Merge tag 'samsung-pinctrl-6.8' of https://git./linux/kernel/git/pinctrl/samsung into devel

Samsung pinctrl drivers changes for v6.8

1. New hardware: Add pin controllers for Samsung ExynosAutov920 and
   Google Tensor GS101.

2. Few DT bindings cleanups: add specific compatibles for each device
   using generic compatible as fallback.  This affects only DTS, no
   driver changes are needed.

3. Allow setting affinity on non wake-up external GPIO interrupts.

Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Merge tag 'renesas-pinctrl-for-v6.8-tag2' of git://git./linux/kernel/git/geert/renesas-drivers into devel

pinctrl: renesas: Updates for v6.8 (take two)

  - Add pinmux groups, power source, and input/output enable support for
    Ethernet pins on RZ/G2L SoCs,
  - Miscellaneous fixes and improvements.

Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

pinctrl: renesas: rzg2l: Add input enable to the Ethernet pins

Some of the RZ/G3S Ethernet pins (P1_0, P7_0) can be configured with
input enable.  Enable this functionality for these pins.

Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20231207070700.4156557-8-claudiu.beznea.uj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>

pinctrl: renesas: rzg2l: Add output enable support

Some of the Ethernet pins on RZ/G3S (but also valid for RZ/G2L) need to
have the direction of the IO buffer set as output for Ethernet to work
properly.  On RZ/G3S, these pins are P1_0/P7_0, P1_1/P7_1, and can have
the following Ethernet functions: TXC/TX_CLK or TX_CTL/TX_EN.

As the pins supporting output enable are SoC specific, and there is a
limited number of these pins (TXC/TX_CLK and/or TX_CTL/TX_EN), specify
output enable capable port limits in the platform-based configuration
data structure, to ensure proper validation.

The OEN support has been intantiated for RZ/G3S at the moment.

Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20231207070700.4156557-7-claudiu.beznea.uj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>

pinctrl: renesas: rzg2l: Add support to select power source for Ethernet pins

The GPIO controller available on RZ/G3S (but also on RZ/G2L) supports
setting the power source for Ethernet pins.  Based on the interface b/w
the Ethernet controller and the Ethernet PHY, and on board design, a
specific power source needs to be selected.  The GPIO controller
supports 1.8V, 2.5V, and 3.3V power source selection for the Ethernet
pins.  This can be selected though the ETHx_POC registers (x={0, 1}).

Adjust the driver to support this, and to do proper instantiation for
the RZ/G3S and RZ/G2L SoCs.  On RZ/G2L only the get operation has been
tested at the moment.

While at it, as the power registers on RZ/G2L support access sizes of 8
bits, and these registers on RZ/G3S support access sizes of 8/16/32
bits, replace writel()/readl() on these registers with writeb()/readb().
This should allow us to use the same code on both SoCs w/o any issues.

Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20231207070700.4156557-6-claudiu.beznea.uj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>

pinctrl: renesas: rzg2l: Add pin configuration support for pinmux groups

On RZ/G3S different Ethernet pins need to be configured with different
settings (e.g. power-source needs to be set, RGMII TXC and TX_CTL pins
need output-enable).  Adjust the driver to allow specifying pin
configuration for pinmux groups.  With this, DT settings like the
following are taken into account by the driver:

    eth0_pins: eth0 {
    tx_ctl {
    pinmux = <RZG2L_PORT_PINMUX(1, 1, 1)>;  /* ET0_TX_CTL */
    power-source = <1800>;
    output-enable;
    drive-strength-microamp = <5200>;
    };
    };

Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20231207070700.4156557-5-claudiu.beznea.uj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>

pinctrl: renesas: rzg2l: Move arg and index in the main function block

Move arg and index in the main block of the function as they are used by
more than one case block of switch-case (3 out of 4 for arg, 2 out of 4
for index). In this way some lines of code are removed.

Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20231207070700.4156557-4-claudiu.beznea.uj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>

pinctrl: samsung: add exynosautov920 pinctrl

Add pinctrl data for ExynosAutov920 SoC.
It has a newly applied pinctrl register layer for ExynosAuto series.

Pinctrl data for ExynosAutoV920 SoC.
 - GPA0,GPA1 (10): External wake up interrupt
 - GPQ0 (2): SPMI (PMIC I/F)
 - GPB0,GPB1,GPB2,GPB3,GPB4,GPB5,GPB6 (47): I2S Audio
 - GPH0,GPH1,GPH2,GPH3,GPH4,GPH5,GPH6,GPH8 (49): PCIE, UFS, Ethernet
 - GPG0,GPG1,GPG2,GPG3,GPG4,GPG5 (29): General purpose
 - GPP0,GPP1,GPP2,GPP3,GPP4,GPP5,GPP6,GPP7,GPP8,GPP9,GPP10 (77): USI

Signed-off-by: Jaewon Kim <jaewon02.kim@samsung.com>
Link: https://lore.kernel.org/r/20231211114145.106255-3-jaewon02.kim@samsung.com
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>

pinctrl: samsung: support ExynosAuto GPIO structure

New ExynosAuto series GPIO have a different register structure.
In the existing Exynos series, EINT control register is enumerated after
a specific offset (e.g EXYNOS_GPIO_ECON_OFFSET, EXYNOS_GPIO_EMASK_OFFSET).
However, from ExynosAutov920 SoC, the register that controls EINT belongs
to each GPIO bank, and each GPIO bank has 0x1000 align.

This is a structure to protect the GPIO bank using S2MPU in VM environment,
and will only be applied in ExynosAuto series SoCs.

--------------------------------------------------------------
| Original Exynos            | ExynosAuto                    |
|------------------------------------------------------------|
| 0x0   GPIO_CON             | 0x0   GPIO_CON                |
| 0x4   GPIO_DAT             | 0x4   GPIO_DAT                |
| 0x8   GPIO_PUD             | 0x8   GPIO_PUD                |
| 0xc   GPIO_DRV             | 0xc   GPIO_DRV                |
| 0x10  GPIO_CONPDN          | 0x10  GPIO_CONPDN             |
| 0x14  GPIO_PUDPDN          | 0x14  GPIO_PUDPDN             |
|----------------------------| 0x18  EINT_CON (per_bank)     |
| ...                        | 0x1c  EINT_FLTCON0 (per_bank) |
| ...                        | 0x20  EINT_FLTCON1 (per_bank) |
| ...                        | 0x24  EINT_MASK (per_bank)    |
| ...                        | 0x28  EINT_PEND (per_bank)    |
|----------------------------|-------------------------------|
| 0x700 EINT_CON (global)    | ...                           |
| 0x800 EINT_FLTCON (global) | ...                           |
| 0x900 EINT_MASK (global)   | ...                           |
| 0xa00 EINT_FEND (global)   | ...                           |
--------------------------------------------------------------

Signed-off-by: Jaewon Kim <jaewon02.kim@samsung.com>
Link: https://lore.kernel.org/r/20231211114145.106255-2-jaewon02.kim@samsung.com
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>

Merge tag 'pef2256-framer' into devel

Immutable tag for the PEF2256 framer

MAINTAINERS: Add the Lantiq PEF2256 driver entry

After contributing the driver, add myself as the maintainer for the
Lantiq PEF2256 driver.

Signed-off-by: Herve Codina <herve.codina@bootlin.com>
Reviewed-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Link: https://lore.kernel.org/r/20231128132534.258459-6-herve.codina@bootlin.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

pinctrl: Add support for the Lantic PEF2256 pinmux

The Lantiq PEF2256 is a framer and line interface component designed to
fulfill all required interfacing between an analog E1/T1/J1 line and the
digital PCM system highway/H.100 bus.

This kind of component can be found in old telecommunication system.
It was used to digital transmission of many simultaneous telephone calls
by time-division multiplexing. Also using HDLC protocol, WAN networks
can be reached through the framer.

This pinmux support handles the pin muxing part (pins RP(A..D) and pins
XP(A..D)) of the PEF2256.

Signed-off-by: Herve Codina <herve.codina@bootlin.com>
Reviewed-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20231128132534.258459-5-herve.codina@bootlin.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

net: wan: framer: Add support for the Lantiq PEF2256 framer

The Lantiq PEF2256 is a framer and line interface component designed to
fulfill all required interfacing between an analog E1/T1/J1 line and the
digital PCM system highway/H.100 bus.

Signed-off-by: Herve Codina <herve.codina@bootlin.com>
Reviewed-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Jakub Kicinski <kuba@kernel.org>
Link: https://lore.kernel.org/r/20231128132534.258459-4-herve.codina@bootlin.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

dt-bindings: net: Add the Lantiq PEF2256 E1/T1/J1 framer

The Lantiq PEF2256 is a framer and line interface component designed to
fulfill all required interfacing between an analog E1/T1/J1 line and the
digital PCM system highway/H.100 bus.

Signed-off-by: Herve Codina <herve.codina@bootlin.com>
Reviewed-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20231128132534.258459-3-herve.codina@bootlin.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

net: wan: Add framer framework support

A framer is a component in charge of an E1/T1 line interface.
Connected usually to a TDM bus, it converts TDM frames to/from E1/T1
frames. It also provides information related to the E1/T1 line.

The framer framework provides a set of APIs for the framer drivers
(framer provider) to create/destroy a framer and APIs for the framer
users (framer consumer) to obtain a reference to the framer, and
use the framer.

This basic implementation provides a framer abstraction for:
 - power on/off the framer
 - get the framer status (line state)
 - be notified on framer status changes
 - get/set the framer configuration

Signed-off-by: Herve Codina <herve.codina@bootlin.com>
Reviewed-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Acked-by: Jakub Kicinski <kuba@kernel.org>
Link: https://lore.kernel.org/r/20231128132534.258459-2-herve.codina@bootlin.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

pinctrl: samsung: Add gs101 SoC pinctrl configuration

Add support for the pin-controller found on the gs101 SoC used in
Pixel 6 phones.

Reviewed-by: Sam Protsenko <semen.protsenko@linaro.org>
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20231211162331.435900-10-peter.griffin@linaro.org
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>

pinctrl: core: Remove unused members from struct group_desc

All drivers are converted to use embedded struct pingroup.
Remove unused members from struct group_desc.

Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20231211190321.307330-14-andriy.shevchenko@linux.intel.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

pinctrl: starfive: Convert to use grp member

Convert drivers to use grp member embedded in struct group_desc,
because other members will be removed to avoid duplication and
desynchronisation of the generic pin group description.

Reviewed-by: Emil Renner Berthing <emil.renner.berthing@canonical.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20231211190321.307330-13-andriy.shevchenko@linux.intel.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

pinctrl: renesas: Convert to use grp member

Convert drivers to use grp member embedded in struct group_desc,
because other members will be removed to avoid duplication and
desynchronisation of the generic pin group description.

Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20231211190321.307330-12-andriy.shevchenko@linux.intel.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

pinctrl: mediatek: Convert to use grp member

Convert drivers to use grp member embedded in struct group_desc,
because other members will be removed to avoid duplication and
desynchronisation of the generic pin group description.

Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20231211190321.307330-11-andriy.shevchenko@linux.intel.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

pinctrl: keembay: Convert to use grp member

Convert drivers to use grp member embedded in struct group_desc,
because other members will be removed to avoid duplication and
desynchronisation of the generic pin group description.

Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20231211190321.307330-10-andriy.shevchenko@linux.intel.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

pinctrl: ingenic: Convert to use grp member

Convert drivers to use grp member embedded in struct group_desc,
because other members will be removed to avoid duplication and
desynchronisation of the generic pin group description.

Acked-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20231211190321.307330-9-andriy.shevchenko@linux.intel.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

pinctrl: imx: Convert to use grp member

Convert drivers to use grp member embedded in struct group_desc,
because other members will be removed to avoid duplication and
desynchronisation of the generic pin group description.

Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20231211190321.307330-8-andriy.shevchenko@linux.intel.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

pinctrl: equilibrium: Convert to use grp member

Convert drivers to use grp member embedded in struct group_desc,
because other members will be removed to avoid duplication and
desynchronisation of the generic pin group description.

Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20231211190321.307330-7-andriy.shevchenko@linux.intel.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

pinctrl: bcm: Convert to use grp member

Convert drivers to use grp member embedded in struct group_desc,
because other members will be removed to avoid duplication and
desynchronisation of the generic pin group description.

Tested-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20231211190321.307330-6-andriy.shevchenko@linux.intel.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

pinctrl: core: Embed struct pingroup into struct group_desc

struct group_desc is a particular version of the struct pingroup
with associated opaque data. Start switching pin control core and
drivers to use it explicitly.

Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20231211190321.307330-5-andriy.shevchenko@linux.intel.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

pinctrl: ingenic: Use C99 initializers in PINCTRL_PIN_GROUP()

For the better flexibility use C99 initializers in PINCTRL_PIN_GROUP().

Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20231211190321.307330-4-andriy.shevchenko@linux.intel.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

pinctrl: mediatek: Use C99 initializers in PINCTRL_PIN_GROUP()

For the better flexibility use C99 initializers in PINCTRL_PIN_GROUP().

Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20231211190321.307330-3-andriy.shevchenko@linux.intel.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

pinctrl: core: Add a convenient define PINCTRL_GROUP_DESC()

Add PINCTRL_GROUP_DESC() macro for inline use.

Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20231211190321.307330-2-andriy.shevchenko@linux.intel.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Merge tag 'gpio-remove-gpiochip_is_requested-for-v6.8-rc1' of git://git./linux/kernel/git/brgl/linux into devel

gpio: remove gpiochip_is_requested()

- provide a safer alternative to gpiochip_is_requested()
- convert all existing users
- remove gpiochip_is_requested()

dt-bindings: pinctrl: samsung: correct ExynosAutov920 wake-up compatibles

ExynosAutov920 SoC wake-up pin controller has different register layout
than Exynos7, thus it should not be marked as compatible.  Neither DTS
nor Linux driver was merged yet, so the change does not impact ABI.

Cc: Jaewon Kim <jaewon02.kim@samsung.com>
Fixes: 904140fa4553 ("dt-bindings: pinctrl: samsung: use Exynos7 fallbacks for newer wake-up controllers")
Link: https://lore.kernel.org/r/20231210133915.42112-1-krzysztof.kozlowski@linaro.org
Reviewed-by: Jaewon Kim <jaewon02.kim@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>

dt-bindings: pinctrl: samsung: add gs101-wakeup-eint compatible

gs101 is similar to newer Exynos SoCs like Exynos850 and ExynosAutov9
where more than one pin controller can do external wake-up interrupt.
So add a dedicated compatible for it.

Reviewed-by: Sam Protsenko <semen.protsenko@linaro.org>
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Link: https://lore.kernel.org/r/20231209233106.147416-8-peter.griffin@linaro.org
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>

dt-bindings: pinctrl: samsung: add google,gs101-pinctrl compatible

Add the "google,gs101-pinctrl" compatible to the dt-schema bindings
documentation.

Reviewed-by: Sam Protsenko <semen.protsenko@linaro.org>
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Link: https://lore.kernel.org/r/20231209233106.147416-7-peter.griffin@linaro.org
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>

gpiolib: remove gpiochip_is_requested()

We have no external users of gpiochip_is_requested(). Let's remove it
and replace its internal calls with direct testing of the REQUESTED flag.

Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>

gpiolib: use gpiochip_dup_line_label() in for_each helpers

Rework for_each_requested_gpio_in_range() to use the new helper to
retrieve a dynamically allocated copy of the descriptor label and free
it at the end of each iteration. We need to leverage the CLASS()'
destructor to make sure that the label is freed even when breaking out
of the loop.

Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>

pinctrl: sppctl: use gpiochip_dup_line_label()

Use the new gpiochip_dup_line_label() helper to safely retrieve the
descriptor label.

Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>

pinctrl: baytrail: use gpiochip_dup_line_label()

Use the new gpiochip_dup_line_label() helper to safely retrieve the
descriptor label.

Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>

pinctrl: nomadik: use gpiochip_dup_line_label()

Use the new gpiochip_dup_line_label() helper to safely retrieve the
descriptor label.

Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>

pinctrl: abx500: use gpiochip_dup_line_label()

Use the new gpiochip_dup_line_label() helper to safely retrieve the
descriptor label.

Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>

gpio: stmpe: use gpiochip_dup_line_label()

Use the new gpiochip_dup_line_label() helper to safely retrieve the
descriptor label.

Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>

gpio: wm8994: use gpiochip_dup_line_label()

Use the new gpiochip_dup_line_label() helper to safely retrieve the
descriptor label.

Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>

gpio: wm831x: use gpiochip_dup_line_label()

Use the new gpiochip_dup_line_label() helper to safely retrieve the
descriptor label.

Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>

gpiolib: provide gpiochip_dup_line_label()

gpiochip_is_requested() not only has a misleading name but it returns
a pointer to a string that is freed when the descriptor is released.

Provide a new helper meant to replace it, which returns a copy of the
label string instead.

Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>

pinctrl: nuvoton: Convert to use struct pingroup and PINCTRL_PINGROUP()

The pin control header provides struct pingroup and PINCTRL_PINGROUP() macro.
Utilize them instead of open coded variants in the driver.

Reviewed-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20231204160033.1872569-6-andriy.shevchenko@linux.intel.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

pinctrl: keembay: Convert to use struct pingroup

The pin control header provides struct pingroup.
Utilize it instead of open coded variants in the driver.

Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20231204160033.1872569-5-andriy.shevchenko@linux.intel.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

pinctrl: equilibrium: Convert to use struct pingroup

The pin control header provides struct pingroup.
Utilize it instead of open coded variants in the driver.

Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20231204160033.1872569-4-andriy.shevchenko@linux.intel.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

pinctrl: core: Make pins const unsigned int pointer in struct group_desc

It's unclear why it's not a const unsigned int pointer from day 1.
Make the pins member const unsigned int pointer in struct group_desc.
Update necessary APIs.

Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20231204160033.1872569-3-andriy.shevchenko@linux.intel.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

pinctrl: renesas: Mark local variable with const in ->set_mux()

We are not going to change pins in the ->set_mux() callback. Mark
the local variable with a const qualifier. While at it, make it
also unsigned.

Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20231204160033.1872569-2-andriy.shevchenko@linux.intel.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

dt-bindings: pinctrl: qcom,sm8550-lpass-lpi: add X1E80100 LPASS LPI

Document the Qualcomm X1E80100 SoC Low Power Audio SubSystem Low Power
Island (LPASS LPI) pin controller, compatible with earlier SM8550 model.

Cc: Abel Vesa <abel.vesa@linaro.org>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Reviewed-by: Abel Vesa <abel.vesa@linaro.org>
Link: https://lore.kernel.org/r/20231129155738.167030-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

pinctrl: pinctrl-single: add ti,j7200-padconf compatible

On j7200, during suspend to ram pinctrl contexts are lost. To save and
restore contexts during suspend/resume, the flag PCS_CONTEXT_LOSS_OFF
shall be set.

Signed-off-by: Thomas Richard <thomas.richard@bootlin.com>
Reviewed-by: Tony Lindgren <tony@atomide.com>
Link: https://lore.kernel.org/r/20231128-j7200-pinctrl-s2r-v1-2-704e7dc24460@bootlin.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

dt-bindings: pinctrl: pinctrl-single: add ti,j7200-padconf compatible

Add the "ti,j7200-padconf" compatible to support suspend to ram on
j7200.

Signed-off-by: Thomas Richard <thomas.richard@bootlin.com>
Reviewed-by: Tony Lindgren <tony@atomide.com>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://lore.kernel.org/r/20231128-j7200-pinctrl-s2r-v1-1-704e7dc24460@bootlin.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

pinctrl: qcom: fail to retrieve configuration from invalid pin groups

The pinconf-groups debugfs file dumps each valid configuration item of
all pin groups. Some platforms and devices may have pin groups which
cannot be accessed, according to commit 691bf5d5a7bf ("pinctrl: qcom:
Don't allow protected pins to be requested"). Fail for each
configuration item of an invalid pin group by checking the GPIO chip's
valid mask.

The validity of the pin group cannot be checked in the generic pinconf
dump (function "pinconf_generic_dump_one"), as it does not directly
interact with the gpiochip or the pinmux callbacks (which would give it
access to the request callback). Instead, an entry contains the ID and
name of the pingroup with no properties when all items fail.

Signed-off-by: Richard Acayan <mailingradian@gmail.com>
Link: https://lore.kernel.org/r/20231128020202.728156-3-mailingradian@gmail.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

pinctrl: mediatek: Switch to use no-IRQ PM helpers

Since pm.h provides a helper for system no-IRQ PM callbacks,
switch the driver to use it instead of open coded variant.

Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20231122144744.2222207-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

pinctrl: Convert unsigned to unsigned int

Simple type conversion with no functional change implied.
While at it, adjust indentation where it makes sense.

Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20231129161459.1002323-24-andriy.shevchenko@linux.intel.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

pinctrl: imx: Use temporary variable to hold pins

The pins are allocated from the heap, but in order to pass
them as constant object, we need to use non-constant pointer.
Achieve this by using a temporary variable.

Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20231129161459.1002323-6-andriy.shevchenko@linux.intel.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

pinctrl: equilibrium: Use temporary variable to hold pins

The pins are allocated from the heap, but in order to pass
them as constant object, we need to use non-constant pointer.
Achieve this by using a temporary variable.

Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20231129161459.1002323-5-andriy.shevchenko@linux.intel.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

pinctrl: equilibrium: Unshadow error code of of_property_count_u32_elems()

of_property_count_u32_elems() might return an error code in some cases.
It's naturally better to assign what it's returned to the err variable
and supply the real code to the upper layer(s). Besides that, it's a
common practice to avoid assignments for the data in cases when we know
that the error condition happened. Refactor the code accordingly.

Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20231129161459.1002323-4-andriy.shevchenko@linux.intel.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

pinctrl: qcom: lpass-lpi: Remove unused member in struct lpi_pingroup

The group is not used anywhere, remove it. And if needed, it should be
struct pingroup anyway.

Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20231129161459.1002323-3-andriy.shevchenko@linux.intel.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

pinctrl: qcom: lpass-lpi: Replace kernel.h with what is being used

Replace kernel.h with what exactly is being used, i.e. array_size.h.

Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20231129161459.1002323-2-andriy.shevchenko@linux.intel.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Merge tag 'renesas-pinctrl-for-v6.8-tag1' of git://git./linux/kernel/git/geert/renesas-drivers into devel

pinctrl: renesas: Updates for v6.8

  - Add support for interrupt affinity to the RZ/G2L GPIO driver,
  - Drop unneeded quotes in the RZ/A2 Pin controller DT bindings.

Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

pinctrl: samsung: add irq_set_affinity() for non wake up external gpio interrupt

To support affinity setting for non wake up external gpio interrupt, add
irq_set_affinity callback using irq number from pinctrl driver data.

Before this patch, changing the irq affinity of gpio interrupt is not
possible:

    # cat /proc/irq/418/smp_affinity
    3ff
    # echo 00f > /proc/irq/418/smp_affinity
    # cat /proc/irq/418/smp_affinity
    3ff
    # cat /proc/interrupts
               CPU0       CPU1       CPU2       CPU3    ...
    418:       3631          0          0          0    ...

With this patch applied, it's possible to change irq affinity of gpio
interrupt:

    # cat /proc/irq/418/smp_affinity
    3ff
    # echo 00f > /proc/irq/418/smp_affinity
    # cat /proc/irq/418/smp_affinity
    00f
    # cat /proc/interrupts
               CPU0       CPU1       CPU2       CPU3      ...
    418:       3893        201        181        188      ...

Signed-off-by: Youngmin Nam <youngmin.nam@samsung.com>
Reviewed-by: Sam Protsenko <semen.protsenko@linaro.org>
Tested-by: Sam Protsenko <semen.protsenko@linaro.org>
Link: https://lore.kernel.org/r/20231126094618.2545116-1-youngmin.nam@samsung.com
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>

dt-bindings: pinctrl: renesas: Drop unneeded quotes

Drop unneeded quotes over simple string values to fix a soon to be
enabled yamllint warning:

  [error] string value is redundantly quoted with any quotes (quoted-strings)

Signed-off-by: Rob Herring <robh@kernel.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20231122224409.2808999-1-robh@kernel.org
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>

pinctrl: renesas: rzg2l: Enhance driver to support interrupt affinity setting

Implement irq_set_affinity callback so that we can set affinity
for GPIO IRQs.

Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20231011195923.67404-1-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>

pinctrl: don't include GPIOLIB private header

gpio_to_desc() is declared in linux/gpio.h so there's no need to include
gpiolib.h directly.

Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20231115165001.2932350-4-brgl@bgdev.pl
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

pinctrl: stop using gpiod_to_chip()

Don't dereference struct gpio_chip directly, use dedicated gpio_device
getters instead.

Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20231115165001.2932350-3-brgl@bgdev.pl
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Merge tag 'gpio-device-get-label-for-v6.8-rc1' of git://git./linux/kernel/git/brgl/linux into devel

gpiolib: provide gpio_device_get_label()

Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

gpiolib: provide gpio_device_get_label()

Provide a getter for the GPIO device label string so that users don't
have to dereference struct gpio_chip directly.

Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>

pinctrl: as3722: Use devm_gpiochip_add_data() to simplify remove path

Use devm version of gpiochip add function to handle removal for us.

Signed-off-by: Andrew Davis <afd@ti.com>
Reviewed-by: Andy Shevchenko <andy@kernel.org>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20231116223045.274211-1-afd@ti.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

pinctrl: qcom: Add X1E80100 pinctrl driver

Add initial pinctrl driver to support pin configuration with pinctrl
framework for X1E80100 SoC.

Co-developed-by: Abel Vesa <abel.vesa@linaro.org>
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
Signed-off-by: Rajendra Nayak <quic_rjendra@quicinc.com>
Co-developed-by: Sibi Sankar <quic_sibis@quicinc.com>
Signed-off-by: Sibi Sankar <quic_sibis@quicinc.com>
Reviewed-by: Bjorn Andersson <andersson@kernel.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20231117093921.31968-3-quic_sibis@quicinc.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

dt-bindings: pinctrl: qcom: Add X1E80100 pinctrl

Add device tree binding Documentation details for Qualcomm X1E80100 TLMM
device.

Signed-off-by: Rajendra Nayak <quic_rjendra@quicinc.com>
Co-developed-by: Sibi Sankar <quic_sibis@quicinc.com>
Signed-off-by: Sibi Sankar <quic_sibis@quicinc.com>
Reviewed-by: Bjorn Andersson <andersson@kernel.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20231117093921.31968-2-quic_sibis@quicinc.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

pinctrl: npcm7xx: prevent glitch when setting the GPIO to output high

Enable GPIO output after setting the output value to prevent a glitch
when pinctrl driver sets gpio pin to output high and the pin is in
the default state (high->low->high).

Signed-off-by: Tomer Maimon <tmaimon77@gmail.com>
Signed-off-by: William A. Kennington III <william@wkennington.com>
Link: https://lore.kernel.org/r/20231115211209.1683449-1-william@wkennington.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

pinctrl: stm32: return errors from stm32_gpio_direction_output()

In the STMicroelectronics STM32 driver, stm32_gpio_direction_output()
ignores the result of pinctrl_gpio_direction_output() for no good reason.
Let's propagate errors from pinctrl_gpio_direction_output() upstream...

Found by Linux Verification Center (linuxtesting.org) with the Svace static
analysis tool.

Signed-off-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Link: https://lore.kernel.org/r/5ce023a8-db0c-13a9-be42-09e3348ca44d@omp.ru
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

dt-bindings: pinctrl: samsung: use Exynos7 fallbacks for newer wake-up controllers

Older ARM8 SoCs like Exynos5433, Exynos7 and Exynos7885 have the pin
controller with wake-up interrupts muxed, thus the wake-up interrupt
controller device node has interrupts property, while its pin banks
might not (because they are muxed by the wake-up controller).

Newer SoCs like Exynos850 and ExynosAutov9 do not used muxed wake-up
interrupts:
1. Wake-up interrupt controller device node has no interrupts,
2. Its pin banks have interrupts (since there is no muxing).

Their programming interface is however still compatible with Exynos7,
thus change the bindings to express this: retain compatibility with
Exynos7 and add new compatibility fallback of Exynos850 in newer
designs.

No driver changes are needed.  This is necessary only to properly
describe DTS.

Acked-by: Conor Dooley <conor.dooley@microchip.com>
Acked-by: Jaewon Kim <jaewon02.kim@samsung.com>
Link: https://lore.kernel.org/r/20231122200407.423264-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>

MAINTAINERS: Remove snawrocki's git tree

There is already krzk/linux.git listed, which is currently used.

Signed-off-by: Petr Vorel <pvorel@suse.cz>
Acked-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Link: https://lore.kernel.org/r/20231108085630.7767-1-pvorel@suse.cz
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>

dt-bindings: pinctrl: samsung: add exynosautov920

Add compatible string for exynosautov920 pin controller.

Signed-off-by: Jaewon Kim <jaewon02.kim@samsung.com>
Link: https://lore.kernel.org/r/20231115095609.39883-7-jaewon02.kim@samsung.com
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>

dt-bindings: pinctrl: samsung: add specific compatibles for existing SoC

Samsung Exynos SoC reuses several devices from older designs, thus
historically we kept the old (block's) compatible only.  This works fine
and there is no bug here, however guidelines expressed in
Documentation/devicetree/bindings/writing-bindings.rst state that:
1. Compatibles should be specific.
2. We should add new compatibles in case of bugs or features.

Add compatibles specific to each SoC in front of all old-SoC-like
compatibles.

Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20231108104343.24192-6-krzysztof.kozlowski@linaro.org
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>

pinctrl: tps6594: Add driver for TPS6594 pinctrl and GPIOs

TI TPS6594 PMIC has 11 GPIOs which can be used
for different functions.

This patch adds a pinctrl and GPIO drivers in
order to use those functions.

Signed-off-by: Esteban Blanc <eblanc@baylibre.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20231108104124.2818275-1-eblanc@baylibre.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

pinctrl: qcom: lpass-lpi: allow slew rate bit in main pin config register

Existing Qualcomm SoCs have the LPASS pin controller slew rate control
in separate register, however this will change with upcoming Qualcomm
SoCs.  The slew rate will be part of the main register for pin
configuration, thus second device IO address space is not needed.

Prepare for supporting new SoCs by adding flag customizing the driver
behavior for slew rate.

Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20231013145935.220945-3-krzysztof.kozlowski@linaro.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

pinctrl: qcom: lpass-lpi: split slew rate set to separate function

Setting slew rate for each pin will grow with upcoming Qualcomm SoCs,
so split the code responsible for this into separate function for easier
readability and maintenance.

Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20231013145935.220945-2-krzysztof.kozlowski@linaro.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

pinctrl: qcom: Introduce the SM8650 Top Level Mode Multiplexer driver

Add Top Level Mode Multiplexer (pinctrl) support for the SM8650 platform.

Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20231106-topic-sm8650-upstream-tlmm-v3-3-0e179c368933@linaro.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

pinctrl: qcom: handle intr_target_reg wakeup_present/enable bits

New platforms uses a new set of bits to control the wakeirq
delivery to the PDC block.

The intr_wakeup_present_bit indicates if the GPIO supports
wakeirq and intr_wakeup_enable_bit enables wakeirq delivery
to the PDC block.

While the name seems to imply this only enables wakeup events,
it is required to allow interrupts events to the PDC block.

Enable this bit in the irq resource request/free if:
- gpio is in wakeirq map
- has the intr_wakeup_present_bit
- the intr_wakeup_enable_bit is set

Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20231106-topic-sm8650-upstream-tlmm-v3-2-0e179c368933@linaro.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

dt-bindings: pinctrl: document the SM8650 Top Level Mode Multiplexer

Document the Top Level Mode Multiplexer on the SM8650 Platform.

Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20231106-topic-sm8650-upstream-tlmm-v3-1-0e179c368933@linaro.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

pinctrl: qcom: sm8650-lpass-lpi: add SM8650 LPASS

Add driver for the pin controller in Low Power Audio SubSystem (LPASS)
of Qualcomm SM8650 SoC.

Notable differences against SM8550 LPASS pin controller:
1. Additional address space for slew rate thus driver uses
   LPI_FLAG_SLEW_RATE_SAME_REG and sets slew rate via different
   register.

2. Two new pin mux functions: qca_swr_clk and qca_swr_data

Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20231027093615.140656-3-krzysztof.kozlowski@linaro.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

dt-bindings: pinctrl: qcom,sm8650-lpass-lpi-pinctrl: add SM8650 LPASS

Add bindings for the pin controller in Low Power Audio SubSystem (LPASS)
of Qualcomm SM8650 SoC.

Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20231027093615.140656-2-krzysztof.kozlowski@linaro.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

pinctrl: tegra: Display pin function in pinconf-groups

The function that a pin is muxed to can be read from the top-level
pinctrl-maps debugfs file. However, this only reflects the values that
were specified in device tree, so they will only show deviations from
the hardware default setting. Display the current pinmux setting in the
per-controller pinconf-groups debugfs file along with the rest of the
per-pin configuration settings.

Signed-off-by: Thierry Reding <treding@nvidia.com>
Tested-by: Luca Ceresoli <luca.ceresoli@bootlin.com>
Link: https://lore.kernel.org/r/20230929122101.466266-1-thierry.reding@gmail.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Linux 6.7-rc1

wifi: iwlwifi: fix system commands group ordering

The commands should be sorted inside the group definition.
Fix the ordering so we won't get following warning:
WARN_ON(iwl_cmd_groups_verify_sorted(trans_cfg))

Link: https://lore.kernel.org/regressions/2fa930bb-54dd-4942-a88d-05a47c8e9731@gmail.com/
Link: https://lore.kernel.org/linux-wireless/CAHk-=wix6kqQ5vHZXjOPpZBfM7mMm9bBZxi2Jh7XnaKCqVf94w@mail.gmail.com/
Fixes: b6e3d1ba4fcf ("wifi: iwlwifi: mvm: implement new firmware API for statistics")
Tested-by: Niklāvs Koļesņikovs <pinkflames.linux@gmail.com>
Tested-by: Damian Tometzki <damian@riscv-rocks.de>
Acked-by: Kalle Valo <kvalo@kernel.org>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Merge tag 'parisc-for-6.7-rc1-2' of git://git./linux/kernel/git/deller/parisc-linux

Pull parisc architecture fixes from Helge Deller:

 - Include the upper 5 address bits when inserting TLB entries on a
   64-bit kernel.

   On physical machines those are ignored, but in qemu it's nice to have
   them included and to be correct.

 - Stop the 64-bit kernel and show a warning if someone tries to boot on
   a machine with a 32-bit CPU

 - Fix a "no previous prototype" warning in parport-gsc

* tag 'parisc-for-6.7-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux:
  parisc: Prevent booting 64-bit kernels on PA1.x machines
  parport: gsc: mark init function static
  parisc/pgtable: Do not drop upper 5 address bits of physical address

Merge tag 'loongarch-6.7' of git://git./linux/kernel/git/chenhuacai/linux-loongson

Pull LoongArch updates from Huacai Chen:

 - support PREEMPT_DYNAMIC with static keys

 - relax memory ordering for atomic operations

 - support BPF CPU v4 instructions for LoongArch

 - some build and runtime warning fixes

* tag 'loongarch-6.7' of git://git.kernel.org/pub/scm/linux/kernel/git/chenhuacai/linux-loongson:
  selftests/bpf: Enable cpu v4 tests for LoongArch
  LoongArch: BPF: Support signed mod instructions
  LoongArch: BPF: Support signed div instructions
  LoongArch: BPF: Support 32-bit offset jmp instructions
  LoongArch: BPF: Support unconditional bswap instructions
  LoongArch: BPF: Support sign-extension mov instructions
  LoongArch: BPF: Support sign-extension load instructions
  LoongArch: Add more instruction opcodes and emit_* helpers
  LoongArch/smp: Call rcutree_report_cpu_starting() earlier
  LoongArch: Relax memory ordering for atomic operations
  LoongArch: Mark __percpu functions as always inline
  LoongArch: Disable module from accessing external data directly
  LoongArch: Support PREEMPT_DYNAMIC with static keys

Merge tag 'powerpc-6.7-2' of git://git./linux/kernel/git/powerpc/linux

Pull powerpc fixes from Michael Ellerman:

 - Finish a refactor of pgprot_framebuffer() which dependend
   on some changes that were merged via the drm tree

 - Fix some kernel-doc warnings to quieten the bots

Thanks to Nathan Lynch and Thomas Zimmermann.

* tag 'powerpc-6.7-2' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
  powerpc/rtas: Fix ppc_rtas_rmo_buf_show() kernel-doc
  powerpc/pseries/rtas-work-area: Fix rtas_work_area_reserve_arena() kernel-doc
  powerpc/fb: Call internal __phys_mem_access_prot() in fbdev code
  powerpc: Remove file parameter from phys_mem_access_prot()
  powerpc/machdep: Remove trailing whitespaces

Merge tag '6.7-rc-smb3-client-fixes-part2' of git://git.samba.org/sfrench/cifs-2.6

Pull smb client fixes from Steve French:

 - ctime caching fix (for setxattr)

 - encryption fix

 - DNS resolver mount fix

 - debugging improvements

 - multichannel fixes including cases where server stops or starts
   supporting multichannel after mount

 - reconnect fix

 - minor cleanups

* tag '6.7-rc-smb3-client-fixes-part2' of git://git.samba.org/sfrench/cifs-2.6:
  cifs: update internal module version number for cifs.ko
  cifs: handle when server stops supporting multichannel
  cifs: handle when server starts supporting multichannel
  Missing field not being returned in ioctl CIFS_IOC_GET_MNT_INFO
  smb3: allow dumping session and tcon id to improve stats analysis and debugging
  smb: client: fix mount when dns_resolver key is not available
  smb3: fix caching of ctime on setxattr
  smb3: minor cleanup of session handling code
  cifs: reconnect work should have reference on server struct
  cifs: do not pass cifs_sb when trying to add channels
  cifs: account for primary channel in the interface list
  cifs: distribute channels across interfaces based on speed
  cifs: handle cases where a channel is closed
  smb3: more minor cleanups for session handling routines
  smb3: minor RDMA cleanup
  cifs: Fix encryption of cleared, but unset rq_iter data buffers

Merge tag 'probes-fixes-v6.7-rc1' of git://git./linux/kernel/git/trace/linux-trace

Pull probes fixes from Masami Hiramatsu:

 - Documentation update: Add a note about argument and return value
   fetching is the best effort because it depends on the type.

 - objpool: Fix to make internal global variables static in
   test_objpool.c.

 - kprobes: Unify kprobes_exceptions_nofify() prototypes. There are the
   same prototypes in asm/kprobes.h for some architectures, but some of
   them are missing the prototype and it causes a warning. So move the
   prototype into linux/kprobes.h.

 - tracing: Fix to check the tracepoint event and return event at
   parsing stage. The tracepoint event doesn't support %return but if
   $retval exists, it will be converted to %return silently. This finds
   that case and rejects it.

 - tracing: Fix the order of the descriptions about the parameters of
   __kprobe_event_gen_cmd_start() to be consistent with the argument
   list of the function.

* tag 'probes-fixes-v6.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/trace/linux-trace:
  tracing/kprobes: Fix the order of argument descriptions
  tracing: fprobe-event: Fix to check tracepoint event and return
  kprobes: unify kprobes_exceptions_nofify() prototypes
  lib: test_objpool: make global variables static
  Documentation: tracing: Add a note about argument and retval access

Merge tag 'fbdev-for-6.7-rc1' of git://git./linux/kernel/git/deller/linux-fbdev

Pull fbdev fixes and cleanups from Helge Deller:

 - fix double free and resource leaks in imsttfb

 - lots of remove callback cleanups and section mismatch fixes in
   omapfb, amifb and atmel_lcdfb

 - error code fix and memparse simplification in omapfb

* tag 'fbdev-for-6.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/linux-fbdev: (31 commits)
  fbdev: fsl-diu-fb: mark wr_reg_wa() static
  fbdev: amifb: Convert to platform remove callback returning void
  fbdev: amifb: Mark driver struct with __refdata to prevent section mismatch warning
  fbdev: hyperv_fb: fix uninitialized local variable use
  fbdev: omapfb/tpd12s015: Convert to platform remove callback returning void
  fbdev: omapfb/tfp410: Convert to platform remove callback returning void
  fbdev: omapfb/sharp-ls037v7dw01: Convert to platform remove callback returning void
  fbdev: omapfb/opa362: Convert to platform remove callback returning void
  fbdev: omapfb/hdmi: Convert to platform remove callback returning void
  fbdev: omapfb/dvi: Convert to platform remove callback returning void
  fbdev: omapfb/dsi-cm: Convert to platform remove callback returning void
  fbdev: omapfb/dpi: Convert to platform remove callback returning void
  fbdev: omapfb/analog-tv: Convert to platform remove callback returning void
  fbdev: atmel_lcdfb: Convert to platform remove callback returning void
  fbdev: omapfb/tpd12s015: Don't put .remove() in .exit.text and drop suppress_bind_attrs
  fbdev: omapfb/tfp410: Don't put .remove() in .exit.text and drop suppress_bind_attrs
  fbdev: omapfb/sharp-ls037v7dw01: Don't put .remove() in .exit.text and drop suppress_bind_attrs
  fbdev: omapfb/opa362: Don't put .remove() in .exit.text and drop suppress_bind_attrs
  fbdev: omapfb/hdmi: Don't put .remove() in .exit.text and drop suppress_bind_attrs
  fbdev: omapfb/dvi: Don't put .remove() in .exit.text and drop suppress_bind_attrs
  ...

tracing/kprobes: Fix the order of argument descriptions

The order of descriptions should be consistent with the argument list of
the function, so "kretprobe" should be the second one.

int __kprobe_event_gen_cmd_start(struct dynevent_cmd *cmd, bool kretprobe,
                                 const char *name, const char *loc, ...)

Link: https://lore.kernel.org/all/20231031041305.3363712-1-yujie.liu@intel.com/
Fixes: 2a588dd1d5d6 ("tracing: Add kprobe event command generation functions")
Suggested-by: Mukesh Ojha <quic_mojha@quicinc.com>
Signed-off-by: Yujie Liu <yujie.liu@intel.com>
Reviewed-by: Mukesh Ojha <quic_mojha@quicinc.com>
Signed-off-by: Masami Hiramatsu (Google) <mhiramat@kernel.org>

Merge tag 'drm-next-2023-11-10' of git://anongit.freedesktop.org/drm/drm

Pull drm fixes from Daniel Vetter:
 "Dave's VPN to the big machine died, so it's on me to do fixes pr this
  and next week while everyone else is at plumbers.

   - big pile of amd fixes, but mostly for hw support newly added in 6.7

   - i915 fixes, mostly minor things

   - qxl memory leak fix

   - vc4 uaf fix in mock helpers

   - syncobj fix for DRM_SYNCOBJ_WAIT_FLAGS_WAIT_AVAILABLE"

* tag 'drm-next-2023-11-10' of git://anongit.freedesktop.org/drm/drm: (78 commits)
  drm/amdgpu: fix error handling in amdgpu_vm_init
  drm/amdgpu: Fix possible null pointer dereference
  drm/amdgpu: move UVD and VCE sched entity init after sched init
  drm/amdgpu: move kfd_resume before the ip late init
  drm/amd: Explicitly check for GFXOFF to be enabled for s0ix
  drm/amdgpu: Change WREG32_RLC to WREG32_SOC15_RLC where inst != 0 (v2)
  drm/amdgpu: Use correct KIQ MEC engine for gfx9.4.3 (v5)
  drm/amdgpu: add smu v13.0.6 pcs xgmi ras error query support
  drm/amdgpu: fix software pci_unplug on some chips
  drm/amd/display: remove duplicated argument
  drm/amdgpu: correct mca debugfs dump reg list
  drm/amdgpu: correct acclerator check architecutre dump
  drm/amdgpu: add pcs xgmi v6.4.0 ras support
  drm/amdgpu: Change extended-scope MTYPE on GC 9.4.3
  drm/amdgpu: disable smu v13.0.6 mca debug mode by default
  drm/amdgpu: Support multiple error query modes
  drm/amdgpu: refine smu v13.0.6 mca dump driver
  drm/amdgpu: Do not program PF-only regs in hdp_v4_0.c under SRIOV (v2)
  drm/amdgpu: Skip PCTL0_MMHUB_DEEPSLEEP_IB write in jpegv4.0.3 under SRIOV
  drm: amd: Resolve Sphinx unexpected indentation warning
  ...

Merge tag 'arm64-fixes' of git://git./linux/kernel/git/arm64/linux

Pull arm64 fixes from Catalin Marinas:
 "Mostly PMU fixes and a reworking of the pseudo-NMI disabling on broken
  MediaTek firmware:

   - Move the MediaTek GIC quirk handling from irqchip to core. Before
     the merging window commit 44bd78dd2b88 ("irqchip/gic-v3: Disable
     pseudo NMIs on MediaTek devices w/ firmware issues") temporarily
     addressed this issue. Fixed now at a deeper level in the arch code

   - Reject events meant for other PMUs in the CoreSight PMU driver,
     otherwise some of the core PMU events would disappear

   - Fix the Armv8 PMUv3 driver driver to not truncate 64-bit registers,
     causing some events to be invisible

   - Remove duplicate declaration of __arm64_sys##name following the
     patch to avoid prototype warning for syscalls

   - Typos in the elf_hwcap documentation"

* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
  arm64/syscall: Remove duplicate declaration
  Revert "arm64: smp: avoid NMI IPIs with broken MediaTek FW"
  arm64: Move MediaTek GIC quirk handling from irqchip to core
  arm64/arm: arm_pmuv3: perf: Don't truncate 64-bit registers
  perf: arm_cspmu: Reject events meant for other PMUs
  Documentation/arm64: Fix typos in elf_hwcaps

Merge tag 'sound-fix-6.7-rc1' of git://git./linux/kernel/git/tiwai/sound

Pull sound fixes from Takashi Iwai:
 "A collection of fixes for rc1.

  The majority of changes are various ASoC driver-specific small fixes
  and usual HD-audio quirks, while there are a couple of core changes: a
  fix in ALSA core procfs code to avoid deadlocks at disconnection and
  an ASoC core fix for DAPM clock widgets"

* tag 'sound-fix-6.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
  OSS: dmasound/paula: Convert to platform remove callback returning void
  ALSA: hda: ASUS UM5302LA: Added quirks for cs35L41/10431A83 on i2c bus
  ALSA: info: Fix potential deadlock at disconnection
  ASoC: nau8540: Add self recovery to improve capture quility
  ALSA: hda/realtek: Add support dual speaker for Dell
  ALSA: hda: Add ASRock X670E Taichi to denylist
  ALSA: hda/realtek: Add quirk for ASUS UX7602ZM
  ASoC: SOF: sof-client: trivial: fix comment typo
  ASoC: dapm: fix clock get name
  ASoC: hdmi-codec: register hpd callback on component probe
  ASoC: mediatek: mt8186_mt6366_rt1019_rt5682s: trivial: fix error messages
  ASoC: da7219: Improve system suspend and resume handling
  ASoC: codecs: Modify macro value error
  ASoC: codecs: Modify the wrong judgment of re value
  ASoC: codecs: Modify the maximum value of calib
  ASoC: amd: acp: fix for i2s mode register field update
  ASoC: codecs: aw88399: Fix -Wuninitialized in aw_dev_set_vcalb()
  ASoC: rt712-sdca: fix speaker route missing issue
  ASoC: rockchip: Fix unused rockchip_i2s_tdm_match warning for !CONFIG_OF
  ASoC: ti: omap-mcbsp: Fix runtime PM underflow warnings

Merge tag 'amd-drm-next-6.7-2023-11-10' of https://gitlab.freedesktop.org/agd5f/linux into drm-next

amd-drm-next-6.7-2023-11-10:

amdgpu:
- SR-IOV fixes
- DMCUB fixes
- DCN3.5 fixes
- DP2 fixes
- SubVP fixes
- SMU14 fixes
- SDMA4.x fixes
- Suspend/resume fixes
- AGP regression fix
- UAF fixes for some error cases
- SMU 13.0.6 fixes
- Documentation fixes
- RAS fixes
- Hotplug fixes
- Scheduling entity ordering fix
- GPUVM fixes

Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
From: Alex Deucher <alexander.deucher@amd.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231110190703.4741-1-alexander.deucher@amd.com

Merge tag 'spi-fix-v6.7-merge-window' of git://git./linux/kernel/git/broonie/spi

Pull spi fixes from Mark Brown:
 "A couple of fixes that came in during the merge window: one Kconfig
  dependency fix and another fix for a long standing issue where a sync
  transfer races with system suspend"

* tag 'spi-fix-v6.7-merge-window' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi:
  spi: Fix null dereference on suspend
  spi: spi-zynq-qspi: add spi-mem to driver kconfig dependencies

Merge tag 'mmc-v6.7-2' of git://git./linux/kernel/git/ulfh/mmc

Pull MMC fixes from Ulf Hansson:
 "MMC core:
   - Fix broken cache-flush support for Micron eMMCs
   - Revert 'mmc: core: Capture correct oemid-bits for eMMC cards'

  MMC host:
   - sdhci_am654: Fix TAP value parsing for legacy speed mode
   - sdhci-pci-gli: Fix support for ASPM mode for GL9755/GL9750
   - vub300: Fix an error path in probe"

* tag 'mmc-v6.7-2' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc:
  mmc: sdhci-pci-gli: GL9750: Mask the replay timer timeout of AER
  mmc: sdhci-pci-gli: GL9755: Mask the replay timer timeout of AER
  Revert "mmc: core: Capture correct oemid-bits for eMMC cards"
  mmc: vub300: fix an error code
  mmc: Add quirk MMC_QUIRK_BROKEN_CACHE_FLUSH for Micron eMMC Q2J54A
  mmc: sdhci_am654: fix start loop index for TAP value parsing