mmc: atmel-mci: move atmel MCI header file

Move the contents of linux/atmel-mci.h into
drivers/mmc/host/atmel-mci.c as it is only used in one file

Signed-off-by: Balamanikandan Gunasundar <balamanikandan.gunasundar@microchip.com>
Reviewed-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Link: https://lore.kernel.org/r/20230825095157.76073-3-balamanikandan.gunasundar@microchip.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

diff --git a/drivers/mmc/host/atmel-mci.c b/drivers/mmc/host/atmel-mci.c
index 892d29fed9ec88c3e37914a70027217f55b45c22..6f815818dd22b8eca8f2001b142a3a01ff68c15a 100644 (file)
--- a/drivers/mmc/host/atmel-mci.c
+++ b/drivers/mmc/host/atmel-mci.c
@@ -29,7 +29,6 @@
 #include <linux/mmc/host.h>
 #include <linux/mmc/sdio.h>
 
-#include <linux/atmel-mci.h>
 #include <linux/atmel_pdc.h>
 #include <linux/pm.h>
 #include <linux/pm_runtime.h>
@@ -39,6 +38,8 @@
 #include <asm/io.h>
 #include <asm/unaligned.h>
 
+#define ATMCI_MAX_NR_SLOTS     2
+
 /*
  * Superset of MCI IP registers integrated in Atmel AT91 Processor
  * Registers and bitfields marked with [2] are only available in MCI2
@@ -200,6 +201,42 @@ enum atmci_pdc_buf {
        PDC_SECOND_BUF,
 };
 
+/**
+ * struct mci_slot_pdata - board-specific per-slot configuration
+ * @bus_width: Number of data lines wired up the slot
+ * @detect_pin: GPIO pin wired to the card detect switch
+ * @wp_pin: GPIO pin wired to the write protect sensor
+ * @detect_is_active_high: The state of the detect pin when it is active
+ * @non_removable: The slot is not removable, only detect once
+ *
+ * If a given slot is not present on the board, @bus_width should be
+ * set to 0. The other fields are ignored in this case.
+ *
+ * Any pins that aren't available should be set to a negative value.
+ *
+ * Note that support for multiple slots is experimental -- some cards
+ * might get upset if we don't get the clock management exactly right.
+ * But in most cases, it should work just fine.
+ */
+struct mci_slot_pdata {
+       unsigned int            bus_width;
+       struct gpio_desc        *detect_pin;
+       struct gpio_desc        *wp_pin;
+       bool                    detect_is_active_high;
+       bool                    non_removable;
+};
+
+/**
+ * struct mci_platform_data - board-specific MMC/SDcard configuration
+ * @dma_slave: DMA slave interface to use in data transfers.
+ * @slot: Per-slot configuration data.
+ */
+struct mci_platform_data {
+       void                    *dma_slave;
+       dma_filter_fn           dma_filter;
+       struct mci_slot_pdata   slot[ATMCI_MAX_NR_SLOTS];
+};
+
 struct atmel_mci_caps {
        bool    has_dma_conf_reg;
        bool    has_pdc;

diff --git a/include/linux/atmel-mci.h b/include/linux/atmel-mci.h
deleted file mode 100644 (file)
index 017e7d8..0000000
--- a/include/linux/atmel-mci.h
+++ /dev/null
@@ -1,46 +0,0 @@
-/* SPDX-License-Identifier: GPL-2.0 */
-#ifndef __LINUX_ATMEL_MCI_H
-#define __LINUX_ATMEL_MCI_H
-
-#include <linux/types.h>
-#include <linux/dmaengine.h>
-
-#define ATMCI_MAX_NR_SLOTS     2
-
-/**
- * struct mci_slot_pdata - board-specific per-slot configuration
- * @bus_width: Number of data lines wired up the slot
- * @detect_pin: GPIO pin wired to the card detect switch
- * @wp_pin: GPIO pin wired to the write protect sensor
- * @detect_is_active_high: The state of the detect pin when it is active
- * @non_removable: The slot is not removable, only detect once
- *
- * If a given slot is not present on the board, @bus_width should be
- * set to 0. The other fields are ignored in this case.
- *
- * Any pins that aren't available should be set to a negative value.
- *
- * Note that support for multiple slots is experimental -- some cards
- * might get upset if we don't get the clock management exactly right.
- * But in most cases, it should work just fine.
- */
-struct mci_slot_pdata {
-       unsigned int            bus_width;
-       struct gpio_desc        *detect_pin;
-       struct gpio_desc        *wp_pin;
-       bool                    detect_is_active_high;
-       bool                    non_removable;
-};
-
-/**
- * struct mci_platform_data - board-specific MMC/SDcard configuration
- * @dma_slave: DMA slave interface to use in data transfers.
- * @slot: Per-slot configuration data.
- */
-struct mci_platform_data {
-       void                    *dma_slave;
-       dma_filter_fn           dma_filter;
-       struct mci_slot_pdata   slot[ATMCI_MAX_NR_SLOTS];
-};
-
-#endif /* __LINUX_ATMEL_MCI_H */