Arnd Bergmann [Fri, 29 Jan 2021 15:29:19 +0000 (16:29 +0100)]
Merge tag 'stm32-dt-for-v5.12-1' of git://git./linux/kernel/git/atorgue/stm32 into arm/dt
STM32 DT updates for v5.12, round 1
Highlights:
----------
MCU part:
-Rename mmc nodes to match with yaml validation.
MPU part:
-Rename mmc nodes to match with yaml validation.
-Move vdda1v1 & vdda1v8 (used by usbphyc) from boards files
to SoC dtsi file.
-LXA:
-Fix leds schema for yaml validation.
-DH:
-Enable SDMMC1 internal pull-ups and disable CKIN feedabck clock
on DHCOM.
-Add SDMMC1 init state inorder to use some gpios during probing phase.
-Disable KS8851 and FMC on PicoITX board.
* tag 'stm32-dt-for-v5.12-1' of git://git.kernel.org/pub/scm/linux/kernel/git/atorgue/stm32:
ARM: dts: stm32: add #clock-cells property to usbphyc node on stm32mp151
ARM: dts: stm32: remove usbphyc ports vdda1v1 & vdda1v8 on stm32mp15 boards
ARM: dts: stm32: add usbphyc vdda1v1 and vdda1v8 supplies on stm32mp151
ARM: dts: stm32: Add STM32MP1 I2C6 SDA/SCL pinmux
ARM: dts: stm32: Rename mmc controller nodes to mmc@
ARM: dts: stm32: Enable voltage translator auto-detection on DHCOM
ARM: dts: stm32: Add additional init state for SDMMC1 pins
ARM: dts: stm32: Disable KS8851 and FMC on PicoITX board
ARM: dts: stm32: Fix schema warnings for pwm-leds on lxa-mc1
ARM: dts: stm32: Disable SDMMC1 CKIN feedback clock on DHCOM
ARM: dts: stm32: Enable internal pull-ups for SDMMC1 on DHCOM SoM
ARM: dts: stm32: Fix GPIO hog flags on DHCOM DRC02
ARM: dts: stm32: Fix GPIO hog flags on DHCOM PicoITX
ARM: dts: stm32: Fix GPIO hog names on DHCOM
ARM: dts: stm32: Disable optional TSC2004 on DRC02 board
ARM: dts: stm32: Disable WP on DHCOM uSD slot
ARM: dts: stm32: Connect card-detect signal on DHCOM
ARM: dts: stm32: Fix polarity of the DH DRC02 uSD card detect
Link: https://lore.kernel.org/r/5e8897a0-8f68-5e41-bfa0-ccdf1e23a3c1@foss.st.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Arnd Bergmann [Fri, 29 Jan 2021 13:02:49 +0000 (14:02 +0100)]
Merge tag 'renesas-arm-dt-for-v5.12-tag2' of git://git./linux/kernel/git/geert/renesas-devel into arm/dt
Renesas ARM DT updates for v5.12 (take two)
- Increase support (SPI, I2C, Ethernet, Serial, MMC) for the R-Car V3U
SoC on the Renesas Falcon board,
- Disable SD functions for plain eMMC,
- A minor fix.
* tag 'renesas-arm-dt-for-v5.12-tag2' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-devel:
arm64: dts: renesas: beacon: Fix EEPROM compatible value
arm64: dts: renesas: falcon: Enable MMC
arm64: dts: renesas: r8a779a0: Add MMC node
arm64: dts: renesas: r8a779a0: Add HSCIF support
arm64: dts: renesas: falcon: Complete SCIF0 nodes
arm64: dts: renesas: r8a779a0: Add & update SCIF nodes
arm64: dts: renesas: falcon: Add Ethernet-AVB0 support
arm64: dts: renesas: r8a779a0: Add Ethernet-AVB support
arm64: dts: renesas: falcon: Add I2C0,1,6 support
arm64: dts: renesas: r8a779a0: Add I2C nodes
arm64: dts: renesas: Disable SD functions for plain eMMC
arm64: dts: renesas: r8a779a0: Add MSIOF device nodes
Link: https://lore.kernel.org/r/20210129090815.2552425-2-geert+renesas@glider.be
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Arnd Bergmann [Fri, 29 Jan 2021 12:57:06 +0000 (13:57 +0100)]
Merge tag 'hisi-arm64-dt-for-5.12v2' of git://github.com/hisilicon/linux-hisi into arm/dt
ARM64: DT: Hisilicon ARM64 DT updates for 5.12
- Further cleanups of the hisilicon DTS to align with the dtschema
- Add or update the I2C, pinctrl and reset nodes for Hikey970
* tag 'hisi-arm64-dt-for-5.12v2' of git://github.com/hisilicon/linux-hisi:
arm64: dts: hisilicon: hi3670.dtsi: add I2C settings
arm64: dts: hisilicon: hikey970-pinctrl.dtsi: add missing pinctrl settings
arm64: dts: hisilicon: hi3670.dtsi: add iomcu_rst
arm64: dts: hisilicon: delete unused property smmu-cb-memtype
arm64: dts: hisilicon: avoid irrelevant nodes being mistakenly identified as PHY nodes
arm64: dts: hisilicon: normalize the node name of the localbus
arm64: dts: hisilicon: normalize the node name of the module thermal
arm64: dts: hisilicon: place clock-names "bus" before "core"
arm64: dts: hisilicon: separate each group of data in the property "ranges"
Link: https://lore.kernel.org/r/6013D1C7.90902@hisilicon.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Mauro Carvalho Chehab [Fri, 15 Jan 2021 11:53:58 +0000 (12:53 +0100)]
arm64: dts: hisilicon: hi3670.dtsi: add I2C settings
The I2C buses are not declared at the device tree. As this will
be needed by further patches, add them, keeping all in
disabled state. Per-board settings can override it.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Wei Xu <xuwei5@hisilicon.com>
Mauro Carvalho Chehab [Fri, 15 Jan 2021 11:53:57 +0000 (12:53 +0100)]
arm64: dts: hisilicon: hikey970-pinctrl.dtsi: add missing pinctrl settings
There are several pinctrl settings that are missing at this
DT file.
Also, the entries are out of order.
Add the missing bits, as they'll be required by the DRM driver - and
probably by other drivers not upstreamed yet.
Reorder the entres, adding the missing bits.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Wei Xu <xuwei5@hisilicon.com>
Mauro Carvalho Chehab [Fri, 15 Jan 2021 11:53:56 +0000 (12:53 +0100)]
arm64: dts: hisilicon: hi3670.dtsi: add iomcu_rst
This is required in order to support USB.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Wei Xu <xuwei5@hisilicon.com>
Zhen Lei [Mon, 18 Jan 2021 03:16:34 +0000 (11:16 +0800)]
arm64: dts: hisilicon: delete unused property smmu-cb-memtype
The "smmu-cb-memtype" is a private property developed by the Hisilicon
driver in the early stage and is not used now. So delete it.
Otherwise, below YAML check warnings are reported:
arch/arm64/boot/dts/hisilicon/hip06-d03.dt.yaml: iommu@
a0040000: \
'smmu-cb-memtype' does not match any of the regexes: 'pinctrl-[0-9]+'
arch/arm64/boot/dts/hisilicon/hip07-d05.dt.yaml: iommu@
a0040000: \
'smmu-cb-memtype' does not match any of the regexes: 'pinctrl-[0-9]+'
Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com>
Signed-off-by: Wei Xu <xuwei5@hisilicon.com>
Zhen Lei [Mon, 18 Jan 2021 03:16:33 +0000 (11:16 +0800)]
arm64: dts: hisilicon: avoid irrelevant nodes being mistakenly identified as PHY nodes
Currently, the names of several nodes incorrectly match common PHY
provider schema. And the phy-provider.yaml requires them must have
property "#phy-cells". As a result, false positives similar to the
following are reported:
usb2-phy@120: '#phy-cells' is a required property
Change their names slightly so that they do not match pattern:
"^(|usb-|usb2-|usb3-|pci-|pcie-|sata-)phy(@[0-9a-f,]+)*$".
Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com>
Signed-off-by: Wei Xu <xuwei5@hisilicon.com>
Zhen Lei [Mon, 18 Jan 2021 03:16:32 +0000 (11:16 +0800)]
arm64: dts: hisilicon: normalize the node name of the localbus
Change the node name of the localbus to match
'^([a-z][a-z0-9\\-]+-bus|bus|soc|axi|ahb|apb)(@[0-9a-f]+)?$'. This error
is detected by simple-bus.yaml.
Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com>
Signed-off-by: Wei Xu <xuwei5@hisilicon.com>
Zhen Lei [Mon, 18 Jan 2021 03:16:31 +0000 (11:16 +0800)]
arm64: dts: hisilicon: normalize the node name of the module thermal
1. Change the node name of the thermal zone to match
'^[a-zA-Z][a-zA-Z0-9\\-]{1,12}-thermal$', add suffix "-thermal".
2. Change the node name of the trip point to match
'^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', delete character "@".
Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com>
Signed-off-by: Wei Xu <xuwei5@hisilicon.com>
Zhen Lei [Mon, 18 Jan 2021 03:16:30 +0000 (11:16 +0800)]
arm64: dts: hisilicon: place clock-names "bus" before "core"
Look at the clock-names schema defined in arm,mali-utgard.yaml:
clock-names:
items:
- const: bus
- const: core
The "bus" needs to be placed before the "core".
Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com>
Signed-off-by: Wei Xu <xuwei5@hisilicon.com>
Zhen Lei [Mon, 18 Jan 2021 03:16:29 +0000 (11:16 +0800)]
arm64: dts: hisilicon: separate each group of data in the property "ranges"
Do not write the "ranges" of multiple groups of data into a uint32 array,
use <> to separate them. Otherwise, the errors similar to the following
will be reported:
soc: pcie@
a0090000:ranges: [[
33554432, 0,
2986344448, 0,
2986344448, 0, \
100597760,
16777216, 0, 0, 0,
3086942208, 0, 65536]] is not valid under \
any of the given schemas (Possible causes of the failure):
soc: pcie@
a0090000:ranges: [[
33554432, 0,
2986344448, 0,
2986344448, 0, \
100597760,
16777216, 0, 0, 0,
3086942208, 0, 65536]] is not of type 'boolean'
soc: pcie@
a0090000:ranges:0: [
33554432, 0,
2986344448, 0,
2986344448, 0, \
100597760,
16777216, 0, 0, 0,
3086942208, 0, 65536] is too long
Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com>
Signed-off-by: Wei Xu <xuwei5@hisilicon.com>
Amelie Delaunay [Thu, 14 Jan 2021 13:15:24 +0000 (14:15 +0100)]
ARM: dts: stm32: add #clock-cells property to usbphyc node on stm32mp151
usbphyc is a 48Mhz clock provider: the clock can be used as clock source
for USB OTG. Add #clock-cells property to usbphyc node to reflect this
capability.
Signed-off-by: Amelie Delaunay <amelie.delaunay@foss.st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Amelie Delaunay [Thu, 14 Jan 2021 13:15:23 +0000 (14:15 +0100)]
ARM: dts: stm32: remove usbphyc ports vdda1v1 & vdda1v8 on stm32mp15 boards
vdda1v1 and vdda1v8 supplies are required by USB PLL, not by the PHYs.
Remove them from usbphyc child phy nodes now that they are managed in
usbphyc parent node at SoC level.
Cc: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Amelie Delaunay <amelie.delaunay@foss.st.com>
Tested-by: Marek Vasut <marex@denx.de>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Amelie Delaunay [Thu, 14 Jan 2021 13:15:22 +0000 (14:15 +0100)]
ARM: dts: stm32: add usbphyc vdda1v1 and vdda1v8 supplies on stm32mp151
vdda1v1 and vdda1v8 supplies are required by USB PLL. Add them in usbphyc
node.
Cc: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Amelie Delaunay <amelie.delaunay@foss.st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Jagan Teki [Wed, 23 Dec 2020 11:07:57 +0000 (16:37 +0530)]
ARM: dts: stm32: Add STM32MP1 I2C6 SDA/SCL pinmux
Add SDA/SCL pinmux lines for I2C6 on STM32MP1.
This support adds both in default and sleep states.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Geert Uytterhoeven [Thu, 28 Jan 2021 11:01:36 +0000 (12:01 +0100)]
arm64: dts: renesas: beacon: Fix EEPROM compatible value
"make dtbs_check" fails with:
arch/arm64/boot/dts/renesas/r8a774b1-beacon-rzg2n-kit.dt.yaml: eeprom@50: compatible: 'oneOf' conditional failed, one must be fixed:
'microchip,at24c64' does not match '^(atmel|catalyst|microchip|nxp|ramtron|renesas|rohm|st),(24(c|cs|lc|mac)[0-9]+|spd)$'
Fix this by dropping the bogus "at" prefix.
Fixes: a1d8a344f1ca0709 ("arm64: dts: renesas: Introduce r8a774a1-beacon-rzg2m-kit")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20210128110136.2293490-1-geert+renesas@glider.be
Arnd Bergmann [Tue, 26 Jan 2021 22:13:06 +0000 (23:13 +0100)]
Merge tag 'samsung-dt64-5.12' of git://git./linux/kernel/git/krzk/linux into arm/dt
Samsung DTS ARM64 changes for v5.12
Correct Samsung PMIC and S3FWRN5 NFC interrupts trigger levels on
TM2/TM2E and Espresso boards.
* tag 'samsung-dt64-5.12' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux:
arm64: dts: exynos: correct S3FWRN5 NFC interrupt trigger level on TM2
arm64: dts: exynos: correct PMIC interrupt trigger level on Espresso
arm64: dts: exynos: correct PMIC interrupt trigger level on TM2
Link: https://lore.kernel.org/r/20210125191240.11278-4-krzk@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Marek Vasut [Sun, 24 Jan 2021 17:03:37 +0000 (18:03 +0100)]
ARM: dts: stm32: Rename mmc controller nodes to mmc@
Per mmc-controller.yaml, the node pattern is "^mmc(@.*)?$" ,
so adjust the node.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Ludovic Barre <ludovic.barre@st.com>
Cc: Ulf Hansson <ulf.hansson@linaro.org>
Cc: linux-stm32@st-md-mailman.stormreply.com
Cc: devicetree@vger.kernel.org
Acked-by: Yann Gautier <yann.gautier@foss.st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Marek Vasut [Sun, 24 Jan 2021 17:02:58 +0000 (18:02 +0100)]
ARM: dts: stm32: Enable voltage translator auto-detection on DHCOM
The DHCOM SoM uSD slot has an optional voltage level translator, add
DT bindings which permit the MMCI driver to detect the translator
automatically.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Ludovic Barre <ludovic.barre@st.com>
Cc: Ulf Hansson <ulf.hansson@linaro.org>
Cc: linux-stm32@st-md-mailman.stormreply.com
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Marek Vasut [Sun, 24 Jan 2021 17:02:57 +0000 (18:02 +0100)]
ARM: dts: stm32: Add additional init state for SDMMC1 pins
Add "init" mux option for SDMMC1, where the CMD, CK, CKIN lines are not
configured, so they can be claimed as GPIOs early on in driver probe().
This is used for probing optional voltage level translator.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Ludovic Barre <ludovic.barre@st.com>
Cc: Ulf Hansson <ulf.hansson@linaro.org>
Cc: linux-stm32@st-md-mailman.stormreply.com
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Arnd Bergmann [Mon, 25 Jan 2021 10:17:56 +0000 (11:17 +0100)]
Merge tag 'visconti-arm-dt-for-v5.11-tag2' of git://git./linux/kernel/git/iwamatsu/linux-visconti into arm/dt
Visconti device tree updates for 5.11
- Add watchdog support for TMPV7708 SoC
- Add entries for Toshiba Visconti5 watchdog driver
* tag 'visconti-arm-dt-for-v5.11-tag2' of git://git.kernel.org/pub/scm/linux/kernel/git/iwamatsu/linux-visconti:
arm64: dts: visconti: Add watchdog support for TMPV7708 SoC
MAINTAINERS: Add entries for Toshiba Visconti5 watchdog driver
Link: https://lore.kernel.org/r/20210125003357.yd72y4f5vcdnvhnr@toshiba.co.jp
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Takeshi Saito [Mon, 25 Jan 2021 07:58:45 +0000 (08:58 +0100)]
arm64: dts: renesas: falcon: Enable MMC
Enable MMC on the Falcon board.
Signed-off-by: Takeshi Saito <takeshi.saito.xv@renesas.com>
Signed-off-by: Koji Matsuoka <koji.matsuoka.xm@renesas.com>
[wsa: double checked, rebased, slightly improved, moved to falcon-cpu]
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/20210125075845.3864-3-wsa+renesas@sang-engineering.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Takeshi Saito [Mon, 25 Jan 2021 07:58:44 +0000 (08:58 +0100)]
arm64: dts: renesas: r8a779a0: Add MMC node
Add a device node for MMC.
Signed-off-by: Takeshi Saito <takeshi.saito.xv@renesas.com>
Signed-off-by: Koji Matsuoka <koji.matsuoka.xm@renesas.com>
[wsa: double checked & rebased]
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/20210125075845.3864-2-wsa+renesas@sang-engineering.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Linh Phung [Thu, 21 Jan 2021 11:00:07 +0000 (12:00 +0100)]
arm64: dts: renesas: r8a779a0: Add HSCIF support
Define the generic parts of the HSCIF[0-3] device nodes.
Signed-off-by: Linh Phung <linh.phung.jy@renesas.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Link: https://lore.kernel.org/r/20210121110008.15894-4-wsa+renesas@sang-engineering.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Wolfram Sang [Thu, 21 Jan 2021 11:00:06 +0000 (12:00 +0100)]
arm64: dts: renesas: falcon: Complete SCIF0 nodes
SCIF0 has been enabled by the firmware, so it worked already. Still, add
the proper nodes to make it work in any case.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/20210121110008.15894-3-wsa+renesas@sang-engineering.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Wolfram Sang [Thu, 21 Jan 2021 11:00:05 +0000 (12:00 +0100)]
arm64: dts: renesas: r8a779a0: Add & update SCIF nodes
This is the result of multiple patches taken from the BSP, combined,
rebased, and properly sorted. SCIF0 gets DMA properties, other SCIFs are
entirely new.
Signed-off-by: Linh Phung <linh.phung.jy@renesas.com>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/20210121110008.15894-2-wsa+renesas@sang-engineering.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Wolfram Sang [Thu, 21 Jan 2021 10:06:18 +0000 (11:06 +0100)]
arm64: dts: renesas: falcon: Add Ethernet-AVB0 support
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/20210121100619.5653-5-wsa+renesas@sang-engineering.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Tho Vu [Thu, 21 Jan 2021 10:06:17 +0000 (11:06 +0100)]
arm64: dts: renesas: r8a779a0: Add Ethernet-AVB support
Define the generic parts of Ethernet-AVB device nodes. Only AVB0 was
tested because it was the only port with a PHY on current hardware.
Signed-off-by: Tho Vu <tho.vu.wh@renesas.com>
[wsa: double checked, rebased, added "internal-delay" properties]
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/20210121100619.5653-4-wsa+renesas@sang-engineering.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Wolfram Sang [Thu, 21 Jan 2021 09:54:19 +0000 (10:54 +0100)]
arm64: dts: renesas: falcon: Add I2C0,1,6 support
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/20210121095420.5023-4-wsa+renesas@sang-engineering.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Koji Matsuoka [Thu, 21 Jan 2021 09:54:18 +0000 (10:54 +0100)]
arm64: dts: renesas: r8a779a0: Add I2C nodes
Add I2C devicetree description to V3U
Signed-off-by: Koji Matsuoka <koji.matsuoka.xm@renesas.com>
[wsa: rebased and double checked]
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/20210121095420.5023-3-wsa+renesas@sang-engineering.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Wolfram Sang [Tue, 19 Jan 2021 13:33:22 +0000 (14:33 +0100)]
arm64: dts: renesas: Disable SD functions for plain eMMC
Some SDHI instances are solely used for eMMC. Disable SD and SDIO
for faster initialization.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Adam Ford <aford173@gmail.com> (beacon)
Link: https://lore.kernel.org/r/20210119133322.87289-1-wsa+renesas@sang-engineering.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Nobuhiro Iwamatsu [Tue, 1 Dec 2020 09:39:07 +0000 (18:39 +0900)]
arm64: dts: visconti: Add watchdog support for TMPV7708 SoC
Add watchdog node in TMPV7708's dtsi, and tmpv7708-rm-mbrc boards's
dts.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro1.iwamatsu@toshiba.co.jp>
Nobuhiro Iwamatsu [Tue, 1 Dec 2020 09:34:24 +0000 (18:34 +0900)]
MAINTAINERS: Add entries for Toshiba Visconti5 watchdog driver
Add entries for Toshiba Visconti5 watchdog driver and binding.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro1.iwamatsu@toshiba.co.jp>
Linus Walleij [Fri, 22 Jan 2021 22:20:38 +0000 (23:20 +0100)]
ARM: dts: nomadik: Fix up MMC node names
Fix the node names for the MMC/SD card controller to conform
to the standard node name mmc@..
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20210122222038.2888747-1-linus.walleij@linaro.org'
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Arnd Bergmann [Fri, 22 Jan 2021 22:37:20 +0000 (23:37 +0100)]
Merge tag 'ux500-dts-v5.12' of git://git./linux/kernel/git/linusw/linux-nomadik into arm/dt
Ux500 DTS updates for the v5.12 kernel cycle:
- A new DTS file for the Samsung GT-I9070 (Janice)
- Fix up ADC channel name attributes
- Add charger interrupts
- Add thermistors to the HREF boards
- Remove the non-existing AB8505 HW ADC IRQ
- Push down the VMMCI setting to each board
- Add the die temperature channel to teh AB8505
- Fix up the MMC host names to follow the standard
naming convention
* tag 'ux500-dts-v5.12' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-nomadik:
ARM: dts: Fix up MMC host node names
ARM: dts: ux500: Add die temperature to AB8505
ARM: dts: ux500: Push VMMCI down to each tree
ARM: dts: ux500: Remove the GPADC HW IRQ
ARM: dts: ux500: Add thermistors to the HREF
ARM: dts: ux500: Add interrupts to charger
ARM: dts: ux500: Fix channel names attributes
ARM: dts: ux500: Add a device tree for Janice
Link: https://lore.kernel.org/r/CACRpkdbn=P63V9aEO2wKu2DwvVUcbjwCEV_JvKwWZ0netT75ig@mail.gmail.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Linus Walleij [Wed, 13 Jan 2021 20:17:45 +0000 (21:17 +0100)]
ARM: dts: Fix up MMC host node names
The standard mandates that these nodes be named
mmc@... not sdi_foo@...
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Daniel Palmer [Thu, 24 Dec 2020 02:03:54 +0000 (11:03 +0900)]
ARM: mstar: Unify common parts of BreadBee boards into a dtsi
The BreadBee and the BreadBee Crust are the same PCB with a different
SoC mounted. There are two top level dts to handle this.
To avoid deduplicating the parts that are more related to the PCB than
the SoC (i.e. the voltage regs and LEDs) add a common dtsi that can
be included in both top level dts.
Signed-off-by: Daniel Palmer <daniel@0x0f.com>
Link: https://lore.kernel.org/r/20201224020354.2212037-1-daniel@0x0f.com'
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Arnd Bergmann [Fri, 22 Jan 2021 15:03:21 +0000 (16:03 +0100)]
Merge tag 'at91-dt-5.12' of git://git./linux/kernel/git/at91/linux into arm/dt
AT91 DT for 5.12:
- removing a property never documented nor used
- adding i2c recovery GPI for one more board
* tag 'at91-dt-5.12' of git://git.kernel.org/pub/scm/linux/kernel/git/at91/linux:
ARM: dts: at91: sama5d2: remove atmel,wakeup-type references
ARM: dts: at91-sama5d27_wlsom1: add i2c recovery
Link: https://lore.kernel.org/r/20210122145056.171283-1-nicolas.ferre@microchip.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Arnd Bergmann [Fri, 22 Jan 2021 14:02:34 +0000 (15:02 +0100)]
Merge tag 'socfpga_dts_update_for_v5.12' of git://git./linux/kernel/git/dinguyen/linux into arm/dt
SoCFPGA DTS updates for v5.12
- Add DTS file for eASIC N5X platform
- Use generic ngpios in GPIO entries
- Add PMU node for Arria10
* tag 'socfpga_dts_update_for_v5.12' of git://git.kernel.org/pub/scm/linux/kernel/git/dinguyen/linux:
ARM: dts: arria10: add PMU node
arm64: dts: n5x: Add support for Intel's eASIC N5X platform
arm64: dts: socfpga: Use generic "ngpios" rather than "snps,nr-gpios"
Link: https://lore.kernel.org/r/20210120012334.25730-1-dinguyen@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Claudiu Beznea [Tue, 5 Jan 2021 11:18:45 +0000 (13:18 +0200)]
ARM: dts: at91: sama5d2: remove atmel,wakeup-type references
atmel,wakeup-type DT property is not referenced anywhere in the current
and previous version of the code thus remove it.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Nicolas Ferre <nferre@kernel.org>
Link: https://lore.kernel.org/r/1609845525-10766-1-git-send-email-claudiu.beznea@microchip.com
Nicolas Ferre [Sun, 17 Jan 2021 18:35:58 +0000 (19:35 +0100)]
ARM: dts: at91-sama5d27_wlsom1: add i2c recovery
Add the i2c gpio pinctrls to support the i2c bus recovery on this board.
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Reviewed-by: Codrin Ciubotariu <codrin.ciubotariu@microchip.com>
Link: https://lore.kernel.org/r/20210117183558.5369-1-nicolas.ferre@microchip.com
Koji Matsuoka [Fri, 8 Jan 2021 10:43:45 +0000 (11:43 +0100)]
arm64: dts: renesas: r8a779a0: Add MSIOF device nodes
Add device nodes for the Clock-Synchronized Serial Interface with
FIFO (MSIOF) instances on the Renesas R-Car V3U (r8a779a0) SoC.
Signed-off-by: Koji Matsuoka <koji.matsuoka.xm@renesas.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20210108104345.2026857-1-geert+renesas@glider.be
Daniel Palmer [Sat, 12 Dec 2020 01:22:53 +0000 (10:22 +0900)]
dt-bindings: vendor-prefixes: Fix misordering introduced by honestar prefix
The prefix for honestar should come before honeywell.
Fixes: 43181b5d8072 ("dt-bindings: vendor-prefixes: Add honestar vendor prefix")
Signed-off-by: Daniel Palmer <daniel@0x0f.com>
Link: https://lore.kernel.org/linux-arm-kernel/CAFr9PXmwOEuHHA-kDeL1YS8bWvovrt43MXxyy1J+hGbXwPUFSA@mail.gmail.com/
Link: https://lore.kernel.org/r/20201212012253.373074-1-daniel@0x0f.com'
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Arnd Bergmann [Fri, 15 Jan 2021 16:40:50 +0000 (17:40 +0100)]
Merge tag 'renesas-dt-bindings-for-v5.12-tag1' of git://git./linux/kernel/git/geert/renesas-devel into arm/dt
Renesas DT binding updates for v5.12
- Document suport for the Beacon EmbeddedWorks RZ/G2N and RZ/H kits.
* tag 'renesas-dt-bindings-for-v5.12-tag1' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-devel:
dt-bindings: arm: renesas: Add Beacon RZ/G2N and RZ/G2H boards
Link: https://lore.kernel.org/r/20210115094610.2334058-3-geert+renesas@glider.be
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Arnd Bergmann [Fri, 15 Jan 2021 15:39:46 +0000 (16:39 +0100)]
Merge tag 'renesas-arm-dt-for-v5.12-tag1' of git://git./linux/kernel/git/geert/renesas-devel into arm/dt
Renesas ARM DT updates for v5.12
- Timer (CMT/TMU) support for R-Car Gen3 SoCs,
- Watchdog (RWDT), pincontrol (PFC), GPIO, and DMA (SYS-DMAC) support
for the R-Car V3U SoC,
- USB2 clock selector and SPI Multi I/O Bus Controller (RPC-IF)
support for RZ/G2 SoCs,
- Support for the Beacon EmbeddedWorks RZ/G2H and RZ/G2N kits,
- Various fixes and improvements.
* tag 'renesas-arm-dt-for-v5.12-tag1' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-devel: (24 commits)
arm64: dts: renesas: r8a779a0: Add SYS-DMAC nodes
arm64: dts: renesas: r8a779a0: Add GPIO nodes
arm64: dts: renesas: r8a779a0: Add pinctrl device node
arm64: dts: renesas: rzg2: Add RPC-IF Support
arm64: dts: renesas: rzg2: Add usb2_clksel to RZ/G2 M/N/H
arm64: dts: renesas: r8a774e1: Introduce beacon-rzg2h-kit
arm64: dts: renesas: r8a774b1: Introduce beacon-rzg2n-kit
arm64: dts: renesas: beacon-rzg2m-kit: Rearrange SoC unique functions
arm64: dts: renesas: beacon: Better describe keys
arm64: dts: renesas: beacon: Configure Audio CODEC clocks
arm64: dts: renesas: beacon kit: Fix Audio Clock sources
arm64: dts: renesas: beacon: Configure programmable clocks
arm64: dts: renesas: falcon: Enable watchdog timer
arm64: dts: renesas: r8a779a0: Add RWDT node
arm64: dts: renesas: beacon: Correct I2C bus speeds
arm64: dts: renesas: beacon: Enable SPI
arm64: dts: renesas: beacon: Don't make vccq_sdhi0 always on
arm64: dts: renesas: beacon: Fix RGB Display PWM Backlight
arm64: dts: renesas: beacon: Fix LVDS PWM Backlight
arm64: dts: renesas: beacon: Fix audio-1.8V pin enable
...
Link: https://lore.kernel.org/r/20210115094610.2334058-2-geert+renesas@glider.be
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Marek Vasut [Thu, 24 Dec 2020 06:27:26 +0000 (07:27 +0100)]
ARM: dts: stm32: Disable KS8851 and FMC on PicoITX board
The PicoITX has only one ethernet routed out, so the KS8851 is not used
at all. Disable the KS8851 and the entire FMC controller.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: linux-stm32@st-md-mailman.stormreply.com
To: linux-arm-kernel@lists.infradead.org
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Alexander Dahl [Mon, 28 Dec 2020 16:32:16 +0000 (17:32 +0100)]
ARM: dts: stm32: Fix schema warnings for pwm-leds on lxa-mc1
The node names for devices using the pwm-leds driver follow a certain
naming scheme (now). Parent node name is not enforced, but recommended
by DT project.
DTC arch/arm/boot/dts/stm32mp157c-lxa-mc1.dt.yaml
CHECK arch/arm/boot/dts/stm32mp157c-lxa-mc1.dt.yaml
/home/alex/build/linux/arch/arm/boot/dts/stm32mp157c-lxa-mc1.dt.yaml: led-rgb: 'led-blue', 'led-green', 'led-red' do not match any of the regexes: '^led(-[0-9a-f]+)?$', 'pinctrl-[0-9]+'
From schema: /home/alex/src/linux/leds/Documentation/devicetree/bindings/leds/leds-pwm.yaml
Signed-off-by: Alexander Dahl <post@lespocky.de>
Acked-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Marek Vasut [Thu, 14 Jan 2021 14:52:10 +0000 (15:52 +0100)]
ARM: dts: stm32: Disable SDMMC1 CKIN feedback clock on DHCOM
The STM32MP1 DHCOM SoM can be built with either bus voltage level shifter
or without one on the SDMMC1 interface. Because the SDMMC1 interface is
limited to 50 MHz and hence SD high-speed anyway, disable the SD feedback
clock to permit operation of the same U-Boot image on both SoM with and
without voltage level shifter.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: linux-stm32@st-md-mailman.stormreply.com
To: linux-arm-kernel@lists.infradead.org
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Marek Vasut [Tue, 1 Dec 2020 11:14:40 +0000 (12:14 +0100)]
ARM: dts: stm32: Enable internal pull-ups for SDMMC1 on DHCOM SoM
The default state of SD bus and clock line is logical HI. SD card IO is
open-drain and pulls the bus lines LO. Always enable the SD bus pull ups
to guarantee this behavior on DHCOM SoM. Note that on SoMs with SD bus
voltage level shifter, the pull ups are built into the level shifter,
however that has no negative impact.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: linux-stm32@st-md-mailman.stormreply.com
To: linux-arm-kernel@lists.infradead.org
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Marek Vasut [Tue, 29 Dec 2020 17:55:21 +0000 (18:55 +0100)]
ARM: dts: stm32: Fix GPIO hog flags on DHCOM DRC02
The GPIO hog flags are ignored by gpiolib-of.c now, set the flags to 0.
Since GPIO_ACTIVE_HIGH is defined as 0, this change only increases the
correctness of the DT.
Fixes: fde180f06d7b ("ARM: dts: stm32: Add DHSOM based DRC02 board")
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: linux-stm32@st-md-mailman.stormreply.com
To: linux-arm-kernel@lists.infradead.org
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Marek Vasut [Tue, 29 Dec 2020 17:55:20 +0000 (18:55 +0100)]
ARM: dts: stm32: Fix GPIO hog flags on DHCOM PicoITX
The GPIO hog flags are ignored by gpiolib-of.c now, set the flags to 0.
Due to a change in gpiolib-of.c, setting flags to GPIO_ACTIVE_LOW and
using output-low DT property leads to the GPIO being set high instead.
Fixes: ac68793f49de ("ARM: dts: stm32: Add DHCOM based PicoITX board")
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: linux-stm32@st-md-mailman.stormreply.com
To: linux-arm-kernel@lists.infradead.org
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Marek Vasut [Thu, 24 Dec 2020 06:24:38 +0000 (07:24 +0100)]
ARM: dts: stm32: Fix GPIO hog names on DHCOM
The GPIO hog node name should match regex '^(hog-[0-9]+|.+-hog(-[0-9]+)?)$',
make it so and fix the following two make dtbs_check warnings:
arch/arm/boot/dts/stm32mp157c-dhcom-picoitx.dt.yaml: hog-usb-port-power: $nodename:0: 'hog-usb-port-power' does not match '^(hog-[0-9]+|.+-hog(-[0-9]+)?)$'
arch/arm/boot/dts/stm32mp153c-dhcom-drc02.dt.yaml: hog-usb-hub: $nodename:0: 'hog-usb-hub' does not match '^(hog-[0-9]+|.+-hog(-[0-9]+)?)$'
Fixes: ac68793f49de ("ARM: dts: stm32: Add DHCOM based PicoITX board")
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: linux-stm32@st-md-mailman.stormreply.com
To: linux-arm-kernel@lists.infradead.org
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Marek Vasut [Thu, 7 Jan 2021 15:07:42 +0000 (16:07 +0100)]
ARM: dts: stm32: Disable optional TSC2004 on DRC02 board
The DRC02 has no use for the on-SoM touchscreen controller, and the
on-SoM touchscreen controller may not even be populated, which then
results in error messages in kernel log. Disable the touchscreen
controller in DT.
Fixes: fde180f06d7b ("ARM: dts: stm32: Add DHSOM based DRC02 board")
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: linux-stm32@st-md-mailman.stormreply.com
To: linux-arm-kernel@lists.infradead.org
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Marek Vasut [Tue, 1 Dec 2020 11:13:31 +0000 (12:13 +0100)]
ARM: dts: stm32: Disable WP on DHCOM uSD slot
The uSD slot has no WP detection, disable it.
Fixes: 34e0c7847dcf ("ARM: dts: stm32: Add DH Electronics DHCOM STM32MP1 SoM and PDK2 board")
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: linux-stm32@st-md-mailman.stormreply.com
To: linux-arm-kernel@lists.infradead.org
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Marek Vasut [Tue, 1 Dec 2020 11:13:30 +0000 (12:13 +0100)]
ARM: dts: stm32: Connect card-detect signal on DHCOM
The DHCOM SoM uSD slot card detect signal is connected to GPIO PG1,
describe it in the DT.
Fixes: 34e0c7847dcf ("ARM: dts: stm32: Add DH Electronics DHCOM STM32MP1 SoM and PDK2 board")
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: linux-stm32@st-md-mailman.stormreply.com
To: linux-arm-kernel@lists.infradead.org
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Marek Vasut [Tue, 1 Dec 2020 11:13:29 +0000 (12:13 +0100)]
ARM: dts: stm32: Fix polarity of the DH DRC02 uSD card detect
The uSD card detect signal on the DH DRC02 is active-high, with
a default pull down resistor on the board. Invert the polarity.
Fixes: fde180f06d7b ("ARM: dts: stm32: Add DHSOM based DRC02 board")
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: linux-stm32@st-md-mailman.stormreply.com
To: linux-arm-kernel@lists.infradead.org
--
Note that this could not be tested on prototype SoMs, now that it is
tested, this issue surfaced, so it needs to be fixed.
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Geert Uytterhoeven [Thu, 7 Jan 2021 18:20:45 +0000 (19:20 +0100)]
arm64: dts: renesas: r8a779a0: Add SYS-DMAC nodes
Add device nodes for the Direct Memory Access Controller for System
(SYS-DMAC) instances on the Renesas R-Car V3U (r8a779a0) SoC.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20210107182045.1948037-1-geert+renesas@glider.be
Geert Uytterhoeven [Thu, 14 Jan 2021 11:11:17 +0000 (12:11 +0100)]
arm64: dts: renesas: r8a779a0: Add GPIO nodes
Add device nodes for the General Purpose Input/Output (GPIO) block on
the Renesas R-Car V3U (r8a779a0) SoC.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/20210114111117.2214281-1-geert+renesas@glider.be
Ulrich Hecht [Tue, 12 Jan 2021 16:59:48 +0000 (17:59 +0100)]
arm64: dts: renesas: r8a779a0: Add pinctrl device node
This patch adds the pinctrl device node for the R8A779A0 (V3U) SoC.
Signed-off-by: Ulrich Hecht <uli+renesas@fpond.eu>
Link: https://lore.kernel.org/r/20210112165948.31162-1-uli+renesas@fpond.eu
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Linus Walleij [Mon, 21 Dec 2020 12:20:26 +0000 (13:20 +0100)]
ARM: dts: ux500: Add die temperature to AB8505
The AB8505 mixed signal ASIC variant has a die temperature
channel that is missing in the AB8500 variant. Add it to
the DTSI.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Linus Walleij [Sat, 19 Dec 2020 20:31:55 +0000 (21:31 +0100)]
ARM: dts: ux500: Push VMMCI down to each tree
The setting of VMMCI differs so much between different
boards that we need to handle it on a per-board basis
rather that complicating things by overriding stuff from
the included DTSI:s. Push it down into top-level tree
instead.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Linus Walleij [Fri, 18 Dec 2020 22:20:50 +0000 (23:20 +0100)]
ARM: dts: ux500: Remove the GPADC HW IRQ
The AB8505 variant lacks the hardware conversion IRQ, so
do not put it in with this variant.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Linus Walleij [Sat, 12 Dec 2020 10:46:26 +0000 (11:46 +0100)]
ARM: dts: ux500: Add thermistors to the HREF
This adds the two temperature-monitoring thermistors to the
HREF reference design, defines a thermal zone for the
chassis and sets some reasonable thermal limits.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Linus Walleij [Thu, 10 Dec 2020 15:17:21 +0000 (16:17 +0100)]
ARM: dts: ux500: Add interrupts to charger
The different charger nodes in the AB8500 and AB8505
includes was missing the interrupt assignments for the
interrupts necessary to drive the AB8500/AB8505 charging
state machine.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Linus Walleij [Tue, 8 Dec 2020 21:06:24 +0000 (22:06 +0100)]
ARM: dts: ux500: Fix channel names attributes
The AB8500/AB8505 is providing ADC channels and do so
using the standard property "io-channel-names" not the
mistakenly singular form "io-channel-name".
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Linus Walleij [Sun, 1 Nov 2020 23:22:40 +0000 (00:22 +0100)]
ARM: dts: ux500: Add a device tree for Janice
This adds a basic device tree for the Samsung GT-I9070
mobile phone also known as Janice.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Adam Ford [Sat, 2 Jan 2021 11:54:12 +0000 (05:54 -0600)]
arm64: dts: renesas: rzg2: Add RPC-IF Support
The RZ/G2 series contain the SPI Multi I/O Bus Controller (RPC-IF).
Add the nodes, but make them disabled by default.
Signed-off-by: Adam Ford <aford173@gmail.com>
Link: https://lore.kernel.org/r/20210102115412.3402059-4-aford173@gmail.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Adam Ford [Mon, 28 Dec 2020 20:22:21 +0000 (14:22 -0600)]
arm64: dts: renesas: rzg2: Add usb2_clksel to RZ/G2 M/N/H
Per the reference manual for the RZ/G Series, 2nd Generation,
the RZ/G2M, RZ/G2N, and RZ/G2H have a bit that can be set to
choose between a crystal oscillator and an external oscillator.
Because only boards that need this should enable it, it's marked
as disabled by default for backwards compatibility with existing
boards.
Signed-off-by: Adam Ford <aford173@gmail.com>
Link: https://lore.kernel.org/r/20201228202221.2327468-2-aford173@gmail.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Adam Ford [Thu, 24 Dec 2020 17:05:01 +0000 (11:05 -0600)]
arm64: dts: renesas: r8a774e1: Introduce beacon-rzg2h-kit
Beacon EmbeddedWorks is introducing a new kit based on the
RZ/G2H SoC from Renesas.
The SOM supports eMMC, WiFi and Bluetooth, along with a Cat-M1
cellular radio.
The Baseboard has Ethernet, USB, HDMI, stereo audio in and out,
along with a variety of push buttons and LED's, and support for
a parallel RGB and an LVDS display. It uses the same baseboard
and SOM files as the RZ/G2M and RZ/G2N kits.
Signed-off-by: Adam Ford <aford173@gmail.com>
Link: https://lore.kernel.org/r/20201224170502.2254683-8-aford173@gmail.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Adam Ford [Thu, 24 Dec 2020 17:05:00 +0000 (11:05 -0600)]
arm64: dts: renesas: r8a774b1: Introduce beacon-rzg2n-kit
Beacon EmbeddedWorks is introducing a new kit based on the
RZ/G2N SoC from Renesas.
The SOM supports eMMC, WiFi and Bluetooth, along with a Cat-M1
cellular radio.
The Baseboard has Ethernet, USB, HDMI, stereo audio in and out,
along with a variety of push buttons and LED's, and support for
a parallel RGB and an LVDS display. It uses the same baseboard
and SOM as the RZ/G2M.
This SOM has only 2GB of DDR, and beacon-renesom-som.dtsi contains
the base memory node, so an additional memory node isn't necessary.
Signed-off-by: Adam Ford <aford173@gmail.com>
Link: https://lore.kernel.org/r/20201224170502.2254683-7-aford173@gmail.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Adam Ford [Thu, 24 Dec 2020 17:04:59 +0000 (11:04 -0600)]
arm64: dts: renesas: beacon-rzg2m-kit: Rearrange SoC unique functions
In preparation for adding new dev kits, move anything specific to the
RZ/G2M from the SOM-level and baseboard-levels and move them to the
kit-level. This allows the SOM and baseboard to be reused with
other SoC's.
Signed-off-by: Adam Ford <aford173@gmail.com>
Link: https://lore.kernel.org/r/20201224170502.2254683-6-aford173@gmail.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Adam Ford [Thu, 24 Dec 2020 17:04:57 +0000 (11:04 -0600)]
arm64: dts: renesas: beacon: Better describe keys
The keys on the baseboard are laid out in an diamond pattern, up, down,
left, right and center. Update the descriptions to make it easier to
read.
Signed-off-by: Adam Ford <aford173@gmail.com>
Link: https://lore.kernel.org/r/20201224170502.2254683-4-aford173@gmail.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Adam Ford [Thu, 24 Dec 2020 17:04:56 +0000 (11:04 -0600)]
arm64: dts: renesas: beacon: Configure Audio CODEC clocks
With the newly added configurable clock options, the audio CODEC can
configure the mclk automatically. Add the reference to the versaclock.
Since the devices on I2C5 can communicate at 400KHz, let's also increase
that too
Signed-off-by: Adam Ford <aford173@gmail.com>
Link: https://lore.kernel.org/r/20201224170502.2254683-3-aford173@gmail.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Adam Ford [Thu, 24 Dec 2020 17:04:55 +0000 (11:04 -0600)]
arm64: dts: renesas: beacon kit: Fix Audio Clock sources
The SoC was expecting two clock sources with different frequencies.
One to support 44.1KHz and one to support 48KHz. With the newly added
ability to configure the programmable clock, configure both clocks.
Assign the rcar-sound clocks to reference the versaclock instead of
the fixed clock.
Signed-off-by: Adam Ford <aford173@gmail.com>
Link: https://lore.kernel.org/r/20201224170502.2254683-2-aford173@gmail.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Adam Ford [Thu, 24 Dec 2020 17:04:54 +0000 (11:04 -0600)]
arm64: dts: renesas: beacon: Configure programmable clocks
When the board was added, clock drivers were being updated done at
the same time to allow the versaclock driver to properly configure
the modes. Unfortunately, the updates were not applied to the board
files at the time they should have been, so do it now.
Signed-off-by: Adam Ford <aford173@gmail.com>
Link: https://lore.kernel.org/r/20201224170502.2254683-1-aford173@gmail.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Arnd Bergmann [Fri, 8 Jan 2021 15:59:37 +0000 (16:59 +0100)]
Merge tag 'v5.11-berlin-dts' of git://git./linux/kernel/git/jszhang/linux-berlin into arm/dt
v5.11-berlin-dts
* tag 'v5.11-berlin-dts' of git://git.kernel.org/pub/scm/linux/kernel/git/jszhang/linux-berlin:
ARM: dts: berlin: Use generic "ngpios" rather than "snps,nr-gpios"
ARM: dts: berlin: Fix schema warnings for pwm-leds
Link: https://lore.kernel.org/r/20201211100521.2e6f4faa@xhacker.debian
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Arnd Bergmann [Fri, 8 Jan 2021 15:58:49 +0000 (16:58 +0100)]
Merge tag 'v5.11-berlin-dts64' of git://git./linux/kernel/git/jszhang/linux-berlin into arm/dt
v5.11-berlin-dts64
* tag 'v5.11-berlin-dts64' of git://git.kernel.org/pub/scm/linux/kernel/git/jszhang/linux-berlin:
arm64: dts: synaptics: Use generic "ngpios" rather than "snps,nr-gpios"
Link: https://lore.kernel.org/r/20201211100235.2b0b795b@xhacker.debian
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Dinh Nguyen [Tue, 5 Jan 2021 20:55:20 +0000 (14:55 -0600)]
ARM: dts: arria10: add PMU node
Add the PMU node for Arria10.
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
Dinh Nguyen [Mon, 7 Dec 2020 20:43:01 +0000 (14:43 -0600)]
arm64: dts: n5x: Add support for Intel's eASIC N5X platform
The Intel eASIC N5X platform shares the same register map as the Agilex
platform, thus, we can re-use the socfpga_agilex.dtsi as the base
DTSI.
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
Jisheng Zhang [Mon, 9 Nov 2020 09:03:35 +0000 (17:03 +0800)]
arm64: dts: socfpga: Use generic "ngpios" rather than "snps,nr-gpios"
This is to remove similar errors as below:
OF: /.../gpio-port@0: could not find phandle
Commit
7569486d79ae ("gpio: dwapb: Add ngpios DT-property support")
explained the reason of above errors well and added the generic
"ngpios" property, let's use it.
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
Linus Torvalds [Sun, 3 Jan 2021 23:55:30 +0000 (15:55 -0800)]
Linux 5.11-rc2
Linus Torvalds [Sat, 2 Jan 2021 20:22:46 +0000 (12:22 -0800)]
Merge tag 's390-5.11-3' of git://git./linux/kernel/git/s390/linux
Pull s390 cleanups from Vasily Gorbik:
"Update defconfigs and sort config select list"
* tag 's390-5.11-3' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
s390/Kconfig: sort config S390 select list once again
s390: update defconfigs
Linus Torvalds [Sat, 2 Jan 2021 19:53:05 +0000 (11:53 -0800)]
Merge tag 'pm-5.11-rc2' of git://git./linux/kernel/git/rafael/linux-pm
Pull power management fixes from Rafael Wysocki:
"These fix a crash in intel_pstate during resume from suspend-to-RAM
that may occur after recent changes and two resource leaks in error
paths in the operating performance points (OPP) framework, add a new
C-states table to intel_idle and update the cpuidle MAINTAINERS entry
to cover the governors too.
Specifics:
- Fix recently introduced crash in the intel_pstate driver that
occurs if scale-invariance is disabled during resume from
suspend-to-RAM due to inconsistent changes of APERF or MPERF MSR
values made by the platform firmware (Rafael Wysocki).
- Fix a memory leak and add a missing clk_put() in error paths in the
OPP framework (Quanyang Wang, Viresh Kumar).
- Add new C-states table for SnowRidge processors to the intel_idle
driver (Artem Bityutskiy).
- Update the MAINTAINERS entry for cpuidle to make it clear that the
governors are covered by it too (Lukas Bulwahn)"
* tag 'pm-5.11-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
intel_idle: add SnowRidge C-state table
cpufreq: intel_pstate: Fix fast-switch fallback path
opp: Call the missing clk_put() on error
opp: fix memory leak in _allocate_opp_table
MAINTAINERS: include governors into CPU IDLE TIME MANAGEMENT FRAMEWORK
Rafael J. Wysocki [Sat, 2 Jan 2021 09:16:32 +0000 (10:16 +0100)]
Merge branches 'pm-cpufreq' and 'pm-cpuidle'
* pm-cpufreq:
cpufreq: intel_pstate: Fix fast-switch fallback path
* pm-cpuidle:
intel_idle: add SnowRidge C-state table
MAINTAINERS: include governors into CPU IDLE TIME MANAGEMENT FRAMEWORK
Linus Torvalds [Fri, 1 Jan 2021 20:58:07 +0000 (12:58 -0800)]
Merge tag 'scsi-fixes' of git://git./linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"This is a load of driver fixes (12 ufs, 1 mpt3sas, 1 cxgbi).
The big core two fixes are for power management ("block: Do not accept
any requests while suspended" and "block: Fix a race in the runtime
power management code") which finally sorts out the resume problems
we've occasionally been having.
To make the resume fix, there are seven necessary precursors which
effectively renames REQ_PREEMPT to REQ_PM, so every "special" request
in block is automatically a power management exempt one.
All of the non-PM preempt cases are removed except for the one in the
SCSI Parallel Interface (spi) domain validation which is a genuine
case where we have to run requests at high priority to validate the
bus so this becomes an autopm get/put protected request"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (22 commits)
scsi: cxgb4i: Fix TLS dependency
scsi: ufs: Un-inline ufshcd_vops_device_reset function
scsi: ufs: Re-enable WriteBooster after device reset
scsi: ufs-mediatek: Use correct path to fix compile error
scsi: mpt3sas: Signedness bug in _base_get_diag_triggers()
scsi: block: Do not accept any requests while suspended
scsi: block: Remove RQF_PREEMPT and BLK_MQ_REQ_PREEMPT
scsi: core: Only process PM requests if rpm_status != RPM_ACTIVE
scsi: scsi_transport_spi: Set RQF_PM for domain validation commands
scsi: ide: Mark power management requests with RQF_PM instead of RQF_PREEMPT
scsi: ide: Do not set the RQF_PREEMPT flag for sense requests
scsi: block: Introduce BLK_MQ_REQ_PM
scsi: block: Fix a race in the runtime power management code
scsi: ufs-pci: Enable UFSHCD_CAP_RPM_AUTOSUSPEND for Intel controllers
scsi: ufs-pci: Fix recovery from hibernate exit errors for Intel controllers
scsi: ufs-pci: Ensure UFS device is in PowerDown mode for suspend-to-disk ->poweroff()
scsi: ufs-pci: Fix restore from S4 for Intel controllers
scsi: ufs-mediatek: Keep VCC always-on for specific devices
scsi: ufs: Allow regulators being always-on
scsi: ufs: Clear UAC for RPMB after ufshcd resets
...
Linus Torvalds [Fri, 1 Jan 2021 20:49:09 +0000 (12:49 -0800)]
Merge tag 'block-5.11-2021-01-01' of git://git.kernel.dk/linux-block
Pull block fixes from Jens Axboe:
"Two minor block fixes from this last week that should go into 5.11:
- Add missing NOWAIT debugfs definition (Andres)
- Fix kerneldoc warning introduced this merge window (Randy)"
* tag 'block-5.11-2021-01-01' of git://git.kernel.dk/linux-block:
block: add debugfs stanza for QUEUE_FLAG_NOWAIT
fs: block_dev.c: fix kernel-doc warnings from struct block_device changes
Linus Torvalds [Fri, 1 Jan 2021 20:29:49 +0000 (12:29 -0800)]
Merge tag 'io_uring-5.11-2021-01-01' of git://git.kernel.dk/linux-block
Pull io_uring fixes from Jens Axboe:
"A few fixes that should go into 5.11, all marked for stable as well:
- Fix issue around identity COW'ing and users that share a ring
across processes
- Fix a hang associated with unregistering fixed files (Pavel)
- Move the 'process is exiting' cancelation a bit earlier, so
task_works aren't affected by it (Pavel)"
* tag 'io_uring-5.11-2021-01-01' of git://git.kernel.dk/linux-block:
kernel/io_uring: cancel io_uring before task works
io_uring: fix io_sqe_files_unregister() hangs
io_uring: add a helper for setting a ref node
io_uring: don't assume mm is constant across submits
Linus Torvalds [Mon, 28 Dec 2020 19:40:22 +0000 (11:40 -0800)]
depmod: handle the case of /sbin/depmod without /sbin in PATH
Commit
436e980e2ed5 ("kbuild: don't hardcode depmod path") stopped
hard-coding the path of depmod, but in the process caused trouble for
distributions that had that /sbin location, but didn't have it in the
PATH (generally because /sbin is limited to the super-user path).
Work around it for now by just adding /sbin to the end of PATH in the
depmod.sh script.
Reported-and-tested-by: Sedat Dilek <sedat.dilek@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pavel Begunkov [Wed, 30 Dec 2020 21:34:16 +0000 (21:34 +0000)]
kernel/io_uring: cancel io_uring before task works
For cancelling io_uring requests it needs either to be able to run
currently enqueued task_works or having it shut down by that moment.
Otherwise io_uring_cancel_files() may be waiting for requests that won't
ever complete.
Go with the first way and do cancellations before setting PF_EXITING and
so before putting the task_work infrastructure into a transition state
where task_work_run() would better not be called.
Cc: stable@vger.kernel.org # 5.5+
Signed-off-by: Pavel Begunkov <asml.silence@gmail.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Pavel Begunkov [Wed, 30 Dec 2020 21:34:15 +0000 (21:34 +0000)]
io_uring: fix io_sqe_files_unregister() hangs
io_sqe_files_unregister() uninterruptibly waits for enqueued ref nodes,
however requests keeping them may never complete, e.g. because of some
userspace dependency. Make sure it's interruptible otherwise it would
hang forever.
Cc: stable@vger.kernel.org # 5.6+
Signed-off-by: Pavel Begunkov <asml.silence@gmail.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Pavel Begunkov [Wed, 30 Dec 2020 21:34:14 +0000 (21:34 +0000)]
io_uring: add a helper for setting a ref node
Setting a new reference node to a file data is not trivial, don't repeat
it, add and use a helper.
Cc: stable@vger.kernel.org # 5.6+
Signed-off-by: Pavel Begunkov <asml.silence@gmail.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Linus Torvalds [Wed, 30 Dec 2020 20:02:12 +0000 (12:02 -0800)]
Merge tag 'ceph-for-5.11-rc2' of git://github.com/ceph/ceph-client
Pull ceph fixes from Ilya Dryomov:
"A fix for an edge case in MClientRequest encoding and a couple of
trivial fixups for the new msgr2 support"
* tag 'ceph-for-5.11-rc2' of git://github.com/ceph/ceph-client:
libceph: add __maybe_unused to DEFINE_MSGR2_FEATURE
libceph: align session_key and con_secret to 16 bytes
libceph: fix auth_signature buffer allocation in secure mode
ceph: reencode gid_list when reconnecting
Artem Bityutskiy [Sun, 27 Dec 2020 10:11:16 +0000 (12:11 +0200)]
intel_idle: add SnowRidge C-state table
Add C-state table for the SnowRidge SoC which is found on Intel Jacobsville
platforms.
The following has been changed.
1. C1E latency changed from 10us to 15us. It was measured using the
open source "wult" tool (the "nic" method, 15us is the 99.99th
percentile).
2. C1E power break even changed from 20us to 25us, which may result
in less C1E residency in some workloads.
3. C6 latency changed from 50us to 130us. Measured the same way as C1E.
The C6 C-state is supported only by some SnowRidge revisions, so add a C-state
table commentary about this.
On SnowRidge, C6 support is enumerated via the usual mechanism: "mwait" leaf of
the "cpuid" instruction. The 'intel_idle' driver does check this leaf, so even
though C6 is present in the table, the driver will only use it if the CPU does
support it.
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Rafael J. Wysocki [Tue, 29 Dec 2020 17:08:18 +0000 (18:08 +0100)]
cpufreq: intel_pstate: Fix fast-switch fallback path
When sugov_update_single_perf() falls back to the "frequency"
path due to the missing scale-invariance, it will call
cpufreq_driver_fast_switch() via sugov_fast_switch()
and the driver's ->fast_switch() callback will be invoked,
so it must not be NULL.
However, after commit
a365ab6b9dfb ("cpufreq: intel_pstate: Implement
the ->adjust_perf() callback") intel_pstate sets ->fast_switch() to
NULL when it is going to use intel_cpufreq_adjust_perf(), which is a
mistake, because on x86 the scale-invariance may be turned off
dynamically, so modify it to retain the original ->adjust_perf()
callback pointer.
Fixes: a365ab6b9dfb ("cpufreq: intel_pstate: Implement the ->adjust_perf() callback")
Reported-by: Kenneth R. Crudup <kenny@panix.com>
Tested-by: Kenneth R. Crudup <kenny@panix.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Rafael J. Wysocki [Wed, 30 Dec 2020 17:19:34 +0000 (18:19 +0100)]
Merge branch 'opp/linux-next' of git://git./linux/kernel/git/vireshk/pm
Pull operating performance points (OPP) framework fixes for 5.11-rc2
from Viresh Kumar:
"This contains two patches to fix freeing of resources in error paths."
* 'opp/linux-next' of git://git.kernel.org/pub/scm/linux/kernel/git/vireshk/pm:
opp: Call the missing clk_put() on error
opp: fix memory leak in _allocate_opp_table
Heiko Carstens [Mon, 28 Dec 2020 08:51:57 +0000 (09:51 +0100)]
s390/Kconfig: sort config S390 select list once again
...and add comments at the top and bottom.
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Heiko Carstens [Wed, 18 Nov 2020 20:23:33 +0000 (21:23 +0100)]
s390: update defconfigs
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Andres Freund [Mon, 28 Dec 2020 19:27:18 +0000 (11:27 -0800)]
block: add debugfs stanza for QUEUE_FLAG_NOWAIT
This was missed in
021a24460dc2. Leads to the numeric value of
QUEUE_FLAG_NOWAIT (i.e. 29) showing up in
/sys/kernel/debug/block/*/state.
Fixes: 021a24460dc28e7412aecfae89f60e1847e685c0
Cc: Konstantin Khlebnikov <khlebnikov@yandex-team.ru>
Cc: Mike Snitzer <snitzer@redhat.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Andres Freund <andres@anarazel.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Randy Dunlap [Tue, 29 Dec 2020 03:47:06 +0000 (19:47 -0800)]
fs: block_dev.c: fix kernel-doc warnings from struct block_device changes
Fix new kernel-doc warnings in fs/block_dev.c:
../fs/block_dev.c:1066: warning: Excess function parameter 'whole' description in 'bd_abort_claiming'
../fs/block_dev.c:1837: warning: Function parameter or member 'dev' not described in 'lookup_bdev'
Fixes: 4e7b5671c6a8 ("block: remove i_bdev")
Fixes: 37c3fc9abb25 ("block: simplify the block device claiming interface")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Christoph Hellwig <hch@lst.de>
Cc: linux-fsdevel@vger.kernel.org
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
projects / linux.git / log