From: Max Krummenacher <max.krummenacher@toradex.com>
Date: Wed, 15 Jun 2022 11:49:55 +0000 (+0200)
Subject: ARM: dts: imx6q-apalis: Move Atmel MXT touch ctrl to SoM dtsi
X-Git-Url: http://git.maquefel.me/?a=commitdiff_plain;h=2c119c4d9cdf208f94aaa8e1b4af7981d9a4b532;p=linux.git

ARM: dts: imx6q-apalis: Move Atmel MXT touch ctrl to SoM dtsi

Reduces code duplication. While at it drop the comments which do not
apply on Apalis iMX6 but add the correct SoM pin names.

Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
---

diff --git a/arch/arm/boot/dts/imx6q-apalis-eval.dts b/arch/arm/boot/dts/imx6q-apalis-eval.dts
index fe5d491e13994..5985d1169be13 100644
--- a/arch/arm/boot/dts/imx6q-apalis-eval.dts
+++ b/arch/arm/boot/dts/imx6q-apalis-eval.dts
@@ -82,19 +82,6 @@
 &i2c1 {
 	status = "okay";
 
-	/*
-	 * Touchscreen is using SODIMM 28/30, also used for PWM<B>, PWM<C>,
-	 * aka pwm2, pwm3. so if you enable touchscreen, disable the pwms
-	 */
-	touchscreen@4a {
-		compatible = "atmel,maxtouch";
-		reg = <0x4a>;
-		interrupt-parent = <&gpio6>;
-		interrupts = <10 IRQ_TYPE_EDGE_FALLING>;
-		reset-gpios = <&gpio6 9 GPIO_ACTIVE_LOW>; /* SODIMM 13 */
-		status = "disabled";
-	};
-
 	pcie-switch@58 {
 		compatible = "plx,pex8605";
 		reg = <0x58>;
diff --git a/arch/arm/boot/dts/imx6q-apalis-ixora-v1.1.dts b/arch/arm/boot/dts/imx6q-apalis-ixora-v1.1.dts
index 8febfc0aea93f..21f88e19e87d5 100644
--- a/arch/arm/boot/dts/imx6q-apalis-ixora-v1.1.dts
+++ b/arch/arm/boot/dts/imx6q-apalis-ixora-v1.1.dts
@@ -89,19 +89,6 @@
 &i2c1 {
 	status = "okay";
 
-	/*
-	 * Touchscreen is using SODIMM 28/30, also used for PWM<B>, PWM<C>,
-	 * aka pwm2, pwm3. so if you enable touchscreen, disable the pwms
-	 */
-	touchscreen@4a {
-		compatible = "atmel,maxtouch";
-		reg = <0x4a>;
-		interrupt-parent = <&gpio6>;
-		interrupts = <10 IRQ_TYPE_EDGE_FALLING>;
-		reset-gpios = <&gpio6 9 GPIO_ACTIVE_LOW>; /* SODIMM 13 */
-		status = "disabled";
-	};
-
 	/* M41T0M6 real time clock on carrier board */
 	rtc_i2c: rtc@68 {
 		compatible = "st,m41t0";
diff --git a/arch/arm/boot/dts/imx6q-apalis-ixora.dts b/arch/arm/boot/dts/imx6q-apalis-ixora.dts
index 78cf1d9583c1a..6743617ad1c1f 100644
--- a/arch/arm/boot/dts/imx6q-apalis-ixora.dts
+++ b/arch/arm/boot/dts/imx6q-apalis-ixora.dts
@@ -88,19 +88,6 @@
 &i2c1 {
 	status = "okay";
 
-	/*
-	 * Touchscreen is using SODIMM 28/30, also used for PWM<B>, PWM<C>,
-	 * aka pwm2, pwm3. so if you enable touchscreen, disable the pwms
-	 */
-	touchscreen@4a {
-		compatible = "atmel,maxtouch";
-		reg = <0x4a>;
-		interrupt-parent = <&gpio6>;
-		interrupts = <10 IRQ_TYPE_EDGE_FALLING>;
-		reset-gpios = <&gpio6 9 GPIO_ACTIVE_LOW>; /* SODIMM 13 */
-		status = "disabled";
-	};
-
 	eeprom@50 {
 		compatible = "atmel,24c02";
 		reg = <0x50>;
diff --git a/arch/arm/boot/dts/imx6qdl-apalis.dtsi b/arch/arm/boot/dts/imx6qdl-apalis.dtsi
index 9413c14ce5f68..3aa66b6d0c88c 100644
--- a/arch/arm/boot/dts/imx6qdl-apalis.dtsi
+++ b/arch/arm/boot/dts/imx6qdl-apalis.dtsi
@@ -416,6 +416,17 @@
 	scl-gpios = <&gpio5 27 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
 	sda-gpios = <&gpio5 26 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
 	status = "disabled";
+
+	atmel_mxt_ts: touchscreen@4a {
+		compatible = "atmel,maxtouch";
+		/* These GPIOs are muxed with the iomuxc node */
+		interrupt-parent = <&gpio6>;
+		interrupts = <10 IRQ_TYPE_EDGE_FALLING>;	/* MXM3_11 */
+		reg = <0x4a>;
+		reset-gpios = <&gpio6 9 GPIO_ACTIVE_LOW>;	/* MXM3_13 */
+		status = "disabled";
+	};
+
 };
 
 /*