arm64: dts: qcom: msm8916: Define regulator constraints next to usage

Right now each MSM8916 device has a huge block of regulator constraints
with allowed voltages for each regulator. For lack of better
documentation these voltages are often copied as-is from the vendor
device tree, without much extra thought.

Unfortunately, the voltages in the vendor device trees are often
misleading or even wrong, e.g. because:

 - There is a large voltage range allowed and the actual voltage is
   only set somewhere hidden in some messy vendor driver. This is often
   the case for pm8916_{l14,l15,l16} because they have a broad range of
   1.8-3.3V by default.

 - The voltage is actually wrong but thanks to the voltage constraints
   in the RPM firmware it still ends up applying the correct voltage.

To have proper regulator constraints it is important to review them in
context of the usage. The current setup in the MSM8916 device trees
makes this quite hard because each device duplicates the standard
voltages for components of the SoC and mixes those with minor
device-specific additions and dummy voltages for completely unused
regulators.

The actual usage of the regulators for the SoC components is in
msm8916-pm8916.dtsi, so it can and should also define the related
voltage constraints. These are not board-specific but defined in the
APQ8016E/PM8916 Device Specification. The board DT can then focus on
describing the actual board-specific regulators, which makes it much
easier to review and spot potential mistakes there.

Note that this commit does not make any functional change. All used
regulators still have the same regulator constraints as before. Unused
regulators do not have regulator constraints anymore because most of
these were too broad or even entirely wrong. They should be added back
with proper voltage constraints when there is an actual usage.

Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230510-msm8916-regulators-v1-7-54d4960a05fc@gerhold.net

diff --git a/arch/arm64/boot/dts/qcom/apq8016-sbc.dts b/arch/arm64/boot/dts/qcom/apq8016-sbc.dts
index 7d7af6406c393e0e27f9b04259691b3c23d903fa..ab8dfd858025c29c9c1e0afee70e2fabacb50f9c 100644 (file)
--- a/arch/arm64/boot/dts/qcom/apq8016-sbc.dts
+++ b/arch/arm64/boot/dts/qcom/apq8016-sbc.dts
@@ -329,6 +329,40 @@
        linux,code = <KEY_VOLUMEDOWN>;
 };
 
+&pm8916_rpm_regulators {
+       /*
+        * The 96Boards specification expects a 1.8V power rail on the low-speed
+        * expansion connector that is able to provide at least 0.18W / 100 mA.
+        * L15/L16 are connected in parallel to provide 55 mA each. A minimum load
+        * must be specified to ensure the regulators are not put in LPM where they
+        * would only provide 5 mA.
+        */
+       pm8916_l15: l15 {
+               regulator-min-microvolt = <1800000>;
+               regulator-max-microvolt = <1800000>;
+               regulator-system-load = <50000>;
+               regulator-allow-set-load;
+               regulator-always-on;
+       };
+       pm8916_l16: l16 {
+               regulator-min-microvolt = <1800000>;
+               regulator-max-microvolt = <1800000>;
+               regulator-system-load = <50000>;
+               regulator-allow-set-load;
+               regulator-always-on;
+       };
+
+       pm8916_l17: l17 {
+               regulator-min-microvolt = <3300000>;
+               regulator-max-microvolt = <3300000>;
+       };
+};
+
+&pm8916_s4 {
+       regulator-always-on;
+       regulator-boot-on;
+};
+
 &sdhc_1 {
        status = "okay";
 
@@ -446,125 +480,6 @@
 &stm { status = "okay"; };
 &tpiu { status = "okay"; };
 
-&smd_rpm_regulators {
-       vdd_l1_l2_l3-supply = <&pm8916_s3>;
-       vdd_l4_l5_l6-supply = <&pm8916_s4>;
-       vdd_l7-supply = <&pm8916_s4>;
-
-       s3 {
-               regulator-min-microvolt = <1250000>;
-               regulator-max-microvolt = <1350000>;
-       };
-
-       s4 {
-               regulator-min-microvolt = <1850000>;
-               regulator-max-microvolt = <2150000>;
-
-               regulator-always-on;
-               regulator-boot-on;
-       };
-
-       l1 {
-               regulator-min-microvolt = <1225000>;
-               regulator-max-microvolt = <1225000>;
-       };
-
-       l2 {
-               regulator-min-microvolt = <1200000>;
-               regulator-max-microvolt = <1200000>;
-       };
-
-       l4 {
-               regulator-min-microvolt = <2050000>;
-               regulator-max-microvolt = <2050000>;
-       };
-
-       l5 {
-               regulator-min-microvolt = <1800000>;
-               regulator-max-microvolt = <1800000>;
-       };
-
-       l6 {
-               regulator-min-microvolt = <1800000>;
-               regulator-max-microvolt = <1800000>;
-       };
-
-       l7 {
-               regulator-min-microvolt = <1800000>;
-               regulator-max-microvolt = <1800000>;
-       };
-
-       l8 {
-               regulator-min-microvolt = <2900000>;
-               regulator-max-microvolt = <2900000>;
-       };
-
-       l9 {
-               regulator-min-microvolt = <3300000>;
-               regulator-max-microvolt = <3300000>;
-       };
-
-       l10 {
-               regulator-min-microvolt = <2800000>;
-               regulator-max-microvolt = <2800000>;
-       };
-
-       l11 {
-               regulator-min-microvolt = <2950000>;
-               regulator-max-microvolt = <2950000>;
-               regulator-allow-set-load;
-               regulator-system-load = <200000>;
-       };
-
-       l12 {
-               regulator-min-microvolt = <1800000>;
-               regulator-max-microvolt = <2950000>;
-       };
-
-       l13 {
-               regulator-min-microvolt = <3075000>;
-               regulator-max-microvolt = <3075000>;
-       };
-
-       l14 {
-               regulator-min-microvolt = <1800000>;
-               regulator-max-microvolt = <3300000>;
-       };
-
-       /*
-        * The 96Boards specification expects a 1.8V power rail on the low-speed
-        * expansion connector that is able to provide at least 0.18W / 100 mA.
-        * L15/L16 are connected in parallel to provide 55 mA each. A minimum load
-        * must be specified to ensure the regulators are not put in LPM where they
-        * would only provide 5 mA.
-        */
-       l15 {
-               regulator-min-microvolt = <1800000>;
-               regulator-max-microvolt = <1800000>;
-               regulator-system-load = <50000>;
-               regulator-allow-set-load;
-               regulator-always-on;
-       };
-
-       l16 {
-               regulator-min-microvolt = <1800000>;
-               regulator-max-microvolt = <1800000>;
-               regulator-system-load = <50000>;
-               regulator-allow-set-load;
-               regulator-always-on;
-       };
-
-       l17 {
-               regulator-min-microvolt = <3300000>;
-               regulator-max-microvolt = <3300000>;
-       };
-
-       l18 {
-               regulator-min-microvolt = <2700000>;
-               regulator-max-microvolt = <2700000>;
-       };
-};
-
 /*
  * 2mA drive strength is not enough when connecting multiple
  * I2C devices with different pull up resistors.

diff --git a/arch/arm64/boot/dts/qcom/msm8916-acer-a1-724.dts b/arch/arm64/boot/dts/qcom/msm8916-acer-a1-724.dts
index 0d517804e44ed26cd55b06d4299ab3aae6e76c08..753413b48751a69ebf2eca79c4fd4f472d7f5e05 100644 (file)
--- a/arch/arm64/boot/dts/qcom/msm8916-acer-a1-724.dts
+++ b/arch/arm64/boot/dts/qcom/msm8916-acer-a1-724.dts
@@ -114,6 +114,18 @@
        status = "okay";
 };
 
+&pm8916_rpm_regulators {
+       pm8916_l16: l16 {
+               regulator-min-microvolt = <2900000>;
+               regulator-max-microvolt = <2900000>;
+       };
+
+       pm8916_l17: l17 {
+               regulator-min-microvolt = <2850000>;
+               regulator-max-microvolt = <2850000>;
+       };
+};
+
 &pm8916_vib {
        status = "okay";
 };
@@ -153,109 +165,6 @@
        compatible = "qcom,wcn3620";
 };
 
-&smd_rpm_regulators {
-       vdd_l1_l2_l3-supply = <&pm8916_s3>;
-       vdd_l4_l5_l6-supply = <&pm8916_s4>;
-       vdd_l7-supply = <&pm8916_s4>;
-
-       s3 {
-               regulator-min-microvolt = <1250000>;
-               regulator-max-microvolt = <1350000>;
-       };
-
-       s4 {
-               regulator-min-microvolt = <1850000>;
-               regulator-max-microvolt = <2150000>;
-       };
-
-       l1 {
-               regulator-min-microvolt = <1225000>;
-               regulator-max-microvolt = <1225000>;
-       };
-
-       l2 {
-               regulator-min-microvolt = <1200000>;
-               regulator-max-microvolt = <1200000>;
-       };
-
-       l4 {
-               regulator-min-microvolt = <2050000>;
-               regulator-max-microvolt = <2050000>;
-       };
-
-       l5 {
-               regulator-min-microvolt = <1800000>;
-               regulator-max-microvolt = <1800000>;
-       };
-
-       l6 {
-               regulator-min-microvolt = <1800000>;
-               regulator-max-microvolt = <1800000>;
-       };
-
-       l7 {
-               regulator-min-microvolt = <1800000>;
-               regulator-max-microvolt = <1800000>;
-       };
-
-       l8 {
-               regulator-min-microvolt = <2900000>;
-               regulator-max-microvolt = <2900000>;
-       };
-
-       l9 {
-               regulator-min-microvolt = <3300000>;
-               regulator-max-microvolt = <3300000>;
-       };
-
-       l10 {
-               regulator-min-microvolt = <2800000>;
-               regulator-max-microvolt = <2800000>;
-       };
-
-       l11 {
-               regulator-min-microvolt = <2950000>;
-               regulator-max-microvolt = <2950000>;
-               regulator-system-load = <200000>;
-               regulator-allow-set-load;
-       };
-
-       l12 {
-               regulator-min-microvolt = <1800000>;
-               regulator-max-microvolt = <2950000>;
-       };
-
-       l13 {
-               regulator-min-microvolt = <3075000>;
-               regulator-max-microvolt = <3075000>;
-       };
-
-       l14 {
-               regulator-min-microvolt = <1800000>;
-               regulator-max-microvolt = <3300000>;
-       };
-
-       l15 {
-               regulator-min-microvolt = <1800000>;
-               regulator-max-microvolt = <3300000>;
-       };
-
-       l16 {
-               regulator-min-microvolt = <2900000>;
-               regulator-max-microvolt = <2900000>;
-       };
-
-       l17 {
-               regulator-min-microvolt = <2850000>;
-               regulator-max-microvolt = <2850000>;
-       };
-
-       l18 {
-               regulator-min-microvolt = <2700000>;
-               regulator-max-microvolt = <2700000>;
-       };
-};
-
 &msmgpio {
        accel_int_default: accel-int-default-state {
                pins = "gpio115";

diff --git a/arch/arm64/boot/dts/qcom/msm8916-alcatel-idol347.dts b/arch/arm64/boot/dts/qcom/msm8916-alcatel-idol347.dts
index ddd64cc46998307660b8f2c018e544a18ff76629..4bfbad669b1ea15a79a8ac962be31edff99d5ce1 100644 (file)
--- a/arch/arm64/boot/dts/qcom/msm8916-alcatel-idol347.dts
+++ b/arch/arm64/boot/dts/qcom/msm8916-alcatel-idol347.dts
@@ -156,6 +156,13 @@
        linux,code = <KEY_VOLUMEDOWN>;
 };
 
+&pm8916_rpm_regulators {
+       pm8916_l17: l17 {
+               regulator-min-microvolt = <2850000>;
+               regulator-max-microvolt = <2850000>;
+       };
+};
+
 &pm8916_vib {
        status = "okay";
 };
@@ -195,109 +202,6 @@
        compatible = "qcom,wcn3620";
 };
 
-&smd_rpm_regulators {
-       vdd_l1_l2_l3-supply = <&pm8916_s3>;
-       vdd_l4_l5_l6-supply = <&pm8916_s4>;
-       vdd_l7-supply = <&pm8916_s4>;
-
-       s3 {
-               regulator-min-microvolt = <1250000>;
-               regulator-max-microvolt = <1350000>;
-       };
-
-       s4 {
-               regulator-min-microvolt = <1850000>;
-               regulator-max-microvolt = <2150000>;
-       };
-
-       l1 {
-               regulator-min-microvolt = <1225000>;
-               regulator-max-microvolt = <1225000>;
-       };
-
-       l2 {
-               regulator-min-microvolt = <1200000>;
-               regulator-max-microvolt = <1200000>;
-       };
-
-       l4 {
-               regulator-min-microvolt = <2050000>;
-               regulator-max-microvolt = <2050000>;
-       };
-
-       l5 {
-               regulator-min-microvolt = <1800000>;
-               regulator-max-microvolt = <1800000>;
-       };
-
-       l6 {
-               regulator-min-microvolt = <1800000>;
-               regulator-max-microvolt = <1800000>;
-       };
-
-       l7 {
-               regulator-min-microvolt = <1800000>;
-               regulator-max-microvolt = <1800000>;
-       };
-
-       l8 {
-               regulator-min-microvolt = <2900000>;
-               regulator-max-microvolt = <2900000>;
-       };
-
-       l9 {
-               regulator-min-microvolt = <3300000>;
-               regulator-max-microvolt = <3300000>;
-       };
-
-       l10 {
-               regulator-min-microvolt = <2800000>;
-               regulator-max-microvolt = <2800000>;
-       };
-
-       l11 {
-               regulator-min-microvolt = <2950000>;
-               regulator-max-microvolt = <2950000>;
-               regulator-allow-set-load;
-               regulator-system-load = <200000>;
-       };
-
-       l12 {
-               regulator-min-microvolt = <1800000>;
-               regulator-max-microvolt = <2950000>;
-       };
-
-       l13 {
-               regulator-min-microvolt = <3075000>;
-               regulator-max-microvolt = <3075000>;
-       };
-
-       l14 {
-               regulator-min-microvolt = <1800000>;
-               regulator-max-microvolt = <3300000>;
-       };
-
-       l15 {
-               regulator-min-microvolt = <1800000>;
-               regulator-max-microvolt = <3300000>;
-       };
-
-       l16 {
-               regulator-min-microvolt = <1800000>;
-               regulator-max-microvolt = <3300000>;
-       };
-
-       l17 {
-               regulator-min-microvolt = <2850000>;
-               regulator-max-microvolt = <2850000>;
-       };
-
-       l18 {
-               regulator-min-microvolt = <2700000>;
-               regulator-max-microvolt = <2700000>;
-       };
-};
-
 &msmgpio {
        accel_int_default: accel-int-default-state {
                pins = "gpio31";

diff --git a/arch/arm64/boot/dts/qcom/msm8916-asus-z00l.dts b/arch/arm64/boot/dts/qcom/msm8916-asus-z00l.dts
index 982457503a3cc84d8540ac011dda1ed485234ced..37755e8853958f40bed3f2dd88285091d1bc1f6a 100644 (file)
--- a/arch/arm64/boot/dts/qcom/msm8916-asus-z00l.dts
+++ b/arch/arm64/boot/dts/qcom/msm8916-asus-z00l.dts
@@ -128,6 +128,13 @@
        status = "okay";
 };
 
+&pm8916_rpm_regulators {
+       pm8916_l17: l17 {
+               regulator-min-microvolt = <2850000>;
+               regulator-max-microvolt = <2850000>;
+       };
+};
+
 &sdhc_1 {
        status = "okay";
 
@@ -163,109 +170,6 @@
        compatible = "qcom,wcn3620";
 };
 
-&smd_rpm_regulators {
-       vdd_l1_l2_l3-supply = <&pm8916_s3>;
-       vdd_l4_l5_l6-supply = <&pm8916_s4>;
-       vdd_l7-supply = <&pm8916_s4>;
-
-       s3 {
-               regulator-min-microvolt = <1250000>;
-               regulator-max-microvolt = <1350000>;
-       };
-
-       s4 {
-               regulator-min-microvolt = <1850000>;
-               regulator-max-microvolt = <2150000>;
-       };
-
-       l1 {
-               regulator-min-microvolt = <1225000>;
-               regulator-max-microvolt = <1225000>;
-       };
-
-       l2 {
-               regulator-min-microvolt = <1200000>;
-               regulator-max-microvolt = <1200000>;
-       };
-
-       l4 {
-               regulator-min-microvolt = <2050000>;
-               regulator-max-microvolt = <2050000>;
-       };
-
-       l5 {
-               regulator-min-microvolt = <1800000>;
-               regulator-max-microvolt = <1800000>;
-       };
-
-       l6 {
-               regulator-min-microvolt = <1800000>;
-               regulator-max-microvolt = <1800000>;
-       };
-
-       l7 {
-               regulator-min-microvolt = <1800000>;
-               regulator-max-microvolt = <1800000>;
-       };
-
-       l8 {
-               regulator-min-microvolt = <2900000>;
-               regulator-max-microvolt = <2900000>;
-       };
-
-       l9 {
-               regulator-min-microvolt = <3300000>;
-               regulator-max-microvolt = <3300000>;
-       };
-
-       l10 {
-               regulator-min-microvolt = <2800000>;
-               regulator-max-microvolt = <2800000>;
-       };
-
-       l11 {
-               regulator-min-microvolt = <2950000>;
-               regulator-max-microvolt = <2950000>;
-               regulator-allow-set-load;
-               regulator-system-load = <200000>;
-       };
-
-       l12 {
-               regulator-min-microvolt = <1800000>;
-               regulator-max-microvolt = <2950000>;
-       };
-
-       l13 {
-               regulator-min-microvolt = <3075000>;
-               regulator-max-microvolt = <3075000>;
-       };
-
-       l14 {
-               regulator-min-microvolt = <1800000>;
-               regulator-max-microvolt = <3300000>;
-       };
-
-       l15 {
-               regulator-min-microvolt = <1800000>;
-               regulator-max-microvolt = <3300000>;
-       };
-
-       l16 {
-               regulator-min-microvolt = <1800000>;
-               regulator-max-microvolt = <3300000>;
-       };
-
-       l17 {
-               regulator-min-microvolt = <2850000>;
-               regulator-max-microvolt = <2850000>;
-       };
-
-       l18 {
-               regulator-min-microvolt = <2700000>;
-               regulator-max-microvolt = <2700000>;
-       };
-};
-
 &msmgpio {
        gpio_keys_default: gpio-keys-default-state {
                pins = "gpio107", "gpio117";

diff --git a/arch/arm64/boot/dts/qcom/msm8916-gplus-fl8005a.dts b/arch/arm64/boot/dts/qcom/msm8916-gplus-fl8005a.dts
index 9584d271c5260c7792982e37ee1573958c023cd2..4a6bf99c755fd49f845a22dfa95969b281358e75 100644 (file)
--- a/arch/arm64/boot/dts/qcom/msm8916-gplus-fl8005a.dts
+++ b/arch/arm64/boot/dts/qcom/msm8916-gplus-fl8005a.dts
@@ -114,6 +114,13 @@
        status = "okay";
 };
 
+&pm8916_rpm_regulators {
+       pm8916_l17: l17 {
+               regulator-min-microvolt = <2850000>;
+               regulator-max-microvolt = <2850000>;
+       };
+};
+
 &pm8916_vib {
        status = "okay";
 };
@@ -153,109 +160,6 @@
        compatible = "qcom,wcn3620";
 };
 
-&smd_rpm_regulators {
-       vdd_l1_l2_l3-supply = <&pm8916_s3>;
-       vdd_l4_l5_l6-supply = <&pm8916_s4>;
-       vdd_l7-supply = <&pm8916_s4>;
-
-       s3 {
-               regulator-min-microvolt = <1250000>;
-               regulator-max-microvolt = <1350000>;
-       };
-
-       s4 {
-               regulator-min-microvolt = <1850000>;
-               regulator-max-microvolt = <2150000>;
-       };
-
-       l1 {
-               regulator-min-microvolt = <1225000>;
-               regulator-max-microvolt = <1225000>;
-       };
-
-       l2 {
-               regulator-min-microvolt = <1200000>;
-               regulator-max-microvolt = <1200000>;
-       };
-
-       l4 {
-               regulator-min-microvolt = <2050000>;
-               regulator-max-microvolt = <2050000>;
-       };
-
-       l5 {
-               regulator-min-microvolt = <1800000>;
-               regulator-max-microvolt = <1800000>;
-       };
-
-       l6 {
-               regulator-min-microvolt = <1800000>;
-               regulator-max-microvolt = <1800000>;
-       };
-
-       l7 {
-               regulator-min-microvolt = <1800000>;
-               regulator-max-microvolt = <1800000>;
-       };
-
-       l8 {
-               regulator-min-microvolt = <2900000>;
-               regulator-max-microvolt = <2900000>;
-       };
-
-       l9 {
-               regulator-min-microvolt = <3300000>;
-               regulator-max-microvolt = <3300000>;
-       };
-
-       l10 {
-               regulator-min-microvolt = <2800000>;
-               regulator-max-microvolt = <2800000>;
-       };
-
-       l11 {
-               regulator-min-microvolt = <2950000>;
-               regulator-max-microvolt = <2950000>;
-               regulator-system-load = <200000>;
-               regulator-allow-set-load;
-       };
-
-       l12 {
-               regulator-min-microvolt = <1800000>;
-               regulator-max-microvolt = <2950000>;
-       };
-
-       l13 {
-               regulator-min-microvolt = <3075000>;
-               regulator-max-microvolt = <3075000>;
-       };
-
-       l14 {
-               regulator-min-microvolt = <1800000>;
-               regulator-max-microvolt = <3300000>;
-       };
-
-       l15 {
-               regulator-min-microvolt = <1800000>;
-               regulator-max-microvolt = <3300000>;
-       };
-
-       l16 {
-               regulator-min-microvolt = <1800000>;
-               regulator-max-microvolt = <3300000>;
-       };
-
-       l17 {
-               regulator-min-microvolt = <2850000>;
-               regulator-max-microvolt = <2850000>;
-       };
-
-       l18 {
-               regulator-min-microvolt = <2700000>;
-               regulator-max-microvolt = <2700000>;
-       };
-};
-
 &msmgpio {
        camera_flash_default: camera-flash-default-state {
                pins = "gpio31", "gpio32";

diff --git a/arch/arm64/boot/dts/qcom/msm8916-huawei-g7.dts b/arch/arm64/boot/dts/qcom/msm8916-huawei-g7.dts
index 8197710372ad14548d2bf08da80d54a4f1c8975b..29aaa35438a3694e896fb3f941c7d6fd2381378e 100644 (file)
--- a/arch/arm64/boot/dts/qcom/msm8916-huawei-g7.dts
+++ b/arch/arm64/boot/dts/qcom/msm8916-huawei-g7.dts
@@ -222,11 +222,28 @@
        status = "okay";
 };
 
+&pm8916_l8 {
+       regulator-min-microvolt = <2950000>;
+       regulator-max-microvolt = <2950000>;
+};
+
 &pm8916_resin {
        status = "okay";
        linux,code = <KEY_VOLUMEDOWN>;
 };
 
+&pm8916_rpm_regulators {
+       pm8916_l16: l16 {
+               regulator-min-microvolt = <1800000>;
+               regulator-max-microvolt = <1800000>;
+       };
+
+       pm8916_l17: l17 {
+               regulator-min-microvolt = <2850000>;
+               regulator-max-microvolt = <2850000>;
+       };
+};
+
 &pm8916_vib {
        status = "okay";
 };
@@ -321,109 +338,6 @@
        compatible = "qcom,wcn3620";
 };
 
-&smd_rpm_regulators {
-       vdd_l1_l2_l3-supply = <&pm8916_s3>;
-       vdd_l4_l5_l6-supply = <&pm8916_s4>;
-       vdd_l7-supply = <&pm8916_s4>;
-
-       s3 {
-               regulator-min-microvolt = <1250000>;
-               regulator-max-microvolt = <1350000>;
-       };
-
-       s4 {
-               regulator-min-microvolt = <1850000>;
-               regulator-max-microvolt = <2150000>;
-       };
-
-       l1 {
-               regulator-min-microvolt = <1225000>;
-               regulator-max-microvolt = <1225000>;
-       };
-
-       l2 {
-               regulator-min-microvolt = <1200000>;
-               regulator-max-microvolt = <1200000>;
-       };
-
-       l4 {
-               regulator-min-microvolt = <2050000>;
-               regulator-max-microvolt = <2050000>;
-       };
-
-       l5 {
-               regulator-min-microvolt = <1800000>;
-               regulator-max-microvolt = <1800000>;
-       };
-
-       l6 {
-               regulator-min-microvolt = <1800000>;
-               regulator-max-microvolt = <1800000>;
-       };
-
-       l7 {
-               regulator-min-microvolt = <1800000>;
-               regulator-max-microvolt = <1800000>;
-       };
-
-       l8 {
-               regulator-min-microvolt = <2950000>;
-               regulator-max-microvolt = <2950000>;
-       };
-
-       l9 {
-               regulator-min-microvolt = <3300000>;
-               regulator-max-microvolt = <3300000>;
-       };
-
-       l10 {
-               regulator-min-microvolt = <2800000>;
-               regulator-max-microvolt = <2800000>;
-       };
-
-       l11 {
-               regulator-min-microvolt = <2950000>;
-               regulator-max-microvolt = <2950000>;
-               regulator-allow-set-load;
-               regulator-system-load = <200000>;
-       };
-
-       l12 {
-               regulator-min-microvolt = <1800000>;
-               regulator-max-microvolt = <2950000>;
-       };
-
-       l13 {
-               regulator-min-microvolt = <3075000>;
-               regulator-max-microvolt = <3075000>;
-       };
-
-       l14 {
-               regulator-min-microvolt = <1800000>;
-               regulator-max-microvolt = <3300000>;
-       };
-
-       l15 {
-               regulator-min-microvolt = <1800000>;
-               regulator-max-microvolt = <3300000>;
-       };
-
-       l16 {
-               regulator-min-microvolt = <1800000>;
-               regulator-max-microvolt = <1800000>;
-       };
-
-       l17 {
-               regulator-min-microvolt = <2850000>;
-               regulator-max-microvolt = <2850000>;
-       };
-
-       l18 {
-               regulator-min-microvolt = <2700000>;
-               regulator-max-microvolt = <2700000>;
-       };
-};
-
 &msmgpio {
        accel_irq_default: accel-irq-default-state {
                pins = "gpio115";

diff --git a/arch/arm64/boot/dts/qcom/msm8916-longcheer-l8150.dts b/arch/arm64/boot/dts/qcom/msm8916-longcheer-l8150.dts
index 68d1b76aaf772bafe950e0c3ab53f409fac43764..b7b1f1ceaf1f34450d52b49f0d691b9383eadd6f 100644 (file)
--- a/arch/arm64/boot/dts/qcom/msm8916-longcheer-l8150.dts
+++ b/arch/arm64/boot/dts/qcom/msm8916-longcheer-l8150.dts
@@ -223,6 +223,13 @@
        linux,code = <KEY_VOLUMEDOWN>;
 };
 
+&pm8916_rpm_regulators {
+       pm8916_l17: l17 {
+               regulator-min-microvolt = <2850000>;
+               regulator-max-microvolt = <2850000>;
+       };
+};
+
 &pm8916_usbin {
        status = "okay";
 };
@@ -267,109 +274,6 @@
        compatible = "qcom,wcn3620";
 };
 
-&smd_rpm_regulators {
-       vdd_l1_l2_l3-supply = <&pm8916_s3>;
-       vdd_l4_l5_l6-supply = <&pm8916_s4>;
-       vdd_l7-supply = <&pm8916_s4>;
-
-       s3 {
-               regulator-min-microvolt = <1250000>;
-               regulator-max-microvolt = <1350000>;
-       };
-
-       s4 {
-               regulator-min-microvolt = <1850000>;
-               regulator-max-microvolt = <2150000>;
-       };
-
-       l1 {
-               regulator-min-microvolt = <1225000>;
-               regulator-max-microvolt = <1225000>;
-       };
-
-       l2 {
-               regulator-min-microvolt = <1200000>;
-               regulator-max-microvolt = <1200000>;
-       };
-
-       l4 {
-               regulator-min-microvolt = <2050000>;
-               regulator-max-microvolt = <2050000>;
-       };
-
-       l5 {
-               regulator-min-microvolt = <1800000>;
-               regulator-max-microvolt = <1800000>;
-       };
-
-       l6 {
-               regulator-min-microvolt = <1800000>;
-               regulator-max-microvolt = <1800000>;
-       };
-
-       l7 {
-               regulator-min-microvolt = <1800000>;
-               regulator-max-microvolt = <1800000>;
-       };
-
-       l8 {
-               regulator-min-microvolt = <2900000>;
-               regulator-max-microvolt = <2900000>;
-       };
-
-       l9 {
-               regulator-min-microvolt = <3300000>;
-               regulator-max-microvolt = <3300000>;
-       };
-
-       l10 {
-               regulator-min-microvolt = <2800000>;
-               regulator-max-microvolt = <2800000>;
-       };
-
-       l11 {
-               regulator-min-microvolt = <2950000>;
-               regulator-max-microvolt = <2950000>;
-               regulator-allow-set-load;
-               regulator-system-load = <200000>;
-       };
-
-       l12 {
-               regulator-min-microvolt = <1800000>;
-               regulator-max-microvolt = <2950000>;
-       };
-
-       l13 {
-               regulator-min-microvolt = <3075000>;
-               regulator-max-microvolt = <3075000>;
-       };
-
-       l14 {
-               regulator-min-microvolt = <1800000>;
-               regulator-max-microvolt = <3300000>;
-       };
-
-       l15 {
-               regulator-min-microvolt = <1800000>;
-               regulator-max-microvolt = <3300000>;
-       };
-
-       l16 {
-               regulator-min-microvolt = <1800000>;
-               regulator-max-microvolt = <3300000>;
-       };
-
-       l17 {
-               regulator-min-microvolt = <2850000>;
-               regulator-max-microvolt = <2850000>;
-       };
-
-       l18 {
-               regulator-min-microvolt = <2700000>;
-               regulator-max-microvolt = <2700000>;
-       };
-};
-
 &msmgpio {
        accel_int_default: accel-int-default-state {
                pins = "gpio116";

diff --git a/arch/arm64/boot/dts/qcom/msm8916-longcheer-l8910.dts b/arch/arm64/boot/dts/qcom/msm8916-longcheer-l8910.dts
index 1e0c08770371adfd5d2cc81111fd140999787016..630727ed1ed5ad3e8a84df176c58cae184991212 100644 (file)
--- a/arch/arm64/boot/dts/qcom/msm8916-longcheer-l8910.dts
+++ b/arch/arm64/boot/dts/qcom/msm8916-longcheer-l8910.dts
@@ -110,6 +110,13 @@
        linux,code = <KEY_VOLUMEDOWN>;
 };
 
+&pm8916_rpm_regulators {
+       pm8916_l17: l17 {
+               regulator-min-microvolt = <2850000>;
+               regulator-max-microvolt = <2850000>;
+       };
+};
+
 &pm8916_vib {
        status = "okay";
 };
@@ -149,109 +156,6 @@
        compatible = "qcom,wcn3620";
 };
 
-&smd_rpm_regulators {
-       vdd_l1_l2_l3-supply = <&pm8916_s3>;
-       vdd_l4_l5_l6-supply = <&pm8916_s4>;
-       vdd_l7-supply = <&pm8916_s4>;
-
-       s3 {
-               regulator-min-microvolt = <1250000>;
-               regulator-max-microvolt = <1350000>;
-       };
-
-       s4 {
-               regulator-min-microvolt = <1850000>;
-               regulator-max-microvolt = <2150000>;
-       };
-
-       l1 {
-               regulator-min-microvolt = <1225000>;
-               regulator-max-microvolt = <1225000>;
-       };
-
-       l2 {
-               regulator-min-microvolt = <1200000>;
-               regulator-max-microvolt = <1200000>;
-       };
-
-       l4 {
-               regulator-min-microvolt = <2050000>;
-               regulator-max-microvolt = <2050000>;
-       };
-
-       l5 {
-               regulator-min-microvolt = <1800000>;
-               regulator-max-microvolt = <1800000>;
-       };
-
-       l6 {
-               regulator-min-microvolt = <1800000>;
-               regulator-max-microvolt = <1800000>;
-       };
-
-       l7 {
-               regulator-min-microvolt = <1800000>;
-               regulator-max-microvolt = <1800000>;
-       };
-
-       l8 {
-               regulator-min-microvolt = <2900000>;
-               regulator-max-microvolt = <2900000>;
-       };
-
-       l9 {
-               regulator-min-microvolt = <3300000>;
-               regulator-max-microvolt = <3300000>;
-       };
-
-       l10 {
-               regulator-min-microvolt = <2800000>;
-               regulator-max-microvolt = <2800000>;
-       };
-
-       l11 {
-               regulator-min-microvolt = <2950000>;
-               regulator-max-microvolt = <2950000>;
-               regulator-allow-set-load;
-               regulator-system-load = <200000>;
-       };
-
-       l12 {
-               regulator-min-microvolt = <1800000>;
-               regulator-max-microvolt = <2950000>;
-       };
-
-       l13 {
-               regulator-min-microvolt = <3075000>;
-               regulator-max-microvolt = <3075000>;
-       };
-
-       l14 {
-               regulator-min-microvolt = <1800000>;
-               regulator-max-microvolt = <3300000>;
-       };
-
-       l15 {
-               regulator-min-microvolt = <1800000>;
-               regulator-max-microvolt = <3300000>;
-       };
-
-       l16 {
-               regulator-min-microvolt = <1800000>;
-               regulator-max-microvolt = <3300000>;
-       };
-
-       l17 {
-               regulator-min-microvolt = <2850000>;
-               regulator-max-microvolt = <2850000>;
-       };
-
-       l18 {
-               regulator-min-microvolt = <2700000>;
-               regulator-max-microvolt = <2700000>;
-       };
-};
-
 &msmgpio {
        button_backlight_default: button-backlight-default-state {
                pins = "gpio17";

diff --git a/arch/arm64/boot/dts/qcom/msm8916-pm8916.dtsi b/arch/arm64/boot/dts/qcom/msm8916-pm8916.dtsi
index 29ef46c333506eac9325835d973c62042469eeb3..b38eecbd62538d9500a9c4098ad5abb73ce462e3 100644 (file)
--- a/arch/arm64/boot/dts/qcom/msm8916-pm8916.dtsi
+++ b/arch/arm64/boot/dts/qcom/msm8916-pm8916.dtsi
@@ -61,30 +61,92 @@
 };
 
 &rpm_requests {
-       smd_rpm_regulators: regulators {
+       pm8916_rpm_regulators: regulators {
                compatible = "qcom,rpm-pm8916-regulators";
+               vdd_l1_l2_l3-supply = <&pm8916_s3>;
+               vdd_l4_l5_l6-supply = <&pm8916_s4>;
+               vdd_l7-supply = <&pm8916_s4>;
 
                /* pm8916_s1 is managed by rpmpd (MSM8916_VDDCX) */
-               pm8916_s3: s3 {};
-               pm8916_s4: s4 {};
 
-               pm8916_l1: l1 {};
-               pm8916_l2: l2 {};
+               pm8916_s3: s3 {
+                       regulator-min-microvolt = <1250000>;
+                       regulator-max-microvolt = <1350000>;
+               };
+
+               pm8916_s4: s4 {
+                       regulator-min-microvolt = <1850000>;
+                       regulator-max-microvolt = <2150000>;
+               };
+
+               /*
+                * Some of the regulators are unused or managed by another
+                * processor (e.g. the modem). We should still define nodes for
+                * them to ensure the vote from the application processor can be
+                * dropped in case the regulators are already on during boot.
+                *
+                * The labels for these nodes are omitted on purpose because
+                * boards should configure a proper voltage before using them.
+                */
+               l1 {};
+
+               pm8916_l2: l2 {
+                       regulator-min-microvolt = <1200000>;
+                       regulator-max-microvolt = <1200000>;
+               };
+
                /* pm8916_l3 is managed by rpmpd (MSM8916_VDDMX) */
-               pm8916_l4: l4 {};
-               pm8916_l5: l5 {};
-               pm8916_l6: l6 {};
-               pm8916_l7: l7 {};
-               pm8916_l8: l8 {};
-               pm8916_l9: l9 {};
-               pm8916_l10: l10 {};
-               pm8916_l11: l11 {};
-               pm8916_l12: l12 {};
-               pm8916_l13: l13 {};
-               pm8916_l14: l14 {};
-               pm8916_l15: l15 {};
-               pm8916_l16: l16 {};
-               pm8916_l17: l17 {};
-               pm8916_l18: l18 {};
+
+               l4 {};
+
+               pm8916_l5: l5 {
+                       regulator-min-microvolt = <1800000>;
+                       regulator-max-microvolt = <1800000>;
+               };
+
+               pm8916_l6: l6 {
+                       regulator-min-microvolt = <1800000>;
+                       regulator-max-microvolt = <1800000>;
+               };
+
+               pm8916_l7: l7 {
+                       regulator-min-microvolt = <1800000>;
+                       regulator-max-microvolt = <1800000>;
+               };
+
+               pm8916_l8: l8 {
+                       regulator-min-microvolt = <2900000>;
+                       regulator-max-microvolt = <2900000>;
+               };
+
+               pm8916_l9: l9 {
+                       regulator-min-microvolt = <3300000>;
+                       regulator-max-microvolt = <3300000>;
+               };
+
+               l10 {};
+
+               pm8916_l11: l11 {
+                       regulator-min-microvolt = <2950000>;
+                       regulator-max-microvolt = <2950000>;
+                       regulator-allow-set-load;
+                       regulator-system-load = <200000>;
+               };
+
+               pm8916_l12: l12 {
+                       regulator-min-microvolt = <1800000>;
+                       regulator-max-microvolt = <2950000>;
+               };
+
+               pm8916_l13: l13 {
+                       regulator-min-microvolt = <3075000>;
+                       regulator-max-microvolt = <3075000>;
+               };
+
+               l14 {};
+               l15 {};
+               l16 {};
+               l17 {};
+               l18 {};
        };
 };

diff --git a/arch/arm64/boot/dts/qcom/msm8916-samsung-a2015-common.dtsi b/arch/arm64/boot/dts/qcom/msm8916-samsung-a2015-common.dtsi
index b362a76eebc94191866578c90c40e78711ea4d16..37a872949851b0401650aceeb1cc9a44f59ae02e 100644 (file)
--- a/arch/arm64/boot/dts/qcom/msm8916-samsung-a2015-common.dtsi
+++ b/arch/arm64/boot/dts/qcom/msm8916-samsung-a2015-common.dtsi
@@ -252,6 +252,13 @@
        linux,code = <KEY_VOLUMEDOWN>;
 };
 
+&pm8916_rpm_regulators {
+       pm8916_l17: l17 {
+               regulator-min-microvolt = <2850000>;
+               regulator-max-microvolt = <2850000>;
+       };
+};
+
 &sdhc_1 {
        status = "okay";
 
@@ -279,109 +286,6 @@
        extcon = <&muic>;
 };
 
-&smd_rpm_regulators {
-       vdd_l1_l2_l3-supply = <&pm8916_s3>;
-       vdd_l4_l5_l6-supply = <&pm8916_s4>;
-       vdd_l7-supply = <&pm8916_s4>;
-
-       s3 {
-               regulator-min-microvolt = <1250000>;
-               regulator-max-microvolt = <1350000>;
-       };
-
-       s4 {
-               regulator-min-microvolt = <1850000>;
-               regulator-max-microvolt = <2150000>;
-       };
-
-       l1 {
-               regulator-min-microvolt = <1225000>;
-               regulator-max-microvolt = <1225000>;
-       };
-
-       l2 {
-               regulator-min-microvolt = <1200000>;
-               regulator-max-microvolt = <1200000>;
-       };
-
-       l4 {
-               regulator-min-microvolt = <2050000>;
-               regulator-max-microvolt = <2050000>;
-       };
-
-       l5 {
-               regulator-min-microvolt = <1800000>;
-               regulator-max-microvolt = <1800000>;
-       };
-
-       l6 {
-               regulator-min-microvolt = <1800000>;
-               regulator-max-microvolt = <1800000>;
-       };
-
-       l7 {
-               regulator-min-microvolt = <1800000>;
-               regulator-max-microvolt = <1800000>;
-       };
-
-       l8 {
-               regulator-min-microvolt = <2900000>;
-               regulator-max-microvolt = <2900000>;
-       };
-
-       l9 {
-               regulator-min-microvolt = <3300000>;
-               regulator-max-microvolt = <3300000>;
-       };
-
-       l10 {
-               regulator-min-microvolt = <2800000>;
-               regulator-max-microvolt = <2800000>;
-       };
-
-       l11 {
-               regulator-min-microvolt = <2950000>;
-               regulator-max-microvolt = <2950000>;
-               regulator-allow-set-load;
-               regulator-system-load = <200000>;
-       };
-
-       l12 {
-               regulator-min-microvolt = <1800000>;
-               regulator-max-microvolt = <2950000>;
-       };
-
-       l13 {
-               regulator-min-microvolt = <3075000>;
-               regulator-max-microvolt = <3075000>;
-       };
-
-       l14 {
-               regulator-min-microvolt = <1800000>;
-               regulator-max-microvolt = <3300000>;
-       };
-
-       l15 {
-               regulator-min-microvolt = <1800000>;
-               regulator-max-microvolt = <3300000>;
-       };
-
-       l16 {
-               regulator-min-microvolt = <1800000>;
-               regulator-max-microvolt = <3300000>;
-       };
-
-       l17 {
-               regulator-min-microvolt = <2850000>;
-               regulator-max-microvolt = <2850000>;
-       };
-
-       l18 {
-               regulator-min-microvolt = <2700000>;
-               regulator-max-microvolt = <2700000>;
-       };
-};
-
 &msmgpio {
        accel_int_default: accel-int-default-state {
                pins = "gpio115";

diff --git a/arch/arm64/boot/dts/qcom/msm8916-samsung-gt5-common.dtsi b/arch/arm64/boot/dts/qcom/msm8916-samsung-gt5-common.dtsi
index 4464beeeaab1276e50665ebab5b9870dfa6ec4d2..a49e1641e59b827b9f8e87ba2bd0181a8d57d8aa 100644 (file)
--- a/arch/arm64/boot/dts/qcom/msm8916-samsung-gt5-common.dtsi
+++ b/arch/arm64/boot/dts/qcom/msm8916-samsung-gt5-common.dtsi
@@ -120,6 +120,13 @@
        status = "okay";
 };
 
+&pm8916_rpm_regulators {
+       pm8916_l17: l17 {
+               regulator-min-microvolt = <2850000>;
+               regulator-max-microvolt = <2850000>;
+       };
+};
+
 /* FIXME: Replace with MAX77849 MUIC when driver is available */
 &pm8916_usbin {
        status = "okay";
@@ -162,109 +169,6 @@
        compatible = "qcom,wcn3660b";
 };
 
-&smd_rpm_regulators {
-       vdd_l1_l2_l3-supply = <&pm8916_s3>;
-       vdd_l4_l5_l6-supply = <&pm8916_s4>;
-       vdd_l7-supply = <&pm8916_s4>;
-
-       s3 {
-               regulator-min-microvolt = <1250000>;
-               regulator-max-microvolt = <1350000>;
-       };
-
-       s4 {
-               regulator-min-microvolt = <1850000>;
-               regulator-max-microvolt = <2150000>;
-       };
-
-       l1 {
-               regulator-min-microvolt = <1225000>;
-               regulator-max-microvolt = <1225000>;
-       };
-
-       l2 {
-               regulator-min-microvolt = <1200000>;
-               regulator-max-microvolt = <1200000>;
-       };
-
-       l4 {
-               regulator-min-microvolt = <2050000>;
-               regulator-max-microvolt = <2050000>;
-       };
-
-       l5 {
-               regulator-min-microvolt = <1800000>;
-               regulator-max-microvolt = <1800000>;
-       };
-
-       l6 {
-               regulator-min-microvolt = <1800000>;
-               regulator-max-microvolt = <1800000>;
-       };
-
-       l7 {
-               regulator-min-microvolt = <1800000>;
-               regulator-max-microvolt = <1800000>;
-       };
-
-       l8 {
-               regulator-min-microvolt = <2900000>;
-               regulator-max-microvolt = <2900000>;
-       };
-
-       l9 {
-               regulator-min-microvolt = <3300000>;
-               regulator-max-microvolt = <3300000>;
-       };
-
-       l10 {
-               regulator-min-microvolt = <2800000>;
-               regulator-max-microvolt = <2800000>;
-       };
-
-       l11 {
-               regulator-min-microvolt = <2950000>;
-               regulator-max-microvolt = <2950000>;
-               regulator-system-load = <200000>;
-               regulator-allow-set-load;
-       };
-
-       l12 {
-               regulator-min-microvolt = <1800000>;
-               regulator-max-microvolt = <2950000>;
-       };
-
-       l13 {
-               regulator-min-microvolt = <3075000>;
-               regulator-max-microvolt = <3075000>;
-       };
-
-       l14 {
-               regulator-min-microvolt = <1800000>;
-               regulator-max-microvolt = <3300000>;
-       };
-
-       l15 {
-               regulator-min-microvolt = <1800000>;
-               regulator-max-microvolt = <3300000>;
-       };
-
-       l16 {
-               regulator-min-microvolt = <1800000>;
-               regulator-max-microvolt = <3300000>;
-       };
-
-       l17 {
-               regulator-min-microvolt = <2850000>;
-               regulator-max-microvolt = <2850000>;
-       };
-
-       l18 {
-               regulator-min-microvolt = <2700000>;
-               regulator-max-microvolt = <2700000>;
-       };
-};
-
 &msmgpio {
        accel_int_default: accel-int-default-state {
                pins = "gpio115";

diff --git a/arch/arm64/boot/dts/qcom/msm8916-samsung-j5-common.dtsi b/arch/arm64/boot/dts/qcom/msm8916-samsung-j5-common.dtsi
index 6e231e92e675652069bc30fea61e7ffd0c70af73..6192d04a58ae4c012da8be416d42ea8927b9bd71 100644 (file)
--- a/arch/arm64/boot/dts/qcom/msm8916-samsung-j5-common.dtsi
+++ b/arch/arm64/boot/dts/qcom/msm8916-samsung-j5-common.dtsi
@@ -128,109 +128,6 @@
        compatible = "qcom,wcn3620";
 };
 
-&smd_rpm_regulators {
-       vdd_l1_l2_l3-supply = <&pm8916_s3>;
-       vdd_l4_l5_l6-supply = <&pm8916_s4>;
-       vdd_l7-supply = <&pm8916_s4>;
-
-       s3 {
-               regulator-min-microvolt = <1250000>;
-               regulator-max-microvolt = <1350000>;
-       };
-
-       s4 {
-               regulator-min-microvolt = <1850000>;
-               regulator-max-microvolt = <2150000>;
-       };
-
-       l1 {
-               regulator-min-microvolt = <1225000>;
-               regulator-max-microvolt = <1225000>;
-       };
-
-       l2 {
-               regulator-min-microvolt = <1200000>;
-               regulator-max-microvolt = <1200000>;
-       };
-
-       l4 {
-               regulator-min-microvolt = <2050000>;
-               regulator-max-microvolt = <2050000>;
-       };
-
-       l5 {
-               regulator-min-microvolt = <1800000>;
-               regulator-max-microvolt = <1800000>;
-       };
-
-       l6 {
-               regulator-min-microvolt = <1800000>;
-               regulator-max-microvolt = <1800000>;
-       };
-
-       l7 {
-               regulator-min-microvolt = <1800000>;
-               regulator-max-microvolt = <1800000>;
-       };
-
-       l8 {
-               regulator-min-microvolt = <2900000>;
-               regulator-max-microvolt = <2900000>;
-       };
-
-       l9 {
-               regulator-min-microvolt = <3300000>;
-               regulator-max-microvolt = <3300000>;
-       };
-
-       l10 {
-               regulator-min-microvolt = <2800000>;
-               regulator-max-microvolt = <2800000>;
-       };
-
-       l11 {
-               regulator-min-microvolt = <2950000>;
-               regulator-max-microvolt = <2950000>;
-               regulator-allow-set-load;
-               regulator-system-load = <200000>;
-       };
-
-       l12 {
-               regulator-min-microvolt = <1800000>;
-               regulator-max-microvolt = <2950000>;
-       };
-
-       l13 {
-               regulator-min-microvolt = <3075000>;
-               regulator-max-microvolt = <3075000>;
-       };
-
-       l14 {
-               regulator-min-microvolt = <1800000>;
-               regulator-max-microvolt = <3300000>;
-       };
-
-       l15 {
-               regulator-min-microvolt = <1800000>;
-               regulator-max-microvolt = <3300000>;
-       };
-
-       l16 {
-               regulator-min-microvolt = <1800000>;
-               regulator-max-microvolt = <3300000>;
-       };
-
-       l17 {
-               regulator-min-microvolt = <3000000>;
-               regulator-max-microvolt = <3000000>;
-       };
-
-       l18 {
-               regulator-min-microvolt = <2700000>;
-               regulator-max-microvolt = <2700000>;
-       };
-};
-
 &msmgpio {
        gpio_hall_sensor_default: gpio-hall-sensor-default-state {
                pins = "gpio52";

diff --git a/arch/arm64/boot/dts/qcom/msm8916-samsung-serranove.dts b/arch/arm64/boot/dts/qcom/msm8916-samsung-serranove.dts
index fa5b330aaeaee7699843bc680bc92f9234cdb40e..fc4c61c4e1e6c1ee78d92c8c0c4fe3a2c3ec6d1a 100644 (file)
--- a/arch/arm64/boot/dts/qcom/msm8916-samsung-serranove.dts
+++ b/arch/arm64/boot/dts/qcom/msm8916-samsung-serranove.dts
@@ -320,109 +320,6 @@
        compatible = "qcom,wcn3660b";
 };
 
-&smd_rpm_regulators {
-       vdd_l1_l2_l3-supply = <&pm8916_s3>;
-       vdd_l4_l5_l6-supply = <&pm8916_s4>;
-       vdd_l7-supply = <&pm8916_s4>;
-
-       s3 {
-               regulator-min-microvolt = <1250000>;
-               regulator-max-microvolt = <1350000>;
-       };
-
-       s4 {
-               regulator-min-microvolt = <1850000>;
-               regulator-max-microvolt = <2150000>;
-       };
-
-       l1 {
-               regulator-min-microvolt = <1225000>;
-               regulator-max-microvolt = <1225000>;
-       };
-
-       l2 {
-               regulator-min-microvolt = <1200000>;
-               regulator-max-microvolt = <1200000>;
-       };
-
-       l4 {
-               regulator-min-microvolt = <2050000>;
-               regulator-max-microvolt = <2050000>;
-       };
-
-       l5 {
-               regulator-min-microvolt = <1800000>;
-               regulator-max-microvolt = <1800000>;
-       };
-
-       l6 {
-               regulator-min-microvolt = <1800000>;
-               regulator-max-microvolt = <1800000>;
-       };
-
-       l7 {
-               regulator-min-microvolt = <1800000>;
-               regulator-max-microvolt = <1800000>;
-       };
-
-       l8 {
-               regulator-min-microvolt = <2900000>;
-               regulator-max-microvolt = <2900000>;
-       };
-
-       l9 {
-               regulator-min-microvolt = <3300000>;
-               regulator-max-microvolt = <3300000>;
-       };
-
-       l10 {
-               regulator-min-microvolt = <2800000>;
-               regulator-max-microvolt = <2800000>;
-       };
-
-       l11 {
-               regulator-min-microvolt = <2950000>;
-               regulator-max-microvolt = <2950000>;
-               regulator-allow-set-load;
-               regulator-system-load = <200000>;
-       };
-
-       l12 {
-               regulator-min-microvolt = <1800000>;
-               regulator-max-microvolt = <2950000>;
-       };
-
-       l13 {
-               regulator-min-microvolt = <3075000>;
-               regulator-max-microvolt = <3075000>;
-       };
-
-       l14 {
-               regulator-min-microvolt = <1800000>;
-               regulator-max-microvolt = <3300000>;
-       };
-
-       l15 {
-               regulator-min-microvolt = <1800000>;
-               regulator-max-microvolt = <3300000>;
-       };
-
-       l16 {
-               regulator-min-microvolt = <1800000>;
-               regulator-max-microvolt = <3300000>;
-       };
-
-       l17 {
-               regulator-min-microvolt = <2850000>;
-               regulator-max-microvolt = <2850000>;
-       };
-
-       l18 {
-               regulator-min-microvolt = <2700000>;
-               regulator-max-microvolt = <2700000>;
-       };
-};
-
 &msmgpio {
        fg_alert_default: fg-alert-default-state {
                pins = "gpio121";

diff --git a/arch/arm64/boot/dts/qcom/msm8916-ufi.dtsi b/arch/arm64/boot/dts/qcom/msm8916-ufi.dtsi
index 259c4660bb0fc21b86a06ea8abf2f90b496d0af3..6a92190395720e3840be8fa5bec9e2c17b13e5db 100644 (file)
--- a/arch/arm64/boot/dts/qcom/msm8916-ufi.dtsi
+++ b/arch/arm64/boot/dts/qcom/msm8916-ufi.dtsi
@@ -126,109 +126,6 @@
        compatible = "qcom,wcn3620";
 };
 
-&smd_rpm_regulators {
-       vdd_l1_l2_l3-supply = <&pm8916_s3>;
-       vdd_l4_l5_l6-supply = <&pm8916_s4>;
-       vdd_l7-supply = <&pm8916_s4>;
-
-       s3 {
-               regulator-min-microvolt = <1250000>;
-               regulator-max-microvolt = <1350000>;
-       };
-
-       s4 {
-               regulator-min-microvolt = <1850000>;
-               regulator-max-microvolt = <2150000>;
-       };
-
-       l1 {
-               regulator-min-microvolt = <1225000>;
-               regulator-max-microvolt = <1225000>;
-       };
-
-       l2 {
-               regulator-min-microvolt = <1200000>;
-               regulator-max-microvolt = <1200000>;
-       };
-
-       l4 {
-               regulator-min-microvolt = <2050000>;
-               regulator-max-microvolt = <2050000>;
-       };
-
-       l5 {
-               regulator-min-microvolt = <1800000>;
-               regulator-max-microvolt = <1800000>;
-       };
-
-       l6 {
-               regulator-min-microvolt = <1800000>;
-               regulator-max-microvolt = <1800000>;
-       };
-
-       l7 {
-               regulator-min-microvolt = <1800000>;
-               regulator-max-microvolt = <1800000>;
-       };
-
-       l8 {
-               regulator-min-microvolt = <2900000>;
-               regulator-max-microvolt = <2900000>;
-       };
-
-       l9 {
-               regulator-min-microvolt = <3300000>;
-               regulator-max-microvolt = <3300000>;
-       };
-
-       l10 {
-               regulator-min-microvolt = <2800000>;
-               regulator-max-microvolt = <2800000>;
-       };
-
-       l11 {
-               regulator-min-microvolt = <2950000>;
-               regulator-max-microvolt = <2950000>;
-               regulator-system-load = <200000>;
-               regulator-allow-set-load;
-       };
-
-       l12 {
-               regulator-min-microvolt = <1800000>;
-               regulator-max-microvolt = <2950000>;
-       };
-
-       l13 {
-               regulator-min-microvolt = <3075000>;
-               regulator-max-microvolt = <3075000>;
-       };
-
-       l14 {
-               regulator-min-microvolt = <1800000>;
-               regulator-max-microvolt = <3300000>;
-       };
-
-       l15 {
-               regulator-min-microvolt = <1800000>;
-               regulator-max-microvolt = <3300000>;
-       };
-
-       l16 {
-               regulator-min-microvolt = <1800000>;
-               regulator-max-microvolt = <3300000>;
-       };
-
-       l17 {
-               regulator-min-microvolt = <2850000>;
-               regulator-max-microvolt = <2850000>;
-       };
-
-       l18 {
-               regulator-min-microvolt = <2700000>;
-               regulator-max-microvolt = <2700000>;
-       };
-};
-
 &msmgpio {
        /* pins are board-specific */
        button_default: button-default-state {

diff --git a/arch/arm64/boot/dts/qcom/msm8916-wingtech-wt88047.dts b/arch/arm64/boot/dts/qcom/msm8916-wingtech-wt88047.dts
index 78020a0db4e4889826723405e81bdb5b73c28cb4..323590598113b4bf59b578476cc927c4720ac66a 100644 (file)
--- a/arch/arm64/boot/dts/qcom/msm8916-wingtech-wt88047.dts
+++ b/arch/arm64/boot/dts/qcom/msm8916-wingtech-wt88047.dts
@@ -149,6 +149,22 @@
        linux,code = <KEY_VOLUMEDOWN>;
 };
 
+&pm8916_rpm_regulators {
+       pm8916_l16: l16 {
+               /*
+                * L16 is only used for AW2013 which is fine with 2.5-3.3V.
+                * Use the recommended typical voltage of 2.8V as minimum.
+                */
+               regulator-min-microvolt = <2800000>;
+               regulator-max-microvolt = <3300000>;
+       };
+
+       pm8916_l17: l17 {
+               regulator-min-microvolt = <2850000>;
+               regulator-max-microvolt = <2850000>;
+       };
+};
+
 &pm8916_vib {
        status = "okay";
 };
@@ -188,109 +204,6 @@
        compatible = "qcom,wcn3620";
 };
 
-&smd_rpm_regulators {
-       vdd_l1_l2_l3-supply = <&pm8916_s3>;
-       vdd_l4_l5_l6-supply = <&pm8916_s4>;
-       vdd_l7-supply = <&pm8916_s4>;
-
-       s3 {
-               regulator-min-microvolt = <1250000>;
-               regulator-max-microvolt = <1350000>;
-       };
-
-       s4 {
-               regulator-min-microvolt = <1850000>;
-               regulator-max-microvolt = <2150000>;
-       };
-
-       l1 {
-               regulator-min-microvolt = <1225000>;
-               regulator-max-microvolt = <1225000>;
-       };
-
-       l2 {
-               regulator-min-microvolt = <1200000>;
-               regulator-max-microvolt = <1200000>;
-       };
-
-       l4 {
-               regulator-min-microvolt = <2050000>;
-               regulator-max-microvolt = <2050000>;
-       };
-
-       l5 {
-               regulator-min-microvolt = <1800000>;
-               regulator-max-microvolt = <1800000>;
-       };
-
-       l6 {
-               regulator-min-microvolt = <1800000>;
-               regulator-max-microvolt = <1800000>;
-       };
-
-       l7 {
-               regulator-min-microvolt = <1800000>;
-               regulator-max-microvolt = <1800000>;
-       };
-
-       l8 {
-               regulator-min-microvolt = <2900000>;
-               regulator-max-microvolt = <2900000>;
-       };
-
-       l9 {
-               regulator-min-microvolt = <3300000>;
-               regulator-max-microvolt = <3300000>;
-       };
-
-       l10 {
-               regulator-min-microvolt = <2800000>;
-               regulator-max-microvolt = <2800000>;
-       };
-
-       l11 {
-               regulator-min-microvolt = <2950000>;
-               regulator-max-microvolt = <2950000>;
-               regulator-allow-set-load;
-               regulator-system-load = <200000>;
-       };
-
-       l12 {
-               regulator-min-microvolt = <1800000>;
-               regulator-max-microvolt = <2950000>;
-       };
-
-       l13 {
-               regulator-min-microvolt = <3075000>;
-               regulator-max-microvolt = <3075000>;
-       };
-
-       l14 {
-               regulator-min-microvolt = <1800000>;
-               regulator-max-microvolt = <3300000>;
-       };
-
-       l15 {
-               regulator-min-microvolt = <1800000>;
-               regulator-max-microvolt = <3300000>;
-       };
-
-       l16 {
-               regulator-min-microvolt = <2800000>;
-               regulator-max-microvolt = <3300000>;
-       };
-
-       l17 {
-               regulator-min-microvolt = <2850000>;
-               regulator-max-microvolt = <2850000>;
-       };
-
-       l18 {
-               regulator-min-microvolt = <2700000>;
-               regulator-max-microvolt = <2700000>;
-       };
-};
-
 &msmgpio {
        camera_flash_default: camera-flash-default-state {
                pins = "gpio31", "gpio32";