The syzbot fuzzer and Gerald Lee have identified a use-after-free bug
in the gadgetfs driver, involving processes concurrently mounting and
unmounting the gadgetfs filesystem. In particular, gadgetfs_fill_super()
can race with gadgetfs_kill_sb(), causing the latter to deallocate
the_device while the former is using it. The output from KASAN says,
in part:
BUG: KASAN: use-after-free in instrument_atomic_read_write include/linux/instrumented.h:102 [inline]
BUG: KASAN: use-after-free in atomic_fetch_sub_release include/linux/atomic/atomic-instrumented.h:176 [inline]
BUG: KASAN: use-after-free in __refcount_sub_and_test include/linux/refcount.h:272 [inline]
BUG: KASAN: use-after-free in __refcount_dec_and_test include/linux/refcount.h:315 [inline]
BUG: KASAN: use-after-free in refcount_dec_and_test include/linux/refcount.h:333 [inline]
BUG: KASAN: use-after-free in put_dev drivers/usb/gadget/legacy/inode.c:159 [inline]
BUG: KASAN: use-after-free in gadgetfs_kill_sb+0x33/0x100 drivers/usb/gadget/legacy/inode.c:2086
Write of size 4 at addr ffff8880276d7840 by task syz-executor126/18689
syzkaller:~# modprobe speakup_audptr
input: Speakup as /devices/virtual/input/input4
initialized device: /dev/synth, node (MAJOR 10, MINOR 125)
speakup 3.1.6: initialized
synth name on entry is: (null)
synth probe
spk_ttyio_initialise_ldisc failed because tty_kopen_exclusive returned
failed (errno -16), then remove the module, we will get a null-ptr-defer
problem, as follow:
Driver's probe allocates memory for RX FIFO (port->rx_fifo) based on
default RX FIFO depth, e.g. 16. Later during serial startup the
qcom_geni_serial_port_setup() updates the RX FIFO depth
(port->rx_fifo_depth) to match real device capabilities, e.g. to 32.
The RX UART handle code will read "port->rx_fifo_depth" number of words
into "port->rx_fifo" buffer, thus exceeding the bounds. This can be
observed in certain configurations with Qualcomm Bluetooth HCI UART
device and KASAN:
Bluetooth: hci0: QCA Product ID :0x00000010
Bluetooth: hci0: QCA SOC Version :0x400a0200
Bluetooth: hci0: QCA ROM Version :0x00000200
Bluetooth: hci0: QCA Patch Version:0x00000d2b
Bluetooth: hci0: QCA controller version 0x02000200
Bluetooth: hci0: QCA Downloading qca/htbtfw20.tlv
bluetooth hci0: Direct firmware load for qca/htbtfw20.tlv failed with error -2
Bluetooth: hci0: QCA Failed to request file: qca/htbtfw20.tlv (-2)
Bluetooth: hci0: QCA Failed to download patch (-2)
==================================================================
BUG: KASAN: slab-out-of-bounds in handle_rx_uart+0xa8/0x18c
Write of size 4 at addr ffff279347d578c0 by task swapper/0/0
When changing the ebpf program put() routines to support being called
from within IRQ context the program ID was reset to zero prior to
calling the perf event and audit UNLOAD record generators, which
resulted in problems as the ebpf program ID was bogus (always zero).
This patch addresses this problem by removing an unnecessary call to
bpf_prog_free_id() in __bpf_prog_offload_destroy() and adjusting
__bpf_prog_put() to only call bpf_prog_free_id() after audit and perf
have finished their bpf program unload tasks in
bpf_prog_put_deferred(). For the record, no one can determine, or
remember, why it was necessary to free the program ID, and remove it
from the IDR, prior to executing bpf_prog_put_deferred();
regardless, both Stanislav and Alexei agree that the approach in this
patch should be safe.
It is worth noting that when moving the bpf_prog_free_id() call, the
do_idr_lock parameter was forced to true as the ebpf devs determined
this was the correct as the do_idr_lock should always be true. The
do_idr_lock parameter will be removed in a follow-up patch, but it
was kept here to keep the patch small in an effort to ease any stable
backports.
I also modified the bpf_audit_prog() logic used to associate the
AUDIT_BPF record with other associated records, e.g. @ctx != NULL.
Instead of keying off the operation, it now keys off the execution
context, e.g. '!in_irg && !irqs_disabled()', which is much more
appropriate and should help better connect the UNLOAD operations with
the associated audit state (other audit records).
Cc: stable@vger.kernel.org Fixes: d809e134be7a ("bpf: Prepare bpf_prog_put() to be called from irq context.") Reported-by: Burn Alting <burn.alting@iinet.net.au> Reported-by: Jiri Olsa <olsajiri@gmail.com> Suggested-by: Stanislav Fomichev <sdf@google.com> Suggested-by: Alexei Starovoitov <alexei.starovoitov@gmail.com> Signed-off-by: Paul Moore <paul@paul-moore.com> Acked-by: Stanislav Fomichev <sdf@google.com> Link: https://lore.kernel.org/r/20230106154400.74211-1-paul@paul-moore.com Signed-off-by: Alexei Starovoitov <ast@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The 32-bit memory resource is needed for non-prefetchable memory
allocations on the PCIe bus, however with some cards (such as the
SM768) the system fails to allocate memory from this.
Checking the allocation against the datasheet, it looks like there
has been a mis-calcualation of the resource for the first memory
region (0x0060090000..0x0070ffffff) which in the data-sheet for
the fu740 (v1p2) is from 0x0060000000..0x007fffffff. Changing
this to allocate from 0x0060090000..0x007fffffff fixes the probing
issues.
Fixes: ae80d5148085 ("riscv: dts: Add PCIe support for the SiFive FU740-C000 SoC") Cc: Paul Walmsley <paul.walmsley@sifive.com> Cc: Greentime Hu <greentime.hu@sifive.com> Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk> Cc: stable@vger.kernel.org Tested-by: Ron Economos <re@w6rz.net> # from IRC Reviewed-by: Conor Dooley <conor.dooley@microchip.com> Signed-off-by: Conor Dooley <conor.dooley@microchip.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We need to take minimum of both sides of the USB3 link into consideration,
not just the downstream port. Fix this by calling tb_usb3_max_link_rate()
instead.
On async reads, page data is allocated before sending. When the
response is received but it has no data to fill (e.g.
STATUS_END_OF_FILE), __calc_signature() will still include the pages in
its computation, leading to an invalid signature check.
This patch fixes this by not setting the async read smb_rqst page data
(zeroed by default) if its got_bytes is 0.
This can be reproduced/verified with xfstests generic/465.
Cc: <stable@vger.kernel.org> Signed-off-by: Enzo Matsumiya <ematsumiya@suse.de> Reviewed-by: Paulo Alcantara (SUSE) <pc@cjr.nz> Signed-off-by: Steve French <stfrench@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If we have one task trying to start the quota rescan worker while another
one is trying to disable quotas, we can end up hitting a race that results
in the quota rescan worker doing a NULL pointer dereference. The steps for
this are the following:
1) Quotas are enabled;
2) Task A calls the quota rescan ioctl and enters btrfs_qgroup_rescan().
It calls qgroup_rescan_init() which returns 0 (success) and then joins a
transaction and commits it;
3) Task B calls the quota disable ioctl and enters btrfs_quota_disable().
It clears the bit BTRFS_FS_QUOTA_ENABLED from fs_info->flags and calls
btrfs_qgroup_wait_for_completion(), which returns immediately since the
rescan worker is not yet running.
Then it starts a transaction and locks fs_info->qgroup_ioctl_lock;
4) Task A queues the rescan worker, by calling btrfs_queue_work();
5) The rescan worker starts, and calls rescan_should_stop() at the start
of its while loop, which results in 0 iterations of the loop, since
the flag BTRFS_FS_QUOTA_ENABLED was cleared from fs_info->flags by
task B at step 3);
6) Task B sets fs_info->quota_root to NULL;
7) The rescan worker tries to start a transaction and uses
fs_info->quota_root as the root argument for btrfs_start_transaction().
This results in a NULL pointer dereference down the call chain of
btrfs_start_transaction(). The stack trace is something like the one
reported in Link tag below:
When syncing the log, if we fail to write log tree extent buffers, we mark
the log for a full commit and abort the transaction. However we don't need
to abort the transaction, all we really need to do is to make sure no one
can commit a superblock pointing to new log tree roots. Just because we
got a failure writing extent buffers for a log tree, it does not mean we
will also fail to do a transaction commit.
One particular case is if due to a bug somewhere, when writing log tree
extent buffers, the tree checker detects some corruption and the writeout
fails because of that. Aborting the transaction can be very disruptive for
a user, specially if the issue happened on a root filesystem. One example
is the scenario in the Link tag below, where an isolated corruption on log
tree leaves was causing transaction aborts when syncing the log.
If the controller is suspended by runtime PM, the clock is already
disabled, so do not try to disable it again during removal. Use
pm_runtime_disable() to flush any pending runtime PM transitions.
The ACPI PRM address space handler calls efi_call_virt_pointer() to
execute PRM firmware code, but doing so is only permitted when the EFI
runtime environment is available. Otherwise, such calls are guaranteed
to result in a crash, and must therefore be avoided.
Given that the EFI runtime services may become unavailable after a crash
occurring in the firmware, we need to check this each time the PRM
address space handler is invoked. If the EFI runtime services were not
available at registration time to being with, don't install the address
space handler at all.
Fixes: cefc7ca46235 ("ACPI: PRM: implement OperationRegion handler for the PlatformRtMechanism subtype") Signed-off-by: Ard Biesheuvel <ardb@kernel.org> Cc: All applicable <stable@vger.kernel.org> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
(Actually, this is fixing the "Read the Current Status" command sent to
the device's outgoing mailbox, but it is only currently used for the PWM
instructions.)
The PCI-1760 is operated mostly by sending commands to a set of Outgoing
Mailbox registers, waiting for the command to complete, and reading the
result from the Incoming Mailbox registers. One of these commands is
the "Read the Current Status" command. The number of this command is
0x07 (see the User's Manual for the PCI-1760 at
<https://advdownload.advantech.com/productfile/Downloadfile2/1-11P6653/PCI-1760.pdf>.
The `PCI1760_CMD_GET_STATUS` macro defined in the driver should expand
to this command number 0x07, but unfortunately it currently expands to
0x03. (Command number 0x03 is not defined in the User's Manual.)
Correct the definition of the `PCI1760_CMD_GET_STATUS` macro to fix it.
This is used by all the PWM subdevice related instructions handled by
`pci1760_pwm_insn_config()` which are probably all broken. The effect
of sending the undefined command number 0x03 is not known.
Fixes: 14b93bb6bbf0 ("staging: comedi: adv_pci_dio: separate out PCI-1760 support") Cc: <stable@vger.kernel.org> # v4.5+ Signed-off-by: Ian Abbott <abbotti@mev.co.uk> Link: https://lore.kernel.org/r/20230103143754.17564-1-abbotti@mev.co.uk Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Texas Instruments TUSB8041 has an autosuspend problem at high
temperature.
If there is not USB traffic, after a couple of ms, the device enters in
autosuspend mode. In this condition the external clock stops working, to
save energy. When the USB activity turns on, ther hub exits the
autosuspend state, the clock starts running again and all works fine.
At ambient temperature all works correctly, but at high temperature,
when the USB activity turns on, the external clock doesn't restart and
the hub disappears from the USB bus.
Disabling the autosuspend mode for this hub solves the issue.
It is possible that in between calling fastrpc_map_get() until
map->fl->lock is taken in fastrpc_free_map(), another thread can call
fastrpc_map_lookup() and get a reference to a map that is about to be
deleted.
Rewrite fastrpc_map_get() to only increase the reference count of a map
if it's non-zero. Propagate this to callers so they can know if a map is
about to be deleted.
Fixes this warning:
refcount_t: addition on 0; use-after-free.
WARNING: CPU: 5 PID: 10100 at lib/refcount.c:25 refcount_warn_saturate
...
Call trace:
refcount_warn_saturate
[fastrpc_map_get inlined]
[fastrpc_map_lookup inlined]
fastrpc_map_create
fastrpc_internal_invoke
fastrpc_device_ioctl
__arm64_sys_ioctl
invoke_syscall
Fixes: c68cfb718c8f ("misc: fastrpc: Add support for context Invoke method") Cc: stable <stable@kernel.org> Signed-off-by: Ola Jeppsson <ola@snap.com> Signed-off-by: Abel Vesa <abel.vesa@linaro.org> Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org> Link: https://lore.kernel.org/r/20221124174941.418450-4-srinivas.kandagatla@linaro.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Do not remove the map from the list on error path in
fastrpc_init_create_process, instead call fastrpc_map_put, to avoid
use-after-free. Do not remove it on fastrpc_device_release either,
call fastrpc_map_put instead.
The fastrpc_free_map is the only proper place to remove the map.
This is called only after the reference count is 0.
Fixes: b49f6d83e290 ("misc: fastrpc: Fix a possible double free") Cc: stable <stable@kernel.org> Co-developed-by: Ola Jeppsson <ola@snap.com> Signed-off-by: Ola Jeppsson <ola@snap.com> Signed-off-by: Abel Vesa <abel.vesa@linaro.org> Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org> Link: https://lore.kernel.org/r/20221124174941.418450-3-srinivas.kandagatla@linaro.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
gcc-13 notices a type mismatch between function declaration
and definition for a few functions that have been converted
from returning vchiq specific status values to regular error
codes:
drivers/staging/vc04_services/interface/vchiq_arm/vchiq_arm.c:662:5: error: conflicting types for 'vchiq_initialise' due to enum/integer mismatch; have 'int(struct vchiq_instance **)' [-Werror=enum-int-mismatch]
drivers/staging/vc04_services/interface/vchiq_arm/vchiq_arm.c:1411:1: error: conflicting types for 'vchiq_use_internal' due to enum/integer mismatch; have 'int(struct vchiq_state *, struct vchiq_service *, enum USE_TYPE_E)' [-Werror=enum-int-mismatch]
drivers/staging/vc04_services/interface/vchiq_arm/vchiq_arm.c:1468:1: error: conflicting types for 'vchiq_release_internal' due to enum/integer mismatch; have 'int(struct vchiq_state *, struct vchiq_service *)' [-Werror=enum-int-mismatch]
Change the declarations to match the actual function definition.
The EM05CN modem has 2 USB configurations that are configurable via the AT
command AT+QCFG="usbnet",[ 0 | 2 ] which make the modem enumerate with
the following interfaces, respectively:
The EM05CN (SG) modem has 2 USB configurations that are configurable via the AT
command AT+QCFG="usbnet",[ 0 | 2 ] which make the modem enumerate with
the following interfaces, respectively:
The EM05-G (RS) modem has 2 USB configurations that are configurable via
the AT command AT+QCFG="usbnet",[ 0 | 2 ] which make the modem enumerate
with the following interfaces, respectively:
The EM05-G (CS) modem has 2 USB configurations that are configurable via
the AT command AT+QCFG="usbnet",[ 0 | 2 ] which make the modem enumerate
with the following interfaces, respectively:
The EM05-G (GR) modem has 2 USB configurations that are configurable via
the AT command AT+QCFG="usbnet",[ 0 | 2 ] which make the modem enumerate
with the following interfaces, respectively:
do_prlimit() adds the user-controlled resource value to a pointer that
will subsequently be dereferenced. In order to help prevent this
codepath from being used as a spectre "gadget" a barrier needs to be
added after checking the range.
Add a helper to evaluate ACPI usb device specific method (_DSM) provided
in case the USB3 port shouldn't enter U1 and U2 link states.
This _DSM was added as port specific retimer configuration may lead to
exit latencies growing beyond U1/U2 exit limits, and OS needs a way to
find which ports can't support U1/U2 link power management states.
One USB3 roothub port may support link power management, while another
root port on the same xHC can't due to different retimers used for
the ports.
This is the case with Intel Alder Lake, and possible future platforms
where retimers used for USB4 ports cause too long exit latecy to
enable native USB3 lpm U1 and U2 states.
Add a flag in the xhci port structure to indicate if the port is
lpm_incapable, and check it while calculating exit latency.
Allow PCI hosts to check and tune roothub and port settings
before the hub is up and running.
This override is needed to turn off U1 and U2 LPM for some ports
based on per port ACPI _DSM, _UPC, or possibly vendor specific mmio
values for Intel xHC hosts.
Usb core calls the host update_hub_device once it creates a hub.
Entering U1 or U2 link power save state on ports with this limitation
will cause link to fail, turning the usb device unusable in that setup.
Make sure xhci_free_dev() and xhci_kill_endpoint_urbs() do not race
and cause null pointer dereference when host suddenly dies.
Usb core may call xhci_free_dev() which frees the xhci->devs[slot_id]
virt device at the same time that xhci_kill_endpoint_urbs() tries to
loop through all the device's endpoints, checking if there are any
cancelled urbs left to give back.
hold the xhci spinlock while freeing the virt device
When the host controller is not responding, all URBs queued to all
endpoints need to be killed. This can cause a kernel panic if we
dereference an invalid endpoint.
Fix this by using xhci_get_virt_ep() helper to find the endpoint and
checking if the endpoint is valid before dereferencing it.
[233311.853271] xhci-hcd xhci-hcd.1.auto: xHCI host controller not responding, assume dead
[233311.853393] Unable to handle kernel NULL pointer dereference at virtual address 00000000000000e8
[233311.853964] pc : xhci_hc_died+0x10c/0x270
[233311.853971] lr : xhci_hc_died+0x1ac/0x270
We can't call these off the kiocb completion as that might be off
soft/hard irq context. Defer the calls to when we process the
task_work for this request. That avoids valid complaints like:
Update kiocb->ki_pos at execution time rather than in io_prep_rw().
io_prep_rw() happens before the job is enqueued to a worker and so the
offset might be read multiple times before being executed once.
Ensures that the file position in a set of _linked_ SQEs will be only
obtained after earlier SQEs have completed, and so will include their
incremented file position.
io_uring caches task references to avoid doing atomics for each of them
per request. If a request is put from the same task that allocated it,
then we can maintain a per-ctx cache of them. This obviously relies
on io_uring always pruning caches in a reliable way, and there's
currently a case off io_uring fd release where we can miss that.
One example is a ring setup with IOPOLL, which relies on the task
polling for completions, which will free them. However, if such a task
submits a request and then exits or closes the ring without reaping
the completion, then ring release will reap and put. If release happens
from that very same task, the completed request task refs will get
put back into the cache pool. This is problematic, as we're now beyond
the point of pruning caches.
Manually drop these caches after doing an IOPOLL reap. This releases
references from the current task, which is enough. If another task
happens to be doing the release, then the caching will not be
triggered and there's no issue.
Do not set REQ_F_NOWAIT if the socket is non blocking. When enabled this
causes the accept to immediately post a CQE with EAGAIN, which means you
cannot perform an accept SQE on a NONBLOCK socket asynchronously.
By removing the flag if there is no pending accept then poll is armed as
usual and when a connection comes in the CQE is posted.
We currently check REQ_F_POLLED before arming async poll for a
notification to retry. If it's set, then we don't allow poll and will
punt to io-wq instead. This is done to prevent a situation where a buggy
driver will repeatedly return that there's space/data available yet we
get -EAGAIN.
However, if we already transferred data, then it should be safe to rely
on poll again. Gate the check on whether or not REQ_F_PARTIAL_IO is
also set.
Like commit 7ba89d2af17a for recv/recvmsg, support MSG_WAITALL for the
send side. If this flag is set and we do a short send, retry for a
stream of seqpacket socket.
We currently don't attempt to get the full asked for length even if
MSG_WAITALL is set, if we get a partial receive. If we do see a partial
receive, then just note how many bytes we did and return -EAGAIN to
get it retried.
The iov is advanced appropriately for the vector based case, and we
manually bump the buffer and remainder for the non-vector case.
Pass in EPOLL_URING_WAKE when signaling eventfd or doing poll related
wakups, so that we can check for a circular event dependency between
eventfd and epoll. If this flag is set when our wakeup handlers are
called, then we know we have a dependency that needs to terminate
multishot requests.
eventfd and epoll are the only such possible dependencies.
This is identical to eventfd_signal(), but it allows the caller to pass
in a mask to be used for the poll wakeup key. The use case is avoiding
repeated multishot triggers if we have a dependency between eventfd and
io_uring.
If we setup an eventfd context and register that as the io_uring eventfd,
and at the same time queue a multishot poll request for the eventfd
context, then any CQE posted will repeatedly trigger the multishot request
until it terminates when the CQ ring overflows.
In preparation for io_uring detecting this circular dependency, add the
mentioned helper so that io_uring can pass in EPOLL_URING as part of the
poll wakeup key.
Cc: stable@vger.kernel.org # 6.0
[axboe: fold in !CONFIG_EVENTFD fix from Zhang Qilong] Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Sasha Levin <sashal@kernel.org>
We can have dependencies between epoll and io_uring. Consider an epoll
context, identified by the epfd file descriptor, and an io_uring file
descriptor identified by iofd. If we add iofd to the epfd context, and
arm a multishot poll request for epfd with iofd, then the multishot
poll request will repeatedly trigger and generate events until terminated
by CQ ring overflow. This isn't a desired behavior.
Add EPOLL_URING so that io_uring can pass it in as part of the poll wakeup
key, and io_uring can check for that to detect a potential recursive
invocation.
This isn't a reliable mechanism to tell if we have task_work pending, we
really should be looking at whether we have any items queued. This is
problematic if forward progress is gated on running said task_work. One
such example is reading from a pipe, where the write side has been closed
right before the read is started. The fput() of the file queues TWA_RESUME
task_work, and we need that task_work to be run before ->release() is
called for the pipe. If ->release() isn't called, then the read will sit
forever waiting on data that will never arise.
Fix this by io_run_task_work() so it checks if we have task_work pending
rather than rely on TIF_NOTIFY_SIGNAL for that. The latter obviously
doesn't work for task_work that is queued without TWA_SIGNAL.
PMD sharing can only be done in PUD_SIZE-aligned pieces of VMAs; however,
it is possible that HugeTLB VMAs are split without unsharing the PMDs
first.
Without this fix, it is possible to hit the uffd-wp-related WARN_ON_ONCE
in hugetlb_change_protection [1]. The key there is that
hugetlb_unshare_all_pmds will not attempt to unshare PMDs in
non-PUD_SIZE-aligned sections of the VMA.
It might seem ideal to unshare in hugetlb_vm_op_open, but we need to
unshare in both the new and old VMAs, so unsharing in hugetlb_vm_op_split
seems natural.
Link: https://lkml.kernel.org/r/20230104231910.1464197-1-jthoughton@google.com Fixes: 6dfeaff93be1 ("hugetlb/userfaultfd: unshare all pmds for hugetlbfs when register wp") Signed-off-by: James Houghton <jthoughton@google.com> Reviewed-by: Mike Kravetz <mike.kravetz@oracle.com> Acked-by: Peter Xu <peterx@redhat.com> Cc: Axel Rasmussen <axelrasmussen@google.com> Cc: Muchun Song <songmuchun@bytedance.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Removing the firmware framebuffer from the driver means that even
if the driver doesn't support the IP blocks in a GPU it will no
longer be functional after the driver fails to initialize.
This change will ensure that unsupported IP blocks at least cause
the driver to work with the EFI framebuffer.
Cc: stable@vger.kernel.org Suggested-by: Alex Deucher <alexander.deucher@amd.com> Reviewed-by: Alex Deucher <alexander.deucher@amd.com> Reviewed-by: Lijo Lazar <lijo.lazar@amd.com> Signed-off-by: Mario Limonciello <mario.limonciello@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Disable runtime power management on several sienna cichlid
cards, otherwise SMU will possibly fail to be resumed from
runtime suspend. Will drop this after a clean solution between
kernel driver and SMU FW is available.
amdgpu 0000:63:00.0: amdgpu: GECC is enabled
amdgpu 0000:63:00.0: amdgpu: SECUREDISPLAY: securedisplay ta ucode is not available
amdgpu 0000:63:00.0: amdgpu: SMU is resuming...
amdgpu 0000:63:00.0: amdgpu: SMU: I'm not done with your command: SMN_C2PMSG_66:0x0000000E SMN_C2PMSG_82:0x00000080
amdgpu 0000:63:00.0: amdgpu: Failed to SetDriverDramAddr!
amdgpu 0000:63:00.0: amdgpu: Failed to setup smc hw!
[drm:amdgpu_device_ip_resume_phase2 [amdgpu]] *ERROR* resume of IP block <smu> failed -62
amdgpu 0000:63:00.0: amdgpu: amdgpu_device_ip_resume failed (-62)
v2: seperate to a function.
Signed-off-by: Guchun Chen <guchun.chen@amd.com> Reviewed-by: Evan Quan <evan.quan@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Stable-dep-of: 1923bc5a56da ("drm/amd: Delay removal of the firmware framebuffer") Signed-off-by: Sasha Levin <sashal@kernel.org>
After [1][2], if we catch exceptions due to EFI runtime service, we will
clear EFI_RUNTIME_SERVICES bit to disable EFI runtime service, then the
subsequent routine which invoke the EFI runtime service should fail.
But the userspace cat efivars through /sys/firmware/efi/efivars/ will stuck
and infinite loop calling read() due to efivarfs_file_read() return -EINTR.
The -EINTR is converted from EFI_ABORTED by efi_status_to_err(), and is
an improper return value in this situation, so let virt_efi_xxx() return
EFI_DEVICE_ERROR and converted to -EIO to invoker.
If nilfs2 reads a corrupted disk image and tries to reads a b-tree node
block by calling __nilfs_btree_get_block() against an invalid virtual
block address, it returns -ENOENT because conversion of the virtual block
address to a disk block address fails. However, this return value is the
same as the internal code that b-tree lookup routines return to indicate
that the block being searched does not exist, so functions that operate on
that b-tree may misbehave.
When nilfs_btree_insert() receives this spurious 'not found' code from
nilfs_btree_do_lookup(), it misunderstands that the 'not found' check was
successful and continues the insert operation using incomplete lookup path
data, causing the following crash:
This patch fixes the root cause of this problem by replacing the error
code that __nilfs_btree_get_block() returns on block address conversion
failure from -ENOENT to another internal code -EINVAL which means that the
b-tree metadata is corrupted.
By returning -EINVAL, it propagates without glitches, and for all relevant
b-tree operations, functions in the upper bmap layer output an error
message indicating corrupted b-tree metadata via
nilfs_bmap_convert_error(), and code -EIO will be eventually returned as
it should be.
Using REQ_OP_ZONE_APPEND operations for synchronous writes to sequential
files succeeds regardless of the zone write pointer position, as long as
the target zone is not full. This means that if an external (buggy)
application writes to the zone of a sequential file underneath the file
system, subsequent file write() operation will succeed but the file size
will not be correct and the file will contain invalid data written by
another application.
Modify zonefs_file_dio_append() to check the written sector of an append
write (returned in bio->bi_iter.bi_sector) and return -EIO if there is a
mismatch with the file zone wp offset field. This change triggers a call
to zonefs_io_error() and a zone check. Modify zonefs_io_error_cb() to
not expose the unexpected data after the current inode size when the
errors=remount-ro mode is used. Other error modes are correctly handled
already.
Fixes: 02ef12a663c7 ("zonefs: use REQ_OP_ZONE_APPEND for sync DIO") Cc: stable@vger.kernel.org Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com> Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A sanity check was introduced considering maximum flowrings above
256 as insane and effectively aborting the device probe. This
resulted in regression for number of users as the value turns out
to be sane after all.
The driver shutdown callback (which sends EDL_SOC_RESET to the device
over serdev) should not be invoked when HCI device is not open (e.g. if
hci_dev_open_sync() failed), because the serdev and its TTY are not open
either. Also skip this step if device is powered off
(qca_power_shutdown()).
The shutdown callback causes use-after-free during system reboot with
Qualcomm Atheros Bluetooth:
Unable to handle kernel paging request at virtual address 0072662f67726fd7
...
CPU: 6 PID: 1 Comm: systemd-shutdow Tainted: G W 6.1.0-rt5-00325-g8a5f56bcfcca #8
Hardware name: Qualcomm Technologies, Inc. Robotics RB5 (DT)
Call trace:
tty_driver_flush_buffer+0x4/0x30
serdev_device_write_flush+0x24/0x34
qca_serdev_shutdown+0x80/0x130 [hci_uart]
device_shutdown+0x15c/0x260
kernel_restart+0x48/0xac
KASAN report:
BUG: KASAN: use-after-free in tty_driver_flush_buffer+0x1c/0x50
Read of size 8 at addr ffff16270c2e0018 by task systemd-shutdow/1
The dsi_irq_stats structure is a little too big to fit on the
stack of a 32-bit task, depending on the specific gcc options:
fbdev/omap2/omapfb/dss/dsi.c: In function 'dsi_dump_dsidev_irqs':
fbdev/omap2/omapfb/dss/dsi.c:1621:1: error: the frame size of 1064 bytes is larger than 1024 bytes [-Werror=frame-larger-than=]
Since this is only a debugfs file, performance is not critical,
so just dynamically allocate it, and print an error message
in there in place of a failure code when the allocation fails.
Currently we have a btrfs_debug() for run_one_delayed_ref() failure, but
if end users hit such problem, there will be no chance that
btrfs_debug() is enabled. This can lead to very little useful info for
debugging.
This patch will:
- Add extra info for error reporting
Including:
* logical bytenr
* num_bytes
* type
* action
* ref_mod
- Replace the btrfs_debug() with btrfs_err()
- Move the error reporting into run_one_delayed_ref()
This is to avoid use-after-free, the @node can be freed in the caller.
This error should only be triggered at most once.
As if run_one_delayed_ref() failed, we trigger the error message, then
causing the call chain to error out:
And we will abort the current transaction in btrfs_run_delayed_refs().
If we have to run delayed refs for the abort transaction,
run_one_delayed_ref() will just cleanup the refs and do nothing, thus no
new error messages would be output.
Since gcc13, each member of an enum has the same type as the enum [1]. And
that is inherited from its members. Provided these two:
SRP_TAG_NO_REQ = ~0U,
SRP_TAG_TSK_MGMT = 1U << 31
all other members are unsigned ints.
Esp. with SRP_MAX_SGE and SRP_TSK_MGMT_SQ_SIZE and their use in min(),
this results in the following warnings:
include/linux/minmax.h:20:35: error: comparison of distinct pointer types lacks a cast
drivers/infiniband/ulp/srp/ib_srp.c:563:42: note: in expansion of macro 'min'
include/linux/minmax.h:20:35: error: comparison of distinct pointer types lacks a cast
drivers/infiniband/ulp/srp/ib_srp.c:2369:27: note: in expansion of macro 'min'
So move the large values away to a separate enum, so that they don't
affect other members.
There is no functional change. Moving these two functions for following
patch "r8169: fix dmar pte write access is not set error".
Signed-off-by: Chunhao Lin <hau@realtek.com> Reviewed-by: Heiner Kallweit <hkallweit1@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
It's not very useful to copy back an empty ethtool_stats struct and
return 0 if we didn't actually have any stats. This also allows for
further simplification of this function in the future commits.
Signed-off-by: Daniil Tatianin <d-tatianin@yandex-team.ru> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Add a limit to 'config->vq_num' which is user controlled data which
comes from an vduse_ioctl to prevent large memory allocations.
Micheal says - This limit is somewhat arbitrary.
However, currently virtio pci and ccw are limited to a 16 bit vq number.
While MMIO isn't it is also isn't used with lots of VQs due to
current lack of support for per-vq interrupts.
Thus, the 0xffff limit on number of VQs corresponding
to a 16-bit VQ number seems sufficient for now.
This is found using static analysis with smatch.
Suggested-by: Michael S. Tsirkin <mst@redhat.com> Signed-off-by: Harshit Mogalapalli <harshit.m.mogalapalli@oracle.com>
Message-Id: <20221128155717.2579992-1-harshit.m.mogalapalli@oracle.com> Signed-off-by: Michael S. Tsirkin <mst@redhat.com> Acked-by: Jason Wang <jasowang@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Virtio_crypto use max_data_queues+1 to setup vqs,
we use vp_modern_get_num_queues to protect the vq range in setup_vq.
We could enter index >= vp_modern_get_num_queues(mdev) in setup_vq
if common->num_queues is not set well,and it return -ENOENT.
It is better to use -EINVAL instead.
Signed-off-by: Angus Chen <angus.chen@jaguarmicro.com>
Message-Id: <20221101111655.1947-1-angus.chen@jaguarmicro.com> Signed-off-by: Michael S. Tsirkin <mst@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The virtio_device vqs_list spinlocks must be initialized before use to
prevent functions that manipulate the device virtualqueues, such as
vring_new_virtqueue(), from blocking indefinitely.
Signed-off-by: Ricardo Cañuelo <ricardo.canuelo@collabora.com>
Message-Id: <20221012062949.1526176-1-ricardo.canuelo@collabora.com> Signed-off-by: Michael S. Tsirkin <mst@redhat.com> Reviewed-by: Xuan Zhuo <xuanzhuo@linux.alibaba.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Verify that nullness information is not porpagated in the branches
of register to register JEQ and JNE operations if one of them is
PTR_TO_BTF_ID. Implement this in C level so we can use CO-RE.
Signed-off-by: Hao Sun <sunhao.th@gmail.com> Suggested-by: Martin KaFai Lau <martin.lau@kernel.org> Link: https://lore.kernel.org/r/20221222024414.29539-2-sunhao.th@gmail.com Signed-off-by: Martin KaFai Lau <martin.lau@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
When there is a single DS no striping constraints need to be placed on
the IO. When such constraint is applied then buffered reads don't
coalesce to the DS's rsize.
Some laptops have been reported to wake up from s2idle when plugging
in the AC adapter or by closing the lid. This is a surprising
behavior that is further clarified by commit cb3e7d624c3ff ("PM:
wakeup: Add extra debugging statement for multiple active IRQs").
With that commit in place the following interaction can be seen
when the lid is closed:
[ 28.946038] PM: suspend-to-idle
[ 28.946083] ACPI: EC: ACPI EC GPE status set
[ 28.946101] ACPI: PM: Rearming ACPI SCI for wakeup
[ 28.950152] Timekeeping suspended for 3.320 seconds
[ 28.950152] PM: Triggering wakeup from IRQ 9
[ 28.950152] ACPI: EC: ACPI EC GPE status set
[ 28.950152] ACPI: EC: ACPI EC GPE dispatched
[ 28.995057] ACPI: EC: ACPI EC work flushed
[ 28.995075] ACPI: PM: Rearming ACPI SCI for wakeup
[ 28.995131] PM: Triggering wakeup from IRQ 9
[ 28.995271] ACPI: EC: ACPI EC GPE status set
[ 28.995291] ACPI: EC: ACPI EC GPE dispatched
[ 29.098556] ACPI: EC: ACPI EC work flushed
[ 29.207020] ACPI: EC: ACPI EC work flushed
[ 29.207037] ACPI: PM: Rearming ACPI SCI for wakeup
[ 29.211095] Timekeeping suspended for 0.739 seconds
[ 29.211095] PM: Triggering wakeup from IRQ 9
[ 29.211079] PM: Triggering wakeup from IRQ 7
[ 29.211095] ACPI: PM: ACPI non-EC GPE wakeup
[ 29.211095] PM: resume from suspend-to-idle
* IRQ9 on this laptop is used for the ACPI SCI.
* IRQ7 on this laptop is used for the GPIO controller.
What has occurred is when the lid was closed the EC woke up the
SoC from it's deepest sleep state and the kernel's s2idle loop
processed all EC events. When it was finished processing EC events,
it checked for any other reasons to wake (break the s2idle loop).
The IRQ for the GPIO controller was active so the loop broke, and
then this IRQ was processed. This is not a kernel bug but it is
certainly a surprising behavior, and to better debug it we should
have a dynamic debugging message that we can enact to catch it.
This patch results in some qemu test failures, specifically xilinx-zynq-a9
machine and zynq-zc702 as well as zynq-zed devicetree files, when trying
to boot from USB drive.
This can't happen right now, but in preparation for allowing
bio_split_to_limits() returning NULL if it ended the bio, check for it
in all the callers.
We have two types of task_work based creation, one is using an existing
worker to setup a new one (eg when going to sleep and we have no free
workers), and the other is allocating a new worker. Only the latter
should be freed when we cancel task_work creation for a new worker.
Fixes: af82425c6a2d ("io_uring/io-wq: free worker if task_work creation is canceled") Reported-by: syzbot+d56ec896af3637bdb7e4@syzkaller.appspotmail.com Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When scsi_dma_map() fails by returning a sges_left value less than zero,
the amount of logging produced can be extremely high. In a recent end-user
environment, 1200 messages per second were being sent to the log buffer.
This eventually overwhelmed the system and it stalled.
These error messages are not needed. Remove them.
Link: https://lore.kernel.org/r/20220303140203.12642-1-sreekanth.reddy@broadcom.com Suggested-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Cc: Paul Menzel <pmenzel@molgen.mpg.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The inline assembly for arm64's cmpxchg_double*() implementations use a
+Q constraint to hazard against other accesses to the memory location
being exchanged. However, the pointer passed to the constraint is a
pointer to unsigned long, and thus the hazard only applies to the first
8 bytes of the location.
GCC can take advantage of this, assuming that other portions of the
location are unchanged, leading to a number of potential problems.
This is similar to what we fixed back in commit:
fee960bed5e857eb ("arm64: xchg: hazard against entire exchange variable")
... but we forgot to adjust cmpxchg_double*() similarly at the same
time.
The same problem applies, as demonstrated with the following test:
Notice that at the lines with "BANG" comments, GCC has assumed that the
higher 8 bytes are unchanged by the cmpxchg_double() call, and that
`hi_old ^ hi_new` can be reduced to a constant zero, for both LSE and
LL/SC versions of cmpxchg_double().
This patch fixes the issue by passing a pointer to __uint128_t into the
+Q constraint, ensuring that the compiler hazards against the entire 16
bytes being modified.
With this change, GCC 12.1.0 compiles the above test as:
... sampling the high 8 bytes before and after the cmpxchg, and
performing an EOR, as we'd expect.
For backporting, I've tested this atop linux-4.9.y with GCC 5.5.0. Note
that linux-4.9.y is oldest currently supported stable release, and
mandates GCC 5.1+. Unfortunately I couldn't get a GCC 5.1 binary to run
on my machines due to library incompatibilities.
I've also used a standalone test to check that we can use a __uint128_t
pointer in a +Q constraint at least as far back as GCC 4.8.5 and LLVM
3.9.1.
When CONFIG_ARM64_LSE_ATOMICS=y, each use of an LL/SC atomic results in
a fragment of code being generated in a subsection without a clear
association with its caller. A trampoline in the caller branches to the
LL/SC atomic with with a direct branch, and the atomic directly branches
back into its trampoline.
This breaks backtracing, as any PC within the out-of-line fragment will
be symbolized as an offset from the nearest prior symbol (which may not
be the function using the atomic), and since the atomic returns with a
direct branch, the caller's PC may be missing from the backtrace.
For example, with secondary_start_kernel() hacked to contain
atomic_inc(NULL), the resulting exception can be reported as being taken
from cpus_are_stuck_in_kernel():
The rationale was to improve icache performance by grouping the LL/SC
atomics together. This has never been measured, and this theoretical
benefit is outweighed by other factors:
* As the subsections are collapsed into sections at object file
granularity, these are spread out throughout the kernel and can share
cachelines with unrelated code regardless.
* GCC 12.1.0 has been observed to place the trampoline out-of-line in
specialised __ll_sc_*() functions, introducing more branching than was
intended.
* Removing the trampolines has been observed to shrink a defconfig
kernel Image by 64KiB when building with GCC 12.1.0.
This patch removes the LL/SC trampolines, meaning that the LL/SC atomics
will be inlined into their callers (or placed in out-of line functions
using regular BL/RET pairs). When CONFIG_ARM64_LSE_ATOMICS=y, the LL/SC
atomics are always called in an unlikely branch, and will be placed in a
cold portion of the function, so this should have minimal impact to the
hot paths.
Other than the improved backtracing, there should be no functional
change as a result of this patch.
Signed-off-by: Mark Rutland <mark.rutland@arm.com> Cc: Will Deacon <will@kernel.org> Link: https://lore.kernel.org/r/20220817155914.3975112-2-mark.rutland@arm.com Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Stable-dep-of: 031af50045ea ("arm64: cmpxchg_double*: hazard against entire exchange variable") Signed-off-by: Sasha Levin <sashal@kernel.org>
This patch makes the indentation consistent and also aligns the trailing
backslashes. This makes the code easier to read for those (like myself)
who are easily distracted by these inconsistencies.
This is intended as a cleanup.
There should be no functional change as a result of this patch.
Signed-off-by: Mark Rutland <mark.rutland@arm.com> Cc: Boqun Feng <boqun.feng@gmail.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Will Deacon <will@kernel.org> Acked-by: Will Deacon <will@kernel.org> Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org> Link: https://lore.kernel.org/r/20211210151410.2782645-2-mark.rutland@arm.com Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Stable-dep-of: 031af50045ea ("arm64: cmpxchg_double*: hazard against entire exchange variable") Signed-off-by: Sasha Levin <sashal@kernel.org>
There is no real problem for normal IOPOLL as flush is also called with
uring_lock taken, but it's getting more complicated for IOPOLL|SQPOLL,
for which __io_cqring_overflow_flush() happens from the CQ waiting path.
Passing the host topology to the guest is almost certainly wrong
and will confuse the scheduler. In addition, several fields of
these CPUID leaves vary on each processor; it is simply impossible to
return the right values from KVM_GET_SUPPORTED_CPUID in such a way that
they can be passed to KVM_SET_CPUID2.
The values that will most likely prevent confusion are all zeroes.
Userspace will have to override it anyway if it wishes to present a
specific topology to the guest.
Cc: stable@vger.kernel.org Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
If CONFIG_DEFERRED_STRUCT_PAGE_INIT is enabled, memblock_free_pages()
only releases pages to the buddy allocator if they are not in the
deferred range. This is correct for free pages (as defined by
for_each_free_mem_pfn_range_in_zone()) because free pages in the
deferred range will be initialized and released as part of the deferred
init process. memblock_free_pages() is called by memblock_free_late(),
which is used to free reserved ranges after memblock_free_all() has
run. All pages in reserved ranges have been initialized at that point,
and accordingly, those pages are not touched by the deferred init
process. This means that currently, if the pages that
memblock_free_late() intends to release are in the deferred range, they
will never be released to the buddy allocator. They will forever be
reserved.
In addition, memblock_free_pages() calls kmsan_memblock_free_pages(),
which is also correct for free pages but is not correct for reserved
pages. KMSAN metadata for reserved pages is initialized by
kmsan_init_shadow(), which runs shortly before memblock_free_all().
For both of these reasons, memblock_free_pages() should only be called
for free pages, and memblock_free_late() should call __free_pages_core()
directly instead.
One case where this issue can occur in the wild is EFI boot on
x86_64. The x86 EFI code reserves all EFI boot services memory ranges
via memblock_reserve() and frees them later via memblock_free_late()
(efi_reserve_boot_services() and efi_free_boot_services(),
respectively). If any of those ranges happens to fall within the
deferred init range, the pages will not be released and that memory will
be unavailable.
For example, on an Amazon EC2 t3.micro VM (1 GB) booting via EFI:
Although rare, ssam_request_sync_init() can fail. In that case, the
request should be freed via ssam_request_sync_free(). Currently it is
leaked instead. Fix this.
Fixes: c167b9c7e3d6 ("platform/surface: Add Surface Aggregator subsystem") Signed-off-by: Maximilian Luz <luzmaximilian@gmail.com> Link: https://lore.kernel.org/r/20221220175608.1436273-1-luzmaximilian@gmail.com Reviewed-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
This patch fix the pulse per second output delta between
two synchronized end-points.
Based on Intel Discrete I225 Software User Manual Section
4.2.15 TimeSync Auxiliary Control Register, ST0[Bit 4] and
ST1[Bit 7] must be set to ensure that clock output will be
toggles based on frequency value defined. This is to ensure
that output of the PPS is aligned with the clock.
How to test:
1) Running time synchronization on both end points.
Ex: ptp4l --step_threshold=1 -m -f gPTP.cfg -i <interface name>
2) Configure PPS output using below command for both end-points
Ex: SDP0 on I225 REV4 SKU variant
3) Measure the output using analyzer for both end-points
Fixes: 87938851b6ef ("igc: enable auxiliary PHC functions for the i225") Signed-off-by: Christopher S Hall <christopher.s.hall@intel.com> Signed-off-by: Muhammad Husaini Zulkifli <muhammad.husaini.zulkifli@intel.com> Acked-by: Sasha Neftin <sasha.neftin@intel.com> Tested-by: Naama Meir <naamax.meir@linux.intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Including libbpf header files should be guarded by HAVE_LIBBPF_SUPPORT.
In bpf_counter.h, move the skeleton utilities under HAVE_BPF_SKEL.
Fixes: d6a735ef3277c45f ("perf bpf_counter: Move common functions to bpf_counter.h") Reported-by: Mike Leach <mike.leach@linaro.org> Signed-off-by: Ian Rogers <irogers@google.com> Tested-by: Arnaldo Carvalho de Melo <acme@redhat.com> Tested-by: Jiri Olsa <jolsa@kernel.org> Tested-by: Mike Leach <mike.leach@linaro.org> Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com> Cc: Mark Rutland <mark.rutland@arm.com> Cc: Namhyung Kim <namhyung@kernel.org> Cc: Peter Zijlstra <peterz@infradead.org> Link: http://lore.kernel.org/lkml/20230105172243.7238-1-mike.leach@linaro.org Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
.max_adj of ptp_clock_info acts as an absolute value for the amount in ppb
that can be set for a single call of .adjfine. This means that a single
call to .getfine cannot be greater than .max_adj or less than -(.max_adj).
Provides correct value for max frequency adjustment value supported by
devices.
The 'TCA_MPLS_LABEL' attribute is of 'NLA_U32' type, but has a
validation type of 'NLA_VALIDATE_FUNCTION'. This is an invalid
combination according to the comment above 'struct nla_policy':
"
Meaning of `validate' field, use via NLA_POLICY_VALIDATE_FN:
NLA_BINARY Validation function called for the attribute.
All other Unused - but note that it's a union
"
This can trigger the warning [1] in nla_get_range_unsigned() when
validation of the attribute fails. Despite being of 'NLA_U32' type, the
associated 'min'/'max' fields in the policy are negative as they are
aliased by the 'validate' field.
Fix by changing the attribute type to 'NLA_BINARY' which is consistent
with the above comment and all other users of NLA_POLICY_VALIDATE_FN().
As a result, move the length validation to the validation function.
When RISCV port was imported in 5.2, the O_* macros were taken with
their octal value and written as-is in hex, resulting in the getdents64()
to fail in nolibc-test.
Depending on the compiler used and the optimization options, the sbrk()
test was crashing, both on real hardware (mips-24kc) and in qemu. One
such example is kernel.org toolchain in version 11.3 optimizing at -Os.
Inspecting the sys_brk() call shows the following code:
It is obviously wrong, the "negu" instruction is placed in beqz's
delayed slot, and worse, there's no nop nor instruction after the
return, so the next function's first instruction (addiu sip,sip,-32)
will also be executed as part of the delayed slot that follows the
return.
This is caused by the ".set noreorder" directive in the _start block,
that applies to the whole program. The compiler emits code without the
delayed slots and relies on the compiler to swap instructions when this
option is not set. Removing the option would require to change the
startup code in a way that wouldn't make it look like the resulting
code, which would not be easy to debug. Instead let's just save the
default ordering before changing it, and restore it at the end of the
_start block. Now the code is correct:
Building with clang yields the following error:
```
<inline asm>:3:1: error: _start changed binding to STB_GLOBAL
.global _start
^
1 error generated.
```
Make sure only specify one between `.global _start` and `.weak _start`.
Remove `.global _start`.
Cc: llvm@lists.linux.dev Reviewed-by: Nick Desaulniers <ndesaulniers@google.com> Acked-by: Willy Tarreau <w@1wt.eu> Signed-off-by: Ammar Faizi <ammarfaizi2@gnuweeb.org> Signed-off-by: Paul E. McKenney <paulmck@kernel.org>
Stable-dep-of: 184177c3d6e0 ("tools/nolibc: restore mips branch ordering in the _start block") Signed-off-by: Sasha Levin <sashal@kernel.org>
In order to ease maintenance, this splits the arch-specific code into
one file per architecture. A common file "arch.h" is used to include the
right file among arch-* based on the detected architecture. Projects
which are already split per architecture could simply rename these
files to $arch/arch.h and get rid of the common arch.h. For this
reason, include guards were placed into each arch-specific file.
Signed-off-by: Willy Tarreau <w@1wt.eu> Signed-off-by: Paul E. McKenney <paulmck@kernel.org>
Stable-dep-of: 184177c3d6e0 ("tools/nolibc: restore mips branch ordering in the _start block") Signed-off-by: Sasha Levin <sashal@kernel.org>
projects / linux.git / log