp5523/data
+ echo 0 > /sys/class/firmware/lp5523/loading
+ echo "111111111" > /sys/bus/i2c/devices/xxxx/engine2_leds
+ echo 1 > /sys/bus/i2c/devices/xxxx/run_engine
+
+As soon as 'loading' is set to 0, registered callback is called.
+Inside the callback, the selected engine is loaded and memory is updated.
+To run programmed pattern, 'run_engine' attribute should be enabled.
+
+The pattern sequence of LP8501 is similar to LP5523.
+
+However pattern data is specific.
+
+Ex 1) Engine 1 is used::
+
+ echo 1 > /sys/bus/i2c/devices/xxxx/select_engine
+ echo 1 > /sys/class/firmware/lp8501/loading
+ echo "9d0140ff7e0040007e00a001c000" > /sys/class/firmware/lp8501/data
+ echo 0 > /sys/class/firmware/lp8501/loading
+ echo 1 > /sys/bus/i2c/devices/xxxx/run_engine
+
+Ex 2) Engine 2 and 3 are used at the same time::
+
+ echo 2 > /sys/bus/i2c/devices/xxxx/select_engine
+ sleep 1
+ echo 1 > /sys/class/firmware/lp8501/loading
+ echo "9d0140ff7e0040007e00a001c000" > /sys/class/firmware/lp8501/data
+ echo 0 > /sys/class/firmware/lp8501/loading
+ sleep 1
+ echo 3 > /sys/bus/i2c/devices/xxxx/select_engine
+ sleep 1
+ echo 1 > /sys/class/firmware/lp8501/loading
+ echo "9d0340ff7e0040007e00a001c000" > /sys/class/firmware/lp8501/data
+ echo 0 > /sys/class/firmware/lp8501/loading
+ sleep 1
+ echo 1 > /sys/class/leds/d1/device/run_engine
+
+( 'run_engine' and 'firmware_cb' )
+
+The sequence of running the program data is common.
+
+But each device has own specific register addresses for commands.
+
+To support this, 'run_engine' and 'firmware_cb' are configurable in each driver.
+
+run_engine:
+ Control the selected engine
+firmware_cb:
+ The callback function after loading the firmware is done.
+
+ Chip specific commands for loading and updating program memory.
+
+( Predefined pattern data )
+
+Without the firmware interface, LP55xx driver provides another method for
+loading a LED pattern. That is 'predefined' pattern.
+
+A predefined pattern is defined in the platform data and load it(or them)
+via the sysfs if needed.
+
+To use the predefined pattern concept, 'patterns' and 'num_patterns' should be
+configured.
+
+Example of predefined pattern data::
+
+ /* mode_1: blinking data */
+ static const u8 mode_1[] = {
+ 0x40, 0x00, 0x60, 0x00, 0x40, 0xFF, 0x60, 0x00,
+ };
+
+ /* mode_2: always on */
+ static const u8 mode_2[] = { 0x40, 0xFF, };
+
+ struct lp55xx_predef_pattern board_led_patterns[] = {
+ {
+ .r = mode_1,
+ .size_r = ARRAY_SIZE(mode_1),
+ },
+ {
+ .b = mode_2,
+ .size_b = ARRAY_SIZE(mode_2),
+ },
+ }
+
+ struct lp55xx_platform_data lp5562_pdata = {
+ ...
+ .patterns = board_led_patterns,
+ .num_patterns = ARRAY_SIZE(board_led_patterns),
+ };
+
+Then, mode_1 and mode_2 can be run via through the sysfs::
+
+ echo 1 > /sys/bus/i2c/devices/xxxx/led_pattern # red blinking LED pattern
+ echo 2 > /sys/bus/i2c/devices/xxxx/led_pattern # blue LED always on
+
+To stop running pattern::
+
+ echo 0 > /sys/bus/i2c/devices/xxxx/led_pattern
+++ /dev/null
-LP5521/LP5523/LP55231/LP5562/LP8501 Common Driver
-=================================================
-
-Authors: Milo(Woogyom) Kim <milo.kim@ti.com>
-
-Description
------------
-LP5521, LP5523/55231, LP5562 and LP8501 have common features as below.
-
- Register access via the I2C
- Device initialization/deinitialization
- Create LED class devices for multiple output channels
- Device attributes for user-space interface
- Program memory for running LED patterns
-
-The LP55xx common driver provides these features using exported functions.
- lp55xx_init_device() / lp55xx_deinit_device()
- lp55xx_register_leds() / lp55xx_unregister_leds()
- lp55xx_regsister_sysfs() / lp55xx_unregister_sysfs()
-
-( Driver Structure Data )
-
-In lp55xx common driver, two different data structure is used.
-
-o lp55xx_led
- control multi output LED channels such as led current, channel index.
-o lp55xx_chip
- general chip control such like the I2C and platform data.
-
-For example, LP5521 has maximum 3 LED channels.
-LP5523/55231 has 9 output channels.
-
-lp55xx_chip for LP5521 ... lp55xx_led #1
- lp55xx_led #2
- lp55xx_led #3
-
-lp55xx_chip for LP5523 ... lp55xx_led #1
- lp55xx_led #2
- .
- .
- lp55xx_led #9
-
-( Chip Dependent Code )
-
-To support device specific configurations, special structure
-'lpxx_device_config' is used.
-
- Maximum number of channels
- Reset command, chip enable command
- Chip specific initialization
- Brightness control register access
- Setting LED output current
- Program memory address access for running patterns
- Additional device specific attributes
-
-( Firmware Interface )
-
-LP55xx family devices have the internal program memory for running
-various LED patterns.
-This pattern data is saved as a file in the user-land or
-hex byte string is written into the memory through the I2C.
-LP55xx common driver supports the firmware interface.
-
-LP55xx chips have three program engines.
-To load and run the pattern, the programming sequence is following.
- (1) Select an engine number (1/2/3)
- (2) Mode change to load
- (3) Write pattern data into selected area
- (4) Mode change to run
-
-The LP55xx common driver provides simple interfaces as below.
-select_engine : Select which engine is used for running program
-run_engine : Start program which is loaded via the firmware interface
-firmware : Load program data
-
-In case of LP5523, one more command is required, 'enginex_leds'.
-It is used for selecting LED output(s) at each engine number.
-In more details, please refer to 'leds-lp5523.txt'.
-
-For example, run blinking pattern in engine #1 of LP5521
-echo 1 > /sys/bus/i2c/devices/xxxx/select_engine
-echo 1 > /sys/class/firmware/lp5521/loading
-echo "4000600040FF6000" > /sys/class/firmware/lp5521/data
-echo 0 > /sys/class/firmware/lp5521/loading
-echo 1 > /sys/bus/i2c/devices/xxxx/run_engine
-
-For example, run blinking pattern in engine #3 of LP55231
-Two LEDs are configured as pattern output channels.
-echo 3 > /sys/bus/i2c/devices/xxxx/select_engine
-echo 1 > /sys/class/firmware/lp55231/loading
-echo "9d0740ff7e0040007e00a0010000" > /sys/class/firmware/lp55231/data
-echo 0 > /sys/class/firmware/lp55231/loading
-echo "000001100" > /sys/bus/i2c/devices/xxxx/engine3_leds
-echo 1 > /sys/bus/i2c/devices/xxxx/run_engine
-
-To start blinking patterns in engine #2 and #3 simultaneously,
-for idx in 2 3
-do
- echo $idx > /sys/class/leds/red/device/select_engine
- sleep 0.1
- echo 1 > /sys/class/firmware/lp5521/loading
- echo "4000600040FF6000" > /sys/class/firmware/lp5521/data
- echo 0 > /sys/class/firmware/lp5521/loading
-done
-echo 1 > /sys/class/leds/red/device/run_engine
-
-Here is another example for LP5523.
-Full LED strings are selected by 'engine2_leds'.
-echo 2 > /sys/bus/i2c/devices/xxxx/select_engine
-echo 1 > /sys/class/firmware/lp5523/loading
-echo "9d80400004ff05ff437f0000" > /sys/class/firmware/lp5523/data
-echo 0 > /sys/class/firmware/lp5523/loading
-echo "111111111" > /sys/bus/i2c/devices/xxxx/engine2_leds
-echo 1 > /sys/bus/i2c/devices/xxxx/run_engine
-
-As soon as 'loading' is set to 0, registered callback is called.
-Inside the callback, the selected engine is loaded and memory is updated.
-To run programmed pattern, 'run_engine' attribute should be enabled.
-
-The pattern sequence of LP8501 is similar to LP5523.
-However pattern data is specific.
-Ex 1) Engine 1 is used
-echo 1 > /sys/bus/i2c/devices/xxxx/select_engine
-echo 1 > /sys/class/firmware/lp8501/loading
-echo "9d0140ff7e0040007e00a001c000" > /sys/class/firmware/lp8501/data
-echo 0 > /sys/class/firmware/lp8501/loading
-echo 1 > /sys/bus/i2c/devices/xxxx/run_engine
-
-Ex 2) Engine 2 and 3 are used at the same time
-echo 2 > /sys/bus/i2c/devices/xxxx/select_engine
-sleep 1
-echo 1 > /sys/class/firmware/lp8501/loading
-echo "9d0140ff7e0040007e00a001c000" > /sys/class/firmware/lp8501/data
-echo 0 > /sys/class/firmware/lp8501/loading
-sleep 1
-echo 3 > /sys/bus/i2c/devices/xxxx/select_engine
-sleep 1
-echo 1 > /sys/class/firmware/lp8501/loading
-echo "9d0340ff7e0040007e00a001c000" > /sys/class/firmware/lp8501/data
-echo 0 > /sys/class/firmware/lp8501/loading
-sleep 1
-echo 1 > /sys/class/leds/d1/device/run_engine
-
-( 'run_engine' and 'firmware_cb' )
-The sequence of running the program data is common.
-But each device has own specific register addresses for commands.
-To support this, 'run_engine' and 'firmware_cb' are configurable in each driver.
-run_engine : Control the selected engine
-firmware_cb : The callback function after loading the firmware is done.
- Chip specific commands for loading and updating program memory.
-
-( Predefined pattern data )
-
-Without the firmware interface, LP55xx driver provides another method for
-loading a LED pattern. That is 'predefined' pattern.
-A predefined pattern is defined in the platform data and load it(or them)
-via the sysfs if needed.
-To use the predefined pattern concept, 'patterns' and 'num_patterns' should be
-configured.
-
- Example of predefined pattern data:
-
- /* mode_1: blinking data */
- static const u8 mode_1[] = {
- 0x40, 0x00, 0x60, 0x00, 0x40, 0xFF, 0x60, 0x00,
- };
-
- /* mode_2: always on */
- static const u8 mode_2[] = { 0x40, 0xFF, };
-
- struct lp55xx_predef_pattern board_led_patterns[] = {
- {
- .r = mode_1,
- .size_r = ARRAY_SIZE(mode_1),
- },
- {
- .b = mode_2,
- .size_b = ARRAY_SIZE(mode_2),
- },
- }
-
- struct lp55xx_platform_data lp5562_pdata = {
- ...
- .patterns = board_led_patterns,
- .num_patterns = ARRAY_SIZE(board_led_patterns),
- };
-
-Then, mode_1 and mode_2 can be run via through the sysfs.
-
- echo 1 > /sys/bus/i2c/devices/xxxx/led_pattern # red blinking LED pattern
- echo 2 > /sys/bus/i2c/devices/xxxx/led_pattern # blue LED always on
-
-To stop running pattern,
- echo 0 > /sys/bus/i2c/devices/xxxx/led_pattern
--- /dev/null
+=======================================
+Kernel driver for Mellanox systems LEDs
+=======================================
+
+Provide system LED support for the nex Mellanox systems:
+"msx6710", "msx6720", "msb7700", "msn2700", "msx1410",
+"msn2410", "msb7800", "msn2740", "msn2100".
+
+Description
+-----------
+Driver provides the following LEDs for the systems "msx6710", "msx6720",
+"msb7700", "msn2700", "msx1410", "msn2410", "msb7800", "msn2740":
+
+ - mlxcpld:fan1:green
+ - mlxcpld:fan1:red
+ - mlxcpld:fan2:green
+ - mlxcpld:fan2:red
+ - mlxcpld:fan3:green
+ - mlxcpld:fan3:red
+ - mlxcpld:fan4:green
+ - mlxcpld:fan4:red
+ - mlxcpld:psu:green
+ - mlxcpld:psu:red
+ - mlxcpld:status:green
+ - mlxcpld:status:red
+
+ "status"
+ - CPLD reg offset: 0x20
+ - Bits [3:0]
+
+ "psu"
+ - CPLD reg offset: 0x20
+ - Bits [7:4]
+
+ "fan1"
+ - CPLD reg offset: 0x21
+ - Bits [3:0]
+
+ "fan2"
+ - CPLD reg offset: 0x21
+ - Bits [7:4]
+
+ "fan3"
+ - CPLD reg offset: 0x22
+ - Bits [3:0]
+
+ "fan4"
+ - CPLD reg offset: 0x22
+ - Bits [7:4]
+
+ Color mask for all the above LEDs:
+
+ [bit3,bit2,bit1,bit0] or
+ [bit7,bit6,bit5,bit4]:
+
+ - [0,0,0,0] = LED OFF
+ - [0,1,0,1] = Red static ON
+ - [1,1,0,1] = Green static ON
+ - [0,1,1,0] = Red blink 3Hz
+ - [1,1,1,0] = Green blink 3Hz
+ - [0,1,1,1] = Red blink 6Hz
+ - [1,1,1,1] = Green blink 6Hz
+
+Driver provides the following LEDs for the system "msn2100":
+
+ - mlxcpld:fan:green
+ - mlxcpld:fan:red
+ - mlxcpld:psu1:green
+ - mlxcpld:psu1:red
+ - mlxcpld:psu2:green
+ - mlxcpld:psu2:red
+ - mlxcpld:status:green
+ - mlxcpld:status:red
+ - mlxcpld:uid:blue
+
+ "status"
+ - CPLD reg offset: 0x20
+ - Bits [3:0]
+
+ "fan"
+ - CPLD reg offset: 0x21
+ - Bits [3:0]
+
+ "psu1"
+ - CPLD reg offset: 0x23
+ - Bits [3:0]
+
+ "psu2"
+ - CPLD reg offset: 0x23
+ - Bits [7:4]
+
+ "uid"
+ - CPLD reg offset: 0x24
+ - Bits [3:0]
+
+ Color mask for all the above LEDs, excepted uid:
+
+ [bit3,bit2,bit1,bit0] or
+ [bit7,bit6,bit5,bit4]:
+
+ - [0,0,0,0] = LED OFF
+ - [0,1,0,1] = Red static ON
+ - [1,1,0,1] = Green static ON
+ - [0,1,1,0] = Red blink 3Hz
+ - [1,1,1,0] = Green blink 3Hz
+ - [0,1,1,1] = Red blink 6Hz
+ - [1,1,1,1] = Green blink 6Hz
+
+ Color mask for uid LED:
+ [bit3,bit2,bit1,bit0]:
+
+ - [0,0,0,0] = LED OFF
+ - [1,1,0,1] = Blue static ON
+ - [1,1,1,0] = Blue blink 3Hz
+ - [1,1,1,1] = Blue blink 6Hz
+
+Driver supports HW blinking at 3Hz and 6Hz frequency (50% duty cycle).
+For 3Hz duty cylce is about 167 msec, for 6Hz is about 83 msec.
+++ /dev/null
-Kernel driver for Mellanox systems LEDs
-=======================================
-
-Provide system LED support for the nex Mellanox systems:
-"msx6710", "msx6720", "msb7700", "msn2700", "msx1410",
-"msn2410", "msb7800", "msn2740", "msn2100".
-
-Description
------------
-Driver provides the following LEDs for the systems "msx6710", "msx6720",
-"msb7700", "msn2700", "msx1410", "msn2410", "msb7800", "msn2740":
- mlxcpld:fan1:green
- mlxcpld:fan1:red
- mlxcpld:fan2:green
- mlxcpld:fan2:red
- mlxcpld:fan3:green
- mlxcpld:fan3:red
- mlxcpld:fan4:green
- mlxcpld:fan4:red
- mlxcpld:psu:green
- mlxcpld:psu:red
- mlxcpld:status:green
- mlxcpld:status:red
-
- "status"
- CPLD reg offset: 0x20
- Bits [3:0]
-
- "psu"
- CPLD reg offset: 0x20
- Bits [7:4]
-
- "fan1"
- CPLD reg offset: 0x21
- Bits [3:0]
-
- "fan2"
- CPLD reg offset: 0x21
- Bits [7:4]
-
- "fan3"
- CPLD reg offset: 0x22
- Bits [3:0]
-
- "fan4"
- CPLD reg offset: 0x22
- Bits [7:4]
-
- Color mask for all the above LEDs:
- [bit3,bit2,bit1,bit0] or
- [bit7,bit6,bit5,bit4]:
- [0,0,0,0] = LED OFF
- [0,1,0,1] = Red static ON
- [1,1,0,1] = Green static ON
- [0,1,1,0] = Red blink 3Hz
- [1,1,1,0] = Green blink 3Hz
- [0,1,1,1] = Red blink 6Hz
- [1,1,1,1] = Green blink 6Hz
-
-Driver provides the following LEDs for the system "msn2100":
- mlxcpld:fan:green
- mlxcpld:fan:red
- mlxcpld:psu1:green
- mlxcpld:psu1:red
- mlxcpld:psu2:green
- mlxcpld:psu2:red
- mlxcpld:status:green
- mlxcpld:status:red
- mlxcpld:uid:blue
-
- "status"
- CPLD reg offset: 0x20
- Bits [3:0]
-
- "fan"
- CPLD reg offset: 0x21
- Bits [3:0]
-
- "psu1"
- CPLD reg offset: 0x23
- Bits [3:0]
-
- "psu2"
- CPLD reg offset: 0x23
- Bits [7:4]
-
- "uid"
- CPLD reg offset: 0x24
- Bits [3:0]
-
- Color mask for all the above LEDs, excepted uid:
- [bit3,bit2,bit1,bit0] or
- [bit7,bit6,bit5,bit4]:
- [0,0,0,0] = LED OFF
- [0,1,0,1] = Red static ON
- [1,1,0,1] = Green static ON
- [0,1,1,0] = Red blink 3Hz
- [1,1,1,0] = Green blink 3Hz
- [0,1,1,1] = Red blink 6Hz
- [1,1,1,1] = Green blink 6Hz
-
- Color mask for uid LED:
- [bit3,bit2,bit1,bit0]:
- [0,0,0,0] = LED OFF
- [1,1,0,1] = Blue static ON
- [1,1,1,0] = Blue blink 3Hz
- [1,1,1,1] = Blue blink 6Hz
-
-Driver supports HW blinking at 3Hz and 6Hz frequency (50% duty cycle).
-For 3Hz duty cylce is about 167 msec, for 6Hz is about 83 msec.
--- /dev/null
+====================
+One-shot LED Trigger
+====================
+
+This is a LED trigger useful for signaling the user of an event where there are
+no clear trap points to put standard led-on and led-off settings. Using this
+trigger, the application needs only to signal the trigger when an event has
+happened, than the trigger turns the LED on and than keeps it off for a
+specified amount of time.
+
+This trigger is meant to be usable both for sporadic and dense events. In the
+first case, the trigger produces a clear single controlled blink for each
+event, while in the latter it keeps blinking at constant rate, as to signal
+that the events are arriving continuously.
+
+A one-shot LED only stays in a constant state when there are no events. An
+additional "invert" property specifies if the LED has to stay off (normal) or
+on (inverted) when not rearmed.
+
+The trigger can be activated from user space on led class devices as shown
+below::
+
+ echo oneshot > trigger
+
+This adds sysfs attributes to the LED that are documented in:
+Documentation/ABI/testing/sysfs-class-led-trigger-oneshot
+
+Example use-case: network devices, initialization::
+
+ echo oneshot > trigger # set trigger for this led
+ echo 33 > delay_on # blink at 1 / (33 + 33) Hz on continuous traffic
+ echo 33 > delay_off
+
+interface goes up::
+
+ echo 1 > invert # set led as normally-on, turn the led on
+
+packet received/transmitted::
+
+ echo 1 > shot # led starts blinking, ignored if already blinking
+
+interface goes down::
+
+ echo 0 > invert # set led as normally-off, turn the led off
+++ /dev/null
-One-shot LED Trigger
-====================
-
-This is a LED trigger useful for signaling the user of an event where there are
-no clear trap points to put standard led-on and led-off settings. Using this
-trigger, the application needs only to signal the trigger when an event has
-happened, than the trigger turns the LED on and than keeps it off for a
-specified amount of time.
-
-This trigger is meant to be usable both for sporadic and dense events. In the
-first case, the trigger produces a clear single controlled blink for each
-event, while in the latter it keeps blinking at constant rate, as to signal
-that the events are arriving continuously.
-
-A one-shot LED only stays in a constant state when there are no events. An
-additional "invert" property specifies if the LED has to stay off (normal) or
-on (inverted) when not rearmed.
-
-The trigger can be activated from user space on led class devices as shown
-below:
-
- echo oneshot > trigger
-
-This adds sysfs attributes to the LED that are documented in:
-Documentation/ABI/testing/sysfs-class-led-trigger-oneshot
-
-Example use-case: network devices, initialization:
-
- echo oneshot > trigger # set trigger for this led
- echo 33 > delay_on # blink at 1 / (33 + 33) Hz on continuous traffic
- echo 33 > delay_off
-
-interface goes up:
-
- echo 1 > invert # set led as normally-on, turn the led on
-
-packet received/transmitted:
-
- echo 1 > shot # led starts blinking, ignored if already blinking
-
-interface goes down
-
- echo 0 > invert # set led as normally-off, turn the led off
--- /dev/null
+=====================
+LED Transient Trigger
+=====================
+
+The leds timer trigger does not currently have an interface to activate
+a one shot timer. The current support allows for setting two timers, one for
+specifying how long a state to be on, and the second for how long the state
+to be off. The delay_on value specifies the time period an LED should stay
+in on state, followed by a delay_off value that specifies how long the LED
+should stay in off state. The on and off cycle repeats until the trigger
+gets deactivated. There is no provision for one time activation to implement
+features that require an on or off state to be held just once and then stay in
+the original state forever.
+
+Without one shot timer interface, user space can still use timer trigger to
+set a timer to hold a state, however when user space application crashes or
+goes away without deactivating the timer, the hardware will be left in that
+state permanently.
+
+As a specific example of this use-case, let's look at vibrate feature on
+phones. Vibrate function on phones is implemented using PWM pins on SoC or
+PMIC. There is a need to activate one shot timer to control the vibrate
+feature, to prevent user space crashes leaving the phone in vibrate mode
+permanently causing the battery to drain.
+
+Transient trigger addresses the need for one shot timer activation. The
+transient trigger can be enabled and disabled just like the other leds
+triggers.
+
+When an led class device driver registers itself, it can specify all leds
+triggers it supports and a default trigger. During registration, activation
+routine for the default trigger gets called. During registration of an led
+class device, the LED state does not change.
+
+When the driver unregisters, deactivation routine for the currently active
+trigger will be called, and LED state is changed to LED_OFF.
+
+Driver suspend changes the LED state to LED_OFF and resume doesn't change
+the state. Please note that there is no explicit interaction between the
+suspend and resume actions and the currently enabled trigger. LED state
+changes are suspended while the driver is in suspend state. Any timers
+that are active at the time driver gets suspended, continue to run, without
+being able to actually change the LED state. Once driver is resumed, triggers
+start functioning again.
+
+LED state changes are controlled using brightness which is a common led
+class device property. When brightness is set to 0 from user space via
+echo 0 > brightness, it will result in deactivating the current trigger.
+
+Transient trigger uses standard register and unregister interfaces. During
+trigger registration, for each led class device that specifies this trigger
+as its default trigger, trigger activation routine will get called. During
+registration, the LED state does not change, unless there is another trigger
+active, in which case LED state changes to LED_OFF.
+
+During trigger unregistration, LED state gets changed to LED_OFF.
+
+Transient trigger activation routine doesn't change the LED state. It
+creates its properties and does its initialization. Transient trigger
+deactivation routine, will cancel any timer that is active before it cleans
+up and removes the properties it created. It will restore the LED state to
+non-transient state. When driver gets suspended, irrespective of the transient
+state, the LED state changes to LED_OFF.
+
+Transient trigger can be enabled and disabled from user space on led class
+devices, that support this trigger as shown below::
+
+ echo transient > trigger
+ echo none > trigger
+
+NOTE:
+ Add a new property trigger state to control the state.
+
+This trigger exports three properties, activate, state, and duration. When
+transient trigger is activated these properties are set to default values.
+
+- duration allows setting timer value in msecs. The initial value is 0.
+- activate allows activating and deactivating the timer specified by
+ duration as needed. The initial and default value is 0. This will allow
+ duration to be set after trigger activation.
+- state allows user to specify a transient state to be held for the specified
+ duration.
+
+ activate
+ - one shot timer activate mechanism.
+ 1 when activated, 0 when deactivated.
+ default value is zero when transient trigger is enabled,
+ to allow duration to be set.
+
+ activate state indicates a timer with a value of specified
+ duration running.
+ deactivated state indicates that there is no active timer
+ running.
+
+ duration
+ - one shot timer value. When activate is set, duration value
+ is used to start a timer that runs once. This value doesn't
+ get changed by the trigger unless user does a set via
+ echo new_value > duration
+
+ state
+ - transient state to be held. It has two values 0 or 1. 0 maps
+ to LED_OFF and 1 maps to LED_FULL. The specified state is
+ held for the duration of the one shot timer and then the
+ state gets changed to the non-transient state which is the
+ inverse of transient state.
+ If state = LED_FULL, when the timer runs out the state will
+ go back to LED_OFF.
+ If state = LED_OFF, when the timer runs out the state will
+ go back to LED_FULL.
+ Please note that current LED state is not checked prior to
+ changing the state to the specified state.
+ Driver could map these values to inverted depending on the
+ default states it defines for the LED in its brightness_set()
+ interface which is called from the led brightness_set()
+ interfaces to control the LED state.
+
+When timer expires activate goes back to deactivated state, duration is left
+at the set value to be used when activate is set at a future time. This will
+allow user app to set the time once and activate it to run it once for the
+specified value as needed. When timer expires, state is restored to the
+non-transient state which is the inverse of the transient state:
+
+ ================= ===============================================
+ echo 1 > activate starts timer = duration when duration is not 0.
+ echo 0 > activate cancels currently running timer.
+ echo n > duration stores timer value to be used upon next
+ activate. Currently active timer if
+ any, continues to run for the specified time.
+ echo 0 > duration stores timer value to be used upon next
+ activate. Currently active timer if any,
+ continues to run for the specified time.
+ echo 1 > state stores desired transient state LED_FULL to be
+ held for the specified duration.
+ echo 0 > state stores desired transient state LED_OFF to be
+ held for the specified duration.
+ ================= ===============================================
+
+What is not supported
+=====================
+
+- Timer activation is one shot and extending and/or shortening the timer
+ is not supported.
+
+Examples
+========
+
+use-case 1::
+
+ echo transient > trigger
+ echo n > duration
+ echo 1 > state
+
+repeat the following step as needed::
+
+ echo 1 > activate - start timer = duration to run once
+ echo 1 > activate - start timer = duration to run once
+ echo none > trigger
+
+This trigger is intended to be used for for the following example use cases:
+
+ - Control of vibrate (phones, tablets etc.) hardware by user space app.
+ - Use of LED by user space app as activity indicator.
+ - Use of LED by user space app as a kind of watchdog indicator -- as
+ long as the app is alive, it can keep the LED illuminated, if it dies
+ the LED will be extinguished automatically.
+ - Use by any user space app that needs a transient GPIO output.
+++ /dev/null
-LED Transient Trigger
-=====================
-
-The leds timer trigger does not currently have an interface to activate
-a one shot timer. The current support allows for setting two timers, one for
-specifying how long a state to be on, and the second for how long the state
-to be off. The delay_on value specifies the time period an LED should stay
-in on state, followed by a delay_off value that specifies how long the LED
-should stay in off state. The on and off cycle repeats until the trigger
-gets deactivated. There is no provision for one time activation to implement
-features that require an on or off state to be held just once and then stay in
-the original state forever.
-
-Without one shot timer interface, user space can still use timer trigger to
-set a timer to hold a state, however when user space application crashes or
-goes away without deactivating the timer, the hardware will be left in that
-state permanently.
-
-As a specific example of this use-case, let's look at vibrate feature on
-phones. Vibrate function on phones is implemented using PWM pins on SoC or
-PMIC. There is a need to activate one shot timer to control the vibrate
-feature, to prevent user space crashes leaving the phone in vibrate mode
-permanently causing the battery to drain.
-
-Transient trigger addresses the need for one shot timer activation. The
-transient trigger can be enabled and disabled just like the other leds
-triggers.
-
-When an led class device driver registers itself, it can specify all leds
-triggers it supports and a default trigger. During registration, activation
-routine for the default trigger gets called. During registration of an led
-class device, the LED state does not change.
-
-When the driver unregisters, deactivation routine for the currently active
-trigger will be called, and LED state is changed to LED_OFF.
-
-Driver suspend changes the LED state to LED_OFF and resume doesn't change
-the state. Please note that there is no explicit interaction between the
-suspend and resume actions and the currently enabled trigger. LED state
-changes are suspended while the driver is in suspend state. Any timers
-that are active at the time driver gets suspended, continue to run, without
-being able to actually change the LED state. Once driver is resumed, triggers
-start functioning again.
-
-LED state changes are controlled using brightness which is a common led
-class device property. When brightness is set to 0 from user space via
-echo 0 > brightness, it will result in deactivating the current trigger.
-
-Transient trigger uses standard register and unregister interfaces. During
-trigger registration, for each led class device that specifies this trigger
-as its default trigger, trigger activation routine will get called. During
-registration, the LED state does not change, unless there is another trigger
-active, in which case LED state changes to LED_OFF.
-
-During trigger unregistration, LED state gets changed to LED_OFF.
-
-Transient trigger activation routine doesn't change the LED state. It
-creates its properties and does its initialization. Transient trigger
-deactivation routine, will cancel any timer that is active before it cleans
-up and removes the properties it created. It will restore the LED state to
-non-transient state. When driver gets suspended, irrespective of the transient
-state, the LED state changes to LED_OFF.
-
-Transient trigger can be enabled and disabled from user space on led class
-devices, that support this trigger as shown below:
-
-echo transient > trigger
-echo none > trigger
-
-NOTE: Add a new property trigger state to control the state.
-
-This trigger exports three properties, activate, state, and duration. When
-transient trigger is activated these properties are set to default values.
-
-- duration allows setting timer value in msecs. The initial value is 0.
-- activate allows activating and deactivating the timer specified by
- duration as needed. The initial and default value is 0. This will allow
- duration to be set after trigger activation.
-- state allows user to specify a transient state to be held for the specified
- duration.
-
- activate - one shot timer activate mechanism.
- 1 when activated, 0 when deactivated.
- default value is zero when transient trigger is enabled,
- to allow duration to be set.
-
- activate state indicates a timer with a value of specified
- duration running.
- deactivated state indicates that there is no active timer
- running.
-
- duration - one shot timer value. When activate is set, duration value
- is used to start a timer that runs once. This value doesn't
- get changed by the trigger unless user does a set via
- echo new_value > duration
-
- state - transient state to be held. It has two values 0 or 1. 0 maps
- to LED_OFF and 1 maps to LED_FULL. The specified state is
- held for the duration of the one shot timer and then the
- state gets changed to the non-transient state which is the
- inverse of transient state.
- If state = LED_FULL, when the timer runs out the state will
- go back to LED_OFF.
- If state = LED_OFF, when the timer runs out the state will
- go back to LED_FULL.
- Please note that current LED state is not checked prior to
- changing the state to the specified state.
- Driver could map these values to inverted depending on the
- default states it defines for the LED in its brightness_set()
- interface which is called from the led brightness_set()
- interfaces to control the LED state.
-
-When timer expires activate goes back to deactivated state, duration is left
-at the set value to be used when activate is set at a future time. This will
-allow user app to set the time once and activate it to run it once for the
-specified value as needed. When timer expires, state is restored to the
-non-transient state which is the inverse of the transient state.
-
- echo 1 > activate - starts timer = duration when duration is not 0.
- echo 0 > activate - cancels currently running timer.
- echo n > duration - stores timer value to be used upon next
- activate. Currently active timer if
- any, continues to run for the specified time.
- echo 0 > duration - stores timer value to be used upon next
- activate. Currently active timer if any,
- continues to run for the specified time.
- echo 1 > state - stores desired transient state LED_FULL to be
- held for the specified duration.
- echo 0 > state - stores desired transient state LED_OFF to be
- held for the specified duration.
-
-What is not supported:
-======================
-- Timer activation is one shot and extending and/or shortening the timer
- is not supported.
-
-Example use-case 1:
- echo transient > trigger
- echo n > duration
- echo 1 > state
-repeat the following step as needed:
- echo 1 > activate - start timer = duration to run once
- echo 1 > activate - start timer = duration to run once
- echo none > trigger
-
-This trigger is intended to be used for for the following example use cases:
- - Control of vibrate (phones, tablets etc.) hardware by user space app.
- - Use of LED by user space app as activity indicator.
- - Use of LED by user space app as a kind of watchdog indicator -- as
- long as the app is alive, it can keep the LED illuminated, if it dies
- the LED will be extinguished automatically.
- - Use by any user space app that needs a transient GPIO output.
--- /dev/null
+====================
+USB port LED trigger
+====================
+
+This LED trigger can be used for signalling to the user a presence of USB device
+in a given port. It simply turns on LED when device appears and turns it off
+when it disappears.
+
+It requires selecting USB ports that should be observed. All available ones are
+listed as separated entries in a "ports" subdirectory. Selecting is handled by
+echoing "1" to a chosen port.
+
+Please note that this trigger allows selecting multiple USB ports for a single
+LED.
+
+This can be useful in two cases:
+
+1) Device with single USB LED and few physical ports
+====================================================
+
+In such a case LED will be turned on as long as there is at least one connected
+USB device.
+
+2) Device with a physical port handled by few controllers
+=========================================================
+
+Some devices may have one controller per PHY standard. E.g. USB 3.0 physical
+port may be handled by ohci-platform, ehci-platform and xhci-hcd. If there is
+only one LED user will most likely want to assign ports from all 3 hubs.
+
+
+This trigger can be activated from user space on led class devices as shown
+below::
+
+ echo usbport > trigger
+
+This adds sysfs attributes to the LED that are documented in:
+Documentation/ABI/testing/sysfs-class-led-trigger-usbport
+
+Example use-case::
+
+ echo usbport > trigger
+ echo 1 > ports/usb1-port1
+ echo 1 > ports/usb2-port1
+ cat ports/usb1-port1
+ echo 0 > ports/usb1-port1
+++ /dev/null
-USB port LED trigger
-====================
-
-This LED trigger can be used for signalling to the user a presence of USB device
-in a given port. It simply turns on LED when device appears and turns it off
-when it disappears.
-
-It requires selecting USB ports that should be observed. All available ones are
-listed as separated entries in a "ports" subdirectory. Selecting is handled by
-echoing "1" to a chosen port.
-
-Please note that this trigger allows selecting multiple USB ports for a single
-LED. This can be useful in two cases:
-
-1) Device with single USB LED and few physical ports
-
-In such a case LED will be turned on as long as there is at least one connected
-USB device.
-
-2) Device with a physical port handled by few controllers
-
-Some devices may have one controller per PHY standard. E.g. USB 3.0 physical
-port may be handled by ohci-platform, ehci-platform and xhci-hcd. If there is
-only one LED user will most likely want to assign ports from all 3 hubs.
-
-
-This trigger can be activated from user space on led class devices as shown
-below:
-
- echo usbport > trigger
-
-This adds sysfs attributes to the LED that are documented in:
-Documentation/ABI/testing/sysfs-class-led-trigger-usbport
-
-Example use-case:
-
- echo usbport > trigger
- echo 1 > ports/usb1-port1
- echo 1 > ports/usb2-port1
- cat ports/usb1-port1
- echo 0 > ports/usb1-port1
--- /dev/null
+==============
+Userspace LEDs
+==============
+
+The uleds driver supports userspace LEDs. This can be useful for testing
+triggers and can also be used to implement virtual LEDs.
+
+
+Usage
+=====
+
+When the driver is loaded, a character device is created at /dev/uleds. To
+create a new LED class device, open /dev/uleds and write a uleds_user_dev
+structure to it (found in kernel public header file linux/uleds.h)::
+
+ #define LED_MAX_NAME_SIZE 64
+
+ struct uleds_user_dev {
+ char name[LED_MAX_NAME_SIZE];
+ };
+
+A new LED class device will be created with the name given. The name can be
+any valid sysfs device node name, but consider using the LED class naming
+convention of "devicename:color:function".
+
+The current brightness is found by reading a single byte from the character
+device. Values are unsigned: 0 to 255. Reading will block until the brightness
+changes. The device node can also be polled to notify when the brightness value
+changes.
+
+The LED class device will be removed when the open file handle to /dev/uleds
+is closed.
+
+Multiple LED class devices are created by opening additional file handles to
+/dev/uleds.
+
+See tools/leds/uledmon.c for an example userspace program.
+++ /dev/null
-Userspace LEDs
-==============
-
-The uleds driver supports userspace LEDs. This can be useful for testing
-triggers and can also be used to implement virtual LEDs.
-
-
-Usage
-=====
-
-When the driver is loaded, a character device is created at /dev/uleds. To
-create a new LED class device, open /dev/uleds and write a uleds_user_dev
-structure to it (found in kernel public header file linux/uleds.h).
-
- #define LED_MAX_NAME_SIZE 64
-
- struct uleds_user_dev {
- char name[LED_MAX_NAME_SIZE];
- };
-
-A new LED class device will be created with the name given. The name can be
-any valid sysfs device node name, but consider using the LED class naming
-convention of "devicename:color:function".
-
-The current brightness is found by reading a single byte from the character
-device. Values are unsigned: 0 to 255. Reading will block until the brightness
-changes. The device node can also be polled to notify when the brightness value
-changes.
-
-The LED class device will be removed when the open file handle to /dev/uleds
-is closed.
-
-Multiple LED class devices are created by opening additional file handles to
-/dev/uleds.
-
-See tools/leds/uledmon.c for an example userspace program.
S: Supported
F: drivers/leds/leds-mlxcpld.c
F: drivers/leds/leds-mlxreg.c
-F: Documentation/leds/leds-mlxcpld.txt
+F: Documentation/leds/leds-mlxcpld.rst
MELLANOX PLATFORM DRIVER
M: Vadim Pasternak <vadimp@mellanox.com>
This allows LEDs to be controlled by a programmable timer
via sysfs. Some LED hardware can be programmed to start
blinking the LED without any further software interaction.
- For more details read Documentation/leds/leds-class.txt.
+ For more details read Documentation/leds/leds-class.rst.
If unsure, say Y.
// LED Kernel Transient Trigger
//
// Transient trigger allows one shot timer activation. Please refer to
-// Documentation/leds/ledtrig-transient.txt for details
+// Documentation/leds/ledtrig-transient.rst for details
// Copyright (C) 2012 Shuah Khan <shuahkhan@gmail.com>
//
// Based on Richard Purdie's ledtrig-timer.c and Atsushi Nemoto's
echo netfilter-ssh > /sys/class/leds/<ledname>/trigger
For more information on the LEDs available on your system, see
- Documentation/leds/leds-class.txt
+ Documentation/leds/leds-class.rst
config NETFILTER_XT_TARGET_LOG
tristate "LOG target support"
projects / linux.git / commitdiff