hw/arm: Add GMAC devices to NPCM7XX SoC

Change-Id: Id8a3461fb5042adc4c3fd6f4fbd1ca0d33e22565
Signed-off-by: Hao Wu <wuhaotsh@google.com>
Signed-off-by: Nabih Estefan <nabihestefan@google.com>
Reviewed-by: Tyrone Ting <kfting@nuvoton.com>
Message-id: 20240131002800.989285-3-nabihestefan@google.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>

hw/net: Add NPCMXXX GMAC device

This patch implements the basic registers of GMAC device and sets
registers for networking functionalities.
Squashed IRQ Implementation patch into this one for compliation.
Tested:
The following message shows up with the change:
Broadcom BCM54612E stmmac-0:00: attached PHY driver [Broadcom BCM54612E] (mii_bus:phy_addr=stmmac-0:00, irq=POLL)
stmmaceth f0802000.eth eth0: Link is Up - 1Gbps/Full - flow control rx/tx

Change-Id: If71c6d486b95edcccba109ba454870714d7e0940
Signed-off-by: Hao Wu <wuhaotsh@google.com>
Signed-off-by: Nabih Estefan Diaz <nabihestefan@google.com>
Reviewed-by: Tyrone Ting <kfting@nuvoton.com>
Message-id: 20240131002800.989285-2-nabihestefan@google.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>

hw/xen: convert stderr prints to error/warn reports

According to the QEMU Coding Style document:

> Do not use printf(), fprintf() or monitor_printf(). Instead, use
> error_report() or error_vreport() from error-report.h. This ensures the
> error is reported in the right place (current monitor or stderr), and in
> a uniform format.
> Use error_printf() & friends to print additional information.

This commit changes fprintfs that report warnings and errors to the
appropriate report functions.

Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Manos Pitsidianakis <manos.pitsidianakis@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Message-id: 42a8953553cf68e8bacada966f93af4fbce45919.1706544115.git.manos.pitsidianakis@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>

hw/xen/xen-hvm-common.c: convert DPRINTF to tracepoints

Tracing DPRINTFs to stderr might not be desired. A developer that relies
on tracepoints should be able to opt-in to each tracepoint and rely on
QEMU's log redirection, instead of stderr by default.

This commit converts DPRINTFs in this file that are used for tracing
into tracepoints.

Signed-off-by: Manos Pitsidianakis <manos.pitsidianakis@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Message-id: b000ab73022dfeb7a7ab0ee8fd0f41fb208adaf0.1706544115.git.manos.pitsidianakis@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>

hw/xen/xen-mapcache.c: convert DPRINTF to tracepoints

Tracing DPRINTFs to stderr might not be desired. A developer that relies
on tracepoints should be able to opt-in to each tracepoint and rely on
QEMU's log redirection, instead of stderr by default.

This commit converts DPRINTFs in this file that are used for tracing
into tracepoints.

Signed-off-by: Manos Pitsidianakis <manos.pitsidianakis@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Message-id: 2fbe1fbc59078e384761c932e97cfa4276a53d75.1706544115.git.manos.pitsidianakis@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>

hw/arm/xen_arm.c: convert DPRINTF to trace events and error/warn reports

Tracing DPRINTFs to stderr might not be desired. A developer that relies
on trace events should be able to opt-in to each trace event and rely on
QEMU's log redirection, instead of stderr by default.

This commit converts DPRINTFs in this file that are used for tracing
into trace events. Errors or warnings are converted to error_report and
warn_report calls.

Signed-off-by: Manos Pitsidianakis <manos.pitsidianakis@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Message-id: fe5e3bd54231abe933f95a24e0e88208cd8cfd8f.1706544115.git.manos.pitsidianakis@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>

hw/arm/z2: convert DPRINTF to trace events and guest errors

Tracing DPRINTFs to stderr might not be desired. A developer that relies
on trace events should be able to opt-in to each trace event and rely on
QEMU's log redirection, instead of stderr by default.

This commit converts DPRINTFs in this file that are used for tracing
into trace events. DPRINTFs that report guest errors are logged with
LOG_GUEST_ERROR.

Signed-off-by: Manos Pitsidianakis <manos.pitsidianakis@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Message-id: 799c5141c5751cf2341e1d095349612e046424a8.1706544115.git.manos.pitsidianakis@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>

hw/arm/strongarm.c: convert DPRINTF to trace events and guest errors

Tracing DPRINTFs to stderr might not be desired. A developer that relies
on trace events should be able to opt-in to each trace event and rely on
QEMU's log redirection, instead of stderr by default.

This commit converts DPRINTFs in this file that are used for tracing
into trace events. DPRINTFs that report guest errors are logged with
LOG_GUEST_ERROR.#

Signed-off-by: Manos Pitsidianakis <manos.pitsidianakis@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Message-id: 39db71dd87bf2007cf7812f3d91dde53887f1f2f.1706544115.git.manos.pitsidianakis@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>

pci-host: designware: Limit value range of iATU viewport register

The latest version of qemu (v8.2.0-869-g7a1dc45af5) crashes when booting
the mcimx7d-sabre emulation with Linux v5.11 and later.

qemu-system-arm: ../system/memory.c:2750: memory_region_set_alias_offset: Assertion `mr->alias' failed.

Problem is that the Designware PCIe emulation accepts the full value range
for the iATU Viewport Register. However, both hardware and emulation only
support four inbound and four outbound viewports.

The Linux kernel determines the number of supported viewports by writing
0xff into the viewport register and reading the value back. The expected
value when reading the register is the highest supported viewport index.
Match that code by masking the supported viewport value range when the
register is written. With this change, the Linux kernel reports

imx6q-pcie 33800000.pcie: iATU: unroll F, 4 ob, 4 ib, align 0K, limit 4G

as expected and supported.

Fixes: d64e5eabc4c7 ("pci: Add support for Designware IP block")
Cc: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: Nikita Ostrenkov <n.ostrenkov@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Message-id: 20240129060055.2616989-1-linux@roeck-us.net
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>

hw/arm/zynq: Check for CPU types in machine_run_board_init()

Leverage the common code introduced in commit c9cf636d48 ("machine:
Add a valid_cpu_types property") to check for the single valid CPU
type. Remove the now unused MachineClass::default_cpu_type field.

Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Gavin Shan <gshan@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-id: 20240129151828.59544-10-philmd@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>

hw/arm/vexpress: Check for CPU types in machine_run_board_init()

Leverage the common code introduced in commit c9cf636d48 ("machine:
Add a valid_cpu_types property") to check for the single valid CPU
type. Remove the now unused MachineClass::default_cpu_type field.

Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Gavin Shan <gshan@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-id: 20240129151828.59544-9-philmd@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>

hw/arm/npcm7xx_boards: Simplify setting MachineClass::valid_cpu_types[]

The npcm7xx Soc is created with a Cortex-A9 core, see in
hw/arm/npcm7xx.c:

  static void npcm7xx_init(Object *obj)
  {
      NPCM7xxState *s = NPCM7XX(obj);

      for (int i = 0; i < NPCM7XX_MAX_NUM_CPUS; i++) {
          object_initialize_child(obj, "cpu[*]", &s->cpu[i],
                                  ARM_CPU_TYPE_NAME("cortex-a9"));
      }

The MachineClass::default_cpu_type field is ignored: delete it.

Use the common code introduced in commit c9cf636d48 ("machine: Add
a valid_cpu_types property") to check for valid CPU type at the
board level.

Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-id: 20240129151828.59544-8-philmd@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>

hw/arm/musca: Simplify setting MachineClass::valid_cpu_types[]

Musca boards use the embedded subsystems (SSE) tied to a specific
Cortex core. Our models only use the Cortex-M33.

Use the common code introduced in commit c9cf636d48 ("machine: Add
a valid_cpu_types property") to check for valid CPU type at the
board level.

Remove the now unused MachineClass::default_cpu_type field.

Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-id: 20240129151828.59544-7-philmd@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>

hw/arm/msf2: Simplify setting MachineClass::valid_cpu_types[]

The M2Sxxx SoC family can only be used with Cortex-M3.
Propagating the CPU type from the board level is pointless.

Hard-code the CPU type at the SoC level.
Remove the now ignored MachineClass::default_cpu_type field.

Use the common code introduced in commit c9cf636d48 ("machine: Add
a valid_cpu_types property") to check for valid CPU type at the
board level.

Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-id: 20240129151828.59544-6-philmd@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>

hw/arm/highbank: Check for CPU types in machine_run_board_init()

Restrict MachineClass::valid_cpu_types[] to the single
valid CPU types.

Instead of ignoring invalid CPU type requested by the user:

  $ qemu-system-arm -M midway -cpu cortex-a7 -S -monitor stdio
  QEMU 8.2.50 monitor - type 'help' for more information
  (qemu) info qom-tree
  /machine (midway-machine)
    /cpu[0] (cortex-a15-arm-cpu)
    ...

we now display an error:

  $ qemu-system-arm -M midway -cpu cortex-a7
  qemu-system-arm: Invalid CPU model: cortex-a7
  The only valid type is: cortex-a15

Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Gavin Shan <gshan@redhat.com>
Message-id: 20240129151828.59544-5-philmd@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>

hw/arm/highbank: Add missing QOM parent for CPU cores

QDev objects created with qdev_new() need to manually add
their parent relationship with object_property_add_child().

Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Gavin Shan <gshan@redhat.com>
Message-id: 20240129151828.59544-4-philmd@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>

hw/arm/exynos: Check for CPU types in machine_run_board_init()

Restrict MachineClass::valid_cpu_types[] to the single
valid CPU type.

Instead of ignoring invalid CPU type requested by the user:

  $ qemu-system-arm -M nuri -cpu cortex-a7 -S -monitor stdio
  QEMU 8.2.50 monitor - type 'help' for more information
  (qemu) info qom-tree
  /machine (nuri-machine)
    /soc (exynos4210)
      /cpu[0] (cortex-a9-arm-cpu)
      ...

We now display an error:

  $ qemu-system-arm -M nuri -cpu cortex-a7
  qemu-system-arm: Invalid CPU model: cortex-a7
  The only valid type is: cortex-a9

Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Gavin Shan <gshan@redhat.com>
Message-id: 20240129151828.59544-3-philmd@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>

hw/arm/exynos: Add missing QOM parent for CPU cores

QDev objects created with qdev_new() need to manually add
their parent relationship with object_property_add_child().

Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Gavin Shan <gshan@redhat.com>
Message-id: 20240129151828.59544-2-philmd@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>

doc/sphinx/hxtool.py: add optional label argument to SRST directive

We can't just embed labels directly into files like qemu-options.hx which
are included from multiple top-level rST files, because Sphinx sees the
labels as duplicate: https://github.com/sphinx-doc/sphinx/issues/9707

So add an optional argument to the SRST directive which causes a label
of the form '.. _DOCNAME-HXFILE-LABEL:' to be emitted, where 'DOCNAME'
is the name of the top level rST file, 'HXFILE' is the filename of the
.hx file, and 'LABEL' is the text provided within the 'SRST()' directive.
Using the DOCNAME of the top-level rST document means that it is unique
even when the .hx file is included from two different documents, as is
the case for qemu-options.hx

Now where the Xen PV documentation refers to the documentation for the
-initrd command line option, it can emit a link directly to it as
'<system/invocation-qemu-options-initrd>'.

Signed-off-by: David Woodhouse <dwmw@amazon.co.uk>
Reviewed-by: Paul Durrant <paul@xen.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20240130190348.682912-1-dwmw2@infradead.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>

target/arm: Reinstate "vfp" property on AArch32 CPUs

In commit 4315f7c614743 we restructured the logic for creating the
VFP related properties to avoid testing the aa32_simd_r32 feature on
AArch64 CPUs.  However in the process we accidentally stopped
exposing the "vfp" QOM property on AArch32 TCG CPUs.

This mostly hasn't had any ill effects because not many people want
to disable VFP, but it wasn't intentional.  Reinstate the property.

Cc: qemu-stable@nongnu.org
Fixes: 4315f7c614743 ("target/arm: Restructure has_vfp_d32 test")
Resolves: https://gitlab.com/qemu-project/qemu/-/issues/2098
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20240126193432.2210558-1-peter.maydell@linaro.org

tests/qtest/xlnx-versal-trng-test.c: Drop use of variable length array

This test program is the last use of any variable length array in the
codebase.  If we can get rid of all uses of VLAs we can make the
compiler error on new additions.  This is a defensive measure against
security bugs where an on-stack dynamic allocation isn't correctly
size-checked (e.g.  CVE-2021-3527).

In this case the test code didn't even want a variable-sized
array, it was just accidentally using syntax that gave it one.
(The array size for C has to be an actual constant expression,
not just something that happens to be known to be constant...)

Remove the VLA usage.

Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Zhao Liu <zhao1.liu@intel.com>
Message-id: 20240125173211.1786196-2-peter.maydell@linaro.org

target/arm: Add ID_AA64ZFR0_EL1.B16B16 to the exposed-to-userspace set

In kernel commit 5d5b4e8c2d9ec ("arm64/sve: Report FEAT_SVE_B16B16 to
userspace") Linux added ID_AA64ZFR0_el1.B16B16 to the set of ID
register fields which it exposes to userspace.  Update our
exported_bits mask to include this.

(This doesn't yet change any behaviour for us, because we don't yet
have any CPUs that implement this feature, which is part of SVE2.)

Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20240125134304.1470404-1-peter.maydell@linaro.org

qemu-options.hx: Improve -serial option documentation

The -serial option documentation is a bit brief about '-serial none'
and '-serial null'. In particular it's not very clear about the
difference between them, and it doesn't mention that it's up to
the machine model whether '-serial none' means "don't create the
serial port" or "don't wire the serial port up to anything".

Expand on these points.

Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-id: 20240122163607.459769-3-peter.maydell@linaro.org

system/vl.c: Fix handling of '-serial none -serial something'

Currently if the user passes multiple -serial options on the command
line, we mostly treat those as applying to the different serial
devices in order, so that for example
 -serial stdio -serial file:filename
will connect the first serial port to stdio and the second to the
named file.

The exception to this is the '-serial none' serial device type.  This
means "don't allocate this serial device", but a bug means that
following -serial options are not correctly handled, so that
 -serial none -serial stdio
has the unexpected effect that stdio is connected to the first serial
port, not the second.

This is a very long-standing bug that dates back at least as far as
commit 998bbd74b9d81 from 2009.

Make the 'none' serial type move forward in the indexing of serial
devices like all the other serial types, so that any subsequent
-serial options are correctly handled.

Note that if your commandline mistakenly had a '-serial none' that
was being overridden by a following '-serial something' option, you
should delete the unnecessary '-serial none'.  This will give you the
same behaviour as before, on QEMU versions both with and without this
bug fix.

Cc: qemu-stable@nongnu.org
Reported-by: Bohdan Kostiv <bohdan.kostiv@tii.ae>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20240122163607.459769-2-peter.maydell@linaro.org
Fixes: 998bbd74b9d81 ("default devices: core code & serial lines")
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>

hw/core: Remove transitional infrastructure from BusClass

BusClass currently has transitional infrastructure to support
subclasses which implement the legacy BusClass::reset method rather
than the Resettable interface.  We have now removed all the users of
BusClass::reset in the tree, so we can remove the transitional
infrastructure.

Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Cédric Le Goater <clg@redhat.com>
Acked-by: Maciej S. Szmigiero <maciej.szmigiero@oracle.com>
Tested-by: Cédric Le Goater <clg@redhat.com>
Reviewed-by: Zhao Liu <zhao1.liu@intel.com>
Message-id: 20240119163512.3810301-6-peter.maydell@linaro.org

hw/s390x/css-bridge: switch virtual-css bus to 3-phase-reset

Switch the s390x virtual-css bus from using BusClass::reset to the
Resettable interface.

This has no behavioural change, because the BusClass code to support
subclasses that use the legacy BusClass::reset will call that method
in the hold phase of 3-phase reset.

Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Cédric Le Goater <clg@redhat.com>
Acked-by: Maciej S. Szmigiero <maciej.szmigiero@oracle.com>
Tested-by: Cédric Le Goater <clg@redhat.com>
Reviewed-by: Halil Pasic <pasic@linux.ibm.com>
Reviewed-by: Eric Farman <farman@linux.ibm.com>
Reviewed-by: Zhao Liu <zhao1.liu@intel.com>
Message-id: 20240119163512.3810301-5-peter.maydell@linaro.org

adb: Switch bus reset to 3-phase-reset

Switch the ADB bus from using BusClass::reset to the Resettable
interface.

This has no behavioural change, because the BusClass code to support
subclasses that use the legacy BusClass::reset will call that method
in the hold phase of 3-phase reset.

Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Cédric Le Goater <clg@redhat.com>
Acked-by: Maciej S. Szmigiero <maciej.szmigiero@oracle.com>
Tested-by: Cédric Le Goater <clg@redhat.com>
Reviewed-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Zhao Liu <zhao1.liu@intel.com>
Message-id: 20240119163512.3810301-4-peter.maydell@linaro.org

vmbus: Switch bus reset to 3-phase-reset

Switch vmbus from using BusClass::reset to the Resettable interface.

This has no behavioural change, because the BusClass code to support
subclasses that use the legacy BusClass::reset will call that method
in the hold phase of 3-phase reset.

Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Cédric Le Goater <clg@redhat.com>
Acked-by: Maciej S. Szmigiero <maciej.szmigiero@oracle.com>
Tested-by: Cédric Le Goater <clg@redhat.com>
Reviewed-by: Zhao Liu <zhao1.liu@intel.com>
Message-id: 20240119163512.3810301-3-peter.maydell@linaro.org

pci: Switch bus reset to 3-phase-reset

Switch the PCI bus from using BusClass::reset to the Resettable
interface.

This has no behavioural change, because the BusClass code to support
subclasses that use the legacy BusClass::reset will call that method
in the hold phase of 3-phase reset.

Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Cédric Le Goater <clg@redhat.com>
Tested-by: Cédric Le Goater <clg@redhat.com>
Reviewed-by: Zhao Liu <zhao1.liu@intel.com>
Message-id: 20240119163512.3810301-2-peter.maydell@linaro.org

target/arm: fix exception syndrome for AArch32 bkpt insn

Debug exceptions that target AArch32 Hyp mode are reported differently
than on AAarch64. Internally, Qemu uses the AArch64 syndromes. Therefore
such exceptions need to be either converted to a prefetch abort
(breakpoints, vector catch) or a data abort (watchpoints).

Cc: qemu-stable@nongnu.org
Signed-off-by: Jan Klötzke <jan.kloetzke@kernkonzept.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20240127202758.3326381-1-jan.kloetzke@kernkonzept.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>

Merge tag 'pull-aspeed-20240201' of https://github.com/legoater/qemu into staging

aspeed queue:

* Update of buildroot images to 2023.11 (6.6.3 kernel)
* Check of the valid CPU type supported by aspeed machines
* Simplified models for the IBM's FSI bus and the Aspeed
  controller bridge

# -----BEGIN PGP SIGNATURE-----
#
# iQIzBAABCAAdFiEEoPZlSPBIlev+awtgUaNDx8/77KEFAmW7Sa8ACgkQUaNDx8/7
# 7KG7mw/8DbMJY6aqgq5YANszzem1ktJphPCNxq081cbczCOUpCNX4aL+0/ANvxxD
# lbJQB+SZeIRmuFbxYPhq68rtzB4vG7tsQpns4H33EPKT4vuzF70lq4fgptMiun3q
# 1ZJ2LF3jonvQWdhbC17wzAQz0FFb4F7XOxz++UL4okPsgzsYItnd+TWs8q7+erRb
# 84UwN+eBTBAl/FiNk679/tBTqAfCVGgQ7dzotr4f3tg5POvrGOrlEjAn0O+dGGDj
# wgILmpEBsTsilRB1tz8Kw0j/v/VkHz1DJu45lRAV9CIrN22iKcjMilNGgNDT8kcI
# yAlxAw3iN+hVFqDov8wFPjDYd/Qw2oRAPy2Kd14hW9xL8zBOTms1JK5L0PS2+Feo
# ZjMJ2cOJq3t4Wt1ZXRhgHfF4ANwP0OZ/y9bHCy3CkBljEeiTQbikHP9gVV4qHXZH
# 4Q0HnDZQwAgobw3CmZ8jVx1dQueqy3ycuvkhCyv3S0l/tdbtXDtr5pNNu3dAP/PJ
# 3nifLdRImhDvxxO9GKaCdUVLzELzMJl0GrgAsVJPKVnKHA4IiVKmB+XcW9IUbfy/
# 3zA2wHJLrEF+MF6MsuNcEYCCqUvyNLm7rUrXk1wNLXpCJ35bbW5IYy7Ty/8E2GHb
# D5Cv/EPNhMBiNA4+HqQlMOTC13Ozv2qwCuWYCh2Ik8mnzaEiyTo=
# =0C5S
# -----END PGP SIGNATURE-----
# gpg: Signature made Thu 01 Feb 2024 07:35:11 GMT
# gpg:                using RSA key A0F66548F04895EBFE6B0B6051A343C7CFFBECA1
# gpg: Good signature from "Cédric Le Goater <clg@kaod.org>" [undefined]
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg:          There is no indication that the signature belongs to the owner.
# Primary key fingerprint: A0F6 6548 F048 95EB FE6B  0B60 51A3 43C7 CFFB ECA1

* tag 'pull-aspeed-20240201' of https://github.com/legoater/qemu:
  hw/fsi: Update MAINTAINER list
  hw/fsi: Added FSI documentation
  hw/fsi: Added qtest
  hw/arm: Hook up FSI module in AST2600
  hw/fsi: Aspeed APB2OPB & On-chip peripheral bus
  hw/fsi: Introduce IBM's FSI master
  hw/fsi: Introduce IBM's cfam
  hw/fsi: Introduce IBM's fsi-slave model
  hw/fsi: Introduce IBM's FSI Bus
  hw/fsi: Introduce IBM's scratchpad device
  hw/fsi: Introduce IBM's Local bus
  hw/arm/aspeed: Check for CPU types in machine_run_board_init()
  hw/arm/aspeed: Introduce aspeed_soc_cpu_type() helper
  hw/arm/aspeed: Init CPU defaults in a common helper
  hw/arm/aspeed: Set default CPU count using aspeed_soc_num_cpus()
  hw/arm/aspeed: Remove dead code
  tests/avocado/machine_aspeed.py: Update buildroot images to 2023.11

Signed-off-by: Peter Maydell <peter.maydell@linaro.org>

Merge tag 'pull-loongarch-20240201' of https://gitlab.com/gaosong/qemu into staging

pull-loongarch-20240201

# -----BEGIN PGP SIGNATURE-----
#
# iLMEAAEKAB0WIQS4/x2g0v3LLaCcbCxAov/yOSY+3wUCZbtI0AAKCRBAov/yOSY+
# 35J4A/9ehl15MIrkByqq8QNQnG4PbKWOTcTev6P0sEAhzPUtBpcGPesoHnt+DFuk
# f3WluWsfnFY9pCRgB9VBSpy89O6Efj187bpekT/PD5svPOXoUmETafv1p2vsVrpj
# huMNijt7I/LAXUCb2gA5pnNH9vrrJ8E5kQlgmYfh35cEhHObMQ==
# =Q9Gn
# -----END PGP SIGNATURE-----
# gpg: Signature made Thu 01 Feb 2024 07:31:28 GMT
# gpg:                using RSA key B8FF1DA0D2FDCB2DA09C6C2C40A2FFF239263EDF
# gpg: Good signature from "Song Gao <m17746591750@163.com>" [unknown]
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg:          There is no indication that the signature belongs to the owner.
# Primary key fingerprint: B8FF 1DA0 D2FD CB2D A09C  6C2C 40A2 FFF2 3926 3EDF

* tag 'pull-loongarch-20240201' of https://gitlab.com/gaosong/qemu:
  target/loongarch: Fix qtest test-hmp error when KVM-only build

Signed-off-by: Peter Maydell <peter.maydell@linaro.org>

hw/fsi: Update MAINTAINER list

Add maintainer for IBM FSI model

Signed-off-by: Ninad Palsule <ninad@linux.ibm.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
[ clg: - slight change in commit log
       - fixed file list ]
Signed-off-by: Cédric Le Goater <clg@kaod.org>

hw/fsi: Added FSI documentation

Documentation for IBM FSI model.

Signed-off-by: Ninad Palsule <ninad@linux.ibm.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
[ clg : - Removed source file list
        - Fixed aspeed machine reference ]
Signed-off-by: Cédric Le Goater <clg@kaod.org>

hw/fsi: Added qtest

Added basic qtests for FSI model.

Signed-off-by: Ninad Palsule <ninad@linux.ibm.com>
Acked-by: Thomas Huth <thuth@redhat.com>
[ clg: aspeed-fsi-test.c -> aspeed_fsi-test.c to match other filenames ]
Signed-off-by: Cédric Le Goater <clg@kaod.org>

hw/arm: Hook up FSI module in AST2600

This patchset introduces IBM's Flexible Service Interface(FSI).

Time for some fun with inter-processor buses. FSI allows a service
processor access to the internal buses of a host POWER processor to
perform configuration or debugging.

FSI has long existed in POWER processes and so comes with some baggage,
including how it has been integrated into the ASPEED SoC.

Working backwards from the POWER processor, the fundamental pieces of
interest for the implementation are:

1. The Common FRU Access Macro (CFAM), an address space containing
   various "engines" that drive accesses on buses internal and external
   to the POWER chip. Examples include the SBEFIFO and I2C masters. The
   engines hang off of an internal Local Bus (LBUS) which is described
   by the CFAM configuration block.

2. The FSI slave: The slave is the terminal point of the FSI bus for
   FSI symbols addressed to it. Slaves can be cascaded off of one
   another. The slave's configuration registers appear in address space
   of the CFAM to which it is attached.

3. The FSI master: A controller in the platform service processor (e.g.
   BMC) driving CFAM engine accesses into the POWER chip. At the
   hardware level FSI is a bit-based protocol supporting synchronous and
   DMA-driven accesses of engines in a CFAM.

4. The On-Chip Peripheral Bus (OPB): A low-speed bus typically found in
   POWER processors. This now makes an appearance in the ASPEED SoC due
   to tight integration of the FSI master IP with the OPB, mainly the
   existence of an MMIO-mapping of the CFAM address straight onto a
   sub-region of the OPB address space.

5. An APB-to-OPB bridge enabling access to the OPB from the ARM core in
   the AST2600. Hardware limitations prevent the OPB from being directly
   mapped into APB, so all accesses are indirect through the bridge.

The implementation appears as following in the qemu device tree:

    (qemu) info qtree
    bus: main-system-bus
      type System
      ...
      dev: aspeed.apb2opb, id ""
        gpio-out "sysbus-irq" 1
        mmio 000000001e79b000/0000000000001000
        bus: opb.1
          type opb
          dev: fsi.master, id ""
            bus: fsi.bus.1
              type fsi.bus
              dev: cfam.config, id ""
              dev: cfam, id ""
                bus: fsi.lbus.1
                  type lbus
                  dev: scratchpad, id ""
                    address = 0 (0x0)
        bus: opb.0
          type opb
          dev: fsi.master, id ""
            bus: fsi.bus.0
              type fsi.bus
              dev: cfam.config, id ""
              dev: cfam, id ""
                bus: fsi.lbus.0
                  type lbus
                  dev: scratchpad, id ""
                    address = 0 (0x0)

The LBUS is modelled to maintain the qdev bus hierarchy and to take
advantage of the object model to automatically generate the CFAM
configuration block. The configuration block presents engines in the
order they are attached to the CFAM's LBUS. Engine implementations
should subclass the LBusDevice and set the 'config' member of
LBusDeviceClass to match the engine's type.

CFAM designs offer a lot of flexibility, for instance it is possible for
a CFAM to be simultaneously driven from multiple FSI links. The modeling
is not so complete; it's assumed that each CFAM is attached to a single
FSI slave (as a consequence the CFAM subclasses the FSI slave).

As for FSI, its symbols and wire-protocol are not modelled at all. This
is not necessary to get FSI off the ground thanks to the mapping of the
CFAM address space onto the OPB address space - the models follow this
directly and map the CFAM memory region into the OPB's memory region.
Future work includes supporting more advanced accesses that drive the
FSI master directly rather than indirectly via the CFAM mapping, which
will require implementing the FSI state machine and methods for each of
the FSI symbols on the slave. Further down the track we can also look at
supporting the bitbanged SoftFSI drivers in Linux by extending the FSI
slave model to resolve sequences of GPIO IRQs into FSI symbols, and
calling the associated symbol method on the slave to map the access onto
the CFAM.

Testing:
    Tested by reading cfam config address 0 on rainier machine type.

    root@p10bmc:~# pdbg -a getcfam 0x0
    p0: 0x0 = 0xc0022d15

Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Ninad Palsule <ninad@linux.ibm.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>

hw/fsi: Aspeed APB2OPB & On-chip peripheral bus

This is a part of patchset where IBM's Flexible Service Interface is
introduced.

An APB-to-OPB bridge enabling access to the OPB from the ARM core in
the AST2600. Hardware limitations prevent the OPB from being directly
mapped into APB, so all accesses are indirect through the bridge.

The On-Chip Peripheral Bus (OPB): A low-speed bus typically found in
POWER processors. This now makes an appearance in the ASPEED SoC due
to tight integration of the FSI master IP with the OPB, mainly the
existence of an MMIO-mapping of the CFAM address straight onto a
sub-region of the OPB address space.

Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Ninad Palsule <ninad@linux.ibm.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
[ clg: - moved FSIMasterState under AspeedAPB2OPBState
       - modified fsi_opb_fsi_master_address() and
         fsi_opb_opb2fsi_address()
       - instroduced fsi_aspeed_apb2opb_init()
       - reworked fsi_aspeed_apb2opb_realize()
       - removed FSIMasterState object and fsi_opb_realize()
       - simplified OPBus
       - introduced fsi_aspeed_apb2opb_rw to fix endianness issue ]
Signed-off-by: Cédric Le Goater <clg@kaod.org>

target/loongarch: Fix qtest test-hmp error when KVM-only build

The cc->sysemu_ops->get_phys_page_debug() is NULL when
KVM-only build. this patch fixes it.

Signed-off-by: Song Gao <gaosong@loongson.cn>
Tested-by: Bibo Mao <maobibo@loongson.cn>
Message-Id: <20240125061401.52526-1-gaosong@loongson.cn>

hw/fsi: Introduce IBM's FSI master

This is a part of patchset where IBM's Flexible Service Interface is
introduced.

This commit models the FSI master. CFAM is hanging out of FSI master which is a bus controller.

The FSI master: A controller in the platform service processor (e.g.
BMC) driving CFAM engine accesses into the POWER chip. At the
hardware level FSI is a bit-based protocol supporting synchronous and
DMA-driven accesses of engines in a CFAM.

Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Ninad Palsule <ninad@linux.ibm.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
[ clg: - move FSICFAMState object under FSIMasterState
       - introduced fsi_master_init()
       - reworked fsi_master_realize()
       - dropped FSIBus definition ]
Signed-off-by: Cédric Le Goater <clg@kaod.org>

hw/fsi: Introduce IBM's cfam

This is a part of patchset where IBM's Flexible Service Interface is
introduced.

The Common FRU Access Macro (CFAM), an address space containing
various "engines" that drive accesses on busses internal and external
to the POWER chip. Examples include the SBEFIFO and I2C masters. The
engines hang off of an internal Local Bus (LBUS) which is described
by the CFAM configuration block.

Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Ninad Palsule <ninad@linux.ibm.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
[ clg: - moved object FSIScratchPad under FSICFAMState
       - moved FSIScratchPad code under cfam.c
       - introduced fsi_cfam_instance_init()
       - reworked fsi_cfam_realize() ]
Signed-off-by: Cédric Le Goater <clg@kaod.org>

hw/fsi: Introduce IBM's fsi-slave model

This is a part of patchset where IBM's Flexible Service Interface is
introduced.

The FSI slave: The slave is the terminal point of the FSI bus for
FSI symbols addressed to it. Slaves can be cascaded off of one
another. The slave's configuration registers appear in address space
of the CFAM to which it is attached.

Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Ninad Palsule <ninad@linux.ibm.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>

hw/fsi: Introduce IBM's FSI Bus

This is a part of patchset where FSI bus is introduced.

The FSI bus is a simple bus where FSI master is attached.

Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Ninad Palsule <ninad@linux.ibm.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
[ clg: - removed include/hw/fsi/engine-scratchpad.h and
         hw/fsi/engine-scratchpad.c
       - dropped FSI_SCRATCHPAD
       - included FSIBus definition
       - dropped hw/fsi/trace-events changes ]
Signed-off-by: Cédric Le Goater <clg@kaod.org>

hw/fsi: Introduce IBM's scratchpad device

This is a part of patchset where IBM's Flexible Service Interface is
introduced.

The scratchpad provides a set of non-functional registers. The firmware
is free to use them, hardware does not support any special management
support. The scratchpad registers can be read or written from LBUS
slave. The scratch pad is managed under FSI CFAM state.

Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Ninad Palsule <ninad@linux.ibm.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
[ clg: - moved object FSIScratchPad under FSICFAMState
       - moved FSIScratchPad code under cfam.c ]
Signed-off-by: Cédric Le Goater <clg@kaod.org>

hw/fsi: Introduce IBM's Local bus

This is a part of patchset where IBM's Flexible Service Interface is
introduced.

The LBUS is modelled to maintain mapped memory for the devices. The
memory is mapped after CFAM config, peek table and FSI slave registers.

Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Ninad Palsule <ninad@linux.ibm.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
[ clg: - removed lbus_add_device() bc unused
       - removed lbus_create_device() bc used only once
       - removed "address" property
       - updated meson.build to build fsi dir
       - included an empty hw/fsi/trace-events ]
Signed-off-by: Cédric Le Goater <clg@kaod.org>

hw/arm/aspeed: Check for CPU types in machine_run_board_init()

Aspeed SoCs use a single CPU type (set as AspeedSoCClass::cpu_type).
Convert it to a NULL-terminated array (of a single non-NULL element).

Set MachineClass::valid_cpu_types[] to use the common machine code
to provide hints when the requested CPU is invalid (see commit
e702cbc19e ("machine: Improve is_cpu_type_supported()").

Reviewed-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Gavin Shan <gshan@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>

hw/arm/aspeed: Introduce aspeed_soc_cpu_type() helper

In order to alter AspeedSoCClass::cpu_type in the next
commit, introduce the aspeed_soc_cpu_type() helper to
retrieve the per-SoC CPU type from AspeedSoCClass.

Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Gavin Shan <gshan@redhat.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>

hw/arm/aspeed: Init CPU defaults in a common helper

Rework aspeed_soc_num_cpus() as a new init_cpus_defaults()
helper to reduce code duplication.

Reviewed-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Gavin Shan <gshan@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>

hw/arm/aspeed: Set default CPU count using aspeed_soc_num_cpus()

Since commit b7f1a0cb76 ("arm/aspeed: Compute the number
of CPUs from the SoC definition") Aspeed machines use the
aspeed_soc_num_cpus() helper to set the number of CPUs.

Use it for the ast1030-evb (commit 356b230ed1 "aspeed/soc:
Add AST1030 support") and supermicrox11-bmc (commit 40a38df55e
"hw/arm/aspeed: Add board model for Supermicro X11 BMC") machines.

Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Gavin Shan <gshan@redhat.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>

hw/arm/aspeed: Remove dead code

Remove copy/paste typo from commit 6c323aba40 ("hw/arm/aspeed:
Adding new machine Tiogapass in QEMU").

Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Gavin Shan <gshan@redhat.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>

tests/avocado/machine_aspeed.py: Update buildroot images to 2023.11

Compared to mainline buildroot, these images have some customization :

- Linux version is bumped to 6.6.3 and built with a custom config
- U-Boot is switched to the one provided by OpenBMC for more support
- defconfigs extra tools for dev

See branch [1] for more details.

There are a few changes since last update, commit ed1f5ff84209. Images
all have a password now and I2C devices have been updated in the Linux
ast2600-evb device tree [2]. Do the necessary adjustements.

[1] https://github.com/legoater/buildroot/commits/aspeed-2023.11
[2] https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/commit/?id=9deb10cf160e

Signed-off-by: Cédric Le Goater <clg@kaod.org>

Merge tag 'pull-trivial-patches' of https://gitlab.com/mjt0k/qemu into staging

trivial patches for 2024-01-31

# -----BEGIN PGP SIGNATURE-----
#
# iQFDBAABCAAtFiEEe3O61ovnosKJMUsicBtPaxppPlkFAmW6NScPHG1qdEB0bHMu
# bXNrLnJ1AAoJEHAbT2saaT5ZdQYH/2fhfhZotH0V2qAcMxlOoHbAE9UhZNRsSYtf
# QFP0GXFYFAMm7LHkPUbvKgO7LylKWAOMn/zKZqgj1Vf1EpoKQ2FwLtR/buDz86Ec
# pi2OrDPRA7Ay5c3ow3YZZkUOhQTTcR5rNjYctPtt/J4j8ol/z5vre7weJIg2bCJe
# zI7vIVg7iFFzbkXY20KHngJ5nDC+aEm7WaGlxAP8kfkvy324Wy9O2k8qu2J5zbLT
# HGvh3rwEDvRTYe4CaKFFHWNV0m4092HAr/dJBobugI5VZ6QQpK6Tgy8N+4ZrCHD2
# SjUKeym85VTOYGuY8b18fk5MQK2SzsfBUJ4x8VGC75W4mJ8agdc=
# =HImO
# -----END PGP SIGNATURE-----
# gpg: Signature made Wed 31 Jan 2024 11:55:19 GMT
# gpg:                using RSA key 7B73BAD68BE7A2C289314B22701B4F6B1A693E59
# gpg:                issuer "mjt@tls.msk.ru"
# gpg: Good signature from "Michael Tokarev <mjt@tls.msk.ru>" [full]
# gpg:                 aka "Michael Tokarev <mjt@corpit.ru>" [full]
# gpg:                 aka "Michael Tokarev <mjt@debian.org>" [full]
# Primary key fingerprint: 6EE1 95D1 886E 8FFB 810D  4324 457C E0A0 8044 65C5
#      Subkey fingerprint: 7B73 BAD6 8BE7 A2C2 8931  4B22 701B 4F6B 1A69 3E59

* tag 'pull-trivial-patches' of https://gitlab.com/mjt0k/qemu: (21 commits)
  hw/hyperv: Include missing headers
  hw/intc/xics: Include missing 'cpu.h' header
  hw/arm: Add `\n` to hint message
  hw/loongarch: Add `\n` to hint message
  hw/i386: Add `\n` to hint message
  backends/hostmem: Fix block comments style (checkpatch.pl warnings)
  misc: Clean up includes
  riscv: Clean up includes
  cxl: Clean up includes
  include: Clean up includes
  m68k: Clean up includes
  acpi: Clean up includes
  aspeed: Clean up includes
  disas/riscv: Clean up includes
  hyperv: Clean up includes
  scripts/clean-includes: Update exclude list
  mailmap: Fix Stefan Weil email
  qemu-docs: Update options for graphical frontends
  qapi/migration.json: Fix the member name for MigrationCapability
  colo: examples: remove mentions of script= and (wrong) downscript=
  ...

Signed-off-by: Peter Maydell <peter.maydell@linaro.org>

Merge tag 'block-pull-request' of https://gitlab.com/stefanha/qemu into staging

Pull request

# -----BEGIN PGP SIGNATURE-----
#
# iQEzBAABCAAdFiEEhpWov9P5fNqsNXdanKSrs4Grc8gFAmW5b1IACgkQnKSrs4Gr
# c8geoQf8DU8Z8jlvy1luuBZLq3R7hnC7c3Wzje0atLGP++pX6QUXfAgGDsTTIQeh
# XWmkFhbOBurhToH8YpgPyNG8ZWYd9+NIvLnIJiWDklNDZg2zC00aOi8yBEbsgyFb
# 50HJA30AAHq8PuctCzhGhENLxvBvNDNME74SwYH7FSIK5x/nA1XBHDZsjst1/Hk2
# 1loLbVWElbU28Xll7hI862SAb8RULC/sRQomkQAhpydxq4TApNuRwvpRfPNFwFJ0
# +dCquCJEfV6wfD62xg2CBGA5DrD9T7ADxmCYl4DQyp3HIRKXAptjgLsx3aZaIr1z
# KAnCRNUXRuLgRZf7b9I+HhxGISoNng==
# =/bBL
# -----END PGP SIGNATURE-----
# gpg: Signature made Tue 30 Jan 2024 21:51:14 GMT
# gpg:                using RSA key 8695A8BFD3F97CDAAC35775A9CA4ABB381AB73C8
# gpg: Good signature from "Stefan Hajnoczi <stefanha@redhat.com>" [full]
# gpg:                 aka "Stefan Hajnoczi <stefanha@gmail.com>" [full]
# Primary key fingerprint: 8695 A8BF D3F9 7CDA AC35  775A 9CA4 ABB3 81AB 73C8

* tag 'block-pull-request' of https://gitlab.com/stefanha/qemu:
  hw/block/block.c: improve confusing blk_check_size_and_read_all() error
  hw/core/qdev.c: add qdev_get_human_name()
  pflash: fix sectors vs bytes confusion in blk_pread_nonzeroes()
  block/blkio: Make s->mem_region_alignment be 64 bits
  block/io_uring: improve error message when init fails

Signed-off-by: Peter Maydell <peter.maydell@linaro.org>

hw/block/block.c: improve confusing blk_check_size_and_read_all() error

In cases where a device tries to read more bytes than the block device
contains, the error is vague: "device requires X bytes, block backend
provides Y bytes".

This patch changes the errors of this function to include the block
backend name, the device id and device type name where appropriate.

Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Manos Pitsidianakis <manos.pitsidianakis@linaro.org>
Message-id: 7260eadff22c08457740117c1bb7bd2b4353acb9.1706598705.git.manos.pitsidianakis@linaro.org
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>

hw/core/qdev.c: add qdev_get_human_name()

Add a simple method to return some kind of human readable identifier for
use in error messages.

Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Manos Pitsidianakis <manos.pitsidianakis@linaro.org>
Message-id: 8b566bfced98ae44be1fcc1f8e7215f0c3393aa1.1706598705.git.manos.pitsidianakis@linaro.org
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>

pflash: fix sectors vs bytes confusion in blk_pread_nonzeroes()

The following expression is incorrect because blk_pread_nonzeroes()
deals in units of bytes, not sectors:

  bytes = MIN(size - offset, BDRV_REQUEST_MAX_SECTORS)
                                              ^^^^^^^

BDRV_REQUEST_MAX_BYTES is the appropriate constant.

Fixes: a4b15a8b9ef2 ("pflash: Only read non-zero parts of backend image")
Cc: Xiang Zheng <zhengxiang9@huawei.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-id: 20240130002712.257815-1-stefanha@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>

block/blkio: Make s->mem_region_alignment be 64 bits

With GCC 14 the code failed to compile on i686 (and was wrong for any
version of GCC):

../block/blkio.c: In function ‘blkio_file_open’:
../block/blkio.c:857:28: error: passing argument 3 of ‘blkio_get_uint64’ from incompatible pointer type [-Wincompatible-pointer-types]
  857 |                            &s->mem_region_alignment);
      |                            ^~~~~~~~~~~~~~~~~~~~~~~~
      |                            |
      |                            size_t * {aka unsigned int *}
In file included from ../block/blkio.c:12:
/usr/include/blkio.h:49:67: note: expected ‘uint64_t *’ {aka ‘long long unsigned int *’} but argument is of type ‘size_t *’ {aka ‘unsigned int *’}
   49 | int blkio_get_uint64(struct blkio *b, const char *name, uint64_t *value);
      |                                                         ~~~~~~~~~~^~~~~

Signed-off-by: Richard W.M. Jones <rjones@redhat.com>
Message-id: 20240130122006.2977938-1-rjones@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>

block/io_uring: improve error message when init fails

The man page for io_uring_queue_init states:

> io_uring_queue_init(3) returns 0 on success and -errno on failure.

and the man page for io_uring_setup (which is one of the functions
where the return value of io_uring_queue_init() can come from) states:

> On error, a negative error code is returned. The caller should not
> rely on errno variable.

Tested using 'sysctl kernel.io_uring_disabled=2'. Output before this
change:

> failed to init linux io_uring ring

Output after this change:

> failed to init linux io_uring ring: Operation not permitted

Signed-off-by: Fiona Ebner <f.ebner@proxmox.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-ID: <20240123135044.204985-1-f.ebner@proxmox.com>

hw/hyperv: Include missing headers

Include missing headers in order to avoid when refactoring
unrelated headers:

  hw/hyperv/hyperv.c:33:18: error: field ‘msg_page_mr’ has incomplete type
    33 |     MemoryRegion msg_page_mr;
       |                  ^~~~~~~~~~~
  hw/hyperv/hyperv.c: In function ‘synic_update’:
  hw/hyperv/hyperv.c:64:13: error: implicit declaration of function ‘memory_region_del_subregion’ [-Werror=implicit-function-declaration]
    64 |             memory_region_del_subregion(get_system_memory(),
       |             ^~~~~~~~~~~~~~~~~~~~~~~~~~~
  hw/hyperv/hyperv.c: In function ‘hyperv_hcall_signal_event’:
  hw/hyperv/hyperv.c:683:17: error: implicit declaration of function ‘ldq_phys’; did you mean ‘ldub_phys’? [-Werror=implicit-function-declaration]
   683 |         param = ldq_phys(&address_space_memory, addr);
       |                 ^~~~~~~~
       |                 ldub_phys
  hw/hyperv/hyperv.c:683:17: error: nested extern declaration of ‘ldq_phys’ [-Werror=nested-externs]
  hw/hyperv/hyperv.c: In function ‘hyperv_hcall_retreive_dbg_data’:
  hw/hyperv/hyperv.c:792:24: error: ‘TARGET_PAGE_SIZE’ undeclared (first use in this function); did you mean ‘TARGET_PAGE_BITS’?
   792 |     msg.u.recv.count = TARGET_PAGE_SIZE - sizeof(*debug_data_out);
       |                        ^~~~~~~~~~~~~~~~
       |                        TARGET_PAGE_BITS
  hw/hyperv/hyperv.c: In function ‘hyperv_syndbg_send’:
  hw/hyperv/hyperv.c:885:16: error: ‘HV_SYNDBG_STATUS_INVALID’ undeclared (first use in this function)
   885 |         return HV_SYNDBG_STATUS_INVALID;
       |                ^~~~~~~~~~~~~~~~~~~~~~~~

Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Manos Pitsidianakis <manos.pitsidianakis@linaro.org>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>

hw/intc/xics: Include missing 'cpu.h' header

Include missing headers in order to avoid when refactoring
unrelated headers:

  hw/intc/xics.c: In function 'icp_realize':
  hw/intc/xics.c:304:5: error: unknown type name 'PowerPCCPU'
    304 |     PowerPCCPU *cpu;
        |     ^~~~~~~~~~

Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>

hw/arm: Add `\n` to hint message

error_printf() doesn't add newlines.

Signed-off-by: Greg Kurz <groug@kaod.org>
Reviewed-by: Ani Sinha <anisinha@redhat.com>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>

hw/loongarch: Add `\n` to hint message

error_printf() doesn't add newlines.

Signed-off-by: Greg Kurz <groug@kaod.org>
Reviewed-by: Ani Sinha <anisinha@redhat.com>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>

hw/i386: Add `\n` to hint message

error_printf() doesn't add newlines.

Signed-off-by: Greg Kurz <groug@kaod.org>
Reviewed-by: Ani Sinha <anisinha@redhat.com>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>

backends/hostmem: Fix block comments style (checkpatch.pl warnings)

While re-indenting code in host_memory_backend_memory_complete(),
we triggered various "Block comments use a leading /* on a separate
line" warnings from checkpatch.pl. Correct the comments style.

Fixes: e199f7ad4d ("backends: Simplify host_memory_backend_memory_complete()")
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Xiaoyao Li <xiaoyao.li@intel.com>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>

misc: Clean up includes

This commit was created with scripts/clean-includes:
 ./scripts/clean-includes --git misc net/af-xdp.c plugins/*.c audio/pwaudio.c util/userfaultfd.c

All .c should include qemu/osdep.h first.  The script performs three
related cleanups:

* Ensure .c files include qemu/osdep.h first.
* Including it in a .h is redundant, since the .c  already includes
  it.  Drop such inclusions.
* Likewise, including headers qemu/osdep.h includes is redundant.
  Drop these, too.

Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Zhao Liu <zhao1.liu@intel.com>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>

riscv: Clean up includes

This commit was created with scripts/clean-includes:
 ./scripts/clean-includes --git riscv target/riscv/*.[ch]

All .c should include qemu/osdep.h first.  The script performs three
related cleanups:

* Ensure .c files include qemu/osdep.h first.
* Including it in a .h is redundant, since the .c  already includes
  it.  Drop such inclusions.
* Likewise, including headers qemu/osdep.h includes is redundant.
  Drop these, too.

Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Zhao Liu <zhao1.liu@intel.com>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>

cxl: Clean up includes

This commit was created with scripts/clean-includes.

All .c should include qemu/osdep.h first.  The script performs three
related cleanups:

* Ensure .c files include qemu/osdep.h first.
* Including it in a .h is redundant, since the .c  already includes
  it.  Drop such inclusions.
* Likewise, including headers qemu/osdep.h includes is redundant.
  Drop these, too.

Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Zhao Liu <zhao1.liu@intel.com>
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>

include: Clean up includes

This commit was created with scripts/clean-includes:
 ./scripts/clean-includes --git include include/*/*.h include/*/*/*.h

All .c should include qemu/osdep.h first.  The script performs three
related cleanups:

* Ensure .c files include qemu/osdep.h first.
* Including it in a .h is redundant, since the .c  already includes
  it.  Drop such inclusions.
* Likewise, including headers qemu/osdep.h includes is redundant.
  Drop these, too.

Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Zhao Liu <zhao1.liu@intel.com>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>

m68k: Clean up includes

This commit was created with scripts/clean-includes:
./scripts/clean-includes --git m68k include/hw/audio/asc.h include/hw/m68k/*.h

All .c should include qemu/osdep.h first.  The script performs three
related cleanups:

* Ensure .c files include qemu/osdep.h first.
* Including it in a .h is redundant, since the .c  already includes
  it.  Drop such inclusions.
* Likewise, including headers qemu/osdep.h includes is redundant.
  Drop these, too.

Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Zhao Liu <zhao1.liu@intel.com>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>

acpi: Clean up includes

This commit was created with scripts/clean-includes:
 ./scripts/clean-includes --git acpi include/hw/*/*acpi.h hw/*/*acpi.c

All .c should include qemu/osdep.h first.  The script performs three
related cleanups:

* Ensure .c files include qemu/osdep.h first.
* Including it in a .h is redundant, since the .c  already includes
  it.  Drop such inclusions.
* Likewise, including headers qemu/osdep.h includes is redundant.
  Drop these, too.

Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Zhao Liu <zhao1.liu@intel.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>

aspeed: Clean up includes

This commit was created with scripts/clean-includes.

All .c should include qemu/osdep.h first.  The script performs three
related cleanups:

* Ensure .c files include qemu/osdep.h first.
* Including it in a .h is redundant, since the .c  already includes
  it.  Drop such inclusions.
* Likewise, including headers qemu/osdep.h includes is redundant.
  Drop these, too.

Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Zhao Liu <zhao1.liu@intel.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>

disas/riscv: Clean up includes

This commit was created with scripts/clean-includes:
 ./scripts/clean-includes --git disas/riscv disas/riscv*[ch]

All .c should include qemu/osdep.h first.  The script performs three
related cleanups:

* Ensure .c files include qemu/osdep.h first.
* Including it in a .h is redundant, since the .c  already includes
  it.  Drop such inclusions.
* Likewise, including headers qemu/osdep.h includes is redundant.
  Drop these, too.

Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Zhao Liu <zhao1.liu@intel.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>

hyperv: Clean up includes

This commit was created with scripts/clean-includes:
 ./scripts/clean-includes --git hyperv hw/hyperv/*.[ch]

All .c should include qemu/osdep.h first.  The script performs three
related cleanups:

* Ensure .c files include qemu/osdep.h first.
* Including it in a .h is redundant, since the .c  already includes
  it.  Drop such inclusions.
* Likewise, including headers qemu/osdep.h includes is redundant.
  Drop these, too.

Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Zhao Liu <zhao1.liu@intel.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>

scripts/clean-includes: Update exclude list

Update the exclude list to exclude some more files which don't follow our
standard #include policy.

Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>

mailmap: Fix Stefan Weil email

Commit 5204b499a6 ("mailmap: Fix Stefan Weil author email")
corrected authorship for patch received at qemu-devel@nongnu.org,
correct now for patch received at qemu-trivial@nongnu.org.

Update other authorship email for Stefan's commits.

Suggested-by: Stefan Weil <sw@weilnetz.de>
Fixes: d819fc9516 ("virtio-blk: Fix potential nullptr read access")
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>

qemu-docs: Update options for graphical frontends

The command line options `-ctrl-grab` and `-alt-grab` have been removed
in QEMU 7.1. Instead, use the `-display sdl,grab-mod=<modifiers>` option
to specify the grab modifiers.

Resolves: https://gitlab.com/qemu-project/qemu/-/issues/2103
Signed-off-by: Yihuan Pan <xun794@gmail.com>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>

qapi/migration.json: Fix the member name for MigrationCapability

s/@compression/@compress/

Fixes: 864128df46
Signed-off-by: Han Han <hhan@redhat.com>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>

colo: examples: remove mentions of script= and (wrong) downscript=

There's no need to repeat script=/etc/qemu-ifup in examples,
as it is already in there.  More, all examples uses incorrect
"down script=" (which should be "downscript=").

Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Reviewed-by: Zhang Chen <chen.zhang@intel.com>

dump: Fix HMP dump-guest-memory -z without -R

-z without -R has no effect: the dump format remains @elf.  Fix the
logic error so it becomes @kdump-zlib.

Fixes: e6549197f7ed (dump: Add command interface for kdump-raw formats)
Fixes: CID 1523841
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Stephen Brennan <stephen.s.brennan@oracle.com>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>

Merge tag 'qga-pull-2024-01-30' of https://github.com/kostyanf14/qemu into staging

qga-pull-2024-01-30

# -----BEGIN PGP SIGNATURE-----
#
# iQIzBAABCAAdFiEEwsLBCepDxjwUI+uE711egWG6hOcFAmW409sACgkQ711egWG6
# hOc0PxAAj0Lhgt70OpAGQd5ERBgdRbh2/pJkKvdWBZvUAkVyFEp6Wn1UEC9aRpdi
# g8KCfYWVpp4LKMm5Ok1/8MKzAKT0jJFKatX0iZy/sx5M0A7x2/cJWgTv69L41Ld3
# FoJM/a/te8VUSk/jPKMqf4G7BzqYyHDnAlcnLjnvUsUabnocjmpSSckCNWLtQ/Sz
# RCGOwaTJ4HKW9O7yuw4gcXeYf2G21UemkITLh7Kdv/6fqqlg3k2gRSQeQ11Xh9Tc
# Jst7511vs+9AvDVM67o84z6UQwlp+23IJb3PBG2Td+Odr7BDAturWE4yyqPtjcpf
# Kcy6uMO6ZNYSW9CAspIF271fObLBPdvvMCHabar8x3LwF/6SxdnVRnWbqVsY/LSZ
# j76VB7TashwxzgqXEqmSrJmCSiCU4L7k8+KU0XxqIg4howlHzoRlejuMZzVK8Hyt
# Cu5tqa6yq8+twxzP4qQhkvazGgYgWo/xNaZ8D3h6xxxZ4NE/hN24YodtyFV/NGWE
# VSvUpzTKettECcyPo3OGezOqcr0vW5Z776MQOsMQWAjwm3bjM8hMzuKglnJe7Lt4
# DAbreHQ5s+pELQnq/cv7AVAr3zy2AIpPq4xDPJUHunAh+kMFY3cHCNaKytiRqmf+
# kZtd4nSN9j5+0oE5jSiuPn9C96y3shGL95XR6WW0nN1ImWOVgx4=
# =Tl7c
# -----END PGP SIGNATURE-----
# gpg: Signature made Tue 30 Jan 2024 10:47:55 GMT
# gpg:                using RSA key C2C2C109EA43C63C1423EB84EF5D5E8161BA84E7
# gpg: Good signature from "Kostiantyn Kostiuk (Upstream PR sign) <kkostiuk@redhat.com>" [unknown]
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg:          There is no indication that the signature belongs to the owner.
# Primary key fingerprint: C2C2 C109 EA43 C63C 1423  EB84 EF5D 5E81 61BA 84E7

* tag 'qga-pull-2024-01-30' of https://github.com/kostyanf14/qemu:
  qga: Solaris has net/if_arp.h and netinet/if_ether.h but not ETHER_ADDR_LEN
  qga-win: Fix guest-get-fsinfo multi-disks collection
  tests/unit/test-qga: do not qualify executable paths
  guest-agent: improve help for --allow-rpcs and --block-rpcs

Signed-off-by: Peter Maydell <peter.maydell@linaro.org>

Merge tag 'pull-tcg-20240130' of https://gitlab.com/rth7680/qemu into staging

linux-user: Allow gdbstub to ignore page protection
cpu-exec: simplify jump cache management
include/exec: Cleanups toward building accel/tcg once

# -----BEGIN PGP SIGNATURE-----
#
# iQFRBAABCgA7FiEEekgeeIaLTbaoWgXAZN846K9+IV8FAmW4LXcdHHJpY2hhcmQu
# aGVuZGVyc29uQGxpbmFyby5vcmcACgkQZN846K9+IV+CgAf8CdqkvKsUK9/5bu99
# 9E4kRBkR8KqWYvBfRs4IFmjoEdEa4sCujWrHliOcW7Kh+XlVyAPI9rZG32QkxCEQ
# hi9WXieXjfPLTTmrbeiq7cwxztSj8Z55wwvbxkrtFyGDQ0AMccp49tAvfejEb6VD
# Ssx96nWQDgryLrn+My+wMQjl9aVKUWp5vB8k12aAcpRXPH2yoGE2JHAZ1C743nA6
# rShiJAT78HwERcMXDeYmmriYg0s4Z4+A6ErTiXDnFgj87YanHZc0I/55G5Sh+pW8
# REicD3jwS0GHOOHL0K781FopE1wTM442GLVxobXoxUXsHEiO+3TK5JdEIqvSstYA
# fRB8Pg==
# =xZOe
# -----END PGP SIGNATURE-----
# gpg: Signature made Mon 29 Jan 2024 22:57:59 GMT
# gpg:                using RSA key 7A481E78868B4DB6A85A05C064DF38E8AF7E215F
# gpg:                issuer "richard.henderson@linaro.org"
# gpg: Good signature from "Richard Henderson <richard.henderson@linaro.org>" [full]
# Primary key fingerprint: 7A48 1E78 868B 4DB6 A85A  05C0 64DF 38E8 AF7E 215F

* tag 'pull-tcg-20240130' of https://gitlab.com/rth7680/qemu: (31 commits)
  target/i386: Extract x86_cpu_exec_halt() from accel/tcg/
  accel/tcg: Introduce TCGCPUOps::cpu_exec_halt() handler
  accel/tcg: Inline need_replay_interrupt
  target/i386: Extract x86_need_replay_interrupt() from accel/tcg/
  accel/tcg: Introduce TCGCPUOps::need_replay_interrupt() handler
  accel/tcg: Use CPUState.cc instead of CPU_GET_CLASS in cpu-exec.c
  target/loongarch: Constify loongarch_tcg_ops
  include/qemu: Add TCGCPUOps typedef to typedefs.h
  accel/tcg: Un-inline icount_exit_request() for clarity
  accel/tcg: Rename tcg_cpus_exec() -> tcg_cpu_exec()
  accel/tcg: Rename tcg_cpus_destroy() -> tcg_cpu_destroy()
  accel/tcg: Rename tcg_ss[] -> tcg_specific_ss[] in meson
  accel/tcg: Move perf and debuginfo support to tcg/
  accel/tcg: Remove #ifdef TARGET_I386 from perf.c
  tcg: Make tb_cflags() usable from target-agnostic code
  accel/tcg: Make use of qemu_target_page_mask() in perf.c
  target: Make qemu_target_page_mask() available for *-user
  accel/tcg/cpu-exec: Use RCU_READ_LOCK_GUARD
  tests/tcg: Add the PROT_NONE gdbstub test
  tests/tcg: Factor out gdbstub test functions
  ...

Signed-off-by: Peter Maydell <peter.maydell@linaro.org>

qga: Solaris has net/if_arp.h and netinet/if_ether.h but not ETHER_ADDR_LEN

Solaris has net/if_arp.h and netinet/if_ether.h rather than net/ethernet.h,
but does not define ETHER_ADDR_LEN, instead providing ETHERADDRL.

Signed-off-by: Nick Briggs <nicholas.h.briggs@gmail.com>
Reviewed-by: Konstantin Kostiuk <kkostiuk@redhat.com>
Signed-off-by: Konstantin Kostiuk <kkostiuk@redhat.com>

qga-win: Fix guest-get-fsinfo multi-disks collection

When a volume has more than one disk, all disks cannot be
returned correctly because there is not enough malloced memory
for disk extents, so before executing DeviceIoControl for the
second time, get the correct size of the required memory space
to store all disk extents.

Details:
https://learn.microsoft.com/en-us/windows/win32/api/winioctl/ns-winioctl-volume_disk_extents

Signed-off-by: Peng Ji <peng.ji@smartx.com>
Reviewed-by: Konstantin Kostiuk <kkostiuk@redhat.com>
Signed-off-by: Konstantin Kostiuk <kkostiuk@redhat.com>

tests/unit/test-qga: do not qualify executable paths

guest-exec invocation does not need the full path of the executable to
execute. Using only the command names ensures correct execution of the
test on systems not adhering to the FHS.

Signed-off-by: Samuel Tardieu <sam@rfc1149.net>
Reviewed-by: Konstantin Kostiuk <kkostiuk@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: "Daniel P. Berrangé" <berrange@redhat.com>
Signed-off-by: Konstantin Kostiuk <kkostiuk@redhat.com>

guest-agent: improve help for --allow-rpcs and --block-rpcs

Resolves: https://gitlab.com/qemu-project/qemu/-/issues/1757

Updates to qga help output and documentation for --allow-rpcs and --blocks-rpcs

Signed-off-by: "Angel M. Villegas" <anvilleg@cisco.com>
Reviewed-by: Konstantin Kostiuk <kkostiuk@redhat.com>
Signed-off-by: Konstantin Kostiuk <kkostiuk@redhat.com>

target/i386: Extract x86_cpu_exec_halt() from accel/tcg/

Move this x86-specific code out of the generic accel/tcg/.

Reported-by: Anton Johansson <anjo@rev.ng>
Reviewed-by: Anton Johansson <anjo@rev.ng>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20240124101639.30056-10-philmd@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>

accel/tcg: Introduce TCGCPUOps::cpu_exec_halt() handler

In order to make accel/tcg/ target agnostic,
introduce the cpu_exec_halt() handler.

Reviewed-by: Anton Johansson <anjo@rev.ng>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20240124101639.30056-9-philmd@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>

accel/tcg: Inline need_replay_interrupt

The function is now trivial, and with inlining we can
re-use the calling function's tcg_ops variable.

Signed-off-by: Richard Henderson <richard.henderson@linaro.org>

target/i386: Extract x86_need_replay_interrupt() from accel/tcg/

Move this x86-specific code out of the generic accel/tcg/.

Reviewed-by: Anton Johansson <anjo@rev.ng>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Pavel Dovgalyuk <Pavel.Dovgalyuk@ispras.ru>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20240124101639.30056-8-philmd@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>

accel/tcg: Introduce TCGCPUOps::need_replay_interrupt() handler

In order to make accel/tcg/ target agnostic,
introduce the need_replay_interrupt() handler.

Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Anton Johansson <anjo@rev.ng>
Reviewed-by: Pavel Dovgalyuk <Pavel.Dovgalyuk@ispras.ru>
Message-Id: <20240124101639.30056-7-philmd@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>

accel/tcg: Use CPUState.cc instead of CPU_GET_CLASS in cpu-exec.c

CPU_GET_CLASS does runtime type checking; use the cached
copy of the class instead.

Signed-off-by: Richard Henderson <richard.henderson@linaro.org>

target/loongarch: Constify loongarch_tcg_ops

Signed-off-by: Richard Henderson <richard.henderson@linaro.org>

include/qemu: Add TCGCPUOps typedef to typedefs.h

QEMU coding style recommends using structure typedefs.

Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>

accel/tcg: Un-inline icount_exit_request() for clarity

Convert packed logic to dumb icount_exit_request() helper.
No functional change intended.

Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Anton Johansson <anjo@rev.ng>
Message-Id: <20240124101639.30056-5-philmd@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>

accel/tcg: Rename tcg_cpus_exec() -> tcg_cpu_exec()

tcg_cpus_exec() operates on a single vCPU, rename it
as 'tcg_cpu_exec'.

Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Anton Johansson <anjo@rev.ng>
Message-Id: <20240124101639.30056-4-philmd@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>

accel/tcg: Rename tcg_cpus_destroy() -> tcg_cpu_destroy()

tcg_cpus_destroy() operates on a single vCPU, rename it
as 'tcg_cpu_destroy'.

Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Anton Johansson <anjo@rev.ng>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20240124101639.30056-3-philmd@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>

accel/tcg: Rename tcg_ss[] -> tcg_specific_ss[] in meson

tcg_ss[] source set contains target-specific units.
Rename it as 'tcg_specific_ss[]' for clarity.

Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Anton Johansson <anjo@rev.ng>
Message-Id: <20240124101639.30056-2-philmd@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>

accel/tcg: Move perf and debuginfo support to tcg/

tcg/ should not depend on accel/tcg/, but perf and debuginfo
support provided by the latter are being used by tcg/tcg.c.

Since that's the only user, move both to tcg/.

Suggested-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Ilya Leoshkevich <iii@linux.ibm.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-ID: <20231212003837.64090-5-iii@linux.ibm.com>
Message-Id: <20240125054631.78867-5-philmd@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>

accel/tcg: Remove #ifdef TARGET_I386 from perf.c

Preparation for moving perf.c to tcg/.

This affects only profiling guest code, which has code in a non-0 based
segment, e.g., 16-bit code, which is not particularly important.

Suggested-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Ilya Leoshkevich <iii@linux.ibm.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-ID: <20231212003837.64090-4-iii@linux.ibm.com>
Message-Id: <20240125054631.78867-4-philmd@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>

tcg: Make tb_cflags() usable from target-agnostic code

Currently tb_cflags() is defined in exec-all.h, which is not usable
from target-agnostic code. Move it to translation-block.h, which is.

Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Ilya Leoshkevich <iii@linux.ibm.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-ID: <20231212003837.64090-3-iii@linux.ibm.com>
Message-Id: <20240125054631.78867-3-philmd@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>

accel/tcg: Make use of qemu_target_page_mask() in perf.c

Stop using TARGET_PAGE_MASK in order to make perf.c more
target-agnostic.

Signed-off-by: Ilya Leoshkevich <iii@linux.ibm.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-ID: <20231212003837.64090-2-iii@linux.ibm.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20240125054631.78867-2-philmd@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>