#define ATH8035_PHY_ID 0x004dd072
#define AT8030_PHY_ID_MASK 0xffffffef
-#define QCA8081_PHY_ID 0x004dd101
-
#define QCA9561_PHY_ID 0x004dd042
#define AT803X_PAGE_FIBER 0
/* disable hibernation mode */
#define AT803X_DISABLE_HIBERNATION_MODE BIT(2)
-/* ADC threshold */
-#define QCA808X_PHY_DEBUG_ADC_THRESHOLD 0x2c80
-#define QCA808X_ADC_THRESHOLD_MASK GENMASK(7, 0)
-#define QCA808X_ADC_THRESHOLD_80MV 0
-#define QCA808X_ADC_THRESHOLD_100MV 0xf0
-#define QCA808X_ADC_THRESHOLD_200MV 0x0f
-#define QCA808X_ADC_THRESHOLD_300MV 0xff
-
-/* CLD control */
-#define QCA808X_PHY_MMD3_ADDR_CLD_CTRL7 0x8007
-#define QCA808X_8023AZ_AFE_CTRL_MASK GENMASK(8, 4)
-#define QCA808X_8023AZ_AFE_EN 0x90
-
-/* AZ control */
-#define QCA808X_PHY_MMD3_AZ_TRAINING_CTRL 0x8008
-#define QCA808X_MMD3_AZ_TRAINING_VAL 0x1c32
-
-#define QCA808X_PHY_MMD1_MSE_THRESHOLD_20DB 0x8014
-#define QCA808X_MSE_THRESHOLD_20DB_VALUE 0x529
-
-#define QCA808X_PHY_MMD1_MSE_THRESHOLD_17DB 0x800E
-#define QCA808X_MSE_THRESHOLD_17DB_VALUE 0x341
-
-#define QCA808X_PHY_MMD1_MSE_THRESHOLD_27DB 0x801E
-#define QCA808X_MSE_THRESHOLD_27DB_VALUE 0x419
-
-#define QCA808X_PHY_MMD1_MSE_THRESHOLD_28DB 0x8020
-#define QCA808X_MSE_THRESHOLD_28DB_VALUE 0x341
-
-#define QCA808X_PHY_MMD7_TOP_OPTION1 0x901c
-#define QCA808X_TOP_OPTION1_DATA 0x0
-
-#define QCA808X_PHY_MMD3_DEBUG_1 0xa100
-#define QCA808X_MMD3_DEBUG_1_VALUE 0x9203
-#define QCA808X_PHY_MMD3_DEBUG_2 0xa101
-#define QCA808X_MMD3_DEBUG_2_VALUE 0x48ad
-#define QCA808X_PHY_MMD3_DEBUG_3 0xa103
-#define QCA808X_MMD3_DEBUG_3_VALUE 0x1698
-#define QCA808X_PHY_MMD3_DEBUG_4 0xa105
-#define QCA808X_MMD3_DEBUG_4_VALUE 0x8001
-#define QCA808X_PHY_MMD3_DEBUG_5 0xa106
-#define QCA808X_MMD3_DEBUG_5_VALUE 0x1111
-#define QCA808X_PHY_MMD3_DEBUG_6 0xa011
-#define QCA808X_MMD3_DEBUG_6_VALUE 0x5f85
-
-/* master/slave seed config */
-#define QCA808X_PHY_DEBUG_LOCAL_SEED 9
-#define QCA808X_MASTER_SLAVE_SEED_ENABLE BIT(1)
-#define QCA808X_MASTER_SLAVE_SEED_CFG GENMASK(12, 2)
-#define QCA808X_MASTER_SLAVE_SEED_RANGE 0x32
-
-/* Hibernation yields lower power consumpiton in contrast with normal operation mode.
- * when the copper cable is unplugged, the PHY enters into hibernation mode in about 10s.
- */
-#define QCA808X_DBG_AN_TEST 0xb
-#define QCA808X_HIBERNATION_EN BIT(15)
-
-#define QCA808X_CDT_ENABLE_TEST BIT(15)
-#define QCA808X_CDT_INTER_CHECK_DIS BIT(13)
-#define QCA808X_CDT_STATUS BIT(11)
-#define QCA808X_CDT_LENGTH_UNIT BIT(10)
-
-#define QCA808X_MMD3_CDT_STATUS 0x8064
-#define QCA808X_MMD3_CDT_DIAG_PAIR_A 0x8065
-#define QCA808X_MMD3_CDT_DIAG_PAIR_B 0x8066
-#define QCA808X_MMD3_CDT_DIAG_PAIR_C 0x8067
-#define QCA808X_MMD3_CDT_DIAG_PAIR_D 0x8068
-#define QCA808X_CDT_DIAG_LENGTH_SAME_SHORT GENMASK(15, 8)
-#define QCA808X_CDT_DIAG_LENGTH_CROSS_SHORT GENMASK(7, 0)
-
-#define QCA808X_CDT_CODE_PAIR_A GENMASK(15, 12)
-#define QCA808X_CDT_CODE_PAIR_B GENMASK(11, 8)
-#define QCA808X_CDT_CODE_PAIR_C GENMASK(7, 4)
-#define QCA808X_CDT_CODE_PAIR_D GENMASK(3, 0)
-
-#define QCA808X_CDT_STATUS_STAT_TYPE GENMASK(1, 0)
-#define QCA808X_CDT_STATUS_STAT_FAIL FIELD_PREP_CONST(QCA808X_CDT_STATUS_STAT_TYPE, 0)
-#define QCA808X_CDT_STATUS_STAT_NORMAL FIELD_PREP_CONST(QCA808X_CDT_STATUS_STAT_TYPE, 1)
-#define QCA808X_CDT_STATUS_STAT_SAME_OPEN FIELD_PREP_CONST(QCA808X_CDT_STATUS_STAT_TYPE, 2)
-#define QCA808X_CDT_STATUS_STAT_SAME_SHORT FIELD_PREP_CONST(QCA808X_CDT_STATUS_STAT_TYPE, 3)
-
-#define QCA808X_CDT_STATUS_STAT_MDI GENMASK(3, 2)
-#define QCA808X_CDT_STATUS_STAT_MDI1 FIELD_PREP_CONST(QCA808X_CDT_STATUS_STAT_MDI, 1)
-#define QCA808X_CDT_STATUS_STAT_MDI2 FIELD_PREP_CONST(QCA808X_CDT_STATUS_STAT_MDI, 2)
-#define QCA808X_CDT_STATUS_STAT_MDI3 FIELD_PREP_CONST(QCA808X_CDT_STATUS_STAT_MDI, 3)
-
-/* NORMAL are MDI with type set to 0 */
-#define QCA808X_CDT_STATUS_STAT_CROSS_SHORT_WITH_MDI1_SAME_NORMAL QCA808X_CDT_STATUS_STAT_MDI1
-#define QCA808X_CDT_STATUS_STAT_CROSS_SHORT_WITH_MDI1_SAME_OPEN (QCA808X_CDT_STATUS_STAT_SAME_OPEN |\
- QCA808X_CDT_STATUS_STAT_MDI1)
-#define QCA808X_CDT_STATUS_STAT_CROSS_SHORT_WITH_MDI1_SAME_SHORT (QCA808X_CDT_STATUS_STAT_SAME_SHORT |\
- QCA808X_CDT_STATUS_STAT_MDI1)
-#define QCA808X_CDT_STATUS_STAT_CROSS_SHORT_WITH_MDI2_SAME_NORMAL QCA808X_CDT_STATUS_STAT_MDI2
-#define QCA808X_CDT_STATUS_STAT_CROSS_SHORT_WITH_MDI2_SAME_OPEN (QCA808X_CDT_STATUS_STAT_SAME_OPEN |\
- QCA808X_CDT_STATUS_STAT_MDI2)
-#define QCA808X_CDT_STATUS_STAT_CROSS_SHORT_WITH_MDI2_SAME_SHORT (QCA808X_CDT_STATUS_STAT_SAME_SHORT |\
- QCA808X_CDT_STATUS_STAT_MDI2)
-#define QCA808X_CDT_STATUS_STAT_CROSS_SHORT_WITH_MDI3_SAME_NORMAL QCA808X_CDT_STATUS_STAT_MDI3
-#define QCA808X_CDT_STATUS_STAT_CROSS_SHORT_WITH_MDI3_SAME_OPEN (QCA808X_CDT_STATUS_STAT_SAME_OPEN |\
- QCA808X_CDT_STATUS_STAT_MDI3)
-#define QCA808X_CDT_STATUS_STAT_CROSS_SHORT_WITH_MDI3_SAME_SHORT (QCA808X_CDT_STATUS_STAT_SAME_SHORT |\
- QCA808X_CDT_STATUS_STAT_MDI3)
-
-/* Added for reference of existence but should be handled by wait_for_completion already */
-#define QCA808X_CDT_STATUS_STAT_BUSY (BIT(1) | BIT(3))
-
-#define QCA808X_MMD7_LED_GLOBAL 0x8073
-#define QCA808X_LED_BLINK_1 GENMASK(11, 6)
-#define QCA808X_LED_BLINK_2 GENMASK(5, 0)
-/* Values are the same for both BLINK_1 and BLINK_2 */
-#define QCA808X_LED_BLINK_FREQ_MASK GENMASK(5, 3)
-#define QCA808X_LED_BLINK_FREQ_2HZ FIELD_PREP(QCA808X_LED_BLINK_FREQ_MASK, 0x0)
-#define QCA808X_LED_BLINK_FREQ_4HZ FIELD_PREP(QCA808X_LED_BLINK_FREQ_MASK, 0x1)
-#define QCA808X_LED_BLINK_FREQ_8HZ FIELD_PREP(QCA808X_LED_BLINK_FREQ_MASK, 0x2)
-#define QCA808X_LED_BLINK_FREQ_16HZ FIELD_PREP(QCA808X_LED_BLINK_FREQ_MASK, 0x3)
-#define QCA808X_LED_BLINK_FREQ_32HZ FIELD_PREP(QCA808X_LED_BLINK_FREQ_MASK, 0x4)
-#define QCA808X_LED_BLINK_FREQ_64HZ FIELD_PREP(QCA808X_LED_BLINK_FREQ_MASK, 0x5)
-#define QCA808X_LED_BLINK_FREQ_128HZ FIELD_PREP(QCA808X_LED_BLINK_FREQ_MASK, 0x6)
-#define QCA808X_LED_BLINK_FREQ_256HZ FIELD_PREP(QCA808X_LED_BLINK_FREQ_MASK, 0x7)
-#define QCA808X_LED_BLINK_DUTY_MASK GENMASK(2, 0)
-#define QCA808X_LED_BLINK_DUTY_50_50 FIELD_PREP(QCA808X_LED_BLINK_DUTY_MASK, 0x0)
-#define QCA808X_LED_BLINK_DUTY_75_25 FIELD_PREP(QCA808X_LED_BLINK_DUTY_MASK, 0x1)
-#define QCA808X_LED_BLINK_DUTY_25_75 FIELD_PREP(QCA808X_LED_BLINK_DUTY_MASK, 0x2)
-#define QCA808X_LED_BLINK_DUTY_33_67 FIELD_PREP(QCA808X_LED_BLINK_DUTY_MASK, 0x3)
-#define QCA808X_LED_BLINK_DUTY_67_33 FIELD_PREP(QCA808X_LED_BLINK_DUTY_MASK, 0x4)
-#define QCA808X_LED_BLINK_DUTY_17_83 FIELD_PREP(QCA808X_LED_BLINK_DUTY_MASK, 0x5)
-#define QCA808X_LED_BLINK_DUTY_83_17 FIELD_PREP(QCA808X_LED_BLINK_DUTY_MASK, 0x6)
-#define QCA808X_LED_BLINK_DUTY_8_92 FIELD_PREP(QCA808X_LED_BLINK_DUTY_MASK, 0x7)
-
-#define QCA808X_MMD7_LED2_CTRL 0x8074
-#define QCA808X_MMD7_LED2_FORCE_CTRL 0x8075
-#define QCA808X_MMD7_LED1_CTRL 0x8076
-#define QCA808X_MMD7_LED1_FORCE_CTRL 0x8077
-#define QCA808X_MMD7_LED0_CTRL 0x8078
-#define QCA808X_MMD7_LED_CTRL(x) (0x8078 - ((x) * 2))
-
-/* LED hw control pattern is the same for every LED */
-#define QCA808X_LED_PATTERN_MASK GENMASK(15, 0)
-#define QCA808X_LED_SPEED2500_ON BIT(15)
-#define QCA808X_LED_SPEED2500_BLINK BIT(14)
-/* Follow blink trigger even if duplex or speed condition doesn't match */
-#define QCA808X_LED_BLINK_CHECK_BYPASS BIT(13)
-#define QCA808X_LED_FULL_DUPLEX_ON BIT(12)
-#define QCA808X_LED_HALF_DUPLEX_ON BIT(11)
-#define QCA808X_LED_TX_BLINK BIT(10)
-#define QCA808X_LED_RX_BLINK BIT(9)
-#define QCA808X_LED_TX_ON_10MS BIT(8)
-#define QCA808X_LED_RX_ON_10MS BIT(7)
-#define QCA808X_LED_SPEED1000_ON BIT(6)
-#define QCA808X_LED_SPEED100_ON BIT(5)
-#define QCA808X_LED_SPEED10_ON BIT(4)
-#define QCA808X_LED_COLLISION_BLINK BIT(3)
-#define QCA808X_LED_SPEED1000_BLINK BIT(2)
-#define QCA808X_LED_SPEED100_BLINK BIT(1)
-#define QCA808X_LED_SPEED10_BLINK BIT(0)
-
-#define QCA808X_MMD7_LED0_FORCE_CTRL 0x8079
-#define QCA808X_MMD7_LED_FORCE_CTRL(x) (0x8079 - ((x) * 2))
-
-/* LED force ctrl is the same for every LED
- * No documentation exist for this, not even internal one
- * with NDA as QCOM gives only info about configuring
- * hw control pattern rules and doesn't indicate any way
- * to force the LED to specific mode.
- * These define comes from reverse and testing and maybe
- * lack of some info or some info are not entirely correct.
- * For the basic LED control and hw control these finding
- * are enough to support LED control in all the required APIs.
- *
- * On doing some comparison with implementation with qca807x,
- * it was found that it's 1:1 equal to it and confirms all the
- * reverse done. It was also found further specification with the
- * force mode and the blink modes.
- */
-#define QCA808X_LED_FORCE_EN BIT(15)
-#define QCA808X_LED_FORCE_MODE_MASK GENMASK(14, 13)
-#define QCA808X_LED_FORCE_BLINK_1 FIELD_PREP(QCA808X_LED_FORCE_MODE_MASK, 0x3)
-#define QCA808X_LED_FORCE_BLINK_2 FIELD_PREP(QCA808X_LED_FORCE_MODE_MASK, 0x2)
-#define QCA808X_LED_FORCE_ON FIELD_PREP(QCA808X_LED_FORCE_MODE_MASK, 0x1)
-#define QCA808X_LED_FORCE_OFF FIELD_PREP(QCA808X_LED_FORCE_MODE_MASK, 0x0)
-
-#define QCA808X_MMD7_LED_POLARITY_CTRL 0x901a
-/* QSDK sets by default 0x46 to this reg that sets BIT 6 for
- * LED to active high. It's not clear what BIT 3 and BIT 4 does.
- */
-#define QCA808X_LED_ACTIVE_HIGH BIT(6)
-
-/* QCA808X 1G chip type */
-#define QCA808X_PHY_MMD7_CHIP_TYPE 0x901d
-#define QCA808X_PHY_CHIP_TYPE_1G BIT(0)
-
-#define QCA8081_PHY_SERDES_MMD1_FIFO_CTRL 0x9072
-#define QCA8081_PHY_FIFO_RSTN BIT(11)
-
-MODULE_DESCRIPTION("Qualcomm Atheros AR803x and QCA808X PHY driver");
+MODULE_DESCRIPTION("Qualcomm Atheros AR803x PHY driver");
MODULE_AUTHOR("Matus Ujhelyi");
MODULE_LICENSE("GPL");
bool is_1000basex;
struct regulator_dev *vddio_rdev;
struct regulator_dev *vddh_rdev;
- int led_polarity_mode;
};
struct at803x_context {
if (!priv)
return -ENOMEM;
- /* Init LED polarity mode to -1 */
- priv->led_polarity_mode = -1;
-
phydev->priv = priv;
ret = at803x_parse_dt(phydev);
return at8035_parse_dt(phydev);
}
-static int qca808x_phy_fast_retrain_config(struct phy_device *phydev)
-{
- int ret;
-
- /* Enable fast retrain */
- ret = genphy_c45_fast_retrain(phydev, true);
- if (ret)
- return ret;
-
- phy_write_mmd(phydev, MDIO_MMD_AN, QCA808X_PHY_MMD7_TOP_OPTION1,
- QCA808X_TOP_OPTION1_DATA);
- phy_write_mmd(phydev, MDIO_MMD_PMAPMD, QCA808X_PHY_MMD1_MSE_THRESHOLD_20DB,
- QCA808X_MSE_THRESHOLD_20DB_VALUE);
- phy_write_mmd(phydev, MDIO_MMD_PMAPMD, QCA808X_PHY_MMD1_MSE_THRESHOLD_17DB,
- QCA808X_MSE_THRESHOLD_17DB_VALUE);
- phy_write_mmd(phydev, MDIO_MMD_PMAPMD, QCA808X_PHY_MMD1_MSE_THRESHOLD_27DB,
- QCA808X_MSE_THRESHOLD_27DB_VALUE);
- phy_write_mmd(phydev, MDIO_MMD_PMAPMD, QCA808X_PHY_MMD1_MSE_THRESHOLD_28DB,
- QCA808X_MSE_THRESHOLD_28DB_VALUE);
- phy_write_mmd(phydev, MDIO_MMD_PCS, QCA808X_PHY_MMD3_DEBUG_1,
- QCA808X_MMD3_DEBUG_1_VALUE);
- phy_write_mmd(phydev, MDIO_MMD_PCS, QCA808X_PHY_MMD3_DEBUG_4,
- QCA808X_MMD3_DEBUG_4_VALUE);
- phy_write_mmd(phydev, MDIO_MMD_PCS, QCA808X_PHY_MMD3_DEBUG_5,
- QCA808X_MMD3_DEBUG_5_VALUE);
- phy_write_mmd(phydev, MDIO_MMD_PCS, QCA808X_PHY_MMD3_DEBUG_3,
- QCA808X_MMD3_DEBUG_3_VALUE);
- phy_write_mmd(phydev, MDIO_MMD_PCS, QCA808X_PHY_MMD3_DEBUG_6,
- QCA808X_MMD3_DEBUG_6_VALUE);
- phy_write_mmd(phydev, MDIO_MMD_PCS, QCA808X_PHY_MMD3_DEBUG_2,
- QCA808X_MMD3_DEBUG_2_VALUE);
-
- return 0;
-}
-
-static int qca808x_phy_ms_seed_enable(struct phy_device *phydev, bool enable)
-{
- u16 seed_value;
-
- if (!enable)
- return at803x_debug_reg_mask(phydev, QCA808X_PHY_DEBUG_LOCAL_SEED,
- QCA808X_MASTER_SLAVE_SEED_ENABLE, 0);
-
- seed_value = get_random_u32_below(QCA808X_MASTER_SLAVE_SEED_RANGE);
- return at803x_debug_reg_mask(phydev, QCA808X_PHY_DEBUG_LOCAL_SEED,
- QCA808X_MASTER_SLAVE_SEED_CFG | QCA808X_MASTER_SLAVE_SEED_ENABLE,
- FIELD_PREP(QCA808X_MASTER_SLAVE_SEED_CFG, seed_value) |
- QCA808X_MASTER_SLAVE_SEED_ENABLE);
-}
-
-static bool qca808x_is_prefer_master(struct phy_device *phydev)
-{
- return (phydev->master_slave_get == MASTER_SLAVE_CFG_MASTER_FORCE) ||
- (phydev->master_slave_get == MASTER_SLAVE_CFG_MASTER_PREFERRED);
-}
-
-static bool qca808x_has_fast_retrain_or_slave_seed(struct phy_device *phydev)
-{
- return linkmode_test_bit(ETHTOOL_LINK_MODE_2500baseT_Full_BIT, phydev->supported);
-}
-
-static int qca808x_config_init(struct phy_device *phydev)
-{
- int ret;
-
- /* Active adc&vga on 802.3az for the link 1000M and 100M */
- ret = phy_modify_mmd(phydev, MDIO_MMD_PCS, QCA808X_PHY_MMD3_ADDR_CLD_CTRL7,
- QCA808X_8023AZ_AFE_CTRL_MASK, QCA808X_8023AZ_AFE_EN);
- if (ret)
- return ret;
-
- /* Adjust the threshold on 802.3az for the link 1000M */
- ret = phy_write_mmd(phydev, MDIO_MMD_PCS,
- QCA808X_PHY_MMD3_AZ_TRAINING_CTRL,
- QCA808X_MMD3_AZ_TRAINING_VAL);
- if (ret)
- return ret;
-
- if (qca808x_has_fast_retrain_or_slave_seed(phydev)) {
- /* Config the fast retrain for the link 2500M */
- ret = qca808x_phy_fast_retrain_config(phydev);
- if (ret)
- return ret;
-
- ret = genphy_read_master_slave(phydev);
- if (ret < 0)
- return ret;
-
- if (!qca808x_is_prefer_master(phydev)) {
- /* Enable seed and configure lower ramdom seed to make phy
- * linked as slave mode.
- */
- ret = qca808x_phy_ms_seed_enable(phydev, true);
- if (ret)
- return ret;
- }
- }
-
- /* Configure adc threshold as 100mv for the link 10M */
- return at803x_debug_reg_mask(phydev, QCA808X_PHY_DEBUG_ADC_THRESHOLD,
- QCA808X_ADC_THRESHOLD_MASK,
- QCA808X_ADC_THRESHOLD_100MV);
-}
-
-static int qca808x_read_status(struct phy_device *phydev)
-{
- struct at803x_ss_mask ss_mask = { 0 };
- int ret;
-
- ret = phy_read_mmd(phydev, MDIO_MMD_AN, MDIO_AN_10GBT_STAT);
- if (ret < 0)
- return ret;
-
- linkmode_mod_bit(ETHTOOL_LINK_MODE_2500baseT_Full_BIT, phydev->lp_advertising,
- ret & MDIO_AN_10GBT_STAT_LP2_5G);
-
- ret = genphy_read_status(phydev);
- if (ret)
- return ret;
-
- /* qca8081 takes the different bits for speed value from at803x */
- ss_mask.speed_mask = QCA808X_SS_SPEED_MASK;
- ss_mask.speed_shift = __bf_shf(QCA808X_SS_SPEED_MASK);
- ret = at803x_read_specific_status(phydev, ss_mask);
- if (ret < 0)
- return ret;
-
- if (phydev->link) {
- if (phydev->speed == SPEED_2500)
- phydev->interface = PHY_INTERFACE_MODE_2500BASEX;
- else
- phydev->interface = PHY_INTERFACE_MODE_SGMII;
- } else {
- /* generate seed as a lower random value to make PHY linked as SLAVE easily,
- * except for master/slave configuration fault detected or the master mode
- * preferred.
- *
- * the reason for not putting this code into the function link_change_notify is
- * the corner case where the link partner is also the qca8081 PHY and the seed
- * value is configured as the same value, the link can't be up and no link change
- * occurs.
- */
- if (qca808x_has_fast_retrain_or_slave_seed(phydev)) {
- if (phydev->master_slave_state == MASTER_SLAVE_STATE_ERR ||
- qca808x_is_prefer_master(phydev)) {
- qca808x_phy_ms_seed_enable(phydev, false);
- } else {
- qca808x_phy_ms_seed_enable(phydev, true);
- }
- }
- }
-
- return 0;
-}
-
-static int qca808x_soft_reset(struct phy_device *phydev)
-{
- int ret;
-
- ret = genphy_soft_reset(phydev);
- if (ret < 0)
- return ret;
-
- if (qca808x_has_fast_retrain_or_slave_seed(phydev))
- ret = qca808x_phy_ms_seed_enable(phydev, true);
-
- return ret;
-}
-
-static bool qca808x_cdt_fault_length_valid(int cdt_code)
-{
- switch (cdt_code) {
- case QCA808X_CDT_STATUS_STAT_SAME_SHORT:
- case QCA808X_CDT_STATUS_STAT_SAME_OPEN:
- case QCA808X_CDT_STATUS_STAT_CROSS_SHORT_WITH_MDI1_SAME_NORMAL:
- case QCA808X_CDT_STATUS_STAT_CROSS_SHORT_WITH_MDI1_SAME_OPEN:
- case QCA808X_CDT_STATUS_STAT_CROSS_SHORT_WITH_MDI1_SAME_SHORT:
- case QCA808X_CDT_STATUS_STAT_CROSS_SHORT_WITH_MDI2_SAME_NORMAL:
- case QCA808X_CDT_STATUS_STAT_CROSS_SHORT_WITH_MDI2_SAME_OPEN:
- case QCA808X_CDT_STATUS_STAT_CROSS_SHORT_WITH_MDI2_SAME_SHORT:
- case QCA808X_CDT_STATUS_STAT_CROSS_SHORT_WITH_MDI3_SAME_NORMAL:
- case QCA808X_CDT_STATUS_STAT_CROSS_SHORT_WITH_MDI3_SAME_OPEN:
- case QCA808X_CDT_STATUS_STAT_CROSS_SHORT_WITH_MDI3_SAME_SHORT:
- return true;
- default:
- return false;
- }
-}
-
-static int qca808x_cable_test_result_trans(int cdt_code)
-{
- switch (cdt_code) {
- case QCA808X_CDT_STATUS_STAT_NORMAL:
- return ETHTOOL_A_CABLE_RESULT_CODE_OK;
- case QCA808X_CDT_STATUS_STAT_SAME_SHORT:
- return ETHTOOL_A_CABLE_RESULT_CODE_SAME_SHORT;
- case QCA808X_CDT_STATUS_STAT_SAME_OPEN:
- return ETHTOOL_A_CABLE_RESULT_CODE_OPEN;
- case QCA808X_CDT_STATUS_STAT_CROSS_SHORT_WITH_MDI1_SAME_NORMAL:
- case QCA808X_CDT_STATUS_STAT_CROSS_SHORT_WITH_MDI1_SAME_OPEN:
- case QCA808X_CDT_STATUS_STAT_CROSS_SHORT_WITH_MDI1_SAME_SHORT:
- case QCA808X_CDT_STATUS_STAT_CROSS_SHORT_WITH_MDI2_SAME_NORMAL:
- case QCA808X_CDT_STATUS_STAT_CROSS_SHORT_WITH_MDI2_SAME_OPEN:
- case QCA808X_CDT_STATUS_STAT_CROSS_SHORT_WITH_MDI2_SAME_SHORT:
- case QCA808X_CDT_STATUS_STAT_CROSS_SHORT_WITH_MDI3_SAME_NORMAL:
- case QCA808X_CDT_STATUS_STAT_CROSS_SHORT_WITH_MDI3_SAME_OPEN:
- case QCA808X_CDT_STATUS_STAT_CROSS_SHORT_WITH_MDI3_SAME_SHORT:
- return ETHTOOL_A_CABLE_RESULT_CODE_CROSS_SHORT;
- case QCA808X_CDT_STATUS_STAT_FAIL:
- default:
- return ETHTOOL_A_CABLE_RESULT_CODE_UNSPEC;
- }
-}
-
-static int qca808x_cdt_fault_length(struct phy_device *phydev, int pair,
- int result)
-{
- int val;
- u32 cdt_length_reg = 0;
-
- switch (pair) {
- case ETHTOOL_A_CABLE_PAIR_A:
- cdt_length_reg = QCA808X_MMD3_CDT_DIAG_PAIR_A;
- break;
- case ETHTOOL_A_CABLE_PAIR_B:
- cdt_length_reg = QCA808X_MMD3_CDT_DIAG_PAIR_B;
- break;
- case ETHTOOL_A_CABLE_PAIR_C:
- cdt_length_reg = QCA808X_MMD3_CDT_DIAG_PAIR_C;
- break;
- case ETHTOOL_A_CABLE_PAIR_D:
- cdt_length_reg = QCA808X_MMD3_CDT_DIAG_PAIR_D;
- break;
- default:
- return -EINVAL;
- }
-
- val = phy_read_mmd(phydev, MDIO_MMD_PCS, cdt_length_reg);
- if (val < 0)
- return val;
-
- if (result == ETHTOOL_A_CABLE_RESULT_CODE_SAME_SHORT)
- val = FIELD_GET(QCA808X_CDT_DIAG_LENGTH_SAME_SHORT, val);
- else
- val = FIELD_GET(QCA808X_CDT_DIAG_LENGTH_CROSS_SHORT, val);
-
- return at803x_cdt_fault_length(val);
-}
-
-static int qca808x_cable_test_start(struct phy_device *phydev)
-{
- int ret;
-
- /* perform CDT with the following configs:
- * 1. disable hibernation.
- * 2. force PHY working in MDI mode.
- * 3. for PHY working in 1000BaseT.
- * 4. configure the threshold.
- */
-
- ret = at803x_debug_reg_mask(phydev, QCA808X_DBG_AN_TEST, QCA808X_HIBERNATION_EN, 0);
- if (ret < 0)
- return ret;
-
- ret = at803x_config_mdix(phydev, ETH_TP_MDI);
- if (ret < 0)
- return ret;
-
- /* Force 1000base-T needs to configure PMA/PMD and MII_BMCR */
- phydev->duplex = DUPLEX_FULL;
- phydev->speed = SPEED_1000;
- ret = genphy_c45_pma_setup_forced(phydev);
- if (ret < 0)
- return ret;
-
- ret = genphy_setup_forced(phydev);
- if (ret < 0)
- return ret;
-
- /* configure the thresholds for open, short, pair ok test */
- phy_write_mmd(phydev, MDIO_MMD_PCS, 0x8074, 0xc040);
- phy_write_mmd(phydev, MDIO_MMD_PCS, 0x8076, 0xc040);
- phy_write_mmd(phydev, MDIO_MMD_PCS, 0x8077, 0xa060);
- phy_write_mmd(phydev, MDIO_MMD_PCS, 0x8078, 0xc050);
- phy_write_mmd(phydev, MDIO_MMD_PCS, 0x807a, 0xc060);
- phy_write_mmd(phydev, MDIO_MMD_PCS, 0x807e, 0xb060);
-
- return 0;
-}
-
-static int qca808x_cable_test_get_pair_status(struct phy_device *phydev, u8 pair,
- u16 status)
-{
- int length, result;
- u16 pair_code;
-
- switch (pair) {
- case ETHTOOL_A_CABLE_PAIR_A:
- pair_code = FIELD_GET(QCA808X_CDT_CODE_PAIR_A, status);
- break;
- case ETHTOOL_A_CABLE_PAIR_B:
- pair_code = FIELD_GET(QCA808X_CDT_CODE_PAIR_B, status);
- break;
- case ETHTOOL_A_CABLE_PAIR_C:
- pair_code = FIELD_GET(QCA808X_CDT_CODE_PAIR_C, status);
- break;
- case ETHTOOL_A_CABLE_PAIR_D:
- pair_code = FIELD_GET(QCA808X_CDT_CODE_PAIR_D, status);
- break;
- default:
- return -EINVAL;
- }
-
- result = qca808x_cable_test_result_trans(pair_code);
- ethnl_cable_test_result(phydev, pair, result);
-
- if (qca808x_cdt_fault_length_valid(pair_code)) {
- length = qca808x_cdt_fault_length(phydev, pair, result);
- ethnl_cable_test_fault_length(phydev, pair, length);
- }
-
- return 0;
-}
-
-static int qca808x_cable_test_get_status(struct phy_device *phydev, bool *finished)
-{
- int ret, val;
-
- *finished = false;
-
- val = QCA808X_CDT_ENABLE_TEST |
- QCA808X_CDT_LENGTH_UNIT;
- ret = at803x_cdt_start(phydev, val);
- if (ret)
- return ret;
-
- ret = at803x_cdt_wait_for_completion(phydev, QCA808X_CDT_ENABLE_TEST);
- if (ret)
- return ret;
-
- val = phy_read_mmd(phydev, MDIO_MMD_PCS, QCA808X_MMD3_CDT_STATUS);
- if (val < 0)
- return val;
-
- ret = qca808x_cable_test_get_pair_status(phydev, ETHTOOL_A_CABLE_PAIR_A, val);
- if (ret)
- return ret;
-
- ret = qca808x_cable_test_get_pair_status(phydev, ETHTOOL_A_CABLE_PAIR_B, val);
- if (ret)
- return ret;
-
- ret = qca808x_cable_test_get_pair_status(phydev, ETHTOOL_A_CABLE_PAIR_C, val);
- if (ret)
- return ret;
-
- ret = qca808x_cable_test_get_pair_status(phydev, ETHTOOL_A_CABLE_PAIR_D, val);
- if (ret)
- return ret;
-
- *finished = true;
-
- return 0;
-}
-
-static int qca808x_get_features(struct phy_device *phydev)
-{
- int ret;
-
- ret = genphy_c45_pma_read_abilities(phydev);
- if (ret)
- return ret;
-
- /* The autoneg ability is not existed in bit3 of MMD7.1,
- * but it is supported by qca808x PHY, so we add it here
- * manually.
- */
- linkmode_set_bit(ETHTOOL_LINK_MODE_Autoneg_BIT, phydev->supported);
-
- /* As for the qca8081 1G version chip, the 2500baseT ability is also
- * existed in the bit0 of MMD1.21, we need to remove it manually if
- * it is the qca8081 1G chip according to the bit0 of MMD7.0x901d.
- */
- ret = phy_read_mmd(phydev, MDIO_MMD_AN, QCA808X_PHY_MMD7_CHIP_TYPE);
- if (ret < 0)
- return ret;
-
- if (QCA808X_PHY_CHIP_TYPE_1G & ret)
- linkmode_clear_bit(ETHTOOL_LINK_MODE_2500baseT_Full_BIT, phydev->supported);
-
- return 0;
-}
-
-static int qca808x_config_aneg(struct phy_device *phydev)
-{
- int phy_ctrl = 0;
- int ret;
-
- ret = at803x_prepare_config_aneg(phydev);
- if (ret)
- return ret;
-
- /* The reg MII_BMCR also needs to be configured for force mode, the
- * genphy_config_aneg is also needed.
- */
- if (phydev->autoneg == AUTONEG_DISABLE)
- genphy_c45_pma_setup_forced(phydev);
-
- if (linkmode_test_bit(ETHTOOL_LINK_MODE_2500baseT_Full_BIT, phydev->advertising))
- phy_ctrl = MDIO_AN_10GBT_CTRL_ADV2_5G;
-
- ret = phy_modify_mmd_changed(phydev, MDIO_MMD_AN, MDIO_AN_10GBT_CTRL,
- MDIO_AN_10GBT_CTRL_ADV2_5G, phy_ctrl);
- if (ret < 0)
- return ret;
-
- return __genphy_config_aneg(phydev, ret);
-}
-
-static void qca808x_link_change_notify(struct phy_device *phydev)
-{
- /* Assert interface sgmii fifo on link down, deassert it on link up,
- * the interface device address is always phy address added by 1.
- */
- mdiobus_c45_modify_changed(phydev->mdio.bus, phydev->mdio.addr + 1,
- MDIO_MMD_PMAPMD, QCA8081_PHY_SERDES_MMD1_FIFO_CTRL,
- QCA8081_PHY_FIFO_RSTN,
- phydev->link ? QCA8081_PHY_FIFO_RSTN : 0);
-}
-
-static int qca808x_led_parse_netdev(struct phy_device *phydev, unsigned long rules,
- u16 *offload_trigger)
-{
- /* Parsing specific to netdev trigger */
- if (test_bit(TRIGGER_NETDEV_TX, &rules))
- *offload_trigger |= QCA808X_LED_TX_BLINK;
- if (test_bit(TRIGGER_NETDEV_RX, &rules))
- *offload_trigger |= QCA808X_LED_RX_BLINK;
- if (test_bit(TRIGGER_NETDEV_LINK_10, &rules))
- *offload_trigger |= QCA808X_LED_SPEED10_ON;
- if (test_bit(TRIGGER_NETDEV_LINK_100, &rules))
- *offload_trigger |= QCA808X_LED_SPEED100_ON;
- if (test_bit(TRIGGER_NETDEV_LINK_1000, &rules))
- *offload_trigger |= QCA808X_LED_SPEED1000_ON;
- if (test_bit(TRIGGER_NETDEV_LINK_2500, &rules))
- *offload_trigger |= QCA808X_LED_SPEED2500_ON;
- if (test_bit(TRIGGER_NETDEV_HALF_DUPLEX, &rules))
- *offload_trigger |= QCA808X_LED_HALF_DUPLEX_ON;
- if (test_bit(TRIGGER_NETDEV_FULL_DUPLEX, &rules))
- *offload_trigger |= QCA808X_LED_FULL_DUPLEX_ON;
-
- if (rules && !*offload_trigger)
- return -EOPNOTSUPP;
-
- /* Enable BLINK_CHECK_BYPASS by default to make the LED
- * blink even with duplex or speed mode not enabled.
- */
- *offload_trigger |= QCA808X_LED_BLINK_CHECK_BYPASS;
-
- return 0;
-}
-
-static int qca808x_led_hw_control_enable(struct phy_device *phydev, u8 index)
-{
- u16 reg;
-
- if (index > 2)
- return -EINVAL;
-
- reg = QCA808X_MMD7_LED_FORCE_CTRL(index);
-
- return phy_clear_bits_mmd(phydev, MDIO_MMD_AN, reg,
- QCA808X_LED_FORCE_EN);
-}
-
-static int qca808x_led_hw_is_supported(struct phy_device *phydev, u8 index,
- unsigned long rules)
-{
- u16 offload_trigger = 0;
-
- if (index > 2)
- return -EINVAL;
-
- return qca808x_led_parse_netdev(phydev, rules, &offload_trigger);
-}
-
-static int qca808x_led_hw_control_set(struct phy_device *phydev, u8 index,
- unsigned long rules)
-{
- u16 reg, offload_trigger = 0;
- int ret;
-
- if (index > 2)
- return -EINVAL;
-
- reg = QCA808X_MMD7_LED_CTRL(index);
-
- ret = qca808x_led_parse_netdev(phydev, rules, &offload_trigger);
- if (ret)
- return ret;
-
- ret = qca808x_led_hw_control_enable(phydev, index);
- if (ret)
- return ret;
-
- return phy_modify_mmd(phydev, MDIO_MMD_AN, reg,
- QCA808X_LED_PATTERN_MASK,
- offload_trigger);
-}
-
-static bool qca808x_led_hw_control_status(struct phy_device *phydev, u8 index)
-{
- u16 reg;
- int val;
-
- if (index > 2)
- return false;
-
- reg = QCA808X_MMD7_LED_FORCE_CTRL(index);
-
- val = phy_read_mmd(phydev, MDIO_MMD_AN, reg);
-
- return !(val & QCA808X_LED_FORCE_EN);
-}
-
-static int qca808x_led_hw_control_get(struct phy_device *phydev, u8 index,
- unsigned long *rules)
-{
- u16 reg;
- int val;
-
- if (index > 2)
- return -EINVAL;
-
- /* Check if we have hw control enabled */
- if (qca808x_led_hw_control_status(phydev, index))
- return -EINVAL;
-
- reg = QCA808X_MMD7_LED_CTRL(index);
-
- val = phy_read_mmd(phydev, MDIO_MMD_AN, reg);
- if (val & QCA808X_LED_TX_BLINK)
- set_bit(TRIGGER_NETDEV_TX, rules);
- if (val & QCA808X_LED_RX_BLINK)
- set_bit(TRIGGER_NETDEV_RX, rules);
- if (val & QCA808X_LED_SPEED10_ON)
- set_bit(TRIGGER_NETDEV_LINK_10, rules);
- if (val & QCA808X_LED_SPEED100_ON)
- set_bit(TRIGGER_NETDEV_LINK_100, rules);
- if (val & QCA808X_LED_SPEED1000_ON)
- set_bit(TRIGGER_NETDEV_LINK_1000, rules);
- if (val & QCA808X_LED_SPEED2500_ON)
- set_bit(TRIGGER_NETDEV_LINK_2500, rules);
- if (val & QCA808X_LED_HALF_DUPLEX_ON)
- set_bit(TRIGGER_NETDEV_HALF_DUPLEX, rules);
- if (val & QCA808X_LED_FULL_DUPLEX_ON)
- set_bit(TRIGGER_NETDEV_FULL_DUPLEX, rules);
-
- return 0;
-}
-
-static int qca808x_led_hw_control_reset(struct phy_device *phydev, u8 index)
-{
- u16 reg;
-
- if (index > 2)
- return -EINVAL;
-
- reg = QCA808X_MMD7_LED_CTRL(index);
-
- return phy_clear_bits_mmd(phydev, MDIO_MMD_AN, reg,
- QCA808X_LED_PATTERN_MASK);
-}
-
-static int qca808x_led_brightness_set(struct phy_device *phydev,
- u8 index, enum led_brightness value)
-{
- u16 reg;
- int ret;
-
- if (index > 2)
- return -EINVAL;
-
- if (!value) {
- ret = qca808x_led_hw_control_reset(phydev, index);
- if (ret)
- return ret;
- }
-
- reg = QCA808X_MMD7_LED_FORCE_CTRL(index);
-
- return phy_modify_mmd(phydev, MDIO_MMD_AN, reg,
- QCA808X_LED_FORCE_EN | QCA808X_LED_FORCE_MODE_MASK,
- QCA808X_LED_FORCE_EN | value ? QCA808X_LED_FORCE_ON :
- QCA808X_LED_FORCE_OFF);
-}
-
-static int qca808x_led_blink_set(struct phy_device *phydev, u8 index,
- unsigned long *delay_on,
- unsigned long *delay_off)
-{
- int ret;
- u16 reg;
-
- if (index > 2)
- return -EINVAL;
-
- reg = QCA808X_MMD7_LED_FORCE_CTRL(index);
-
- /* Set blink to 50% off, 50% on at 4Hz by default */
- ret = phy_modify_mmd(phydev, MDIO_MMD_AN, QCA808X_MMD7_LED_GLOBAL,
- QCA808X_LED_BLINK_FREQ_MASK | QCA808X_LED_BLINK_DUTY_MASK,
- QCA808X_LED_BLINK_FREQ_4HZ | QCA808X_LED_BLINK_DUTY_50_50);
- if (ret)
- return ret;
-
- /* We use BLINK_1 for normal blinking */
- ret = phy_modify_mmd(phydev, MDIO_MMD_AN, reg,
- QCA808X_LED_FORCE_EN | QCA808X_LED_FORCE_MODE_MASK,
- QCA808X_LED_FORCE_EN | QCA808X_LED_FORCE_BLINK_1);
- if (ret)
- return ret;
-
- /* We set blink to 4Hz, aka 250ms */
- *delay_on = 250 / 2;
- *delay_off = 250 / 2;
-
- return 0;
-}
-
-static int qca808x_led_polarity_set(struct phy_device *phydev, int index,
- unsigned long modes)
-{
- struct at803x_priv *priv = phydev->priv;
- bool active_low = false;
- u32 mode;
-
- for_each_set_bit(mode, &modes, __PHY_LED_MODES_NUM) {
- switch (mode) {
- case PHY_LED_ACTIVE_LOW:
- active_low = true;
- break;
- default:
- return -EINVAL;
- }
- }
-
- /* PHY polarity is global and can't be set per LED.
- * To detect this, check if last requested polarity mode
- * match the new one.
- */
- if (priv->led_polarity_mode >= 0 &&
- priv->led_polarity_mode != active_low) {
- phydev_err(phydev, "PHY polarity is global. Mismatched polarity on different LED\n");
- return -EINVAL;
- }
-
- /* Save the last PHY polarity mode */
- priv->led_polarity_mode = active_low;
-
- return phy_modify_mmd(phydev, MDIO_MMD_AN,
- QCA808X_MMD7_LED_POLARITY_CTRL,
- QCA808X_LED_ACTIVE_HIGH,
- active_low ? 0 : QCA808X_LED_ACTIVE_HIGH);
-}
-
static struct phy_driver at803x_driver[] = {
{
/* Qualcomm Atheros AR8035 */
.read_status = at803x_read_status,
.soft_reset = genphy_soft_reset,
.config_aneg = at803x_config_aneg,
-}, {
- /* Qualcomm QCA8081 */
- PHY_ID_MATCH_EXACT(QCA8081_PHY_ID),
- .name = "Qualcomm QCA8081",
- .flags = PHY_POLL_CABLE_TEST,
- .probe = at803x_probe,
- .config_intr = at803x_config_intr,
- .handle_interrupt = at803x_handle_interrupt,
- .get_tunable = at803x_get_tunable,
- .set_tunable = at803x_set_tunable,
- .set_wol = at803x_set_wol,
- .get_wol = at803x_get_wol,
- .get_features = qca808x_get_features,
- .config_aneg = qca808x_config_aneg,
- .suspend = genphy_suspend,
- .resume = genphy_resume,
- .read_status = qca808x_read_status,
- .config_init = qca808x_config_init,
- .soft_reset = qca808x_soft_reset,
- .cable_test_start = qca808x_cable_test_start,
- .cable_test_get_status = qca808x_cable_test_get_status,
- .link_change_notify = qca808x_link_change_notify,
- .led_brightness_set = qca808x_led_brightness_set,
- .led_blink_set = qca808x_led_blink_set,
- .led_hw_is_supported = qca808x_led_hw_is_supported,
- .led_hw_control_set = qca808x_led_hw_control_set,
- .led_hw_control_get = qca808x_led_hw_control_get,
- .led_polarity_set = qca808x_led_polarity_set,
}, };
module_phy_driver(at803x_driver);
{ PHY_ID_MATCH_EXACT(ATH8035_PHY_ID) },
{ PHY_ID_MATCH_EXACT(ATH9331_PHY_ID) },
{ PHY_ID_MATCH_EXACT(QCA9561_PHY_ID) },
- { PHY_ID_MATCH_EXACT(QCA8081_PHY_ID) },
{ }
};
--- /dev/null
+// SPDX-License-Identifier: GPL-2.0+
+
+#include <linux/phy.h>
+#include <linux/module.h>
+#include <linux/ethtool_netlink.h>
+
+#include "qcom.h"
+
+/* ADC threshold */
+#define QCA808X_PHY_DEBUG_ADC_THRESHOLD 0x2c80
+#define QCA808X_ADC_THRESHOLD_MASK GENMASK(7, 0)
+#define QCA808X_ADC_THRESHOLD_80MV 0
+#define QCA808X_ADC_THRESHOLD_100MV 0xf0
+#define QCA808X_ADC_THRESHOLD_200MV 0x0f
+#define QCA808X_ADC_THRESHOLD_300MV 0xff
+
+/* CLD control */
+#define QCA808X_PHY_MMD3_ADDR_CLD_CTRL7 0x8007
+#define QCA808X_8023AZ_AFE_CTRL_MASK GENMASK(8, 4)
+#define QCA808X_8023AZ_AFE_EN 0x90
+
+/* AZ control */
+#define QCA808X_PHY_MMD3_AZ_TRAINING_CTRL 0x8008
+#define QCA808X_MMD3_AZ_TRAINING_VAL 0x1c32
+
+#define QCA808X_PHY_MMD1_MSE_THRESHOLD_20DB 0x8014
+#define QCA808X_MSE_THRESHOLD_20DB_VALUE 0x529
+
+#define QCA808X_PHY_MMD1_MSE_THRESHOLD_17DB 0x800E
+#define QCA808X_MSE_THRESHOLD_17DB_VALUE 0x341
+
+#define QCA808X_PHY_MMD1_MSE_THRESHOLD_27DB 0x801E
+#define QCA808X_MSE_THRESHOLD_27DB_VALUE 0x419
+
+#define QCA808X_PHY_MMD1_MSE_THRESHOLD_28DB 0x8020
+#define QCA808X_MSE_THRESHOLD_28DB_VALUE 0x341
+
+#define QCA808X_PHY_MMD7_TOP_OPTION1 0x901c
+#define QCA808X_TOP_OPTION1_DATA 0x0
+
+#define QCA808X_PHY_MMD3_DEBUG_1 0xa100
+#define QCA808X_MMD3_DEBUG_1_VALUE 0x9203
+#define QCA808X_PHY_MMD3_DEBUG_2 0xa101
+#define QCA808X_MMD3_DEBUG_2_VALUE 0x48ad
+#define QCA808X_PHY_MMD3_DEBUG_3 0xa103
+#define QCA808X_MMD3_DEBUG_3_VALUE 0x1698
+#define QCA808X_PHY_MMD3_DEBUG_4 0xa105
+#define QCA808X_MMD3_DEBUG_4_VALUE 0x8001
+#define QCA808X_PHY_MMD3_DEBUG_5 0xa106
+#define QCA808X_MMD3_DEBUG_5_VALUE 0x1111
+#define QCA808X_PHY_MMD3_DEBUG_6 0xa011
+#define QCA808X_MMD3_DEBUG_6_VALUE 0x5f85
+
+/* master/slave seed config */
+#define QCA808X_PHY_DEBUG_LOCAL_SEED 9
+#define QCA808X_MASTER_SLAVE_SEED_ENABLE BIT(1)
+#define QCA808X_MASTER_SLAVE_SEED_CFG GENMASK(12, 2)
+#define QCA808X_MASTER_SLAVE_SEED_RANGE 0x32
+
+/* Hibernation yields lower power consumpiton in contrast with normal operation mode.
+ * when the copper cable is unplugged, the PHY enters into hibernation mode in about 10s.
+ */
+#define QCA808X_DBG_AN_TEST 0xb
+#define QCA808X_HIBERNATION_EN BIT(15)
+
+#define QCA808X_CDT_ENABLE_TEST BIT(15)
+#define QCA808X_CDT_INTER_CHECK_DIS BIT(13)
+#define QCA808X_CDT_STATUS BIT(11)
+#define QCA808X_CDT_LENGTH_UNIT BIT(10)
+
+#define QCA808X_MMD3_CDT_STATUS 0x8064
+#define QCA808X_MMD3_CDT_DIAG_PAIR_A 0x8065
+#define QCA808X_MMD3_CDT_DIAG_PAIR_B 0x8066
+#define QCA808X_MMD3_CDT_DIAG_PAIR_C 0x8067
+#define QCA808X_MMD3_CDT_DIAG_PAIR_D 0x8068
+#define QCA808X_CDT_DIAG_LENGTH_SAME_SHORT GENMASK(15, 8)
+#define QCA808X_CDT_DIAG_LENGTH_CROSS_SHORT GENMASK(7, 0)
+
+#define QCA808X_CDT_CODE_PAIR_A GENMASK(15, 12)
+#define QCA808X_CDT_CODE_PAIR_B GENMASK(11, 8)
+#define QCA808X_CDT_CODE_PAIR_C GENMASK(7, 4)
+#define QCA808X_CDT_CODE_PAIR_D GENMASK(3, 0)
+
+#define QCA808X_CDT_STATUS_STAT_TYPE GENMASK(1, 0)
+#define QCA808X_CDT_STATUS_STAT_FAIL FIELD_PREP_CONST(QCA808X_CDT_STATUS_STAT_TYPE, 0)
+#define QCA808X_CDT_STATUS_STAT_NORMAL FIELD_PREP_CONST(QCA808X_CDT_STATUS_STAT_TYPE, 1)
+#define QCA808X_CDT_STATUS_STAT_SAME_OPEN FIELD_PREP_CONST(QCA808X_CDT_STATUS_STAT_TYPE, 2)
+#define QCA808X_CDT_STATUS_STAT_SAME_SHORT FIELD_PREP_CONST(QCA808X_CDT_STATUS_STAT_TYPE, 3)
+
+#define QCA808X_CDT_STATUS_STAT_MDI GENMASK(3, 2)
+#define QCA808X_CDT_STATUS_STAT_MDI1 FIELD_PREP_CONST(QCA808X_CDT_STATUS_STAT_MDI, 1)
+#define QCA808X_CDT_STATUS_STAT_MDI2 FIELD_PREP_CONST(QCA808X_CDT_STATUS_STAT_MDI, 2)
+#define QCA808X_CDT_STATUS_STAT_MDI3 FIELD_PREP_CONST(QCA808X_CDT_STATUS_STAT_MDI, 3)
+
+/* NORMAL are MDI with type set to 0 */
+#define QCA808X_CDT_STATUS_STAT_CROSS_SHORT_WITH_MDI1_SAME_NORMAL QCA808X_CDT_STATUS_STAT_MDI1
+#define QCA808X_CDT_STATUS_STAT_CROSS_SHORT_WITH_MDI1_SAME_OPEN (QCA808X_CDT_STATUS_STAT_SAME_OPEN |\
+ QCA808X_CDT_STATUS_STAT_MDI1)
+#define QCA808X_CDT_STATUS_STAT_CROSS_SHORT_WITH_MDI1_SAME_SHORT (QCA808X_CDT_STATUS_STAT_SAME_SHORT |\
+ QCA808X_CDT_STATUS_STAT_MDI1)
+#define QCA808X_CDT_STATUS_STAT_CROSS_SHORT_WITH_MDI2_SAME_NORMAL QCA808X_CDT_STATUS_STAT_MDI2
+#define QCA808X_CDT_STATUS_STAT_CROSS_SHORT_WITH_MDI2_SAME_OPEN (QCA808X_CDT_STATUS_STAT_SAME_OPEN |\
+ QCA808X_CDT_STATUS_STAT_MDI2)
+#define QCA808X_CDT_STATUS_STAT_CROSS_SHORT_WITH_MDI2_SAME_SHORT (QCA808X_CDT_STATUS_STAT_SAME_SHORT |\
+ QCA808X_CDT_STATUS_STAT_MDI2)
+#define QCA808X_CDT_STATUS_STAT_CROSS_SHORT_WITH_MDI3_SAME_NORMAL QCA808X_CDT_STATUS_STAT_MDI3
+#define QCA808X_CDT_STATUS_STAT_CROSS_SHORT_WITH_MDI3_SAME_OPEN (QCA808X_CDT_STATUS_STAT_SAME_OPEN |\
+ QCA808X_CDT_STATUS_STAT_MDI3)
+#define QCA808X_CDT_STATUS_STAT_CROSS_SHORT_WITH_MDI3_SAME_SHORT (QCA808X_CDT_STATUS_STAT_SAME_SHORT |\
+ QCA808X_CDT_STATUS_STAT_MDI3)
+
+/* Added for reference of existence but should be handled by wait_for_completion already */
+#define QCA808X_CDT_STATUS_STAT_BUSY (BIT(1) | BIT(3))
+
+#define QCA808X_MMD7_LED_GLOBAL 0x8073
+#define QCA808X_LED_BLINK_1 GENMASK(11, 6)
+#define QCA808X_LED_BLINK_2 GENMASK(5, 0)
+/* Values are the same for both BLINK_1 and BLINK_2 */
+#define QCA808X_LED_BLINK_FREQ_MASK GENMASK(5, 3)
+#define QCA808X_LED_BLINK_FREQ_2HZ FIELD_PREP(QCA808X_LED_BLINK_FREQ_MASK, 0x0)
+#define QCA808X_LED_BLINK_FREQ_4HZ FIELD_PREP(QCA808X_LED_BLINK_FREQ_MASK, 0x1)
+#define QCA808X_LED_BLINK_FREQ_8HZ FIELD_PREP(QCA808X_LED_BLINK_FREQ_MASK, 0x2)
+#define QCA808X_LED_BLINK_FREQ_16HZ FIELD_PREP(QCA808X_LED_BLINK_FREQ_MASK, 0x3)
+#define QCA808X_LED_BLINK_FREQ_32HZ FIELD_PREP(QCA808X_LED_BLINK_FREQ_MASK, 0x4)
+#define QCA808X_LED_BLINK_FREQ_64HZ FIELD_PREP(QCA808X_LED_BLINK_FREQ_MASK, 0x5)
+#define QCA808X_LED_BLINK_FREQ_128HZ FIELD_PREP(QCA808X_LED_BLINK_FREQ_MASK, 0x6)
+#define QCA808X_LED_BLINK_FREQ_256HZ FIELD_PREP(QCA808X_LED_BLINK_FREQ_MASK, 0x7)
+#define QCA808X_LED_BLINK_DUTY_MASK GENMASK(2, 0)
+#define QCA808X_LED_BLINK_DUTY_50_50 FIELD_PREP(QCA808X_LED_BLINK_DUTY_MASK, 0x0)
+#define QCA808X_LED_BLINK_DUTY_75_25 FIELD_PREP(QCA808X_LED_BLINK_DUTY_MASK, 0x1)
+#define QCA808X_LED_BLINK_DUTY_25_75 FIELD_PREP(QCA808X_LED_BLINK_DUTY_MASK, 0x2)
+#define QCA808X_LED_BLINK_DUTY_33_67 FIELD_PREP(QCA808X_LED_BLINK_DUTY_MASK, 0x3)
+#define QCA808X_LED_BLINK_DUTY_67_33 FIELD_PREP(QCA808X_LED_BLINK_DUTY_MASK, 0x4)
+#define QCA808X_LED_BLINK_DUTY_17_83 FIELD_PREP(QCA808X_LED_BLINK_DUTY_MASK, 0x5)
+#define QCA808X_LED_BLINK_DUTY_83_17 FIELD_PREP(QCA808X_LED_BLINK_DUTY_MASK, 0x6)
+#define QCA808X_LED_BLINK_DUTY_8_92 FIELD_PREP(QCA808X_LED_BLINK_DUTY_MASK, 0x7)
+
+#define QCA808X_MMD7_LED2_CTRL 0x8074
+#define QCA808X_MMD7_LED2_FORCE_CTRL 0x8075
+#define QCA808X_MMD7_LED1_CTRL 0x8076
+#define QCA808X_MMD7_LED1_FORCE_CTRL 0x8077
+#define QCA808X_MMD7_LED0_CTRL 0x8078
+#define QCA808X_MMD7_LED_CTRL(x) (0x8078 - ((x) * 2))
+
+/* LED hw control pattern is the same for every LED */
+#define QCA808X_LED_PATTERN_MASK GENMASK(15, 0)
+#define QCA808X_LED_SPEED2500_ON BIT(15)
+#define QCA808X_LED_SPEED2500_BLINK BIT(14)
+/* Follow blink trigger even if duplex or speed condition doesn't match */
+#define QCA808X_LED_BLINK_CHECK_BYPASS BIT(13)
+#define QCA808X_LED_FULL_DUPLEX_ON BIT(12)
+#define QCA808X_LED_HALF_DUPLEX_ON BIT(11)
+#define QCA808X_LED_TX_BLINK BIT(10)
+#define QCA808X_LED_RX_BLINK BIT(9)
+#define QCA808X_LED_TX_ON_10MS BIT(8)
+#define QCA808X_LED_RX_ON_10MS BIT(7)
+#define QCA808X_LED_SPEED1000_ON BIT(6)
+#define QCA808X_LED_SPEED100_ON BIT(5)
+#define QCA808X_LED_SPEED10_ON BIT(4)
+#define QCA808X_LED_COLLISION_BLINK BIT(3)
+#define QCA808X_LED_SPEED1000_BLINK BIT(2)
+#define QCA808X_LED_SPEED100_BLINK BIT(1)
+#define QCA808X_LED_SPEED10_BLINK BIT(0)
+
+#define QCA808X_MMD7_LED0_FORCE_CTRL 0x8079
+#define QCA808X_MMD7_LED_FORCE_CTRL(x) (0x8079 - ((x) * 2))
+
+/* LED force ctrl is the same for every LED
+ * No documentation exist for this, not even internal one
+ * with NDA as QCOM gives only info about configuring
+ * hw control pattern rules and doesn't indicate any way
+ * to force the LED to specific mode.
+ * These define comes from reverse and testing and maybe
+ * lack of some info or some info are not entirely correct.
+ * For the basic LED control and hw control these finding
+ * are enough to support LED control in all the required APIs.
+ *
+ * On doing some comparison with implementation with qca807x,
+ * it was found that it's 1:1 equal to it and confirms all the
+ * reverse done. It was also found further specification with the
+ * force mode and the blink modes.
+ */
+#define QCA808X_LED_FORCE_EN BIT(15)
+#define QCA808X_LED_FORCE_MODE_MASK GENMASK(14, 13)
+#define QCA808X_LED_FORCE_BLINK_1 FIELD_PREP(QCA808X_LED_FORCE_MODE_MASK, 0x3)
+#define QCA808X_LED_FORCE_BLINK_2 FIELD_PREP(QCA808X_LED_FORCE_MODE_MASK, 0x2)
+#define QCA808X_LED_FORCE_ON FIELD_PREP(QCA808X_LED_FORCE_MODE_MASK, 0x1)
+#define QCA808X_LED_FORCE_OFF FIELD_PREP(QCA808X_LED_FORCE_MODE_MASK, 0x0)
+
+#define QCA808X_MMD7_LED_POLARITY_CTRL 0x901a
+/* QSDK sets by default 0x46 to this reg that sets BIT 6 for
+ * LED to active high. It's not clear what BIT 3 and BIT 4 does.
+ */
+#define QCA808X_LED_ACTIVE_HIGH BIT(6)
+
+/* QCA808X 1G chip type */
+#define QCA808X_PHY_MMD7_CHIP_TYPE 0x901d
+#define QCA808X_PHY_CHIP_TYPE_1G BIT(0)
+
+#define QCA8081_PHY_SERDES_MMD1_FIFO_CTRL 0x9072
+#define QCA8081_PHY_FIFO_RSTN BIT(11)
+
+#define QCA8081_PHY_ID 0x004dd101
+
+MODULE_DESCRIPTION("Qualcomm Atheros QCA808X PHY driver");
+MODULE_AUTHOR("Matus Ujhelyi");
+MODULE_LICENSE("GPL");
+
+struct qca808x_priv {
+ int led_polarity_mode;
+};
+
+static int qca808x_phy_fast_retrain_config(struct phy_device *phydev)
+{
+ int ret;
+
+ /* Enable fast retrain */
+ ret = genphy_c45_fast_retrain(phydev, true);
+ if (ret)
+ return ret;
+
+ phy_write_mmd(phydev, MDIO_MMD_AN, QCA808X_PHY_MMD7_TOP_OPTION1,
+ QCA808X_TOP_OPTION1_DATA);
+ phy_write_mmd(phydev, MDIO_MMD_PMAPMD, QCA808X_PHY_MMD1_MSE_THRESHOLD_20DB,
+ QCA808X_MSE_THRESHOLD_20DB_VALUE);
+ phy_write_mmd(phydev, MDIO_MMD_PMAPMD, QCA808X_PHY_MMD1_MSE_THRESHOLD_17DB,
+ QCA808X_MSE_THRESHOLD_17DB_VALUE);
+ phy_write_mmd(phydev, MDIO_MMD_PMAPMD, QCA808X_PHY_MMD1_MSE_THRESHOLD_27DB,
+ QCA808X_MSE_THRESHOLD_27DB_VALUE);
+ phy_write_mmd(phydev, MDIO_MMD_PMAPMD, QCA808X_PHY_MMD1_MSE_THRESHOLD_28DB,
+ QCA808X_MSE_THRESHOLD_28DB_VALUE);
+ phy_write_mmd(phydev, MDIO_MMD_PCS, QCA808X_PHY_MMD3_DEBUG_1,
+ QCA808X_MMD3_DEBUG_1_VALUE);
+ phy_write_mmd(phydev, MDIO_MMD_PCS, QCA808X_PHY_MMD3_DEBUG_4,
+ QCA808X_MMD3_DEBUG_4_VALUE);
+ phy_write_mmd(phydev, MDIO_MMD_PCS, QCA808X_PHY_MMD3_DEBUG_5,
+ QCA808X_MMD3_DEBUG_5_VALUE);
+ phy_write_mmd(phydev, MDIO_MMD_PCS, QCA808X_PHY_MMD3_DEBUG_3,
+ QCA808X_MMD3_DEBUG_3_VALUE);
+ phy_write_mmd(phydev, MDIO_MMD_PCS, QCA808X_PHY_MMD3_DEBUG_6,
+ QCA808X_MMD3_DEBUG_6_VALUE);
+ phy_write_mmd(phydev, MDIO_MMD_PCS, QCA808X_PHY_MMD3_DEBUG_2,
+ QCA808X_MMD3_DEBUG_2_VALUE);
+
+ return 0;
+}
+
+static int qca808x_phy_ms_seed_enable(struct phy_device *phydev, bool enable)
+{
+ u16 seed_value;
+
+ if (!enable)
+ return at803x_debug_reg_mask(phydev, QCA808X_PHY_DEBUG_LOCAL_SEED,
+ QCA808X_MASTER_SLAVE_SEED_ENABLE, 0);
+
+ seed_value = get_random_u32_below(QCA808X_MASTER_SLAVE_SEED_RANGE);
+ return at803x_debug_reg_mask(phydev, QCA808X_PHY_DEBUG_LOCAL_SEED,
+ QCA808X_MASTER_SLAVE_SEED_CFG | QCA808X_MASTER_SLAVE_SEED_ENABLE,
+ FIELD_PREP(QCA808X_MASTER_SLAVE_SEED_CFG, seed_value) |
+ QCA808X_MASTER_SLAVE_SEED_ENABLE);
+}
+
+static bool qca808x_is_prefer_master(struct phy_device *phydev)
+{
+ return (phydev->master_slave_get == MASTER_SLAVE_CFG_MASTER_FORCE) ||
+ (phydev->master_slave_get == MASTER_SLAVE_CFG_MASTER_PREFERRED);
+}
+
+static bool qca808x_has_fast_retrain_or_slave_seed(struct phy_device *phydev)
+{
+ return linkmode_test_bit(ETHTOOL_LINK_MODE_2500baseT_Full_BIT, phydev->supported);
+}
+
+static int qca808x_probe(struct phy_device *phydev)
+{
+ struct device *dev = &phydev->mdio.dev;
+ struct qca808x_priv *priv;
+
+ priv = devm_kzalloc(dev, sizeof(*priv), GFP_KERNEL);
+ if (!priv)
+ return -ENOMEM;
+
+ /* Init LED polarity mode to -1 */
+ priv->led_polarity_mode = -1;
+
+ phydev->priv = priv;
+
+ return 0;
+}
+
+static int qca808x_config_init(struct phy_device *phydev)
+{
+ int ret;
+
+ /* Active adc&vga on 802.3az for the link 1000M and 100M */
+ ret = phy_modify_mmd(phydev, MDIO_MMD_PCS, QCA808X_PHY_MMD3_ADDR_CLD_CTRL7,
+ QCA808X_8023AZ_AFE_CTRL_MASK, QCA808X_8023AZ_AFE_EN);
+ if (ret)
+ return ret;
+
+ /* Adjust the threshold on 802.3az for the link 1000M */
+ ret = phy_write_mmd(phydev, MDIO_MMD_PCS,
+ QCA808X_PHY_MMD3_AZ_TRAINING_CTRL,
+ QCA808X_MMD3_AZ_TRAINING_VAL);
+ if (ret)
+ return ret;
+
+ if (qca808x_has_fast_retrain_or_slave_seed(phydev)) {
+ /* Config the fast retrain for the link 2500M */
+ ret = qca808x_phy_fast_retrain_config(phydev);
+ if (ret)
+ return ret;
+
+ ret = genphy_read_master_slave(phydev);
+ if (ret < 0)
+ return ret;
+
+ if (!qca808x_is_prefer_master(phydev)) {
+ /* Enable seed and configure lower ramdom seed to make phy
+ * linked as slave mode.
+ */
+ ret = qca808x_phy_ms_seed_enable(phydev, true);
+ if (ret)
+ return ret;
+ }
+ }
+
+ /* Configure adc threshold as 100mv for the link 10M */
+ return at803x_debug_reg_mask(phydev, QCA808X_PHY_DEBUG_ADC_THRESHOLD,
+ QCA808X_ADC_THRESHOLD_MASK,
+ QCA808X_ADC_THRESHOLD_100MV);
+}
+
+static int qca808x_read_status(struct phy_device *phydev)
+{
+ struct at803x_ss_mask ss_mask = { 0 };
+ int ret;
+
+ ret = phy_read_mmd(phydev, MDIO_MMD_AN, MDIO_AN_10GBT_STAT);
+ if (ret < 0)
+ return ret;
+
+ linkmode_mod_bit(ETHTOOL_LINK_MODE_2500baseT_Full_BIT, phydev->lp_advertising,
+ ret & MDIO_AN_10GBT_STAT_LP2_5G);
+
+ ret = genphy_read_status(phydev);
+ if (ret)
+ return ret;
+
+ /* qca8081 takes the different bits for speed value from at803x */
+ ss_mask.speed_mask = QCA808X_SS_SPEED_MASK;
+ ss_mask.speed_shift = __bf_shf(QCA808X_SS_SPEED_MASK);
+ ret = at803x_read_specific_status(phydev, ss_mask);
+ if (ret < 0)
+ return ret;
+
+ if (phydev->link) {
+ if (phydev->speed == SPEED_2500)
+ phydev->interface = PHY_INTERFACE_MODE_2500BASEX;
+ else
+ phydev->interface = PHY_INTERFACE_MODE_SGMII;
+ } else {
+ /* generate seed as a lower random value to make PHY linked as SLAVE easily,
+ * except for master/slave configuration fault detected or the master mode
+ * preferred.
+ *
+ * the reason for not putting this code into the function link_change_notify is
+ * the corner case where the link partner is also the qca8081 PHY and the seed
+ * value is configured as the same value, the link can't be up and no link change
+ * occurs.
+ */
+ if (qca808x_has_fast_retrain_or_slave_seed(phydev)) {
+ if (phydev->master_slave_state == MASTER_SLAVE_STATE_ERR ||
+ qca808x_is_prefer_master(phydev)) {
+ qca808x_phy_ms_seed_enable(phydev, false);
+ } else {
+ qca808x_phy_ms_seed_enable(phydev, true);
+ }
+ }
+ }
+
+ return 0;
+}
+
+static int qca808x_soft_reset(struct phy_device *phydev)
+{
+ int ret;
+
+ ret = genphy_soft_reset(phydev);
+ if (ret < 0)
+ return ret;
+
+ if (qca808x_has_fast_retrain_or_slave_seed(phydev))
+ ret = qca808x_phy_ms_seed_enable(phydev, true);
+
+ return ret;
+}
+
+static bool qca808x_cdt_fault_length_valid(int cdt_code)
+{
+ switch (cdt_code) {
+ case QCA808X_CDT_STATUS_STAT_SAME_SHORT:
+ case QCA808X_CDT_STATUS_STAT_SAME_OPEN:
+ case QCA808X_CDT_STATUS_STAT_CROSS_SHORT_WITH_MDI1_SAME_NORMAL:
+ case QCA808X_CDT_STATUS_STAT_CROSS_SHORT_WITH_MDI1_SAME_OPEN:
+ case QCA808X_CDT_STATUS_STAT_CROSS_SHORT_WITH_MDI1_SAME_SHORT:
+ case QCA808X_CDT_STATUS_STAT_CROSS_SHORT_WITH_MDI2_SAME_NORMAL:
+ case QCA808X_CDT_STATUS_STAT_CROSS_SHORT_WITH_MDI2_SAME_OPEN:
+ case QCA808X_CDT_STATUS_STAT_CROSS_SHORT_WITH_MDI2_SAME_SHORT:
+ case QCA808X_CDT_STATUS_STAT_CROSS_SHORT_WITH_MDI3_SAME_NORMAL:
+ case QCA808X_CDT_STATUS_STAT_CROSS_SHORT_WITH_MDI3_SAME_OPEN:
+ case QCA808X_CDT_STATUS_STAT_CROSS_SHORT_WITH_MDI3_SAME_SHORT:
+ return true;
+ default:
+ return false;
+ }
+}
+
+static int qca808x_cable_test_result_trans(int cdt_code)
+{
+ switch (cdt_code) {
+ case QCA808X_CDT_STATUS_STAT_NORMAL:
+ return ETHTOOL_A_CABLE_RESULT_CODE_OK;
+ case QCA808X_CDT_STATUS_STAT_SAME_SHORT:
+ return ETHTOOL_A_CABLE_RESULT_CODE_SAME_SHORT;
+ case QCA808X_CDT_STATUS_STAT_SAME_OPEN:
+ return ETHTOOL_A_CABLE_RESULT_CODE_OPEN;
+ case QCA808X_CDT_STATUS_STAT_CROSS_SHORT_WITH_MDI1_SAME_NORMAL:
+ case QCA808X_CDT_STATUS_STAT_CROSS_SHORT_WITH_MDI1_SAME_OPEN:
+ case QCA808X_CDT_STATUS_STAT_CROSS_SHORT_WITH_MDI1_SAME_SHORT:
+ case QCA808X_CDT_STATUS_STAT_CROSS_SHORT_WITH_MDI2_SAME_NORMAL:
+ case QCA808X_CDT_STATUS_STAT_CROSS_SHORT_WITH_MDI2_SAME_OPEN:
+ case QCA808X_CDT_STATUS_STAT_CROSS_SHORT_WITH_MDI2_SAME_SHORT:
+ case QCA808X_CDT_STATUS_STAT_CROSS_SHORT_WITH_MDI3_SAME_NORMAL:
+ case QCA808X_CDT_STATUS_STAT_CROSS_SHORT_WITH_MDI3_SAME_OPEN:
+ case QCA808X_CDT_STATUS_STAT_CROSS_SHORT_WITH_MDI3_SAME_SHORT:
+ return ETHTOOL_A_CABLE_RESULT_CODE_CROSS_SHORT;
+ case QCA808X_CDT_STATUS_STAT_FAIL:
+ default:
+ return ETHTOOL_A_CABLE_RESULT_CODE_UNSPEC;
+ }
+}
+
+static int qca808x_cdt_fault_length(struct phy_device *phydev, int pair,
+ int result)
+{
+ int val;
+ u32 cdt_length_reg = 0;
+
+ switch (pair) {
+ case ETHTOOL_A_CABLE_PAIR_A:
+ cdt_length_reg = QCA808X_MMD3_CDT_DIAG_PAIR_A;
+ break;
+ case ETHTOOL_A_CABLE_PAIR_B:
+ cdt_length_reg = QCA808X_MMD3_CDT_DIAG_PAIR_B;
+ break;
+ case ETHTOOL_A_CABLE_PAIR_C:
+ cdt_length_reg = QCA808X_MMD3_CDT_DIAG_PAIR_C;
+ break;
+ case ETHTOOL_A_CABLE_PAIR_D:
+ cdt_length_reg = QCA808X_MMD3_CDT_DIAG_PAIR_D;
+ break;
+ default:
+ return -EINVAL;
+ }
+
+ val = phy_read_mmd(phydev, MDIO_MMD_PCS, cdt_length_reg);
+ if (val < 0)
+ return val;
+
+ if (result == ETHTOOL_A_CABLE_RESULT_CODE_SAME_SHORT)
+ val = FIELD_GET(QCA808X_CDT_DIAG_LENGTH_SAME_SHORT, val);
+ else
+ val = FIELD_GET(QCA808X_CDT_DIAG_LENGTH_CROSS_SHORT, val);
+
+ return at803x_cdt_fault_length(val);
+}
+
+static int qca808x_cable_test_start(struct phy_device *phydev)
+{
+ int ret;
+
+ /* perform CDT with the following configs:
+ * 1. disable hibernation.
+ * 2. force PHY working in MDI mode.
+ * 3. for PHY working in 1000BaseT.
+ * 4. configure the threshold.
+ */
+
+ ret = at803x_debug_reg_mask(phydev, QCA808X_DBG_AN_TEST, QCA808X_HIBERNATION_EN, 0);
+ if (ret < 0)
+ return ret;
+
+ ret = at803x_config_mdix(phydev, ETH_TP_MDI);
+ if (ret < 0)
+ return ret;
+
+ /* Force 1000base-T needs to configure PMA/PMD and MII_BMCR */
+ phydev->duplex = DUPLEX_FULL;
+ phydev->speed = SPEED_1000;
+ ret = genphy_c45_pma_setup_forced(phydev);
+ if (ret < 0)
+ return ret;
+
+ ret = genphy_setup_forced(phydev);
+ if (ret < 0)
+ return ret;
+
+ /* configure the thresholds for open, short, pair ok test */
+ phy_write_mmd(phydev, MDIO_MMD_PCS, 0x8074, 0xc040);
+ phy_write_mmd(phydev, MDIO_MMD_PCS, 0x8076, 0xc040);
+ phy_write_mmd(phydev, MDIO_MMD_PCS, 0x8077, 0xa060);
+ phy_write_mmd(phydev, MDIO_MMD_PCS, 0x8078, 0xc050);
+ phy_write_mmd(phydev, MDIO_MMD_PCS, 0x807a, 0xc060);
+ phy_write_mmd(phydev, MDIO_MMD_PCS, 0x807e, 0xb060);
+
+ return 0;
+}
+
+static int qca808x_cable_test_get_pair_status(struct phy_device *phydev, u8 pair,
+ u16 status)
+{
+ int length, result;
+ u16 pair_code;
+
+ switch (pair) {
+ case ETHTOOL_A_CABLE_PAIR_A:
+ pair_code = FIELD_GET(QCA808X_CDT_CODE_PAIR_A, status);
+ break;
+ case ETHTOOL_A_CABLE_PAIR_B:
+ pair_code = FIELD_GET(QCA808X_CDT_CODE_PAIR_B, status);
+ break;
+ case ETHTOOL_A_CABLE_PAIR_C:
+ pair_code = FIELD_GET(QCA808X_CDT_CODE_PAIR_C, status);
+ break;
+ case ETHTOOL_A_CABLE_PAIR_D:
+ pair_code = FIELD_GET(QCA808X_CDT_CODE_PAIR_D, status);
+ break;
+ default:
+ return -EINVAL;
+ }
+
+ result = qca808x_cable_test_result_trans(pair_code);
+ ethnl_cable_test_result(phydev, pair, result);
+
+ if (qca808x_cdt_fault_length_valid(pair_code)) {
+ length = qca808x_cdt_fault_length(phydev, pair, result);
+ ethnl_cable_test_fault_length(phydev, pair, length);
+ }
+
+ return 0;
+}
+
+static int qca808x_cable_test_get_status(struct phy_device *phydev, bool *finished)
+{
+ int ret, val;
+
+ *finished = false;
+
+ val = QCA808X_CDT_ENABLE_TEST |
+ QCA808X_CDT_LENGTH_UNIT;
+ ret = at803x_cdt_start(phydev, val);
+ if (ret)
+ return ret;
+
+ ret = at803x_cdt_wait_for_completion(phydev, QCA808X_CDT_ENABLE_TEST);
+ if (ret)
+ return ret;
+
+ val = phy_read_mmd(phydev, MDIO_MMD_PCS, QCA808X_MMD3_CDT_STATUS);
+ if (val < 0)
+ return val;
+
+ ret = qca808x_cable_test_get_pair_status(phydev, ETHTOOL_A_CABLE_PAIR_A, val);
+ if (ret)
+ return ret;
+
+ ret = qca808x_cable_test_get_pair_status(phydev, ETHTOOL_A_CABLE_PAIR_B, val);
+ if (ret)
+ return ret;
+
+ ret = qca808x_cable_test_get_pair_status(phydev, ETHTOOL_A_CABLE_PAIR_C, val);
+ if (ret)
+ return ret;
+
+ ret = qca808x_cable_test_get_pair_status(phydev, ETHTOOL_A_CABLE_PAIR_D, val);
+ if (ret)
+ return ret;
+
+ *finished = true;
+
+ return 0;
+}
+
+static int qca808x_get_features(struct phy_device *phydev)
+{
+ int ret;
+
+ ret = genphy_c45_pma_read_abilities(phydev);
+ if (ret)
+ return ret;
+
+ /* The autoneg ability is not existed in bit3 of MMD7.1,
+ * but it is supported by qca808x PHY, so we add it here
+ * manually.
+ */
+ linkmode_set_bit(ETHTOOL_LINK_MODE_Autoneg_BIT, phydev->supported);
+
+ /* As for the qca8081 1G version chip, the 2500baseT ability is also
+ * existed in the bit0 of MMD1.21, we need to remove it manually if
+ * it is the qca8081 1G chip according to the bit0 of MMD7.0x901d.
+ */
+ ret = phy_read_mmd(phydev, MDIO_MMD_AN, QCA808X_PHY_MMD7_CHIP_TYPE);
+ if (ret < 0)
+ return ret;
+
+ if (QCA808X_PHY_CHIP_TYPE_1G & ret)
+ linkmode_clear_bit(ETHTOOL_LINK_MODE_2500baseT_Full_BIT, phydev->supported);
+
+ return 0;
+}
+
+static int qca808x_config_aneg(struct phy_device *phydev)
+{
+ int phy_ctrl = 0;
+ int ret;
+
+ ret = at803x_prepare_config_aneg(phydev);
+ if (ret)
+ return ret;
+
+ /* The reg MII_BMCR also needs to be configured for force mode, the
+ * genphy_config_aneg is also needed.
+ */
+ if (phydev->autoneg == AUTONEG_DISABLE)
+ genphy_c45_pma_setup_forced(phydev);
+
+ if (linkmode_test_bit(ETHTOOL_LINK_MODE_2500baseT_Full_BIT, phydev->advertising))
+ phy_ctrl = MDIO_AN_10GBT_CTRL_ADV2_5G;
+
+ ret = phy_modify_mmd_changed(phydev, MDIO_MMD_AN, MDIO_AN_10GBT_CTRL,
+ MDIO_AN_10GBT_CTRL_ADV2_5G, phy_ctrl);
+ if (ret < 0)
+ return ret;
+
+ return __genphy_config_aneg(phydev, ret);
+}
+
+static void qca808x_link_change_notify(struct phy_device *phydev)
+{
+ /* Assert interface sgmii fifo on link down, deassert it on link up,
+ * the interface device address is always phy address added by 1.
+ */
+ mdiobus_c45_modify_changed(phydev->mdio.bus, phydev->mdio.addr + 1,
+ MDIO_MMD_PMAPMD, QCA8081_PHY_SERDES_MMD1_FIFO_CTRL,
+ QCA8081_PHY_FIFO_RSTN,
+ phydev->link ? QCA8081_PHY_FIFO_RSTN : 0);
+}
+
+static int qca808x_led_parse_netdev(struct phy_device *phydev, unsigned long rules,
+ u16 *offload_trigger)
+{
+ /* Parsing specific to netdev trigger */
+ if (test_bit(TRIGGER_NETDEV_TX, &rules))
+ *offload_trigger |= QCA808X_LED_TX_BLINK;
+ if (test_bit(TRIGGER_NETDEV_RX, &rules))
+ *offload_trigger |= QCA808X_LED_RX_BLINK;
+ if (test_bit(TRIGGER_NETDEV_LINK_10, &rules))
+ *offload_trigger |= QCA808X_LED_SPEED10_ON;
+ if (test_bit(TRIGGER_NETDEV_LINK_100, &rules))
+ *offload_trigger |= QCA808X_LED_SPEED100_ON;
+ if (test_bit(TRIGGER_NETDEV_LINK_1000, &rules))
+ *offload_trigger |= QCA808X_LED_SPEED1000_ON;
+ if (test_bit(TRIGGER_NETDEV_LINK_2500, &rules))
+ *offload_trigger |= QCA808X_LED_SPEED2500_ON;
+ if (test_bit(TRIGGER_NETDEV_HALF_DUPLEX, &rules))
+ *offload_trigger |= QCA808X_LED_HALF_DUPLEX_ON;
+ if (test_bit(TRIGGER_NETDEV_FULL_DUPLEX, &rules))
+ *offload_trigger |= QCA808X_LED_FULL_DUPLEX_ON;
+
+ if (rules && !*offload_trigger)
+ return -EOPNOTSUPP;
+
+ /* Enable BLINK_CHECK_BYPASS by default to make the LED
+ * blink even with duplex or speed mode not enabled.
+ */
+ *offload_trigger |= QCA808X_LED_BLINK_CHECK_BYPASS;
+
+ return 0;
+}
+
+static int qca808x_led_hw_control_enable(struct phy_device *phydev, u8 index)
+{
+ u16 reg;
+
+ if (index > 2)
+ return -EINVAL;
+
+ reg = QCA808X_MMD7_LED_FORCE_CTRL(index);
+
+ return phy_clear_bits_mmd(phydev, MDIO_MMD_AN, reg,
+ QCA808X_LED_FORCE_EN);
+}
+
+static int qca808x_led_hw_is_supported(struct phy_device *phydev, u8 index,
+ unsigned long rules)
+{
+ u16 offload_trigger = 0;
+
+ if (index > 2)
+ return -EINVAL;
+
+ return qca808x_led_parse_netdev(phydev, rules, &offload_trigger);
+}
+
+static int qca808x_led_hw_control_set(struct phy_device *phydev, u8 index,
+ unsigned long rules)
+{
+ u16 reg, offload_trigger = 0;
+ int ret;
+
+ if (index > 2)
+ return -EINVAL;
+
+ reg = QCA808X_MMD7_LED_CTRL(index);
+
+ ret = qca808x_led_parse_netdev(phydev, rules, &offload_trigger);
+ if (ret)
+ return ret;
+
+ ret = qca808x_led_hw_control_enable(phydev, index);
+ if (ret)
+ return ret;
+
+ return phy_modify_mmd(phydev, MDIO_MMD_AN, reg,
+ QCA808X_LED_PATTERN_MASK,
+ offload_trigger);
+}
+
+static bool qca808x_led_hw_control_status(struct phy_device *phydev, u8 index)
+{
+ u16 reg;
+ int val;
+
+ if (index > 2)
+ return false;
+
+ reg = QCA808X_MMD7_LED_FORCE_CTRL(index);
+
+ val = phy_read_mmd(phydev, MDIO_MMD_AN, reg);
+
+ return !(val & QCA808X_LED_FORCE_EN);
+}
+
+static int qca808x_led_hw_control_get(struct phy_device *phydev, u8 index,
+ unsigned long *rules)
+{
+ u16 reg;
+ int val;
+
+ if (index > 2)
+ return -EINVAL;
+
+ /* Check if we have hw control enabled */
+ if (qca808x_led_hw_control_status(phydev, index))
+ return -EINVAL;
+
+ reg = QCA808X_MMD7_LED_CTRL(index);
+
+ val = phy_read_mmd(phydev, MDIO_MMD_AN, reg);
+ if (val & QCA808X_LED_TX_BLINK)
+ set_bit(TRIGGER_NETDEV_TX, rules);
+ if (val & QCA808X_LED_RX_BLINK)
+ set_bit(TRIGGER_NETDEV_RX, rules);
+ if (val & QCA808X_LED_SPEED10_ON)
+ set_bit(TRIGGER_NETDEV_LINK_10, rules);
+ if (val & QCA808X_LED_SPEED100_ON)
+ set_bit(TRIGGER_NETDEV_LINK_100, rules);
+ if (val & QCA808X_LED_SPEED1000_ON)
+ set_bit(TRIGGER_NETDEV_LINK_1000, rules);
+ if (val & QCA808X_LED_SPEED2500_ON)
+ set_bit(TRIGGER_NETDEV_LINK_2500, rules);
+ if (val & QCA808X_LED_HALF_DUPLEX_ON)
+ set_bit(TRIGGER_NETDEV_HALF_DUPLEX, rules);
+ if (val & QCA808X_LED_FULL_DUPLEX_ON)
+ set_bit(TRIGGER_NETDEV_FULL_DUPLEX, rules);
+
+ return 0;
+}
+
+static int qca808x_led_hw_control_reset(struct phy_device *phydev, u8 index)
+{
+ u16 reg;
+
+ if (index > 2)
+ return -EINVAL;
+
+ reg = QCA808X_MMD7_LED_CTRL(index);
+
+ return phy_clear_bits_mmd(phydev, MDIO_MMD_AN, reg,
+ QCA808X_LED_PATTERN_MASK);
+}
+
+static int qca808x_led_brightness_set(struct phy_device *phydev,
+ u8 index, enum led_brightness value)
+{
+ u16 reg;
+ int ret;
+
+ if (index > 2)
+ return -EINVAL;
+
+ if (!value) {
+ ret = qca808x_led_hw_control_reset(phydev, index);
+ if (ret)
+ return ret;
+ }
+
+ reg = QCA808X_MMD7_LED_FORCE_CTRL(index);
+
+ return phy_modify_mmd(phydev, MDIO_MMD_AN, reg,
+ QCA808X_LED_FORCE_EN | QCA808X_LED_FORCE_MODE_MASK,
+ QCA808X_LED_FORCE_EN | value ? QCA808X_LED_FORCE_ON :
+ QCA808X_LED_FORCE_OFF);
+}
+
+static int qca808x_led_blink_set(struct phy_device *phydev, u8 index,
+ unsigned long *delay_on,
+ unsigned long *delay_off)
+{
+ int ret;
+ u16 reg;
+
+ if (index > 2)
+ return -EINVAL;
+
+ reg = QCA808X_MMD7_LED_FORCE_CTRL(index);
+
+ /* Set blink to 50% off, 50% on at 4Hz by default */
+ ret = phy_modify_mmd(phydev, MDIO_MMD_AN, QCA808X_MMD7_LED_GLOBAL,
+ QCA808X_LED_BLINK_FREQ_MASK | QCA808X_LED_BLINK_DUTY_MASK,
+ QCA808X_LED_BLINK_FREQ_4HZ | QCA808X_LED_BLINK_DUTY_50_50);
+ if (ret)
+ return ret;
+
+ /* We use BLINK_1 for normal blinking */
+ ret = phy_modify_mmd(phydev, MDIO_MMD_AN, reg,
+ QCA808X_LED_FORCE_EN | QCA808X_LED_FORCE_MODE_MASK,
+ QCA808X_LED_FORCE_EN | QCA808X_LED_FORCE_BLINK_1);
+ if (ret)
+ return ret;
+
+ /* We set blink to 4Hz, aka 250ms */
+ *delay_on = 250 / 2;
+ *delay_off = 250 / 2;
+
+ return 0;
+}
+
+static int qca808x_led_polarity_set(struct phy_device *phydev, int index,
+ unsigned long modes)
+{
+ struct qca808x_priv *priv = phydev->priv;
+ bool active_low = false;
+ u32 mode;
+
+ for_each_set_bit(mode, &modes, __PHY_LED_MODES_NUM) {
+ switch (mode) {
+ case PHY_LED_ACTIVE_LOW:
+ active_low = true;
+ break;
+ default:
+ return -EINVAL;
+ }
+ }
+
+ /* PHY polarity is global and can't be set per LED.
+ * To detect this, check if last requested polarity mode
+ * match the new one.
+ */
+ if (priv->led_polarity_mode >= 0 &&
+ priv->led_polarity_mode != active_low) {
+ phydev_err(phydev, "PHY polarity is global. Mismatched polarity on different LED\n");
+ return -EINVAL;
+ }
+
+ /* Save the last PHY polarity mode */
+ priv->led_polarity_mode = active_low;
+
+ return phy_modify_mmd(phydev, MDIO_MMD_AN,
+ QCA808X_MMD7_LED_POLARITY_CTRL,
+ QCA808X_LED_ACTIVE_HIGH,
+ active_low ? 0 : QCA808X_LED_ACTIVE_HIGH);
+}
+
+static struct phy_driver qca808x_driver[] = {
+{
+ /* Qualcomm QCA8081 */
+ PHY_ID_MATCH_EXACT(QCA8081_PHY_ID),
+ .name = "Qualcomm QCA8081",
+ .flags = PHY_POLL_CABLE_TEST,
+ .probe = qca808x_probe,
+ .config_intr = at803x_config_intr,
+ .handle_interrupt = at803x_handle_interrupt,
+ .get_tunable = at803x_get_tunable,
+ .set_tunable = at803x_set_tunable,
+ .set_wol = at803x_set_wol,
+ .get_wol = at803x_get_wol,
+ .get_features = qca808x_get_features,
+ .config_aneg = qca808x_config_aneg,
+ .suspend = genphy_suspend,
+ .resume = genphy_resume,
+ .read_status = qca808x_read_status,
+ .config_init = qca808x_config_init,
+ .soft_reset = qca808x_soft_reset,
+ .cable_test_start = qca808x_cable_test_start,
+ .cable_test_get_status = qca808x_cable_test_get_status,
+ .link_change_notify = qca808x_link_change_notify,
+ .led_brightness_set = qca808x_led_brightness_set,
+ .led_blink_set = qca808x_led_blink_set,
+ .led_hw_is_supported = qca808x_led_hw_is_supported,
+ .led_hw_control_set = qca808x_led_hw_control_set,
+ .led_hw_control_get = qca808x_led_hw_control_get,
+ .led_polarity_set = qca808x_led_polarity_set,
+}, };
+
+module_phy_driver(qca808x_driver);
+
+static struct mdio_device_id __maybe_unused qca808x_tbl[] = {
+ { PHY_ID_MATCH_EXACT(QCA8081_PHY_ID) },
+ { }
+};
+
+MODULE_DEVICE_TABLE(mdio, qca808x_tbl);
projects / linux.git / commitdiff