Kevin Lo [Fri, 8 Mar 2024 15:09:45 +0000 (17:09 +0200)]
wifi: ath11k: adjust a comment to reflect reality
On QCA6390/QCN9074/WCN6855, MHISTATUS may still have SYSERR bit set
after SOC_GLOBAL_RESET.
Signed-off-by: Kevin Lo <kevlo@kevlo.org>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/ZeWEqGVibkMg2APi@ns.kevlo.org
Baochen Qiang [Wed, 6 Mar 2024 05:15:14 +0000 (07:15 +0200)]
wifi: ath10k: poll service ready message before failing
Currently host relies on CE interrupts to get notified that
the service ready message is ready. This results in timeout
issue if the interrupt is not fired, due to some unknown
reasons. See below logs:
[76321.937866] ath10k_pci 0000:02:00.0: wmi service ready event not received
...
[76322.016738] ath10k_pci 0000:02:00.0: Could not init core: -110
And finally it causes WLAN interface bring up failure.
Change to give it one more chance here by polling CE rings,
before failing directly.
Tested-on: QCA6174 hw3.2 PCI WLAN.RM.4.4.1-00157-QCARMSWPZ-1
Fixes: 5e3dd157d7e7 ("ath10k: mac80211 driver for Qualcomm Atheros 802.11ac CQA98xx devices")
Reported-by: James Prestwood <prestwoj@gmail.com>
Tested-By: James Prestwood <prestwoj@gmail.com> # on QCA6174 hw3.2
Link: https://lore.kernel.org/linux-wireless/304ce305-fbe6-420e-ac2a-d61ae5e6ca1a@gmail.com/
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240227030409.89702-1-quic_bqiang@quicinc.com
Jeff Johnson [Tue, 5 Mar 2024 15:14:00 +0000 (07:14 -0800)]
wifi: ath11k: fix soc_dp_stats debugfs file permission
Currently the soc_dp_stats debugfs file has the following permissions:
# ls -l /sys/kernel/debug/ath11k/pci-0000:03:00.0/soc_dp_stats
-rw------- 1 root root 0 Mar 4 15:04 /sys/kernel/debug/ath11k/pci-0000:03:00.0/soc_dp_stats
However this file does not actually support write operations -- no .write()
method is registered. Therefore use the correct permissions when creating
the file.
After the change:
# ls -l /sys/kernel/debug/ath11k/pci-0000:03:00.0/soc_dp_stats
-r-------- 1 root root 0 Mar 4 15:15 /sys/kernel/debug/ath11k/pci-0000:03:00.0/soc_dp_stats
Tested-on: WCN6855 hw2.1 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3.6510.30
Signed-off-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240305-fix-soc_dp_stats-permission-v1-1-2ec10b42f755@quicinc.com
Jeff Johnson [Wed, 6 Mar 2024 05:15:14 +0000 (07:15 +0200)]
wifi: ath11k: remove obsolete struct wmi_start_scan_arg
ath11k inherited struct wmi_start_scan_arg from ath10k. However, in
ath11k, this struct is unused -- struct scan_req_params is used for
this functionality. So remove the unused struct.
No functional changes, compile tested only.
Signed-off-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240226-ath11k-obsolete-wmi_start_scan_arg-v1-1-c0b94c6e191d@quicinc.com
Jeff Johnson [Wed, 6 Mar 2024 05:15:14 +0000 (07:15 +0200)]
wifi: ath12k: remove obsolete struct wmi_start_scan_arg
ath12k inherited struct wmi_start_scan_arg from ath11k. However, in
ath12k, this struct is unused -- struct ath12k_wmi_scan_req_arg is
used for this functionality. So remove the unused struct.
No functional changes, compile tested only.
Signed-off-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240226-ath12k-obsolete-wmi_start_scan_arg-v1-1-07b0b563cb27@quicinc.com
Kalle Valo [Tue, 5 Mar 2024 18:57:28 +0000 (20:57 +0200)]
Merge tag 'ath-next-
20240305' of git://git./linux/kernel/git/kvalo/ath
ath.git patches for v6.9
Only some minor cleanup in ath11k and ath12k. Adding Jeff as the
maintainer for ath10k, ath11k and ath12k DT bindings.
Chin-Yen Lee [Sat, 2 Mar 2024 00:58:28 +0000 (08:58 +0800)]
wifi: rtw89: wow: move release offload packet earlier for WoWLAN mode
Now WoWLAN firmware will disable PCIE DMA after driver call cfg_wake
function, and it will lead to release offload packet fail because driver
can't receive completion notification from firmware. We move release
offload packet earlier to avoid this error.
Signed-off-by: Chin-Yen Lee <timlee@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240302005828.13666-8-pkshih@realtek.com
Chin-Yen Lee [Sat, 2 Mar 2024 00:58:27 +0000 (08:58 +0800)]
wifi: rtw89: wow: set security engine options for 802.11ax chips only
The security engine is set for management frames by default for 802.11be
chips, so no need to set it in WoWLAN flow.
Signed-off-by: Chin-Yen Lee <timlee@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240302005828.13666-7-pkshih@realtek.com
Chin-Yen Lee [Sat, 2 Mar 2024 00:58:26 +0000 (08:58 +0800)]
wifi: rtw89: update suspend/resume for different generation
The setting during suspend or resume is different between different
generation, so update it.
Signed-off-by: Chin-Yen Lee <timlee@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240302005828.13666-6-pkshih@realtek.com
Chin-Yen Lee [Sat, 2 Mar 2024 00:58:25 +0000 (08:58 +0800)]
wifi: rtw89: wow: update config mac function with different generation
The registers to configure mac function for WoWLAN mode that are different
from different generation, so update them.
Signed-off-by: Chin-Yen Lee <timlee@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240302005828.13666-5-pkshih@realtek.com
Chin-Yen Lee [Sat, 2 Mar 2024 00:58:24 +0000 (08:58 +0800)]
wifi: rtw89: update DMA function with different generation
The register of control and polling function for TX/RX DMA is different
from different generation, so update them. Also rename polling_dma
function to polling_dma_idle to avoid misunderstanding.
Signed-off-by: Chin-Yen Lee <timlee@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240302005828.13666-4-pkshih@realtek.com
Chin-Yen Lee [Sat, 2 Mar 2024 00:58:23 +0000 (08:58 +0800)]
wifi: rtw89: wow: update WoWLAN status register for different generation
The statue register is for driver to check if WoWLAN mode works or stops
successfully. It is changed for new generation, so update it.
Signed-off-by: Chin-Yen Lee <timlee@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240302005828.13666-3-pkshih@realtek.com
Chin-Yen Lee [Sat, 2 Mar 2024 00:58:22 +0000 (08:58 +0800)]
wifi: rtw89: wow: update WoWLAN reason register for different chips
The WoWLAN reason register is used for driver to get the wakeup reason
for reporting to cfg80211, and it is different from chips. So put it
into chip information.
Signed-off-by: Chin-Yen Lee <timlee@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240302005828.13666-2-pkshih@realtek.com
Duoming Zhou [Thu, 29 Feb 2024 10:31:53 +0000 (18:31 +0800)]
wifi: brcm80211: handle pmk_op allocation failure
The kzalloc() in brcmf_pmksa_v3_op() will return null if the
physical memory has run out. As a result, if we dereference
the null value, the null pointer dereference bug will happen.
Return -ENOMEM from brcmf_pmksa_v3_op() if kzalloc() fails
for pmk_op.
Fixes: a96202acaea4 ("wifi: brcmfmac: cfg80211: Add support for PMKID_V3 operations")
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Duoming Zhou <duoming@zju.edu.cn>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240229103153.18533-1-duoming@zju.edu.cn
Ching-Te Ku [Thu, 29 Feb 2024 07:45:14 +0000 (15:45 +0800)]
wifi: rtw89: coex: Add coexistence policy to decrease WiFi packet CRC-ERR
The 2 Bluetooth profiles (Hands free profile & Human interface device)
have high duty transmission, it will affect the traffic of WiFi packet
frequently. And once the WiFi traffic down to B/G mode, it will need
a better success rate to recover the transmission rate. Add new policy
option to solve the above situation.
Signed-off-by: Ching-Te Ku <ku920601@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240229074514.219276-9-pkshih@realtek.com
Ching-Te Ku [Thu, 29 Feb 2024 07:45:13 +0000 (15:45 +0800)]
wifi: rtw89: coex: When Bluetooth not available don't set power/gain
If Bluetooth is working, it will update their info regularly. And the code
will increase the counters while the info updating. Use this counter to
judge is Bluetooth working or not. Don't need to set Bluetooth power or
gain when it is not working.
Signed-off-by: Ching-Te Ku <ku920601@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240229074514.219276-8-pkshih@realtek.com
Ching-Te Ku [Thu, 29 Feb 2024 07:45:12 +0000 (15:45 +0800)]
wifi: rtw89: coex: add return value to ensure H2C command is success or not
Add return value to H2C function, and only record down the value while
H2C command success, this can help us to check the real time status.
Signed-off-by: Ching-Te Ku <ku920601@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240229074514.219276-7-pkshih@realtek.com
Ching-Te Ku [Thu, 29 Feb 2024 07:45:11 +0000 (15:45 +0800)]
wifi: rtw89: coex: Reorder H2C command index to align with firmware
Wi-Fi firmware need some driver information to do decision or do some
real-time control. Driver will update these information by H2C command.
The chip 8922a H2C command index is different from before chips/branch,
so need to assign the correct index to let firmware parsing.
Signed-off-by: Ching-Te Ku <ku920601@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240229074514.219276-6-pkshih@realtek.com
Ching-Te Ku [Thu, 29 Feb 2024 07:45:10 +0000 (15:45 +0800)]
wifi: rtw89: coex: add BTC ctrl_info version 7 and related logic
Change structure member from bit field to normal variable to
reduce unnecessary translation.
Signed-off-by: Ching-Te Ku <ku920601@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240229074514.219276-5-pkshih@realtek.com
Ching-Te Ku [Thu, 29 Feb 2024 07:45:09 +0000 (15:45 +0800)]
wifi: rtw89: coex: add init_info H2C command format version 7
To avoid using bit fields for H2C command, rearrange the structure.
And also patch the corresponding code for the using of this structure.
No logic changes for existing chips.
Signed-off-by: Ching-Te Ku <ku920601@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240229074514.219276-4-pkshih@realtek.com
Ping-Ke Shih [Thu, 29 Feb 2024 07:45:08 +0000 (15:45 +0800)]
wifi: rtw89: 8922a: add coexistence helpers of SW grant
Under some circumstances, coexistence mechanism want to keep grant BT or
WiFi, such as inquiry and WiFi is connecting, to ensure BT or WiFi can
transmit or receive data in that period.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240229074514.219276-3-pkshih@realtek.com
Ping-Ke Shih [Thu, 29 Feb 2024 07:45:07 +0000 (15:45 +0800)]
wifi: rtw89: mac: add coexistence helpers {cfg/get}_plt
When hardware grant BT initially but transition to grant WiFi, the PLT
(polluted) bit is set to assist coexistence mechanism to debug if
grant signal is expected.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240229074514.219276-2-pkshih@realtek.com
Johannes Berg [Wed, 28 Feb 2024 11:11:56 +0000 (12:11 +0100)]
wifi: cw1200: restore endian swapping
The code here looks well thought-out, so it seems likely
that the byte-swaps are actually needed, due to SPI bus
and device behaviour. Restore the byte-swapping, in a way
that doesn't result in sparse warnings.
Fixes: 7ceade653429 ("wifi: cw1200: fix __le16 sparse warnings")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240228121156.62f820aa6dfb.Ia63314e4d0ed1ee76f100846d68f0722abf6b793@changeid
Javier Martinez Canillas [Wed, 28 Feb 2024 10:10:32 +0000 (11:10 +0100)]
wifi: wlcore: sdio: Rate limit wl12xx_sdio_raw_{read,write}() failures warns
When these failures happen, the warning and call trace is printed which is
excessive. Instead, just print the error but rate limited to prevent warns
to unnecessarily pollute the kernel log buffer and make the serial console
practically unusable.
For example, on an AM625 BeaglePlay board where accessing a SDIO WiFi chip
fails with an -110 (ETIMEDOUT) error:
$ dmesg | grep "sdio write\|read failed (-110)" | wc -l
39
Signed-off-by: Javier Martinez Canillas <javierm@redhat.com>
Reviewed-by: Breno Leitao <leitao@debian.org>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240228101042.728881-1-javierm@redhat.com
Bitterblue Smith [Tue, 27 Feb 2024 12:15:52 +0000 (14:15 +0200)]
wifi: rtlwifi: Remove rtl_intf_ops.read_efuse_byte
PCI drivers and USB drivers can both use the same function,
read_efuse_byte(), and they can call it directly.
rtl8192de was the only user.
Tested only with the upcoming rtl8192du driver.
Signed-off-by: Bitterblue Smith <rtl8821cerfe2@gmail.com>
Acked-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/4e2c968d-f25c-4a40-be97-4fdcbdde69cf@gmail.com
Bitterblue Smith [Thu, 29 Feb 2024 22:35:58 +0000 (00:35 +0200)]
wifi: rtw88: 8821c: Fix false alarm count
total_fa_cnt is supposed to include cck_fa_cnt and ofdm_fa_cnt, not just
ofdm_fa_cnt.
Fixes: 960361238b86 ("rtw88: 8821c: add false alarm statistics")
Signed-off-by: Bitterblue Smith <rtl8821cerfe2@gmail.com>
Acked-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/f3cb6d17-e4e4-44a7-9c9b-72aed994b5c9@gmail.com
Bitterblue Smith [Thu, 29 Feb 2024 22:35:09 +0000 (00:35 +0200)]
wifi: rtw88: 8821c: Fix beacon loss and disconnect
Tenda U9 V2.0, which contains RTL8811CU, is practically unusable because
of frequent disconnections:
Feb 23 14:46:45 ideapad2 wpa_supplicant[427]: wlp3s0f3u2: CTRL-EVENT-BEACON-LOSS
Feb 23 14:46:46 ideapad2 wpa_supplicant[427]: wlp3s0f3u2: CTRL-EVENT-DISCONNECTED
bssid=90:55:de:__:__:__ reason=4 locally_generated=1
Feb 23 14:46:52 ideapad2 wpa_supplicant[427]: wlp3s0f3u2: CTRL-EVENT-CONNECTED
- Connection to 90:55:de:__:__:__ completed [id=0 id_str=]
Feb 23 14:46:54 ideapad2 wpa_supplicant[427]: wlp3s0f3u2: CTRL-EVENT-BEACON-LOSS
Feb 23 14:46:55 ideapad2 wpa_supplicant[427]: wlp3s0f3u2: CTRL-EVENT-DISCONNECTED
bssid=90:55:de:__:__:__ reason=4 locally_generated=1
Feb 23 14:47:01 ideapad2 wpa_supplicant[427]: wlp3s0f3u2: CTRL-EVENT-CONNECTED
- Connection to 90:55:de:__:__:__ completed [id=0 id_str=]
Feb 23 14:47:04 ideapad2 wpa_supplicant[427]: wlp3s0f3u2: CTRL-EVENT-BEACON-LOSS
Feb 23 14:47:05 ideapad2 wpa_supplicant[427]: wlp3s0f3u2: CTRL-EVENT-DISCONNECTED
bssid=90:55:de:__:__:__ reason=4 locally_generated=1
This is caused by a mistake in the chip initialisation. This version of
the chip requires loading an extra AGC table right after the main one,
but the extra table is being loaded at the wrong time, in
rtw_chip_board_info_setup().
Move the extra AGC table loading to the right place, in
rtw_phy_load_tables().
The rtw_chip_board_info_setup() can only do "software" things, and
rtw_phy_load_tables() can really do IO.
Fixes: 5d6651fe8583 ("rtw88: 8821c: support RFE type2 wifi NIC")
Signed-off-by: Bitterblue Smith <rtl8821cerfe2@gmail.com>
Acked-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/276c31d8-b9a8-4e54-a3ac-09b74657aff7@gmail.com
Bitterblue Smith [Thu, 29 Feb 2024 22:34:13 +0000 (00:34 +0200)]
wifi: rtw88: 8821cu: Fix connection failure
Clear bit 8 of REG_SYS_STATUS1 after MAC power on.
Without this, some RTL8821CU and RTL8811CU cannot connect to any
network:
Feb 19 13:33:11 ideapad2 kernel: wlp3s0f3u2: send auth to
90:55:de:__:__:__ (try 1/3)
Feb 19 13:33:13 ideapad2 kernel: wlp3s0f3u2: send auth to
90:55:de:__:__:__ (try 2/3)
Feb 19 13:33:14 ideapad2 kernel: wlp3s0f3u2: send auth to
90:55:de:__:__:__ (try 3/3)
Feb 19 13:33:15 ideapad2 kernel: wlp3s0f3u2: authentication with
90:55:de:__:__:__ timed out
The RTL8822CU and RTL8822BU out-of-tree drivers do this as well, so do
it for all three types of chips.
Tested with RTL8811CU (Tenda U9 V2.0).
Signed-off-by: Bitterblue Smith <rtl8821cerfe2@gmail.com>
Acked-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/aeeefad9-27c8-4506-a510-ef9a9a8731a4@gmail.com
Bitterblue Smith [Thu, 29 Feb 2024 22:32:45 +0000 (00:32 +0200)]
wifi: rtw88: 8821cu: Fix firmware upload fail
RTL8822CU, RTL8822BU, and RTL8821CU need an extra register write after
reading and writing certain addresses.
Without this, the firmware upload fails approximately more than 50% of
the time.
Tested with RTL8811CU (Tenda U9 V2.0) which is the same as RTL8821CU
but without Bluetooth.
Fixes: a82dfd33d123 ("wifi: rtw88: Add common USB chip support")
Signed-off-by: Bitterblue Smith <rtl8821cerfe2@gmail.com>
Acked-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/f12ed39d-28e8-4b8b-8d22-447bcf295afc@gmail.com
Nick Morrow [Tue, 27 Feb 2024 02:34:40 +0000 (02:34 +0000)]
wifi: rtw88: Add missing VID/PIDs for 8811CU and 8821CU
Add VID/PIDs that are known to be missing for this driver.
Removed /* 8811CU */ and /* 8821CU */ as they are redundant
since the file is specific to those chips.
Removed /* TOTOLINK A650UA v3 */ as the manufacturer. It has a REALTEK
VID so it may not be specific to this adapter.
Verified and tested.
Cc: stable@vger.kernel.org
Signed-off-by: Nick Morrow <morrownr@gmail.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Acked-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/4ume7mjw63u7.XlMUvUuacW2ErhOCdqlLkw2@1EHFQ.trk.elasticemail.com
Johannes Berg [Wed, 28 Feb 2024 08:55:48 +0000 (09:55 +0100)]
wifi: mac80211: remove TDLS peers on link deactivation
If a link is deactivated, we really cannot sustain any
TDLS connections on that link any more. With the API
now changed, fix this issue and remove TDLS connections.
Reviewed-by: Miriam Rachel Korenblit <miriam.rachel.korenblit@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Link: https://msgid.link/20240228095719.a7dd812c37bf.I3474dbde79e9e7a539d47f6f81f32e6c3e459080@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Johannes Berg [Wed, 28 Feb 2024 08:55:47 +0000 (09:55 +0100)]
wifi: mac80211: remove TDLS peers only on affected link
If a link does CSA, or if it changes SMPS mode, we need to
drop the TDLS peers, but we really should drop them only on
the affected link. Fix that.
Reviewed-by: Miriam Rachel Korenblit <miriam.rachel.korenblit@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Link: https://msgid.link/20240228095719.00d1d793f5b8.Ia9971316c6b3922dd371d64ac2198f91ed5ad9d2@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Johannes Berg [Wed, 28 Feb 2024 08:55:46 +0000 (09:55 +0100)]
wifi: mac80211: mlme: unify CSA handling
Unify all the CSA handling, including handling of a beacon
after the CSA, into ieee80211_sta_process_chanswitch().
The CRC of the beacon will change due to changes in the
CSA/ECSA elements, so there's really no need to have the
'beacon after CSA' handling before the CRC processing or
to change the beacon_crc_valid value here.
Reviewed-by: Miriam Rachel Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240228095719.e269c0e02905.I9dc68ff1e84d51349822bc7d3b33b578fcf8e360@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Johannes Berg [Wed, 28 Feb 2024 08:55:45 +0000 (09:55 +0100)]
wifi: mac80211: introduce a feature flag for quiet in CSA
When doing CSA in multi-link, there really isn't a need to
stop transmissions entirely. Add a feature flag for drivers
to indicate they can handle quiet in CSA (be it by parsing
themselves, or by implementing drv_pre_channel_switch()),
to make that possible.
Also clean up the csa_block_tx handling: it clearly cannot
handle multi-link due to the way queues are stopped, move
it to the sdata. Drivers should be doing it themselves for
working properly during CSA in MLO anyway. Also rename it
to indicate that it reflects TX was blocked at mac80211.
Reviewed-by: Miriam Rachel Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240228095719.258439191541.I2469d206e2bf5cb244cfde2b4bbc2ae6d1cd3dd9@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Johannes Berg [Wed, 28 Feb 2024 08:55:44 +0000 (09:55 +0100)]
wifi: mac80211: pass link conf to abort_channel_switch
Pass the link conf to the abort_channel_switch driver
method so the driver can handle things correctly.
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Reviewed-by: Miriam Rachel Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240228095718.27f621106ddd.Iadd3d69b722ffe5934779a32a0e4e596a4e33ed4@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Johannes Berg [Wed, 28 Feb 2024 08:55:43 +0000 (09:55 +0100)]
wifi: mac80211: pass link_id to channel switch ops
For CSA to work correctly in multi-link scenarios, pass
the link_id to the relevant callbacks.
While at it, unify/deduplicate the tracing for them.
Reviewed-by: Miriam Rachel Korenblit <miriam.rachel.korenblit@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Link: https://msgid.link/20240228095718.b7726635c054.I0be5d00af4acb48cfbd23a9dbf067f9aeb66469d@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Johannes Berg [Wed, 28 Feb 2024 08:55:42 +0000 (09:55 +0100)]
wifi: cfg80211: allow cfg80211_defragment_element() without output
If we just want to determine the length of the fragmented
data, we basically need the same logic, and really we want
it to be _literally_ the same logic, so it cannot be out
of sync in any way.
Allow calling cfg80211_defragment_element() without an output
buffer, where it then just returns the required output size.
Also add this to the tests, just to exercise it, using the
pre-calculated length to really do the defragmentation, which
checks that this is sufficient.
Reviewed-by: Miriam Rachel Korenblit <miriam.rachel.korenblit@intel.com>
Reviewed-by: Benjamin Berg <benjamin.berg@intel.com>
Link: https://msgid.link/20240228095718.6d6565b9e3f2.Ib441903f4b8644ba04b1c766f90580ee6f54fc66@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Johannes Berg [Wed, 28 Feb 2024 08:55:41 +0000 (09:55 +0100)]
wifi: cfg80211: expose cfg80211_iter_rnr() to drivers
In mac80211 we'll need to look at reduced neighbor report
entries for channel switch purposes, so export the iteration
function to make that simpler.
Reviewed-by: Miriam Rachel Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240228095718.0954809964ef.I53e95c017aa71f14e8d1057afbbc75982ddb43df@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Johannes Berg [Wed, 28 Feb 2024 08:48:16 +0000 (09:48 +0100)]
wifi: mac80211: hide element parsing internals
Rework the data structures to hide element parsing internals
from the users.
Reviewed-by: Miriam Rachel Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240228094902.19c610b529e2.Ie7ea2dcb6713911590ace6583a4748f32dc37df2@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Johannes Berg [Wed, 28 Feb 2024 08:48:15 +0000 (09:48 +0100)]
wifi: mac80211: remove unneeded scratch_len subtraction
We're always using "scratch + len - pos", so we don't need
to subtract here to calculate the remaining length. Remove
the unnecessary subtraction.
Reviewed-by: Miriam Rachel Korenblit <miriam.rachel.korenblit@intel.com>
Reviewed-by: Ilan Peer <ilan.peer@intel.com>
Link: https://msgid.link/20240228094902.44e07cfa9e63.I7a9758fb9bc6b726aac49804f2f05cd521bc4128@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Johannes Berg [Wed, 28 Feb 2024 08:48:14 +0000 (09:48 +0100)]
wifi: mac80211: defragment reconfiguration MLE when parsing
Using the scratch buffer (without advancing it) here in the
mlme.c code seems somewhat wrong, defragment the reconfig
multi-link element already when parsing. This might be a bit
more work in certain cases, but makes the whole thing more
regular.
Reviewed-by: Miriam Rachel Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240228094902.92936a3ce216.I4b736ce4fdc199fa1d6b00d00032f448c873a8b4@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Johannes Berg [Wed, 28 Feb 2024 08:48:13 +0000 (09:48 +0100)]
wifi: mac80211: simplify multi-link element parsing
We shouldn't assign elems->ml_basic{,len} before defragmentation,
and we don't need elems->ml_reconf{,len} at all since we don't do
defragmentation. Clean that up a bit. This does require always
defragmention even when it may not be needed, but that's easier
to reason about.
Reviewed-by: Ilan Peer <ilan.peer@intel.com>
Reviewed-by: Miriam Rachel Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240228094902.e0115da4d2a6.I89a80f7387eabef8df3955485d4a583ed024c5b1@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Johannes Berg [Wed, 28 Feb 2024 08:48:12 +0000 (09:48 +0100)]
wifi: mac80211: remove unnecessary ML element checks
Given the prior changes to ieee80211_mle_size_ok(), we
can now pass NULL to for_each_mle_subelement(), so no
longer need to check for that here explicitly.
Reviewed-by: Miriam Rachel Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240228094901.9e32c4b63875.Ia2ee0aafdc8a48bd21b485cc36a9866f950d781b@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Johannes Berg [Wed, 28 Feb 2024 08:48:11 +0000 (09:48 +0100)]
wifi: mac80211: add ieee80211_vif_link_active() helper
We sometimes need to check if a link is active, and this
is complicated by the fact that active_links has no bits
set when the vif isn't (acting as) an MLD. Add a small
new helper ieee80211_vif_link_active() to make that a bit
easier, and use it in a few places.
Reviewed-by: Ilan Peer <ilan.peer@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Reviewed-by: Miriam Rachel Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240228094901.688760aff5f7.I06892a503f5ecb9563fbd678d35d08daf7a044b0@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Johannes Berg [Wed, 28 Feb 2024 08:48:10 +0000 (09:48 +0100)]
wifi: mac80211: remove unnecessary ML element type check
At this point, since it's taken from elems->ml_basic which
is stored only if it's of type basic, we don't really need
to check again if it's basic.
Reviewed-by: Ilan Peer <ilan.peer@intel.com>
Reviewed-by: Miriam Rachel Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240228094901.ad1d4a09a6eb.Ib96fa75b1a6db21dd4182dcfa11fe9aff78fa3ed@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Johannes Berg [Wed, 28 Feb 2024 08:48:09 +0000 (09:48 +0100)]
wifi: mac80211: update scratch_pos after defrag
The scratch_pos update here was lost after defrag, so any
other uses of the scratch buffer might overwrite it.
Fixes: a286de1aa38f ("wifi: mac80211: Rename multi_link")
Reviewed-by: Benjamin Berg <benjamin.berg@intel.com>
Reviewed-by: Ilan Peer <ilan.peer@intel.com>
Reviewed-by: Miriam Rachel Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240228094901.9da35f39eeb7.I7127f2918ec4cba416fcbc35eacaea10262c1268@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Ilan Peer [Wed, 28 Feb 2024 08:47:54 +0000 (09:47 +0100)]
wifi: mac80211: Adjust CQM handling for MLO
The CQM handling did not consider the MLO case and thus notified
a not-existing link with the CQM change. To fix this, propagate
the CQM notification to all the active links (handling both the
non-MLO and MLO cases).
TODO: this currently propagates the same configuration to all
links regardless of the band. This might not be the correct
approach as different links might need to be configured with
different values.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Reviewed-by: Miriam Rachel Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240228094753.bf6a3fefe553.Id738810b73e1087e01d5885508b70a3631707627@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Ilan Peer [Wed, 28 Feb 2024 08:47:39 +0000 (09:47 +0100)]
wifi: mac80211: Allow beacons to update BSS table regardless of scan
When a beacon is received use it to update the BSS table regardless
of the scanning state. Do so only when there are active non-monitor
interfaces. Also, while at it, in any case accept beacons only with
broadcast address.
Reviewed-by: Miriam Rachel Korenblit <miriam.rachel.korenblit@intel.com>
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Link: https://msgid.link/20240228094742.e508605f495b.I3ab24ab3543319e31165111b28bcdcc622b5cf02@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Shaul Triebitz [Wed, 28 Feb 2024 08:44:56 +0000 (09:44 +0100)]
wifi: mac80211: add link id to ieee80211_gtk_rekey_add()
In MLO, we need the link id in the GTK key to be given by
the driver after rekeying in wowlan, so add that.
Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com>
Reviewed-by: Miriam Rachel Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240228094500.ce1bfc83a680.I43a6f8ab2804ee07116a37d5b9ec601b843464b1@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Johannes Berg [Wed, 28 Feb 2024 08:42:54 +0000 (09:42 +0100)]
wifi: cfg80211: print flags in tracing in hex
It's confusing to see decimal, e.g. 20, here. Printing
the flags in hex (0x14 == 20) is much clearer.
Reviewed-by: Miriam Rachel Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240228094254.5f7f4ab2e137.Id5e665104bbc51377b4591289e32f8c1d4711dce@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Johannes Berg [Wed, 28 Feb 2024 08:40:52 +0000 (09:40 +0100)]
wifi: mac80211: obtain AP HT/VHT data for assoc request
In the association request, we make some parameters depend on the
AP's HT/VHT information. This was broken by my code because it no
longer filled that information, making it all zero.
For HT that meant we wouldn't reduce our capabilities to 20 MHz if
needed, and for VHT we lost beamforming capabilities.
Fix this. It seems like it may even have been broken for all but
the assoc link before.
Fixes: 310c8387c638 ("wifi: mac80211: clean up connection process")
Reviewed-by: Miriam Rachel Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240228094207.7dc812c2060a.Ibd591f9c214b4e166cf7171db3cf63bda8e3c9fd@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Johannes Berg [Wed, 28 Feb 2024 08:40:51 +0000 (09:40 +0100)]
wifi: mac80211: don't add VHT capa on links without them
When a link doesn't have VHT capability, before the rework
we'd have set IEEE80211_CONN_DISABLE_VHT, but now with the
linear progression of 'mode', we no longer have that. Add
an explicit check for VHT being supported, so we don't add
a zeroed VHT capabilities element where it shouldn't be.
Fixes: 310c8387c638 ("wifi: mac80211: clean up connection process")
Reviewed-by: Miriam Rachel Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240228094207.bfe4283bcde7.Ib70a558bc6bdbcec3d9e663079229dfcc2493682@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Aditya Kumar Singh [Tue, 27 Feb 2024 04:22:51 +0000 (09:52 +0530)]
wifi: mac80211: handle netif carrier up/down with link AP during MLO
Currently whenever link AP is started, netif_carrier_up() function is
called and whenever it is brought down, netif_carrier_down() function is
called. However, with MLO, all the links of the same MLD would use the
same netdev. Hence there is no need to indicate for each link up/down.
Also, calling it down when only one of the links went down is not
desirable.
Add changes to call the netif_carrier_up() function only when first link
is brought up. Similarly, add changes to call the netif_carrier_down()
function only when last link is brought down.
In order to check the number of beaconing links in the given interface,
introduce a new helper function ieee80211_num_beaconing_links().
Signed-off-by: Aditya Kumar Singh <quic_adisi@quicinc.com>
Link: https://msgid.link/20240227042251.1511122-3-quic_adisi@quicinc.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Rameshkumar Sundaram [Tue, 27 Feb 2024 04:22:50 +0000 (09:52 +0530)]
wifi: mac80211: remove only link keys during stopping link AP
Currently while stopping a link AP, all keys from the interface were
removed. However with MLO there is a requirement to free only the link
keys.
Add changes to remove keys which are associated with the link AP which is
going to be stopped.
Signed-off-by: Rameshkumar Sundaram <quic_ramess@quicinc.com>
Signed-off-by: Aditya Kumar Singh <quic_adisi@quicinc.com>
Link: https://msgid.link/20240227042251.1511122-2-quic_adisi@quicinc.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Johannes Berg [Mon, 26 Feb 2024 19:34:06 +0000 (20:34 +0100)]
wifi: cfg80211: check A-MSDU format more carefully
If it looks like there's another subframe in the A-MSDU
but the header isn't fully there, we can end up reading
data out of bounds, only to discard later. Make this a
bit more careful and check if the subframe header can
even be present.
Reported-by: syzbot+d050d437fe47d479d210@syzkaller.appspotmail.com
Link: https://msgid.link/20240226203405.a731e2c95e38.I82ce7d8c0cc8970ce29d0a39fdc07f1ffc425be4@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Takashi Iwai [Wed, 28 Feb 2024 16:38:37 +0000 (17:38 +0100)]
wifi: iwlwifi: Add missing MODULE_FIRMWARE() for *.pnvm
A few models require *.pnvm files while we don't declare them via
MODULE_FIRMWARE(). This resulted in the breakage of WiFi on the
system that relies on the information from modinfo (e.g. openSUSE
installer image).
This patch adds those missing MODULE_FIRMWARE() entries for *.pnvm
files.
type=feature
ticket=none
Link: https://bugzilla.opensuse.org/show_bug.cgi?id=1207553
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Link: https://msgid.link/20240228163837.4320-1-tiwai@suse.de
[move to appropriate files]
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Johannes Berg [Wed, 28 Feb 2024 11:01:57 +0000 (12:01 +0100)]
wifi: mac80211: track capability/opmode NSS separately
We're currently tracking rx_nss for each station, and that
is meant to be initialized to the capability NSS and later
reduced by the operating mode notification NSS.
However, we're mixing up capabilities and operating mode
NSS in the same variable. This forces us to recalculate
the NSS capability on operating mode notification RX,
which is a bit strange; due to the previous fix I had to
never keep rx_nss as zero, it also means that the capa is
never taken into account properly.
Fix all this by storing the capability value, that can be
recalculated unconditionally whenever needed, and storing
the operating mode notification NSS separately, taking it
into account when assigning the final rx_nss value.
Cc: stable@vger.kernel.org
Fixes: dd6c064cfc3f ("wifi: mac80211: set station RX-NSS on reconfig")
Reviewed-by: Miriam Rachel Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240228120157.0e1c41924d1d.I0acaa234e0267227b7e3ef81a59117c8792116bc@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Johannes Berg [Fri, 1 Mar 2024 16:54:51 +0000 (17:54 +0100)]
wifi: mac80211: fix supported rate masking in scan
We have an nl80211 attribute to mask supported rates from
probe responses in scanning, e.g. for use in P2P, but in
the refactoring I stopped applying this mask. Restore it.
Fixes: 07095d167749 ("wifi: mac80211: start building elements in SKBs")
Link: https://msgid.link/20240301175451.7ad8ab0bd90c.I46b49e4fc27fe60b75d4559c01104e55ed381c37@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Johannes Berg [Fri, 1 Mar 2024 18:36:33 +0000 (19:36 +0100)]
wifi: mac80211: check link exists before use
If the assoc link doesn't exist yet at this point, we
cannot use it yet. This isn't normally the case, but
e.g. in case of FT-DS (or just broken userspace) the
link might not be set up yet and will only be created
later in this function. Check that the link exists.
Fixes: 310c8387c638 ("wifi: mac80211: clean up connection process")
Reported-by: Dan Carpenter <dan.carpenter@linaro.org>
Closes: https://lore.kernel.org/r/3151f5d0-c18f-413d-b34b-b94f095b947c@moroto.mountain
Reviewed-by: Miriam Rachel Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240301193633.c886d300e90a.Ie1d5e23b2a033d934d343c37249f6f4dfddcc5fe@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Johannes Berg [Fri, 1 Mar 2024 18:36:32 +0000 (19:36 +0100)]
wifi: mac80211: always initialize match_auth
My previous patch only initialized match_auth when the
ifmgd->auth_data exists, but that was wrong, it should
always be set. Fix that.
Fixes: 310c8387c638 ("wifi: mac80211: clean up connection process")
Reported-by: Dan Carpenter <dan.carpenter@linaro.org>
Closes: https://lore.kernel.org/r/3151f5d0-c18f-413d-b34b-b94f095b947c@moroto.mountain
Reviewed-by: Miriam Rachel Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240301193633.1a3fc370f211.I979dd222b3b5eb5e1437886e5f7c2355eeccb9f7@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Kalle Valo [Mon, 26 Feb 2024 18:07:45 +0000 (20:07 +0200)]
wifi: ath12k: fix license in p2p.c and p2p.h
ath12k uses BSD-3-Clause-Clear, not ISC.
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240226180745.3195805-1-kvalo@kernel.org
Jeff Johnson [Fri, 23 Feb 2024 15:39:31 +0000 (07:39 -0800)]
wifi: ath11k: constify MHI channel and controller configs
Unlike the event configuration which can be modified by MHI, the
channel and controller configurations are expected to be const. And
since they are not modified locally, constify them to prevent runtime
modification.
No functional changes, compile tested only.
Signed-off-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240223-mhi-const-wifi-ath11k-v1-1-51b9d42d2639@quicinc.com
Kang Yang [Fri, 23 Feb 2024 05:45:05 +0000 (13:45 +0800)]
wifi: ath12k: add rcu lock for ath12k_wmi_p2p_noa_event()
Warning will appear when running P2P GO:
WARNING: suspicious RCU usage
drivers/net/wireless/ath/ath12k/mac.c:583 suspicious rcu_dereference_check() usage!
other info that might help us debug this:
rcu_scheduler_active = 2, debug_locks = 1
no locks held by swapper/0/0.
stack backtrace:
CPU: 0 PID: 0 Comm: swapper/0 Not tainted 6.8.0-rc4-wt-ath+ #4
Call Trace:
<IRQ>
dump_stack_lvl+0x82/0xa0
dump_stack+0x14/0x20
lockdep_rcu_suspicious+0x214/0x3b0
ath12k_mac_get_ar_by_vdev_id+0x192/0x220 [ath12k]
ath12k_wmi_op_rx+0x2d7/0x1b40 [ath12k]
ath12k_mac_get_ar_by_vdev_id() requires its callers to have called
rcu_read_lock(), but in ath12k_wmi_p2p_noa_event() it is called without
doing so, and hence the warning was triggered.
Add rcu_read_lock() and rcu_read_unlock() to avoid warning.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Fixes: 9411eecb60cb ("wifi: ath12k: implement handling of P2P NoA event")
Reported-by: Kalle Valo <quic_kvalo@quicinc.com>
Closes: https://lore.kernel.org/linux-wireless/87o7cusyvw.fsf@kernel.org/
Signed-off-by: Kang Yang <quic_kangyang@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240223054505.438839-1-quic_kangyang@quicinc.com
Baochen Qiang [Fri, 23 Feb 2024 05:31:11 +0000 (13:31 +0800)]
wifi: ath11k: decrease MHI channel buffer length to 8KB
Currently buf_len field of ath11k_mhi_config_qca6390 is assigned
with 0, making MHI use a default size, 64KB, to allocate channel
buffers. This is likely to fail in some scenarios where system
memory is highly fragmented and memory compaction or reclaim is
not allowed.
There is a fail report which is caused by it:
kworker/u32:45: page allocation failure: order:4, mode:0x40c00(GFP_NOIO|__GFP_COMP), nodemask=(null),cpuset=/,mems_allowed=0
CPU: 0 PID: 19318 Comm: kworker/u32:45 Not tainted 6.8.0-rc3-1.gae4495f-default #1 openSUSE Tumbleweed (unreleased)
493b6d5b382c603654d7a81fc3c144d59a1dfceb
Workqueue: events_unbound async_run_entry_fn
Call Trace:
<TASK>
dump_stack_lvl+0x47/0x60
warn_alloc+0x13a/0x1b0
? srso_alias_return_thunk+0x5/0xfbef5
? __alloc_pages_direct_compact+0xab/0x210
__alloc_pages_slowpath.constprop.0+0xd3e/0xda0
__alloc_pages+0x32d/0x350
? mhi_prepare_channel+0x127/0x2d0 [mhi
40df44e07c05479f7a6e7b90fba9f0e0031a7814]
__kmalloc_large_node+0x72/0x110
__kmalloc+0x37c/0x480
? mhi_map_single_no_bb+0x77/0xf0 [mhi
40df44e07c05479f7a6e7b90fba9f0e0031a7814]
? mhi_prepare_channel+0x127/0x2d0 [mhi
40df44e07c05479f7a6e7b90fba9f0e0031a7814]
mhi_prepare_channel+0x127/0x2d0 [mhi
40df44e07c05479f7a6e7b90fba9f0e0031a7814]
__mhi_prepare_for_transfer+0x44/0x80 [mhi
40df44e07c05479f7a6e7b90fba9f0e0031a7814]
? __pfx_____mhi_prepare_for_transfer+0x10/0x10 [mhi
40df44e07c05479f7a6e7b90fba9f0e0031a7814]
device_for_each_child+0x5c/0xa0
? __pfx_pci_pm_resume+0x10/0x10
ath11k_core_resume+0x65/0x100 [ath11k
a5094e22d7223135c40d93c8f5321cf09fd85e4e]
? srso_alias_return_thunk+0x5/0xfbef5
ath11k_pci_pm_resume+0x32/0x60 [ath11k_pci
830b7bfc3ea80ebef32e563cafe2cb55e9cc73ec]
? srso_alias_return_thunk+0x5/0xfbef5
dpm_run_callback+0x8c/0x1e0
device_resume+0x104/0x340
? __pfx_dpm_watchdog_handler+0x10/0x10
async_resume+0x1d/0x30
async_run_entry_fn+0x32/0x120
process_one_work+0x168/0x330
worker_thread+0x2f5/0x410
? __pfx_worker_thread+0x10/0x10
kthread+0xe8/0x120
? __pfx_kthread+0x10/0x10
ret_from_fork+0x34/0x50
? __pfx_kthread+0x10/0x10
ret_from_fork_asm+0x1b/0x30
</TASK>
Actually those buffers are used only by QMI target -> host communication.
And for WCN6855 and QCA6390, the largest packet size for that is less
than 6KB. So change buf_len field to 8KB, which results in order 1
allocation if page size is 4KB. In this way, we can at least save some
memory, and as well as decrease the possibility of allocation failure
in those scenarios.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3.6510.30
Reported-by: Vlastimil Babka <vbabka@suse.cz>
Closes: https://lore.kernel.org/ath11k/96481a45-3547-4d23-ad34-3a8f1d90c1cd@suse.cz/
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240223053111.29170-1-quic_bqiang@quicinc.com
Johannes Berg [Fri, 23 Feb 2024 09:01:46 +0000 (10:01 +0100)]
bitfield: suppress "dubious: x & !y" sparse warning
There's a somewhat common pattern of using FIELD_PREP()
even for single bits, e.g.
cmd->info1 |= FIELD_PREP(HTT_SRNG_SETUP_CMD_INFO1_RING_FLAGS_MSI_SWAP,
!!(params.flags & HAL_SRNG_FLAGS_MSI_SWAP));
which might as well be written as
if (params.flags & HAL_SRNG_FLAGS_MSI_SWAP)
cmd->info1 |= HTT_SRNG_SETUP_CMD_INFO1_RING_FLAGS_MSI_SWAP;
(since info1 is fully initialized to start with), but in
a long chain of FIELD_PREP() this really seems fine.
However, it triggers a sparse warning, in the check in
the macro for whether a constant value fits into the mask,
as this contains a "& (_val)". In this case, this really
is always intentional, so just suppress the warning by
adding "0+" to the expression, indicating explicitly that
this is correct.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240223100146.d243b6b1a9a1.I033828b1187c6bccf086e31400f7e933bb8373e7@changeid
Shiji Yang [Fri, 23 Feb 2024 13:34:32 +0000 (21:34 +0800)]
wifi: rtl8xxxu: fix mixed declarations in rtl8xxxu_set_aifs()
Moving struct ieee80211_sta *sta variable definition to the front
of the code to fix the ISO C90 forbids mixed declarations and code
warning.
Fixes: 43532c050f8e ("wifi: rtl8xxxu: support multiple interfaces in set_aifs()")
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Reviewed-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/TYAP286MB03157A408E0D69F2F6FBD88ABC552@TYAP286MB0315.JPNP286.PROD.OUTLOOK.COM
Johannes Berg [Fri, 23 Feb 2024 10:40:27 +0000 (11:40 +0100)]
wifi: zd1211rw: silence sparse warnings
This code wants to compare the obtained value, but as it also
has a special type for register addresses to find places doing
such compares and calculations wrong, we need explicit casts
here to silence sparse.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240223114023.976fcd59e97a.I0bba4ef7dc2847ce8ab5ec229149e1a09413b8b9@changeid
Johannes Berg [Fri, 23 Feb 2024 10:40:25 +0000 (11:40 +0100)]
wifi: rt2x00: silence sparse warnings
Clearly writing __le32 was intended here, so just put the
right casts into the code to silence sparse about it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240223114023.ce0c714124e9.I2b5710b761f63522574fbe7654d37151c31e0b77@changeid
Johannes Berg [Fri, 23 Feb 2024 10:40:24 +0000 (11:40 +0100)]
wifi: brcmsmac: silence sparse warnings
sparse complains on this code about casts that lose bits
due to the usage of bitwise not, but really we do want
16 bits only, so clarify that by using masks.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240223114023.06e5ade90bcd.I41a0cbae1fa259cfbf5fa117ddfce908877475a2@changeid
Johannes Berg [Fri, 23 Feb 2024 10:40:23 +0000 (11:40 +0100)]
wifi: b43: silence sparse warnings
sparse complains on this code about casts that lose bits
due to the usage of bitwise not, but really we do want
16 bits only, so clarify that by using masks.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240223114023.c64e2d348453.Iccc4ace1116721a044e5f31f40ea7709e72145f3@changeid
Kalle Valo [Tue, 27 Feb 2024 14:59:41 +0000 (16:59 +0200)]
Merge tag 'mt76-for-kvalo-2024-02-22' of https://github.com/nbd168/wireless
mt76 patches for 6.9
* fixes
* support for newer chips in the mt7915 driver
* mt7996 improvements
* page pool performance improvement
Alexey Berezhok [Thu, 22 Feb 2024 12:29:23 +0000 (15:29 +0300)]
wifi: brcmfmac: do not pass hidden SSID attribute as value directly
In brcmf_cfg80211_start_ap() do not assume that NL80211_HIDDEN_SSID_NOT_IN_USE
is zero but prefer an explicit check instead. Use local variable 'closednet'
to pass in function call and use for error message.
Compile tested only. Addition for the commit
f20073f50dfd1 ("wifi: brcmfmac: do
not cast hidden SSID attribute value to boolean").
Signed-off-by: Alexey Berezhok <a@bayrepo.ru>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240222122923.46691-1-a@bayrepo.ru
Chin-Yen Lee [Thu, 22 Feb 2024 06:42:58 +0000 (14:42 +0800)]
wifi: rtw89: pci: implement PCI CLK/ASPM/L1SS for WiFi 7 chips
PCI CLK/ASPM/L1SS is power management mechanism used to reduce power
consumption of PCI chip. The registers for setting of these features
in WiFi 7 Chip are different from WiFi 6 chip, so separate them
in generation information.
Signed-off-by: Chin-Yen Lee <timlee@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240222064258.59782-4-pkshih@realtek.com
Kuan-Chung Chen [Thu, 22 Feb 2024 06:42:57 +0000 (14:42 +0800)]
wifi: rtw89: Update EHT PHY beamforming capability
Adjust beamforming capabilities to accurately reflect the supported
EHT features by WiFi 7 chip 8922A. It includes 1) Unset EHT CQI
feedback and 16-subcarrier grouping. 2) Correct Beamformee SS value.
3) Enable partial and full bandwidth SU/MU feedback.
Signed-off-by: Kuan-Chung Chen <damon.chen@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240222064258.59782-3-pkshih@realtek.com
Kuan-Chung Chen [Thu, 22 Feb 2024 06:42:56 +0000 (14:42 +0800)]
wifi: rtw89: advertise missing extended scan feature
Add support for random serial number in probe request and
configure channel dwell time. Advertise corresponding feature flag
NL80211_EXT_FEATURE_SCAN_RANDOM_SN and NL80211_EXT_FEATURE_SET_SCAN_DWELL.
Use the scan request duration as channel dwell time when it is
non-zero, otherwise use the default value.
Signed-off-by: Kuan-Chung Chen <damon.chen@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240222064258.59782-2-pkshih@realtek.com
Gustavo A. R. Silva [Fri, 16 Feb 2024 19:27:56 +0000 (13:27 -0600)]
wifi: brcmfmac: fweh: Fix boot crash on Raspberry Pi 4
Fix boot crash on Raspberry Pi by moving the update to `event->datalen`
before data is copied into flexible-array member `data` via `memcpy()`.
Flexible-array member `data` was annotated with `__counted_by(datalen)`
in commit
62d19b358088 ("wifi: brcmfmac: fweh: Add __counted_by for
struct brcmf_fweh_queue_item and use struct_size()"). The intention of
this is to gain visibility into the size of `data` at run-time through
its _counter_ (in this case `datalen`), and with this have its accesses
bounds-checked at run-time via CONFIG_FORTIFY_SOURCE and
CONFIG_UBSAN_BOUNDS.
To effectively accomplish the above, we shall update the counter
(`datalen`), before the first access to the flexible array (`data`),
which was also done in the mentioned commit.
However, commit
edec42821911 ("wifi: brcmfmac: allow per-vendor event
handling") inadvertently caused a buffer overflow, detected by
FORTIFY_SOURCE. It moved the `event->datalen = datalen;` update to after
the first `data` access, at which point `event->datalen` was not yet
updated from zero (after calling `kzalloc()`), leading to the overflow
issue.
This fix repositions the `event->datalen = datalen;` update before
accessing `data`, restoring the intended buffer overflow protection. :)
Fixes: edec42821911 ("wifi: brcmfmac: allow per-vendor event handling")
Reported-by: Nathan Chancellor <nathan@kernel.org>
Closes: https://gist.github.com/nathanchance/e22f681f3bfc467f15cdf6605021aaa6
Tested-by: Nathan Chancellor <nathan@kernel.org>
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Reviewed-by: Kees Cook <keescook@chromium.org>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/Zc+3PFCUvLoVlpg8@neat
Jeff Johnson [Fri, 23 Feb 2024 15:20:34 +0000 (17:20 +0200)]
dt-bindings: net: wireless: qcom: Update maintainers
Add Jeff Johnson as a maintainer of the qcom,ath1*k.yaml files.
Signed-off-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240217-ath1xk-maintainer-v1-1-9f7ff5fb6bf4@quicinc.com
Kalle Valo [Fri, 23 Feb 2024 15:20:33 +0000 (17:20 +0200)]
wifi: ath11k: thermal: don't try to register multiple times
Every time the firmware boots we call ath11k_core_qmi_firmware_ready() which
ends up calling ath11k_thermal_register(). So we try to register thermal
devices multiple times. And when we power off the firmware during
suspend/hibernation (implemented in the next patch) we get a warning in resume:
hwmon hwmon4: PM: parent phy0 should not be sleeping
Workaround this similarly like ath11k_mac_register() does by testing
ATH11K_FLAG_REGISTERED.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3.6510.30
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Link: https://msgid.link/20240221024725.10057-6-quic_bqiang@quicinc.com
Baochen Qiang [Fri, 23 Feb 2024 15:20:33 +0000 (17:20 +0200)]
wifi: ath11k: fix warning on DMA ring capabilities event
We are seeing below warning in both reset and suspend/resume scenarios:
[69663.691847] ath11k_pci 0000:02:00.0: Already processed, so ignoring dma ring caps
This is because ab->num_db_cap is not cleared in
ath11k_wmi_free_dbring_caps(), so clear it to avoid such
warnings.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3.6510.30
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Link: https://msgid.link/20240221024725.10057-5-quic_bqiang@quicinc.com
Baochen Qiang [Fri, 23 Feb 2024 15:20:33 +0000 (17:20 +0200)]
wifi: ath11k: do not dump SRNG statistics during resume
Both the firmware reset feature and the power management
suspend/resume feature share common power-down and power-up
functionality. One aspect of the power-up functionality is
the handling of the ATH11K_QMI_EVENT_FW_INIT_DONE event.
When this event is received, a call is made to
ath11k_hal_dump_srng_stats(), with the purpose to collect
information that may be useful in debugging the cause of a
firmware reset.
Unfortunately, since this functionality is shared between
both the firmware reset path and the power management
resume path, the kernel log is flooded with messages during
resume. Since these messages are not useful during resume,
and in fact can be confusing and can increase the time it
takes to resume, update the logic to only call
ath11k_hal_dump_srng_stats() during firmware reset.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3.6510.30
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Link: https://msgid.link/20240221024725.10057-4-quic_bqiang@quicinc.com
Baochen Qiang [Fri, 23 Feb 2024 15:20:33 +0000 (17:20 +0200)]
wifi: ath11k: remove MHI LOOPBACK channels
There is no driver to match these two channels, so
remove them. This fixes warnings from MHI subsystem during suspend:
mhi mhi0_LOOPBACK: 1: Failed to reset channel, still resetting
mhi mhi0_LOOPBACK: 0: Failed to reset channel, still resetting
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3.6510.30
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Link: https://msgid.link/20240221024725.10057-3-quic_bqiang@quicinc.com
Baochen Qiang [Fri, 23 Feb 2024 15:20:32 +0000 (17:20 +0200)]
wifi: ath11k: rearrange IRQ enable/disable in reset path
For non WoW suspend/resume, ath11k host powers down whole hardware
when suspend and powers up it when resume, the code path it goes
through is very like the ath11k reset logic.
In order to reuse that logic, rearrange IRQ handling in the reset
path.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3.6510.30
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Link: https://msgid.link/20240221024725.10057-2-quic_bqiang@quicinc.com
Praveen Kumar Kannoju [Wed, 21 Feb 2024 08:27:52 +0000 (13:57 +0530)]
bonding: rate-limit bonding driver inspect messages
Through the routine bond_mii_monitor(), bonding driver inspects and commits
the slave state changes. During the times when slave state change and
failure in aqcuiring rtnl lock happen at the same time, the routine
bond_mii_monitor() reschedules itself to come around after 1 msec to commit
the new state.
During this, it executes the routine bond_miimon_inspect() to re-inspect
the state chane and prints the corresponding slave state on to the console.
Hence we do see a message at every 1 msec till the rtnl lock is acquired
and state chage is committed.
This patch doesn't change how bond functions. It only simply limits this
kind of log flood.
Signed-off-by: Praveen Kumar Kannoju <praveen.kannoju@oracle.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: Hangbin Liu <liuhangbin@gmail.com>
Acked-by: Jay Vosburgh <jay.vosburgh@canonical.com>
Link: https://lore.kernel.org/r/20240221082752.4660-1-praveen.kannoju@oracle.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Jakub Kicinski [Fri, 23 Feb 2024 03:06:20 +0000 (19:06 -0800)]
Merge tag 'nf-next-24-02-21' of https://git./linux/kernel/git/netfilter/nf-next
Florian Westphal says:
====================
netfilter updates for net-next
1. Prefer KMEM_CACHE() macro to create kmem caches, from Kunwu Chan.
Patches 2 and 3 consolidate nf_log NULL checks and introduces
extra boundary checks on family and type to make it clear that no out
of bounds access will happen. No in-tree user currently passes such
values, but thats not clear from looking at the function.
From Pablo Neira Ayuso.
Patch 4, also from Pablo, gets rid of unneeded conditional in
nft_osf init function.
Patch 5, from myself, fixes erroneous Kconfig dependencies that
came in an earlier net-next pull request. This should get rid
of the xtables related build failure reports.
Patches 6 to 10 are an update to nftables' concatenated-ranges
set type to speed up element insertions. This series also
compacts a few data structures and cleans up a few oddities such
as reliance on ZERO_SIZE_PTR when asking to allocate a set with
no elements. From myself.
Patches 11 moves the nf_reinject function from the netfilter core
(vmlinux) into the nfnetlink_queue backend, the only location where
this is called from. Also from myself.
Patch 12, from Kees Cook, switches xtables' compat layer to use
unsafe_memcpy because xt_entry_target cannot easily get converted
to a real flexible array (its UAPI and used inside other structs).
* tag 'nf-next-24-02-21' of https://git.kernel.org/pub/scm/linux/kernel/git/netfilter/nf-next:
netfilter: x_tables: Use unsafe_memcpy() for 0-sized destination
netfilter: move nf_reinject into nfnetlink_queue modules
netfilter: nft_set_pipapo: use GFP_KERNEL for insertions
netfilter: nft_set_pipapo: speed up bulk element insertions
netfilter: nft_set_pipapo: shrink data structures
netfilter: nft_set_pipapo: do not rely on ZERO_SIZE_PTR
netfilter: nft_set_pipapo: constify lookup fn args where possible
netfilter: xtables: fix up kconfig dependencies
netfilter: nft_osf: simplify init path
netfilter: nf_log: validate nf_logger_find_get()
netfilter: nf_log: consolidate check for NULL logger in lookup function
netfilter: expect: Simplify the allocation of slab caches in nf_conntrack_expect_init
====================
Link: https://lore.kernel.org/r/20240221112637.5396-1-fw@strlen.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Breno Leitao [Wed, 21 Feb 2024 16:17:32 +0000 (08:17 -0800)]
ipv6/sit: Do not allocate stats in the driver
With commit
34d21de99cea9 ("net: Move {l,t,d}stats allocation to core and
convert veth & vrf"), stats allocation could be done on net core
instead of this driver.
With this new approach, the driver doesn't have to bother with error
handling (allocation failure checking, making sure free happens in the
right spot, etc). This is core responsibility now.
Remove the allocation in the ipv6/sit driver and leverage the network
core allocation.
Signed-off-by: Breno Leitao <leitao@debian.org>
Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: David Ahern <dsahern@kernel.org>
Link: https://lore.kernel.org/r/20240221161732.3026127-1-leitao@debian.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Geert Uytterhoeven [Wed, 21 Feb 2024 10:52:41 +0000 (11:52 +0100)]
octeon_ep_vf: Improve help text grammar
Add missing articles.
Fix plural vs. singular.
Fix present vs. future.
Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: Sathesh B Edara <sedara@marvell.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/b3b97462c3d9eba2ec03dd6d597e63bf49a7365a.1708512706.git.geert+renesas@glider.be
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Colin Ian King [Tue, 20 Feb 2024 09:17:37 +0000 (09:17 +0000)]
net: microchip: lan743x: Fix spelling mistake "erro" -> "error"
There is a spelling mistake in a netif_err message. Fix it.
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/20240220091737.2676984-1-colin.i.king@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Alexander Gordeev [Thu, 15 Feb 2024 08:05:00 +0000 (09:05 +0100)]
net/af_iucv: fix virtual vs physical address confusion
Fix virtual vs physical address confusion. This does not fix a bug
since virtual and physical address spaces are currently the same.
Signed-off-by: Alexander Gordeev <agordeev@linux.ibm.com>
Reviewed-by: Alexandra Winter <wintera@linux.ibm.com>
Link: https://lore.kernel.org/r/20240215080500.2616848-1-agordeev@linux.ibm.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Jakub Kicinski [Thu, 22 Feb 2024 23:24:56 +0000 (15:24 -0800)]
Merge git://git./linux/kernel/git/netdev/net
Cross-merge networking fixes after downstream PR.
Conflicts:
net/ipv4/udp.c
f796feabb9f5 ("udp: add local "peek offset enabled" flag")
56667da7399e ("net: implement lockless setsockopt(SO_PEEK_OFF)")
Adjacent changes:
net/unix/garbage.c
aa82ac51d633 ("af_unix: Drop oob_skb ref before purging queue in GC.")
11498715f266 ("af_unix: Remove io_uring code for GC.")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Jakub Kicinski [Thu, 22 Feb 2024 23:11:18 +0000 (15:11 -0800)]
Merge tag 'wireless-next-2024-02-22' of git://git./linux/kernel/git/wireless/wireless-next
Kalle Valo says:
====================
wireless-next patches for v6.9
The third "new features" pull request for v6.9. This is a quick
followup to send commit
04edb5dc68f4 ("wifi: ath12k: Fix uninitialized
use of ret in ath12k_mac_allocate()") to fix the ath12k clang warning
introduced in the previous pull request.
We also have support for QCA2066 in ath11k, several new features in
ath12k and few other changes in drivers. In stack it's mostly cleanup
and refactoring.
Major changes:
ath12k
* firmware-2.bin support
* support having multiple identical PCI devices (firmware needs to
have ATH12K_FW_FEATURE_MULTI_QRTR_ID)
* QCN9274: support split-PHY devices
* WCN7850: enable Power Save Mode in station mode
* WCN7850: P2P support
ath11k:
* QCA6390 & WCN6855: support 2 concurrent station interfaces
* QCA2066 support
iwlwifi
* mvm: support wider-bandwidth OFDMA
* bump firmware API to 90 for BZ/SC devices
brcmfmac
* DMI nvram filename quirk for ACEPC W5 Pro
* tag 'wireless-next-2024-02-22' of git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next: (75 commits)
wifi: wilc1000: revert reset line logic flip
wifi: brcmfmac: Add DMI nvram filename quirk for ACEPC W5 Pro
wifi: rtlwifi: set initial values for unexpected cases of USB endpoint priority
wifi: rtl8xxxu: check vif before using in rtl8xxxu_tx()
wifi: rtlwifi: rtl8192cu: Fix TX aggregation
wifi: wilc1000: remove AKM suite be32 conversion for external auth request
wifi: nl80211: refactor parsing CSA offsets
wifi: nl80211: force WLAN_AKM_SUITE_SAE in big endian in NL80211_CMD_EXTERNAL_AUTH
wifi: iwlwifi: load b0 version of ucode for HR1/HR2
wifi: iwlwifi: handle per-phy statistics from fw
wifi: iwlwifi: iwl-fh.h: fix kernel-doc issues
wifi: iwlwifi: api: fix kernel-doc reference
wifi: iwlwifi: mvm: unlock mvm if there is no primary link
wifi: iwlwifi: bump FW API to 90 for BZ/SC devices
wifi: iwlwifi: mvm: support PHY context version 6
wifi: iwlwifi: mvm: partially support PHY context version 6
wifi: iwlwifi: mvm: support wider-bandwidth OFDMA
wifi: cfg80211: use ML element parsing helpers
wifi: mac80211: align ieee80211_mle_get_bss_param_ch_cnt()
wifi: cfg80211: refactor RNR parsing
...
====================
Link: https://lore.kernel.org/r/20240222105205.CEC54C433F1@smtp.kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Linus Torvalds [Thu, 22 Feb 2024 17:57:58 +0000 (09:57 -0800)]
Merge tag 'net-6.8.0-rc6' of git://git./linux/kernel/git/netdev/net
Pull networking fixes from Paolo Abeni:
"Including fixes from bpf and netfilter.
Current release - regressions:
- af_unix: fix another unix GC hangup
Previous releases - regressions:
- core: fix a possible AF_UNIX deadlock
- bpf: fix NULL pointer dereference in sk_psock_verdict_data_ready()
- netfilter: nft_flow_offload: release dst in case direct xmit path
is used
- bridge: switchdev: ensure MDB events are delivered exactly once
- l2tp: pass correct message length to ip6_append_data
- dccp/tcp: unhash sk from ehash for tb2 alloc failure after
check_estalblished()
- tls: fixes for record type handling with PEEK
- devlink: fix possible use-after-free and memory leaks in
devlink_init()
Previous releases - always broken:
- bpf: fix an oops when attempting to read the vsyscall page through
bpf_probe_read_kernel
- sched: act_mirred: use the backlog for mirred ingress
- netfilter: nft_flow_offload: fix dst refcount underflow
- ipv6: sr: fix possible use-after-free and null-ptr-deref
- mptcp: fix several data races
- phonet: take correct lock to peek at the RX queue
Misc:
- handful of fixes and reliability improvements for selftests"
* tag 'net-6.8.0-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (72 commits)
l2tp: pass correct message length to ip6_append_data
net: phy: realtek: Fix rtl8211f_config_init() for RTL8211F(D)(I)-VD-CG PHY
selftests: ioam: refactoring to align with the fix
Fix write to cloned skb in ipv6_hop_ioam()
phonet/pep: fix racy skb_queue_empty() use
phonet: take correct lock to peek at the RX queue
net: sparx5: Add spinlock for frame transmission from CPU
net/sched: flower: Add lock protection when remove filter handle
devlink: fix port dump cmd type
net: stmmac: Fix EST offset for dwmac 5.10
tools: ynl: don't leak mcast_groups on init error
tools: ynl: make sure we always pass yarg to mnl_cb_run
net: mctp: put sock on tag allocation failure
netfilter: nf_tables: use kzalloc for hook allocation
netfilter: nf_tables: register hooks last when adding new chain/flowtable
netfilter: nft_flow_offload: release dst in case direct xmit path is used
netfilter: nft_flow_offload: reset dst in route object after setting up flow
netfilter: nf_tables: set dormant flag on hook register failure
selftests: tls: add test for peeking past a record of a different type
selftests: tls: add test for merging of same-type control messages
...
Linus Torvalds [Thu, 22 Feb 2024 17:23:22 +0000 (09:23 -0800)]
Merge tag 'trace-v6.8-rc5' of git://git./linux/kernel/git/trace/linux-trace
Pull tracing fix from Steven Rostedt:
- While working on the ring buffer I noticed that the counter used for
knowing where the end of the data is on a sub-buffer was not a full
"int" but just 20 bits. It was masked out to 0xfffff.
With the new code that allows the user to change the size of the
sub-buffer, it is theoretically possible to ask for a size bigger
than 2^20. If that happens, unexpected results may occur as there's
no code checking if the counter overflowed the 20 bits of the write
mask. There are other checks to make sure events fit in the
sub-buffer, but if the sub-buffer itself is too big, that is not
checked.
Add a check in the resize of the sub-buffer to make sure that it
never goes beyond the size of the counter that holds how much data is
on it.
* tag 'trace-v6.8-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/trace/linux-trace:
ring-buffer: Do not let subbuf be bigger than write mask
Paolo Abeni [Thu, 22 Feb 2024 14:31:25 +0000 (15:31 +0100)]
Merge branch 'bnxt_en-ntuple-filter-improvements'
Michael Chan says:
====================
bnxt_en: Ntuple filter improvements
The current Ntuple filter implementation has a limitation on 5750X (P5)
and newer chips. The destination ring of the ntuple filter must be
a valid ring in the RSS indirection table. Ntuple filters may not work
if the RSS indirection table is modified by the user to only contain a
subset of the rings. If an ntuple filter is set to a ring destination
that is not in the RSS indirection table, the packet matching that
filter will be placed in a random ring instead of the specified
destination ring.
This series of patches will fix the problem by using a separate VNIC
for ntuple filters. The default VNIC will be dedicated for RSS and
so the indirection table can be setup in any way and will not affect
ntuple filters using the separate VNIC.
Quite a bit of refactoring is needed to do the the VNIC and RSS
context accounting in the first few patches. This is technically a
bug fix, but I think the changes are too big for -net.
====================
Link: https://lore.kernel.org/r/20240220230317.96341-1-michael.chan@broadcom.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Pavan Chebbi [Tue, 20 Feb 2024 23:03:17 +0000 (15:03 -0800)]
bnxt_en: Use the new VNIC to create ntuple filters
The newly created vnic (BNXT_VNIC_NTUPLE) is ready to be used to create
ntuple filters when supported by firmware. All RX rings can be used
regardless of the RSS indirection setting on the default VNIC.
Reviewed-by: Somnath Kotur <somnath.kotur@broadcom.com>
Reviewed-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Signed-off-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Pavan Chebbi [Tue, 20 Feb 2024 23:03:16 +0000 (15:03 -0800)]
bnxt_en: Create and setup the additional VNIC for adding ntuple filters
Allocate and setup the additional VNIC for ntuple filters if this
new method is supported by the firmware. Even though this VNIC is
only used for ntuple filters with direct ring destinations, we still
setup the RSS hash to be identical to the default VNIC so that each
RX packet will have the correct hash in the RX completion. This
VNIC is always at VNIC index BNXT_VNIC_NTUPLE.
Reviewed-by: Somnath Kotur <somnath.kotur@broadcom.com>
Signed-off-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Pavan Chebbi [Tue, 20 Feb 2024 23:03:15 +0000 (15:03 -0800)]
bnxt_en: Provision for an additional VNIC for ntuple filters
On newer chips that support the ring table index method for
ntuple filters, the current scheme of using the same VNIC for
both RSS and ntuple filters will not work in all cases. An
ntuple filter can only be directed to a destination ring if
that destination ring is also in the RSS indirection table.
To support ntuple filters with any arbitratry RSS indirection
table that may only include a subset of the rings, we need to
use a separate VNIC for ntuple filters.
This patch provisions the additional VNIC. The next patch will
allocate additional VNIC from firmware and set it up.
Reviewed-by: Somnath Kotur <somnath.kotur@broadcom.com>
Reviewed-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Signed-off-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Pavan Chebbi [Tue, 20 Feb 2024 23:03:14 +0000 (15:03 -0800)]
bnxt_en: Define BNXT_VNIC_DEFAULT for the default vnic index
Replace hard coded 0 index with more meaningful BNXT_VNIC_DEFAULT.
Reviewed-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Reviewed-by: Somnath Kotur <somnath.kotur@broadcom.com>
Signed-off-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Pavan Chebbi [Tue, 20 Feb 2024 23:03:13 +0000 (15:03 -0800)]
bnxt_en: Refactor bnxt_set_features()
Refactor bnxt_set_features() function to have a common
function to re-init. We'll need this to reinitialize when
ntuple configuration changes.
Reviewed-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Reviewed-by: Andy Gospodarek <andrew.gospodarek@broadcom.com>
Signed-off-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Venkat Duvvuru [Tue, 20 Feb 2024 23:03:12 +0000 (15:03 -0800)]
bnxt_en: Add bnxt_get_total_vnics() to calculate number of VNICs
Refactor the code by adding a new function to calculate the number of
required VNICs. This is used in multiple places when reserving or
checking resources.
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Venkat Duvvuru <venkatkumar.duvvuru@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Michael Chan [Tue, 20 Feb 2024 23:03:11 +0000 (15:03 -0800)]
bnxt_en: Check additional resources in bnxt_check_rings()
bnxt_check_rings() is called to check if we have enough resource
assets to satisfy the new number of ethtool channels. If the asset
test fails, the ethtool operation will fail gracefully. Otherwise
we will proceed and commit to use the new number of channels. If it
fails to allocate any resources, the chip will fail to come up.
For completeness, check all possible resources before committing to
the new settings. Add the missing ring group and RSS context asset
tests in bnxt_check_rings().
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Reviewed-by: Somnath Kotur <somnath.kotur@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
projects / linux.git / log