phy: ti: tusb1210: Define device IDs

Define device IDs since some of them are being used more than once.

Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20240209160334.2304230-3-andriy.shevchenko@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>

phy: ti: tusb1210: Use temporary variable for struct device

Use temporary variable for struct device to make code neater.

Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20240209160334.2304230-2-andriy.shevchenko@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>

phy: rockchip: Add Samsung HDMI/eDP Combo PHY driver

Add driver for the HDMI/eDP TX Combo PHY found on Rockchip RK3588 SoC.

The PHY is based on a Samsung IP block and supports HDMI 2.1 TMDS, FRL
and eDP links.  The maximum data rate is 12Gbps (FRL), while the minimum
is 250Mbps (TMDS).

Only the TMDS link is currently supported.

Co-developed-by: Algea Cao <algea.cao@rock-chips.com>
Signed-off-by: Algea Cao <algea.cao@rock-chips.com>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Cristian Ciocaltea <cristian.ciocaltea@collabora.com>
Link: https://lore.kernel.org/r/20240214-phy-hdptx-v4-2-e7974f46c1a7@collabora.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>

dt-bindings: phy: Add Rockchip HDMI/eDP Combo PHY schema

Add dt-binding schema for the HDMI/eDP Transmitter Combo PHY found on
Rockchip RK3588 SoC.

Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Cristian Ciocaltea <cristian.ciocaltea@collabora.com>
Link: https://lore.kernel.org/r/20240214-phy-hdptx-v4-1-e7974f46c1a7@collabora.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>

phy: ti: gmii-sel: add resume support

The resume callback restores the submode of each PHY.

It uses the submode stored in struct phy_gmii_sel_phy_priv (variable
phy_if_mode). The submode was saved by the set_mode PHY operation.

Signed-off-by: Thomas Richard <thomas.richard@bootlin.com>
Link: https://lore.kernel.org/r/20240125171754.773909-1-thomas.richard@bootlin.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>

phy: mtk-mipi-csi: add driver for CSI phy

This is a new driver that supports the MIPI CSI CD-PHY version 0.5

The number of PHYs depend on the SoC.
Each PHY can support D-PHY only or CD-PHY configuration.
The driver supports only D-PHY mode, so CD-PHY
compatible PHY are configured in D-PHY mode.

[Julien Stephan: simplify driver model: one instance per phy vs
one instance for all phys]

Signed-off-by: Louis Kuo <louis.kuo@mediatek.com>
Signed-off-by: Phi-bang Nguyen <pnguyen@baylibre.com>
[Julien Stephan: refactor code]
Co-developed-by: Julien Stephan <jstephan@baylibre.com>
Signed-off-by: Julien Stephan <jstephan@baylibre.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20240111101738.468916-1-jstephan@baylibre.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>

dt-bindings: phy: add mediatek MIPI CD-PHY module v0.5

This adds the bindings, for the MIPI CD-PHY module v0.5 embedded in
some Mediatek soc, such as the mt8365

Signed-off-by: Florian Sylvestre <fsylvestre@baylibre.com>
Signed-off-by: Julien Stephan <jstephan@baylibre.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20240111101504.468169-2-jstephan@baylibre.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>

phy: cadence-torrent: Add USXGMII(156.25MHz) + SGMII/QSGMII(100MHz) multilink config for TI J7200

Add a separate compatible and registers map table for TI J7200.
TI J7200 uses Torrent SD0805 version which is a special version
derived from Torrent SD0801 with some differences in register
configurations.

Add register sequences for USXGMII(156.25MHz) + SGMII/QSGMII(100MHz)
multilink config for TI J7200. USXGMII uses PLL0 and SGMII/QSGMII
uses PLL1.

Signed-off-by: Swapnil Jakhade <sjakhade@cadence.com>
Reviewed-by: Roger Quadros <rogerq@kernel.org>
Link: https://lore.kernel.org/r/20240104133013.2911035-6-sjakhade@cadence.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>

dt-bindings: phy: cadence-torrent: Add a separate compatible for TI J7200

TI J7200 uses Torrent SD0805 version which is a special version derived
from Torrent SD0801 with some differences in register configurations.
Add a separate compatible for TI J7200 platforms.

Signed-off-by: Swapnil Jakhade <sjakhade@cadence.com>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Reviewed-by: Roger Quadros <rogerq@kernel.org>
Link: https://lore.kernel.org/r/20240104133013.2911035-5-sjakhade@cadence.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>

phy: cadence-torrent: Add USXGMII(156.25MHz) + SGMII/QSGMII(100MHz) multilink configuration

Add register sequences for USXGMII(156.25MHz) + SGMII/QSGMII(100MHz)
multilink configuration. USXGMII uses PLL0 and SGMII/QSGMII uses PLL1.

Signed-off-by: Swapnil Jakhade <sjakhade@cadence.com>
Reviewed-by: Roger Quadros <rogerq@kernel.org>
Link: https://lore.kernel.org/r/20240104133013.2911035-4-sjakhade@cadence.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>

phy: cadence-torrent: Add PCIe(100MHz) + USXGMII(156.25MHz) multilink configuration

Torrent PHY can have separate input reference clocks for PLL0 and PLL1.
Add support for dual reference clock multilink configurations.

Add register sequences for PCIe(100MHz) + USXGMII(156.25MHz) multilink
configuration. PCIe uses PLL0 and USXGMII uses PLL1.

Signed-off-by: Swapnil Jakhade <sjakhade@cadence.com>
Reviewed-by: Roger Quadros <rogerq@kernel.org>
Link: https://lore.kernel.org/r/20240104133013.2911035-3-sjakhade@cadence.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>

dt-bindings: phy: cadence-torrent: Add optional input reference clock for PLL1

Add a new optional input reference clock (pll1_refclk) for PLL1.
Update bindings to support dual reference clock multilink configurations.

Signed-off-by: Swapnil Jakhade <sjakhade@cadence.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Roger Quadros <rogerq@kernel.org>
Link: https://lore.kernel.org/r/20240104133013.2911035-2-sjakhade@cadence.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>

phy: qcom-qmp-ufs: Switch to devm_clk_bulk_get_all() API

Device drivers should just rely on the clocks provided by the devicetree
and enable/disable them based on the requirement. There is no need to
validate the clocks provided by devicetree in the driver. That's the job
of DT schema.

So let's switch to devm_clk_bulk_get_all() API that just gets the clocks
provided by devicetree and remove hardcoded clocks info.

Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20240131-ufs-phy-clock-v3-2-58a49d2f4605@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>

dt-bindings: phy: qmp-ufs: Fix PHY clocks

All QMP UFS PHYs except MSM8996 require 3 clocks:

* ref - 19.2MHz reference clock from RPMh
* ref_aux - Auxiliary reference clock from GCC
* qref - QREF clock from GCC or TCSR (since SM8550)

MSM8996 only requires 'ref' and 'qref' clocks. Hence, fix the binding to
reflect the actual clock topology.

This change obviously breaks the ABI, but it is inevitable since the
clock topology needs to be accurately described in the binding.

Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20240131-ufs-phy-clock-v3-1-58a49d2f4605@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>

phy: qcom: sgmii-eth: move PCS registers to separate header

Follow the example of the rest of the QMP PHY drivers and move SGMII PCS
registers to a separate header file.

Cc: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20240126-phy-qmp-merge-common-v2-8-a463d0b57836@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>

phy: qcom: sgmii-eth: use existing register definitions

The Qualcomm SGMII SerDes PHY is a QMP PHY. As such, it uses standard
registers for QSERDES COM/RX/TX regions. Use register defines from the
existing headers.

Cc: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20240126-phy-qmp-merge-common-v2-7-a463d0b57836@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>

phy: qcom: qmp-usbc: drop has_pwrdn_delay handling

None of the PHYs supported by the USBC driver need power down delay.
Drop corresponding flag and code.

Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20240126-phy-qmp-merge-common-v2-6-a463d0b57836@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>

phy: qcom: qmp: move common bits definitions to common header

Move bit definitions for the common headers to the common phy-qcom-qmp.h
header.

Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20240126-phy-qmp-merge-common-v2-5-a463d0b57836@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>

phy: qcom: qmp: split DP PHY registers to separate headers

Split the DP PHY register definitions to separate headers, removing them
from the global one.

Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20240126-phy-qmp-merge-common-v2-4-a463d0b57836@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>

phy: qcom: qmp: move common functions to common header

Move common init tables code to the common header phy-qcom-qmp-common.h.

Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20240126-phy-qmp-merge-common-v2-3-a463d0b57836@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>

phy: qcom: qmp-usb-legacy: drop qmp_usb_legacy_iomap

All PHYs supported by qmp-usb-legacy driver don't have issues with the
PCS region. Replace qmp_usb_legacy_iomap() with devm_of_iomap().

Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20240126-phy-qmp-merge-common-v2-2-a463d0b57836@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>

phy: qcom: qmp-usb-legacy: drop single-lane support

All PHYs supported by usb-legacy have two lanes. Drop support for
single-lane configuration.

Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Konrad DYbcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20240126-phy-qmp-merge-common-v2-1-a463d0b57836@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>

phy: qcom: qmp-pcie: Update PCIe0 PHY settings for SM8550

Align PCIe0 PHY settings with SM8550 latest PCIe PHY Hardware Programming
Guide.

Signed-off-by: Qiang Yu <quic_qianyu@quicinc.com>
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on SM8550-HDK
Link: https://lore.kernel.org/r/1703742157-69840-3-git-send-email-quic_qianyu@quicinc.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>

phy: qcom: qmp-pcie: Update PCIe1 PHY settings for SM8550

Align PCIe1 PHY settings with SM8550 latest PCIe PHY Hardware Programming
Guide.

Signed-off-by: Can Guo <quic_cang@quicinc.com>
Signed-off-by: Qiang Yu <quic_qianyu@quicinc.com>
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on SM8550-HDK
Link: https://lore.kernel.org/r/1703742157-69840-2-git-send-email-quic_qianyu@quicinc.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>

phy: armada-38x: add mux value for gbe port 0 on serdes 0

Armada 38x supports 3 functions on serdes #0:
- pcie port 0
- sata port 0
- gbe port 0

Add missing entry for gbe port 0 on serdes 0 to the gbe_mux array.

Because this array looks obscure to new readers, also add a comment
explaining the meaning of rows, columns and values.

Signed-off-by: Josua Mayer <josua@solid-run.com>
Link: https://lore.kernel.org/r/20240106-fix-a38x-comphy-sd0-gbe0-v1-1-c7fd87272050@solid-run.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>

phy: qcom-qmp-pcie: Add support for X1E80100 g3x2 and g4x2 PCIE

Add the X1E80100 G3 and G4 configurations.

Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20231223-x1e80100-phy-pcie-v2-3-223c0556908a@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>

phy: qcom: qmp-pcie: Add QMP v6 registers layout

For consistency, add the QMP v6 registers layout even though
they are the same as v5. Also switch all QMP v6 PHYs to use this
new layout.

Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20231223-x1e80100-phy-pcie-v2-2-223c0556908a@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>

dt-bindings: phy: qcom,sc8280xp-qmp-pcie-phy: Document the X1E80100 QMP PCIe PHYs

Document the QMP PCIe PHYs on the X1E80100 platform.

Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
Link: https://lore.kernel.org/r/20231223-x1e80100-phy-pcie-v2-1-223c0556908a@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>

phy: qcom: qmp-usbc: enable SDM630 support

Provide PHY configuration for the USB QMP PHY for the SDM630 / SDM660
platforms.

Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20240116-sdm660-usb3-support-v1-2-2fbd683aea77@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>

dt-bindings: phy: qcom,msm8998-qmp-usb3-phy: support SDM660

Declare the USB-C QMP PHY present on the Qualcomm SDM660 / SDM630
platforms.

Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20240116-sdm660-usb3-support-v1-1-2fbd683aea77@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>

phy: qcom: qmp-usbc: handle CLAMP register in a correct way

The QMP USB PHYs on msm8998, qcm2290 and some other platforms don't have
the PCS_MISC_CLAMP_ENABLE register. Instead they need to toggle the
register in the TCSR space. Make the new phy-qcom-qmp-usbc driver
correctly handle the clamp register.

Fixes: a51969fafc82 ("phy: qcom-qmp: Add QMP V3 USB3 PHY support for msm8998")
Fixes: 8abe5e778b2c ("phy: qcom-qmp: Add QCM2290 USB3 PHY support")
Cc: Jeffrey Hugo <quic_jhugo@quicinc.com>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Acked-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20240117-usbc-phy-vls-clamp-v2-3-a950c223f10f@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>

dt-bindings: phy: qcom,msm8998-qmp-usb3-phy: add TCSR registers

The QMP USB PHYs on msm8998, qcm2290 and some other platforms don't have
the PCS_MISC_CLAMP_ENABLE register. Instead they need to toggle the
register in the TCSR space. Declare the registers accessible through the
TCSR space.

Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20240117-usbc-phy-vls-clamp-v2-2-a950c223f10f@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>

phy: qcom: qmp-usbc: add support for the Type-C handling

The USB-C PHYs on the msm8998, QCM2290 and SM6115 platforms use special
register to control which lanes of the Type-C port are used for the
SuperSpeed USB connection. Mimic the qmp-combo driver and handle this
register.

Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20240113-pmi632-typec-v2-12-182d9aa0a5b3@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>

phy: qcom: qmp-usb: drop dual-lane handling

Now as all dual-lane PHYs have been migrated to a new driver, drop
support for dual lanes configuration. If the PHY uses two lanes for USB,
it is symthom that it should use either a combo USB+DP or a USB-C PHY
driver.

Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20240113-pmi632-typec-v2-11-182d9aa0a5b3@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>

phy: qcom: qmp-usb: split USB-C PHY driver

In preparation to adding Type-C handling for MSM8998, QCM2290 and SM6115
platforms, create new QMP USB-C PHY driver by splitting mentioned
platforms to a separate file. In future it will also be extended with
support for the DisplayPort handling. It will also be reused later for
such platforms as SDM660, SM6125, SM6150.

Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Acked-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20240113-pmi632-typec-v2-10-182d9aa0a5b3@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>

dt-bindings: phy: qcom,msm8998-qmp-usb3-phy: support USB-C data

Extend the Qualcomm USB-C QMP PHY schema with the USB-C related entry
points: orientation-switch property and USB-C connection graph.

Reviewed-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20240113-pmi632-typec-v2-4-182d9aa0a5b3@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>

dt-bindings: phy: qcom,msm8998-qmp-usb3-phy: split from sc8280xp PHY schema

In preparation to defining the USB-C handling on MSM8998, QCM2290 and
SM6115 split existing QMP USB3 PHY schema into pure USB3 and USB-C
schema definitions.

Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20240113-pmi632-typec-v2-3-182d9aa0a5b3@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>

phy: qualcomm: phy-qcom-qmp-ufs: Add High Speed Gear 5 support for SM8550

On SM8550, two sets of UFS PHY settings are provided, one set is to support
HS-G5, another set is to support HS-G4 and lower gears. The two sets of PHY
settings are programming different values to different registers, mixing
the two sets and/or overwriting one set with another set is definitely not
blessed by UFS PHY designers.

To add HS-G5 support for SM8550, split the two sets of PHY settings into
their dedicated overlay tables, only the common parts of the two sets of
PHY settings are left in the .tbls.

Consider we are going to add even higher gear support in future, to avoid
adding more tables with different names, rename the .tbls_hs_g4 and make it
an array, a size of 2 is enough as of now.

In this case, .tbls alone is not a complete set of PHY settings, so either
tbls_hs_overlay[0] or tbls_hs_overlay[1] must be applied on top of the
.tbls to become a complete set of PHY settings.

Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Can Guo <quic_cang@quicinc.com>
Link: https://lore.kernel.org/r/1703557892-1822-1-git-send-email-quic_cang@quicinc.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>

phy: qcom: qmp-ufs: Add SC7180 support

The SC7180 UFS PHY is identical to the one found on SM7150. Add a
compatible for it.

Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: David Wronek <davidwronek@gmail.com>
Link: https://lore.kernel.org/r/20240121-sm7125-upstream-v4-5-f7d1212c8ebb@gmail.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>

dt-bindings: phy: Add QMP UFS PHY compatible for SC7180

Document the QMP UFS PHY compatible for SC7180

Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: David Wronek <davidwronek@gmail.com>
Link: https://lore.kernel.org/r/20240121-sm7125-upstream-v4-3-f7d1212c8ebb@gmail.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>

Linux 6.8-rc1

Merge tag 'bcachefs-2024-01-21' of https://evilpiepirate.org/git/bcachefs

Pull more bcachefs updates from Kent Overstreet:
 "Some fixes, Some refactoring, some minor features:

   - Assorted prep work for disk space accounting rewrite

   - BTREE_TRIGGER_ATOMIC: after combining our trigger callbacks, this
     makes our trigger context more explicit

   - A few fixes to avoid excessive transaction restarts on
     multithreaded workloads: fstests (in addition to ktest tests) are
     now checking slowpath counters, and that's shaking out a few bugs

   - Assorted tracepoint improvements

   - Starting to break up bcachefs_format.h and move on disk types so
     they're with the code they belong to; this will make room to start
     documenting the on disk format better.

   - A few minor fixes"

* tag 'bcachefs-2024-01-21' of https://evilpiepirate.org/git/bcachefs: (46 commits)
  bcachefs: Improve inode_to_text()
  bcachefs: logged_ops_format.h
  bcachefs: reflink_format.h
  bcachefs; extents_format.h
  bcachefs: ec_format.h
  bcachefs: subvolume_format.h
  bcachefs: snapshot_format.h
  bcachefs: alloc_background_format.h
  bcachefs: xattr_format.h
  bcachefs: dirent_format.h
  bcachefs: inode_format.h
  bcachefs; quota_format.h
  bcachefs: sb-counters_format.h
  bcachefs: counters.c -> sb-counters.c
  bcachefs: comment bch_subvolume
  bcachefs: bch_snapshot::btime
  bcachefs: add missing __GFP_NOWARN
  bcachefs: opts->compression can now also be applied in the background
  bcachefs: Prep work for variable size btree node buffers
  bcachefs: grab s_umount only if snapshotting
  ...

Merge tag 'timers-core-2024-01-21' of git://git./linux/kernel/git/tip/tip

Pull timer updates from Thomas Gleixner:
 "Updates for time and clocksources:

   - A fix for the idle and iowait time accounting vs CPU hotplug.

     The time is reset on CPU hotplug which makes the accumulated
     systemwide time jump backwards.

   - Assorted fixes and improvements for clocksource/event drivers"

* tag 'timers-core-2024-01-21' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  tick-sched: Fix idle and iowait sleeptime accounting vs CPU hotplug
  clocksource/drivers/ep93xx: Fix error handling during probe
  clocksource/drivers/cadence-ttc: Fix some kernel-doc warnings
  clocksource/drivers/timer-ti-dm: Fix make W=n kerneldoc warnings
  clocksource/timer-riscv: Add riscv_clock_shutdown callback
  dt-bindings: timer: Add StarFive JH8100 clint
  dt-bindings: timer: thead,c900-aclint-mtimer: separate mtime and mtimecmp regs

Merge tag 'powerpc-6.8-2' of git://git./linux/kernel/git/powerpc/linux

Pull powerpc fixes from Aneesh Kumar:

 - Increase default stack size to 32KB for Book3S

Thanks to Michael Ellerman.

* tag 'powerpc-6.8-2' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
  powerpc/64s: Increase default stack size to 32KB

bcachefs: Improve inode_to_text()

Add line breaks - inode_to_text() is now much easier to read.

Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>

bcachefs: logged_ops_format.h

Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>

bcachefs: reflink_format.h

Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>

bcachefs; extents_format.h

Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>

bcachefs: ec_format.h

Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>

bcachefs: subvolume_format.h

Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>

bcachefs: snapshot_format.h

Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>

bcachefs: alloc_background_format.h

Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>

bcachefs: xattr_format.h

Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>

bcachefs: dirent_format.h

Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>

bcachefs: inode_format.h

Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>

bcachefs; quota_format.h

Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>

bcachefs: sb-counters_format.h

bcachefs_format.h has gotten too big; let's do some organizing.

Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>

bcachefs: counters.c -> sb-counters.c

Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>

bcachefs: comment bch_subvolume

Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>

bcachefs: bch_snapshot::btime

Add a field to bch_snapshot for creation time; this will be important
when we start exposing the snapshot tree to userspace.

Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>

bcachefs: add missing __GFP_NOWARN

Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>

bcachefs: opts->compression can now also be applied in the background

The "apply this compression method in the background" paths now use the
compression option if background_compression is not set; this means that
setting or changing the compression option will cause existing data to
be compressed accordingly in the background.

Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>

bcachefs: Prep work for variable size btree node buffers

bcachefs btree nodes are big - typically 256k - and btree roots are
pinned in memory. As we're now up to 18 btrees, we now have significant
memory overhead in mostly empty btree roots.

And in the future we're going to start enforcing that certain btree node
boundaries exist, to solve lock contention issues - analagous to XFS's
AGIs.

Thus, we need to start allocating smaller btree node buffers when we
can. This patch changes code that refers to the filesystem constant
c->opts.btree_node_size to refer to the btree node buffer size -
btree_buf_bytes() - where appropriate.

Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>

bcachefs: grab s_umount only if snapshotting

When I was testing mongodb over bcachefs with compression,
there is a lockdep warning when snapshotting mongodb data volume.

$ cat test.sh
prog=bcachefs

$prog subvolume create /mnt/data
$prog subvolume create /mnt/data/snapshots

while true;do
    $prog subvolume snapshot /mnt/data /mnt/data/snapshots/$(date +%s)
    sleep 1s
done

$ cat /etc/mongodb.conf
systemLog:
  destination: file
  logAppend: true
  path: /mnt/data/mongod.log

storage:
  dbPath: /mnt/data/

lockdep reports:
[ 3437.452330] ======================================================
[ 3437.452750] WARNING: possible circular locking dependency detected
[ 3437.453168] 6.7.0-rc7-custom+ #85 Tainted: G            E
[ 3437.453562] ------------------------------------------------------
[ 3437.453981] bcachefs/35533 is trying to acquire lock:
[ 3437.454325] ffffa0a02b2b1418 (sb_writers#10){.+.+}-{0:0}, at: filename_create+0x62/0x190
[ 3437.454875]
               but task is already holding lock:
[ 3437.455268] ffffa0a02b2b10e0 (&type->s_umount_key#48){.+.+}-{3:3}, at: bch2_fs_file_ioctl+0x232/0xc90 [bcachefs]
[ 3437.456009]
               which lock already depends on the new lock.

[ 3437.456553]
               the existing dependency chain (in reverse order) is:
[ 3437.457054]
               -> #3 (&type->s_umount_key#48){.+.+}-{3:3}:
[ 3437.457507]        down_read+0x3e/0x170
[ 3437.457772]        bch2_fs_file_ioctl+0x232/0xc90 [bcachefs]
[ 3437.458206]        __x64_sys_ioctl+0x93/0xd0
[ 3437.458498]        do_syscall_64+0x42/0xf0
[ 3437.458779]        entry_SYSCALL_64_after_hwframe+0x6e/0x76
[ 3437.459155]
               -> #2 (&c->snapshot_create_lock){++++}-{3:3}:
[ 3437.459615]        down_read+0x3e/0x170
[ 3437.459878]        bch2_truncate+0x82/0x110 [bcachefs]
[ 3437.460276]        bchfs_truncate+0x254/0x3c0 [bcachefs]
[ 3437.460686]        notify_change+0x1f1/0x4a0
[ 3437.461283]        do_truncate+0x7f/0xd0
[ 3437.461555]        path_openat+0xa57/0xce0
[ 3437.461836]        do_filp_open+0xb4/0x160
[ 3437.462116]        do_sys_openat2+0x91/0xc0
[ 3437.462402]        __x64_sys_openat+0x53/0xa0
[ 3437.462701]        do_syscall_64+0x42/0xf0
[ 3437.462982]        entry_SYSCALL_64_after_hwframe+0x6e/0x76
[ 3437.463359]
               -> #1 (&sb->s_type->i_mutex_key#15){+.+.}-{3:3}:
[ 3437.463843]        down_write+0x3b/0xc0
[ 3437.464223]        bch2_write_iter+0x5b/0xcc0 [bcachefs]
[ 3437.464493]        vfs_write+0x21b/0x4c0
[ 3437.464653]        ksys_write+0x69/0xf0
[ 3437.464839]        do_syscall_64+0x42/0xf0
[ 3437.465009]        entry_SYSCALL_64_after_hwframe+0x6e/0x76
[ 3437.465231]
               -> #0 (sb_writers#10){.+.+}-{0:0}:
[ 3437.465471]        __lock_acquire+0x1455/0x21b0
[ 3437.465656]        lock_acquire+0xc6/0x2b0
[ 3437.465822]        mnt_want_write+0x46/0x1a0
[ 3437.465996]        filename_create+0x62/0x190
[ 3437.466175]        user_path_create+0x2d/0x50
[ 3437.466352]        bch2_fs_file_ioctl+0x2ec/0xc90 [bcachefs]
[ 3437.466617]        __x64_sys_ioctl+0x93/0xd0
[ 3437.466791]        do_syscall_64+0x42/0xf0
[ 3437.466957]        entry_SYSCALL_64_after_hwframe+0x6e/0x76
[ 3437.467180]
               other info that might help us debug this:

[ 3437.469670] 2 locks held by bcachefs/35533:
               other info that might help us debug this:

[ 3437.467507] Chain exists of:
                 sb_writers#10 --> &c->snapshot_create_lock --> &type->s_umount_key#48

[ 3437.467979]  Possible unsafe locking scenario:

[ 3437.468223]        CPU0                    CPU1
[ 3437.468405]        ----                    ----
[ 3437.468585]   rlock(&type->s_umount_key#48);
[ 3437.468758]                                lock(&c->snapshot_create_lock);
[ 3437.469030]                                lock(&type->s_umount_key#48);
[ 3437.469291]   rlock(sb_writers#10);
[ 3437.469434]
                *** DEADLOCK ***

[ 3437.469670] 2 locks held by bcachefs/35533:
[ 3437.469838]  #0: ffffa0a02ce00a88 (&c->snapshot_create_lock){++++}-{3:3}, at: bch2_fs_file_ioctl+0x1e3/0xc90 [bcachefs]
[ 3437.470294]  #1: ffffa0a02b2b10e0 (&type->s_umount_key#48){.+.+}-{3:3}, at: bch2_fs_file_ioctl+0x232/0xc90 [bcachefs]
[ 3437.470744]
               stack backtrace:
[ 3437.470922] CPU: 7 PID: 35533 Comm: bcachefs Kdump: loaded Tainted: G            E      6.7.0-rc7-custom+ #85
[ 3437.471313] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS Arch Linux 1.16.3-1-1 04/01/2014
[ 3437.471694] Call Trace:
[ 3437.471795]  <TASK>
[ 3437.471884]  dump_stack_lvl+0x57/0x90
[ 3437.472035]  check_noncircular+0x132/0x150
[ 3437.472202]  __lock_acquire+0x1455/0x21b0
[ 3437.472369]  lock_acquire+0xc6/0x2b0
[ 3437.472518]  ? filename_create+0x62/0x190
[ 3437.472683]  ? lock_is_held_type+0x97/0x110
[ 3437.472856]  mnt_want_write+0x46/0x1a0
[ 3437.473025]  ? filename_create+0x62/0x190
[ 3437.473204]  filename_create+0x62/0x190
[ 3437.473380]  user_path_create+0x2d/0x50
[ 3437.473555]  bch2_fs_file_ioctl+0x2ec/0xc90 [bcachefs]
[ 3437.473819]  ? lock_acquire+0xc6/0x2b0
[ 3437.474002]  ? __fget_files+0x2a/0x190
[ 3437.474195]  ? __fget_files+0xbc/0x190
[ 3437.474380]  ? lock_release+0xc5/0x270
[ 3437.474567]  ? __x64_sys_ioctl+0x93/0xd0
[ 3437.474764]  ? __pfx_bch2_fs_file_ioctl+0x10/0x10 [bcachefs]
[ 3437.475090]  __x64_sys_ioctl+0x93/0xd0
[ 3437.475277]  do_syscall_64+0x42/0xf0
[ 3437.475454]  entry_SYSCALL_64_after_hwframe+0x6e/0x76
[ 3437.475691] RIP: 0033:0x7f2743c313af
======================================================

In __bch2_ioctl_subvolume_create(), we grab s_umount unconditionally
and unlock it at the end of the function. There is a comment
"why do we need this lock?" about the lock coming from
commit 42d237320e98 ("bcachefs: Snapshot creation, deletion")
The reason is that __bch2_ioctl_subvolume_create() calls
sync_inodes_sb() which enforce locked s_umount to writeback all dirty
nodes before doing snapshot works.

Fix it by read locking s_umount for snapshotting only and unlocking
s_umount after sync_inodes_sb().

Signed-off-by: Su Yue <glass.su@suse.com>
Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>

bcachefs: kvfree bch_fs::snapshots in bch2_fs_snapshots_exit

bch_fs::snapshots is allocated by kvzalloc in __snapshot_t_mut.
It should be freed by kvfree not kfree.
Or umount will triger:

[  406.829178 ] BUG: unable to handle page fault for address: ffffe7b487148008
[  406.830676 ] #PF: supervisor read access in kernel mode
[  406.831643 ] #PF: error_code(0x0000) - not-present page
[  406.832487 ] PGD 0 P4D 0
[  406.832898 ] Oops: 0000 [#1] PREEMPT SMP PTI
[  406.833512 ] CPU: 2 PID: 1754 Comm: umount Kdump: loaded Tainted: G           OE      6.7.0-rc7-custom+ #90
[  406.834746 ] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS Arch Linux 1.16.3-1-1 04/01/2014
[  406.835796 ] RIP: 0010:kfree+0x62/0x140
[  406.836197 ] Code: 80 48 01 d8 0f 82 e9 00 00 00 48 c7 c2 00 00 00 80 48 2b 15 78 9f 1f 01 48 01 d0 48 c1 e8 0c 48 c1 e0 06 48 03 05 56 9f 1f 01 <48> 8b 50 08 48 89 c7 f6 c2 01 0f 85 b0 00 00 00 66 90 48 8b 07 f6
[  406.837810 ] RSP: 0018:ffffb9d641607e48 EFLAGS: 00010286
[  406.838213 ] RAX: ffffe7b487148000 RBX: ffffb9d645200000 RCX: ffffb9d641607dc4
[  406.838738 ] RDX: 000065bb00000000 RSI: ffffffffc0d88b84 RDI: ffffb9d645200000
[  406.839217 ] RBP: ffff9a4625d00068 R08: 0000000000000001 R09: 0000000000000001
[  406.839650 ] R10: 0000000000000001 R11: 000000000000001f R12: ffff9a4625d4da80
[  406.840055 ] R13: ffff9a4625d00000 R14: ffffffffc0e2eb20 R15: 0000000000000000
[  406.840451 ] FS:  00007f0a264ffb80(0000) GS:ffff9a4e2d500000(0000) knlGS:0000000000000000
[  406.840851 ] CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[  406.841125 ] CR2: ffffe7b487148008 CR3: 000000018c4d2000 CR4: 00000000000006f0
[  406.841464 ] Call Trace:
[  406.841583 ]  <TASK>
[  406.841682 ]  ? __die+0x1f/0x70
[  406.841828 ]  ? page_fault_oops+0x159/0x470
[  406.842014 ]  ? fixup_exception+0x22/0x310
[  406.842198 ]  ? exc_page_fault+0x1ed/0x200
[  406.842382 ]  ? asm_exc_page_fault+0x22/0x30
[  406.842574 ]  ? bch2_fs_release+0x54/0x280 [bcachefs]
[  406.842842 ]  ? kfree+0x62/0x140
[  406.842988 ]  ? kfree+0x104/0x140
[  406.843138 ]  bch2_fs_release+0x54/0x280 [bcachefs]
[  406.843390 ]  kobject_put+0xb7/0x170
[  406.843552 ]  deactivate_locked_super+0x2f/0xa0
[  406.843756 ]  cleanup_mnt+0xba/0x150
[  406.843917 ]  task_work_run+0x59/0xa0
[  406.844083 ]  exit_to_user_mode_prepare+0x197/0x1a0
[  406.844302 ]  syscall_exit_to_user_mode+0x16/0x40
[  406.844510 ]  do_syscall_64+0x4e/0xf0
[  406.844675 ]  entry_SYSCALL_64_after_hwframe+0x6e/0x76
[  406.844907 ] RIP: 0033:0x7f0a2664e4fb

Signed-off-by: Su Yue <glass.su@suse.com>
Reviewed-by: Brian Foster <bfoster@redhat.com>
Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>

bcachefs: bios must be 512 byte algined

Fixes: 023f9ac9f70f bcachefs: Delete dio read alignment check
Reported-by: Brian Foster <bfoster@redhat.com>
Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>

bcachefs: remove redundant variable tmp

The variable tmp is being assigned a value but it isn't being
read afterwards. The assignment is redundant and so tmp can be
removed.

Cleans up clang scan build warning:
warning: Although the value stored to 'ret' is used in the enclosing
expression, the value is never actually read from 'ret'
[deadcode.DeadStores]

Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Reviewed-by: Brian Foster <bfoster@redhat.com>
Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>

bcachefs: Improve trace_trans_restart_relock

Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>

bcachefs: Fix excess transaction restarts in __bchfs_fallocate()

drop_locks_do() should not be used in a fastpath without first trying
the do in nonblocking mode - the unlock and relock will cause excessive
transaction restarts and potentially livelocking with other threads that
are contending for the same locks.

Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>

bcachefs: extents_to_bp_state

Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>

bcachefs: bkey_and_val_eq()

Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>

bcachefs: Better journal tracepoints

Factor out bch2_journal_bufs_to_text(), and use it in the
journal_entry_full() tracepoint; when we can't get a journal reservation
we need to know the outstanding journal entry sizes to know if the
problem is due to excessive flushing.

Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>

bcachefs: Print size of superblock with space allocated

Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>

bcachefs: Avoid flushing the journal in the discard path

When issuing discards, we may need to flush the journal if there's too
many buckets that can't be discarded until a journal flush.

But the heuristic was bad; we should be comparing the number of buckets
that need to flushes against the number of free buckets, not the number
of buckets we saw.

Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>

bcachefs: Improve move_extent tracepoint

Also print out the data_opts, so that we can see what specifically is
being done to an extent.

Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>

bcachefs: Add missing bch2_moving_ctxt_flush_all()

This fixes a bug with rebalance IOs getting stuck with reads completed,
but writes never being issued.

Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>

bcachefs: Re-add move_extent_write tracepoint

It appears this was accidentally deleted at some point - also, do a bit
of cleanup.

Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>

bcachefs: bch2_kthread_io_clock_wait() no longer sleeps until full amount

Drop t he loop in bch2_kthread_io_clock_wait(): this allows the code
that uses it to be woken up for other reasons, and fixes a bug where
rebalance wouldn't wake up when a scan was requested.

This raises the possibility of spurious wakeups, but callers should
always be able to handle that reasonably well.

Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>

bcachefs: Add .val_to_text() for KEY_TYPE_cookie

Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>

bcachefs: Don't pass memcmp() as a pointer

Some (buggy!) compilers have issues with this.

Fixes: https://github.com/koverstreet/bcachefs/issues/625
Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>

Merge tag 'header_cleanup-2024-01-20' of https://evilpiepirate.org/git/bcachefs

Pull header fix from Kent Overstreet:
 "Just one small fixup for the RT build"

* tag 'header_cleanup-2024-01-20' of https://evilpiepirate.org/git/bcachefs:
  spinlock: Fix failing build for PREEMPT_RT

bcachefs: Reduce would_deadlock restarts

We don't have to take locks in any particular ordering - we'll make
forward progress just fine - but if we try to stick to an ordering, it
can help to avoid excessive would_deadlock transaction restarts.

This tweaks the reflink path to take extents btree locks in the right
order.

Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>

bcachefs: bch2_trans_account_disk_usage_change()

The disk space accounting rewrite is splitting out accounting for each
replicas set - those are moving to btree keys, instead of percpu
counters.

This breaks bch2_trans_fs_usage_apply() up, splitting out the part we
will still need.

Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>

bcachefs: bch_fs_usage_base

Split out base filesystem usage into its own type; prep work for
breaking up bch2_trans_fs_usage_apply().

Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>

bcachefs: bch2_prt_compression_type()

bounds checking helper, since compression types are extensible

Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>

bcachefs: helpers for printing data types

We need bounds checking since new versions may introduce new data types.

Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>

bcachefs: BTREE_TRIGGER_ATOMIC

Add a new flag to be explicit about when we're running atomic triggers.

Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>

bcachefs: drop to_text code for obsolete bps in alloc keys

Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>

bcachefs: eytzinger_for_each() declares loop iter

Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>

bcachefs: Don't log errors if BCH_WRITE_ALLOC_NOWAIT

Previously, we added logging in the write path to ensure that any
unexpected errors getting reported to userspace have a log message; but
BCH_WRITE_ALLOC_NOWAIT is a special case, it's used for promotes where
errors are expected and not reported out to userspace - so we need to
silence those.

Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>

bcachefs: fix memleak in bch2_split_devs

The pointer dev_name can be modified by strseq(),
then causes the memleak:

unreferenced object 0xffff9d08a2916c80 (size 32):
  comm "mount.bcachefs", pid 9090, jiffies 4295856224 (age 17.564s)
  hex dump (first 32 bytes):
    2f 64 65 76 2f 6d 61 70 70 65 72 2f 74 65 73 74  /dev/mapper/test
    2d 30 00 00 00 00 00 00 00 00 00 00 00 00 00 00  -0..............
  backtrace:
    [<00000000c5d3be7d>] __kmem_cache_alloc_node+0x1f3/0x2c0
    [<0000000052215d26>] __kmalloc_node_track_caller+0x51/0x150
    [<0000000069fea956>] kstrdup+0x32/0x60
    [<000000000877fcf1>] bch2_split_devs+0x3f/0x150 [bcachefs]
    [<000000007ee93204>] bch2_mount+0xcb/0x640 [bcachefs]
    [<000000002dd1e04b>] legacy_get_tree+0x30/0x60
    [<000000006afc31d3>] vfs_get_tree+0x28/0xf0
    [<000000007b0c538e>] path_mount+0x475/0xb60
    [<0000000092de5882>] __x64_sys_mount+0x105/0x140
    [<0000000054fc05d8>] do_syscall_64+0x42/0xf0
    [<00000000df584910>] entry_SYSCALL_64_after_hwframe+0x6e/0x76

Fix it by copy pointer dev_name at beginning and free the copied
pointer at end.

Signed-off-by: Su Yue <glass.su@suse.com>
Reviewed-by: Brian Foster <bfoster@redhat.com>
Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>

Merge tag 'v6.8-rc-part2-smb-client' of git://git.samba.org/sfrench/cifs-2.6

Pull smb client updates from Steve French:
 "Various smb client fixes, including multichannel and for SMB3.1.1
  POSIX extensions:

   - debugging improvement (display start time for stats)

   - two reparse point handling fixes

   - various multichannel improvements and fixes

   - SMB3.1.1 POSIX extensions open/create parsing fix

   - retry (reconnect) improvement including new retrans mount parm, and
     handling of two additional return codes that need to be retried on

   - two minor cleanup patches and another to remove duplicate query
     info code

   - two documentation cleanup, and one reviewer email correction"

* tag 'v6.8-rc-part2-smb-client' of git://git.samba.org/sfrench/cifs-2.6:
  cifs: update iface_last_update on each query-and-update
  cifs: handle servers that still advertise multichannel after disabling
  cifs: new mount option called retrans
  cifs: reschedule periodic query for server interfaces
  smb: client: don't clobber ->i_rdev from cached reparse points
  smb: client: get rid of smb311_posix_query_path_info()
  smb: client: parse owner/group when creating reparse points
  smb: client: fix parsing of SMB3.1.1 POSIX create context
  cifs: update known bugs mentioned in kernel docs for cifs
  cifs: new nt status codes from MS-SMB2
  cifs: pick channel for tcon and tdis
  cifs: open_cached_dir should not rely on primary channel
  smb3: minor documentation updates
  Update MAINTAINERS email address
  cifs: minor comment cleanup
  smb3: show beginning time for per share stats
  cifs: remove redundant variable tcon_exist

Merge tag 'dmaengine-fix-6.8-rc1' of git://git./linux/kernel/git/vkoul/dmaengine

Pull dmaengine updates from Vinod Koul:
 "New support:
   - Loongson LS2X APB DMA controller
   - sf-pdma: mpfs-pdma support
   - Qualcomm X1E80100 GPI dma controller support

  Updates:
   - Xilinx XDMA updates to support interleaved DMA transfers
   - TI PSIL threads for AM62P and J722S and cfg register regions
     description
   - axi-dmac Improving the cyclic DMA transfers
   - Tegra Support dma-channel-mask property
   - Remaining platform remove callback returning void conversions

 Driver fixes for:
   - Xilinx xdma driver operator precedence and initialization fix
   - Excess kernel-doc warning fix in imx-sdma xilinx xdma drivers
   - format-overflow warning fix for rz-dmac, sh usb dmac drivers
   - 'output may be truncated' fix for shdma, fsl-qdma and dw-edma
     drivers"

* tag 'dmaengine-fix-6.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/vkoul/dmaengine: (58 commits)
  dmaengine: dw-edma: increase size of 'name' in debugfs code
  dmaengine: fsl-qdma: increase size of 'irq_name'
  dmaengine: shdma: increase size of 'dev_id'
  dmaengine: xilinx: xdma: Fix kernel-doc warnings
  dmaengine: usb-dmac: Avoid format-overflow warning
  dmaengine: sh: rz-dmac: Avoid format-overflow warning
  dmaengine: imx-sdma: fix Excess kernel-doc warnings
  dmaengine: xilinx: xdma: Fix initialization location of desc in xdma_channel_isr()
  dmaengine: xilinx: xdma: Fix operator precedence in xdma_prep_interleaved_dma()
  dmaengine: xilinx: xdma: statify xdma_prep_interleaved_dma
  dmaengine: xilinx: xdma: Workaround truncation compilation error
  dmaengine: pl330: issue_pending waits until WFP state
  dmaengine: xilinx: xdma: Implement interleaved DMA transfers
  dmaengine: xilinx: xdma: Prepare the introduction of interleaved DMA transfers
  dmaengine: xilinx: xdma: Add transfer error reporting
  dmaengine: xilinx: xdma: Add error checking in xdma_channel_isr()
  dmaengine: xilinx: xdma: Rework xdma_terminate_all()
  dmaengine: xilinx: xdma: Ease dma_pool alignment requirements
  dmaengine: xilinx: xdma: Add necessary macro definitions
  dmaengine: xilinx: xdma: Get rid of unused code
  ...

Merge tag 'coccinelle-for-6.8' of git://git./linux/kernel/git/jlawall/linux

Pull coccinelle updates from Julia Lawall:
 "Updates to the device_attr_show semantic patch to reflect the new
  guidelines of the Linux kernel documentation.

  The problem was identified by Li Zhijian <lizhijian@fujitsu.com>, who
  proposed an initial fix"

* tag 'coccinelle-for-6.8' of git://git.kernel.org/pub/scm/linux/kernel/git/jlawall/linux:
  coccinelle: device_attr_show: simplify patch case
  coccinelle: device_attr_show: Adapt to the latest Documentation/filesystems/sysfs.rst

media: solo6x10: replace max(a, min(b, c)) by clamp(b, a, c)

This patch replaces max(a, min(b, c)) by clamp(b, a, c) in the solo6x10
driver.  This improves the readability and more importantly, for the
solo6x10-p2m.c file, this reduces on my system (x86-64, gcc 13):

 - the preprocessed size from 121 MiB to 4.5 MiB;

 - the build CPU time from 46.8 s to 1.6 s;

 - the build memory from 2786 MiB to 98MiB.

In fine, this allows this relatively simple C file to be built on a
32-bit system.

Reported-by: Jiri Slaby <jirislaby@gmail.com>
Closes: https://lore.kernel.org/lkml/18c6df0d-45ed-450c-9eda-95160a2bbb8e@gmail.com/
Cc: <stable@vger.kernel.org> # v6.7+
Suggested-by: David Laight <David.Laight@ACULAB.COM>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Reviewed-by: David Laight <David.Laight@ACULAB.COM>
Reviewed-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

coccinelle: device_attr_show: simplify patch case

Replacing the final expression argument by ... allows the format
string to have multiple arguments.

It also has the advantage of allowing the change to be recognized as
a change in a single statement, thus avoiding adding unneeded braces.

Signed-off-by: Julia Lawall <Julia.Lawall@inria.fr>

execve: open the executable file before doing anything else

No point in allocating a new mm, counting arguments and environment
variables etc if we're just going to return ENOENT.

This patch does expose the fact that 'do_filp_open()' that execve() uses
is still unnecessarily expensive in the failure case, because it
allocates the 'struct file *' early, even if the path lookup (which is
heavily optimized) fails.

So that remains an unnecessary cost in the "no such executable" case,
but it's a separate issue.  Regardless, I do not want to do _both_ a
filename_lookup() and a later do_filp_open() like the origin patch by
Josh Triplett did in [1].

Reported-by: Josh Triplett <josh@joshtriplett.org>
Cc: Kees Cook <keescook@chromium.org>
Cc: Mateusz Guzik <mjguzik@gmail.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Link: https://lore.kernel.org/lkml/5c7333ea4bec2fad1b47a8fa2db7c31e4ffc4f14.1663334978.git.josh@joshtriplett.org/
Link: https://lore.kernel.org/lkml/202209161637.9EDAF6B18@keescook/
Link: https://lore.kernel.org/lkml/CAHk-=wgznerM-xs+x+krDfE7eVBiy_HOam35rbsFMMOwvYuEKQ@mail.gmail.com/
Link: https://lore.kernel.org/lkml/CAHk-=whf9qLO8ipps4QhmS0BkM8mtWJhvnuDSdtw5gFjhzvKNA@mail.gmail.com/
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Merge tag 'riscv-for-linus-6.8-mw4' of git://git./linux/kernel/git/riscv/linux

Pull more RISC-V updates from Palmer Dabbelt:

 - Support for tuning for systems with fast misaligned accesses.

 - Support for SBI-based suspend.

 - Support for the new SBI debug console extension.

 - The T-Head CMOs now use PA-based flushes.

 - Support for enabling the V extension in kernel code.

 - Optimized IP checksum routines.

 - Various ftrace improvements.

 - Support for archrandom, which depends on the Zkr extension.

 - The build is no longer broken under NET=n, KUNIT=y for ports that
   don't define their own ipv6 checksum.

* tag 'riscv-for-linus-6.8-mw4' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux: (56 commits)
  lib: checksum: Fix build with CONFIG_NET=n
  riscv: lib: Check if output in asm goto supported
  riscv: Fix build error on rv32 + XIP
  riscv: optimize ELF relocation function in riscv
  RISC-V: Implement archrandom when Zkr is available
  riscv: Optimize hweight API with Zbb extension
  riscv: add dependency among Image(.gz), loader(.bin), and vmlinuz.efi
  samples: ftrace: Add RISC-V support for SAMPLE_FTRACE_DIRECT[_MULTI]
  riscv: ftrace: Add DYNAMIC_FTRACE_WITH_DIRECT_CALLS support
  riscv: ftrace: Make function graph use ftrace directly
  riscv: select FTRACE_MCOUNT_USE_PATCHABLE_FUNCTION_ENTRY
  lib/Kconfig.debug: Update AS_HAS_NON_CONST_LEB128 comment and name
  riscv: Restrict DWARF5 when building with LLVM to known working versions
  riscv: Hoist linker relaxation disabling logic into Kconfig
  kunit: Add tests for csum_ipv6_magic and ip_fast_csum
  riscv: Add checksum library
  riscv: Add checksum header
  riscv: Add static key for misaligned accesses
  asm-generic: Improve csum_fold
  RISC-V: selftests: cbo: Ensure asm operands match constraints
  ...

Merge tag 'scsi-misc' of git://git./linux/kernel/git/jejb/scsi

Pull SCSI updates from James Bottomley:
 "Final round of fixes that came in too late to send in the first
  request.

  It's nine bug fixes and one version update (because of a bug fix) and
  one set of PCI ID additions. There's one bug fix in the core which is
  really a one liner (except that an additional sdev pointer was added
  for convenience) and the rest are in drivers"

* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
  scsi: target: core: Add TMF to tmr_list handling
  scsi: core: Kick the requeue list after inserting when flushing
  scsi: fnic: unlock on error path in fnic_queuecommand()
  scsi: fcoe: Fix unsigned comparison with zero in store_ctlr_mode()
  scsi: mpi3mr: Fix mpi3mr_fw.c kernel-doc warnings
  scsi: smartpqi: Bump driver version to 2.1.26-030
  scsi: smartpqi: Fix logical volume rescan race condition
  scsi: smartpqi: Add new controller PCI IDs
  scsi: ufs: qcom: Remove unnecessary goto statement from ufs_qcom_config_esi()
  scsi: ufs: core: Remove the ufshcd_hba_exit() call from ufshcd_async_scan()
  scsi: ufs: core: Simplify power management during async scan

Merge tag 'sh-for-v6.8-tag1' of git://git./linux/kernel/git/glaubitz/sh-linux

Pull sh updates from John Paul Adrian Glaubitz:
 "Since the large patch series to convert arch/sh to device tree support
  has not been finalized yet due to various maintainers still asking for
  changes to the series, this ended up being rather small consisting of
  just two fixes.

  The first patch by Geert Uytterhoeven addresses a build failure in the
  EcoVec platform code. And the second patch by Masahiro Yamada removes
  an unnecessary $(foreach ...) found in a Makefile of the vsyscall
  code.

   - Rename missed backlight field from fbdev to dev

   - Remove unnecessary $(foreach ...)"

* tag 'sh-for-v6.8-tag1' of git://git.kernel.org/pub/scm/linux/kernel/git/glaubitz/sh-linux:
  sh: vsyscall: Remove unnecessary $(foreach ...)
  sh: ecovec24: Rename missed backlight field from fbdev to dev