arm64: dts: qcom: sm8550: Fix SPMI channels size

The actual size of the channels registers region is 4MB, according to the
documentation. This issue was not caught until now because the driver was
supposed to allow same regions being mapped multiple times for supporting
multiple buses. Thie driver is using platform_get_resource_byname() and
devm_ioremap() towards that purpose, which intentionally avoids
devm_request_mem_region() altogether.

Fixes: ffc50b2d3828 ("arm64: dts: qcom: Add base SM8550 dtsi")
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on SM8550-QRD
Link: https://lore.kernel.org/r/20240221-dts-qcom-sm8550-fix-spmi-chnls-size-v2-1-72b5efd9dc4f@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>

arm64: dts: qcom: sm6115: fix USB PHY configuration

The patch adding Type-C support for sm6115 was misapplied. All the
orientation switch configuration ended up at the UFS PHY node instead of
the USB PHY node. Move the data bits to the correct place.

Fixes: a06a2f12f9e2 ("arm64: dts: qcom: qrb4210-rb2: enable USB-C port handling")
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20240220173104.3052778-1-dmitry.baryshkov@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>

arm64: dts: sm8650: Add msi-map-mask for PCIe nodes

"msi-map-mask" is a required property for all Qcom PCIe controllers as it
would allow all PCIe devices under a bus to share the same MSI identifier.

Without this property, each device has to use a separate MSI identifier
which is not possible due to platform limitations.

Currently, this is not an issue since only one device is connected to the
bus on boards making use of this SoC.

Fixes: a33a532b3b1e ("arm64: dts: qcom: sm8650: Use GIC-ITS for PCIe0 and PCIe1")
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20240216-sm8550-msi-map-fix-v1-1-b66d83ce48b7@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>

arm64: dts: qcom: replace underscores in node names

Underscores should not be used in node names (dtc with W=2 warns about
them), so replace them with hyphens.

Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20240213145124.342514-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>

dt-bindings: arm: qcom: Add Samsung Galaxy Tab 4 10.1 LTE

This documents Samsung Galaxy Tab 4 10.1 LTE (samsung,matisselte)
which is a tablet by Samsung based on the MSM8926 SoC.

Signed-off-by: Stefan Hansson <newbyte@postmarketos.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20240215180322.99089-3-newbyte@postmarketos.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>

arm64: dts: qcom: pm4125: define USB-C related blocks

Define VBUS regulator and the Type-C handling block as present on the
Quacomm PM4125 PMIC.

Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Link: https://lore.kernel.org/r/20240202-pm4125-typec-v2-3-12771d85700d@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>

arm64: dts: qcom: sa8540p-ride: disable pcie2a node

pcie2a and pcie3a both cause interrupt storms to occur. However, when
both are enabled simultaneously, the two combined interrupt storms will
lead to rcu stalls. Red Hat is the only company still using this board
and since we still need pcie3a, just disable pcie2a.

Signed-off-by: Lucas Karpinski <lkarpins@redhat.com>
Reviewed-by: Brian Masney <bmasney@redhat.com>
Link: https://lore.kernel.org/r/qcoqksikfvdqxk6stezbzc7l2br37ccgqswztzqejmhrkhbrwt@ta4npsm35mqk
Signed-off-by: Bjorn Andersson <andersson@kernel.org>

arm64: dts: qcom: sc7280: add slimbus DT node

Populate the DTSI node for slimbus instance to be
used by bluetooth FM audio case.

Signed-off-by: Viken Dadhaniya <quic_vdadhani@quicinc.com>
Link: https://lore.kernel.org/r/20240215090910.30021-1-quic_vdadhani@quicinc.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>

arm64: dts: qcom: sc7280: Add capacity and DPC properties

The "capacity-dmips-mhz" and "dynamic-power-coefficient" are
used to build Energy Model which in turn is used by EAS to take
placement decisions. So add it to SC7280 soc.

Signed-off-by: Ankit Sharma <quic_anshar@quicinc.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20231103105440.23904-1-quic_anshar@quicinc.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>

arm64: dts: qcom: pmi632: Add PBS client and use in LPG node

With SDAM + PBS the LPG driver can configure the LED pattern in
hardware.

Signed-off-by: Luca Weiss <luca.weiss@fairphone.com>
Link: https://lore.kernel.org/r/20240205-pmi632-ppg-v1-2-e236c95a2099@fairphone.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>

arm64: dts: qcom: sm8550: Use GIC-ITS for PCIe0 and PCIe1

Both PCIe0 and PCIe1 controllers are capable of signalling the MSIs
received from endpoint devices to the CPU using GIC-ITS MSI controller.
Add support for it.

The GIC-ITS MSI implementation provides an advantage over internal MSI
implementation using Locality-specific Peripheral Interrupts (LPI) that
would allow MSIs to be targeted for each CPU core.

Like SM8450, the IDs are swapped, but works fine on PCIe0 and PCIe1.

WiFi PCIe Device on SM8550-QRD using GIC-ITS:
218:          0          4          0          0          0          0          0          0   ITS-MSI 524288 Edge      bhi
219:          0          0          5          0          0          0          0          0   ITS-MSI 524289 Edge      mhi
220:          0          0          0         33          0          0          0          0   ITS-MSI 524290 Edge      mhi
221:          0          0          0          0          3          0          0          0   ITS-MSI 524291 Edge      ce0
222:          0          0          0          0          0          1          0          0   ITS-MSI 524292 Edge      ce1
223:          0          0          0          0          0          0         38          0   ITS-MSI 524293 Edge      ce2
224:          0          0          0          0          0          0          0         31   ITS-MSI 524294 Edge      ce3
225:          0          0          0          0          0          0          0          0   ITS-MSI 524295 Edge      ce5
226:          0          0          0          0          0          0          0          0   ITS-MSI 524296 Edge      DP_EXT_IRQ
227:          0          0          0          0          0          0          0          0   ITS-MSI 524297 Edge      DP_EXT_IRQ
228:          0          0          0          0          0          0          0          0   ITS-MSI 524298 Edge      DP_EXT_IRQ
229:          0          0          0          0          0          0          0          0   ITS-MSI 524299 Edge      DP_EXT_IRQ
230:          0          0          0          0          0          0          0          0   ITS-MSI 524300 Edge      DP_EXT_IRQ
231:          0          0          0          0          0          0          0          0   ITS-MSI 524301 Edge      DP_EXT_IRQ
232:          0          0          0          0          0          0          0          0   ITS-MSI 524302 Edge      DP_EXT_IRQ

NVMe in SM8550-HDK M.2 Slot using GIC-ITS:
212:          0          0         22          0          0          0          0          0   ITS-MSI 134742016 Edge      nvme0q0
213:     133098          0          0          0          0          0          0          0   ITS-MSI 134742017 Edge      nvme0q1
214:          0     139450          0          0          0          0          0          0   ITS-MSI 134742018 Edge      nvme0q2
215:          0          0     139476          0          0          0          0          0   ITS-MSI 134742019 Edge      nvme0q3
216:          0          0          0      69767          0          0          0          0   ITS-MSI 134742020 Edge      nvme0q4
217:          0          0          0          0      80368          0          0          0   ITS-MSI 134742021 Edge      nvme0q5
218:          0          0          0          0          0      77315          0          0   ITS-MSI 134742022 Edge      nvme0q6
219:          0          0          0          0          0          0      73022          0   ITS-MSI 134742023 Edge      nvme0q7
220:          0          0          0          0          0          0          0     329993   ITS-MSI 134742024 Edge      nvme0q8

Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20240122-topic-sm8550-upstream-pcie-its-v2-1-b3398d86d1f1@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>

arm64: dts: qcom: sm8150: correct PCIe wake-gpios

Bindings allow a "wake", not "enable", GPIO.  Schematics also use WAKE
name for the pin:

  sa8155p-adp.dtb: pcie@1c00000: Unevaluated properties are not allowed ('enable-gpio' was unexpected)

Fixes: a1c86c680533 ("arm64: dts: qcom: sm8150: Add PCIe nodes")
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20240108131216.53867-2-krzysztof.kozlowski@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>

arm64: dts: qcom: sdm845-db845c: correct PCIe wake-gpios

Bindings allow a "wake", not "enable", GPIO.  Schematics also use WAKE
name for the pin:

  sdm845-db845c.dtb: pcie@1c00000: Unevaluated properties are not allowed ('enable-gpio' was unexpected)

Fixes: 4a657c264b78 ("arm64: dts: qcom: db845c: Enable PCIe controllers")
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20240108131216.53867-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>

arm64: dts: qcom: sm7225-fairphone-fp4: Enable display and GPU

Add the description for the display panel found on this phone.
Unfortunately the LCDB module on PM6150L isn't yet supported upstream so
we need to use a dummy regulator-fixed in the meantime.

And with this done we can also enable the GPU and set the zap shader
firmware path.

Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Luca Weiss <luca.weiss@fairphone.com>
Link: https://lore.kernel.org/r/20240216-fp4-panel-v3-4-a556e4b79640@fairphone.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>

arm64: dts: qcom: sm6350: Remove "disabled" state of GMU

The GMU won't probe without GPU being enabled, so we can remove the
disabled status so we don't have to explicitly enable the GMU in all the
devices that enable GPU.

Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Luca Weiss <luca.weiss@fairphone.com>
Link: https://lore.kernel.org/r/20240216-fp4-panel-v3-3-a556e4b79640@fairphone.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>

arm64: dts: qcom: msm8916-samsung-fortuna/rossa: Add fuel gauge

Like the Samsung Galaxy A3/A5, the Grand Prime/Core Prime uses a
Richtek RT5033 PMIC as battery fuel gauge, charger, flash LED and for some
regulators.
For now, only add the fuel gauge/battery device to the device tree, so we
can check the remaining battery percentage.

The other RT5033 drivers need some more work first before they can be used
properly.

Signed-off-by: Joe Mason <buddyjojo06@outlook.com>
[Raymond: Move to fortuna-common. Use interrupts-extended]
Signed-off-by: Raymond Hackley <raymondhackley@protonmail.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20240216124639.24689-1-raymondhackley@protonmail.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>

arm64: dts: qcom: sm6350: Add interconnect for MDSS

Add the definition for the interconnect used in the display subsystem.

Signed-off-by: Luca Weiss <luca.weiss@fairphone.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20240216-sm6350-interconnect-v1-1-9d55667c06ca@fairphone.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>

arm64: dts: qcom: msm8916-samsung-fortuna/rossa: Add initial device trees

Samsung Galaxy Core Prime and Grand Prime are phones based on MSM8916.
They are similar to the other Samsung devices based on MSM8916 with only a
few minor differences.

This initial commit adds support for:
 - fortuna3g (SM-G530H)
 - gprimeltecan (SM-G530W)
 - grandprimelte (SM-G530FZ)
 - rossa (SM-G360G)

The device trees contain initial support with:
 - GPIO keys
 - Regulator haptic
 - SDHCI (internal and external storage)
 - USB Device Mode
 - UART (on USB connector via the SM5502/SM5504 MUIC)
 - WCNSS (WiFi/BT)
 - Regulators
 - QDSP6 audio
 - Speaker/earpiece/headphones/microphones via digital/analog codec in
   MSM8916/PM8916
 - WWAN Internet via BAM-DMUX

There are different variants of Core Prime and Grand Prime, with some
differences in accelerometer, NFC and panel.
Core Prime and Grand Prime are similar, with some differences in MUIC,
panel and touchscreen.

The common parts are shared in
msm8916-samsung-fortuna-common.dtsi and msm8916-samsung-rossa-common.dtsi
to reduce duplication.

Signed-off-by: Walter Broemeling <wallebroem@gmail.com>
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
[Joe: Add audio, buttons and WiFi]
Signed-off-by: Joe Mason <buddyjojo06@outlook.com>
[Siddharth: Add fortuna3g]
Signed-off-by: Siddharth Manthan <siddharth.manthan@gmail.com>
[Raymond: Add modem, fortuna-common.dtsi, grandprimelte and rossa]
Signed-off-by: Raymond Hackley <raymondhackley@protonmail.com>
Link: https://lore.kernel.org/r/20240129143147.5058-1-raymondhackley@protonmail.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>

arm64: dts: qcom: sm8550: Switch UFS from opp-table-hz to opp-v2

Now that the non-legacy form of OPP is supported within the UFS driver,
go ahead and switch to it, adding support for more intermediate freq/power
states.

Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on SM8550-QRD
Link: https://lore.kernel.org/r/20240203-topic-8550_ufs_oppv2-v2-1-b0bef2a73e6c@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>

arm64: dts: qcom: sc8180x: describe all PCI MSI interrupts

Each group of MSI interrupts is mapped to the separate host interrupt.
Describe each of interrupts in the device tree for PCIe hosts.  This
also corrects PCIe1 and PCIe2 first MSI interrupt.

Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Tested-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20240205163123.81842-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>

arm64: dts: qcom: minor whitespace cleanup

The DTS code coding style expects exactly one space before '{' and
around '=' characters.

Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20240208105208.128706-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>

arm64: dts: qcom: ssm7125-xiaomi: drop incorrect UFS phy max current

Neither bindings nor UFS phy driver use properties like
'vdda-phy-max-microamp' and 'vdda-pll-max-microamp':

  sm7125-xiaomi-curtana.dtb: phy@1d87000: 'vdda-phy-max-microamp', 'vdda-pll-max-microamp' do not match any of the regexes: 'pinctrl-[0-9]+'

Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20240212150558.81896-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>

arm64: dts: qcom: x1e80100-crd: add sound card

Add sound card to X1E80100-CRD board and update DMIC supply.  Works so
far:
 - Audio playback via speakers or audio jack headset,
 - DMIC0-3 recording.

Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20240212184403.246299-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>

arm64: dts: x1e80100: correct DMIC2 and DMIC3 pin config node names

Correct the TLMM pin configuration and muxing node names used for DMIC2
and DMIC3 (dmic01 -> dmic23).  This has no functional impact, but
improves code readability and avoids any confusion when reading the DTS.

Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20240212172335.124845-5-krzysztof.kozlowski@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>

arm64: dts: sm8650: correct DMIC2 and DMIC3 pin config node names

Correct the TLMM pin configuration and muxing node names used for DMIC2
and DMIC3 (dmic01 -> dmic23).  This has no functional impact, but
improves code readability and avoids any confusion when reading the DTS.

Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20240212172335.124845-4-krzysztof.kozlowski@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>

arm64: dts: sm8550: correct DMIC2 and DMIC3 pin config node names

Correct the TLMM pin configuration and muxing node names used for DMIC2
and DMIC3 (dmic01 -> dmic23).  This has no functional impact, but
improves code readability and avoids any confusion when reading the DTS.

Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20240212172335.124845-3-krzysztof.kozlowski@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>

arm64: dts: sm8450: correct DMIC2 and DMIC3 pin config node names

Correct the TLMM pin configuration and muxing node names used for DMIC2
and DMIC3 (dmic01 -> dmic23).  This has no functional impact, but
improves code readability and avoids any confusion when reading the DTS.

Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20240212172335.124845-2-krzysztof.kozlowski@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>

arm64: dts: sc8280xp: correct DMIC2 and DMIC3 pin config node names

Correct the TLMM pin configuration and muxing node names used for DMIC2
and DMIC3 (dmic01 -> dmic23).  This has no functional impact, but
improves code readability and avoids any confusion when reading the DTS.

Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20240212172335.124845-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>

arm64: dts: qcom: sdm845: Enable cros-ec-spi as wake source

The cros_ec driver currently assumes that cros-ec-spi compatible device
nodes are a wakeup-source even though the wakeup-source property is not
defined.

Some Chromebooks use a separate wake pin, while others overload the
interrupt for wake and IO. With the current assumption, spurious wakes
can occur on systems that use a separate wake pin. It is planned to
update the driver to no longer assume that the EC interrupt pin should
be enabled for wake.

Add the wakeup-source property to all cros-ec-spi compatible device
nodes to signify to the driver that they should still be a valid wakeup
source.

Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Mark Hasemeyer <markhas@chromium.org>
Link: https://lore.kernel.org/r/20240102140734.v4.16.I870e2c3490e7fc27a8f6bc41dba23b3dfacd2d13@changeid
Signed-off-by: Bjorn Andersson <andersson@kernel.org>

arm64: dts: qcom: sc7280: Enable cros-ec-spi as wake source

The cros_ec driver currently assumes that cros-ec-spi compatible device
nodes are a wakeup-source even though the wakeup-source property is not
defined.

Some Chromebooks use a separate wake pin, while others overload the
interrupt for wake and IO. With the current assumption, spurious wakes
can occur on systems that use a separate wake pin. It is planned to
update the driver to no longer assume that the EC interrupt pin should
be enabled for wake.

Add the wakeup-source property to all cros-ec-spi compatible device
nodes to signify to the driver that they should still be a valid wakeup
source.

Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Mark Hasemeyer <markhas@chromium.org>
Link: https://lore.kernel.org/r/20240102140734.v4.15.I7ea3f53272c9b7cd77633adfd18058ba443eed96@changeid
Signed-off-by: Bjorn Andersson <andersson@kernel.org>

arm64: dts: qcom: sc7180: Enable cros-ec-spi as wake source

The cros_ec driver currently assumes that cros-ec-spi compatible device
nodes are a wakeup-source even though the wakeup-source property is not
defined.

Some Chromebooks use a separate wake pin, while others overload the
interrupt for wake and IO. With the current assumption, spurious wakes
can occur on systems that use a separate wake pin. It is planned to
update the driver to no longer assume that the EC interrupt pin should
be enabled for wake.

Add the wakeup-source property to all cros-ec-spi compatible device
nodes to signify to the driver that they should still be a valid wakeup
source.

Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Mark Hasemeyer <markhas@chromium.org>
Link: https://lore.kernel.org/r/20240102140734.v4.14.I2ee94aede9e25932f656c2bdb832be3199fa1291@changeid
Signed-off-by: Bjorn Andersson <andersson@kernel.org>

arm64: dts: qcom: sdm845: Use the Low Power Island CX/MX for SLPI

The SLPI is powered by the Low Power Island power rails. Fix the incorrect
assignment.

Fixes: 74588aada59a ("arm64: dts: qcom: sdm845: add SLPI remoteproc")
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20231220-topic-sdm845_slpi_lcxmx-v1-1-db7c72ef99ae@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>

arm64: dts: qcom: msm8996: Define UFS UniPro clock limits

These limits were always defined as 0, but that didn't cause any issue
since the driver had hardcoded limits. In commit b4e13e1ae95e ("scsi: ufs:
qcom: Add multiple frequency support for MAX_CORE_CLK_1US_CYCLES") the
hardcoded limits were removed and the driver started reading them from DT,
causing UFS to stop working on MSM8996. Add real UniPro clock limits to fix
UFS.

Signed-off-by: Yassine Oudjana <y.oudjana@protonmail.com>
Fixes: 57fc67ef0d35 ("arm64: dts: qcom: msm8996: Add ufs related nodes")
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20231218133917.78770-1-y.oudjana@protonmail.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>

arm64: dts: qcom: qcs6490-rb3gen2: Declare GCC clocks protected

The SC7280 GCC binding describes clocks which, due to the difference in
security model, are not accessible on the RB3gen2 - in the same way seen
on QCM6490.

Mark these clocks as protected, to allow the board to boot. In contrast
to the present QCM6490 boards GCC_EDP_CLKREF_EN is left out, as this
does not need to be "protected" and is used on the RB3Gen2 board.

Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Luca Weiss <luca.weiss@fairphone.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <quic_bjorande@quicinc.com>
Link: https://lore.kernel.org/r/20240209-qcm6490-gcc-protected-clocks-v2-1-11cd5fc13bd0@quicinc.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>

arm64: dts: qcom: sc8280xp-pmics: Define adc for temp-alarms

sc8280xp-pmics define the two thermal zones "pm8280-1-thermal" and
"pm8280-2-thermal", but the related temp-alarm instances are not tied to
any adc channels, and as such continuously report the bogus temperature
of 37C.

After previously defining these adc channels across all boards using
sc8280xp-pmics.dtsi, we can now add these references.

This does however mean that we have a non-disabled node referencing
default-disabled nodes, requiring each board to enable the pmk8280_vadc.
Avoid this by marking pmk8280_vadc okay.

Signed-off-by: Bjorn Andersson <quic_bjorande@quicinc.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20240210-sc8280xp-pmic-thermal-v1-2-a1c215a17d10@quicinc.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>

arm64: dts: qcom: sc8280xp-crd: Add PMIC die-temp vadc channels

The die-temp vadc channels are not defined for the CRD, but describing
them directly would directly duplicate the definition from the Lenovo
Thinkpad X13s DeviceTree.

The sc8280xp-pmics file describes the common configuration of PMK8280,
two PMC8280, PMC8280C, and PMR735a. As such, even though these vadc
channels makes references across PMICs, it's suitable to define them in
the shared file.

Do this, and enable the pmk8280 vadc for the CRD.

Signed-off-by: Bjorn Andersson <quic_bjorande@quicinc.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20240210-sc8280xp-pmic-thermal-v1-1-a1c215a17d10@quicinc.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>

arm64: dts: qcom: qrb4210-rb2: enable USB-C port handling

Plug in USB-C related bits and pieces to enable USB role switching and
USB-C orientation handling for the Qualcomm RB2 board.

Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20240130-pmi632-typec-v3-6-b05fe44f0a51@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>

arm64: dts: qcom: sm6115: drop pipe clock selection

Stop selecting UTMI clock as the USB3 PIPE clock. This setting is
incompatible with the USB host working in USB3 (SuperSpeed) mode.
While we are at it, also drop the default setting for the port speed.

Fixes: 9dd5f6dba729 ("arm64: dts: qcom: sm6115: Add USB SS qmp phy node")
Signed-off-by: Vladimir Zapolskiy <vladimir.zapolskiy@linaro.org>
[DB: fixed commit message, dropped dr_mode setting]
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Tested-by: Luca Weiss <luca.weiss@fairphone.com> # sdm632-fairphone-fp3
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20240130-pmi632-typec-v3-5-b05fe44f0a51@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>

arm64: dts: qcom: pmi632: define USB-C related blocks

Define VBUS regulator and the Type-C handling block as present on the
Quacomm PMI632 PMIC.

Reviewed-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Tested-by: Luca Weiss <luca.weiss@fairphone.com> # sdm632-fairphone-fp3
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20240130-pmi632-typec-v3-4-b05fe44f0a51@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>

arm64: dts: qcom: qcs6490-rb3gen2: Correct the voltage setting for vph_pwr

Min and max voltages for vph_pwr should be same, otherwise rpmh
will not probe, so correcting the min and max voltages for vph_pwr.

Fixes: 04cf333afc75 ("arm64: dts: qcom: Add base qcs6490-rb3gen2 board dts")
Signed-off-by: Komal Bajaj <quic_kbajaj@quicinc.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20231220110015.25378-3-quic_kbajaj@quicinc.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>

arm64: dts: qcom: qcm6490-idp: Correct the voltage setting for vph_pwr

Min and max voltages for vph_pwr should be same, otherwise rpmh
will not probe, so correcting the min and max voltages for vph_pwr.

Fixes: 9af6a9f32ad0 ("arm64: dts: qcom: Add base qcm6490 idp board dts")
Signed-off-by: Komal Bajaj <quic_kbajaj@quicinc.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20231220110015.25378-2-quic_kbajaj@quicinc.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>

arm64: dts: qcom: sc8280xp: Introduce additional tsens instances

The SC8280XP contains two additional tsens instances, providing among
other things thermal measurements for the GPU.

Add these and a GPU thermal-zone.

Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Reviewed-by: Johan Hovold <johan+linaro@kernel.org>
Signed-off-by: Bjorn Andersson <quic_bjorande@quicinc.com>
Link: https://lore.kernel.org/r/20240206-sc8280xp-tsens2_3-v3-1-4577b3b38ea8@quicinc.com
[bjorn: s/cpu-crit/gpu-crit/]
Signed-off-by: Bjorn Andersson <andersson@kernel.org>

arm64: dts: qcom: sm8550-hdk: correct WCD9385 route and port mapping

Starting from SM8550, the TX ADC input soundwire port is offset by 1,
and uses the new SWR_INPUTx input ports, so replace the legacy
SWR_ADCx routes for SWR_INPUT0 & SWR_INPUT1 following the correct
TX Soundwire port mapping.

Add some comments on the routing for clarity.

Fixes: b5e25ded2721 ("arm64: dts: qcom: sm8550: add support for the SM8550-HDK board")
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20240201-topic-sm8550-hdk8550-audio-fix-v1-1-aa526c9c91d5@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>

arm64: dts: qcom: sm8650: Fix UFS PHY clocks

QMP PHY used in SM8650 requires 3 clocks:

* ref - 19.2MHz reference clock from RPMh
* ref_aux - Auxiliary reference clock from GCC
* qref - QREF clock from TCSR

Fixes: 10e024671295 ("arm64: dts: qcom: sm8650: add interconnect dependent device nodes")
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20240131-ufs-phy-clock-v3-17-58a49d2f4605@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>

arm64: dts: qcom: sm8550: Fix UFS PHY clocks

QMP PHY used in SM8550 requires 3 clocks:

* ref - 19.2MHz reference clock from RPMh
* ref_aux - Auxiliary reference clock from GCC
* qref - QREF clock from TCSR

Fixes: 35cf1aaab169 ("arm64: dts: qcom: sm8550: Add UFS host controller and phy nodes")
Reviewed-by: Can Guo <quic_cang@quicinc.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20240131-ufs-phy-clock-v3-16-58a49d2f4605@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>

arm64: dts: qcom: sm8350: Fix UFS PHY clocks

QMP PHY used in SM8350 requires 3 clocks:

* ref - 19.2MHz reference clock from RPMh
* ref_aux - Auxiliary reference clock from GCC
* qref - QREF clock from GCC

While at it, let's move 'clocks' property before 'clock-names' to match
the style used commonly.

Fixes: 59c7cf814783 ("arm64: dts: qcom: sm8350: Add UFS nodes")
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20240131-ufs-phy-clock-v3-15-58a49d2f4605@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>

arm64: dts: qcom: sc8280xp: Fix UFS PHY clocks

QMP PHY used in SC8280XP requires 3 clocks:

* ref - 19.2MHz reference clock from RPMh
* ref_aux - Auxiliary reference clock from GCC
* qref - QREF clock from GCC

Fixes: 152d1faf1e2f ("arm64: dts: qcom: add SC8280XP platform")
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20240131-ufs-phy-clock-v3-14-58a49d2f4605@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>

arm64: dts: qcom: sc8180x: Fix UFS PHY clocks

QMP PHY used in SC8180X requires 3 clocks:

* ref - 19.2MHz reference clock from RPMh
* ref_aux - Auxiliary reference clock from GCC
* qref - QREF clock from GCC

Fixes: 8575f197b077 ("arm64: dts: qcom: Introduce the SC8180x platform")
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20240131-ufs-phy-clock-v3-13-58a49d2f4605@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>

Merge branch '20240131-ufs-phy-clock-v3-3-58a49d2f4605@linaro.org' into HEAD

Merge clock topic branch that introduces the SC8180X CLK_REF enable
clocks.

arm64: dts: qcom: sm8250: Fix UFS PHY clocks

QMP PHY used in SM8250 requires 3 clocks:

* ref - 19.2MHz reference clock from RPMh
* ref_aux - Auxiliary reference clock from GCC
* qref - QREF clock from GCC

While at it, let's move 'clocks' property before 'clock-names' to match
the style used commonly.

Fixes: b7e2fba06622 ("arm64: dts: qcom: sm8250: Add UFS controller and PHY")
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20240131-ufs-phy-clock-v3-12-58a49d2f4605@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>

arm64: dts: qcom: sm8150: Fix UFS PHY clocks

QMP PHY used in SM8150 requires 3 clocks:

* ref - 19.2MHz reference clock from RPMh
* ref_aux - Auxiliary reference clock from GCC
* qref - QREF clock from GCC

While at it, let's move 'clocks' property before 'clock-names' to match
the style used commonly.

Fixes: 3834a2e92229 ("arm64: dts: qcom: sm8150: Add ufs nodes")
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20240131-ufs-phy-clock-v3-11-58a49d2f4605@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>

arm64: dts: qcom: sm6350: Fix UFS PHY clocks

QMP PHY used in SM6350 requires 3 clocks:

* ref - 19.2MHz reference clock from RPMh
* ref_aux - Auxiliary reference clock from GCC
* qref - QREF clock from GCC

While at it, let's move 'clocks' property before 'clock-names' to match
the style used commonly.

Fixes: 5a814af5fc22 ("arm64: dts: qcom: sm6350: Add UFS nodes")
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20240131-ufs-phy-clock-v3-10-58a49d2f4605@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>

arm64: dts: qcom: sm6125: Fix UFS PHY clocks

QMP PHY used in SM6125 requires 3 clocks:

* ref - 19.2MHz reference clock from RPM
* ref_aux - Auxiliary reference clock from GCC
* qref - QREF clock from GCC

Fixes: f8399e8a2f80 ("arm64: dts: qcom: sm6125: Add UFS nodes")
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20240131-ufs-phy-clock-v3-9-58a49d2f4605@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>

arm64: dts: qcom: sm6115: Fix UFS PHY clocks

QMP PHY used in SM6115 requires 3 clocks:

* ref - 19.2MHz reference clock from RPM
* ref_aux - Auxiliary reference clock from GCC
* qref - QREF clock from GCC

Fixes: 97e563bf5ba1 ("arm64: dts: qcom: sm6115: Add basic soc dtsi")
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20240131-ufs-phy-clock-v3-8-58a49d2f4605@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>

arm64: dts: qcom: sdm845: Fix UFS PHY clocks

QMP PHY used in SDM845 requires 3 clocks:

* ref - 19.2MHz reference clock from RPMh
* ref_aux - Auxiliary reference clock from GCC
* qref - QREF clock from GCC

While at it, let's move 'clocks' property before 'clock-names' to match
the style used commonly.

Fixes: cc16687fbd74 ("arm64: dts: qcom: sdm845: add UFS controller")
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20240131-ufs-phy-clock-v3-7-58a49d2f4605@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>

arm64: dts: qcom: msm8998: Fix UFS PHY clocks

QMP PHY used in MSM8998 requires 3 clocks:

* ref - 19.2MHz reference clock from RPM
* ref_aux - Auxiliary reference clock from GCC
* qref - QREF clock from GCC

Fixes: cd3dbe2a4e6c ("arm64: dts: qcom: msm8998: Add UFS nodes")
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20240131-ufs-phy-clock-v3-6-58a49d2f4605@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>

arm64: dts: qcom: msm8996: Fix UFS PHY clocks

QMP PHY used in MSM8996 requires 2 clocks:

* ref - 19.2MHz reference clock from RPM
* qref - QREF clock from GCC

Fixes: 27520210e881 ("arm64: dts: qcom: msm8996: Use generic QMP driver for UFS")
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20240131-ufs-phy-clock-v3-5-58a49d2f4605@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>

dt-bindings: clock: qcom: Add missing UFS QREF clocks

Add missing QREF clocks for UFS MEM and UFS CARD controllers.

Fixes: 0fadcdfdcf57 ("dt-bindings: clock: Add SC8180x GCC binding")
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20240131-ufs-phy-clock-v3-3-58a49d2f4605@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>

arm64: dts: qcom: ipq8074: add clock-frequency to MDIO node

Add clock-frequency to MDIO node to set the MDC rate to 6.25Mhz instead
of using the default value of 390KHz from MDIO default divider.

Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20240131022731.2118-1-ansuelsmth@gmail.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>

arm64: dts: qcom: qrb2210-rb1: disable cluster power domains

If cluster domain idle state is enabled on the RB1, the board becomes
significantly less responsive. Under certain circumstances (if some of
the devices are disabled in kernel config) the board can even lock up.

It seems this is caused by the MPM not updating wakeup timer during CPU
idle (in the same way the RPMh updates it when cluster idle state is
entered).

Disable cluster domain idle for the RB1 board until MPM driver is fixed
to cooperate with the CPU idle states.

Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20240130-rb1-suspend-cluster-v2-1-5bc1109b0869@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>

arm64: dts: qcom: msm8953: Add GPU

Add the GPU node for the Adreno 506 found on this family of SoCs. The
clock speeds are a bit different per SoC variant, SDM450 maxes out at
600MHz while MSM8953 (= SDM625) goes up to 650MHz and SDM632 goes up to
725MHz.

To achieve this, create a new sdm450.dtsi to hold the 600MHz OPP and
use the new dtsi for sdm450-motorola-ali.

Signed-off-by: Vladimir Lypak <vladimir.lypak@gmail.com>
Co-developed-by: Luca Weiss <luca@z3ntu.xyz>
Signed-off-by: Luca Weiss <luca@z3ntu.xyz>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20240125-msm8953-gpu-v1-2-f6493a5951f3@z3ntu.xyz
Signed-off-by: Bjorn Andersson <andersson@kernel.org>

arm64: dts: qcom: msm8953: Add GPU IOMMU

Add the IOMMU used for the GPU on MSM8953.

Signed-off-by: Vladimir Lypak <vladimir.lypak@gmail.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20240125-msm8953-gpu-v1-1-f6493a5951f3@z3ntu.xyz
Signed-off-by: Bjorn Andersson <andersson@kernel.org>

arm64: dts: qcom: msm8953: add reset for display subsystem

With this reset we can avoid situations like IRQ storms from DSI host
before it even started probing (because boot-loader left DSI IRQs on).

Signed-off-by: Vladimir Lypak <vladimir.lypak@gmail.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Luca Weiss <luca@z3ntu.xyz>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20240125-msm8953-mdss-reset-v2-3-fd7824559426@z3ntu.xyz
Signed-off-by: Bjorn Andersson <andersson@kernel.org>

Merge branch '20240125-msm8953-mdss-reset-v2-1-fd7824559426@z3ntu.xyz' into arm64-for-6.9

Merge MSM8953 GCC DeviceTree binding update from topic branch, to get
access to newly introduced MDSS reset constants.

dt-bindings: clock: gcc-msm8953: add more resets

Add new defines for some more BCRs found on MSM8953.

Signed-off-by: Vladimir Lypak <vladimir.lypak@gmail.com>
[luca: expand commit message, add more resets]
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Luca Weiss <luca@z3ntu.xyz>
Link: https://lore.kernel.org/r/20240125-msm8953-mdss-reset-v2-1-fd7824559426@z3ntu.xyz
Signed-off-by: Bjorn Andersson <andersson@kernel.org>

arm64: dts: qcom: sm8650-mtp: add Audio sound card node

Add the sound card of SM8650-MTP board with the routing for Speakers.

Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20240125-topic-sm8650-upstream-audio-dt-v1-2-c24d23ae5763@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>

arm64: dts: qcom: sm8650-qrd: add Audio nodes

Add the remaining Audio nodes on the SM8650-QRD board including:
- Qualcomm Aqstic WCD9395 audio codec on the RX & TX Soundwire interfaces
- WSA8845 Left & Right Speakers
- Link the WCD9395 Codec node to the WCD9395 USB SubSystem node to handle
  the USB-C Audio Accessory Mode events & lane swapping
- Sound card with routing for Speakers and Microphones

Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20240125-topic-sm8650-upstream-audio-dt-v1-1-c24d23ae5763@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>

arm64: dts: qcom: sm8650: Add dma-coherent property

Add dma-coherent property to fastRPC context bank nodes to pass dma
sequence test in fastrpc sanity test, ensure that data integrity is
maintained during DMA operations.

Signed-off-by: Ling Xu <quic_lxu5@quicinc.com>
Link: https://lore.kernel.org/r/20240125102413.3016-3-quic_lxu5@quicinc.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>

arm64: dts: qcom: sm8550: Add dma-coherent property

Add dma-coherent property to fastRPC context bank nodes to pass dma
sequence test in fastrpc sanity test, ensure that data integrity is
maintained during DMA operations.

Signed-off-by: Ling Xu <quic_lxu5@quicinc.com>
Link: https://lore.kernel.org/r/20240125102413.3016-2-quic_lxu5@quicinc.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>

arm64: dts: qcom: sm8650-qrd: add PM8010 regulators

Add PM8010 regulator device nodes for sm8650-qrd board.

Signed-off-by: Fenglin Wu <quic_fenglinw@quicinc.com>
Reviewed-by: David Collins <quic_collinsd@quicinc.com>
Link: https://lore.kernel.org/r/20240125-sm8650_pm8010_support-v3-2-2f291242a7c4@quicinc.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>

arm64: dts: qcom: sm8650-mtp: add PM8010 regulators

Add PM8010 regulator device nodes for sm8650-mtp board.

Signed-off-by: Fenglin Wu <quic_fenglinw@quicinc.com>
Reviewed-by: David Collins <quic_collinsd@quicinc.com>
Link: https://lore.kernel.org/r/20240125-sm8650_pm8010_support-v3-1-2f291242a7c4@quicinc.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>

arm64: dts: qcom: ipq6018: add thermal zones

Add thermal zones to make use of thermal sensors data. For CPU zone,
add cooling device that uses CPU frequency scaling.

Signed-off-by: Mantas Pucka <mantas@8devices.com>
Link: https://lore.kernel.org/r/1706173452-1017-4-git-send-email-mantas@8devices.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>

arm64: dts: qcom: ipq6018: add tsens node

IPQ6018 has temperature sensing HW block compatible with IPQ8074. Add
node for it.

Signed-off-by: Mantas Pucka <mantas@8devices.com>
Link: https://lore.kernel.org/r/1706173452-1017-3-git-send-email-mantas@8devices.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>

arm64: dts: qcom: sm8550-mtp: add correct analogue microphones

Add proper audio routes for onboard analogue microphones AMIC[1345] -
MIC biases and route from TX macro codec to WCD9385 audio codec.

This should bring AMIC1, AMIC2 (headphones), AMIC3, AMIC4 and AMIC5
onboard microphones to work, although was not tested on the hardware.

Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20240124164505.293202-4-krzysztof.kozlowski@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>

arm64: dts: qcom: sm8550-qrd: add correct analogue microphones

Add proper audio routes for onboard analogue microphones AMIC[1345] -
MIC biases and route from TX macro codec to WCD9385 audio codec.

This finally brings AMIC1, AMIC3, AMIC4 and AMIC5 onboard microphones to
work.  AMIC2 (headphones) should be fine well, however it didn't work
during tests, probably because of incomplete USB switch.

Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20240124164505.293202-3-krzysztof.kozlowski@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>

arm64: dts: qcom: sm8550-mtp: correct WCD9385 TX port mapping

WCD9385 audio codec TX port mapping was copied form HDK8450, but in fact
it is offset by one.  Correct it to fix recording via analogue
microphones.

The change is based on QRD8550 and should be correct here as well, but
was not tested on MTP8550.

Cc: stable@vger.kernel.org
Fixes: a541667c86a9 ("arm64: dts: qcom: sm8550-mtp: add WCD9385 audio-codec")
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20240124164505.293202-2-krzysztof.kozlowski@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>

arm64: dts: qcom: sm8550-qrd: correct WCD9385 TX port mapping

WCD9385 audio codec TX port mapping was copied form HDK8450, but in fact
it is offset by one.  Correct it to fix recording via analogue
microphones.

Cc: stable@vger.kernel.org
Fixes: 83fae950c992 ("arm64: dts: qcom: sm8550-qrd: add WCD9385 audio-codec")
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20240124164505.293202-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>

arm64: dts: qcom: sm6350: Add tsens thermal zones

Add the definitions for the various thermal zones found on the SM6350
SoC. Hooking up GPU and CPU cooling can limit the clock speeds there to
reduce the temperature again to good levels.

Most thermal zones only have one critical temperature configured at
125°C which can be mostly considered a placeholder until those zones can
be hooked up to cooling.

Signed-off-by: Luca Weiss <luca.weiss@fairphone.com>
Link: https://lore.kernel.org/r/20240124-sm6350-tsens-v1-1-d37ec82140af@fairphone.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>

arm64: dts: qcom: sm6115: declare VLS CLAMP register for USB3 PHY

The USB3 PHY on the SM6115 platform doesn't have built-in
PCS_MISC_CLAMP_ENABLE register. Instead clamping is handled separately
via the register in the TCSR space. Declare corresponding register.

Fixes: 9dd5f6dba729 ("arm64: dts: qcom: sm6115: Add USB SS qmp phy node")
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20240117-usbc-phy-vls-clamp-v2-6-a950c223f10f@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>

arm64: dts: qcom: qcm2290: declare VLS CLAMP register for USB3 PHY

The USB3 PHY on the QCM2290 platform doesn't have built-in
PCS_MISC_CLAMP_ENABLE register. Instead clamping is handled separately
via the register in the TCSR space. Declare corresponding register.

Fixes: 0c55f6229bc3 ("arm64: dts: qcom: qcm2290: Add USB3 PHY")
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20240117-usbc-phy-vls-clamp-v2-5-a950c223f10f@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>

arm64: dts: qcom: msm8998: declare VLS CLAMP register for USB3 PHY

The USB3 PHY on the MSM8998 platform doesn't have built-in
PCS_MISC_CLAMP_ENABLE register. Instead clamping is handled separately
via the register in the TCSR space. Declare corresponding register.

Fixes: 026dad8f5873 ("arm64: dts: qcom: msm8998: Add USB-related nodes")
Cc: Jeffrey Hugo <quic_jhugo@quicinc.com>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Reviewed-by: Jeffrey Hugo <quic_jhugo@quicinc.com>
Link: https://lore.kernel.org/r/20240117-usbc-phy-vls-clamp-v2-4-a950c223f10f@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>

arm64: dts: qcom: sc7280: Update domain-idle-states for cluster sleep

QCM6490 uses Trustzone as firmware whereas SC7280 uses arm trusted firmware.
The PSCI suspend param and the number of domain-idle-states supported is
different in Trustzone for cluster sleep.

Move the arm trusted firmware supported domain-idle-states in chrome specific
sc7280-chrome-common.dtsi and add the Trustzone supported sleep states as default
domain-idle-states in sc7280.dtsi

Signed-off-by: Maulik Shah <quic_mkshah@quicinc.com>
Link: https://lore.kernel.org/r/20240109-qcm6490_cluster_sleep-v2-1-8f94f1ad188d@quicinc.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>

arm64: dts: qcom: sdm630-nile: Enable and configure PM660L WLED

The board-specific (electrical) configuration was removed from PM660L in
90ba636e40cb ("arm64: dts: qcom: pm660l: Remove board-specific WLED
configuration") as it is platform-dependent.  We reintroduce it here in
the Nile board configuration (with a slightly lower current limit, as
per downstream DT sources) and enable it for use in the dsi0 node.

Signed-off-by: Marijn Suijten <marijn.suijten@somainline.org>
Link: https://lore.kernel.org/r/20240204-sdm630-nile-wled-v1-1-9f5c4f8147f2@somainline.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>

dt-bindings: arm: qcom: drop the superfluous device compatibility schema

The idea impressed in the commit b32e592d3c28 ("devicetree: bindings:
Document qcom board compatible format") never got actually adopted. As
can be seen from the existing board DT files, no device actually used
the PMIC / foundry / version parts of the compatible string. Drop this
compatibility string description to avoid possible confusion and keep
just the generic terms and the SoC list.

Fixes: b32e592d3c28 ("devicetree: bindings: Document qcom board compatible format")
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20240204-qcom-drop-compat-v1-1-69d6cd92aa0e@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>

arm64: dts: qcom: sm8650: add missing qlink_logging reserved memory for mpss

The qlink_logging memory region is also used by the modem firmware,
add it to the reserved memories and add it to the MPSS memory regions.

Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Mukesh Ojha <quic_mojha@quicinc.com>
Link: https://lore.kernel.org/r/20240123-topic-sm8650-upstream-remoteproc-v7-4-61283f50162f@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>

arm64: dts: qcom: ipq9574: Enable Inline Crypto Engine for MMC

Add Inline Crypto Engine reg and clocks in MMC node and enable CQE
support as Inline Crypto Engine requires CQE to be enabled.

Signed-off-by: Vignesh Viswanathan <quic_viswanat@quicinc.com>
Link: https://lore.kernel.org/r/20231215095339.3055554-1-quic_viswanat@quicinc.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>

arm64: dts: qcom: x1e80100-crd: add WSA8845 speakers

Add nodes for four WSA8845 speakers.  Unlike previous boards like
SM8550-QRD, this board has four speakers spread over two Soundwire buses
instead of two speakers on one bus.  Each pair of speakers shares the
reset GPIO thus pinctrl property is only in one of them.

Cc: Abel Vesa <abel.vesa@linaro.org>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20231214131016.30502-5-krzysztof.kozlowski@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>

arm64: dts: qcom: x1e80100-crd: add WCD9385 Audio Codec

Add Qualcomm Aqstic WCD9385 audio codec on two Soundwire interfaces: RX
and TX.

Cc: Abel Vesa <abel.vesa@linaro.org>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20231214131016.30502-4-krzysztof.kozlowski@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>

arm64: dts: qcom: x1e80100: add Soundwire controllers

Add nodes for LPASS Soundwire v2.0.0 controllers.  Difference against
SM8550:
1. Update port configs to match reference implementation,
2. LPASS TLMM GPIO14 is not used as WCD_SR_TX_DATA2 pin but as GPIO
   (camera).

Cc: Abel Vesa <abel.vesa@linaro.org>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20231214131016.30502-3-krzysztof.kozlowski@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>

arm64: dts: qcom: x1e80100: add ADSP audio codec macros

Add the Low Power Audio SubSystem (LPASS) / ADSP audio codec macros on
Qualcomm SM8650.  The nodes are exactly the same as on SM8550 and
SM8650.

Cc: Abel Vesa <abel.vesa@linaro.org>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20231214131016.30502-2-krzysztof.kozlowski@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>

arm64: dts: qcom: x1e80100: add LPASS LPI pin controller

Add the Low Power Audio SubSystem Low Power Island (LPASS LPI) pin
controller device node as part of audio subsystem in Qualcomm X1E80100
SoC.

Cc: Abel Vesa <abel.vesa@linaro.org>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20231212125632.54021-3-krzysztof.kozlowski@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>

arm64: dts: qcom: x1e80100: add ADSP GPR

Add the ADSP Generic Packet Router (GPR) device node as part of audio
subsystem in Qualcomm X1E80100 SoC.

Cc: Abel Vesa <abel.vesa@linaro.org>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20231212125632.54021-2-krzysztof.kozlowski@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>

arm64: dts: qcom: ipq6018: add QUP5 I2C node

Add node to support this bus inside of IPQ6018.
For example, this bus is used to work with the
voltage regulator (mp5496) on the Yuncore AX840 wireless AP.

Signed-off-by: Isaev Ruslan <legale.legale@gmail.com>
Link: https://lore.kernel.org/r/CACDmYyfOe-jcgj4BAD8=pr08sHpOF=+FRcwrouuLAVsa4+zwtw@mail.gmail.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>

arm64: dts: qcom: x1e80100-qcp: Fix supplies for LDOs 3E and 2J

The LDOs 3E and 2J are actually supplied by SMPS 5J. Fix accordingly.

Fixes: af16b00578a7 ("arm64: dts: qcom: Add base X1E80100 dtsi and the QCP dts")
Acked-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
Link: https://lore.kernel.org/r/20240129-x1e80100-dts-missing-nodes-v6-11-2c0e691cfa3b@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>

arm64: dts: qcom: x1e80100-qcp: Enable more support

Enable display, pcie and usb support.

Co-developed-by: Sibi Sankar <quic_sibis@quicinc.com>
Signed-off-by: Sibi Sankar <quic_sibis@quicinc.com>
Co-developed-by: Rajendra Nayak <quic_rjendra@quicinc.com>
Signed-off-by: Rajendra Nayak <quic_rjendra@quicinc.com>
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
Link: https://lore.kernel.org/r/20240129-x1e80100-dts-missing-nodes-v6-10-2c0e691cfa3b@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>

arm64: dts: qcom: x1e80100-crd: Enable more support

Enable touchscreen, touchpad, keyboard, display, pcie and usb
support.

Co-developed-by: Sibi Sankar <quic_sibis@quicinc.com>
Signed-off-by: Sibi Sankar <quic_sibis@quicinc.com>
Co-developed-by: Rajendra Nayak <quic_rjendra@quicinc.com>
Signed-off-by: Rajendra Nayak <quic_rjendra@quicinc.com>
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
Link: https://lore.kernel.org/r/20240129-x1e80100-dts-missing-nodes-v6-9-2c0e691cfa3b@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>

arm64: dts: qcom: x1e80100: Add display nodes

Add the required nodes to support display on X1E80100.

Co-developed-by: Sibi Sankar <quic_sibis@quicinc.com>
Signed-off-by: Sibi Sankar <quic_sibis@quicinc.com>
Co-developed-by: Rajendra Nayak <quic_rjendra@quicinc.com>
Signed-off-by: Rajendra Nayak <quic_rjendra@quicinc.com>
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
Link: https://lore.kernel.org/r/20240129-x1e80100-dts-missing-nodes-v6-8-2c0e691cfa3b@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>

arm64: dts: qcom: x1e80100: Add PCIe nodes

Add nodes for PCIe 4 and 6 controllers and their PHYs for X1E80100 platform.

Co-developed-by: Sibi Sankar <quic_sibis@quicinc.com>
Signed-off-by: Sibi Sankar <quic_sibis@quicinc.com>
Co-developed-by: Rajendra Nayak <quic_rjendra@quicinc.com>
Signed-off-by: Rajendra Nayak <quic_rjendra@quicinc.com>
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
Link: https://lore.kernel.org/r/20240129-x1e80100-dts-missing-nodes-v6-7-2c0e691cfa3b@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>

arm64: dts: qcom: x1e80100: Add USB nodes

Add nodes for all USB controllers and their PHYs for X1E80100 platform.

Co-developed-by: Sibi Sankar <quic_sibis@quicinc.com>
Signed-off-by: Sibi Sankar <quic_sibis@quicinc.com>
Co-developed-by: Rajendra Nayak <quic_rjendra@quicinc.com>
Signed-off-by: Rajendra Nayak <quic_rjendra@quicinc.com>
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
Link: https://lore.kernel.org/r/20240129-x1e80100-dts-missing-nodes-v6-6-2c0e691cfa3b@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>

arm64: dts: qcom: x1e80100: Add TCSR node

Add the TCSR clock controller and register space node.

Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20240129-x1e80100-dts-missing-nodes-v6-5-2c0e691cfa3b@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>