arm64: dts: qcom: sdm845-db845c: Add hdmi bridge nodes

Enable MDSS and DSI and add the LT9611 HDMI bridge. Also add the HDMI
audio nodes.

Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Co-developed-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Link: https://lore.kernel.org/r/20200727075532.1932134-1-vkoul@kernel.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>

arm64: dts: qcom: add sm8250 GPU nodes

This brings up the GPU. Tested on HDK865 by running vulkan CTS.

Signed-off-by: Jonathan Marek <jonathan@marek.ca>
Link: https://lore.kernel.org/r/20200709135251.643-15-jonathan@marek.ca
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>

arm64: dts: qcom: add sm8150 GPU nodes

This brings up the GPU. Tested on HDK855 by running vulkan CTS.

Signed-off-by: Jonathan Marek <jonathan@marek.ca>
Link: https://lore.kernel.org/r/20200709135251.643-14-jonathan@marek.ca
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>

dt-bindings: power: Add missing rpmpd rpmh regulator level

Add RPMH_REGULATOR_LEVEL_SVS_L0, used by sm8250.

Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Jonathan Marek <jonathan@marek.ca>
Link: https://lore.kernel.org/r/20200709135251.643-13-jonathan@marek.ca
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>

arm64: dts: qcom: sc7180: Add opp-peak-kBps to GPU opp

Add opp-peak-kBps bindings to the GPU opp table, listing the peak
GPU -> DDR bandwidth requirement for each opp level. This will be
used to scale the DDR bandwidth along with the GPU frequency dynamically.

Signed-off-by: Sharat Masetty <smasetty@codeaurora.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Akhil P Oommen <akhilpo@codeaurora.org>
Link: https://lore.kernel.org/r/1594992579-20662-7-git-send-email-akhilpo@codeaurora.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>

arm64: dts: qcom: sc7180: Add interconnects property for GPU

This patch adds the interconnects property to the GPU node. This enables
the GPU->DDR path bandwidth voting.

Signed-off-by: Sharat Masetty <smasetty@codeaurora.org>
Signed-off-by: Akhil P Oommen <akhilpo@codeaurora.org>
Link: https://lore.kernel.org/r/1594992579-20662-6-git-send-email-akhilpo@codeaurora.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>

arm64: dts: qcom: SDM845: Enable GPU DDR bw scaling

This patch adds the interconnects property for the gpu node and the
opp-peak-kBps property to the opps of the gpu opp table. This should
help enable DDR bandwidth scaling dynamically and proportionally to the
GPU frequency.

Signed-off-by: Sharat Masetty <smasetty@codeaurora.org>
Signed-off-by: Akhil P Oommen <akhilpo@codeaurora.org>
Link: https://lore.kernel.org/r/1594992579-20662-5-git-send-email-akhilpo@codeaurora.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>

arm64: dts: qcom: sc7180: Add support for context losing replicator

Add "qcom,replicator-loses-context" property to the replicator
in Always-on domain in SC7180 SoC to enable coresight replicator
driver to handle this variation of replicator designs.

Reviewed-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Sai Prakash Ranjan <saiprakash.ranjan@codeaurora.org>
Link: https://lore.kernel.org/r/5072d94849cfaee46748d26ac997212fb2d783c2.1591708204.git.saiprakash.ranjan@codeaurora.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>

arm64: dts: qcom: sc7180: Add iommus property to ETR

Define iommus property for Coresight ETR component in
SC7180 SoC with the SID and mask to enable SMMU
translation for this master.

Signed-off-by: Sai Prakash Ranjan <saiprakash.ranjan@codeaurora.org>
Link: https://lore.kernel.org/r/2312c9a10e7251d69e31e4f51c0f1d70e6f2f2f5.1591708204.git.saiprakash.ranjan@codeaurora.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>

arm64: dts: qcom: sc7180: Add support to skip powering up of ETM

Add "qcom,skip-power-up" property to skip powering up ETM
on SC7180 SoC to workaround a hardware errata where CPU
watchdog counter is stopped when ETM power up bit is set
(i.e., when TRCPDCR.PU = 1).

Reviewed-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Sai Prakash Ranjan <saiprakash.ranjan@codeaurora.org>
Link: https://lore.kernel.org/r/8c5ff297d8c89d9d451352f189baf26c8938842a.1591708204.git.saiprakash.ranjan@codeaurora.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>

arm64: dts: qcom: sc7180: Add properties to qfprom for fuse blowing

This patch adds properties to the qfprom node to enable fuse blowing.

Signed-off-by: Ravi Kumar Bokka <rbokka@codeaurora.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20200710073439.v5.4.I70c17309f8b433e900656d7c53a2e6b61888bb68@changeid
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>

arm64: dts: qcom: sc7180: Add maximum speed property for DWC3 USB node

Adding maximum speed property for DWC3 USB node which can be used
for setting interconnect bandwidth.

Signed-off-by: Sandeep Maheswaram <sanm@codeaurora.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Link: https://lore.kernel.org/r/1595317489-18432-3-git-send-email-sanm@codeaurora.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>

arm64: dts: qcom: sdm845: Support ETMv4 power management

Add "arm,coresight-loses-context-with-cpu" property to coresight
ETM nodes to avoid failure of trace session because of losing
context on entering deep idle states.

Reviewed-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Sai Prakash Ranjan <saiprakash.ranjan@codeaurora.org>
Link: https://lore.kernel.org/r/20200721071343.2898-1-saiprakash.ranjan@codeaurora.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>

arm64: dts: qcom: pmi8998: Add nodes for LAB and IBB regulators

This patch adds devicetree nodes for LAB and IBB regulators.

Signed-off-by: Nisha Kumari <nishakumari@codeaurora.org>
[sumits: Updated for better compatible strings and names]
Signed-off-by: Sumit Semwal <sumit.semwal@linaro.org>
Link: https://lore.kernel.org/r/20200622124110.20971-4-sumit.semwal@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>

arm64: dts: sc7180: Add DSI and MDP OPP tables and power-domains

Add the OPP tables for DSI and MDP based on the perf state/clk
requirements, and add the power-domains property to specify the
scalable power domain.

Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Link: https://lore.kernel.org/r/1594292674-15632-5-git-send-email-rnayak@codeaurora.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>

arm64: dts: sdm845: Add DSI and MDP OPP tables and power-domains

Add the OPP tables for DSI and MDP based on the perf state/clk
requirements, and add the power-domains property to specify the
scalable power domain.

Tested-by: Rob Clark <robdclark@gmail.com>
Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Link: https://lore.kernel.org/r/1594292674-15632-4-git-send-email-rnayak@codeaurora.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>

arm64: dts: qcom: sc7180: Move the fixed-perm property to SoC dtsi

All the platforms using SC7180 SoC are expected to have the wlan firmware
memory statically mapped by the Trusted Firmware. Hence move back the
qcom,msa-fixed-perm property to the SoC dtsi.

Reviewed-by: Douglas Anderson <dianders@chromium.org>
Fixes: 7d484566087c0 ("arm64: dts: qcom: sc7180: Add missing properties for Wifi node")
Signed-off-by: Sibi Sankar <sibis@codeaurora.org>
Link: https://lore.kernel.org/r/20200716191746.23196-1-sibis@codeaurora.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>

arm64: dts: qcom: msm8916-samsung-a2015: Add accelerometer/magnetometer

A3U/A5U both use a Bosch BMC150 accelerometer/magnetometer combo.
The chip provides two separate I2C devices for the accelerometer
and magnetometer that are already supported by the bmc150-accel
and bmc150-magn driver.

The only difference between A3U/A5U is the way the sensor is
mounted on the mainboard - set the mount-matrix in the
device-specific device tree part to handle that difference.

Co-developed-by: Michael Srba <michael.srba@seznam.cz>
Signed-off-by: Michael Srba <michael.srba@seznam.cz>
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Link: https://lore.kernel.org/r/20200622151751.408995-5-stephan@gerhold.net
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>

arm64: dts: qcom: msm8916: Use higher I2C drive-strength only on DB410c

Commit c240f29e75e6 ("arm64: dts: set the default i2c pin drive strength to 16mA")
changed the default drive-strength for I2C pins in msm8916-pins.dtsi
to the maximum possible (16 mA).

While this makes sense for apq8016-sbc (DB410c) where you can connect
an arbitrary amount of I2C devices with level shifters etc, there is
no need to use a higher drive strength for other MSM8916 devices.
The minimum drive strength (2 mA) seems to be totally sufficient
to have everything work there.

With the short pinctrl nodes introduced earlier we can easily override
the drive-strength only for apq8016-sbc now. Use that and change
the default back to 2 mA.

i2c1_default/i2c5_default are already using 2 mA because they were
added separately later and are not used in apq8016-sbc.

Cc: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Link: https://lore.kernel.org/r/20200622151751.408995-4-stephan@gerhold.net
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>

arm64: dts: qcom: msm8916: Simplify pinctrl configuration

So far we have been separating pinctrl entries into pinmux/pinconf.
It turns out it is also possible to combine them: The advantage is
that the device tree is overall more concise because the "pins"
to configure just need to be specified once, not separately for
pinmux/pinconf.

Using the simpler form only for new entries would be rather confusing.
This commit makes all MSM8916 device trees use the simplfied form.

Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Link: https://lore.kernel.org/r/20200622151751.408995-3-stephan@gerhold.net
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>

arm64: dts: msm8916-samsung/longcheer: Move pinctrl/regulators to end of file

It is helpful to be able to see all hardware components in one part
of the device tree, without having to scroll over the large amount
of regulator/pinctrl nodes. Keep those separated at the end of the file
to make navigation a bit easier.

This also makes it consistent with the order used in apq8016-sbc.dtsi.

Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Link: https://lore.kernel.org/r/20200622151751.408995-2-stephan@gerhold.net
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>

arm64: dts: qcom: sm8250: Drop tcsr_mutex syscon

Now that we don't need the intermediate syscon to represent the TCSR
mutexes, update the dts to describe the TCSR mutex directly under /soc.

Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20200622075956.171058-5-bjorn.andersson@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>

arm64: dts: qcom: sc7180: Add missing properties for Wifi node

The wlan firmware memory is statically mapped in
the Trusted Firmware, hence the wlan driver does
not need to map/unmap this region dynamically.

Hence add the property to indicate the wlan driver
to not map/unamp the firmware memory region
dynamically.

Also add the chain1 voltage supply for wlan.

Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Rakesh Pillai <pillair@codeaurora.org>
Link: https://lore.kernel.org/r/1594615586-17055-1-git-send-email-pillair@codeaurora.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>

arm64: dts: qcom: Fix WiFi supplies on sc7180-idp

The WiFi supplies that were added recently can't have done anything
useful because they were missing the "-supply" suffix.  Booting
without the "-supply" suffix would give these messages:

ath10k_snoc 18800000.wifi: 18800000.wifi supply vdd-0.8-cx-mx not found, using dummy regulator
ath10k_snoc 18800000.wifi: 18800000.wifi supply vdd-1.8-xo not found, using dummy regulator
ath10k_snoc 18800000.wifi: 18800000.wifi supply vdd-1.3-rfa not found, using dummy regulator
ath10k_snoc 18800000.wifi: 18800000.wifi supply vdd-3.3-ch0 not found, using dummy regulator

Let's add the "-supply" suffix.

Tested-by: Rakesh Pillai <pillair@codeaurora.org>
Reviewed-by: Rakesh Pillai <pillair@codeaurora.org>
Fixes: 1e7594a38f37 ("arm64: dts: qcom: sc7180: Add WCN3990 WLAN module device node")
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20200625131658.REPOST.1.I32960cd32bb84d6db4127c906d7e371fa29caebf@changeid
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>

arm64: dts: sdm845: add Inline Crypto Engine registers and clock

Add the vendor-specific registers and clock for Qualcomm ICE (Inline
Crypto Engine) to the device tree node for the UFS host controller on
sdm845, so that the ufs-qcom driver will be able to use inline crypto.

Use a separate register range rather than extending the main UFS range
because there's a gap between the two, and the ICE registers are
vendor-specific.  (Actually, the hardware claims that the ICE range also
includes the array of standard crypto configuration registers; however,
on this SoC the Linux kernel isn't permitted to access them directly.)

Signed-off-by: Eric Biggers <ebiggers@google.com>
Link: https://lore.kernel.org/r/20200710072013.177481-4-ebiggers@kernel.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>

arm64: dts: sc7180: Add sdhc opps and power-domains

Add the power domain supporting performance state and the corresponding
OPP tables for the sdhc device on sc7180.

Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org>
Link: https://lore.kernel.org/r/1593506712-24557-5-git-send-email-rnayak@codeaurora.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>

arm64: dts: sdm845: Add sdhc opps and power-domains

Add the power domain supporting performance state and the corresponding
OPP tables for the sdhc device on sdm845.

Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org>
Link: https://lore.kernel.org/r/1593506712-24557-4-git-send-email-rnayak@codeaurora.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>

arm64: dts: sc7180: Add OPP table for all qup devices

qup has a requirement to vote on the performance state of the CX domain
in sc7180 devices. Add OPP tables for these and also add power-domains
property for all qup instances for uart and spi.
i2c does not support scaling and uses a fixed clock.

Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org>
Link: https://lore.kernel.org/r/1593506712-24557-3-git-send-email-rnayak@codeaurora.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>

arm64: dts: sdm845: Add OPP table for all qup devices

qup has a requirement to vote on the performance state of the CX domain
in sdm845 devices. Add OPP tables for these and also add power-domains
property for all qup instances for uart and spi.
i2c does not support scaling and uses a fixed clock.

Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/1593506712-24557-2-git-send-email-rnayak@codeaurora.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>

arm64: dts: sc7180: Add qspi opps and power-domains

Add the power domain supporting performance state and the corresponding
OPP tables for the qspi device on sc7180

Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org>
Link: https://lore.kernel.org/r/1593769293-6354-4-git-send-email-rnayak@codeaurora.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>

arm64: dts: sdm845: Add qspi opps and power-domains

Add the power domain supporting performance state and the corresponding
OPP tables for the qspi device on sdm845

Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org>
Link: https://lore.kernel.org/r/1593769293-6354-3-git-send-email-rnayak@codeaurora.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>

arm64: dts: qcom: sdm845: Add cpu OPP tables

Add OPP tables required to scale DDR/L3 per freq-domain on SDM845 SoCs.

Tested-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Sibi Sankar <sibis@codeaurora.org>
Link: https://lore.kernel.org/r/20200702204643.25785-1-sibis@codeaurora.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>

arm64: dts: qcom: sc7180: Drop the unused non-MSA SID

Having a non-MSA (Modem Self-Authentication) SID bypassed breaks modem
sandboxing i.e if a transaction were to originate from it, the hardware
memory protections units (XPUs) would fail to flag them (any transaction
originating from modem are historically termed as an MSA transaction).
Drop the unused non-MSA modem SID on SC7180 SoCs and cheza so that SMMU
continues to block them.

Tested-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Sai Prakash Ranjan <saiprakash.ranjan@codeaurora.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Fixes: bec71ba243e95 ("arm64: dts: qcom: sc7180: Update Q6V5 MSS node")
Fixes: 68aee4af5f620 ("arm64: dts: qcom: sdm845-cheza: Add iommus property")
Cc: stable@vger.kernel.org
Reported-by: Sai Prakash Ranjan <saiprakash.ranjan@codeaurora.org>
Signed-off-by: Sibi Sankar <sibis@codeaurora.org>
Link: https://lore.kernel.org/r/20200630081938.8131-1-sibis@codeaurora.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>

arm64: dts: qcom: sdm845: Add IMEM and PIL info region

Add a simple-mfd representing IMEM on SDM845 and define the PIL
relocation info region, so that post mortem tools will be able to locate
the loaded remoteprocs.

Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20200622191942.255460-6-bjorn.andersson@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>

arm64: dts: qcom: qcs404: Add IMEM and PIL info region

Add a simple-mfd representing IMEM on QCS404 and define the PIL
relocation info region, so that post mortem tools will be able to locate
the loaded remoteprocs.

Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20200622191942.255460-5-bjorn.andersson@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>

arm64: dts: qcom: sc7180: Add cpu OPP tables

Add OPP tables required to scale DDR/L3 per freq-domain on SC7180 SoCs.

Reviewed-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Sibi Sankar <sibis@codeaurora.org>
Link: https://lore.kernel.org/r/20200626190808.8716-1-sibis@codeaurora.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>

arm64: dts: sc7180: Add interconnect for QUP and QSPI

Add interconnect ports for GENI QUPs and QSPI to set bus capabilities.

Signed-off-by: Akash Asthana <akashast@codeaurora.org>
Link: https://lore.kernel.org/r/1592908737-7068-9-git-send-email-akashast@codeaurora.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>

arm64: dts: ipq8074: enable USB support

IPQ8074 has two super speed usb ports, add phy and dwc3 nodes
to enable them.

Signed-off-by: Sivaprakash Murugesan <sivaprak@codeaurora.org>
Link: https://lore.kernel.org/r/1591625479-4483-6-git-send-email-sivaprak@codeaurora.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>

arm64: dts: qcom: angler: Add qcom,msm-id and pmic-id

Add properties required for the bootloader to select
the correct bootloader blob. They have been removed from
the SoC device tree as they should be set on a per-device
basis.

Signed-off-by: Konrad Dybcio <konradybcio@gmail.com>
Link: https://lore.kernel.org/r/20200623224813.297077-11-konradybcio@gmail.com
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>

arm64: dts: qcom: msm8994: Add PSCI node

Add PSCI node to enable multi-processor startup.

Note that not every 8994 device firmware supports PSCI,
and even if, then it can only start the cores and not
shut them down.

Signed-off-by: Konrad Dybcio <konradybcio@gmail.com>
Link: https://lore.kernel.org/r/20200623224813.297077-10-konradybcio@gmail.com
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>

arm64: dts: qcom: msm8994: Add pmu node

Add the CPU PMU to get perf support for hardware events.

Signed-off-by: Konrad Dybcio <konradybcio@gmail.com>
Link: https://lore.kernel.org/r/20200623224813.297077-9-konradybcio@gmail.com
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>

arm64: dts: qcom: msm8994: Add I2C, SPI and BLSP DMA nodes

Add support for I2C and SPI buses to enable peripherals
such as touchscreens or sensors. Also add DMA nodes,
configuration and BLSP2 UART2 interface.

Signed-off-by: Konrad Dybcio <konradybcio@gmail.com>
Link: https://lore.kernel.org/r/20200623224813.297077-8-konradybcio@gmail.com
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>

arm64: dts: qcom: msm8994: Add SDHCI1 node

Enable support for SDHCI on msm8994-based devices.

Signed-off-by: Konrad Dybcio <konradybcio@gmail.com>
Link: https://lore.kernel.org/r/20200623224813.297077-6-konradybcio@gmail.com
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>

arm64: dts: qcom: msm8994: Add a proper CPU map

Add a proper CPU map to enable the use of all 8 cores.

Signed-off-by: Konrad Dybcio <konradybcio@gmail.com>
Link: https://lore.kernel.org/r/20200623224813.297077-4-konradybcio@gmail.com
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>

arm64: dts: qcom: msm8994: Add SPMI PMIC arbiter device

Add SPMI PMIC arbiter device to communicate with PMICs
attached to SPMI bus.

Signed-off-by: Konrad Dybcio <konradybcio@gmail.com>
Link: https://lore.kernel.org/r/20200623224813.297077-3-konradybcio@gmail.com
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>

arm64: dts: qcom: msm8994: Modernize the DTS style

Following changes have been made:

- remove name, compatible and msm-id
- wrap clocks in clocks{}
- order nodes by name and by address
- clock_gcc -> gcc
- msmgpio -> tlmm
- qcom,smem -> smem
- remove unit-address from smem
- retire msm8994-pins.dtsi
- add some of the missing pins
- make comments C-style

Signed-off-by: Konrad Dybcio <konradybcio@gmail.com>
Link: https://lore.kernel.org/r/20200623224813.297077-2-konradybcio@gmail.com
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>

arm64: dts: qcom: sm8250: Add remoteprocs

Add remoteproc nodes for the audio, compute and sensor cores, define
glink for each one and enable them on the MTP with appropriate firmware
defined.

Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Vinod Koul <vkoul@kernel.org>
Link: https://lore.kernel.org/r/20200622222747.717306-6-bjorn.andersson@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>

arm64: dts: qcom: sm8250: Add SMP2P nodes

SMP2P is used for interrupting and being interrupted about remoteproc
state changes related to the audio, compute and sensor subsystems.

Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Vinod Koul <vkoul@kernel.org>
Link: https://lore.kernel.org/r/20200622222747.717306-5-bjorn.andersson@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>

arm64: dts: qcom: sm8250: Add QMP AOSS node

Add a node for the QMP AOSS.

Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Vinod Koul <vkoul@kernel.org>
Link: https://lore.kernel.org/r/20200622222747.717306-4-bjorn.andersson@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>

arm64: dts: qcom: sm8250: Add IPCC

Add the IPCC node, used to send and receive IPC signals with
remoteprocs.

Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Vinod Koul <vkoul@kernel.org>
Link: https://lore.kernel.org/r/20200622222747.717306-3-bjorn.andersson@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>

arm64: dts: qcom: sm8250-mtp: Drop PM8150 ldo11

PM8150 ldo11 on the MTP is wired to VDD_SSC_CX and controlled in levels,
rather than as a regulator. As such it's available from the rpmhpd as
the SM8250_LCX power domain.

Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Vinod Koul <vkoul@kernel.org>
Fixes: ec13d5c23a33 ("arm64: dts: qcom: sm8250-mtp: Add pm8150, pm8150l and pm8009")
Link: https://lore.kernel.org/r/20200622222747.717306-2-bjorn.andersson@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>

arm64: dts: qcom: Add support for Sony Xperia 10/10 Plus (Ganges platform)

Add device tree support for the Sony Xperia 10 and 10
Plus smartphones. They are all based on the Sony Ganges
platform (sdm630/636) and share a lot of common code.
The differences are really minor, so a Ganges-common DTSI
has been created to reduce clutter.

10 - Kirin
10 Plus - Mermaid

This platform is based on SoMC Nile, but there are some
major differences when it comes to pin configuration and
panel setup (among others).

The boards currently support:
* Screen console
* SDHCI
* I2C
* pstore log dump
* GPIO keys
* PSCI idle states

Signed-off-by: Martin Botka <martin.botka1@gmail.com>
Signed-off-by: Konrad Dybcio <konradybcio@gmail.com>
Tested-by: Martin Botka <martin.botka1@gmail.com>
Link: https://lore.kernel.org/r/20200622192558.152828-7-konradybcio@gmail.com
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>

arm64: dts: qcom: Add support for Sony Xperia XA2/Plus/Ultra (Nile platform)

Add device tree support for the Sony Xperia XA2, XA2 Plus and
XA2 Ultra smartphones. They are all based on the Sony Nile
platform (sdm630) and share a lot of common code. The
differences are really minor, so a Nile-common DTSI
has been created to reduce clutter.

XA2 - Pioneer
XA2 Plus - Voyager
XA2 Ultra - Discovery

The boards currently support:
* Screen console
* SDHCI
* I2C
* pstore log dump
* GPIO keys
* PSCI idle states

Signed-off-by: Konrad Dybcio <konradybcio@gmail.com>
Tested-by: Łukasz Patron <priv.luk@gmail.com>
Link: https://lore.kernel.org/r/20200622192558.152828-6-konradybcio@gmail.com
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>

arm64: dts: qcom: sdm630: Add sdm630 dts file

Add devicetree files for SDM630 SoC and its pin configuration.
This commit adds basic nodes like cpu, psci and other required
configuration for booting up from eMMC to the serial console.

Signed-off-by: Konrad Dybcio <konradybcio@gmail.com>
Link: https://lore.kernel.org/r/20200622192558.152828-5-konradybcio@gmail.com
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>

arm64: dts: qcom: pm660(l): Add base dts files

Add base DTS files for pm660(l) along with GPIOs, power-on and
rtc nodes.

Signed-off-by: Konrad Dybcio <konradybcio@gmail.com>
Link: https://lore.kernel.org/r/20200622192558.152828-4-konradybcio@gmail.com
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>

arm64: dts: qcom: sm8250: add I2C and SPI nodes

Much like SDM845 each serial engine has 4 pins attached. Add all
possible I2C and SPI nodes for all 20 serial engines.

Tested-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20200606131300.3874987-1-dmitry.baryshkov@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>

arm64: dts: qcom: sm8250: Add TLMM pinctrl node

Add the TLMM pinctrl node for SM8250 and reserve pins 28-31 and 40-43 on
the MTP as firmware does not allow Linux to touch these pins.

Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Tested-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20200430181716.3797842-1-bjorn.andersson@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>

arm64: dts: qcom: pm8150x: add thermal alarms and thermal zones

Add temperature alarm and thermal zone configuration to all three
pm8150 instances. Configuration is largely based on the msm-4.19 tree.
These alarms use main adc of the pmic. Separate temperature adc is not
supported yet.

Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20200621192824.2069145-3-dmitry.baryshkov@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>

arm64: dts: qcom: sm8250-mtp: include pmic files

Include files describing used PMIC chips, GPIOs, power on, etc nodes.

Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20200621192824.2069145-2-dmitry.baryshkov@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>

arm64: dts: qcom: pm8009: Add base dts file

Add base DTS file for pm8009 along with GPIOs and power-on nodes.

Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20200621192824.2069145-1-dmitry.baryshkov@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>

arm64: dts: ipq8074: enable sdhci node

Enable mmc device found on ipq8074 devices

Signed-off-by: Sivaprakash Murugesan <sivaprak@codeaurora.org>
Link: https://lore.kernel.org/r/1591702511-18571-1-git-send-email-sivaprak@codeaurora.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>

arm64: dts: qcom: sm8150: Add USB and PHY device nodes

Add device nodes for the USB3 controller, QMP SS PHY and
SNPS HS PHY.

Signed-off-by: Jack Pham <jackp@codeaurora.org>
Signed-off-by: Wesley Cheng <wcheng@codeaurora.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Vinod Koul <vkoul@kernel.org>
Tested-by: Vinod Koul <vinod.koul@linaro.org>
Link: https://lore.kernel.org/r/1586566362-21450-3-git-send-email-wcheng@codeaurora.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>

arm64: dts: qcom: sm8150: Add thermal zones and throttling support

sm8150 has 27 thermal sensors split across two tsens controllers. Add
the thermal zones to expose them and wireup the cpus to throttle their
frequencies on crossing passive temperature thresholds.

Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org>
Link: https://lore.kernel.org/r/1cdbebe6f7f69ccd8468a4138b56e8a200289d95.1591684754.git.amit.kucheria@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>

dt-bindings: thermal: qcom-tsens: Add compatible for sm8150, sm8250

Added tsens bindings for sm8150 and sm8250

Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org>
Link: https://lore.kernel.org/r/c3361043e66139812bd4cd85b917659d85e1564f.1591684754.git.amit.kucheria@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>

arm64: dts: msm8916: Add interconnect provider DT nodes

Add nodes for the network-on-chip interconnect buses present on
MSM8916-based platforms.

Tested-by: Stephan Gerhold <stephan@gerhold.net>
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
Link: https://lore.kernel.org/r/20200617134515.25229-1-georgi.djakov@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>

arm64: dts: qcom: sc7180: Add WCN3990 WLAN module device node

Add device node for the ath10k SNOC platform driver probe
and add resources required for WCN3990 on sc7180 soc.

Signed-off-by: Rakesh Pillai <pillair@codeaurora.org>
Link: https://lore.kernel.org/r/1592668635-10894-1-git-send-email-pillair@codeaurora.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>

arm64: dts: qcom: sm8250: add watchdog device

Add on-SoC watchdog device node.

Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20200604004331.669936-7-dmitry.baryshkov@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>

arm64: dts: qcom: apq8016-sbc: Replace spaces with tabs

apq8016-sbc.dtsi uses spaces on some lines instead of tabs.
Make this consistent by converting them to tabs.

Also remove some redundant comments from the DAI link definitions
- this is already visible from the comment block before the "sound"
node or the device node entries itself.

Cc: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Link: https://lore.kernel.org/r/20200605185916.318494-4-stephan@gerhold.net
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>

arm64: dts: qcom: msm8916: Pull down PDM GPIOs during sleep

The original qcom kernel changed the PDM GPIOs to be pull-down
during sleep at some point. Reportedly this was done because
there was some "leakage at PDM outputs during sleep":

  https://source.codeaurora.org/quic/la/kernel/msm-3.10/commit/?id=0f87e08c1cd3e6484a6f7fb3e74e37340bdcdee0

I cannot say how effective this is, but everything seems to work
fine with this change so let's apply the same to mainline just
to be sure.

Cc: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Link: https://lore.kernel.org/r/20200605185916.318494-3-stephan@gerhold.net
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>

arm64: dts: qcom: msm8916: Replace invalid bias-pull-none property

msm8916-pins.dtsi specifies "bias-pull-none" for most of the audio
pin configurations. This was likely copied from the qcom kernel fork
where the same property was used for these audio pins.

However, "bias-pull-none" actually does not exist at all - not in
mainline and not in downstream. I can only guess that the original
intention was to configure "no pull", i.e. bias-disable.

Change it to that instead.

Fixes: 143bb9ad85b7 ("arm64: dts: qcom: add audio pinctrls")
Cc: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Link: https://lore.kernel.org/r/20200605185916.318494-2-stephan@gerhold.net
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>

arm64: dts: qcom: msm8916: Set #address-cells for lpass

As of commit 4ff028f6c108 ("ASoC: qcom: lpass-cpu: Make I2S SD lines
configurable"), lpass now supports children nodes to configure the
MI2S SD lines to use for one of the I2S ports. For example:

lpass@7708000 {
dai@3 {
reg = <MI2S_QUATERNARY>;
qcom,playback-sd-lines = <1>;
};
};

The "reg" property refers to the DAI number in this case,
so we need to set #address-cells and #size-cells appropriately
to avoid DTC warnings.

Cc: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Link: https://lore.kernel.org/r/20200605185916.318494-1-stephan@gerhold.net
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>

arm64: dts: qcom: lenovo630: Add Modem firmware files

By specifying the modem firmware files, we can boot the modem subsystem
which also gives us wifi.

Signed-off-by: Jeffrey Hugo <jeffrey.l.hugo@gmail.com>
Link: https://lore.kernel.org/r/20200528185341.4891-1-jeffrey.l.hugo@gmail.com
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>

arm64: dts: qcom: msm8998-clamshell: Fix label on l15 regulator

The label on the l15 regulator node does not follow the style of the
rest of the regulator nodes.  Luckily, no one has used the label yet,
so lets fix it.

Fixes: 2c6d2d3a580a ("arm64: dts: qcom: Add Lenovo Miix 630")
Signed-off-by: Jeffrey Hugo <jeffrey.l.hugo@gmail.com>
Link: https://lore.kernel.org/r/20200528145135.44269-1-jeffrey.l.hugo@gmail.com
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>

arm64: dts: qcom: msm8998-mtp: Fix label on l15 regulator

The label on the l15 regulator node does not follow the style of the
rest of the regulator nodes.  Luckily, no one has used the label yet,
so lets fix it.

Fixes: 31c1f0e33deb ("arm64: dts: qcom: msm8998: Add RPM and regulators for MTP")
Signed-off-by: Jeffrey Hugo <jeffrey.l.hugo@gmail.com>
Link: https://lore.kernel.org/r/20200528144814.44143-1-jeffrey.l.hugo@gmail.com
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>

arm64: dts: qcom: sc7180: Move mss node to the right place

The modem node has an address of 4080000 and thus should come after tlmm
and before gpu. Move the node to the right place to maintainer proper
address sort order.

Reviewed-by: Sibi Sankar <sibis@codeaurora.org>
Reviewed-by: Evan Green <evgreen@chromium.org>
Cc: Evan Green <evgreen@chromium.org>
Cc: Sibi Sankar <sibis@codeaurora.org>
Fixes: e14a15eba89a ("arm64: dts: qcom: sc7180: Add Q6V5 MSS node")
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/20200521010337.229177-1-swboyd@chromium.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>

arm64: dts: qcom: sm8250: change ufs node name to ufshc

The ufs-qcom driver checks that the name matches the androidboot.bootdevice
parameter provided by the bootloader, which uses the name ufshc. Without
this change UFS fails to probe.

I think this is broken behavior from the ufs-qcom driver, but using the
name ufshc is consistent with dts for sdm845/sm8150/etc.

Signed-off-by: Jonathan Marek <jonathan@marek.ca>
Link: https://lore.kernel.org/r/20200523175232.13721-1-jonathan@marek.ca
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>

arm64: dts: qcom: sm8250: sort nodes by physical address

Other dts have nodes sorted by physical address, be consistent with that.

Signed-off-by: Jonathan Marek <jonathan@marek.ca>
Link: https://lore.kernel.org/r/20200523132223.31108-1-jonathan@marek.ca
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>

arm64: dts: qcom: sm8250: rename spmi node to spmi_bus

The pm8150 dtsi files refer to it as spmi_bus, so change it.

Signed-off-by: Jonathan Marek <jonathan@marek.ca>
Link: https://lore.kernel.org/r/20200523132104.31046-1-jonathan@marek.ca
[bjorn: Dropped qcom, from node name while we're poking at it]
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>

arm64: dts: qcom: sm8250: use dt-bindings defines for clocks

Use the dt-bindings defines for qupv3_id_1 node's clocks.

Signed-off-by: Jonathan Marek <jonathan@marek.ca>
Link: https://lore.kernel.org/r/20200523131213.18653-1-jonathan@marek.ca
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>

Linux 5.8-rc1

Merge tag 'LSM-add-setgid-hook-5.8-author-fix' of git://github.com/micah-morton/linux

Pull SafeSetID update from Micah Morton:
 "Add additional LSM hooks for SafeSetID

  SafeSetID is capable of making allow/deny decisions for set*uid calls
  on a system, and we want to add similar functionality for set*gid
  calls.

  The work to do that is not yet complete, so probably won't make it in
  for v5.8, but we are looking to get this simple patch in for v5.8
  since we have it ready.

  We are planning on the rest of the work for extending the SafeSetID
  LSM being merged during the v5.9 merge window"

* tag 'LSM-add-setgid-hook-5.8-author-fix' of git://github.com/micah-morton/linux:
  security: Add LSM hooks to set*gid syscalls

security: Add LSM hooks to set*gid syscalls

The SafeSetID LSM uses the security_task_fix_setuid hook to filter
set*uid() syscalls according to its configured security policy. In
preparation for adding analagous support in the LSM for set*gid()
syscalls, we add the requisite hook here. Tested by putting print
statements in the security_task_fix_setgid hook and seeing them get hit
during kernel boot.

Signed-off-by: Thomas Cedeno <thomascedeno@google.com>
Signed-off-by: Micah Morton <mortonm@chromium.org>

Merge tag 'for-5.8-part2-tag' of git://git./linux/kernel/git/kdave/linux

Pull btrfs updates from David Sterba:
 "This reverts the direct io port to iomap infrastructure of btrfs
  merged in the first pull request. We found problems in invalidate page
  that don't seem to be fixable as regressions or without changing iomap
  code that would not affect other filesystems.

  There are four reverts in total, but three of them are followup
  cleanups needed to revert a43a67a2d715 cleanly. The result is the
  buffer head based implementation of direct io.

  Reverts are not great, but under current circumstances I don't see
  better options"

* tag 'for-5.8-part2-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux:
  Revert "btrfs: switch to iomap_dio_rw() for dio"
  Revert "fs: remove dio_end_io()"
  Revert "btrfs: remove BTRFS_INODE_READDIO_NEED_LOCK"
  Revert "btrfs: split btrfs_direct_IO to read and write part"

Merge git://git./linux/kernel/git/netdev/net

Pull networking fixes from David Miller:

 1) Fix cfg80211 deadlock, from Johannes Berg.

 2) RXRPC fails to send norigications, from David Howells.

 3) MPTCP RM_ADDR parsing has an off by one pointer error, fix from
    Geliang Tang.

 4) Fix crash when using MSG_PEEK with sockmap, from Anny Hu.

 5) The ucc_geth driver needs __netdev_watchdog_up exported, from
    Valentin Longchamp.

 6) Fix hashtable memory leak in dccp, from Wang Hai.

 7) Fix how nexthops are marked as FDB nexthops, from David Ahern.

 8) Fix mptcp races between shutdown and recvmsg, from Paolo Abeni.

 9) Fix crashes in tipc_disc_rcv(), from Tuong Lien.

10) Fix link speed reporting in iavf driver, from Brett Creeley.

11) When a channel is used for XSK and then reused again later for XSK,
    we forget to clear out the relevant data structures in mlx5 which
    causes all kinds of problems. Fix from Maxim Mikityanskiy.

12) Fix memory leak in genetlink, from Cong Wang.

13) Disallow sockmap attachments to UDP sockets, it simply won't work.
    From Lorenz Bauer.

* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (83 commits)
  net: ethernet: ti: ale: fix allmulti for nu type ale
  net: ethernet: ti: am65-cpsw-nuss: fix ale parameters init
  net: atm: Remove the error message according to the atomic context
  bpf: Undo internal BPF_PROBE_MEM in BPF insns dump
  libbpf: Support pre-initializing .bss global variables
  tools/bpftool: Fix skeleton codegen
  bpf: Fix memlock accounting for sock_hash
  bpf: sockmap: Don't attach programs to UDP sockets
  bpf: tcp: Recv() should return 0 when the peer socket is closed
  ibmvnic: Flush existing work items before device removal
  genetlink: clean up family attributes allocations
  net: ipa: header pad field only valid for AP->modem endpoint
  net: ipa: program upper nibbles of sequencer type
  net: ipa: fix modem LAN RX endpoint id
  net: ipa: program metadata mask differently
  ionic: add pcie_print_link_status
  rxrpc: Fix race between incoming ACK parser and retransmitter
  net/mlx5: E-Switch, Fix some error pointer dereferences
  net/mlx5: Don't fail driver on failure to create debugfs
  net/mlx5e: CT: Fix ipv6 nat header rewrite actions
  ...

Revert "btrfs: switch to iomap_dio_rw() for dio"

This reverts commit a43a67a2d715540c1368b9501a22b0373b5874c0.

This patch reverts the main part of switching direct io implementation
to iomap infrastructure. There's a problem in invalidate page that
couldn't be solved as regression in this development cycle.

The problem occurs when buffered and direct io are mixed, and the ranges
overlap. Although this is not recommended, filesystems implement
measures or fallbacks to make it somehow work. In this case, fallback to
buffered IO would be an option for btrfs (this already happens when
direct io is done on compressed data), but the change would be needed in
the iomap code, bringing new semantics to other filesystems.

Another problem arises when again the buffered and direct ios are mixed,
invalidation fails, then -EIO is set on the mapping and fsync will fail,
though there's no real error.

There have been discussions how to fix that, but revert seems to be the
least intrusive option.

Link: https://lore.kernel.org/linux-btrfs/20200528192103.xm45qoxqmkw7i5yl@fiona/
Signed-off-by: David Sterba <dsterba@suse.com>

net: ethernet: ti: ale: fix allmulti for nu type ale

On AM65xx MCU CPSW2G NUSS and 66AK2E/L NUSS allmulti setting does not allow
unregistered mcast packets to pass.

This happens, because ALE VLAN entries on these SoCs do not contain port
masks for reg/unreg mcast packets, but instead store indexes of
ALE_VLAN_MASK_MUXx_REG registers which intended for store port masks for
reg/unreg mcast packets.
This path was missed by commit 9d1f6447274f ("net: ethernet: ti: ale: fix
seeing unreg mcast packets with promisc and allmulti disabled").

Hence, fix it by taking into account ALE type in cpsw_ale_set_allmulti().

Fixes: 9d1f6447274f ("net: ethernet: ti: ale: fix seeing unreg mcast packets with promisc and allmulti disabled")
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: ethernet: ti: am65-cpsw-nuss: fix ale parameters init

The ALE parameters structure is created on stack, so it has to be reset
before passing to cpsw_ale_create() to avoid garbage values.

Fixes: 93a76530316a ("net: ethernet: ti: introduce am65x/j721e gigabit eth subsystem driver")
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge git://git./pub/scm/linux/kernel/git/bpf/bpf

Alexei Starovoitov says:

====================
pull-request: bpf 2020-06-12

The following pull-request contains BPF updates for your *net* tree.

We've added 26 non-merge commits during the last 10 day(s) which contain
a total of 27 files changed, 348 insertions(+), 93 deletions(-).

The main changes are:

1) sock_hash accounting fix, from Andrey.

2) libbpf fix and probe_mem sanitizing, from Andrii.

3) sock_hash fixes, from Jakub.

4) devmap_val fix, from Jesper.

5) load_bytes_relative fix, from YiFei.
====================

Signed-off-by: David S. Miller <davem@davemloft.net>

net: atm: Remove the error message according to the atomic context

Looking into the context (atomic!) and the error message should be dropped.

Signed-off-by: Liao Pingfang <liao.pingfang@zte.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge tag '5.8-rc-smb3-fixes-part2' of git://git.samba.org/sfrench/cifs-2.6

Pull more cifs updates from Steve French:
 "12 cifs/smb3 fixes, 2 for stable.

   - add support for idsfromsid on create and chgrp/chown allowing
     ability to save owner information more naturally for some workloads

   - improve query info (getattr) when SMB3.1.1 posix extensions are
     negotiated by using new query info level"

* tag '5.8-rc-smb3-fixes-part2' of git://git.samba.org/sfrench/cifs-2.6:
  smb3: Add debug message for new file creation with idsfromsid mount option
  cifs: fix chown and chgrp when idsfromsid mount option enabled
  smb3: allow uid and gid owners to be set on create with idsfromsid mount option
  smb311: Add tracepoints for new compound posix query info
  smb311: add support for using info level for posix extensions query
  smb311: Add support for lookup with posix extensions query info
  smb311: Add support for SMB311 query info (non-compounded)
  SMB311: Add support for query info using posix extensions (level 100)
  smb3: add indatalen that can be a non-zero value to calculation of credit charge in smb2 ioctl
  smb3: fix typo in mount options displayed in /proc/mounts
  cifs: Add get_security_type_str function to return sec type.
  smb3: extend fscache mount volume coherency check

binderfs: add gitignore for generated sample program

Let's keep "git status" happy and quiet.

Fixes: 9762dc1432e1 ("samples: add binderfs sample program
Fixes: fca5e94921d5 ("samples: binderfs: really compile this sample and fix build issues")
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

doc: don't use deprecated "---help---" markers in target docs

I'm not convinced the script makes useful automaed help lines anyway,
but since we're trying to deprecate the use of "---help---" in Kconfig
files, let's fix the doc example code too.

See commit a7f7f6248d97 ("treewide: replace '---help---' in Kconfig
files with 'help'")

Cc: Masahiro Yamada <masahiroy@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Merge tag 'kbuild-v5.8-2' of git://git./linux/kernel/git/masahiroy/linux-kbuild

Pull more Kbuild updates from Masahiro Yamada:

 - fix build rules in binderfs sample

 - fix build errors when Kbuild recurses to the top Makefile

 - covert '---help---' in Kconfig to 'help'

* tag 'kbuild-v5.8-2' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild:
  treewide: replace '---help---' in Kconfig files with 'help'
  kbuild: fix broken builds because of GZIP,BZIP2,LZOP variables
  samples: binderfs: really compile this sample and fix build issues

Merge tag 'scsi-misc' of git://git./linux/kernel/git/jejb/scsi

Pull more SCSI updates from James Bottomley:
 "This is the set of changes collected since just before the merge
  window opened. It's mostly minor fixes in drivers.

  The one non-driver set is the three optical disk (sr) changes where
  two are error path fixes and one is a helper conversion.

  The big driver change is the hpsa compat_alloc_userspace rework by Al
  so he can kill the remaining user. This has been tested and acked by
  the maintainer"

* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (21 commits)
  scsi: acornscsi: Fix an error handling path in acornscsi_probe()
  scsi: storvsc: Remove memset before memory freeing in storvsc_suspend()
  scsi: cxlflash: Remove an unnecessary NULL check
  scsi: ibmvscsi: Don't send host info in adapter info MAD after LPM
  scsi: sr: Fix sr_probe() missing deallocate of device minor
  scsi: sr: Fix sr_probe() missing mutex_destroy
  scsi: st: Convert convert get_user_pages() --> pin_user_pages()
  scsi: target: Rename target_setup_cmd_from_cdb() to target_cmd_parse_cdb()
  scsi: target: Fix NULL pointer dereference
  scsi: target: Initialize LUN in transport_init_se_cmd()
  scsi: target: Factor out a new helper, target_cmd_init_cdb()
  scsi: hpsa: hpsa_ioctl(): Tidy up a bit
  scsi: hpsa: Get rid of compat_alloc_user_space()
  scsi: hpsa: Don't bother with vmalloc for BIG_IOCTL_Command_struct
  scsi: hpsa: Lift {BIG_,}IOCTL_Command_struct copy{in,out} into hpsa_ioctl()
  scsi: ufs: Remove redundant urgent_bkop_lvl initialization
  scsi: ufs: Don't update urgent bkops level when toggling auto bkops
  scsi: qedf: Remove redundant initialization of variable rc
  scsi: mpt3sas: Fix memset() in non-RDPQ mode
  scsi: iscsi: Fix reference count leak in iscsi_boot_create_kobj
  ...

Merge branch 'i2c/for-5.8' of git://git./linux/kernel/git/wsa/linux

Pull i2c updates from Wolfram Sang:
 "I2C has quite some patches for you this time. I hope it is the move to
  per-driver-maintainers which is now showing results. We will see.

  The big news is two new drivers (Nuvoton NPCM and Qualcomm CCI),
  larger refactoring of the Designware, Tegra, and PXA drivers, the
  Cadence driver supports being a slave now, and there is support to
  instanciate SPD eeproms for well-known cases (which will be
  user-visible because the i801 driver supports it), and some
  devm_platform_ioremap_resource() conversions which blow up the
  diffstat.

  Note that I applied the Nuvoton driver quite late, so some minor fixup
  patches arrived during the merge window. I chose to apply them right
  away because they were trivial"

* 'i2c/for-5.8' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (109 commits)
  i2c: Drop stray comma in MODULE_AUTHOR statements
  i2c: npcm7xx: npcm_i2caddr[] can be static
  MAINTAINERS: npcm7xx: Add maintainer for Nuvoton NPCM BMC
  i2c: npcm7xx: Fix a couple of error codes in probe
  i2c: icy: Fix build with CONFIG_AMIGA_PCMCIA=n
  i2c: npcm7xx: Remove unnecessary parentheses
  i2c: npcm7xx: Add support for slave mode for Nuvoton
  i2c: npcm7xx: Add Nuvoton NPCM I2C controller driver
  dt-bindings: i2c: npcm7xx: add NPCM I2C controller
  i2c: pxa: don't error out if there's no pinctrl
  i2c: add 'single-master' property to generic bindings
  i2c: designware: Add Baikal-T1 System I2C support
  i2c: designware: Move reg-space remapping into a dedicated function
  i2c: designware: Retrieve quirk flags as early as possible
  i2c: designware: Convert driver to using regmap API
  i2c: designware: Discard Cherry Trail model flag
  i2c: designware: Add Baytrail sem config DW I2C platform dependency
  i2c: designware: slave: Set DW I2C core module dependency
  i2c: designware: Use `-y` to build multi-object modules
  dt-bindings: i2c: dw: Add Baikal-T1 SoC I2C controller
  ...

Merge tag 'media/v5.8-2' of git://git./linux/kernel/git/mchehab/linux-media

Pull more media updates from Mauro Carvalho Chehab:

 - a set of atomisp patches. They remove several abstraction layers, and
   fixes clang and gcc warnings (that were hidden via some macros that
   were disabling 4 or 5 types of warnings there). There are also some
   important fixes and sensor auto-detection on newer BIOSes via ACPI
   _DCM tables.

 - some fixes

* tag 'media/v5.8-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (95 commits)
  media: rkvdec: Fix H264 scaling list order
  media: v4l2-ctrls: Unset correct HEVC loop filter flag
  media: videobuf2-dma-contig: fix bad kfree in vb2_dma_contig_clear_max_seg_size
  media: v4l2-subdev.rst: correct information about v4l2 events
  media: s5p-mfc: Properly handle dma_parms for the allocated devices
  media: medium: cec: Make MEDIA_CEC_SUPPORT default to n if !MEDIA_SUPPORT
  media: cedrus: Implement runtime PM
  media: cedrus: Program output format during each run
  media: atomisp: improve ACPI/DMI detection logs
  media: Revert "media: atomisp: add Asus Transform T101HA ACPI vars"
  media: Revert "media: atomisp: Add some ACPI detection info"
  media: atomisp: improve sensor detection code to use _DSM table
  media: atomisp: get rid of an iomem abstraction layer
  media: atomisp: get rid of a string_support.h abstraction layer
  media: atomisp: use strscpy() instead of less secure variants
  media: atomisp: set DFS to MAX if sensor doesn't report fps
  media: atomisp: use different dfs failed messages
  media: atomisp: change the detection of ISP2401 at runtime
  media: atomisp: use macros from intel-family.h
  media: atomisp: don't set hpll_freq twice with different values
  ...

Merge tag 'libnvdimm-for-5.8' of git://git./linux/kernel/git/nvdimm/nvdimm

Pull libnvdimm updates from Dan Williams:
 "Small collection of cleanups to rework usage of ->queuedata and the
  GUID api"

* tag 'libnvdimm-for-5.8' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm:
  nvdimm/pmem: stop using ->queuedata
  nvdimm/btt: stop using ->queuedata
  nvdimm/blk: stop using ->queuedata
  libnvdimm: Replace guid_copy() with import_guid() where it makes sense

watch_queue: add gitignore for generated sample program

Let's keep "git status" happy and quiet.

Fixes: f5b5a164f9a1 ("Add sample notification program")
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Merge tag 'iomap-5.8-merge-1' of git://git./fs/xfs/xfs-linux

Pull iomap fix from Darrick Wong:
 "A single iomap bug fix for a variable type mistake on 32-bit
  architectures, fixing an integer overflow problem in the unshare
  actor"

* tag 'iomap-5.8-merge-1' of git://git.kernel.org/pub/scm/fs/xfs/xfs-linux:
  iomap: Fix unsharing of an extent >2GB on a 32-bit machine

Merge tag 'xfs-5.8-merge-9' of git://git./fs/xfs/xfs-linux

Pull xfs fix from Darrick Wong:
 "We've settled down into the bugfix phase; this one fixes a resource
  leak on an error bailout path"

* tag 'xfs-5.8-merge-9' of git://git.kernel.org/pub/scm/fs/xfs/xfs-linux:
  xfs: Add the missed xfs_perag_put() for xfs_ifree_cluster()