There is a small race window at snd_pcm_oss_sync() that is called from
OSS PCM SNDCTL_DSP_SYNC ioctl; namely the function calls
snd_pcm_oss_make_ready() at first, then takes the params_lock mutex
for the rest. When the stream is set up again by another thread
between them, it leads to inconsistency, and may result in unexpected
results such as NULL dereference of OSS buffer as a fuzzer spotted
recently.
The fix is simply to cover snd_pcm_oss_make_ready() call into the same
params_lock mutex with snd_pcm_oss_make_ready_locked() variant.
A race condition still exists when removing and re-creating md devices
in test cases. However, it is only seen on some setups.
The race condition was tracked down to a reference still being held
to the kobject by the rdev in the md_rdev_misc_wq which will be released
in rdev_delayed_delete().
md_alloc() waits for previous deletions by waiting on the md_misc_wq,
but the md_rdev_misc_wq may still be holding a reference to a recently
removed device.
To fix this, also flush the md_rdev_misc_wq in md_alloc().
Signed-off-by: David Sloan <david.sloan@eideticom.com>
[logang@deltatee.com: rewrote commit message] Signed-off-by: Logan Gunthorpe <logang@deltatee.com> Signed-off-by: Song Liu <song@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
There is no need to check if the cpufreq driver implements callback
cpufreq_driver::target_index. The logic in the __resolve_freq uses
the frequency table available in the policy. It doesn't matter if the
driver provides 'target_index' or 'target' callback. It just has to
populate the 'policy->freq_table'.
Thus, check only frequency table during the frequency resolving call.
Acked-by: Viresh Kumar <viresh.kumar@linaro.org> Signed-off-by: Lukasz Luba <lukasz.luba@arm.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
When a TCP sends more bytes than allowed by the receive window, all future
packets can be marked as invalid.
This can clog up the conntrack table because of 5-day default timeout.
... all trigger 'ACK is over bound' test and we end up with
non-early-evictable 5-day default timeout.
NB: This patch triggers a bunch of checkpatch warnings because of silly
indent. I will resend the cleanup series linked below to reduce the
indent level once this change has propagated to net-next.
I could route the cleanup via nf but that causes extra backport work for
stable maintainers.
Though acpi_find_last_cache_level() always returned signed value and the
document states it will return any errors caused by lack of a PPTT table,
it never returned negative values before.
Commit 0c80f9e165f8 ("ACPI: PPTT: Leave the table mapped for the runtime usage")
however changed it by returning -ENOENT if no PPTT was found. The value
returned from acpi_find_last_cache_level() is then assigned to unsigned
fw_level.
It will result in the number of cache leaves calculated incorrectly as
a huge value which will then cause the following warning from __alloc_pages
as the order would be great than MAX_ORDER because of incorrect and huge
cache leaves value.
If a 32-bit kernel was compiled for PA2.0 CPUs, it won't be able to run
on machines with PA1.x CPUs. Add a check and bail out early if a PA1.x
machine is detected.
There is no need any longer to have this sanity check, because the
previous commit ("parisc: Make CONFIG_64BIT available for ARCH=parisc64
only") prevents that CONFIG_64BIT is set if ARCH==parisc.
The current power mode change timeout (180 s) is so large that it can cause
a watchdog timer to fire. Reduce the power mode change timeout to 10
seconds.
Link: https://lore.kernel.org/r/20220811234401.1957911-1-bvanassche@acm.org Reviewed-by: Stanley Chu <stanley.chu@mediatek.com> Signed-off-by: Bart Van Assche <bvanassche@acm.org> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Acked-by: Christian König <christian.koenig@amd.com> Signed-off-by: Zhenneng Li <lizhenneng@kylinos.cn> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
V1:
The amdgpu_xgmi_remove_device function will send unload command
to psp through psp ring to terminate xgmi, but psp ring has been
destroyed in psp_hw_fini.
V2:
1. Change the commit title.
2. Restore amdgpu_xgmi_remove_device to its original calling location.
Move psp_xgmi_terminate call from amdgpu_xgmi_remove_device to
psp_hw_fini.
This partially reverts commit d2b292c3f6fd ("scsi: qla2xxx: Enable ATIO
interrupt handshake for ISP27XX")
For some workloads where the host sends a batch of commands and then
pauses, ATIO interrupt coalesce can cause some incoming ATIO entries to be
ignored for extended periods of time, resulting in slow performance,
timeouts, and aborted commands.
Disable interrupt coalesce and re-enable the dedicated ATIO MSI-X
interrupt.
Link: https://lore.kernel.org/r/97dcf365-89ff-014d-a3e5-1404c6af511c@cybernetics.com Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com> Reviewed-by: Nilesh Javali <njavali@marvell.com> Signed-off-by: Tony Battersby <tonyb@cybernetics.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Commit 23c2d497de21 ("mm: kmemleak: take a full lowmem check in
kmemleak_*_phys()") brought false leak alarms on some archs like arm64
that does not init pfn boundary in early booting. The final solution
lands on linux-6.0: commit 0c24e061196c ("mm: kmemleak: add rbtree and
store physical address for objects allocated with PA").
Revert this commit before linux-6.0. The original issue of invalid PA
can be mitigated by additional check in devicetree.
Commit d4252071b97d ("add barriers to buffer_uptodate and
set_buffer_uptodate") added proper memory barriers to the buffer head
BH_Uptodate bit, so that anybody who tests a buffer for being up-to-date
will be guaranteed to actually see initialized state.
However, that commit didn't _just_ add the memory barrier, it also ended
up dropping the "was it already set" logic that the BUFFER_FNS() macro
had.
That's conceptually the right thing for a generic "this is a memory
barrier" operation, but in the case of the buffer contents, we really
only care about the memory barrier for the _first_ time we set the bit,
in that the only memory ordering protection we need is to avoid anybody
seeing uninitialized memory contents.
Any other access ordering wouldn't be about the BH_Uptodate bit anyway,
and would require some other proper lock (typically BH_Lock or the folio
lock). A reader that races with somebody invalidating the buffer head
isn't an issue wrt the memory ordering, it's a serialization issue.
Now, you'd think that the buffer head operations don't matter in this
day and age (and I certainly thought so), but apparently some loads
still end up being heavy users of buffer heads. In particular, the
kernel test robot reported that not having this bit access optimization
in place caused a noticeable direct IO performance regression on ext4:
This reverts commit a8eb8e6f7159c7c20c0ddac428bde3d110890aa7 as
it can cause invalid link quality command sent to the firmware
and address the off-by-one issue by fixing condition of while loop.
Cc: stable@vger.kernel.org Fixes: a8eb8e6f7159 ("wifi: iwlegacy: 4965: fix potential off-by-one overflow in il4965_rs_fill_link_cmd()") Signed-off-by: Stanislaw Gruszka <stf_xl@wp.pl> Signed-off-by: Kalle Valo <kvalo@kernel.org> Link: https://lore.kernel.org/r/20220815073737.GA999388@wp.pl Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A race condition may occur if the user calls close() on another thread
during a write() operation on the device node of the efi capsule.
This is a race condition that occurs between the efi_capsule_write() and
efi_capsule_flush() functions of efi_capsule_fops, which ultimately
results in UAF.
So, the page freeing process is modified to be done in
efi_capsule_release() instead of efi_capsule_flush().
The EFI stub is a wrapper around the core kernel that makes it look like
a EFI compatible PE/COFF application to the EFI firmware. EFI
applications run on top of the EFI runtime, which is heavily based on
so-called protocols, which are struct types consisting [mostly] of
function pointer members that are instantiated and recorded in a
protocol database.
These structs look like the ideal randomization candidates to the
randstruct plugin (as they only carry function pointers), but of course,
these protocols are contracts between the firmware that exposes them,
and the EFI applications (including our stubbed kernel) that invoke
them. This means that struct randomization for EFI protocols is not a
great idea, and given that the stub shares very little data with the
core kernel that is represented as a randomizable struct, we're better
off just disabling it completely here.
Cc: <stable@vger.kernel.org> # v4.14+ Reported-by: Daniel Marth <daniel.marth@inso.tuwien.ac.at> Tested-by: Daniel Marth <daniel.marth@inso.tuwien.ac.at> Signed-off-by: Ard Biesheuvel <ardb@kernel.org> Acked-by: Kees Cook <keescook@chromium.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
drivers/net/wwan/iosm/iosm_ipc_protocol_ops.c: In function ‘ipc_protocol_dl_td_process’:
drivers/net/wwan/iosm/iosm_ipc_protocol_ops.c:406:13: warning: the comparison will always evaluate as ‘true’ for the address of ‘cb’ will never be NULL [-Waddress]
406 | if (!IPC_CB(skb)) {
| ^
Indeed the check seems entirely pointless. Hopefully the other
validation checks will catch if the cb is bad, but it can't be
NULL.
Reviewed-by: M Chetan Kumar <m.chetan.kumar@intel.com> Link: https://lore.kernel.org/r/20220519004342.2109832-1-kuba@kernel.org Signed-off-by: Jakub Kicinski <kuba@kernel.org> Cc: Sudip Mukherjee <sudipm.mukherjee@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
kbuild: fix up permissions on scripts/pahole-flags.sh
Commit b775fbf532dc ("kbuild: Add skip_encoding_btf_enum64 option to
pahole") created the file scripts/pahole-flags.sh, but due to a mismatch
between patch and quilt and git, the execute permissions did not get set
properly. Fix that up.
At least one older CH341 appears to have the RX timer enable bit
inverted so that setting it disables the RX timer and prevents the FIFO
from emptying until it is full.
Only set the RX timer enable bit for devices with version newer than
0x27 (even though this probably affects all pre-0x30 devices).
Reported-by: Jonathan Woithe <jwoithe@just42.net> Tested-by: Jonathan Woithe <jwoithe@just42.net> Link: https://lore.kernel.org/r/Ys1iPTfiZRWj2gXs@marvin.atrad.com.au Fixes: 4e46c410e050 ("USB: serial: ch341: reinitialize chip on reconfiguration") Cc: stable@vger.kernel.org # 4.10 Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Disable LCR updates for pre-0x30 devices which use a different (unknown)
protocol for line control and where the current register write causes
the next received character to be lost.
Note that updating LCR using the INIT command has no effect on these
devices either.
Reported-by: Jonathan Woithe <jwoithe@just42.net> Tested-by: Jonathan Woithe <jwoithe@just42.net> Link: https://lore.kernel.org/r/Ys1iPTfiZRWj2gXs@marvin.atrad.com.au Fixes: 4e46c410e050 ("USB: serial: ch341: reinitialize chip on reconfiguration") Fixes: 55fa15b5987d ("USB: serial: ch341: fix baud rate and line-control handling") Cc: stable@vger.kernel.org # 4.10 Signed-off-by: Johan Hovold <johan@kernel.org>
[ johan: adjust context to 5.15 ] Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The dwc3 driver manages its PHYs itself so the USB core PHY management
needs to be disabled.
Use the struct xhci_plat_priv hack added by commits 46034a999c07 ("usb:
host: xhci-plat: add platform data support") and f768e718911e ("usb:
host: xhci-plat: add priv quirk for skip PHY initialization") to
propagate the setting for now.
Fixes: 4e88d4c08301 ("usb: add a flag to skip PHY initialization to struct usb_hcd") Fixes: 178a0bce05cb ("usb: core: hcd: integrate the PHY wrapper into the HCD core") Tested-by: Matthias Kaehlcke <mka@chromium.org> Cc: stable <stable@kernel.org> Reviewed-by: Matthias Kaehlcke <mka@chromium.org> Signed-off-by: Johan Hovold <johan+linaro@kernel.org> Link: https://lore.kernel.org/r/20220825131836.19769-1-johan+linaro@kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ johan: adjust context to 5.15 ] Signed-off-by: Johan Hovold <johan+linaro@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Qualcomm dwc3 runtime-PM implementation checks the xhci
platform-device pointer in the wakeup-interrupt handler to determine
whether the controller is in host mode and if so triggers a resume.
After a role switch in OTG mode the xhci platform-device would have been
freed and the next wakeup from runtime suspend would access the freed
memory.
Note that role switching is executed from a freezable workqueue, which
guarantees that the pointer is stable during suspend.
Also note that runtime PM has been broken since commit 2664deb09306
("usb: dwc3: qcom: Honor wakeup enabled/disabled state"), which
incidentally also prevents this issue from being triggered.
A null pointer dereference can happen when attempting to access the
"gsm->receive()" function in gsmld_receive_buf(). Currently, the code
assumes that gsm->recieve is only called after MUX activation.
Since the gsmld_receive_buf() function can be accessed without the need to
initialize the MUX, the gsm->receive() function will not be set and a
NULL pointer dereference will occur.
Fix this by avoiding the call to "gsm->receive()" in case the function is
not initialized by adding a sanity check.
The stuff programmed into the wm/ddb registers of planes
on disabled pipes doesn't matter. So during readout just
leave our software state tracking for those zeroed.
This should avoid us trying too hard to clean up after
whatever mess the VBIOS/GOP left in there. The actual
hardware state will get cleaned up if/when we enable
the pipe anyway.
It's been reported that there is a possible data-race accessing to the
global card_requested[] array at ALSA sequencer core, which is used
for determining whether to call request_module() for the card or not.
This data race itself is almost harmless, as it might end up with one
extra request_module() call for the already loaded module at most.
But it's still better to fix.
This patch addresses the possible data race of card_requested[] and
client_requested[] arrays by replacing them with bitmask.
It's an atomic operation and can work without locks.
ALSA OSS sequencer refers to a global variable max_midi_devs at
creating a new port, storing it to its own field. Meanwhile this
variable may be changed by other sequencer events at
snd_seq_oss_midi_check_exit_port() in parallel, which may cause a data
race.
OTOH, this data race itself is almost harmless, as the access to the
MIDI device is done via get_mdev() and it's protected with a refcount,
hence its presence is guaranteed.
Though, it's sill better to address the data-race from the code sanity
POV, and this patch adds the proper spinlock for the protection.
Upon reception, a packet must be categorized, either it's destination is
the host, or it is another host. A packet with no destination addressing
fields may be valid in two situations:
- the packet has no source field: only ACKs are built like that, we
consider the host as the destination.
- the packet has a valid source field: it is directed to the PAN
coordinator, as for know we don't have this information we consider we
are not the PAN coordinator.
There was likely a copy/paste error made during a previous cleanup
because the if clause is now containing exactly the same condition as in
the switch case, which can never be true. In the past the destination
address was used in the switch and the source address was used in the
if, which matches what the spec says.
Cc: stable@vger.kernel.org Fixes: ae531b9475f6 ("ieee802154: use ieee802154_addr instead of *_sa variants") Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com> Link: https://lore.kernel.org/r/20220826142954.254853-1-miquel.raynal@bootlin.com Signed-off-by: Stefan Schmidt <stefan@datenfreihafen.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On 32bit-UP u64_stats_fetch_begin() disables only preemption. If the
reader is in preemptible context and the writer side
(u64_stats_update_begin*()) runs in an interrupt context (IRQ or
softirq) then the writer can update the stats during the read operation.
This update remains undetected.
Use u64_stats_fetch_begin_irq() to ensure the stats fetch on 32bit-UP
are not interrupted by a writer. 32bit-SMP remains unaffected by this
change.
Cc: "David S. Miller" <davem@davemloft.net> Cc: Catherine Sullivan <csully@google.com> Cc: David Awogbemila <awogbemila@google.com> Cc: Dimitris Michailidis <dmichail@fungible.com> Cc: Eric Dumazet <edumazet@google.com> Cc: Hans Ulli Kroll <ulli.kroll@googlemail.com> Cc: Jakub Kicinski <kuba@kernel.org> Cc: Jeroen de Borst <jeroendb@google.com> Cc: Johannes Berg <johannes@sipsolutions.net> Cc: Linus Walleij <linus.walleij@linaro.org> Cc: Paolo Abeni <pabeni@redhat.com> Cc: Simon Horman <simon.horman@corigine.com> Cc: linux-arm-kernel@lists.infradead.org Cc: linux-wireless@vger.kernel.org Cc: netdev@vger.kernel.org Cc: oss-drivers@corigine.com Cc: stable@vger.kernel.org Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Reviewed-by: Simon Horman <simon.horman@corigine.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
__mkroute_input() uses fib_validate_source() to trigger an icmp redirect.
My understanding is that fib_validate_source() is used to know if the src
address and the gateway address are on the same link. For that,
fib_validate_source() returns 1 (same link) or 0 (not the same network).
__mkroute_input() is the only user of these positive values, all other
callers only look if the returned value is negative.
Since the below patch, fib_validate_source() didn't return anymore 1 when
both addresses are on the same network, because the route lookup returns
RT_SCOPE_LINK instead of RT_SCOPE_HOST. But this is, in fact, right.
Let's adapat the test to return 1 again when both addresses are on the same
link.
CC: stable@vger.kernel.org Fixes: 747c14307214 ("ip: fix dflt addr selection for connected nexthop") Reported-by: kernel test robot <yujie.liu@intel.com> Reported-by: Heng Qi <hengqi@linux.alibaba.com> Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com> Reviewed-by: David Ahern <dsahern@kernel.org> Link: https://lore.kernel.org/r/20220829100121.3821-1-nicolas.dichtel@6wind.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
ieee80211_scan_rx() tries to access scan_req->flags after a
null check, but a UAF is observed when the scan is completed
and __ieee80211_scan_completed() executes, which then calls
cfg80211_scan_done() leading to the freeing of scan_req.
Since scan_req is rcu_dereference()'d, prevent the racing in
__ieee80211_scan_completed() by ensuring that from mac80211's
POV it is no longer accessed from an RCU read critical section
before we call cfg80211_scan_done().
When we are not connected to a channel, sending channel "switch"
announcement doesn't make any sense.
The BSS list is empty in that case. This causes the for loop in
cfg80211_get_bss() to be bypassed, so the function returns NULL
(check line 1424 of net/wireless/scan.c), causing the WARN_ON()
in ieee80211_ibss_csa_beacon() to get triggered (check line 500
of net/mac80211/ibss.c), which was consequently reported on the
syzkaller dashboard.
Thus, check if we have an existing connection before generating
the CSA beacon in ieee80211_ibss_finish_csa().
Both __device_attach_driver() and __driver_attach() check the return
code of the bus_type.match() function to see if the device needs to be
added to the deferred probe list. After adding the device to the list,
the logic attempts to bind the device to the driver anyway, as if the
device had matched with the driver, which is not correct.
If __device_attach_driver() detects that the device in question is not
ready to match with a driver on the bus, then it doesn't make sense for
the device to attempt to bind with the current driver or continue
attempting to match with any of the other drivers on the bus. So, update
the logic in __device_attach_driver() to reflect this.
If __driver_attach() detects that a driver tried to match with a device
that is not ready to match yet, then the driver should not attempt to bind
with the device. However, the driver can still attempt to match and bind
with other devices on the bus, as drivers can be bound to multiple
devices. So, update the logic in __driver_attach() to reflect this.
During cdrom emulation, the response to read_toc command must contain
the cdrom address as the number of sectors (2048 byte sized blocks)
represented either as an absolute value (when MSF bit is '0') or in
terms of PMin/PSec/PFrame (when MSF bit is set to '1'). Incase of
cdrom, the fsg_lun_open call sets the sector size to 2048 bytes.
When MAC OS sends a read_toc request with MSF set to '1', the
store_cdrom_address assumes that the address being provided is the
LUN size represented in 512 byte sized blocks instead of 2048. It
tries to modify the address further to convert it to 2048 byte sized
blocks and store it in MSF format. This results in data transfer
failures as the cdrom address being provided in the read_toc response
is incorrect.
This happens when @udev->reset_resume is set to true, when usb resume,
the flow as below:
- hub_resume
- usb_disable_interface
- usb_disable_endpoint
- usb_hcd_disable_endpoint
- xhci_endpoint_disable // it set @ep->hcpriv to NULL
Then when reset usb device, it will drop allocated endpoints,
the flow as below:
- usb_reset_and_verify_device
- usb_hcd_alloc_bandwidth
- xhci_mtk_drop_ep
but @ep->hcpriv is already set to NULL, the bandwidth will be not
released anymore.
Due to the added endponts are stored in hash table, we can drop the check
of @ep->hcpriv.
Fixes: 4ce186665e7c ("usb: xhci-mtk: Do not use xhci's virt_dev in drop_endpoint") Cc: stable <stable@kernel.org> Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com> Link: https://lore.kernel.org/r/20220819080556.32215-2-chunfeng.yun@mediatek.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently uses the worst case byte budgets on FS/LS bus bandwidth,
for example, for an isochronos IN endpoint with 192 bytes budget, it
will consume the whole 5 uframes(188 * 5) while the actual FS bus
budget should be just 192 bytes. It cause that many usb audio headsets
with 3 interfaces (audio input, audio output, and HID) cannot be
configured.
To improve it, changes to use "approximate" best case budget for FS/LS
bandwidth management. For the same endpoint from the above example,
the approximate best case budget is now reduced to (188 * 2) bytes.
This turned out not to be an error in usb-storage but rather a nested
device reset attempt. That is, as the rtl8712 driver was being
unbound from a composite device in preparation for an unrelated USB
reset (that driver does not have pre_reset or post_reset callbacks),
its ->remove routine called usb_reset_device() -- thus nesting one
reset call within another.
Performing a reset as part of disconnect processing is a questionable
practice at best. However, the bug report points out that the USB
core does not have any protection against nested resets. Adding a
reset_in_progress flag and testing it will prevent such errors in the
future.
Add proper alignment for .nospec_call_table and .nospec_return_table in
vmlinux.
[hca@linux.ibm.com]: The problem with the missing alignment of the nospec
tables exist since a long time, however only since commit e6ed91fd0768
("s390/alternatives: remove padding generation code") and with
CONFIG_RELOCATABLE=n the kernel may also crash at boot time.
The above named commit reduced the size of struct alt_instr by one byte,
so its new size is 11 bytes. Therefore depending on the number of cpu
alternatives the size of the __alt_instructions array maybe odd, which
again also causes that the addresses of the nospec tables will be odd.
If the address of __nospec_call_start is odd and the kernel is compiled
With CONFIG_RELOCATABLE=n the compiler may generate code that loads the
address of __nospec_call_start with a 'larl' instruction.
This will generate incorrect code since the 'larl' instruction only works
with even addresses. In result the members of the nospec tables will be
accessed with an off-by-one offset, which subsequently may lead to
addressing exceptions within __nospec_revert().
The alignment check in prepare_hugepage_range() is wrong for 2 GB
hugepages, it only checks for 1 MB hugepage alignment.
This can result in kernel crash in __unmap_hugepage_range() at the
BUG_ON(start & ~huge_page_mask(h)) alignment check, for mappings
created with MAP_FIXED at unaligned address.
Fix this by correctly handling multiple hugepage sizes, similar to the
generic version of prepare_hugepage_range().
Fixes: d08de8e2d867 ("s390/mm: add support for 2GB hugepages") Cc: <stable@vger.kernel.org> # 4.8+ Acked-by: Alexander Gordeev <agordeev@linux.ibm.com> Signed-off-by: Gerald Schaefer <gerald.schaefer@linux.ibm.com> Signed-off-by: Vasily Gorbik <gor@linux.ibm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The TRB_SMM flag indicates that DMA has completed the TD service with
this TRB. Usually it’s a last TRB in TD. In case of ISOC transfer for
bInterval > 1 each ISOC transfer contains more than one TD associated
with usb request (one TD per ITP). In such case the TRB_SMM flag will
be set in every TD and driver will recognize the end of transfer after
processing the first TD with TRB_SMM. In result driver stops updating
request->actual and returns incorrect actual length.
To fix this issue driver additionally must check TRB_CHAIN which is not
used for isochronous transfers.
Fixes: 249f0a25e8be ("usb: cdns3: gadget: handle sg list use case at completion correctly")
cc: <stable@vger.kernel.org> Acked-by: Peter Chen <peter.chen@kernel.org> Signed-off-by: Pawel Laszczak <pawell@cadence.com> Link: https://lore.kernel.org/r/20220825062207.5824-1-pawell@cadence.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
ISO OUT endpoint is enabled during queuing first usb request
in transfer ring and disabled when TRBERR is reported by controller.
After TRBERR and before next transfer added to TR driver must again
reenable endpoint but does not.
To solve this issue during processing TRBERR event driver must
set the flag EP_UPDATE_EP_TRBADDR in priv_ep->flags field.
Since 1599069a62c6 ("phy: core: Warn when phy_power_on is called before
phy_init") the driver complains. In my case (Amlogic SoC) the warning
is: phy phy-fe03e000.phy.2: phy_power_on was called before phy_init
So change the order of the two calls. The same change has to be done
to the order of phy_exit() and phy_power_off().
When the port does not support USB PD, prevent transition to PD
only states when power supply property is written. In this case,
TCPM transitions to SNK_NEGOTIATE_CAPABILITIES
which should not be the case given that the port is not pd_capable.
This adds the necessary ACPI ID for Intel Meteor Lake
IOM devices.
The callback function is_memory() is modified so that it
also checks if the resource descriptor passed to it is a
memory type "Address Space Resource Descriptor".
On Intel Meteor Lake the ACPI memory resource is not
described using the "32-bit Memory Range Descriptor" because
the memory is outside of the 32-bit address space. The
memory resource is described using the "Address Space
Resource Descriptor" instead.
Intel Meteor Lake is the first platform to describe the
memory resource for this device with Address Space Resource
Descriptor, but it most likely will not be the last.
Therefore the change to the is_memory() callback function
is made generic.
Fix incorrect pin assignment values when connecting to a monitor with
Type-C receptacle instead of a plug.
According to specification, an UFP_D receptacle's pin assignment
should came from the UFP_D pin assignments field (bit 23:16), while
an UFP_D plug's assignments are described in the DFP_D pin assignments
(bit 15:8) during Mode Discovery.
For example the LG 27 UL850-W is a monitor with Type-C receptacle.
The monitor responds to MODE DISCOVERY command with following
DisplayPort Capability flag:
dp->alt->vdo=0x140045
The existing logic only take cares of UPF_D plug case,
and would take the bit 15:8 for this 0x140045 case.
This results in an non-existing pin assignment 0x0 in
dp_altmode_configure.
To fix this problem a new set of macros are introduced
to take plug/receptacle differences into consideration.
Fixes: 0e3bb7d6894d ("usb: typec: Add driver for DisplayPort alternate mode") Cc: stable@vger.kernel.org Co-developed-by: Pablo Sun <pablo.sun@mediatek.com> Co-developed-by: Macpaul Lin <macpaul.lin@mediatek.com> Reviewed-by: Guillaume Ranquet <granquet@baylibre.com> Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com> Signed-off-by: Pablo Sun <pablo.sun@mediatek.com> Signed-off-by: Macpaul Lin <macpaul.lin@mediatek.com> Link: https://lore.kernel.org/r/20220804034803.19486-1-macpaul.lin@mediatek.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
After xHC controller is started, either in probe or resume, it can take
a while before any of the connected usb devices are visible to the roothub
due to link training.
It's possible xhci driver loads, sees no acivity and suspends the host
before the USB device is visible.
In one testcase with a hotplugged xHC controller the host finally detected
the connected USB device and generated a wake 500ms after host initial
start.
If hosts didn't suspend the device duringe training it probablty wouldn't
take up to 500ms to detect it, but looking at specs reveal USB3 link
training has a couple long timeout values, such as 120ms
RxDetectQuietTimeout, and 360ms PollingLFPSTimeout.
So Add a 500ms grace period that keeps polling the roothub for 500ms after
start, preventing runtime suspend until USB devices are detected.
The reason for the warning is clear enough; the driver sends an
unusual read request on endpoint 0 but does not set the USB_DIR_IN bit
in the bRequestType field.
More importantly, the whole situation can be avoided and the driver
simplified by converting it over to the relatively new
usb_control_msg_recv() and usb_control_msg_send() routines. That's
what this fix does.
This adds the necessary PCI device ID for the controller
inside the Intel Raptor Lake CPU block. The controllers that
are part of the PCH (chipset) have separate device IDs.
The received notification packet is held in pkg->buffer and not in pkg
itself. Fix this by using the correct buffer.
Fixes: 81a54b5e1986 ("thunderbolt: Let the connection manager handle all notifications") Cc: stable@vger.kernel.org Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Xen blkfront advertises its support of the persistent grants feature
when it first setting up and when resuming in 'talk_to_blkback()'.
Then, blkback reads the advertised value when it connects with blkfront
and decides if it will use the persistent grants feature or not, and
advertises its decision to blkfront. Blkfront reads the blkback's
decision and it also makes the decision for the use of the feature.
Commit 402c43ea6b34 ("xen-blkfront: Apply 'feature_persistent' parameter
when connect"), however, made the blkfront's read of the parameter for
disabling the advertisement, namely 'feature_persistent', to be done
when it negotiate, not when advertise. Therefore blkfront advertises
without reading the parameter. As the field for caching the parameter
value is zero-initialized, it always advertises as the feature is
disabled, so that the persistent grants feature becomes always disabled.
This commit fixes the issue by making the blkfront does parmeter caching
just before the advertisement.
Fixes: 402c43ea6b34 ("xen-blkfront: Apply 'feature_persistent' parameter when connect") Cc: <stable@vger.kernel.org> # 5.10.x Reported-by: Marek Marczykowski-Górecki <marmarek@invisiblethingslab.com> Signed-off-by: SeongJae Park <sj@kernel.org> Tested-by: Marek Marczykowski-Górecki <marmarek@invisiblethingslab.com> Reviewed-by: Juergen Gross <jgross@suse.com> Link: https://lore.kernel.org/r/20220831165824.94815-4-sj@kernel.org Signed-off-by: Juergen Gross <jgross@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The advertisement of the persistent grants feature (writing
'feature-persistent' to xenbus) should mean not the decision for using
the feature but only the availability of the feature. However, commit 74a852479c68 ("xen-blkfront: add a parameter for disabling of persistent
grants") made a field of blkfront, which was a place for saving only the
negotiation result, to be used for yet another purpose: caching of the
'feature_persistent' parameter value. As a result, the advertisement,
which should follow only the parameter value, becomes inconsistent.
This commit fixes the misuse of the semantic by making blkfront saves
the parameter value in a separate place and advertises the support based
on only the saved value.
Fixes: 74a852479c68 ("xen-blkfront: add a parameter for disabling of persistent grants") Cc: <stable@vger.kernel.org> # 5.10.x Suggested-by: Juergen Gross <jgross@suse.com> Signed-off-by: SeongJae Park <sj@kernel.org> Tested-by: Marek Marczykowski-Górecki <marmarek@invisiblethingslab.com> Reviewed-by: Juergen Gross <jgross@suse.com> Link: https://lore.kernel.org/r/20220831165824.94815-3-sj@kernel.org Signed-off-by: Juergen Gross <jgross@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The advertisement of the persistent grants feature (writing
'feature-persistent' to xenbus) should mean not the decision for using
the feature but only the availability of the feature. However, commit aac8a70db24b ("xen-blkback: add a parameter for disabling of persistent
grants") made a field of blkback, which was a place for saving only the
negotiation result, to be used for yet another purpose: caching of the
'feature_persistent' parameter value. As a result, the advertisement,
which should follow only the parameter value, becomes inconsistent.
This commit fixes the misuse of the semantic by making blkback saves the
parameter value in a separate place and advertises the support based on
only the saved value.
Fixes: aac8a70db24b ("xen-blkback: add a parameter for disabling of persistent grants") Cc: <stable@vger.kernel.org> # 5.10.x Suggested-by: Juergen Gross <jgross@suse.com> Signed-off-by: SeongJae Park <sj@kernel.org> Tested-by: Marek Marczykowski-Górecki <marmarek@invisiblethingslab.com> Reviewed-by: Juergen Gross <jgross@suse.com> Link: https://lore.kernel.org/r/20220831165824.94815-2-sj@kernel.org Signed-off-by: Juergen Gross <jgross@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The mmap lock protects the page walker from changes to the page tables
during the walk. However a read lock is insufficient to protect those
areas which don't have a VMA as munmap() detaches the VMAs before
downgrading to a read lock and actually tearing down PTEs/page tables.
For users of walk_page_range() the solution is to simply call pte_hole()
immediately without checking the actual page tables when a VMA is not
present. We now never call __walk_page_range() without a valid vma.
For walk_page_range_novma() the locking requirements are tightened to
require the mmap write lock to be taken, and then walking the pgd
directly with 'no_vma' set.
This in turn means that all page walkers either have a valid vma, or
it's that special 'novma' case for page table debugging. As a result,
all the odd '(!walk->vma && !walk->no_vma)' tests can be removed.
Fixes: dd2283f2605e ("mm: mmap: zap pages with read mmap_sem in munmap") Reported-by: Jann Horn <jannh@google.com> Signed-off-by: Steven Price <steven.price@arm.com> Cc: Vlastimil Babka <vbabka@suse.cz> Cc: Thomas Hellström <thomas.hellstrom@linux.intel.com> Cc: Konstantin Khlebnikov <koct9i@gmail.com> Cc: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The change from kcalloc() to kvmalloc() means that arg->nr_pages
might now be large enough that the "args->nr_pages << PAGE_SHIFT" can
result in an integer overflow.
Fixes: b3f7931f5c61 ("xen/gntdev: switch from kcalloc() to kvcalloc()") Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Reviewed-by: Juergen Gross <jgross@suse.com> Link: https://lore.kernel.org/r/YxDROJqu/RPvR0bi@kili Signed-off-by: Juergen Gross <jgross@suse.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
KVM should not claim to virtualize unknown IA32_ARCH_CAPABILITIES
bits. When kvm_get_arch_capabilities() was originally written, there
were only a few bits defined in this MSR, and KVM could virtualize all
of them. However, over the years, several bits have been defined that
KVM cannot just blindly pass through to the guest without additional
work (such as virtualizing an MSR promised by the
IA32_ARCH_CAPABILITES feature bit).
Define a mask of supported IA32_ARCH_CAPABILITIES bits, and mask off
any other bits that are set in the hardware MSR.
Cc: Paolo Bonzini <pbonzini@redhat.com> Fixes: 5b76a3cff011 ("KVM: VMX: Tell the nested hypervisor to skip L1D flush on vmentry") Signed-off-by: Jim Mattson <jmattson@google.com> Reviewed-by: Vipin Sharma <vipinsh@google.com> Reviewed-by: Xiaoyao Li <xiaoyao.li@intel.com>
Message-Id: <20220830174947.2182144-1-jmattson@google.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The regcache sync will set the cache_bypass = true, at that
time, when there is regmap write operation, it will bypass
the regmap cache, then the regcache sync will write back the
value from cache to register, which is not as our expectation.
Though regmap already use its internal lock to avoid such issue,
but this driver force disable the regmap internal lock in its
regmap config: disable_locking = true
To avoid this issue, use the driver's own lock to do the protect
in system PM.
The driver does not check if the cooling state passed to
gpio_fan_set_cur_state() exceeds the maximum cooling state as
stored in fan_data->num_speeds. Since the cooling state is later
used as an array index in set_fan_speed(), an array out of bounds
access can occur.
This can be exploited by setting the state of the thermal cooling device
to arbitrary values, causing for example a kernel oops when unavailable
memory is accessed this way.
The while loop in raspberrypi_discover_clocks() relies on the assumption
that the id of the last clock element is zero. Because this data comes
from the Videocore firmware and it doesn't guarantuee such a behavior
this could lead to out-of-bounds access. So fix this by providing
a sentinel element.
Fixes: 93d2725affd6 ("clk: bcm: rpi: Discover the firmware clocks") Link: https://github.com/raspberrypi/firmware/issues/1688 Suggested-by: Phil Elwell <phil@raspberrypi.com> Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com> Link: https://lore.kernel.org/r/20220713154953.3336-2-stefan.wahren@i2se.com Acked-by: Florian Fainelli <f.fainelli@gmail.com> Reviewed-by: Ivan T. Ivanov <iivanov@suse.de> Signed-off-by: Stephen Boyd <sboyd@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
We should have 'n', then 'size', not the opposite.
This is harmless because the 2 values are just multiplied, but having
the correct order silence a (unpublished yet) smatch warning.
The function raspberrypi_fw_get_rate (e.g. used for the recalc_rate
hook) can fail to get the clock rate from the firmware. In this case
we cannot return a signed error value, which would be casted to
unsigned long. Fix this by returning 0 instead.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com> Link: https://lore.kernel.org/r/20220625083643.4012-1-stefan.wahren@i2se.com Fixes: 4e85e535e6cc ("clk: bcm283x: add driver interfacing with Raspberry Pi's firmware") Acked-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: Stephen Boyd <sboyd@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
In the original commit 9a34b45397e5 ("clk: Add support for runtime PM"),
the commit message mentioned that pm_runtime_put_sync() would be done
at the end of clk_core_unprepare(). This mirrors the operations in
clk_core_prepare() in the opposite order.
However, the actual code that was added wasn't in the order the commit
message described. Move clk_pm_runtime_put() to the end of
clk_core_unprepare() so that it is in the correct order.
Fixes: 9a34b45397e5 ("clk: Add support for runtime PM") Signed-off-by: Chen-Yu Tsai <wenst@chromium.org> Reviewed-by: Nícolas F. R. A. Prado <nfraprado@collabora.com> Link: https://lore.kernel.org/r/20220822081424.1310926-3-wenst@chromium.org Signed-off-by: Stephen Boyd <sboyd@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
This reverts commit 35b0fac808b95eea1212f8860baf6ad25b88b087. Alexander
reports that it causes boot failures on i.MX8M Plus based boards
(specifically imx8mp-tqma8mpql-mba8mpxl.dts).
In the previous commits that added CLK_OPS_PARENT_ENABLE, support for
this flag was only added to rate change operations (rate setting and
reparent) and disabling unused subtree. It was not added to the
clock gate related operations. Any hardware driver that needs it for
these operations will either see bogus results, or worse, hang.
This has been seen on MT8192 and MT8195, where the imp_ii2_* clk
drivers set this, but dumping debugfs clk_summary would cause it
to hang.
Fixes: fc8726a2c021 ("clk: core: support clocks which requires parents enable (part 2)") Fixes: a4b3518d146f ("clk: core: support clocks which requires parents enable (part 1)") Signed-off-by: Chen-Yu Tsai <wenst@chromium.org> Reviewed-by: Nícolas F. R. A. Prado <nfraprado@collabora.com> Tested-by: Nícolas F. R. A. Prado <nfraprado@collabora.com> Link: https://lore.kernel.org/r/20220822081424.1310926-2-wenst@chromium.org Signed-off-by: Stephen Boyd <sboyd@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
There is a spelling mistake in a gvt_vgpu_err error message. Fix it.
Fixes: 695fbc08d80f ("drm/i915/gvt: replace the gvt_err with gvt_vgpu_err") Signed-off-by: Colin Ian King <colin.i.king@gmail.com> Signed-off-by: Zhi Wang <zhi.a.wang@intel.com> Link: http://patchwork.freedesktop.org/patch/msgid/20220315202449.2952845-1-colin.i.king@gmail.com Reviewed-by: Zhi Wang <zhi.a.wang@intel.com> Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Regardless of the 'msr' argument passed to the VMX version of
msr_write_intercepted(), the function always checks to see if a
specific MSR (IA32_SPEC_CTRL) is intercepted for write. This behavior
seems unintentional and unexpected.
Modify the function so that it checks to see if the provided 'msr'
index is intercepted for write.
Fixes: 67f4b9969c30 ("KVM: nVMX: Handle dynamic MSR intercept toggling") Cc: Sean Christopherson <seanjc@google.com> Signed-off-by: Jim Mattson <jmattson@google.com> Reviewed-by: Sean Christopherson <seanjc@google.com>
Message-Id: <20220810213050.2655000-1-jmattson@google.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
In some cases of failure (dialect mismatches) in SMB2_negotiate(), after
the request is sent, the checks would return -EIO when they should be
rather setting rc = -EIO and jumping to neg_exit to free the response
buffer from mempool.
Signed-off-by: Enzo Matsumiya <ematsumiya@suse.de> Cc: stable@vger.kernel.org Reviewed-by: Ronnie Sahlberg <lsahlber@redhat.com> Signed-off-by: Steve French <stfrench@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Syzbot reported a couple issues introduced by commit 44e602b4e52f
("binder_alloc: add missing mmap_lock calls when using the VMA"), in
which we attempt to acquire the mmap_lock when alloc->vma_vm_mm has not
been initialized yet.
This can happen if a binder_proc receives a transaction without having
previously called mmap() to setup the binder_proc->alloc space in [1].
Also, a similar issue occurs via binder_alloc_print_pages() when we try
to dump the debugfs binder stats file in [2].
Fix these issues by setting up alloc->vma_vm_mm pointer during open()
and caching directly from current->mm. This guarantees we have a valid
reference to take the mmap_lock during scenarios described above.
A transaction of type BINDER_TYPE_WEAK_HANDLE can fail to increment the
reference for a node. In this case, the target proc normally releases
the failed reference upon close as expected. However, if the target is
dying in parallel the call will race with binder_deferred_release(), so
the target could have released all of its references by now leaving the
cleanup of the new failed reference unhandled.
The transaction then ends and the target proc gets released making the
ref->proc now a dangling pointer. Later on, ref->node is closed and we
attempt to take spin_lock(&ref->proc->inner_lock), which leads to the
use-after-free bug reported below. Let's fix this by cleaning up the
failed reference on the spot instead of relying on the target to do so.
==================================================================
BUG: KASAN: use-after-free in _raw_spin_lock+0xa8/0x150
Write of size 4 at addr ffff5ca207094238 by task kworker/1:0/590
If re-initialization results is a different signal voltage, because the
voltage switch failed previously, but not this time (or vice versa), then
sd3_bus_mode will be inconsistent with the card because the SD_SWITCH
command is done only upon first initialization.
Fix by always reading SD_SWITCH information during re-initialization, which
also means it does not need to be re-read later for the 1.8V fixup
workaround.
Note, brief testing showed SD_SWITCH took about 1.8ms to 2ms which added
about 1% to 1.5% to the re-initialization time, so it's not particularly
significant.
Reported-by: Seunghui Lee <sh043.lee@samsung.com> Signed-off-by: Adrian Hunter <adrian.hunter@intel.com> Reviewed-by: Seunghui Lee <sh043.lee@samsung.com> Tested-by: Seunghui Lee <sh043.lee@samsung.com> Cc: stable@vger.kernel.org Link: https://lore.kernel.org/r/20220815073321.63382-3-adrian.hunter@intel.com Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When introduced, upon success, the 1.8V fixup workaround in
mmc_sd_init_card() would branch to practically the end of the function, to
a label named "done". Unfortunately, perhaps due to the label name, over
time new code has been added that really should have come after "done" not
before it. Let's fix the problem by moving the label to the correct place
and rename it "cont".
Fixes: 045d705dc1fb ("mmc: core: Enable the MMC host software queue for the SD card") Signed-off-by: Adrian Hunter <adrian.hunter@intel.com> Reviewed-by: Seunghui Lee <sh043.lee@samsung.com> Cc: stable@vger.kernel.org Link: https://lore.kernel.org/r/20220815073321.63382-2-adrian.hunter@intel.com Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The probe session-duplication overflow check incremented the session
count also when there were no more available sessions so that memory
beyond the fixed-size slab-allocated session array could be corrupted in
fastrpc_session_alloc() on open().
Add the missing sanity check on the probed-session count to avoid
corrupting memory beyond the fixed-size slab-allocated session array
when there are more than FASTRPC_MAX_SESSIONS sessions defined in the
devicetree.
The ad7292 tries to add an devm_action for disabling a regulator at
device detach using devm_add_action_or_reset(). The
devm_add_action_or_reset() does call the release function should adding
action fail. The driver inspects the value returned by
devm_add_action_or_reset() and manually calls regulator_disable() if
adding the action has failed. This leads to double disable and messes
the enable count for regulator.
Do not manually call disable if devm_add_action_or_reset() fails.
Fixes: 506d2e317a0a ("iio: adc: Add driver support for AD7292") Signed-off-by: Matti Vaittinen <mazziesaccount@gmail.com> Tested-by: Marcelo Schmitt <marcelo.schmitt1@gmail.com> Link: https://lore.kernel.org/r/Yv9O+9sxU7gAv3vM@fedora Cc: <Stable@vger.kernel.org> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
syzbot is reporting hung task at __input_unregister_device() [1], for
iforce_close() waiting at wait_event_interruptible() with dev->mutex held
is blocking input_disconnect_device() from __input_unregister_device().
It seems that the cause is simply that commit c2b27ef672992a20 ("Input:
iforce - wait for command completion when closing the device") forgot to
call wake_up() after clear_bit().
Fix this problem by introducing a helper that calls clear_bit() followed
by wake_up_all().
Reported-by: syzbot <syzbot+deb6abc36aad4008f407@syzkaller.appspotmail.com> Fixes: c2b27ef672992a20 ("Input: iforce - wait for command completion when closing the device") Tested-by: syzbot <syzbot+deb6abc36aad4008f407@syzkaller.appspotmail.com> Suggested-by: Fabio M. De Francesco <fmdefrancesco@gmail.com> Co-developed-by: Hillf Danton <hdanton@sina.com> Signed-off-by: Hillf Danton <hdanton@sina.com> Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp> Link: https://lore.kernel.org/r/887021c3-4f13-40ce-c8b9-aa6e09faa3a7@I-love.SAKURA.ne.jp Cc: stable@vger.kernel.org Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When the user initializes the uart port, and waits for the transmit
engine to complete in lpuart32_set_termios(), if the UART TX fifo has
dirty data and the UARTMODIR enable the flow control, the TX fifo may
never be empty. So here we should disable the flow control first to make
sure the transmit engin can complete.
Turning on NOP_USB_XCEIV as builtin broke the TUSB6010 driver because
of an older issue with the depencency.
It is not necessary to forbid NOP_USB_XCEIV=y in combination with
USB_MUSB_HDRC=m, but only the reverse, which causes the link failure
from the original Kconfig change.
Use the correct dependency to still allow NOP_USB_XCEIV=n or
NOP_USB_XCEIV=y but forbid NOP_USB_XCEIV=m when USB_MUSB_HDRC=m
to fix the multi_v7_defconfig for tusb.
projects / linux.git / log