ALSA ALSA sound support is enabled.
APIC APIC support is enabled.
APM Advanced Power Management support is enabled.
+ APPARMOR AppArmor support is enabled.
ARM ARM architecture is enabled.
ARM64 ARM64 architecture is enabled.
AX25 Appropriate AX.25 support is enabled.
DYNAMIC_DEBUG Build in debug messages and enable them at runtime
EDD BIOS Enhanced Disk Drive Services (EDD) is enabled
EFI EFI Partitioning (GPT) is enabled
- EIDE EIDE/ATAPI support is enabled.
EVM Extended Verification Module
FB The frame buffer device is enabled.
FTRACE Function tracing enabled.
GCOV GCOV profiling is enabled.
+ HIBERNATION HIBERNATION is enabled.
HW Appropriate hardware is enabled.
+ HYPER_V HYPERV support is enabled.
IA-64 IA-64 architecture is enabled.
IMA Integrity measurement architecture is enabled.
- IOSCHED More than one I/O scheduler is enabled.
IP_PNP IP DHCP, BOOTP, or RARP is enabled.
IPV6 IPv6 support is enabled.
ISAPNP ISA PnP code is enabled.
NUMA NUMA support is enabled.
NFS Appropriate NFS support is enabled.
OF Devicetree is enabled.
- OSS OSS sound support is enabled.
PV_OPS A paravirtualized kernel is enabled.
PARIDE The ParIDE (parallel port IDE) subsystem is enabled.
PARISC The PA-RISC architecture is enabled.
the Documentation/scsi/ sub-directory.
SECURITY Different security models are enabled.
SELINUX SELinux support is enabled.
- APPARMOR AppArmor support is enabled.
SERIAL Serial support is enabled.
SH SuperH architecture is enabled.
SMP The kernel is an SMP kernel.
SWSUSP Software suspend (hibernation) is enabled.
SUSPEND System suspend states are enabled.
TPM TPM drivers are enabled.
- TS Appropriate touchscreen support is enabled.
UMS USB Mass Storage support is enabled.
USB USB support is enabled.
USBHID USB Human Interface Device support is enabled.
VGA The VGA console has been enabled.
VT Virtual terminal support is enabled.
WDT Watchdog support is enabled.
- XT IBM PC/XT MFM hard disk support is enabled.
X86-32 X86-32, aka i386 architecture is enabled.
X86-64 X86-64 architecture is enabled.
More X86-64 boot options can be found in
complete command line (parameters including spaces etc.) is limited to
a fixed number of characters. This limit depends on the architecture
and is between 256 and 4096 characters. It is defined in the file
-./include/asm/setup.h as COMMAND_LINE_SIZE.
+./include/uapi/asm-generic/setup.h as COMMAND_LINE_SIZE.
Finally, the [KMG] suffix is commonly described after a number of kernel
parameter values. These 'K', 'M', and 'G' letters represent the _binary_
cio_ignore= [S390]
See Documentation/s390/common_io.rst for details.
+
+ clearcpuid=BITNUM[,BITNUM...] [X86]
+ Disable CPUID feature X for the kernel. See
+ arch/x86/include/asm/cpufeatures.h for the valid bit
+ numbers. Note the Linux specific bits are not necessarily
+ stable over kernel options, but the vendor specific
+ ones should be.
+ Also note that user programs calling CPUID directly
+ or using the feature without checking anything
+ will still see it. This just prevents it from
+ being used by the kernel or shown in /proc/cpuinfo.
+ Also note the kernel might malfunction if you disable
+ some critical bits.
+
clk_ignore_unused
[CLK]
Prevents the clock framework from automatically gating
Defaults to zero when built as a module and to
10 seconds when built into the kernel.
- clearcpuid=BITNUM[,BITNUM...] [X86]
- Disable CPUID feature X for the kernel. See
- arch/x86/include/asm/cpufeatures.h for the valid bit
- numbers. Note the Linux specific bits are not necessarily
- stable over kernel options, but the vendor specific
- ones should be.
- Also note that user programs calling CPUID directly
- or using the feature without checking anything
- will still see it. This just prevents it from
- being used by the kernel or shown in /proc/cpuinfo.
- Also note the kernel might malfunction if you disable
- some critical bits.
-
cma=nn[MG]@[start[MG][-end[MG]]]
[KNL,CMA]
Sets the size of kernel global memory area for
dump out devices still on the deferred probe list after
retrying.
+ delayacct [KNL] Enable per-task delay accounting
+
dell_smm_hwmon.ignore_dmi=
[HW] Continue probing hardware even if DMI data
indicates that the driver is running on unsupported
disable= [IPV6]
See Documentation/networking/ipv6.rst.
- hardened_usercopy=
- [KNL] Under CONFIG_HARDENED_USERCOPY, whether
- hardening is enabled for this boot. Hardened
- usercopy checking is used to protect the kernel
- from reading or writing beyond known memory
- allocation boundaries as a proactive defense
- against bounds-checking flaws in the kernel's
- copy_to_user()/copy_from_user() interface.
- on Perform hardened usercopy checks (default).
- off Disable hardened usercopy checks.
-
disable_radix [PPC]
Disable RADIX MMU mode on POWER9
force: enforce the use of EDAC to report H/W event.
default: on.
- ekgdboc= [X86,KGDB] Allow early kernel console debugging
- ekgdboc=kbd
-
- This is designed to be used in conjunction with
- the boot argument: earlyprintk=vga
-
- This parameter works in place of the kgdboc parameter
- but can only be used if the backing tty is available
- very early in the boot process. For early debugging
- via a serial port see kgdboc_earlycon instead.
-
edd= [EDD]
Format: {"off" | "on" | "skip[mbr]"}
eisa_irq_edge= [PARISC,HW]
See header of drivers/parisc/eisa.c.
+ ekgdboc= [X86,KGDB] Allow early kernel console debugging
+ Format: ekgdboc=kbd
+
+ This is designed to be used in conjunction with
+ the boot argument: earlyprintk=vga
+
+ This parameter works in place of the kgdboc parameter
+ but can only be used if the backing tty is available
+ very early in the boot process. For early debugging
+ via a serial port see kgdboc_earlycon instead.
+
elanfreq= [X86-32]
See comment before function elanfreq_setup() in
arch/x86/kernel/cpu/cpufreq/elanfreq.c.
Format: <unsigned int> such that (rxsize & ~0x1fffc0) == 0.
Default: 1024
+ hardened_usercopy=
+ [KNL] Under CONFIG_HARDENED_USERCOPY, whether
+ hardening is enabled for this boot. Hardened
+ usercopy checking is used to protect the kernel
+ from reading or writing beyond known memory
+ allocation boundaries as a proactive defense
+ against bounds-checking flaws in the kernel's
+ copy_to_user()/copy_from_user() interface.
+ on Perform hardened usercopy checks (default).
+ off Disable hardened usercopy checks.
+
hardlockup_all_cpu_backtrace=
[KNL] Should the hard-lockup detector generate
backtraces on all cpus.
corresponding firmware-first mode error processing
logic will be disabled.
+ hibernate= [HIBERNATION]
+ noresume Don't check if there's a hibernation image
+ present during boot.
+ nocompress Don't compress/decompress hibernation images.
+ no Disable hibernation and resume.
+ protect_image Turn on image protection during restoration
+ (that will set all pages holding image data
+ during restoration read-only).
+
highmem=nn[KMG] [KNL,BOOT] forces the highmem zone to have an exact
size of <nn>. This works even on boxes that have no
highmem otherwise. This also works to reduce highmem
firmware feature for updating multiple TCE entries
at a time.
- onenand.bdry= [HW,MTD] Flex-OneNAND Boundary Configuration
-
- Format: [die0_boundary][,die0_lock][,die1_boundary][,die1_lock]
-
- boundary - index of last SLC block on Flex-OneNAND.
- The remaining blocks are configured as MLC blocks.
- lock - Configure if Flex-OneNAND boundary should be locked.
- Once locked, the boundary cannot be changed.
- 1 indicates lock status, 0 indicates unlock status.
-
mtdset= [ARM]
ARM/S3C2412 JIVE boot control
noclflush [BUGS=X86] Don't use the CLFLUSH instruction
- delayacct [KNL] Enable per-task delay accounting
-
nodsp [SH] Disable hardware DSP at boot time.
noefi Disable EFI runtime services support.
For example, to override I2C bus2:
omap_mux=i2c2_scl.i2c2_scl=0x100,i2c2_sda.i2c2_sda=0x100
+ onenand.bdry= [HW,MTD] Flex-OneNAND Boundary Configuration
+
+ Format: [die0_boundary][,die0_lock][,die1_boundary][,die1_lock]
+
+ boundary - index of last SLC block on Flex-OneNAND.
+ The remaining blocks are configured as MLC blocks.
+ lock - Configure if Flex-OneNAND boundary should be locked.
+ Once locked, the boundary cannot be changed.
+ 1 indicates lock status, 0 indicates unlock status.
+
oops=panic Always panic on oopses. Default is to just kill the
process, but there is a small probability of
deadlocking the machine.
Useful for devices that are detected asynchronously
(e.g. USB and MMC devices).
- hibernate= [HIBERNATION]
- noresume Don't check if there's a hibernation image
- present during boot.
- nocompress Don't compress/decompress hibernation images.
- no Disable hibernation and resume.
- protect_image Turn on image protection during restoration
- (that will set all pages holding image data
- during restoration read-only).
-
retain_initrd [RAM] Keep initrd memory after extraction
rfkill.default_state=
projects / linux.git / commitdiff