return noffset;
}
+static size_t ieee80211_assoc_link_elems(struct ieee80211_sub_if_data *sdata,
+ struct sk_buff *skb, u16 *capab,
+ const struct element *ext_capa,
+ const u8 *extra_elems,
+ size_t extra_elems_len,
+ struct ieee80211_link_data *link)
+{
+ enum nl80211_iftype iftype = ieee80211_vif_type_p2p(&sdata->vif);
+ struct ieee80211_if_managed *ifmgd = &sdata->u.mgd;
+ struct ieee80211_mgd_assoc_data *assoc_data = ifmgd->assoc_data;
+ struct cfg80211_bss *cbss = assoc_data->bss;
+ struct ieee80211_channel *chan = cbss->channel;
+ const struct ieee80211_sband_iftype_data *iftd;
+ struct ieee80211_local *local = sdata->local;
+ struct ieee80211_supported_band *sband;
+ enum nl80211_chan_width width = NL80211_CHAN_WIDTH_20;
+ struct ieee80211_chanctx_conf *chanctx_conf;
+ size_t offset = 0;
+ u8 *pos;
+ int i;
+
+ /*
+ * 5/10 MHz scenarios are only viable without MLO, in which
+ * case this pointer should be used ... All of this is a bit
+ * unclear though, not sure this even works at all.
+ */
+ rcu_read_lock();
+ chanctx_conf = rcu_dereference(link->conf->chanctx_conf);
+ if (chanctx_conf)
+ width = chanctx_conf->def.width;
+ rcu_read_unlock();
+
+ sband = local->hw.wiphy->bands[chan->band];
+ iftd = ieee80211_get_sband_iftype_data(sband, iftype);
+
+ if (sband->band == NL80211_BAND_2GHZ) {
+ *capab |= WLAN_CAPABILITY_SHORT_SLOT_TIME;
+ *capab |= WLAN_CAPABILITY_SHORT_PREAMBLE;
+ }
+
+ if ((cbss->capability & WLAN_CAPABILITY_SPECTRUM_MGMT) &&
+ ieee80211_hw_check(&local->hw, SPECTRUM_MGMT))
+ *capab |= WLAN_CAPABILITY_SPECTRUM_MGMT;
+
+ if (sband->band != NL80211_BAND_S1GHZ)
+ ieee80211_assoc_add_rates(skb, width, sband, assoc_data);
+
+ if (*capab & WLAN_CAPABILITY_SPECTRUM_MGMT ||
+ *capab & WLAN_CAPABILITY_RADIO_MEASURE) {
+ struct cfg80211_chan_def chandef = {
+ .width = width,
+ .chan = chan,
+ };
+
+ pos = skb_put(skb, 4);
+ *pos++ = WLAN_EID_PWR_CAPABILITY;
+ *pos++ = 2;
+ *pos++ = 0; /* min tx power */
+ /* max tx power */
+ *pos++ = ieee80211_chandef_max_power(&chandef);
+ }
+
+ /*
+ * Per spec, we shouldn't include the list of channels if we advertise
+ * support for extended channel switching, but we've always done that;
+ * (for now?) apply this restriction only on the (new) 6 GHz band.
+ */
+ if (*capab & WLAN_CAPABILITY_SPECTRUM_MGMT &&
+ (sband->band != NL80211_BAND_6GHZ ||
+ !ext_capa || ext_capa->datalen < 1 ||
+ !(ext_capa->data[0] & WLAN_EXT_CAPA1_EXT_CHANNEL_SWITCHING))) {
+ /* TODO: get this in reg domain format */
+ pos = skb_put(skb, 2 * sband->n_channels + 2);
+ *pos++ = WLAN_EID_SUPPORTED_CHANNELS;
+ *pos++ = 2 * sband->n_channels;
+ for (i = 0; i < sband->n_channels; i++) {
+ int cf = sband->channels[i].center_freq;
+
+ *pos++ = ieee80211_frequency_to_channel(cf);
+ *pos++ = 1; /* one channel in the subband*/
+ }
+ }
+
+ /* if present, add any custom IEs that go before HT */
+ offset = ieee80211_add_before_ht_elems(skb, extra_elems,
+ extra_elems_len,
+ offset);
+
+ if (sband->band != NL80211_BAND_6GHZ &&
+ !(link->u.mgd.conn_flags & IEEE80211_CONN_DISABLE_HT))
+ ieee80211_add_ht_ie(sdata, skb,
+ assoc_data->ap_ht_param,
+ sband, chan, link->smps_mode,
+ link->u.mgd.conn_flags);
+
+ /* if present, add any custom IEs that go before VHT */
+ offset = ieee80211_add_before_vht_elems(skb, extra_elems,
+ extra_elems_len,
+ offset);
+
+ if (sband->band != NL80211_BAND_6GHZ &&
+ !(link->u.mgd.conn_flags & IEEE80211_CONN_DISABLE_VHT))
+ link->conf->mu_mimo_owner =
+ ieee80211_add_vht_ie(sdata, skb, sband,
+ &assoc_data->ap_vht_cap,
+ link->u.mgd.conn_flags);
+
+ /*
+ * If AP doesn't support HT, mark HE and EHT as disabled.
+ * If on the 5GHz band, make sure it supports VHT.
+ */
+ if (link->u.mgd.conn_flags & IEEE80211_CONN_DISABLE_HT ||
+ (sband->band == NL80211_BAND_5GHZ &&
+ link->u.mgd.conn_flags & IEEE80211_CONN_DISABLE_VHT))
+ link->u.mgd.conn_flags |=
+ IEEE80211_CONN_DISABLE_HE |
+ IEEE80211_CONN_DISABLE_EHT;
+
+ /* if present, add any custom IEs that go before HE */
+ offset = ieee80211_add_before_he_elems(skb, extra_elems,
+ extra_elems_len,
+ offset);
+
+ if (!(link->u.mgd.conn_flags & IEEE80211_CONN_DISABLE_HE))
+ ieee80211_add_he_ie(sdata, skb, sband,
+ link->u.mgd.conn_flags);
+
+ if (!(link->u.mgd.conn_flags & IEEE80211_CONN_DISABLE_EHT))
+ ieee80211_add_eht_ie(sdata, skb, sband);
+
+ if (sband->band == NL80211_BAND_S1GHZ) {
+ ieee80211_add_aid_request_ie(sdata, skb);
+ ieee80211_add_s1g_capab_ie(sdata, &sband->s1g_cap, skb);
+ }
+
+ if (iftd && iftd->vendor_elems.data && iftd->vendor_elems.len)
+ skb_put_data(skb, iftd->vendor_elems.data, iftd->vendor_elems.len);
+
+ return offset;
+}
+
static int ieee80211_send_assoc(struct ieee80211_sub_if_data *sdata)
{
struct ieee80211_local *local = sdata->local;
struct ieee80211_if_managed *ifmgd = &sdata->u.mgd;
struct ieee80211_mgd_assoc_data *assoc_data = ifmgd->assoc_data;
+ struct ieee80211_link_data *link = &sdata->deflink;
struct sk_buff *skb;
struct ieee80211_mgmt *mgmt;
u8 *pos, qos_info, *ie_start;
- size_t offset = 0, noffset;
- int i;
- u16 capab;
+ size_t offset, noffset;
+ u16 capab = WLAN_CAPABILITY_ESS;
struct ieee80211_supported_band *sband;
struct ieee80211_chanctx_conf *chanctx_conf;
struct ieee80211_channel *chan;
enum nl80211_iftype iftype = ieee80211_vif_type_p2p(&sdata->vif);
const struct ieee80211_sband_iftype_data *iftd;
struct ieee80211_prep_tx_info info = {};
- struct ieee80211_link_data *link = &sdata->deflink;
+ void *capab_pos;
int ret;
/* we know it's writable, cast away the const */
skb_reserve(skb, local->hw.extra_tx_headroom);
- capab = WLAN_CAPABILITY_ESS;
-
- if (sband->band == NL80211_BAND_2GHZ) {
- capab |= WLAN_CAPABILITY_SHORT_SLOT_TIME;
- capab |= WLAN_CAPABILITY_SHORT_PREAMBLE;
- }
-
if (assoc_data->capability & WLAN_CAPABILITY_PRIVACY)
capab |= WLAN_CAPABILITY_PRIVACY;
- if ((assoc_data->capability & WLAN_CAPABILITY_SPECTRUM_MGMT) &&
- ieee80211_hw_check(&local->hw, SPECTRUM_MGMT))
- capab |= WLAN_CAPABILITY_SPECTRUM_MGMT;
-
if (ifmgd->flags & IEEE80211_STA_ENABLE_RRM)
capab |= WLAN_CAPABILITY_RADIO_MEASURE;
+ /* Set MBSSID support for HE AP if needed */
+ if (ieee80211_hw_check(&local->hw, SUPPORTS_ONLY_HE_MULTI_BSSID) &&
+ !(link->u.mgd.conn_flags & IEEE80211_CONN_DISABLE_HE) &&
+ ext_capa && ext_capa->datalen >= 3)
+ ext_capa->data[2] |= WLAN_EXT_CAPA3_MULTI_BSSID_SUPPORT;
+
mgmt = skb_put_zero(skb, 24);
memcpy(mgmt->da, assoc_data->bss->bssid, ETH_ALEN);
memcpy(mgmt->sa, sdata->vif.addr, ETH_ALEN);
skb_put(skb, 10);
mgmt->frame_control = cpu_to_le16(IEEE80211_FTYPE_MGMT |
IEEE80211_STYPE_REASSOC_REQ);
- mgmt->u.reassoc_req.capab_info = cpu_to_le16(capab);
+ capab_pos = &mgmt->u.reassoc_req.capab_info;
mgmt->u.reassoc_req.listen_interval = listen_int;
memcpy(mgmt->u.reassoc_req.current_ap, assoc_data->prev_bssid,
ETH_ALEN);
skb_put(skb, 4);
mgmt->frame_control = cpu_to_le16(IEEE80211_FTYPE_MGMT |
IEEE80211_STYPE_ASSOC_REQ);
- mgmt->u.assoc_req.capab_info = cpu_to_le16(capab);
+ capab_pos = &mgmt->u.assoc_req.capab_info;
mgmt->u.assoc_req.listen_interval = listen_int;
info.subtype = IEEE80211_STYPE_ASSOC_REQ;
}
*pos++ = assoc_data->ssid_len;
memcpy(pos, assoc_data->ssid, assoc_data->ssid_len);
- if (sband->band != NL80211_BAND_S1GHZ)
- ieee80211_assoc_add_rates(skb, chanctx_conf->def.width,
- sband, assoc_data);
-
- if (capab & WLAN_CAPABILITY_SPECTRUM_MGMT ||
- capab & WLAN_CAPABILITY_RADIO_MEASURE) {
- pos = skb_put(skb, 4);
- *pos++ = WLAN_EID_PWR_CAPABILITY;
- *pos++ = 2;
- *pos++ = 0; /* min tx power */
- /* max tx power */
- *pos++ = ieee80211_chandef_max_power(&chanctx_conf->def);
- }
-
- /*
- * Per spec, we shouldn't include the list of channels if we advertise
- * support for extended channel switching, but we've always done that;
- * (for now?) apply this restriction only on the (new) 6 GHz band.
- */
- if (capab & WLAN_CAPABILITY_SPECTRUM_MGMT &&
- (sband->band != NL80211_BAND_6GHZ ||
- !ext_capa || ext_capa->datalen < 1 ||
- !(ext_capa->data[0] & WLAN_EXT_CAPA1_EXT_CHANNEL_SWITCHING))) {
- /* TODO: get this in reg domain format */
- pos = skb_put(skb, 2 * sband->n_channels + 2);
- *pos++ = WLAN_EID_SUPPORTED_CHANNELS;
- *pos++ = 2 * sband->n_channels;
- for (i = 0; i < sband->n_channels; i++) {
- int cf = sband->channels[i].center_freq;
-
- *pos++ = ieee80211_frequency_to_channel(cf);
- *pos++ = 1; /* one channel in the subband*/
- }
- }
+ /* add the elements for the assoc (main) link */
+ offset = ieee80211_assoc_link_elems(sdata, skb, &capab,
+ ext_capa,
+ assoc_data->ie,
+ assoc_data->ie_len,
+ link);
+ put_unaligned_le16(capab, capab_pos);
- /* Set MBSSID support for HE AP if needed */
- if (ieee80211_hw_check(&local->hw, SUPPORTS_ONLY_HE_MULTI_BSSID) &&
- !(link->u.mgd.conn_flags & IEEE80211_CONN_DISABLE_HE) &&
- ext_capa && ext_capa->datalen >= 3)
- ext_capa->data[2] |= WLAN_EXT_CAPA3_MULTI_BSSID_SUPPORT;
-
- /* if present, add any custom IEs that go before HT */
- offset = ieee80211_add_before_ht_elems(skb, assoc_data->ie,
- assoc_data->ie_len,
- offset);
-
- if (WARN_ON_ONCE((link->u.mgd.conn_flags & IEEE80211_CONN_DISABLE_HT) &&
- !(link->u.mgd.conn_flags & IEEE80211_CONN_DISABLE_VHT)))
- link->u.mgd.conn_flags |= IEEE80211_CONN_DISABLE_VHT;
-
- if (sband->band != NL80211_BAND_6GHZ &&
- !(link->u.mgd.conn_flags & IEEE80211_CONN_DISABLE_HT))
- ieee80211_add_ht_ie(sdata, skb, assoc_data->ap_ht_param,
- sband, chan, link->smps_mode,
- link->u.mgd.conn_flags);
-
- /* if present, add any custom IEs that go before VHT */
- offset = ieee80211_add_before_vht_elems(skb, assoc_data->ie,
- assoc_data->ie_len,
- offset);
-
- if (sband->band != NL80211_BAND_6GHZ &&
- !(link->u.mgd.conn_flags & IEEE80211_CONN_DISABLE_VHT))
- link->conf->mu_mimo_owner =
- ieee80211_add_vht_ie(sdata, skb, sband,
- &assoc_data->ap_vht_cap,
- link->u.mgd.conn_flags);
-
- /*
- * If AP doesn't support HT, mark HE and EHT as disabled.
- * If on the 5GHz band, make sure it supports VHT.
- */
- if (link->u.mgd.conn_flags & IEEE80211_CONN_DISABLE_HT ||
- (sband->band == NL80211_BAND_5GHZ &&
- link->u.mgd.conn_flags & IEEE80211_CONN_DISABLE_VHT))
- link->u.mgd.conn_flags |= IEEE80211_CONN_DISABLE_HE |
- IEEE80211_CONN_DISABLE_EHT;
-
- /* if present, add any custom IEs that go before HE */
- offset = ieee80211_add_before_he_elems(skb, assoc_data->ie,
- assoc_data->ie_len,
- offset);
-
- if (!(link->u.mgd.conn_flags & IEEE80211_CONN_DISABLE_HE)) {
- ieee80211_add_he_ie(sdata, skb, sband, link->u.mgd.conn_flags);
-
- if (!(link->u.mgd.conn_flags & IEEE80211_CONN_DISABLE_EHT))
- ieee80211_add_eht_ie(sdata, skb, sband);
- }
-
- /* if present, add any custom non-vendor IEs that go after HE */
+ /* if present, add any custom non-vendor IEs */
if (assoc_data->ie_len) {
noffset = ieee80211_ie_split_vendor(assoc_data->ie,
assoc_data->ie_len,
pos = ieee80211_add_wmm_info_ie(skb_put(skb, 9), qos_info);
}
- if (sband->band == NL80211_BAND_S1GHZ) {
- ieee80211_add_aid_request_ie(sdata, skb);
- ieee80211_add_s1g_capab_ie(sdata, &sband->s1g_cap, skb);
- }
-
- if (iftd && iftd->vendor_elems.data && iftd->vendor_elems.len)
- skb_put_data(skb, iftd->vendor_elems.data, iftd->vendor_elems.len);
-
/* add any remaining custom (i.e. vendor specific here) IEs */
if (assoc_data->ie_len) {
noffset = assoc_data->ie_len;
projects / linux.git / commitdiff