From: Arınç ÜNAL Date: Fri, 17 Mar 2023 21:30:03 +0000 (+0300) Subject: dt-bindings: pinctrl: mediatek: mt8195: rename to mediatek,mt8195-pinctrl X-Git-Url: http://git.maquefel.me/?a=commitdiff_plain;h=1d45ecb05ab4ec878254f2a11a5af49b64020148;p=linux.git dt-bindings: pinctrl: mediatek: mt8195: rename to mediatek,mt8195-pinctrl Rename pinctrl-mt8195.yaml to mediatek,mt8195-pinctrl.yaml to be on par with the compatible string and other mediatek dt-binding schemas. Signed-off-by: Arınç ÜNAL Acked-by: Rob Herring Link: https://lore.kernel.org/r/20230317213011.13656-14-arinc.unal@arinc9.com Signed-off-by: Linus Walleij --- diff --git a/Documentation/devicetree/bindings/pinctrl/mediatek,mt8195-pinctrl.yaml b/Documentation/devicetree/bindings/pinctrl/mediatek,mt8195-pinctrl.yaml new file mode 100644 index 0000000000000..7b3dfc14eedcf --- /dev/null +++ b/Documentation/devicetree/bindings/pinctrl/mediatek,mt8195-pinctrl.yaml @@ -0,0 +1,287 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/pinctrl/mediatek,mt8195-pinctrl.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Mediatek MT8195 Pin Controller + +maintainers: + - Sean Wang + +description: | + The Mediatek's Pin controller is used to control SoC pins. + +properties: + compatible: + const: mediatek,mt8195-pinctrl + + gpio-controller: true + + '#gpio-cells': + description: | + Number of cells in GPIO specifier. Since the generic GPIO binding is used, + the amount of cells must be specified as 2. See the below + mentioned gpio binding representation for description of particular cells. + const: 2 + + gpio-ranges: + description: gpio valid number range. + maxItems: 1 + + gpio-line-names: true + + reg: + description: | + Physical address base for gpio base registers. There are 8 GPIO + physical address base in mt8195. + maxItems: 8 + + reg-names: + description: | + Gpio base register names. + maxItems: 8 + + interrupt-controller: true + + '#interrupt-cells': + const: 2 + + interrupts: + description: The interrupt outputs to sysirq. + maxItems: 1 + + mediatek,rsel-resistance-in-si-unit: + type: boolean + description: | + Identifying i2c pins pull up/down type which is RSEL. It can support + RSEL define or si unit value(ohm) to set different resistance. + +# PIN CONFIGURATION NODES +patternProperties: + '-pins$': + type: object + additionalProperties: false + patternProperties: + '^pins': + type: object + additionalProperties: false + description: | + A pinctrl node should contain at least one subnodes representing the + pinctrl groups available on the machine. Each subnode will list the + pins it needs, and how they should be configured, with regard to muxer + configuration, pullups, drive strength, input enable/disable and + input schmitt. + An example of using macro: + pincontroller { + /* GPIO0 set as multifunction GPIO0 */ + gpio-pins { + pins { + pinmux = ; + } + }; + /* GPIO8 set as multifunction SDA0 */ + i2c0-pins { + pins { + pinmux = ; + } + }; + }; + $ref: "pinmux-node.yaml" + + properties: + pinmux: + description: | + Integer array, represents gpio pin number and mux setting. + Supported pin number and mux varies for different SoCs, and are + defined as macros in dt-bindings/pinctrl/-pinfunc.h + directly. + + drive-strength: + enum: [2, 4, 6, 8, 10, 12, 14, 16] + + drive-strength-microamp: + enum: [125, 250, 500, 1000] + + bias-pull-down: + oneOf: + - type: boolean + - enum: [100, 101, 102, 103] + description: mt8195 pull down PUPD/R0/R1 type define value. + - enum: [200, 201, 202, 203, 204, 205, 206, 207] + description: mt8195 pull down RSEL type define value. + - enum: [75000, 5000] + description: mt8195 pull down RSEL type si unit value(ohm). + description: | + For pull down type is normal, it don't need add RSEL & R1R0 define + and resistance value. + For pull down type is PUPD/R0/R1 type, it can add R1R0 define to + set different resistance. It can support "MTK_PUPD_SET_R1R0_00" & + "MTK_PUPD_SET_R1R0_01" & "MTK_PUPD_SET_R1R0_10" & + "MTK_PUPD_SET_R1R0_11" define in mt8195. + For pull down type is RSEL, it can add RSEL define & resistance + value(ohm) to set different resistance by identifying property + "mediatek,rsel-resistance-in-si-unit". + It can support "MTK_PULL_SET_RSEL_000" & "MTK_PULL_SET_RSEL_001" + & "MTK_PULL_SET_RSEL_010" & "MTK_PULL_SET_RSEL_011" + & "MTK_PULL_SET_RSEL_100" & "MTK_PULL_SET_RSEL_101" + & "MTK_PULL_SET_RSEL_110" & "MTK_PULL_SET_RSEL_111" + define in mt8195. It can also support resistance value(ohm) + "75000" & "5000" in mt8195. + + An example of using RSEL define: + pincontroller { + i2c0_pin { + pins { + pinmux = ; + bias-pull-down = ; + } + }; + }; + An example of using si unit resistance value(ohm): + &pio { + mediatek,rsel-resistance-in-si-unit; + } + pincontroller { + i2c0_pin { + pins { + pinmux = ; + bias-pull-down = <75000>; + } + }; + }; + + bias-pull-up: + oneOf: + - type: boolean + - enum: [100, 101, 102, 103] + description: mt8195 pull up PUPD/R0/R1 type define value. + - enum: [200, 201, 202, 203, 204, 205, 206, 207] + description: mt8195 pull up RSEL type define value. + - enum: [1000, 1500, 2000, 3000, 4000, 5000, 10000, 75000] + description: mt8195 pull up RSEL type si unit value(ohm). + description: | + For pull up type is normal, it don't need add RSEL & R1R0 define + and resistance value. + For pull up type is PUPD/R0/R1 type, it can add R1R0 define to + set different resistance. It can support "MTK_PUPD_SET_R1R0_00" & + "MTK_PUPD_SET_R1R0_01" & "MTK_PUPD_SET_R1R0_10" & + "MTK_PUPD_SET_R1R0_11" define in mt8195. + For pull up type is RSEL, it can add RSEL define & resistance + value(ohm) to set different resistance by identifying property + "mediatek,rsel-resistance-in-si-unit". + It can support "MTK_PULL_SET_RSEL_000" & "MTK_PULL_SET_RSEL_001" + & "MTK_PULL_SET_RSEL_010" & "MTK_PULL_SET_RSEL_011" + & "MTK_PULL_SET_RSEL_100" & "MTK_PULL_SET_RSEL_101" + & "MTK_PULL_SET_RSEL_110" & "MTK_PULL_SET_RSEL_111" + define in mt8195. It can also support resistance value(ohm) + "1000" & "1500" & "2000" & "3000" & "4000" & "5000" & "10000" & + "75000" in mt8195. + An example of using RSEL define: + pincontroller { + i2c0-pins { + pins { + pinmux = ; + bias-pull-up = ; + } + }; + }; + An example of using si unit resistance value(ohm): + &pio { + mediatek,rsel-resistance-in-si-unit; + } + pincontroller { + i2c0-pins { + pins { + pinmux = ; + bias-pull-up = <1000>; + } + }; + }; + + bias-disable: true + + output-high: true + + output-low: true + + input-enable: true + + input-disable: true + + input-schmitt-enable: true + + input-schmitt-disable: true + + required: + - pinmux + +allOf: + - $ref: "pinctrl.yaml#" + +required: + - compatible + - reg + - interrupts + - interrupt-controller + - '#interrupt-cells' + - gpio-controller + - '#gpio-cells' + - gpio-ranges + +additionalProperties: false + +examples: + - | + #include + #include + # + pio: pinctrl@10005000 { + compatible = "mediatek,mt8195-pinctrl"; + reg = <0x10005000 0x1000>, + <0x11d10000 0x1000>, + <0x11d30000 0x1000>, + <0x11d40000 0x1000>, + <0x11e20000 0x1000>, + <0x11eb0000 0x1000>, + <0x11f40000 0x1000>, + <0x1000b000 0x1000>; + reg-names = "iocfg0", "iocfg_bm", "iocfg_bl", + "iocfg_br", "iocfg_lm", "iocfg_rb", + "iocfg_tl", "eint"; + gpio-controller; + #gpio-cells = <2>; + gpio-ranges = <&pio 0 0 144>; + interrupt-controller; + interrupts = ; + #interrupt-cells = <2>; + + pio-pins { + pins { + pinmux = ; + output-low; + }; + }; + + spi0-pins { + pins-spi { + pinmux = , + , + ; + bias-disable; + }; + pins-spi-mi { + pinmux = ; + bias-pull-down; + }; + }; + + i2c0-pins { + pins { + pinmux = , + ; + bias-disable; + drive-strength-microamp = <1000>; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/pinctrl/pinctrl-mt8195.yaml b/Documentation/devicetree/bindings/pinctrl/pinctrl-mt8195.yaml deleted file mode 100644 index 66fe17e9e4d33..0000000000000 --- a/Documentation/devicetree/bindings/pinctrl/pinctrl-mt8195.yaml +++ /dev/null @@ -1,287 +0,0 @@ -# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) -%YAML 1.2 ---- -$id: http://devicetree.org/schemas/pinctrl/pinctrl-mt8195.yaml# -$schema: http://devicetree.org/meta-schemas/core.yaml# - -title: Mediatek MT8195 Pin Controller - -maintainers: - - Sean Wang - -description: | - The Mediatek's Pin controller is used to control SoC pins. - -properties: - compatible: - const: mediatek,mt8195-pinctrl - - gpio-controller: true - - '#gpio-cells': - description: | - Number of cells in GPIO specifier. Since the generic GPIO binding is used, - the amount of cells must be specified as 2. See the below - mentioned gpio binding representation for description of particular cells. - const: 2 - - gpio-ranges: - description: gpio valid number range. - maxItems: 1 - - gpio-line-names: true - - reg: - description: | - Physical address base for gpio base registers. There are 8 GPIO - physical address base in mt8195. - maxItems: 8 - - reg-names: - description: | - Gpio base register names. - maxItems: 8 - - interrupt-controller: true - - '#interrupt-cells': - const: 2 - - interrupts: - description: The interrupt outputs to sysirq. - maxItems: 1 - - mediatek,rsel-resistance-in-si-unit: - type: boolean - description: | - Identifying i2c pins pull up/down type which is RSEL. It can support - RSEL define or si unit value(ohm) to set different resistance. - -# PIN CONFIGURATION NODES -patternProperties: - '-pins$': - type: object - additionalProperties: false - patternProperties: - '^pins': - type: object - additionalProperties: false - description: | - A pinctrl node should contain at least one subnodes representing the - pinctrl groups available on the machine. Each subnode will list the - pins it needs, and how they should be configured, with regard to muxer - configuration, pullups, drive strength, input enable/disable and - input schmitt. - An example of using macro: - pincontroller { - /* GPIO0 set as multifunction GPIO0 */ - gpio-pins { - pins { - pinmux = ; - } - }; - /* GPIO8 set as multifunction SDA0 */ - i2c0-pins { - pins { - pinmux = ; - } - }; - }; - $ref: "pinmux-node.yaml" - - properties: - pinmux: - description: | - Integer array, represents gpio pin number and mux setting. - Supported pin number and mux varies for different SoCs, and are - defined as macros in dt-bindings/pinctrl/-pinfunc.h - directly. - - drive-strength: - enum: [2, 4, 6, 8, 10, 12, 14, 16] - - drive-strength-microamp: - enum: [125, 250, 500, 1000] - - bias-pull-down: - oneOf: - - type: boolean - - enum: [100, 101, 102, 103] - description: mt8195 pull down PUPD/R0/R1 type define value. - - enum: [200, 201, 202, 203, 204, 205, 206, 207] - description: mt8195 pull down RSEL type define value. - - enum: [75000, 5000] - description: mt8195 pull down RSEL type si unit value(ohm). - description: | - For pull down type is normal, it don't need add RSEL & R1R0 define - and resistance value. - For pull down type is PUPD/R0/R1 type, it can add R1R0 define to - set different resistance. It can support "MTK_PUPD_SET_R1R0_00" & - "MTK_PUPD_SET_R1R0_01" & "MTK_PUPD_SET_R1R0_10" & - "MTK_PUPD_SET_R1R0_11" define in mt8195. - For pull down type is RSEL, it can add RSEL define & resistance - value(ohm) to set different resistance by identifying property - "mediatek,rsel-resistance-in-si-unit". - It can support "MTK_PULL_SET_RSEL_000" & "MTK_PULL_SET_RSEL_001" - & "MTK_PULL_SET_RSEL_010" & "MTK_PULL_SET_RSEL_011" - & "MTK_PULL_SET_RSEL_100" & "MTK_PULL_SET_RSEL_101" - & "MTK_PULL_SET_RSEL_110" & "MTK_PULL_SET_RSEL_111" - define in mt8195. It can also support resistance value(ohm) - "75000" & "5000" in mt8195. - - An example of using RSEL define: - pincontroller { - i2c0_pin { - pins { - pinmux = ; - bias-pull-down = ; - } - }; - }; - An example of using si unit resistance value(ohm): - &pio { - mediatek,rsel-resistance-in-si-unit; - } - pincontroller { - i2c0_pin { - pins { - pinmux = ; - bias-pull-down = <75000>; - } - }; - }; - - bias-pull-up: - oneOf: - - type: boolean - - enum: [100, 101, 102, 103] - description: mt8195 pull up PUPD/R0/R1 type define value. - - enum: [200, 201, 202, 203, 204, 205, 206, 207] - description: mt8195 pull up RSEL type define value. - - enum: [1000, 1500, 2000, 3000, 4000, 5000, 10000, 75000] - description: mt8195 pull up RSEL type si unit value(ohm). - description: | - For pull up type is normal, it don't need add RSEL & R1R0 define - and resistance value. - For pull up type is PUPD/R0/R1 type, it can add R1R0 define to - set different resistance. It can support "MTK_PUPD_SET_R1R0_00" & - "MTK_PUPD_SET_R1R0_01" & "MTK_PUPD_SET_R1R0_10" & - "MTK_PUPD_SET_R1R0_11" define in mt8195. - For pull up type is RSEL, it can add RSEL define & resistance - value(ohm) to set different resistance by identifying property - "mediatek,rsel-resistance-in-si-unit". - It can support "MTK_PULL_SET_RSEL_000" & "MTK_PULL_SET_RSEL_001" - & "MTK_PULL_SET_RSEL_010" & "MTK_PULL_SET_RSEL_011" - & "MTK_PULL_SET_RSEL_100" & "MTK_PULL_SET_RSEL_101" - & "MTK_PULL_SET_RSEL_110" & "MTK_PULL_SET_RSEL_111" - define in mt8195. It can also support resistance value(ohm) - "1000" & "1500" & "2000" & "3000" & "4000" & "5000" & "10000" & - "75000" in mt8195. - An example of using RSEL define: - pincontroller { - i2c0-pins { - pins { - pinmux = ; - bias-pull-up = ; - } - }; - }; - An example of using si unit resistance value(ohm): - &pio { - mediatek,rsel-resistance-in-si-unit; - } - pincontroller { - i2c0-pins { - pins { - pinmux = ; - bias-pull-up = <1000>; - } - }; - }; - - bias-disable: true - - output-high: true - - output-low: true - - input-enable: true - - input-disable: true - - input-schmitt-enable: true - - input-schmitt-disable: true - - required: - - pinmux - -allOf: - - $ref: "pinctrl.yaml#" - -required: - - compatible - - reg - - interrupts - - interrupt-controller - - '#interrupt-cells' - - gpio-controller - - '#gpio-cells' - - gpio-ranges - -additionalProperties: false - -examples: - - | - #include - #include - # - pio: pinctrl@10005000 { - compatible = "mediatek,mt8195-pinctrl"; - reg = <0x10005000 0x1000>, - <0x11d10000 0x1000>, - <0x11d30000 0x1000>, - <0x11d40000 0x1000>, - <0x11e20000 0x1000>, - <0x11eb0000 0x1000>, - <0x11f40000 0x1000>, - <0x1000b000 0x1000>; - reg-names = "iocfg0", "iocfg_bm", "iocfg_bl", - "iocfg_br", "iocfg_lm", "iocfg_rb", - "iocfg_tl", "eint"; - gpio-controller; - #gpio-cells = <2>; - gpio-ranges = <&pio 0 0 144>; - interrupt-controller; - interrupts = ; - #interrupt-cells = <2>; - - pio-pins { - pins { - pinmux = ; - output-low; - }; - }; - - spi0-pins { - pins-spi { - pinmux = , - , - ; - bias-disable; - }; - pins-spi-mi { - pinmux = ; - bias-pull-down; - }; - }; - - i2c0-pins { - pins { - pinmux = , - ; - bias-disable; - drive-strength-microamp = <1000>; - }; - }; - };