pcie: expire pending delete

Add an expire time for pending delete, once the time is over allow
pressing the attention button again.

This makes pcie hotplug behave more like acpi hotplug, where one can
try sending an 'device_del' monitor command again in case the guest
didn't respond to the first attempt.

Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Message-Id: <20211111130859.1171890-7-kraxel@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>

pcie: fast unplug when slot power is off

In case the slot is powered off (and the power indicator turned off too)
we can unplug right away, without round-trip to the guest.

Also clear pending attention button press, there is nothing to care
about any more.

Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Message-Id: <20211111130859.1171890-6-kraxel@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>

pcie: factor out pcie_cap_slot_unplug()

No functional change.

Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Message-Id: <20211111130859.1171890-5-kraxel@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>

pcie: add power indicator blink check

Refuse to push the attention button in case the guest is busy with some
hotplug operation (as indicated by the power indicator blinking).

Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Message-Id: <20211111130859.1171890-4-kraxel@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>

pcie: implement slot power control for pcie root ports

With this patch hot-plugged pci devices will only be visible to the
guest if the guests hotplug driver has enabled slot power.

This should fix the hot-plug race which one can hit when hot-plugging
a pci device at boot, while the guest is in the middle of the pci bus
scan.

Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Message-Id: <20211111130859.1171890-3-kraxel@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>

pci: implement power state

This allows to power off pci devices.  In "off" state the devices will
not be visible.  No pci config space access, no pci bar access, no dma.

Default state is "on", so this patch (alone) should not change behavior.

Use case:  Allows hotplug controllers implement slot power.  Hotplug
controllers doing so should set the inital power state for devices in
the ->plug callback.

Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Message-Id: <20211111130859.1171890-2-kraxel@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>

vdpa: Check for existence of opts.vhostdev

Since net_init_vhost_vdpa is trying to open it. Not specifying it in the
command line crash qemu.

Fixes: 7327813d17 ("vhost-vdpa: open device fd in net_init_vhost_vdpa()")
Signed-off-by: Eugenio Pérez <eperezma@redhat.com>
Message-Id: <20211112193431.2379298-3-eperezma@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>

vdpa: Replace qemu_open_old by qemu_open at

There is no reason to keep using the old one, since we neither use the
variadics arguments nor open it with O_DIRECT.

Also, net_client_init1, the caller of net_init_vhost_vdpa, wants all
net_client_init_fun to use Error API, so it's a good step in that
direction.

Signed-off-by: Eugenio Pérez <eperezma@redhat.com>
Message-Id: <20211112193431.2379298-2-eperezma@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>

virtio: use virtio accessor to access packed event

We used to access packed descriptor event and off_wrap via
address_space_{write|read}_cached(). When we hit the cache, memcpy()
is used which is not atomic which may lead a wrong value to be read or
wrote.

This patch fixes this by switching to use
virito_{stw|lduw}_phys_cached() to make sure the access is atomic.

Fixes: 683f7665679c1 ("virtio: event suppression support for packed ring")
Cc: qemu-stable@nongnu.org
Signed-off-by: Jason Wang <jasowang@redhat.com>
Message-Id: <20211111063854.29060-2-jasowang@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>

virtio: use virtio accessor to access packed descriptor flags

We used to access packed descriptor flags via
address_space_{write|read}_cached(). When we hit the cache, memcpy()
is used which is not an atomic operation which may lead a wrong value
is read or wrote.

So this patch switches to use virito_{stw|lduw}_phys_cached() to make
sure the aceess is atomic.

Fixes: 86044b24e865f ("virtio: basic packed virtqueue support")
Cc: qemu-stable@nongnu.org
Signed-off-by: Jason Wang <jasowang@redhat.com>
Message-Id: <20211111063854.29060-1-jasowang@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>

tests: bios-tables-test update expected blobs

The changes are the result of
        'hw/i386/acpi-build: Deny control on PCIe Native Hot-Plug in _OSC'
which hides PCIE hotplug bit in host-bridge _OSC

Method (_OSC, 4, NotSerialized)  // _OSC: Operating System Capabilities
             {
                 CreateDWordField (Arg3, Zero, CDW1)
                 If ((Arg0 == ToUUID ("33db4d5b-1ff7-401c-9657-7441c03dd766") /* PCI Host Bridge Device */))
                 {
                     CreateDWordField (Arg3, 0x04, CDW2)
                     CreateDWordField (Arg3, 0x08, CDW3)
                     Local0 = CDW3 /* \_SB_.PCI0._OSC.CDW3 */
-                    Local0 &= 0x1F
+                    Local0 &= 0x1E

Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Message-Id: <20211112110857.3116853-6-imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>

hw/i386/acpi-build: Deny control on PCIe Native Hot-plug in _OSC

There are two ways to enable ACPI PCI Hot-plug:

        * Disable the Hot-plug Capable bit on PCIe slots.

This was the first approach which led to regression [1-2], as
I/O space for a port is allocated only when it is hot-pluggable,
which is determined by HPC bit.

        * Leave the HPC bit on and disable PCIe Native Hot-plug in _OSC
          method.

This removes the (future) ability of hot-plugging switches with PCIe
Native hotplug since ACPI PCI Hot-plug only works with cold-plugged
bridges. If the user wants to explicitely use this feature, they can
disable ACPI PCI Hot-plug with:
        --global ICH9-LPC.acpi-pci-hotplug-with-bridge-support=off

Change the bit in _OSC method so that the OS selects ACPI PCI Hot-plug
instead of PCIe Native.

[1] https://gitlab.com/qemu-project/qemu/-/issues/641
[2] https://bugzilla.redhat.com/show_bug.cgi?id=2006409

Signed-off-by: Julia Suvorova <jusual@redhat.com>
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Message-Id: <20211112110857.3116853-5-imammedo@redhat.com>
Reviewed-by: Ani Sinha <ani@anisinha.ca>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>

bios-tables-test: Allow changes in DSDT ACPI tables

Prepare for changing the _OSC method in q35 DSDT.

Signed-off-by: Julia Suvorova <jusual@redhat.com>
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Acked-by: Ani Sinha <ani@anisinha.ca>
Message-Id: <20211112110857.3116853-4-imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>

hw/acpi/ich9: Add compat prop to keep HPC bit set for 6.1 machine type

To solve issues [1-2] the Hot Plug Capable bit in PCIe Slots will be
turned on, while the switch to ACPI Hot-plug will be done in the
DSDT table.

Introducing 'x-keep-native-hpc' property disables the HPC bit only
in 6.1 and as a result keeps the forced 'reserve-io' on
pcie-root-ports in 6.1 too.

[1] https://gitlab.com/qemu-project/qemu/-/issues/641
[2] https://bugzilla.redhat.com/show_bug.cgi?id=2006409

Signed-off-by: Julia Suvorova <jusual@redhat.com>
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Message-Id: <20211112110857.3116853-3-imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>

pcie: rename 'native-hotplug' to 'x-native-hotplug'

Mark property as experimental/internal adding 'x-' prefix.

Property was introduced in 6.1 and it should have provided
ability to turn on native PCIE hotplug on port even when
ACPI PCI hotplug is in use is user explicitly sets property
on CLI. However that never worked since slot is wired to
ACPI hotplug controller.
Another non-intended usecase: disable native hotplug on slot
when APCI based hotplug is disabled, which works but slot has
'hotplug' property for this taks.

It should be relatively safe to rename it to experimental
as no users should exist for it and given that the property
is broken we don't really want to leave it around for much
longer lest users start using it.

Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Ani Sinha <ani@anisinha.ca>
Message-Id: <20211112110857.3116853-2-imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>

hw/mem/pc-dimm: Restrict NUMA-specific code to NUMA machines

When trying to use the pc-dimm device on a non-NUMA machine, we get:

  $ qemu-system-arm -M none -cpu max -S \
      -object memory-backend-file,id=mem1,size=1M,mem-path=/tmp/1m \
      -device pc-dimm,id=dimm1,memdev=mem1
  Segmentation fault (core dumped)

  (gdb) bt
  #0  pc_dimm_realize (dev=0x555556da3e90, errp=0x7fffffffcd10) at hw/mem/pc-dimm.c:184
  #1  0x0000555555fe1f8f in device_set_realized (obj=0x555556da3e90, value=true, errp=0x7fffffffce18) at hw/core/qdev.c:531
  #2  0x0000555555feb4a9 in property_set_bool (obj=0x555556da3e90, v=0x555556e54420, name=0x5555563c3c41 "realized", opaque=0x555556a704f0, errp=0x7fffffffce18) at qom/object.c:2257

To avoid that crash, restrict the pc-dimm NUMA check to machines
supporting NUMA, and do not allow the use of 'node' property on
non-NUMA machines.

Suggested-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20211106145016.611332-1-f4bug@amsat.org>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>

vhost: Fix last vq queue index of devices with no cvq

The -1 assumes that cvq device model is accounted in data_queue_pairs,
if cvq does not exists, but it's actually the opposite: Devices with
!cvq are ok but devices with cvq does not add the last queue to
data_queue_pairs.

This is not a problem to vhost-net, but it is to vhost-vdpa:
* Devices with cvq gets initialized at last data vq device model, not
at cvq one.
* Devices with !cvq never gets initialized, since last_index is the
first queue of the last device model.

Because of that, the right change in last_index is to actually add the
cvq, not to remove the missing one.

This is not a problem to vhost-net, but it is to vhost-vdpa, which
device model trust to reach the last index to finish starting the
device.

Also, as the previous commit, rename it to index_end.

Tested with vp_vdpa with host's vhost=on and vhost=off, with ctrl_vq=on
and ctrl_vq=off.

Fixes: 049eb15b5fc9 ("vhost: record the last virtqueue index for the virtio device")
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Eugenio Pérez <eperezma@redhat.com>
Message-Id: <20211104085625.2054959-3-eperezma@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>

vhost: Rename last_index to vq_index_end

The doc of this field pointed out that last_index is the last vq index.
This is misleading, since it's actually one past the end of the vqs.

Renaming and modifying comment.

Signed-off-by: Eugenio Pérez <eperezma@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Message-Id: <20211104085625.2054959-2-eperezma@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>

softmmu/qdev-monitor: fix use-after-free in qdev_set_id()

Reported by Coverity (CID 1465222).

Fixes: 4a1d937796de0fecd8b22d7dbebf87f38e8282fd ("softmmu/qdev-monitor: add error handling in qdev_set_id")
Cc: Damien Hedde <damien.hedde@greensocs.com>
Cc: Kevin Wolf <kwolf@redhat.com>
Cc: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-Id: <20211102163342.31162-1-stefanha@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Damien Hedde <damien.hedde@greensocs.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>

net/vhost-vdpa: fix memory leak in vhost_vdpa_get_max_queue_pairs()

Use g_autofree to ensure that `config` is freed when
vhost_vdpa_get_max_queue_pairs() returns.

Reported-by: Coverity (CID 1465228: RESOURCE_LEAK)
Fixes: 402378407d ("vhost-vdpa: multiqueue support")
Signed-off-by: Stefano Garzarella <sgarzare@redhat.com>
Message-Id: <20211102155157.241034-1-sgarzare@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>

Update version for v6.2.0-rc0 release

Signed-off-by: Richard Henderson <richard.henderson@linaro.org>

Merge tag 'q800-for-6.2-pull-request' of git://github.com/vivier/qemu-m68k into staging

Fix CID 1465231

# gpg: Signature made Tue 09 Nov 2021 04:46:03 PM CET
# gpg:                using RSA key CD2F75DDC8E3A4DC2E4F5173F30C38BD3F2FBE3C
# gpg:                issuer "laurent@vivier.eu"
# gpg: Good signature from "Laurent Vivier <lvivier@redhat.com>" [full]
# gpg:                 aka "Laurent Vivier <laurent@vivier.eu>" [full]
# gpg:                 aka "Laurent Vivier (Red Hat) <lvivier@redhat.com>" [full]

* tag 'q800-for-6.2-pull-request' of git://github.com/vivier/qemu-m68k:
  macfb: fix a memory leak (CID 1465231)

Signed-off-by: Richard Henderson <richard.henderson@linaro.org>

macfb: fix a memory leak (CID 1465231)

Rewrite the function using g_string_append_printf() rather than
g_strdup_printf()/g_strconcat().

Fixes: df8abbbadf74 ("macfb: add common monitor modes supported by the MacOS toolbox ROM")
Cc: mark.cave-ayland@ilande.co.uk
Reported-by: Peter Maydell <peter.maydell@linaro.org>
Suggested-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Message-Id: <20211105165254.3544369-1-laurent@vivier.eu>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>

Merge tag 'm68k-for-6.2-pull-request' of git://github.com/vivier/qemu-m68k into staging

m68k pull request 20211109

Add virt machine types for 6.1 and 6.2

# gpg: Signature made Tue 09 Nov 2021 12:14:39 PM CET
# gpg:                using RSA key CD2F75DDC8E3A4DC2E4F5173F30C38BD3F2FBE3C
# gpg:                issuer "laurent@vivier.eu"
# gpg: Good signature from "Laurent Vivier <lvivier@redhat.com>" [full]
# gpg:                 aka "Laurent Vivier <laurent@vivier.eu>" [full]
# gpg:                 aka "Laurent Vivier (Red Hat) <lvivier@redhat.com>" [full]

* tag 'm68k-for-6.2-pull-request' of git://github.com/vivier/qemu-m68k:
  hw: m68k: virt: Add compat machine for 6.2
  hw: m68k: virt: Add compat machine for 6.1

Signed-off-by: Richard Henderson <richard.henderson@linaro.org>

hw: m68k: virt: Add compat machine for 6.2

Add the missing machine type for m68k/virt

Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20211106194158.4068596-3-laurent@vivier.eu>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>

hw: m68k: virt: Add compat machine for 6.1

Add the missing machine type for m68k/virt

Cc: qemu-stable@nongnu.org
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20211106194158.4068596-2-laurent@vivier.eu>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>

Merge remote-tracking branch 'remotes/vivier/tags/trivial-branch-for-6.2-pull-request' into staging

Trivial branch patches pull request 20211109

# gpg: Signature made Tue 09 Nov 2021 10:12:04 AM CET
# gpg:                using RSA key CD2F75DDC8E3A4DC2E4F5173F30C38BD3F2FBE3C
# gpg:                issuer "laurent@vivier.eu"
# gpg: Good signature from "Laurent Vivier <lvivier@redhat.com>" [full]
# gpg:                 aka "Laurent Vivier <laurent@vivier.eu>" [full]
# gpg:                 aka "Laurent Vivier (Red Hat) <lvivier@redhat.com>" [full]

* remotes/vivier/tags/trivial-branch-for-6.2-pull-request:
  docs/about/deprecated: Remove empty 'related binaries' section
  tests/qtest/virtio-net: fix hotplug test case
  meson: Fix 'interpretor' typo
  .mailmap: Fix more contributor entries
  hw/m68k: Fix typo in SPDX tag
  hmp: Add shortcut to stop command to match cont

Signed-off-by: Richard Henderson <richard.henderson@linaro.org>

docs/about/deprecated: Remove empty 'related binaries' section

Commit 497a30dbb06 ("qemu-img: Require -F with -b backing image")
removed the content of the "Related binaries" section but forgot
to remove the section title. Since it is now empty, remove it too.

Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Willian Rampazzo <willianr@redhat.com>
Reviewed-by: Yanan Wang <wangyanan55@huawei.com>
Reviewed-by: Joaquin de Andres <me@xcancerberox.com.ar>
Message-Id: <20211105142656.145791-1-philmd@redhat.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>

tests/qtest/virtio-net: fix hotplug test case

virtio-net-test has an hotplug testcase that is never executed.

This is because the testcase is attached to virtio-pci interface
rather than to virtio-net-pci.

  $ QTEST_QEMU_BINARY=./qemu-system-x86_64 tests/qtest/qos-test -l | grep hotplug
  /x86_64/.../pci-ohci-tests/ohci_pci-test-hotplug
  /x86_64/.../e1000e/e1000e-tests/hotplug
  /x86_64/.../virtio-blk-pci/virtio-blk-pci-tests/hotplug
  /x86_64/.../vhost-user-blk-pci/vhost-user-blk-pci-tests/hotplug
  /x86_64/.../virtio-rng-pci/virtio-rng-pci-tests/hotplug
  /x86_64/.../virtio-scsi/virtio-scsi-tests/hotplug
  /x86_64/.../virtio-serial/virtio-serial-tests/hotplug

With this fix:

  $ QTEST_QEMU_BINARY=./qemu-system-x86_64 tests/qtest/qos-test -l | grep hotplug
  ...
  /x86_64/.../vhost-user-blk-pci/vhost-user-blk-pci-tests/hotplug
  /x86_64/.../virtio-net-pci/virtio-net-pci-tests/hotplug
  /x86_64/.../virtio-rng-pci/virtio-rng-pci-tests/hotplug
  ...
  $ QTEST_QEMU_BINARY=./qemu-system-x86_64 tests/qtest/qos-test -p /x86_64/.../virtio-net-pci-tests/hotplug
  /x86_64/pc/i440FX-pcihost/pci-bus-pc/pci-bus/virtio-net-pci/virtio-net-pci-tests/hotplug: OK

Fixes: 6ae333f91b99 ("qos-test: virtio-net test node")
Signed-off-by: Laurent Vivier <lvivier@redhat.com>
Acked-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20211028173014.139692-1-lvivier@redhat.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>

meson: Fix 'interpretor' typo

Fix a typo from commit fa2f7b0b9b7 ("meson: Warn when TCI is
selected but TCG backend is available").

Reported-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20210521103423.2780345-1-philmd@redhat.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>

.mailmap: Fix more contributor entries

These authors have some incorrect author email field.

Acked-by: Pan Nengyuan <pannengyuan@huawei.com>
Reviewed-by: Alex Chen <alex.chen@huawei.com>
Reviewed-by: Hyman Huang <huangy81@chinatelecom.cn>
Reviewed-by: Haibin Zhang <haibinzhang@tencent.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20211027043254.1248097-1-f4bug@amsat.org>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>

hw/m68k: Fix typo in SPDX tag

Fix 'Identifer' -> 'Identifier' typo.

Cc: Laurent Vivier <laurent@vivier.eu>
Fixes: 8c6df16ff60 ("hw/char: add goldfish-tty")
Fixes: 87855593903 ("hw/intc: add goldfish-pic")
Fixes: 2fde99ee312 ("m68k: add an interrupt controller")
Fixes: 0791bc02b8f ("m68k: add a system controller")
Fixes: e1cecdca559 ("m68k: add Virtual M68k Machine")
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20211103105311.3399293-1-f4bug@amsat.org>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>

hmp: Add shortcut to stop command to match cont

Some commands such as quit or cont have one letter alternatives but
stop is missing that. Add stop|s to match cont|c for consistency and
convenience.

Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Message-Id: <20211030095225.513D4748F48@zero.eik.bme.hu>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>

Merge remote-tracking branch 'remotes/juanquintela/tags/migration-20211109-pull-request' into staging

Migration Pull request

Hi

This pull request includes:
- fix sample-pages doc by hyman
- cleanup colo pages by contiguous blocks by Rao
- reset auto-converge by checkpoint by Rao.

Please, apply.

# gpg: Signature made Tue 09 Nov 2021 09:02:37 AM CET
# gpg:                using RSA key 1899FF8EDEBF58CCEE034B82F487EF185872D723
# gpg: Good signature from "Juan Quintela <quintela@redhat.com>" [full]
# gpg:                 aka "Juan Quintela <quintela@trasno.org>" [full]

* remotes/juanquintela/tags/migration-20211109-pull-request:
  Reset the auto-converge counter at every checkpoint.
  Reduce the PVM stop time during Checkpoint
  docs: fix 'sample-pages' option tag

Signed-off-by: Richard Henderson <richard.henderson@linaro.org>

Reset the auto-converge counter at every checkpoint.

if we don't reset the auto-converge counter,
it will continue to run with COLO running,
and eventually the system will hang due to the
CPU throttle reaching DEFAULT_MIGRATE_MAX_CPU_THROTTLE.

Signed-off-by: Lei Rao <lei.rao@intel.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Lukas Straub <lukasstraub2@web.de>
Tested-by: Lukas Straub <lukasstraub2@web.de>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>

Reduce the PVM stop time during Checkpoint

When flushing memory from ram cache to ram during every checkpoint
on secondary VM, we can copy continuous chunks of memory instead of
4096 bytes per time to reduce the time of VM stop during checkpoint.

Signed-off-by: Lei Rao <lei.rao@intel.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Lukas Straub <lukasstraub2@web.de>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Tested-by: Lukas Straub <lukasstraub2@web.de>
Signed-off-by: Juan Quintela <quintela@redhat.com>

docs: fix 'sample-pages' option tag

commit f78d4ed701 has fixed qemu tag, making 'sample-pages' option tag
involved by accident, which introduced since 6.1 in commit 7afa08cd8fd.
revert this line.

Signed-off-by: Hyman Huang(黄勇) <huangy81@chinatelecom.cn>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>

Merge remote-tracking branch 'remotes/dgibson/tags/ppc-for-6.2-20211109' into staging

ppc patch queue for 2021-11-09

Here's the latest set of ppc related patches for qemu-6.2, which I
hope will squeeze in just barely before the hard freeze.

This set includes a change to MAINTAINERS moving maintainership of ppc
from myself and Greg Kurz to Cédric le Goater and Daniel Henrique
Barboza.  So, I expect this to be my last pull request as ppc
maintainer.  It's been great, but it's time I moved onto other things.

Apart from that, this patchset is mostly a lot of updates to TCG
implementations of ISA 3.1 (POWER10) instructions from the El Dorado
team.  There are also a handful of other fixes.

# gpg: Signature made Tue 09 Nov 2021 05:14:33 AM CET
# gpg:                using RSA key 75F46586AE61A66CC44E87DC6C38CACA20D9B392
# gpg: Good signature from "David Gibson <david@gibson.dropbear.id.au>" [full]
# gpg:                 aka "David Gibson (kernel.org) <dwg@kernel.org>" [unknown]
# gpg:                 aka "David Gibson (Red Hat) <dgibson@redhat.com>" [full]
# gpg:                 aka "David Gibson (ozlabs.org) <dgibson@ozlabs.org>" [full]

* remotes/dgibson/tags/ppc-for-6.2-20211109: (54 commits)
  spapr_numa.c: FORM2 table handle nodes with no distance info
  target/ppc, hw/ppc: Change maintainers
  target/ppc: cntlzdm/cnttzdm implementation without brcond
  target/ppc: Implement lxvkq instruction
  target/ppc: Implement xxblendvb/xxblendvh/xxblendvw/xxblendvd instructions
  target/ppc: implemented XXSPLTIDP instruction
  target/ppc: Implemented XXSPLTIW using decodetree
  target/ppc: implemented XXSPLTI32DX
  target/ppc: moved XXSPLTIB to using decodetree
  target/ppc: moved XXSPLTW to using decodetree
  target/ppc: added the instructions PLXVP and PSTXVP
  target/ppc: added the instructions PLXV and PSTXV
  target/ppc: added the instructions LXVPX and STXVPX
  target/ppc: added the instructions LXVP and STXVP
  target/ppc: moved stxvx and lxvx from legacy to decodtree
  target/ppc: moved stxv and lxv from legacy to decodtree
  target/ppc: receive high/low as argument in get/set_cpu_vsr
  target/ppc: Introduce REQUIRE_VSX macro
  target/ppc: Implement Vector Extract Double to VSR using GPR index insns
  target/ppc: Move vinsertb/vinserth/vinsertw/vinsertd to decodetree
  ...

Signed-off-by: Richard Henderson <richard.henderson@linaro.org>

spapr_numa.c: FORM2 table handle nodes with no distance info

A configuration that specifies multiple nodes without distance info
results in the non-local points in the FORM2 matrix having a distance of
0. This causes Linux to complain "Invalid distance value range" because
a node distance is smaller than the local distance.

Fix this by building a simple local / remote fallback for points where
distance information is missing.

Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Message-Id: <20211105135137.1584840-1-npiggin@gmail.com>
Reviewed-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>

target/ppc, hw/ppc: Change maintainers

As our day jobs and interests have moved onto other things, Greg and I have
been struggling to keep on top of maintainership of target/ppc and
associated pieces like the pseries and powernv machine types, with their
platform specific devices.

We've therefore discussed and plan to transfer maintainership to Cédric Le
Goater (primary) and Daniel Henrique Barboza (backup).  Cédric and Daniel
have been actively contributing to the area for some time, and they're
supported in this by their current employer, IBM, who has an obvious
interest in the platform.

Greg and I do plan to stay around in some capacity for at least the next
6 months, providing reviews and advice to assist the new maintainers into
the role.

Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Reviewed-by: Greg Kurz <groug@kaod.org>
Acked-by: Cédric Le Goater <clg@kaod.org>

target/ppc: cntlzdm/cnttzdm implementation without brcond

Suggested-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Matheus Ferst <matheus.ferst@eldorado.org.br>
Message-Id: <20211104123719.323713-26-matheus.ferst@eldorado.org.br>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>

target/ppc: Implement lxvkq instruction

Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Luis Pires <luis.pires@eldorado.org.br>
Signed-off-by: Matheus Ferst <matheus.ferst@eldorado.org.br>
Message-Id: <20211104123719.323713-25-matheus.ferst@eldorado.org.br>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>

target/ppc: Implement xxblendvb/xxblendvh/xxblendvw/xxblendvd instructions

Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Bruno Larsen (billionai) <bruno.larsen@eldorado.org.br>
Signed-off-by: Matheus Ferst <matheus.ferst@eldorado.org.br>
Message-Id: <20211104123719.323713-24-matheus.ferst@eldorado.org.br>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>

target/ppc: implemented XXSPLTIDP instruction

Implemented the instruction XXSPLTIDP using decodetree.

Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Bruno Larsen (billionai) <bruno.larsen@eldorado.org.br>
Signed-off-by: Matheus Ferst <matheus.ferst@eldorado.org.br>
Message-Id: <20211104123719.323713-23-matheus.ferst@eldorado.org.br>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>

target/ppc: Implemented XXSPLTIW using decodetree

Implemented the XXSPLTIW instruction, using decodetree.

Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Bruno Larsen (billionai) <bruno.larsen@eldorado.org.br>
Signed-off-by: Matheus Ferst <matheus.ferst@eldorado.org.br>
Message-Id: <20211104123719.323713-22-matheus.ferst@eldorado.org.br>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>

target/ppc: implemented XXSPLTI32DX

Implemented XXSPLTI32DX emulation using decodetree

Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Bruno Larsen (billionai) <bruno.larsen@eldorado.org.br>
Signed-off-by: Matheus Ferst <matheus.ferst@eldorado.org.br>
Message-Id: <20211104123719.323713-21-matheus.ferst@eldorado.org.br>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>

target/ppc: moved XXSPLTIB to using decodetree

Changed the function that handles XXSPLTIB emulation to using
decodetree, but still use the same logic as before

Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Bruno Larsen (billionai) <bruno.larsen@eldorado.org.br>
Signed-off-by: Matheus Ferst <matheus.ferst@eldorado.org.br>
Message-Id: <20211104123719.323713-20-matheus.ferst@eldorado.org.br>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>

target/ppc: moved XXSPLTW to using decodetree

Changed the function that handles XXSPLTW emulation to using decodetree,
but still using the same logic.

Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Bruno Larsen (billionai) <bruno.larsen@eldorado.org.br>
Signed-off-by: Matheus Ferst <matheus.ferst@eldorado.org.br>
Message-Id: <20211104123719.323713-19-matheus.ferst@eldorado.org.br>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>

target/ppc: added the instructions PLXVP and PSTXVP

Implemented the instructions plxvp and pstxvp using decodetree

Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Lucas Mateus Castro (alqotel) <lucas.castro@eldorado.org.br>
Signed-off-by: Matheus Ferst <matheus.ferst@eldorado.org.br>
Message-Id: <20211104123719.323713-18-matheus.ferst@eldorado.org.br>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>

target/ppc: added the instructions PLXV and PSTXV

Implemented the instructions plxv and pstxv using decodetree

Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Lucas Mateus Castro (alqotel) <lucas.castro@eldorado.org.br>
Signed-off-by: Matheus Ferst <matheus.ferst@eldorado.org.br>
Message-Id: <20211104123719.323713-17-matheus.ferst@eldorado.org.br>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>

target/ppc: added the instructions LXVPX and STXVPX

Implemented the instructions lxvpx and stxvpx using decodetree

Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Lucas Mateus Castro (alqotel) <lucas.castro@eldorado.org.br>
Signed-off-by: Matheus Ferst <matheus.ferst@eldorado.org.br>
Message-Id: <20211104123719.323713-16-matheus.ferst@eldorado.org.br>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>

target/ppc: added the instructions LXVP and STXVP

Implemented the instructions lxvp and stxvp using decodetree

Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Luis Pires <luis.pires@eldorado.org.br>
Signed-off-by: Lucas Mateus Castro (alqotel) <lucas.castro@eldorado.org.br>
Signed-off-by: Matheus Ferst <matheus.ferst@eldorado.org.br>
Message-Id: <20211104123719.323713-15-matheus.ferst@eldorado.org.br>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>

target/ppc: moved stxvx and lxvx from legacy to decodtree

Moved stxvx and lxvx implementation from the legacy system to
decodetree.

Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Lucas Mateus Castro (alqotel) <lucas.castro@eldorado.org.br>
Signed-off-by: Matheus Ferst <matheus.ferst@eldorado.org.br>
Message-Id: <20211104123719.323713-14-matheus.ferst@eldorado.org.br>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>

target/ppc: moved stxv and lxv from legacy to decodtree

Moved stxv and lxv implementation from the legacy system to
decodetree.

Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Luis Pires <luis.pires@eldorado.org.br>
Signed-off-by: Lucas Mateus Castro (alqotel) <lucas.castro@eldorado.org.br>
Signed-off-by: Matheus Ferst <matheus.ferst@eldorado.org.br>
Message-Id: <20211104123719.323713-13-matheus.ferst@eldorado.org.br>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>

target/ppc: receive high/low as argument in get/set_cpu_vsr

Changes get_cpu_vsr to receive a new argument indicating whether the
high or low part of the register is being accessed. This change improves
consistency between the interfaces used to access Vector and VSX
registers and helps to handle endianness in some cases.

Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Matheus Ferst <matheus.ferst@eldorado.org.br>
Message-Id: <20211104123719.323713-12-matheus.ferst@eldorado.org.br>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>

target/ppc: Introduce REQUIRE_VSX macro

Introduce the macro to centralize checking if the VSX facility is
enabled and handle it correctly.

Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Bruno Larsen (billionai) <bruno.larsen@eldorado.org.br>
Signed-off-by: Luis Pires <luis.pires@eldorado.org.br>
Signed-off-by: Matheus Ferst <matheus.ferst@eldorado.org.br>
Message-Id: <20211104123719.323713-11-matheus.ferst@eldorado.org.br>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>

target/ppc: Implement Vector Extract Double to VSR using GPR index insns

Implement the following PowerISA v3.1 instructions:
vextdubvlx: Vector Extract Double Unsigned Byte to VSR using
            GPR-specified Left-Index
vextduhvlx: Vector Extract Double Unsigned Halfword to VSR using
            GPR-specified Left-Index
vextduwvlx: Vector Extract Double Unsigned Word to VSR using
            GPR-specified Left-Index
vextddvlx: Vector Extract Double Doubleword to VSR using
           GPR-specified Left-Index
vextdubvrx: Vector Extract Double Unsigned Byte to VSR using
            GPR-specified Right-Index
vextduhvrx: Vector Extract Double Unsigned Halfword to VSR using
            GPR-specified Right-Index
vextduwvrx: Vector Extract Double Unsigned Word to VSR using
            GPR-specified Right-Index
vextddvrx: Vector Extract Double Doubleword to VSR using
           GPR-specified Right-Index

Suggested-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Luis Pires <luis.pires@eldorado.org.br>
Signed-off-by: Matheus Ferst <matheus.ferst@eldorado.org.br>
Message-Id: <20211104123719.323713-10-matheus.ferst@eldorado.org.br>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>

target/ppc: Move vinsertb/vinserth/vinsertw/vinsertd to decodetree

Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Matheus Ferst <matheus.ferst@eldorado.org.br>
Message-Id: <20211104123719.323713-9-matheus.ferst@eldorado.org.br>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>

target/ppc: Implement Vector Insert from VSR using GPR index insns

Implements the following PowerISA v3.1 instructions:
vinsbvlx: Vector Insert Byte from VSR using GPR-specified Left-Index
vinshvlx: Vector Insert Halfword from VSR using GPR-specified
          Left-Index
vinswvlx: Vector Insert Word from VSR using GPR-specified Left-Index
vinsbvrx: Vector Insert Byte from VSR using GPR-specified Right-Index
vinshvrx: Vector Insert Halfword from VSR using GPR-specified
          Right-Index
vinswvrx: Vector Insert Word from VSR using GPR-specified Right-Index

Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Matheus Ferst <matheus.ferst@eldorado.org.br>
Message-Id: <20211104123719.323713-8-matheus.ferst@eldorado.org.br>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>

target/ppc: Implement Vector Insert Word from GPR using Immediate insns

Implements the following PowerISA v3.1 instructions:
vinsw: Vector Insert Word from GPR using immediate-specified index
vinsd: Vector Insert Doubleword from GPR using immediate-specified
       index

Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Matheus Ferst <matheus.ferst@eldorado.org.br>
Message-Id: <20211104123719.323713-7-matheus.ferst@eldorado.org.br>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>

target/ppc: Implement Vector Insert from GPR using GPR index insns

Implements the following PowerISA v3.1 instructions:
vinsblx: Vector Insert Byte from GPR using GPR-specified Left-Index
vinshlx: Vector Insert Halfword from GPR using GPR-specified Left-Index
vinswlx: Vector Insert Word from GPR using GPR-specified Left-Index
vinsdlx: Vector Insert Doubleword from GPR using GPR-specified
         Left-Index
vinsbrx: Vector Insert Byte from GPR using GPR-specified Right-Index
vinshrx: Vector Insert Halfword from GPR using GPR-specified
         Right-Index
vinswrx: Vector Insert Word from GPR using GPR-specified Right-Index
vinsdrx: Vector Insert Doubleword from GPR using GPR-specified
         Right-Index

The helpers and do_vinsx receive i64 to allow code sharing with the
future implementation of Vector Insert from VSR using GPR Index.

Signed-off-by: Matheus Ferst <matheus.ferst@eldorado.org.br>
Message-Id: <20211104123719.323713-6-matheus.ferst@eldorado.org.br>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>

target/ppc: Implement vsldbi/vsrdbi instructions

Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Suggested-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Matheus Ferst <matheus.ferst@eldorado.org.br>
Message-Id: <20211104123719.323713-5-matheus.ferst@eldorado.org.br>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>

target/ppc: Implement vpdepd/vpextd instruction

pdepd and pextd helpers are moved out of #ifdef (TARGET_PPC64) to allow
them to be reused as GVecGen3.fni8.

Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Luis Pires <luis.pires@eldorado.org.br>
Signed-off-by: Matheus Ferst <matheus.ferst@eldorado.org.br>
Message-Id: <20211104123719.323713-4-matheus.ferst@eldorado.org.br>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>

target/ppc: Implement vclzdm/vctzdm instructions

The signature of do_cntzdm is changed to allow reuse as GVecGen3i.fni8.
The method is also moved out of #ifdef TARGET_PPC64, as PowerISA doesn't
say vclzdm and vctzdm are 64-bit only.

Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Luis Pires <luis.pires@eldorado.org.br>
Signed-off-by: Matheus Ferst <matheus.ferst@eldorado.org.br>
Message-Id: <20211104123719.323713-3-matheus.ferst@eldorado.org.br>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>

target/ppc: Move vcfuged to vmx-impl.c.inc

There's no reason to keep vector-impl.c.inc separate from
vmx-impl.c.inc. Additionally, let GVec handle the multiple calls to
helper_cfuged for us.

Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Matheus Ferst <matheus.ferst@eldorado.org.br>
Message-Id: <20211104123719.323713-2-matheus.ferst@eldorado.org.br>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>

ppc/pegasos2: Suppress warning when qtest enabled

Suggested-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Message-Id: <20211101151023.F0D02748F5A@zero.eik.bme.hu>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>

ppc/pnv: Fix check on block device before updating drive contents

Test is wrong and the backend can never updated. It could have led to
a QEMU crash but since the firmware deactivates flash access if a valid
layout is not detected, it went unnoticed.

Reported-by: Coverity CID 1465223
Fixes: 35dde5766211 ("ppc/pnv: Add a PNOR model")
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20211102162905.762078-1-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>

target/ppc: Move ddedpd[q],denbcd[q],dscli[q],dscri[q] to decodetree

Move the following instructions to decodetree:
ddedpd:  DFP Decode DPD To BCD
ddedpdq: DFP Decode DPD To BCD Quad
denbcd:  DFP Encode BCD To DPD
denbcdq: DFP Encode BCD To DPD Quad
dscli:   DFP Shift Significand Left Immediate
dscliq:  DFP Shift Significand Left Immediate Quad
dscri:   DFP Shift Significand Right Immediate
dscriq:  DFP Shift Significand Right Immediate Quad

Also deleted dfp-ops.c.inc, now that all PPC DFP instructions were
moved to decodetree.

Signed-off-by: Luis Pires <luis.pires@eldorado.org.br>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20211029192417.400707-16-luis.pires@eldorado.org.br>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>

target/ppc: Move dct{dp,qpq},dr{sp,dpq},dc{f,t}fix[q],dxex[q] to decodetree

Move the following instructions to decodetree:
dctdp:   DFP Convert To DFP Long
dctqpq:  DFP Convert To DFP Extended
drsp:    DFP Round To DFP Short
drdpq:   DFP Round To DFP Long
dcffix:  DFP Convert From Fixed
dcffixq: DFP Convert From Fixed Quad
dctfix:  DFP Convert To Fixed
dctfixq: DFP Convert To Fixed Quad
dxex:    DFP Extract Biased Exponent
dxexq:   DFP Extract Biased Exponent Quad

Signed-off-by: Luis Pires <luis.pires@eldorado.org.br>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20211029192417.400707-15-luis.pires@eldorado.org.br>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>

target/ppc: Move dqua[q], drrnd[q] to decodetree

Move the following instructions to decodetree:
dqua:   DFP Quantize
dquaq:  DFP Quantize Quad
drrnd:  DFP Reround
drrndq: DFP Reround Quad

Signed-off-by: Luis Pires <luis.pires@eldorado.org.br>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20211029192417.400707-14-luis.pires@eldorado.org.br>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>

target/ppc: Move dquai[q], drint{x,n}[q] to decodetree

Move the following instructions to decodetree:
dquai:   DFP Quantize Immediate
dquaiq:  DFP Quantize Immediate Quad
drintx:  DFP Round to FP Integer With Inexact
drintxq: DFP Round to FP Integer With Inexact Quad
drintn:  DFP Round to FP Integer Without Inexact
drintnq: DFP Round to FP Integer Without Inexact Quad

Signed-off-by: Luis Pires <luis.pires@eldorado.org.br>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20211029192417.400707-13-luis.pires@eldorado.org.br>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>

target/ppc: Move dcmp{u,o}[q],dts{tex,tsf,tsfi}[q] to decodetree

Move the following instructions to decodetree:
dcmpu:    DFP Compare Unordered
dcmpuq:   DFP Compare Unordered Quad
dcmpo:    DFP Compare Ordered
dcmpoq:   DFP Compare Ordered Quad
dtstex:   DFP Test Exponent
dtstexq:  DFP Test Exponent Quad
dtstsf:   DFP Test Significance
dtstsfq:  DFP Test Significance Quad
dtstsfi:  DFP Test Significance Immediate
dtstsfiq: DFP Test Significance Immediate Quad

Signed-off-by: Luis Pires <luis.pires@eldorado.org.br>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20211029192417.400707-12-luis.pires@eldorado.org.br>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>

target/ppc: Move d{add,sub,mul,div,iex}[q] to decodetree

Move the following instructions to decodetree:
dadd:  DFP Add
daddq: DFP Add Quad
dsub:  DFP Subtract
dsubq: DFP Subtract Quad
dmul:  DFP Multiply
dmulq: DFP Multiply Quad
ddiv:  DFP Divide
ddivq: DFP Divide Quad
diex:  DFP Insert Biased Exponent
diexq: DFP Insert Biased Exponent Quad

Signed-off-by: Luis Pires <luis.pires@eldorado.org.br>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20211029192417.400707-11-luis.pires@eldorado.org.br>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>

target/ppc: Move dtstdc[q]/dtstdg[q] to decodetree

Move the following instructions to decodetree:
dtstdc:  DFP Test Data Class
dtstdcq: DFP Test Data Class Quad
dtstdg:  DFP Test Data Group
dtstdgq: DFP Test Data Group Quad

Signed-off-by: Luis Pires <luis.pires@eldorado.org.br>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20211029192417.400707-10-luis.pires@eldorado.org.br>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>

target/ppc: Do not update nip on DFP instructions

Before moving the existing DFP instructions to decodetree, drop the
nip update that shouldn't be done for these instructions.

Signed-off-by: Luis Pires <luis.pires@eldorado.org.br>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20211029192417.400707-9-luis.pires@eldorado.org.br>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>

target/ppc: Implement DCTFIXQQ

Implement the following PowerISA v3.1 instruction:
dctfixqq: DFP Convert To Fixed Quadword Quad

Signed-off-by: Luis Pires <luis.pires@eldorado.org.br>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20211029192417.400707-8-luis.pires@eldorado.org.br>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>

libdecnumber: Introduce decNumberIntegralToInt128

This will be used to implement PowerPC's dctfixqq.

Signed-off-by: Luis Pires <luis.pires@eldorado.org.br>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20211029192417.400707-7-luis.pires@eldorado.org.br>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>

host-utils: Introduce mulu128

Signed-off-by: Luis Pires <luis.pires@eldorado.org.br>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20211029192417.400707-6-luis.pires@eldorado.org.br>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>

target/ppc: Implement DCFFIXQQ

Implement the following PowerISA v3.1 instruction:
dcffixqq: DFP Convert From Fixed Quadword Quad

Signed-off-by: Luis Pires <luis.pires@eldorado.org.br>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20211029192417.400707-5-luis.pires@eldorado.org.br>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>

target/ppc: Introduce REQUIRE_FPU

Signed-off-by: Fernando Valle <fernando.valle@eldorado.org.br>
Signed-off-by: Luis Pires <luis.pires@eldorado.org.br>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20211029192417.400707-4-luis.pires@eldorado.org.br>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>

target/ppc: Move REQUIRE_ALTIVEC/VECTOR to translate.c

Move REQUIRE_ALTIVEC to translate.c and rename it to REQUIRE_VECTOR.

Signed-off-by: Bruno Larsen <bruno.larsen@eldorado.org.br>
Signed-off-by: Matheus Ferst <matheus.ferst@eldorado.org.br>
Signed-off-by: Fernando Valle <fernando.valle@eldorado.org.br>
Signed-off-by: Luis Pires <luis.pires@eldorado.org.br>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Message-Id: <20211029192417.400707-3-luis.pires@eldorado.org.br>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>

libdecnumber: introduce decNumberFrom[U]Int128

This will be used to implement PowerPC's dcffixqq.

Signed-off-by: Luis Pires <luis.pires@eldorado.org.br>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20211029192417.400707-2-luis.pires@eldorado.org.br>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>

target/ppc: Implement pextd instruction

Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Matheus Ferst <matheus.ferst@eldorado.org.br>
Message-Id: <20211029202424.175401-11-matheus.ferst@eldorado.org.br>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>

target/ppc: Implement pdepd instruction

Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Matheus Ferst <matheus.ferst@eldorado.org.br>
Message-Id: <20211029202424.175401-10-matheus.ferst@eldorado.org.br>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>

target/ppc: Implement cnttzdm

Implement the following PowerISA v3.1 instruction:
cnttzdm: Count Trailing Zeros Doubleword Under Bit Mask

Suggested-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Luis Pires <luis.pires@eldorado.org.br>
Signed-off-by: Matheus Ferst <matheus.ferst@eldorado.org.br>
Message-Id: <20211029202424.175401-9-matheus.ferst@eldorado.org.br>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>

target/ppc: Implement cntlzdm

Implement the following PowerISA v3.1 instruction:
cntlzdm: Count Leading Zeros Doubleword Under Bit Mask

Suggested-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Luis Pires <luis.pires@eldorado.org.br>
Signed-off-by: Matheus Ferst <matheus.ferst@eldorado.org.br>
Message-Id: <20211029202424.175401-8-matheus.ferst@eldorado.org.br>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>

target/ppc: Implement PLQ and PSTQ

Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Matheus Ferst <matheus.ferst@eldorado.org.br>
Message-Id: <20211029202424.175401-7-matheus.ferst@eldorado.org.br>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>

target/ppc: Move LQ and STQ to decodetree

Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Matheus Ferst <matheus.ferst@eldorado.org.br>
Message-Id: <20211029202424.175401-6-matheus.ferst@eldorado.org.br>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>

target/ppc: Implement PLFS, PLFD, PSTFS and PSTFD instructions

Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Fernando Eckhardt Valle <fernando.valle@eldorado.org.br>
Signed-off-by: Matheus Ferst <matheus.ferst@eldorado.org.br>
Message-Id: <20211029202424.175401-5-matheus.ferst@eldorado.org.br>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>

target/ppc: Move load and store floating point instructions to decodetree

Move load floating point instructions (lfs, lfsu, lfsx, lfsux, lfd, lfdu, lfdx, lfdux)
and store floating point instructions(stfs, stfsu, stfsx, stfsux, stfd, stfdu, stfdx,
stfdux) from legacy system to decodetree.

Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Fernando Eckhardt Valle <fernando.valle@eldorado.org.br>
Signed-off-by: Matheus Ferst <matheus.ferst@eldorado.org.br>
Message-Id: <20211029202424.175401-4-matheus.ferst@eldorado.org.br>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>

target/ppc: move resolve_PLS_D to translate.c

Move resolve_PLS_D from fixedpoint-impl.c.inc to translate.c
because this way the function can be used not only by fixed
point instructions.

Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Fernando Eckhardt Valle <phervalle@gmail.com>
Signed-off-by: Matheus Ferst <matheus.ferst@eldorado.org.br>
Message-Id: <20211029202424.175401-3-matheus.ferst@eldorado.org.br>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>

target/ppc: introduce do_ea_calc

The do_ea_calc function will calculate the effective address(EA)
according to PowerIsa 3.1. With that, it was replaced part of
do_ldst() that calculates the EA by this new function.

Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Fernando Eckhardt Valle (pherde) <phervalle@gmail.com>
Signed-off-by: Matheus Ferst <matheus.ferst@eldorado.org.br>
Message-Id: <20211029202424.175401-2-matheus.ferst@eldorado.org.br>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>

Merge remote-tracking branch 'remotes/philmd/tags/avocado-20211108' into staging

Integration testing patches

- Rename tests/acceptance/ -> tests/avocado/
- Rename avocado_qemu.Test -> avocado_qemu.QemuSystemTest
- Introduce QemuUserTest class
- Add the first linux-user test, covering the bFLT loader

# gpg: Signature made Mon 08 Nov 2021 05:16:46 PM CET
# gpg:                using RSA key FAABE75E12917221DCFD6BB2E3E32C2CDEADC0DE
# gpg: Good signature from "Philippe Mathieu-Daudé (F4BUG) <f4bug@amsat.org>" [full]

* remotes/philmd/tags/avocado-20211108:
  tests/avocado: Remove p7zip binary availability check
  tests/avocado: Rename avocado_qemu.Test -> QemuSystemTest
  tests/avocado: Add bFLT loader linux-user test
  tests/avocado: Share useful helpers from virtiofs_submounts test
  tests/avocado: Introduce QemuUserTest base class
  tests/avocado: Make pick_default_qemu_bin() more generic
  tests/avocado: Extract QemuBaseTest from Test
  tests/acceptance: rename tests acceptance to tests avocado
  tests/acceptance: introduce new check-avocado target

Signed-off-by: Richard Henderson <richard.henderson@linaro.org>

tests/avocado: Remove p7zip binary availability check

The single use of the 7z binary has been removed in commit a30e114f3
("tests/acceptance: remove Armbian 19.11.3 test for orangepi-pc"),
we don't need to check for this binary availability anymore.

Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Joaquin de Andres <me@xcancerberox.com.ar>
Reviewed-by: Willian Rampazzo <willianr@redhat.com>
Message-Id: <20211106091059.465109-1-philmd@redhat.com>

tests/avocado: Rename avocado_qemu.Test -> QemuSystemTest

To run user-mode emulation tests, we introduced the
avocado_qemu.QemuUserTest which inherits from avocado_qemu.QemuBaseTest.
System-mode emulation tests are based on the avocado_qemu.Test class,
which also inherits avocado_qemu.QemuBaseTest. To avoid confusion,
rename it as avocado_qemu.QemuSystemTest.

Suggested-by: Wainer dos Santos Moschetta <wainersm@redhat.com>
Reviewed-by: Willian Rampazzo <willianr@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20211105143416.148332-7-f4bug@amsat.org>

tests/avocado: Add bFLT loader linux-user test

Add a very quick test that runs a busybox binary in bFLT format:

  $ AVOCADO_ALLOW_UNTRUSTED_CODE=1 \
    avocado --show=app run -t linux_user tests/avocado/load_bflt.py
  JOB ID     : db94d5960ce564c50904d666a7e259148c27e88f
  JOB LOG    : ~/avocado/job-results/job-2019-06-25T10.52-db94d59/job.log
   (1/1) tests/avocado/load_bflt.py:LoadBFLT.test_stm32: PASS (0.15 s)
  RESULTS    : PASS 1 | ERROR 0 | FAIL 0 | SKIP 0 | WARN 0 | INTERRUPT 0 | CANCEL 0
  JOB TIME   : 0.54 s

Reviewed-by: Willian Rampazzo <willianr@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20211105143416.148332-6-f4bug@amsat.org>

tests/avocado: Share useful helpers from virtiofs_submounts test

Move the useful has_cmd()/has_cmds() helpers from the virtiofs
test to the avocado_qemu public class.

Reviewed-by: Wainer dos Santos Moschetta <wainersm@redhat.com>
Reviewed-by: Willian Rampazzo <willianr@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20211105143416.148332-5-f4bug@amsat.org>

tests/avocado: Introduce QemuUserTest base class

Similarly to the 'System' Test base class with methods for testing
system emulation, the QemuUserTest class contains methods useful to
test user-mode emulation.

Reviewed-by: Wainer dos Santos Moschetta <wainersm@redhat.com>
Reviewed-by: Willian Rampazzo <willianr@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20211105143416.148332-4-f4bug@amsat.org>

tests/avocado: Make pick_default_qemu_bin() more generic

Make pick_default_qemu_bin() generic to find qemu-system or
qemu-user binaries.

Reviewed-by: Willian Rampazzo <willianr@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20211105143416.148332-3-f4bug@amsat.org>

tests/avocado: Extract QemuBaseTest from Test

The Avocado Test::fetch_asset() is handy to download artifacts
before running tests. The current class is named Test but only
tests system emulation. As we want to test user emulation,
refactor the common code as QemuBaseTest.

Reviewed-by: Willian Rampazzo <willianr@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20211105143416.148332-2-f4bug@amsat.org>