As the comment of pci_get_domain_bus_and_slot() says, it
returns a PCI device with refcount incremented, when finish
using it, the caller must decrement the reference count by
calling pci_dev_put().
In ixgbe_get_first_secondary_devfn() and ixgbe_x550em_a_has_mii(),
pci_dev_put() is called to avoid leak.
Fixes: 8fa10ef01260 ("ixgbe: register a mdiobus") Signed-off-by: Yang Yingliang <yangyingliang@huawei.com> Tested-by: Gurucharan G <gurucharanx.g@intel.com> (A Contingent worker at Intel) Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On some SoCs (hello SM6115) vcca-supply is not wired to any smd-rpm
or rpmh regulator, but instead powered by the VDD_MX line, which is
voted for in the DSI ctrl node.
On some SoCs (hello SM6350) vdds-supply is not wired to any smd-rpm
or rpmh regulator, but instead powered by the VDD_MX/mx.lvl line,
which is voted for in the DSI ctrl node.
There are 3 possible interrupt sources are handled by DP controller,
HPDstatus, Controller state changes and Aux read/write transaction.
At every irq, DP controller have to check isr status of every interrupt
sources and service the interrupt if its isr status bits shows interrupts
are pending. There is potential race condition may happen at current aux
isr handler implementation since it is always complete dp_aux_cmd_fifo_tx()
even irq is not for aux read or write transaction. This may cause aux read
transaction return premature if host aux data read is in the middle of
waiting for sink to complete transferring data to host while irq happen.
This will cause host's receiving buffer contains unexpected data. This
patch fixes this problem by checking aux isr and return immediately at
aux isr handler if there are no any isr status bits set.
Current there is a bug report regrading eDP edid corruption happen during
system booting up. After lengthy debugging to found that VIDEO_READY
interrupt was continuously firing during system booting up which cause
dp_aux_isr() to complete dp_aux_cmd_fifo_tx() prematurely to retrieve data
from aux hardware buffer which is not yet contains complete data transfer
from sink. This cause edid corruption.
Follows are the signature at kernel logs when problem happen,
EDID has corrupt header
panel-simple-dp-aux aux-aea0000.edp: Couldn't identify panel via EDID
Changes in v2:
-- do complete if (ret == IRQ_HANDLED) ay dp-aux_isr()
-- add more commit text
Changes in v3:
-- add Stephen suggested
-- dp_aux_isr() return IRQ_XXX back to caller
-- dp_ctrl_isr() return IRQ_XXX back to caller
Changes in v4:
-- split into two patches
Changes in v5:
-- delete empty line between tags
Changes in v6:
-- remove extra "that" and fixed line more than 75 char at commit text
The Lenovo Legion 5 15ARH05 needs ideapad-laptop to call SALS_FNLOCK_ON /
SALS_FNLOCK_OFF on Fn-lock state change to get the LED in the Fn key to
correctly reflect the Fn-lock state.
Add a DMI match for the Legion 5 15ARH05 to the set_fn_lock_led_list[]
table for this.
Fixes: 81a5603a0f50 ("platform/x86: ideapad-laptop: Fix interrupt storm on fn-lock toggle on some Yoga laptops") Signed-off-by: Hans de Goede <hdegoede@redhat.com> Link: https://lore.kernel.org/r/20221215154357.123876-1-hdegoede@redhat.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It is possible for the DSI controller to be active when MDP is
power collapsed. DSI controller needs to have it's own vote for
mdss gdsc to ensure that gdsc remains on in such cases."
This however doesn't appear to be the case for the apq8064 so we shouldn't
be marking power-domain as required in yaml checks.
So far the adreno quirks have all been assigned with an OR operator,
which is problematic, because they were assigned consecutive integer
values, which makes checking them with an AND operator kind of no bueno..
Switch to using BIT(n) so that only the quirks that the programmer chose
are taken into account when evaluating info->quirks & ADRENO_QUIRK_...
Fixes: 370063ee427a ("drm/msm/adreno: Add A540 support") Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> Reviewed-by: Marijn Suijten <marijn.suijten@somainline.org> Reviewed-by: Rob Clark <robdclark@gmail.com> Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org> Reviewed-by: Akhil P Oommen <quic_akhilpo@quicinc.com>
Patchwork: https://patchwork.freedesktop.org/patch/516456/ Link: https://lore.kernel.org/r/20230102100201.77286-1-konrad.dybcio@linaro.org Signed-off-by: Rob Clark <robdclark@chromium.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use KE_VSW instead of KE_SW for the SW_CAMERA_LENS_COVER key_entry
and get the value of the switch from the status field when handling
SW_CAMERA_LENS_COVER events, instead of always reporting 0.
Also correctly set the initial SW_CAMERA_LENS_COVER value.
Fixes: 8af9fa37b8a3 ("platform/x86: dell-privacy: Add support for Dell hardware privacy") Signed-off-by: Hans de Goede <hdegoede@redhat.com> Link: https://lore.kernel.org/r/20221221220724.119594-1-hdegoede@redhat.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It is possible that we (the host/kernel driver) receive command messages
that are not intended for us. Ignore those for now.
The whole story is a bit more complicated: It is possible to enable
debug output on SAM, which is sent via SSH command messages. By default
this output is sent to a debug connector, with its own target ID
(TID=0x03). It is possible to override the target of the debug output
and set it to the host/kernel driver. This, however, does not change the
original target ID of the message. Meaning, we receive messages with
TID=0x03 (debug) but expect to only receive messages with TID=0x00
(host).
The problem is that the different target ID also comes with a different
scope of request IDs. In particular, these do not follow the standard
event rules (i.e. do not fall into a set of small reserved values).
Therefore, current message handling interprets them as responses to
pending requests and tries to match them up via the request ID. However,
these debug output messages are not in fact responses, and therefore
this will at best fail to find the request and at worst pass on the
wrong data as response for a request.
Therefore ignore any command messages not intended for us (host) for
now. We can implement support for the debug messages once we have a
better understanding of them.
Note that this may also provide a bit more stability and avoid some
driver confusion in case any other targets want to talk to us in the
future, since we don't yet know what to do with those as well. A warning
for the dropped messages should suffice for now and also give us a
chance of discovering new targets if they come along without any
potential for bugs/instabilities.
Fixes: c167b9c7e3d6 ("platform/surface: Add Surface Aggregator subsystem") Signed-off-by: Maximilian Luz <luzmaximilian@gmail.com> Link: https://lore.kernel.org/r/20221202223327.690880-2-luzmaximilian@gmail.com Reviewed-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Unlike keys where userspace only reacts to keypresses, userspace may act
on switches in both (0 and 1) of their positions.
For example if a SW_TABLET_MODE switch is registered then GNOME will not
automatically show the onscreen keyboard when a text field gets focus on
touchscreen devices when SW_TABLET_MODE reports 0 and when SW_TABLET_MODE
reports 1 libinput will block (filter out) builtin keyboard and touchpad
events.
So to avoid unwanted side-effects EV_SW type inputs should only be
registered if they are actually present, only register SW_CAMERA_LENS_COVER
if it is actually there.
Fixes: 8af9fa37b8a3 ("platform/x86: dell-privacy: Add support for Dell hardware privacy") Signed-off-by: Hans de Goede <hdegoede@redhat.com> Link: https://lore.kernel.org/r/20221221220724.119594-2-hdegoede@redhat.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If smb311 posix is enabled, we send the intended mode for file
creation in the posix create context. Instead of using what's there on
the stack, create the mfsymlink file with 0644.
Fixes: ce558b0e17f8a ("smb3: Add posix create context for smb3.11 posix mounts") Cc: stable@vger.kernel.org Signed-off-by: Volker Lendecke <vl@samba.org> Reviewed-by: Tom Talpey <tom@talpey.com> Reviewed-by: Paulo Alcantara (SUSE) <pc@cjr.nz> Signed-off-by: Steve French <stfrench@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
After applying an engine reset, on some platforms like Jasperlake, we
occasionally detect that the engine state is not cleared until shortly
after the resume. As we try to resume the engine with volatile internal
state, the first request fails with a spurious CS event (it looks like
it reports a lite-restore to the hung context, instead of the expected
idle->active context switch).
Userspace can guess the handle value and try to race GEM object creation
with handle close, resulting in a use-after-free if we dereference the
object after dropping the handle's reference. For that reason, dropping
the handle's reference must be done *after* we are done dereferencing
the object.
Make sure that *ptr__ within arch_this_cpu_to_op_simple() is only
dereferenced once by using READ_ONCE(). Otherwise the compiler could
generate incorrect code.
The current cmpxchg_double() loops within the perf hw sampling code do not
have READ_ONCE() semantics to read the old value from memory. This allows
the compiler to generate code which reads the "old" value several times
from memory, which again allows for inconsistencies.
The compiler could generate code where te->flags used within the
cmpxchg_double() call may be refetched from memory and which is not
necessarily identical to the previous read version which was used to
generate te_flags. Which in turn means that an incorrect update could
happen.
Fix this by adding READ_ONCE() semantics to all cmpxchg_double()
loops. Given that READ_ONCE() cannot generate code on s390 which atomically
reads 16 bytes, use a private compare-and-swap-double implementation to
achieve that.
Also replace cmpxchg_double() with the private implementation to be able to
re-use the old value within the loops.
As a side effect this converts the whole code to only use bit fields
to read and modify bits within the hws trailer header.
Reported-by: Alexander Gordeev <agordeev@linux.ibm.com> Acked-by: Alexander Gordeev <agordeev@linux.ibm.com> Acked-by: Hendrik Brueckner <brueckner@linux.ibm.com> Reviewed-by: Thomas Richter <tmricht@linux.ibm.com> Cc: <stable@vger.kernel.org> Link: https://lore.kernel.org/linux-s390/Y71QJBhNTIatvxUT@osiris/T/#ma14e2a5f7aa8ed4b94b6f9576799b3ad9c60f333 Signed-off-by: Heiko Carstens <hca@linux.ibm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
These indices should reference the ID placed within the dai_driver
array, not the indices of the array itself.
This fixes commit 4ff028f6c108 ("ASoC: qcom: lpass-cpu: Make I2S SD
lines configurable"), which among others, broke IPQ8064 audio
(sound/soc/qcom/lpass-ipq806x.c) because it uses ID 4 but we'd stop
initializing the mi2s_playback_sd_mode and mi2s_capture_sd_mode arrays
at ID 0.
Fixes: 4ff028f6c108 ("ASoC: qcom: lpass-cpu: Make I2S SD lines configurable") Cc: <stable@vger.kernel.org> Signed-off-by: Brian Norris <computersforpeace@gmail.com> Reviewed-by: Stephan Gerhold <stephan@gerhold.net> Link: https://lore.kernel.org/r/20221231061545.2110253-1-computersforpeace@gmail.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This commit addresses the following erroneous situation with file-based
kdump executed on a system with a valid IPL report.
On s390, a kdump kernel, its initrd and IPL report if present are loaded
into a special and reserved on boot memory region - crashkernel. When
a system crashes and kdump was activated before, the purgatory code
is entered first which swaps the crashkernel and [0 - crashkernel size]
memory regions. Only after that the kdump kernel is entered. For this
reason, the pointer to an IPL report in lowcore must point to the IPL report
after the swap and not to the address of the IPL report that was located in
crashkernel memory region before the swap. Failing to do so, makes the
kdump's decompressor try to read memory from the crashkernel memory region
which already contains the production's kernel memory.
The situation described above caused spontaneous kdump failures/hangs
on systems where the Secure IPL is activated because on such systems
an IPL report is always present. In that case kdump's decompressor tried
to parse an IPL report which frequently lead to illegal memory accesses
because an IPL report contains addresses to various data.
Cc: <stable@vger.kernel.org> Fixes: 99feaa717e55 ("s390/kexec_file: Create ipl report and pass to next kernel") Reviewed-by: Vasily Gorbik <gor@linux.ibm.com> Signed-off-by: Alexander Egorenkov <egorenar@linux.ibm.com> Signed-off-by: Heiko Carstens <hca@linux.ibm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
$ gcc -Wall -Wextra -o test file1.c file2.c
$ perf record -e intel_pt//u --filter 'filter func @ ./test' -- ./test
Multiple symbols with name 'func'
#1 0x1149 l func
which is near main
#2 0x1179 l func
which is near other
Disambiguate symbol name by inserting #n after the name e.g. func #2
Or select a global symbol by inserting #0 or #g or #G
Failed to parse address filter: 'filter func @ ./test'
Filter format is: filter|start|stop|tracestop <start symbol or address> [/ <end symbol or size>] [@<file name>]
Where multiple filters are separated by space or comma.
$ perf record -e intel_pt//u --filter 'filter func #2 @ ./test' -- ./test
Failed to parse address filter: 'filter func #2 @ ./test'
Filter format is: filter|start|stop|tracestop <start symbol or address> [/ <end symbol or size>] [@<file name>]
Where multiple filters are separated by space or comma.
Add timeout polling wait for auxiliary timestamps snapshot FIFO clear bit
(ATSFC) to clear. This is to ensure no residue fifo value is being read
erroneously.
Fixes: f4da56529da6 ("net: stmmac: Add support for external trigger timestamping") Cc: <stable@vger.kernel.org> # 5.10.x Signed-off-by: Noor Azura Ahmad Tarmizi <noor.azura.ahmad.tarmizi@intel.com> Link: https://lore.kernel.org/r/20230111050200.2130-1-noor.azura.ahmad.tarmizi@intel.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Sphinx 6.0 removed the execfile_() function, which we use as part of the
configuration process. They *did* warn us... Just open-code the
functionality as is done in Sphinx itself.
Tested (using SPHINX_CONF, since this code is only executed with an
alternative config file) on various Sphinx versions from 2.5 through 6.0.
Reported-by: Martin Liška <mliska@suse.cz> Cc: stable@vger.kernel.org Signed-off-by: Jonathan Corbet <corbet@lwn.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Nathan reports that recent kernels built with LTO will crash when doing
EFI boot using Fedora's GRUB and SHIM. The culprit turns out to be a
misaligned load from the TPM event log, which is annotated with
READ_ONCE(), and under LTO, this gets translated into a LDAR instruction
which does not tolerate misaligned accesses.
Interestingly, this does not happen when booting the same kernel
straight from the UEFI shell, and so the fact that the event log may
appear misaligned in memory may be caused by a bug in GRUB or SHIM.
However, using READ_ONCE() to access firmware tables is slightly unusual
in any case, and here, we only need to ensure that 'event' is not
dereferenced again after it gets unmapped, but this is already taken
care of by the implicit barrier() semantics of the early_memunmap()
call.
Cc: <stable@vger.kernel.org> Cc: Peter Jones <pjones@redhat.com> Cc: Jarkko Sakkinen <jarkko@kernel.org> Cc: Matthew Garrett <mjg59@srcf.ucam.org> Reported-by: Nathan Chancellor <nathan@kernel.org> Tested-by: Nathan Chancellor <nathan@kernel.org> Link: https://github.com/ClangBuiltLinux/linux/issues/1782 Signed-off-by: Ard Biesheuvel <ardb@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The following warning appears when executing:
make -C tools/testing/selftests/kvm
rseq_test.c: In function ‘main’:
rseq_test.c:237:33: warning: implicit declaration of function ‘gettid’; did you mean ‘getgid’? [-Wimplicit-function-declaration]
(void *)(unsigned long)gettid());
^~~~~~
getgid
/usr/bin/ld: /tmp/ccr5mMko.o: in function `main':
../kvm/tools/testing/selftests/kvm/rseq_test.c:237: undefined reference to `gettid'
collect2: error: ld returned 1 exit status
make: *** [../lib.mk:173: ../kvm/tools/testing/selftests/kvm/rseq_test] Error 1
Use the more compatible syscall(SYS_gettid) instead of gettid() to fix it.
More subsequent reuse may cause it to be wrapped in a lib file.
Starting from 13.0.0 llvm can generate SHT_REL section, see
https://reviews.llvm.org/rGca3bdb57fa1ac98b711a735de048c12b5fdd8086.
gen-hyprel does not support SHT_REL relocation section.
Filter out profile use flags to fix the build with profile optimization.
Signed-off-by: Denis Nikitin <denik@chromium.org> Signed-off-by: Marc Zyngier <maz@kernel.org> Link: https://lore.kernel.org/r/20221014184532.3153551-1-denik@chromium.org Signed-off-by: Stephen Boyd <swboyd@chromium.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A recent development on the EFI front has resulted in guests having
their page tables baked in the firmware binary, and mapped into the
IPA space as part of a read-only memslot. Not only is this legitimate,
but it also results in added security, so thumbs up.
It is possible to take an S1PTW translation fault if the S1 PTs are
unmapped at stage-2. However, KVM unconditionally treats S1PTW as a
write to correctly handle hardware AF/DB updates to the S1 PTs.
Furthermore, KVM injects an exception into the guest for S1PTW writes.
In the aforementioned case this results in the guest taking an abort
it won't recover from, as the S1 PTs mapping the vectors suffer from
the same problem.
So clearly our handling is... wrong.
Instead, switch to a two-pronged approach:
- On S1PTW translation fault, handle the fault as a read
- On S1PTW permission fault, handle the fault as a write
This is of no consequence to SW that *writes* to its PTs (the write
will trigger a non-S1PTW fault), and SW that uses RO PTs will not
use HW-assisted AF/DB anyway, as that'd be wrong.
Only in the case described in c4ad98e4b72c ("KVM: arm64: Assume write
fault on S1PTW permission fault on instruction fetch") do we end-up
with two back-to-back faults (page being evicted and faulted back).
I don't think this is a case worth optimising for.
Fixes: c4ad98e4b72c ("KVM: arm64: Assume write fault on S1PTW permission fault on instruction fetch") Reviewed-by: Oliver Upton <oliver.upton@linux.dev> Reviewed-by: Ard Biesheuvel <ardb@kernel.org> Regression-tested-by: Ard Biesheuvel <ardb@kernel.org> Signed-off-by: Marc Zyngier <maz@kernel.org> Cc: stable@vger.kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The HP Spectre x360 13-aw0xxx devices use the ALC285 codec with GPIO 0x04
controlling the micmute LED and COEF 0x0b index 8 controlling the mute LED.
A quirk was added to make these work as well as a fixup.
If the offset + length goes over the ethernet + vlan header, then the
length is adjusted to copy the bytes that are within the boundaries of
the vlan_ethhdr scratchpad area. The remaining bytes beyond ethernet +
vlan header are copied directly from the skbuff data area.
Fix incorrect arithmetic operator: subtract, not add, the size of the
vlan header in case of double-tagged packets to adjust the length
accordingly to address CVE-2023-0179.
There is another Dell Latitude laptop (1028:0c03) with Realtek
codec ALC3254 which needs the ALC269_FIXUP_DELL4_MIC_NO_PRESENCE
instead of the default matched ALC269_FIXUP_DELL1_MIC_NO_PRESENCE.
Apply correct fixup for this particular model to enable headset mic.
Takes rwsem lock inside snd_ctl_elem_read instead of snd_ctl_elem_read_user
like it was done for write in commit 1fa4445f9adf1 ("ALSA: control - introduce
snd_ctl_notify_one() helper"). Doing this way we are also fixing the following
locking issue happening in the compat path which can be easily triggered and
turned into an use-after-free.
While experimenting with applying noqueue to a classful queue discipline,
we discovered a NULL pointer dereference in the __dev_queue_xmit()
path that generates a kernel OOPS:
Previously in commit d66d6c3152e8 ("net: sched: register noqueue
qdisc"), NULL was set for the noqueue discipline on noqueue init
so that __dev_queue_xmit() falls through for the noqueue case. This
also sets a bypass of the enqueue NULL check in the
register_qdisc() function for the struct noqueue_disc_ops.
Classful queue disciplines make it past the NULL check in
__dev_queue_xmit() because the discipline is set to htb (in this case),
and then in the call to __dev_xmit_skb(), it calls into htb_enqueue()
which grabs a leaf node for a class and then calls qdisc_enqueue() by
passing in a queue discipline which assumes ->enqueue() is not set to NULL.
Fix this by not allowing classes to be assigned to the noqueue
discipline. Linux TC Notes states that classes cannot be set to
the noqueue discipline. [1] Let's enforce that here.
Rasmus Villemoes [Thu, 22 Dec 2022 11:44:14 +0000 (12:44 +0100)]
serial: fixup backport of "serial: Deassert Transmit Enable on probe in driver-specific way"
When 7c7f9bc986e6 ("serial: Deassert Transmit Enable on probe in
driver-specific way") got backported to 5.15.y, there known as b079d3775237, some hunks were accidentally left out.
In fsl_lpuart.c, this amounts to uart_remove_one_port() being called
in an error path despite uart_add_one_port() not having been called.
In serial_core.c, it is possible that the omission in
uart_suspend_port() is harmless, but the backport did have the
corresponding hunk in uart_resume_port(), it runs counter to the
original commit's intention of
Skip any invocation of ->set_mctrl() if RS485 is enabled.
and it's certainly better to be aligned with upstream.
The hardware XRSTOR instruction resets the PKRU register to its hardware
init value (namely 0) if the PKRU bit is not set in the xfeatures mask.
Emulating that here restores the pre-5.14 behavior for PTRACE_SET_REGSET
with NT_X86_XSTATE, and makes sigreturn (which still uses XRSTOR) and
behave identically.
Fixes: e84ba47e313d ("x86/fpu: Hook up PKRU into ptrace()") Signed-off-by: Kyle Huey <me@kylehuey.com> Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com> Link: https://lore.kernel.org/all/20221115230932.7126-6-khuey%40kylehuey.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Handle PKRU in copy_uabi_to_xstate() for the benefit of APIs that write
the XSTATE such as PTRACE_SETREGSET with NT_X86_XSTATE.
This restores the pre-5.14 behavior of ptrace. The regression can be seen
by running gdb and executing `p $pkru`, `set $pkru = 42`, and `p $pkru`.
On affected kernels (5.14+) the write to the PKRU register (which gdb
performs through ptrace) is ignored.
Fixes: e84ba47e313d ("x86/fpu: Hook up PKRU into ptrace()") Signed-off-by: Kyle Huey <me@kylehuey.com> Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com> Link: https://lore.kernel.org/all/20221115230932.7126-5-khuey%40kylehuey.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In preparation for adding PKRU handling code into copy_uabi_to_xstate(),
add an argument that copy_uabi_from_kernel_to_xstate() can use to pass the
canonical location of the PKRU value. For
copy_sigframe_from_user_to_xstate() the kernel will actually restore the
PKRU value from the fpstate, but pass in the thread_struct's pkru location
anyways for consistency.
ptrace (through PTRACE_SETREGSET with NT_X86_XSTATE) ultimately calls
copy_uabi_from_kernel_to_xstate(). In preparation for eventually handling
PKRU in copy_uabi_to_xstate, pass in a pointer to the PKRU location.
Adjust some MADV_XXX constants to be in sync what their values are on
all other platforms. There is currently no reason to have an own
numbering on parisc, but it requires workarounds in many userspace
sources (e.g. glibc, qemu, ...) - which are often forgotten and thus
introduce bugs and different behaviour on parisc.
A wrapper avoids an ABI breakage for existing userspace applications by
translating any old values to the new ones, so this change allows us to
move over all programs to the new ABI over time.
For G200_SE_A, PLL M setting is wrong, which leads to blank screen,
or "signal out of range" on VGA display.
previous code had "m |= 0x80" which was changed to
m |= ((pixpllcn & BIT(8)) >> 1);
Tested on G200_SE_A rev 42
This line of code was moved to another file with
commit 877507bb954e ("drm/mgag200: Provide per-device callbacks for
PIXPLLC") but can be easily backported before this commit.
v2: * put BIT(7) First to respect MSB-to-LSB (Thomas)
* Add a comment to explain that this bit must be set (Thomas)
Fixes: 2dd040946ecf ("drm/mgag200: Store values (not bits) in struct mgag200_pll_values") Cc: stable@vger.kernel.org Signed-off-by: Jocelyn Falempe <jfalempe@redhat.com> Reviewed-by: Thomas Zimmermann <tzimmermann@suse.de> Link: https://patchwork.freedesktop.org/patch/msgid/20221013132810.521945-1-jfalempe@redhat.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Instead of blindly creating the EFI random seed configuration table if
the RNG protocol is implemented and works, check whether such a EFI
configuration table was provided by an earlier boot stage and if so,
concatenate the existing and the new seeds, leaving it up to the core
code to mix it in and credit it the way it sees fit.
This can be used for, e.g., systemd-boot, to pass an additional seed to
Linux in a way that can be consumed by the kernel very early. In that
case, the following definitions should be used to pass the seed to the
EFI stub:
struct linux_efi_random_seed {
u32 size; // of the 'seed' array in bytes
u8 seed[];
};
The memory for the struct must be allocated as EFI_ACPI_RECLAIM_MEMORY
pool memory, and the address of the struct in memory should be installed
as a EFI configuration table using the following GUID:
Note that doing so is safe even on kernels that were built without this
patch applied, but the seed will simply be overwritten with a seed
derived from the EFI RNG protocol, if available. The recommended seed
size is 32 bytes, and seeds larger than 512 bytes are considered
corrupted and ignored entirely.
In order to preserve forward secrecy, seeds from previous bootloaders
are memzero'd out, and in order to preserve memory, those older seeds
are also freed from memory. Freeing from memory without first memzeroing
is not safe to do, as it's possible that nothing else will ever
overwrite those pages used by EFI.
Reviewed-by: Jason A. Donenfeld <Jason@zx2c4.com>
[ardb: incorporate Jason's followup changes to extend the maximum seed
size on the consumer end, memzero() it and drop a needless printk] Signed-off-by: Ard Biesheuvel <ardb@kernel.org> Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 307af6c87937 ("mbcache: automatically delete entries from cache
on freeing") started nesting cache->c_list_lock under the bit locks
protecting hash buckets of the mbcache hash table in
mb_cache_entry_create(). This causes problems for real-time kernels
because there spinlocks are sleeping locks while bitlocks stay atomic.
Luckily the nesting is easy to avoid by holding entry reference until
the entry is added to the LRU list. This makes sure we cannot race with
entry deletion.
Cc: stable@kernel.org Fixes: 307af6c87937 ("mbcache: automatically delete entries from cache on freeing") Reported-by: Mike Galbraith <efault@gmx.de> Signed-off-by: Jan Kara <jack@suse.cz> Link: https://lore.kernel.org/r/20220908091032.10513-1-jack@suse.cz Signed-off-by: Theodore Ts'o <tytso@mit.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The refactoring of rx copybreak modifies the original return logic, which
will make this feature unavailable. So this patch fixes the return logic of
rx copybreak.
Fixes: e74a726da2c4 ("net: hns3: refactor hns3_nic_reuse_page()") Fixes: 99f6b5fb5f63 ("net: hns3: use bounce buffer when rx page can not be reused") Signed-off-by: Jie Wang <wangjie125@huawei.com> Signed-off-by: Hao Lan <lanhao@huawei.com> Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Previous commit a05d3c915314 ("btrfs: check superblock to ensure the fs
was not modified at thaw time") only checks the content of the super
block, but it doesn't really check if the on-disk super block has a
matching checksum.
This patch will add the checksum verification to thaw time superblock
verification.
This involves the following extra changes:
- Export btrfs_check_super_csum()
As we need to call it in super.c.
- Change the argument list of btrfs_check_super_csum()
Instead of passing a char *, directly pass struct btrfs_super_block *
pointer.
- Verify that our checksum type didn't change before checking the
checksum value, like it's done at mount time
Fixes: a05d3c915314 ("btrfs: check superblock to ensure the fs was not modified at thaw time") Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com> Signed-off-by: Qu Wenruo <wqu@suse.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The build of kselftests fails if relative path is specified through
KBUILD_OUTPUT or O=<path> method. BUILD variable is used to determine
the path of the output objects. When make is run from other directories
with relative paths, the exact path of the build objects is ambiguous
and build fails.
Set the BUILD variable to the absolute path of the output directory.
Make the logic readable and easy to follow. Use spaces instead of tabs
for indentation as if with tab indentation is considered recipe in make.
Mounting a filesystem whose journal inode has the encrypt flag causes a
NULL dereference in fscrypt_limit_io_blocks() when the 'inlinecrypt'
mount option is used.
The problem is that when jbd2_journal_init_inode() calls bmap(), it
eventually finds its way into ext4_iomap_begin(), which calls
fscrypt_limit_io_blocks(). fscrypt_limit_io_blocks() requires that if
the inode is encrypted, then its encryption key must already be set up.
That's not the case here, since the journal inode is never "opened" like
a normal file would be. Hence the crash.
To fix this, make ext4 consider journal inodes with the encrypt flag to
be invalid. (Note, maybe other flags should be rejected on the journal
inode too. For now, this is just the minimal fix for the above issue.)
I've marked this as fixing the commit that introduced the call to
fscrypt_limit_io_blocks(), since that's what made an actual crash start
being possible. But this fix could be applied to any version of ext4
that supports the encrypt feature.
Reported-by: syzbot+ba9dac45bc76c490b7c3@syzkaller.appspotmail.com Fixes: 38ea50daa7a4 ("ext4: support direct I/O with fscrypt using blk-crypto") Cc: stable@vger.kernel.org Signed-off-by: Eric Biggers <ebiggers@google.com> Link: https://lore.kernel.org/r/20221102053312.189962-1-ebiggers@kernel.org Signed-off-by: Theodore Ts'o <tytso@mit.edu> Cc: stable@kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Before, only the destructor from TCP request sock in IPv4 was called
even if the subflow was IPv6.
It is important to use the right destructor to avoid memory leaks with
some advanced IPv6 features, e.g. when the request socks contain
specific IPv6 options.
Fixes: 79c0949e9a09 ("mptcp: Add key generation and token tree") Reviewed-by: Mat Martineau <mathew.j.martineau@linux.intel.com> Cc: stable@vger.kernel.org Signed-off-by: Matthieu Baerts <matthieu.baerts@tessares.net> Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
tcp_request_sock_ops structure is specific to IPv4. It should then not
be used with MPTCP subflows on top of IPv6.
For example, it contains the 'family' field, initialised to AF_INET.
This 'family' field is used by TCP FastOpen code to generate the cookie
but also by TCP Metrics, SELinux and SYN Cookies. Using the wrong family
will not lead to crashes but displaying/using/checking wrong things.
Note that 'send_reset' callback from request_sock_ops structure is used
in some error paths. It is then also important to use the correct one
for IPv4 or IPv6.
The slab name can also be different in IPv4 and IPv6, it will be used
when printing some log messages. The slab pointer will anyway be the
same because the object size is the same for both v4 and v6. A
BUILD_BUG_ON() has also been added to make sure this size is the same.
Fixes: cec37a6e41aa ("mptcp: Handle MP_CAPABLE options for outgoing connections") Reviewed-by: Mat Martineau <mathew.j.martineau@linux.intel.com> Cc: stable@vger.kernel.org Signed-off-by: Matthieu Baerts <matthieu.baerts@tessares.net> Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Revert "ACPI: PM: Add support for upcoming AMD uPEP HID AMDI007"
A number of AMD based Rembrandt laptops are not working properly in
suspend/resume. This has been root caused to be from the BIOS
implementation not populating code for the AMD GUID in uPEP, but
instead only the Microsoft one.
In later kernels this has been fixed by using the Microsoft GUID
instead.
The following series of patches has fixed it in newer kernels:
commit ed470febf837 ("ACPI: PM: s2idle: Add support for upcoming AMD uPEP HID AMDI008")
commit 1a2dcab517cb ("ACPI: PM: s2idle: Use LPS0 idle if ACPI_FADT_LOW_POWER_S0 is unset")
commit 100a57379380 ("ACPI: x86: s2idle: Move _HID handling for AMD systems into structures")
commit fd894f05cf30 ("ACPI: x86: s2idle: If a new AMD _HID is missing assume Rembrandt")
commit a0bc002393d4 ("ACPI: x86: s2idle: Add module parameter to prefer Microsoft GUID")
commit d0f61e89f08d ("ACPI: x86: s2idle: Add a quirk for ASUS TUF Gaming A17 FA707RE")
commit ddeea2c3cb88 ("ACPI: x86: s2idle: Add a quirk for ASUS ROG Zephyrus G14")
commit 888ca9c7955e ("ACPI: x86: s2idle: Add a quirk for Lenovo Slim 7 Pro 14ARH7")
commit 631b54519e8e ("ACPI: x86: s2idle: Add a quirk for ASUSTeK COMPUTER INC. ROG Flow X13")
commit 39f81776c680 ("ACPI: x86: s2idle: Fix a NULL pointer dereference")
commit 54bd1e548701 ("ACPI: x86: s2idle: Add another ID to s2idle_dmi_table")
commit 577821f756cf ("ACPI: x86: s2idle: Force AMD GUID/_REV 2 on HP Elitebook 865")
commit e6d180a35bc0 ("ACPI: x86: s2idle: Stop using AMD specific codepath for Rembrandt+")
This is needlessly complex for 5.15.y though. To accomplish the same
effective result revert commit f0c6225531e4 ("ACPI: PM: Add support for
upcoming AMD uPEP HID AMDI007") instead.
"nt_len - CIFS_ENCPWD_SIZE" is passed directly from
ksmbd_decode_ntlmssp_auth_blob to ksmbd_auth_ntlmv2. Malicious requests
can set nt_len to less than CIFS_ENCPWD_SIZE, which results in a negative
number (or large unsigned value) used for a subsequent memcpy in
ksmbd_auth_ntlvm2 and can cause a panic.
Fixes: e2f34481b24d ("cifsd: add server-side procedures for SMB3") Cc: stable@vger.kernel.org Signed-off-by: William Liu <will@willsroot.io> Signed-off-by: Hrvoje Mišetić <misetichrvoje@gmail.com> Acked-by: Namjae Jeon <linkinjeon@kernel.org> Signed-off-by: Steve French <stfrench@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If kernel_recvmsg() return -EAGAIN in ksmbd_tcp_readv() and go round
again, It will cause infinite loop issue. And all threads from next
connections would be doing that. This patch add max retry count(2) to
avoid it. kernel_recvmsg() will wait during 7sec timeout and try to
retry two time if -EAGAIN is returned. And add flags of kvmalloc to
__GFP_NOWARN and __GFP_NORETRY to disconnect immediately without
retrying on memory alloation failure.
Fixes: 0626e6641f6b ("cifsd: add server handler for central processing and tranport layers") Cc: stable@vger.kernel.org Reported-by: zdi-disclosures@trendmicro.com # ZDI-CAN-18259 Reviewed-by: Sergey Senozhatsky <senozhatsky@chromium.org> Signed-off-by: Namjae Jeon <linkinjeon@kernel.org> Signed-off-by: Steve French <stfrench@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 55d1cbbbb29e ("hfs/hfsplus: use WARN_ON for sanity check") fixed
a build warning by turning a comment into a WARN_ON(), but it turns out
that syzbot then complains because it can trigger said warning with a
corrupted hfs image.
The warning actually does warn about a bad situation, but we are much
better off just handling it as the error it is. So rather than warn
about us doing bad things, stop doing the bad things and return -EIO.
While at it, also fix a memory leak that was introduced by an earlier
fix for a similar syzbot warning situation, and add a check for one case
that historically wasn't handled at all (ie neither comment nor
subsequent WARN_ON).
Reported-by: syzbot+7bb7cd3595533513a9e7@syzkaller.appspotmail.com Fixes: 55d1cbbbb29e ("hfs/hfsplus: use WARN_ON for sanity check") Fixes: 8d824e69d9f3 ("hfs: fix OOB Read in __hfs_brec_find") Link: https://lore.kernel.org/lkml/000000000000dbce4e05f170f289@google.com/ Tested-by: Michael Schmitz <schmitzmic@gmail.com> Cc: Arnd Bergmann <arnd@arndb.de> Cc: Matthew Wilcox <willy@infradead.org> Cc: Viacheslav Dubeyko <slava@dubeyko.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
gcc warns about a couple of instances in which a sanity check exists but
the author wasn't sure how to react to it failing, which makes it look
like a possible bug:
fs/hfsplus/inode.c: In function 'hfsplus_cat_read_inode':
fs/hfsplus/inode.c:503:37: error: suggest braces around empty body in an 'if' statement [-Werror=empty-body]
503 | /* panic? */;
| ^
fs/hfsplus/inode.c:524:37: error: suggest braces around empty body in an 'if' statement [-Werror=empty-body]
524 | /* panic? */;
| ^
fs/hfsplus/inode.c: In function 'hfsplus_cat_write_inode':
fs/hfsplus/inode.c:582:37: error: suggest braces around empty body in an 'if' statement [-Werror=empty-body]
582 | /* panic? */;
| ^
fs/hfsplus/inode.c:608:37: error: suggest braces around empty body in an 'if' statement [-Werror=empty-body]
608 | /* panic? */;
| ^
fs/hfs/inode.c: In function 'hfs_write_inode':
fs/hfs/inode.c:464:37: error: suggest braces around empty body in an 'if' statement [-Werror=empty-body]
464 | /* panic? */;
| ^
fs/hfs/inode.c:485:37: error: suggest braces around empty body in an 'if' statement [-Werror=empty-body]
485 | /* panic? */;
| ^
panic() is probably not the correct choice here, but a WARN_ON
seems appropriate and avoids the compile-time warning.
Link: https://lkml.kernel.org/r/20210927102149.1809384-1-arnd@kernel.org Link: https://lore.kernel.org/all/20210322223249.2632268-1-arnd@kernel.org/ Signed-off-by: Arnd Bergmann <arnd@arndb.de> Reviewed-by: Christian Brauner <christian.brauner@ubuntu.com> Cc: Alexander Viro <viro@zeniv.linux.org.uk> Cc: Christian Brauner <christian.brauner@ubuntu.com> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: Jan Kara <jack@suse.cz> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Check carefully on root debugfs available when destroying vgpu,
e.g in remove case drm minor's debugfs root might already be destroyed,
which led to kernel oops like below.
When gvt debug fs is destroyed, need to have a sane check if drm
minor's debugfs root is still available or not, otherwise in case like
device remove through unbinding, drm minor's debugfs directory has
already been removed, then intel_gvt_debugfs_clean() would act upon
dangling pointer like below oops.
If the get_user(x, ptr) has x as a pointer, then the setting
of (x) = 0 is going to produce the following sparse warning,
so fix this by forcing the type of 'x' when access_ok() fails.
fs/aio.c:2073:21: warning: Using plain integer as NULL pointer
Jiffy to ktime CQ waiting conversion broke how we treat timeouts, in
particular we rearm it anew every time we get into
io_cqring_wait_schedule() without adjusting the timeout. Waiting for 2
CQEs and getting a task_work in the middle may double the timeout value,
or even worse in some cases task may wait indefinitely.
If we split a bio marked with REQ_NOWAIT, then we can trigger spurious
EAGAIN if constituent parts of that split bio end up failing request
allocations. Parts will complete just fine, but just a single failure
in one of the chained bios will yield an EAGAIN final result for the
parent bio.
Return EAGAIN early if we end up needing to split such a bio, which
allows for saner recovery handling.
Commit 62d89a7d49af ("video: fbdev: matroxfb: set maxvram of vbG200eW to
the same as vbG200 to avoid black screen") accidently decreases the
maximum memory size for the Matrox G200eW (102b:0532) from 8 MB to 1 MB
by missing one zero. This caused the driver initialization to fail with
the messages below, as the minimum required VRAM size is 2 MB:
So, add the missing 0 to make it the intended 16 MB. Successfully tested on
the Dell PowerEdge R910/0KYD3D, BIOS 2.10.0 08/29/2013, that the warning is
gone.
While at it, add a leading 0 to the maxdisplayable entry, so it’s aligned
properly. The value could probably also be increased from 8 MB to 16 MB, as
the G200 uses the same values, but I have not checked any datasheet.
Note, matroxfb is obsolete and superseded by the maintained DRM driver
mga200, which is used by default on most systems where both drivers are
available. Therefore, on most systems it was only a cosmetic issue.
Fixes: 62d89a7d49af ("video: fbdev: matroxfb: set maxvram of vbG200eW to the same as vbG200 to avoid black screen") Link: https://lore.kernel.org/linux-fbdev/972999d3-b75d-5680-fcef-6e6905c52ac5@suse.de/T/#mb6953a9995ebd18acc8552f99d6db39787aec775 Cc: it+linux-fbdev@molgen.mpg.de Cc: Z. Liu <liuzx@knownsec.com> Cc: Rich Felker <dalias@libc.org> Cc: stable@vger.kernel.org Signed-off-by: Paul Menzel <pmenzel@molgen.mpg.de> Signed-off-by: Helge Deller <deller@gmx.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If v4 READDIR operation hits a mountpoint and gets back an error,
then it will include that entry in the reply and set RDATTR_ERROR for it
to the error.
That's fine for "normal" exported filesystems, but on the v4root, we
need to be more careful to only expose the existence of dentries that
lead to exports.
If the mountd upcall times out while checking to see whether a
mountpoint on the v4root is exported, then we have no recourse other
than to fail the whole operation.
Cc: Steve Dickson <steved@redhat.com> Link: https://bugzilla.kernel.org/show_bug.cgi?id=216777 Reported-by: JianHong Yin <yin-jianhong@163.com> Signed-off-by: Jeff Layton <jlayton@kernel.org> Signed-off-by: Chuck Lever <chuck.lever@oracle.com> Cc: <stable@vger.kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
b3e34a47f989 ("x86/kexec: fix memory leak of elf header buffer"),
freeing image->elf_headers in the error path of crash_load_segments()
is not needed because kimage_file_post_load_cleanup() will take
care of that later. And not clearing it could result in a double-free.
Drop the superfluous vfree() call at the error path of
crash_load_segments().
[BACKGROUND]
There is an incident report that, one user hibernated the system, with
one btrfs on removable device still mounted.
Then by some incident, the btrfs got mounted and modified by another
system/OS, then back to the hibernated system.
After resuming from the hibernation, new write happened into the victim btrfs.
Now the fs is completely broken, since the underlying btrfs is no longer
the same one before the hibernation, and the user lost their data due to
various transid mismatch.
[REPRODUCER]
We can emulate the situation using the following small script:
# There is no way to mount the same cloned fs on the same system,
# as the conflicting fsid will be rejected by btrfs.
# Thus here we have to wipe the fs using a different btrfs.
mkfs.btrfs -f $dev.backup
The final fsck will fail due to some tree blocks has incorrect fsid.
This is enough to emulate the problem hit by the unfortunate user.
[ENHANCEMENT]
Although such case should not be that common, it can still happen from
time to time.
From the view of btrfs, we can detect any unexpected super block change,
and if there is any unexpected change, we just mark the fs read-only,
and thaw the fs.
By this we can limit the damage to minimal, and I hope no one would lose
their data by this anymore.
To be able to use the Commands Supported and Effects Log for allowing
unprivileged passtrough, it needs to be corretly reported for I/O
commands as well. Return the I/O command effects from
nvme_command_effects, and also add a default list of effects for the
NVM command set. For other command sets, the Commands Supported and
Effects log is required to be present already.
Signed-off-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Keith Busch <kbusch@kernel.org> Reviewed-by: Kanchan Joshi <joshi.k@samsung.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
We only check the register opcode value inside the restricted ring
section, move it into the main io_uring_register() function instead
and check it up front.
The flush request initialized by blk_kick_flush has NULL bio,
and it may be dealt with nvme_end_req during io completion.
When blktrace is enabled, nvme_trace_bio_complete with multipath
activated trying to access NULL pointer bio from flush request
results in the following crash:
The Advantech MICA-071 tablet deviates from the defaults for
a non CR Bay Trail based tablet in several ways:
1. It uses an analog MIC on IN3 rather then using DMIC1
2. It only has 1 speaker
3. It needs the OVCD current threshold to be set to 1500uA instead of
the default 2000uA to reliable differentiate between headphones vs
headsets
Add a quirk with these settings for this tablet.
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com> Link: https://lore.kernel.org/r/20221213123246.11226-1-hdegoede@redhat.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
When extending the last extent in the file within the last block, we
wrongly computed the length of the last extent. This is mostly a
cosmetical problem since the extent does not contain any data and the
length will be fixed up by following operations but still.
Fixes: 1f3868f06855 ("udf: Fix extending file within last block") Signed-off-by: Jan Kara <jack@suse.cz> Signed-off-by: Sasha Levin <sashal@kernel.org>
The --for-each-cgroup can have the same cgroup multiple times, but this
confuses BPF counters (since they have the same cgroup id), making only
the last cgroup events to be counted.
Let's check the cgroup name before adding a new entry to the cgroups
list.
Before:
$ sudo ./perf stat -a --bpf-counters --for-each-cgroup /,/ sleep 1
As a reminder, to test with BPF counters one has to use BUILD_BPF_SKEL=1
in the make command line and have clang/llvm installed when building
perf, otherwise the --bpf-counters option will not be available:
# perf stat -a --bpf-counters --for-each-cgroup /,/ sleep 1
Error: unknown option `bpf-counters'
Usage: perf stat [<options>] [<command>]
-a, --all-cpus system-wide collection from all CPUs
<SNIP>
#
Fixes: bb1c15b60b981d10 ("perf stat: Support regex pattern in --for-each-cgroup") Signed-off-by: Namhyung Kim <namhyung@kernel.org> Tested-by: Arnaldo Carvalho de Melo <acme@redhat.com> Cc: Adrian Hunter <adrian.hunter@intel.com> Cc: bpf@vger.kernel.org Cc: Ian Rogers <irogers@google.com> Cc: Ingo Molnar <mingo@kernel.org> Cc: Jiri Olsa <jolsa@kernel.org> Cc: Namhyung Kim <namhyung@kernel.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Song Liu <songliubraving@fb.com> Link: https://lore.kernel.org/r/20230104064402.1551516-5-namhyung@kernel.org Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Variables off and len typed as uint32 in rndis_query function
are controlled by incoming RNDIS response message thus their
value may be manipulated. Setting off to a unexpectetly large
value will cause the sum with len and 8 to overflow and pass
the implemented validation step. Consequently the response
pointer will be referring to a location past the expected
buffer boundaries allowing information leakage e.g. via
RNDIS_OID_802_3_PERMANENT_ADDRESS OID.
Fixes: ddda08624013 ("USB: rndis_host, various cleanups") Signed-off-by: Szymon Heidrich <szymon.heidrich@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Current code uses per_cpu pointer to get the lmtst_id mapped to
the core on which aura_free() is executed. Using per_cpu pointer
without preemption disable causing mismatch between lmtst_id and
core on which pointer gets freed. This patch fixes the issue by
disabling preemption around aura_free.
Fixes: ef6c8da71eaf ("octeontx2-pf: cn10K: Reserve LMTST lines per core") Signed-off-by: Sunil Goutham <sgoutham@marvell.com> Signed-off-by: Geetha sowjanya <gakula@marvell.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
syzbot is reporting hung task at do_user_addr_fault() [1], for there is
a silent deadlock between PG_locked bit and ni_lock lock.
Since filemap_update_page() calls filemap_read_folio() after calling
folio_trylock() which will set PG_locked bit, ntfs_truncate() must not
call truncate_setsize() which will wait for PG_locked bit to be cleared
when holding ni_lock lock.
ipu_src_rect_width() was introduced to support odd screen resolutions
such as 1366x768 by internally rounding up primary plane width to a
multiple of 8 and compensating with reduced horizontal blanking.
This also caused overlay plane width to be rounded up, which was not
intended. Fix overlay plane width by limiting the rounding up to the
primary plane.
drm_rect_width(&new_state->src) >> 16 is the same value as
drm_rect_width(dst) because there is no plane scaling support.
When adding/deleting large number of elements in one step in ipset, it can
take a reasonable amount of time and can result in soft lockup errors. The
patch 5f7b51bf09ba ("netfilter: ipset: Limit the maximal range of
consecutive elements to add/delete") tried to fix it by limiting the max
elements to process at all. However it was not enough, it is still possible
that we get hung tasks. Lowering the limit is not reasonable, so the
approach in this patch is as follows: rely on the method used at resizing
sets and save the state when we reach a smaller internal batch limit,
unlock/lock and proceed from the saved state. Thus we can avoid long
continuous tasks and at the same time removed the limit to add/delete large
number of elements in one step.
The nfnl mutex is held during the whole operation which prevents one to
issue other ipset commands in parallel.
Fixes: 5f7b51bf09ba ("netfilter: ipset: Limit the maximal range of consecutive elements to add/delete") Reported-by: syzbot+9204e7399656300bf271@syzkaller.appspotmail.com Signed-off-by: Jozsef Kadlecsik <kadlec@netfilter.org> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The hash:net,port,net set type supports /0 subnets. However, the patch
commit 5f7b51bf09baca8e titled "netfilter: ipset: Limit the maximal range
of consecutive elements to add/delete" did not take into account it and
resulted in an endless loop. The bug is actually older but the patch 5f7b51bf09baca8e brings it out earlier.
Handle /0 subnets properly in hash:net,port,net set types.
Fixes: 5f7b51bf09ba ("netfilter: ipset: Limit the maximal range of consecutive elements to add/delete") Reported-by: Марк Коренберг <socketpair@gmail.com> Signed-off-by: Jozsef Kadlecsik <kadlec@netfilter.org> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
There is an issue with the checking of the return value of
'of_get_mac_address', which returns 0 on success and negative value on
failure. The driver interpretated the result the opposite way. Therefore
if there was a MAC address defined in the DT, then the driver was
generating a random MAC address otherwise it would use address 0.
Fix this by checking correctly the return value of 'of_get_mac_address'
Fixes: b74ef9f9cb91 ("net: sparx5: Do not use mac_addr uninitialized in mchp_sparx5_probe()") Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
If asked to drop a packet via TC_ACT_SHOT it is unsafe to assume
res.class contains a valid pointer Fixes: b0188d4dbe5f ("[NET_SCHED]: sch_atm: Lindent") Signed-off-by: Jamal Hadi Salim <jhs@mojatatu.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
of_irq_find_parent() returns a node pointer with refcount incremented,
We should use of_node_put() on it when not needed anymore.
Add missing of_node_put() to avoid refcount leak.
For the POSIX locks they are using the same owner, which is the
thread id. And multiple POSIX locks could be merged into single one,
so when checking whether the 'file' has locks may fail.
For a file where some openers use locking and others don't is a
really odd usage pattern though. Locks are like stoplights -- they
only work if everyone pays attention to them.
Just switch ceph_get_caps() to check whether any locks are set on
the inode. If there are POSIX/OFD/FLOCK locks on the file at the
time, we should set CHECK_FILELOCK, regardless of what fd was used
to set the lock.
Fixes: ff5d913dfc71 ("ceph: return -EIO if read/write against filp that lost file locks") Signed-off-by: Xiubo Li <xiubli@redhat.com> Reviewed-by: Jeff Layton <jlayton@kernel.org> Reviewed-by: Ilya Dryomov <idryomov@gmail.com> Signed-off-by: Ilya Dryomov <idryomov@gmail.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Ceph has a need to know whether a particular inode has any locks set on
it. It's currently tracking that by a num_locks field in its
filp->private_data, but that's problematic as it tries to decrement this
field when releasing locks and that can race with the file being torn
down.
Add a new vfs_inode_has_locks helper that just returns whether any locks
are currently held on the inode.
Reviewed-by: Xiubo Li <xiubli@redhat.com> Reviewed-by: Christoph Hellwig <hch@infradead.org> Signed-off-by: Jeff Layton <jlayton@kernel.org>
Stable-dep-of: 461ab10ef7e6 ("ceph: switch to vfs_inode_has_locks() to fix file lock bug") Signed-off-by: Sasha Levin <sashal@kernel.org>
Having a bigger number of FIFO lines held after vsync is only useful to
SoCs using AFBC to give time to the AFBC decoder to be reset, configured
and enabled again.
For SoCs not using AFBC this, on the contrary, is causing on some
displays issues and a few pixels vertical offset in the displayed image.
Conditionally increase the number of lines held after vsync only for
SoCs using AFBC, leaving the default value for all the others.
Fixes: 24e0d4058eff ("drm/meson: hold 32 lines after vsync to give time for AFBC start") Signed-off-by: Carlo Caione <ccaione@baylibre.com> Acked-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Acked-by: Neil Armstrong <neil.armstrong@linaro.org>
[narmstrong: added fixes tag] Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org> Link: https://patchwork.freedesktop.org/patch/msgid/20221216-afbc_s905x-v1-0-033bebf780d9@baylibre.com Signed-off-by: Sasha Levin <sashal@kernel.org>
Currently, when modifying DC, we validate max_rd_atomic user attribute
against the RC cap, validate against DC. RC and DC QP types have different
device limitations.
This can cause userspace created DC QPs to malfunction.
projects / linux.git / log