media: ov5640: Split DVP and CSI-2 formats

The format enumeration list is shared between CSI-2 and DVP modes.
This lead to the enumeration of unsupported format variants in both
modes.

Separate the list of DVP and CSI-2 formats and create helpers to access
the correct one.

Signed-off-by: Jacopo Mondi <jacopo@jmondi.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>

media: ov5640: Adjust format to bpp in s_fmt

The ov5640 driver supports different sizes for different mbus_codes.
In particular:

- 8bpp modes: high resolution sizes (>= 1280x720)
- 16bpp modes: all sizes
- 24bpp modes: low resolutions sizes (< 1280x720)

Adjust the image sizes according to the above constraints.

Signed-off-by: Jacopo Mondi <jacopo@jmondi.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>

media: ov5640: Restrict sizes to mbus code

The ov5640 driver supports different sizes for different mbus_codes.
In particular:

- 8bpp modes: high resolution sizes (>= 1280x720)
- 16bpp modes: all sizes
- 24bpp modes: low resolutions sizes (< 1280x720)

Restrict the frame sizes enumerations to the above constraints.

While at it, make sure the fse->mbus_code parameter is valid, and return
-EINVAL if it's not.

Signed-off-by: Jacopo Mondi <jacopo@jmondi.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>

media: ov5640: Add BGR888 format

Add support for BGR888 image format.

No existing media bus codes describe exactly the way data is transferred
on the CSI-2 bus. This is not a new issue, the CSI-2 YUV422 8-bit format
is described by MEDIA_BUS_FMT_UYVY8_1X16 which is an arbitrary
convention and not an exact match. Use the MEDIA_BUS_FMT_BGR888_1X24 to
follow the same convention, based on the order in which bits are
transmitted over the CSI-2 bus when producing images in RGB24 format.

Signed-off-by: Jacopo Mondi <jacopo@jmondi.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>

media: ov5640: Add RGB565_1X16 format

The driver already supports the 2X8_[LE|BE] variants of RGB565
formats.

As for CSI-2 the 2X8 variants do not apply, add RGB565_1X16 variant
with little-endian ordering of components as required by the CSI-2
specifications.

Signed-off-by: Jacopo Mondi <jacopo@jmondi.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>

media: ov5640: Register device properties

Parse the device properties and register the rotation and orientation
V4L2 controls using v4l2_ctrl_new_fwnode_properties().

Remove the open-coded parsing of the rotation property and assume the
DTS is correct is providing either <0> or <180> as possible rotations.

Signed-off-by: Jacopo Mondi <jacopo@jmondi.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>

media: ov5640: Implement get_selection

Implement the get_selection pad operation for the OV5640 sensor driver.

The supported targets report the sensor's native size, the active pixel
array size and the analog crop rectangle from which the image is
produced.

Signed-off-by: Jacopo Mondi <jacopo@jmondi.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>

media: ov5640: Implement init_cfg

Implement the init_cfg pad operation to initialize the subdev state
format to the default one.

Signed-off-by: Jacopo Mondi <jacopo@jmondi.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>

media: ov5640: Change CSI-2 timings to comply with FPS

Now that the frame duration can be controlled by tuning the VBLANK
duration in CSI-2 mode, fix all modes definitions to comply with the
reported FPS.

All modes run at 30 FPS except for full-resolution mode 2592x1944
which runs at 15FPS.

Tested on a 2 data lanes setup in UYVY and RGB565 modes in CSI-2 mode.

Signed-off-by: Jacopo Mondi <jacopo@jmondi.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>

media: ov5640: Remove frame rate check from find_mode()

The current implementation of ov5640_find_mode() fails if the
frame rate programmed with s_frame_interval doesn't match the
maximum frame rate for the current mode.

This causes issues when moving from one mode with higher FPS to another
one which only supports a lower FPS range with tools like media-ctl.

It also forces users that do not use s_frame_interval(), but rather
configure blankings explicitly, to adjust the programmed FPS range to
avoid failures.

For this reason, remove the FPS check from ov5640_find_mode() and only
perform it at s_frame_interval() time.

Signed-off-by: Jacopo Mondi <jacopo@jmondi.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>

media: ov5640: Adjust vblank with s_frame_interval

Adjust the vertical blanking when s_frame_interval is used.

s_frame_interval allows to set a fixed frame rate, which gets stored as
the sensor's current one. When a new mode is applied, the current frame
rate is reset to the mode's default one. In order to correctly report
the currently configured vertical blanking for s_frame_interval users,
verify that the desired frame rate has not been changed. If that's the
case, compute the correct blanking value and reflect it through the
corresponding v4l2 control.

Signed-off-by: Hugues Fruchet <hugues.fruchet@st.com>
Signed-off-by: Jacopo Mondi <jacopo@jmondi.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>

media: ov5640: Add VBLANK control

Add the VBLANK control which allows to select the duration of the
frame vertical blankings and allows to control the framerate.

The VBLANK control also modifies the exposure time range, which cannot
exceed the maximum frame length.

Signed-off-by: Jacopo Mondi <jacopo@jmondi.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>

media: ov5640: Add HBLANK control

Add the HBLANK control as read-only.

The hblank value is fixed in the mode definition and is updated
everytime a new format is applied.

Signed-off-by: Jacopo Mondi <jacopo@jmondi.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>

media: ov5640: Remove ov5640_mode_init_data

The ov5640_mode_init_data is a fictional sensor more which is used to
program the initial sensor settings.

It is only used to initialize the sensor and can be replaced
it with a throw-away mode which just wraps the register table.

Also rename the register table to drop the format from the name to make
it clear an actual sensor mode has to be applied after the initial
programming.

Signed-off-by: Jacopo Mondi <jacopo@jmondi.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>

media: ov5640: Remove duplicated mode settings

The register tables for all resolutions smaller than 720p are now
identical.

Remove the duplicated ones and create a single ov5640_setting_low_res[]
register table.

Signed-off-by: Jacopo Mondi <jacopo@jmondi.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>

media: ov5640: Re-sort per-mode register tables

The per-mode register tables are not sorted by size. Fix it.

Cosmetic change only.

Signed-off-by: Jacopo Mondi <jacopo@jmondi.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>

media: ov5640: Provide timings accessor

Provide a function to shortcut access to the correct timings definition
to avoid repeating the same pattern when accessing the sensor timings.

Signed-off-by: Jacopo Mondi <jacopo@jmondi.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>

media: ov5640: Split DVP and CSI-2 timings

Separate the timings for the DVP mode from the timings for the CSI-2
mode in the ov5640 modes definition.

The CSI-2 timings will deviate from the DVP ones as the clock tree is
calculated differently.

In CSI-2 mode change the analog crop rectangles as the OV5640 pixel
array is composed as:
- vertically: 16 dummy columns, 2592 valid ones and 16 dummy columns for
  a total of 2624 columns
- horizontally: 8 optical black lines, 6 dummy ones, 1944 valid and 6
  dummies for a total of 1964 lines

Adjust the analog crop rectangle in CSI-2 mode to:
- Skip the first 16 dummy columns
- Skip the first 14 black/dummy lines
- Pass the whole valid pixel array size to the ISP for all modes except
  1024x768, 720p and 1080p which are obtained by cropping the valid pixel
  array.

Tested in RGB565, UYVY and RGB888 modes in CSI-2 mode.

Signed-off-by: Jacopo Mondi <jacopo@jmondi.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>

media: ov5640: Fix 720x480 in RGB888 mode

Adjust the left crop of 720x480 to enable capture in RGB888 format,
which is otherwise broken.

The 56 pixels alignment has been copied from the 720x576 mode.

Signed-off-by: Jacopo Mondi <jacopo@jmondi.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>

media: ov5640: Rework timings programming

The current definition of a sensor mode defines timings as follows:

- hact, vact: Visible width and height
- htot, vtot: Total sizes including blankings

This makes difficult to clearly separate the visible sizes from the
blankings and to make the vertical blanking programmable.

Rework the sensor modes sizes definition to:
- Report the analog crop sizes
- Report the visible crop size
- Report the total pixels per line as HBLANK is fixed
- Report the VBLANK value to make it programmable

Also modify the ov5640_set_timings() function to program all the
windowing registers are remove them from the per-mode register-value
tables.

Do not change the timing values from the ones reported in the register
tables to maintain bisectability.

Signed-off-by: Jacopo Mondi <jacopo@jmondi.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>

media: ov5640: Rework CSI-2 clock tree

Re-work the ov5640_set_mipi_pclk() function to calculate the
PLL configuration using the pixel_rate and link_freq values set at
s_fmt time.

Rework the DVP clock mode settings to calculate the pixel clock
internally and remove the assumption on the 16bpp format.

Tested in MIPI CSI-2 mode with 1 and 2 data lanes with:
- all the sensor supported resolutions in UYVY, RGB565 and MJPEG formats.
- resolutions >= 1280x720 in RAW Bayer format.
- resolutions < 1280x720 in RGB888 format.

[Rework pclk_period and link_freq computation]

Signed-off-by: Jacopo Mondi <jacopo@jmondi.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hugues Fruchet <hugues.fruchet@st.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>

media: ov5640: Update pixel_rate and link_freq

After having set a new format re-calculate the pixel_rate and link_freq
control values and update them when in MIPI mode.

Take into account the limitation of the link frequency having to be
strictly smaller than 1GHz when computing the desired link_freq, and
adjust the resulting pixel_rate acounting for the clock tree
configuration.

[Adjust link_freq calculation]

Signed-off-by: Jacopo Mondi <jacopo@jmondi.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hugues Fruchet <hugues.fruchet@st.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>

media: ov5640: Add LINK_FREQ control

Add the V4L2_CID_LINK_FREQ control to the ov5640 driver.
Make the control read-only for the moment.

Signed-off-by: Jacopo Mondi <jacopo@jmondi.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>

media: ov5640: Associate bpp with formats

Associate the bit depth to each format supported by the sensor.

The bpp will be used to calculate the line length.

Signed-off-by: Jacopo Mondi <jacopo@jmondi.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>

media: ov5640: Add ov5640_is_csi2() function

Checking if the sensor is used in DVP or MIPI CSI-2 mode is a repeated
pattern which is about to be repeated more often.

Provide an inline function to shortcut that.

Signed-off-by: Jacopo Mondi <jacopo@jmondi.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>

media: ov5604: Re-arrange modes definition

The array of supported modes is close to unreadable.
Re-arrange it giving it some room to breath.

Cosmetic change only.

Signed-off-by: Jacopo Mondi <jacopo@jmondi.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>

media: ov5640: Add pixel rate to modes

Add to each mode supported by the sensor the ideal pixel rate, as
defined by Table 2.1 in the chip manual.

The ideal pixel rate will be used to compute the MIPI CSI-2 clock tree.

Signed-off-by: Jacopo Mondi <jacopo@jmondi.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Tested-by: Adam Ford <aford173@gmail.com> #imx8mm-beacon-kit
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>

media: stm32-dcmi: add support of 1X16 serial pixel formats variant

Add support of 1X16 serial pixel formats in order to support
CSI-2 camera sensor exposing 1x16 pixel formats only.

Signed-off-by: Hugues Fruchet <hugues.fruchet@st.com>
Reviewed-by: Jacopo Mondi <jacopo@jmondi.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>

media: st-mipid02: expose 1X16 serial pixel format

Expose RGB & YUV 1X16 serial pixel format variants to comply
with CSI-2 camera sensor pixel formats.

Signed-off-by: Hugues Fruchet <hugues.fruchet@foss.st.com>
Reviewed-by: Benjamin Mugnier <benjamin.mugnier@foss.st.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>

media: st-mipid02: add support for YVYU and VYUY formats

Those two formats were missing in the list of supported MBUS
formats.

Signed-off-by: Alain Volmat <alain.volmat@foss.st.com>
Reviewed-by: Benjamin Mugnier <benjamin.mugnier@foss.st.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>

media: st-mipid02: add support of pixel clock polarity

Add support of pixel clock polarity.

Signed-off-by: Hugues Fruchet <hugues.fruchet@foss.st.com>
Reviewed-by: Benjamin Mugnier <benjamin.mugnier@foss.st.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>

media: ov7251: Fix multiple problems in s_stream callback

The s_stream callback had several issues:

- If pm_runtime_get_sync() fails, the usage_count is not put.

- The sensor wasn't suspended if s_stream(subdev, 1) failed.

Fix this.

Fixes: ("media: i2c: Add pm_runtime support to ov7251")
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>

media: sunxi: Add support for the A83T MIPI CSI-2 controller

The A83T supports MIPI CSI-2 with a composite controller, covering
both the protocol logic and the D-PHY implementation. This controller
seems to be found on the A83T only and probably was abandoned since.

This implementation splits the protocol and D-PHY registers and
uses the PHY framework internally. The D-PHY is not registered as a
standalone PHY driver since it cannot be used with any other
controller.

There are a few notable points about the controller:
- The initialisation sequence involes writing specific magic init
  values that do not seem to make any particular sense given the
  concerned register fields;
- Interrupts appear to be hitting regardless of the interrupt mask
  registers, which can cause a serious flood when transmission errors
  occur.

Only 8-bit and 10-bit Bayer formats are currently supported.
While up to 4 internal channels to the CSI controller exist, only one
is currently supported by this implementation.

This work is based on the first version of the driver submitted by
Kévin L'hôpital, which was adapted to mainline from the Allwinner BSP.
This version integrates MIPI CSI-2 support as a standalone V4L2 subdev
instead of merging it in the sun6i-csi driver.

It was tested on a Banana Pi M3 board with an OV8865 sensor in a 4-lane
configuration.

Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Acked-by: Maxime Ripard <mripard@kernel.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>

media: dt-bindings: media: Add Allwinner A83T MIPI CSI-2 bindings documentation

This introduces YAML bindings documentation for the Allwinner A83T
MIPI CSI-2 controller.

Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>

media: MAINTAINERS: Add entry for the Allwinner A31 MIPI CSI-2 bridge driver

Add myself as maintainer of the Allwinner A31 MIPI CSI-2 bridge media
driver.

Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Acked-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>

media: sunxi: Add support for the A31 MIPI CSI-2 controller

The A31 MIPI CSI-2 controller is a dedicated MIPI CSI-2 bridge
found on Allwinner SoCs such as the A31 and V3/V3s.

It is a standalone block, connected to the CSI controller on one side
and to the MIPI D-PHY block on the other. It has a dedicated address
space, interrupt line and clock.

It is represented as a V4L2 subdev to the CSI controller and takes a
MIPI CSI-2 sensor as its own subdev, all using the fwnode graph and
media controller API.

Only 8-bit and 10-bit Bayer formats are currently supported.
While up to 4 internal channels to the CSI controller exist, only one
is currently supported by this implementation.

Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Acked-by: Maxime Ripard <mripard@kernel.org>
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>

media: dt-bindings: media: Add Allwinner A31 MIPI CSI-2 bindings documentation

This introduces YAML bindings documentation for the Allwinner A31 MIPI
CSI-2 controller.

Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Reviewed-by: Maxime Ripard <mripard@kernel.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>

media: dt-bindings: media: sun6i-a31-csi: Add MIPI CSI-2 input port

The A31 CSI controller supports two distinct input interfaces:
parallel and an external MIPI CSI-2 bridge. The parallel interface
is often connected to a set of hardware pins while the MIPI CSI-2
bridge is an internal FIFO-ish link. As a result, these two inputs
are distinguished as two different ports.

Note that only one of the two may be present on a controller instance.
For example, the V3s has one controller dedicated to MIPI-CSI2 and one
dedicated to parallel.

Update the binding with an explicit ports node that holds two distinct
port nodes: one for parallel input and one for MIPI CSI-2.

This is backward-compatible with the single-port approach that was
previously taken for representing the parallel interface port, which
stays enumerated as fwnode port 0.

Note that additional ports may be added in the future, especially to
support feeding the CSI controller's output to the ISP.

Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Maxime Ripard <mripard@kernel.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>

media: hantro: Add support for RK356x encoder

The RK3566 and RK3568 SoCs come with a small Hantro instance which is
solely dedicated to encoding. This patch adds the necessary structs to
the Hantro driver to allow the JPEG encoder of it to function.

Through some sleuthing through the vendor's MPP source code and after
closer inspection of the TRM, it was determined that the hardware likely
supports VP8 and H.264 as well.

Tested with the following GStreamer command:

gst-launch-1.0 videotestsrc ! v4l2jpegenc ! matroskamux ! \
               filesink location=foo.mkv

Signed-off-by: Nicolas Frattaroli <frattaroli.nicolas@gmail.com>
Reviewed-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>

media: dt-binding: media: Add rk3568-vepu binding

The RK3568 and RK3566 have a Hantro VPU node solely dedicated to
encoding. This patch adds a new binding to describe it, as it
does not really fit the rockchip-vpu binding, since there is no
decoder.

Signed-off-by: Nicolas Frattaroli <frattaroli.nicolas@gmail.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>

media: amphion: release core lock before reset vpu core

In reset vpu core, driver will wait for a response event,
but if there are still some events unhandled,
they will be handled first, driver may acquire core lock for that.
So if we do reset in core lock, it may led to reset timeout.

Fixes: 9f599f351e86a ("media: amphion: add vpu core driver")
Signed-off-by: Ming Qian <ming.qian@nxp.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>

media: Fix incorrect P010 chroma order description

The chroma order of P010 is `CbCr`,
match with the descriptions in `include/uapi/linux/videodev2.h` and the
documentation.

Fixes: 5374d8fb75f3 ("media: Add P010 video format")
Signed-off-by: Sebastian Fricke <sebastian.fricke@collabora.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>

media: docs: Fix VIVIOC typo

Replace VIVIOC_ with VIDIOC_ , trivial typo fix.

Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>

media: v4l2-ctrls: Fix missing newline in examples

Replace supportedn with supported\n , i.e. add the missing backslash.

Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>

media: platform: mtk-mdp: Fix mdp_ipi_comm structure alignment

The mdp_ipi_comm structure defines a command that is either
PROCESS (start processing) or DEINIT (destroy instance); we
are using this one to send PROCESS or DEINIT commands from Linux
to an MDP instance through a VPU write but, while the first wants
us to stay 4-bytes aligned, the VPU instead requires an 8-bytes
data alignment.

Keeping in mind that these commands are executed immediately
after sending them (hence not chained with others before the
VPU/MDP "actually" start executing), it is fine to simply add
a padding of 4 bytes to this structure: this keeps the same
performance as before, as we're still stack-allocating it,
while avoiding hackery inside of mtk-vpu to ensure alignment
bringing a definitely bigger performance impact.

Fixes: c8eb2d7e8202 ("[media] media: Add Mediatek MDP Driver")
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Houlong Wei <houlong.wei@mediatek.com>
Reviewed-by: Irui Wang <irui.wang@mediatek.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>

media: pvrusb2: drop unexpected word 'a' in comments

there is an unexpected word 'a' in the comments that need to be dropped

file - drivers/media/usb/pvrusb2/pvrusb2-hdw.c
line - 5044

But now it's a a chicken and egg problem...) */

changed to:

But now it's a chicken and egg problem...) */

Signed-off-by: Jiang Jian <jiangjian@cdjrlc.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>

media: ti: drop unexpected word 'a' in comments

there is an unexpected word 'a' in the comments that need to be dropped

file - drivers/media/platform/ti/cal/cal-camerarx.c
line - 308

 * DRA80xM TRMs have a a slightly simplified sequence.

changed to:

 * DRA80xM TRMs have a slightly simplified sequence.

Signed-off-by: Jiang Jian <jiangjian@cdjrlc.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>

media: gspca: drop unexpected word 'is' in the comments

there is an unexpected word 'is' in the comments that need to be dropped

file - drivers/media/usb/gspca/spca501.c
line - 491

* This is is for the 3com HomeConnect Lite which is spca501a based.

changed to:

* This is for the 3com HomeConnect Lite which is spca501a based.

Signed-off-by: Jiang Jian <jiangjian@cdjrlc.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>

media: cx18: Fix typo in comments

Remove the repeated word 'and' from comments

Signed-off-by: Jiang Jian <jiangjian@cdjrlc.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>

media: c8sectpfe: Remove unneeded NULL check before clk_disable_unprepare

clk_disable_unprepare() already checks NULL by using IS_ERR_OR_NULL.
Remove unneeded NULL check for fei->c8sectpfeclk.

Link: https://lore.kernel.org/linux-media/20220516131254.13816-1-wanjiabing@vivo.com
Signed-off-by: Wan Jiabing <wanjiabing@vivo.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>

media: c8sectpfe: Clean up handling of *_buffer_aligned

There are a few cases where code is harder than needed to read.
Improve those by:
- dropping unnecessary castings (see note below)
- use PTR_ALING() to be more explicit on what's going on there
- use proper definitions instead of hard coded values

Note, dropping castings will allow to perform an additional check
that type is not changed from void * to something else, e.g. u64,
which may very well break the bitmap APIs.

Link: https://lore.kernel.org/linux-media/20220209182521.55632-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Alain Volmat <alain.volmat@foss.st.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>

media: venus: hfi_platform: Correct supported codecs for sc7280

VP8 codec is deprecated for sc7280 SOC. Fix in platform layer to
update the supported codecs accordingly.

Signed-off-by: Vikash Garodia <quic_vgarodia@quicinc.com>
Acked-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Tested-by: Fritz Koenig<frkoenig@chromium.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>

media: venus: Add support for SSR trigger using fault injection

Here we introduce a new fault injection for SSR trigger.

To trigger the SSR:
 echo 100 >  /sys/kernel/debug/venus/fail_ssr/probability
 echo 1 >  /sys/kernel/debug/venus/fail_ssr/times

Co-developed-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Dikshita Agarwal <quic_dikshita@quicinc.com>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>

media: isl7998x: select V4L2_FWNODE to fix build error

Fix build error when VIDEO_ISL7998X=y and V4L2_FWNODE=m
by selecting V4L2_FWNODE.

microblaze-linux-ld: drivers/media/i2c/isl7998x.o: in function `isl7998x_probe':
(.text+0x8f4): undefined reference to `v4l2_fwnode_endpoint_parse'

Cc: stable@vger.kernel.org # 5.18 and above
Fixes: 51ef2be546e2 ("media: i2c: isl7998x: Add driver for Intersil ISL7998x")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Reported-by: kernel test robot <lkp@intel.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Pengutronix Kernel Team <kernel@pengutronix.de>
Reviewed-by: Michael Tretter <m.tretter@pengutronix.de>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>

media: mediatek: vcodec: Report supported bitrate modes

The media driver supports constant bitrate mode only.
The supported rate control mode is reported through querymenu() and
s_ctrl() fails if non constant bitrate mode (e.g. VBR) is requested.

Signed-off-by: Hirokazu Honda <hiroh@chromium.org>
Reviewed-by: Irui Wang <irui.wang@mediatek.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>

media: av7110: Remove duplicate 'with' in two places.

file: ./drivers/staging/media/av7110/av7110.c
line: 2367
         * reset with with MASK_31 to MC1
changed to
         * reset with MASK_31 to MC1

Signed-off-by: Jiang Jian <jiangjian@cdjrlc.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>

media: saa7164: Remove duplicate 'on' in two places.

file: drivers/media/pci/saa7164/saa7164-api.c
line: 804
/* Assumption: Hauppauge eeprom is at 0xa0 on on bus 0 */
changed to
/* Assumption: Hauppauge eeprom is at 0xa0 on bus 0 */

Signed-off-by: Jiang Jian <jiangjian@cdjrlc.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>

media: mediatek: vcodec: Fix non subdev architecture open power fail

According to subdev_bitmap bit value to open hardware power, need to
set subdev_bitmap value for non subdev architecture.

Fixes: c05bada35f01 ("media: mtk-vcodec: Add to support multi hardware decode")
Signed-off-by: Yunfei Dong <yunfei.dong@mediatek.com>
Reviewed-by: Chen-Yu Tsai <wenst@chromium.org>
Tested-by: Chen-Yu Tsai <wenst@chromium.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>

media: usb: gspca: aligned '*' each line

Consider "*" alignment in comments

Signed-off-by: Jiang Jian <jiangjian@cdjrlc.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>

media: tw686x: Fix memory leak in tw686x_video_init

video_device_alloc() allocates memory for vdev,
when video_register_device() fails, it doesn't release the memory and
leads to memory leak, call video_device_release() to fix this.

Fixes: 704a84ccdbf1 ("[media] media: Support Intersil/Techwell TW686x-based video capture cards")
Signed-off-by: Miaoqian Lin <linmq006@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>

media: driver/nxp/imx-jpeg: fix a unexpected return value problem

In function mxc_jpeg_probe(), when devm_clk_get() fail, the return value
will be unexpected, and it should be the devm_clk_get's error code.

Fixes: 4c2e5156d9fa6 ("media: imx-jpeg: Add pm-runtime support for imx-jpeg")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Jian Zhang <zhangjian210@huawei.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>

media: MAINTAINERS: add Yunfei Dong as mediatek vcodec driver maintainer

I have been working on mediatek driver development for a very long time,
and sent many patches to change the driver architecture. Add myself as
co-maintainer for mediatek vcodec driver.

Signed-off-by: Yunfei Dong <yunfei.dong@mediatek.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>

media: mediatek: vcodec: Skip SOURCE_CHANGE & EOS events for stateless

The stateless decoder API does not specify the usage of SOURCE_CHANGE
and EOF events. These events are used by stateful decoders to signal
changes in the bitstream. They do not make sense for stateless decoders.

Do not handle subscription for these two types of events for stateless
decoder instances. This fixes the last v4l2-compliance error:

Control ioctls:
fail: v4l2-test-controls.cpp(946): have_source_change || have_eos
test VIDIOC_(UN)SUBSCRIBE_EVENT/DQEVENT: FAIL

Fixes: 8cdc3794b2e3 ("media: mtk-vcodec: vdec: support stateless API")
Signed-off-by: Chen-Yu Tsai <wenst@chromium.org>
Reviewed-by: Nicolas Dufresne <nicolas.dufresne@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>

media: tw686x: Fix an error handling path in tw686x_probe()

The commit in Fixes: is incomplete. It has moved some code in the probe but
not all error handling paths have been updated.

Now, if request_irq() fails, we must release some resources.

Fixes: c8946454ed96 ("media: tw686x: Register the irq at the end of probe")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>

media: stm32: dcmi: Drop always NULL sd_state from dcmi_pipeline_s_fmt()

The second argument is always NULL, stop passing it to the function.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alain Volmat <alain.volmat@foss.st.com>
Cc: Alexandre Torgue <alexandre.torgue@foss.st.com>
Cc: Amelie DELAUNAY <amelie.delaunay@foss.st.com>
Cc: Hugues FRUCHET <hugues.fruchet@foss.st.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Philippe CORNU <philippe.cornu@foss.st.com>
Cc: linux-stm32@st-md-mailman.stormreply.com
Cc: linux-arm-kernel@lists.infradead.org
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>

media: stm32: dcmi: Fill in remaining Bayer formats

Fill in 10, 12, 14 bit Bayer formats into the DCMI driver.
Those are useful e.g. when MT9P006 sensor is connected.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alain Volmat <alain.volmat@foss.st.com>
Cc: Alexandre Torgue <alexandre.torgue@foss.st.com>
Cc: Amelie DELAUNAY <amelie.delaunay@foss.st.com>
Cc: Hugues FRUCHET <hugues.fruchet@foss.st.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Philippe CORNU <philippe.cornu@foss.st.com>
Cc: linux-stm32@st-md-mailman.stormreply.com
Cc: linux-arm-kernel@lists.infradead.org
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>

media: mediatek: vcodec: Initialize decoder parameters after getting dec_capability

Need to get dec_capability from scp first, then initialize decoder
supported format and other parameters according to dec_capability value.

Fixes: fd00d90330d1 ("media: mtk-vcodec: vdec: move stateful ops into their own file")
Signed-off-by: Yunfei Dong <yunfei.dong@mediatek.com>
Reviewed-by: Chen-Yu Tsai <wenst@chromium.org>
Tested-by: Chen-Yu Tsai <wenst@chromium.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>

media: rkvdec:Remove redundant memset

As dma_alloc_coherent() will return a zeroed buffer, we
don't need to memset the returned buffer.
priv_tbl = dma_alloc_coherent() and count_tbl = dma_alloc_coherent()
should be enough.

-see commit 750afb08ca71 ("cross-tree: phase out dma_zalloc_coherent()")

Signed-off-by: Zhang Zekun <zhangzekun11@huawei.com>
Reviewed-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>

media: atmel: atmel-isc-base: allow wb ctrls to be changed when isc is not configured

When attempting to change the white balance (WB) ctrls before starting
streaming, e.g.:

 # v4l2-ctl -L

User Controls
..
            blue_component_gain 0x009819c1 (int)    : min=0 max=8191 step=1 default=512 value=512 flags=slider
..
 # v4l2-ctl --set-ctrl=blue_component_gain=500
 # v4l2-ctl -L
..
            blue_component_gain 0x009819c1 (int)    : min=0 max=8191 step=1 default=512 value=500 flags=slider
..

These will not be written to the internal data struct and will not be
written to the WB hardware module.
Thus, after starting streaming, they will be reset to default:

 # v4l2-ctl -L
..
            blue_component_gain 0x009819c1 (int)    : min=0 max=8191 step=1 default=512 value=512 flags=slider
..

It does not make much sense to not be able to configure the WB controls
at all times. Even if the sensor would not be RAW Bayer (and in this case the
WB module is unavailable), the user could configure the ISC itself, as the
ISC should not care about the sensor format.
Thus, when WB module is available (if the sensor changes format e.g.) it will
be already configured as be user's desires.
In consequence, remove the check in isc_s_awb_ctrl that will return if ISC
does not know the sensor format.

Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>

media: sta2x11: remove VIRT_TO_BUS dependency

This driver does not use the virt_to_bus() function, though it
depends on x86 specific fixups in the swiotlb code, which was
last rewritten in commit e380a0394c36 ("x86/PCI: sta2x11: use
default DMA address translation").

It is possible that the driver still fails to build on some
architectures that are missing CONFIG_VIRT_TO_BUS, but it is
always set on x86 machines with the STA2X11 platform enabled.

More likely though is that it was never meant to depend on
CONFIG_VIRT_TO_BUS, and the Kconfig dependency was kept from
an out-of-tree version when the driver was originally merged.

Fixes: efeb98b4e2b2 ("[media] STA2X11 VIP: new V4L2 driver")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>

media: mediatek: vcodec: return EINVAL if plane is too small

Modify vb2ops_vdec_buf_prepare to return EINVAL if the size of the plane
is less than the size of the image. Currently we just log an error and
return 0 anyway, which may cause a buffer overrun bug.

Signed-off-by: Justin Green <greenjustin@chromium.org>
Suggested-by: Andres Calderon Jaramillo <andrescj@chromium.org>
Reviewed-by: Nicolas Dufresne <nicolas.dufresne@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>

media: v4l2-mem2mem: prevent pollerr when last_buffer_dequeued is set

If the last buffer was dequeued from the capture queue,
signal userspace. DQBUF(CAPTURE) will return -EPIPE.

But if output queue is empty and capture queue is empty,
v4l2_m2m_poll_for_data will return EPOLLERR,
This is very easy to happen in drain.

When last_buffer_dequeued is set, we shouldn't return EPOLLERR,
but return EPOLLIN | EPOLLRDNORM.

Fixes: 1698a7f151126 ("media: v4l2-mem2mem: simplify poll logic")
Signed-off-by: Ming Qian <ming.qian@nxp.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>

media: mediatek: vcodec: remove unneeded semicolon

Eliminate the following coccicheck warning:
./drivers/media/platform/mediatek/vcodec/mtk_vcodec_dec.c:71:2-3: Unneeded semicolon

Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: Yang Li <yang.lee@linux.alibaba.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>

media: hdpvr: fix error value returns in hdpvr_read

Error return values are supposed to be negative in hdpvr_read. Most
error returns are currently handled via an unsigned integer "ret". When
setting a negative error value to "ret", the value actually becomes a
large positive value, because "ret" is unsigned. Later on, the "ret"
value is returned. But as ssize_t is a 64-bit signed number, the error
return value stays a large positive integer instead of a negative
integer. This can cause an error value to be interpreted as the read
size, which can cause a buffer overread for applications relying on the
returned size.

Fixes: 9aba42efe85b ("V4L/DVB (11096): V4L2 Driver for the Hauppauge HD PVR usb capture device")
Signed-off-by: Niels Dossche <dossche.niels@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>

media: mediatek: vcodec: fix minmax.cocci warning

Fix the following coccicheck warning:

drivers/media/platform/mediatek/vcodec/vdec/vdec_vp9_req_lat_if.c:
694:15-16: WARNING opportunity for min().

Signed-off-by: Guo Zhengkui <guozhengkui@vivo.com>
Reviewed-by: Nicolas Dufresne <nicolas.dufresne@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>

media: MAINTAINERS: add include/dt-bindings/media to MEDIA INPUT INFRASTRUCTURE

Maintainers of the directory Documentation/devicetree/bindings/media
are also the maintainers of the corresponding directory
include/dt-bindings/media.

Add the file entry for include/dt-bindings/media to the appropriate
section in MAINTAINERS.

Signed-off-by: Lukas Bulwahn <lukas.bulwahn@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>

media: ddbridge: Remove useless license text when SPDX-License-Identifier is already used

An SPDX-License-Identifier is already in place. There is no need to
duplicate part of the corresponding license.

While at it, a few comments at the end of some .h files have been updated
to reflect the correct include guard name (missing '_' and co.)

Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>

media: em28xx: Remove useless license text when SPDX-License-Identifier is already used

An SPDX-License-Identifier is already in place. There is no need to
duplicate part of the corresponding license.

Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>

media: rcar_drif: Remove useless license text when SPDX-License-Identifier is already used

An SPDX-License-Identifier is already in place. There is no need to
duplicate part of the corresponding license.

This is a left-over from commit adeb69705682 ("media: rcar_drif: convert to
SPDX identifiers")

Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>

media: platform: cros-ec: Add kinox to the match table

The Google Kinox device uses the same approach as the Google Brask
which enables the HDMI CEC via the cros-ec-cec driver.

Signed-off-by: Ajye Huang <ajye_huang@compal.corp-partner.google.com>
Reviewed-by: Guenter Roeck <groeck@chromium.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>

media: amphion: output firmware error message

Firmware may send the error event with some error message,
and it help locate the firmware error,
so output the error message if it exists

Fixes: 61cbf1c1fa6d7 ("media: amphion: implement vpu core communication based on mailbox")
Signed-off-by: Ming Qian <ming.qian@nxp.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>

media: imx-jpeg: Disable slot interrupt when frame done

The interrupt STMBUF_HALF may be triggered after frame done.
It may led to system hang if driver try to access the register after
power off.

Disable the slot interrupt when frame done.

Fixes: 2db16c6ed72ce ("media: imx-jpeg: Add V4L2 driver for i.MX8 JPEG Encoder/Decoder")
Signed-off-by: Ming Qian <ming.qian@nxp.com>
Reviewed-by: Mirela Rabulea <mirela.rabulea@nxp.com>
Tested-by: Mirela Rabulea <mirela.rabulea@nxp.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>

media: mediatek: vcodec: Change encoder v4l2 capability value

Change the value of v4l2 capability parameters: driver and card.

Signed-off-by: Yunfei Dong <yunfei.dong@mediatek.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>

media: mediatek: vcodec: Fix encoder v4l2 bus_info not correctly

Fix v4l2 capability bus_info value with correct chip name according to
compatible.

Signed-off-by: Yunfei Dong <yunfei.dong@mediatek.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>

media: mediatek: vcodec: Change decoder v4l2 capability value

Change the value of v4l2 capability parameters: driver and card.

Signed-off-by: Yunfei Dong <yunfei.dong@mediatek.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>

media: mediatek: vcodec: Fix decoder v4l2 bus_info not correctly

Fix v4l2 capability bus_info value with correct chip name according to
compatible.

Signed-off-by: Yunfei Dong <yunfei.dong@mediatek.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>

media: rkisp1: Drop parentheses and fix indentation in rkisp1_probe()

Fix a small indentation issue to increase code readability, and drop
unneeded parentheses.

Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Ricardo Ribalda <ribalda@chromium.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>

media: rkisp1: Align macro definitions

Make the code more readable by using the same alignment for all macros
in rkisp1-common.h.

Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Ricardo Ribalda <ribalda@chromium.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>

media: rkisp1: capture: Bypass the main device for handling querycap

When handling querycap, the capture node would access the main rkisp1
device unnecessarily. Get the information from the most direct source.

Signed-off-by: Paul Elder <paul.elder@ideasonboard.com>
Reviewed-by: Dafna Hirschfeld <dafna@fastmail.com>
Reviewed-by: Ricardo Ribalda <ribalda@chromium.org>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>

media: rkisp1: debug: Update max register name length

Update the maximum register name length to match all the registers being
printed. This helps getting a consistent alignment of register dumps
when concatenating multiple debugfs files.

Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Ricardo Ribalda <ribalda@chromium.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>

media: rkisp1: debug: Consolidate reg dumps for shadow registers

Extend the rkisp1_debug_register structure and the
rkisp1_debug_dump_regs() function to support shadow registers, and
replace the manual registers dump implementation in
rkisp1_debug_dump_rsz_regs_show() with a call to
rkisp1_debug_dump_regs().

Support for printing register values in decimal is dropped, as it was
actually confusing to print resizer register expressed as fixed-point
values in decimal.

Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Ricardo Ribalda <ribalda@chromium.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>

media: rkisp1: debug: Move resizer register dump to debugfs

The debugfs support already includes support to dump core and ISP
registers. Move the resizer register dump there too to make the
userspace interface consistent.

Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Ricardo Ribalda <ribalda@chromium.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>

media: rkisp1: debug: Add debugfs files to dump core and ISP registers

It's useful to dump the value of registers for debugging purpose. Add
two debugfs files to dump key core and ISP registers.

Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Paul Elder <paul.elder@ideasonboard.com>
Reviewed-by: Ricardo Ribalda <ribalda@chromium.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>

media: rkisp1: debug: Collect input status by sampling ISP_FLAGS_SHD

The ISP_FLAGS_SHD register exposes the ISP parallel input signals (data
and synchronization) in real time. This can help debugging when the
device doesn't output any image. Sample the register 10000 times with a
1µs delay and expose the result through debugfs.

Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Paul Elder <paul.elder@ideasonboard.com>
Reviewed-by: Ricardo Ribalda <ribalda@chromium.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>

media: rkisp1: Compile debugfs support conditionally

When CONFIG_DEBUGFS is disabled, there's no need to compile the debugfs
support in. Make it conditional.

Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Dafna Hirschfeld <dafna@fastmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>

media: rkisp1: Move debugfs code to a separate file

To avoid cluttering the main rkisp1-dev.c driver file, move debugfs code
to a separate source file. This prepares for extensions to the debugfs
infrastructure.

While at it, add a missing forward declaration for struct dentry in
rkisp1-common.h to avoid depending on indirect includes.

Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Dafna Hirschfeld <dafna@fastmail.com>
Reviewed-by: Ricardo Ribalda <ribalda@chromium.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>

media: rkisp1: resizer: Simplify register access

The registers for the mainpath and selfpath resizers are located at the
same offset from the instance-specific base. Use this to simplify
register access, removing the need to store per-register offsets in the
rkisp1_rsz_config structure.

Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Ricardo Ribalda <ribalda@chromium.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>

media: rkisp1: Swap value and address arguments to rkisp1_write()

While writel() takes the value and address arguments in that order, most
write functions (including in the regmap API) use the opposite
convention. Having the value first is considered confusing, and often
leads to more difficult to read code compared to the opposite convention
where the write call and the register name often fit on a single line:

rkisp1_write(rkisp1, RKISP1_CIF_THE_REG_NAME,
     complicate_calculation + for / the_register
     value + goes | here);

Swap the arguments of the rkisp1_write() function, and use the following
semantic patch to update the callers:

@@
expression rkisp1, value, address;
@@

- rkisp1_write(rkisp1, value, address)
+ rkisp1_write(rkisp1, address, value)

This commit also includes a few additional line break cleanups in the
rkisp1_write() calls, but no other manual change.

Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Dafna Hirschfeld <dafna@fastmail.com>
Reviewed-by: Ricardo Ribalda <ribalda@chromium.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>

media: rkisp1: regs: Rename CCL, ICCL and IRCL registers with VI_ prefix

The documentation names the CCL, ICCL and IRCL registers with a VI_
prefix, like the VI_ID and VI_DPCL registers. Fix the macro names
accordingly.

Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Dafna Hirschfeld <dafna@fastmail.com>
Reviewed-by: Ricardo Ribalda <ribalda@chromium.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>

media: rkisp1: regs: Don't use BIT() macro for multi-bit register fields

The BIT() macro is meant to represent a single bit. It is incorrectly
used for register field values that store the value 1 in a multi-bit
field. Use the usual (1 << n) construct for those.

While at it, move RKISP1_CIF_MI_DMA_CTRL_READ_FMT_PACKED where it
belongs with the other READ_FMT values.

Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Ricardo Ribalda <ribalda@chromium.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>