Arnd Bergmann [Fri, 13 Oct 2023 20:46:42 +0000 (22:46 +0200)]
Merge tag 'renesas-dts-for-v6.7-tag2' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-devel into soc/dt
Renesas DTS updates for v6.7 (take two)
- Improve audio clock accuracy on the RZ/{G2L,G2LC,V2L} SMARC EVK
development boards,
- Add FLASH support for the Renesas Bock-W development board,
- Add L2 cache and non-coherent DMA support on the RZ/Five SoC and the
RZ/Five SMARC development board,
- Add initial support for the RZ/G3S SoC and the RZ/G3S SMARC SoM and
SMARC Carrier-II EVK development boards,
- Add initial support for the R8A779F4 variant of the R-Car S4-8 SoC
and the R-Car S4 Starter Kit development board,
- Apply DT overlays to base DTBs to improve validation and usability.
* tag 'renesas-dts-for-v6.7-tag2' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-devel: (25 commits)
arm64: dts: renesas: Apply overlays to base dtbs
arm64: dts: renesas: rzg3s-smarc-som: Spelling s/device-type/device_type/
arm64: dts: renesas: r9a08g045: Add missing cache-level for L3 cache
arm64: dts: renesas: r9a08g045: Add nodes for SDHI1 and SDHI2
arm64: dts: renesas: ebisu: Document Ebisu-4D support
arm64: dts: renesas: Add R-Car S4 Starter Kit support
arm64: dts: renesas: Add Renesas R8A779F4 SoC support
arm64: dts: renesas: Add initial device tree for RZ/G3S SMARC EVK board
arm64: dts: renesas: Add initial device tree for RZ SMARC Carrier-II Board
arm64: dts: renesas: Add initial support for RZ/G3S SMARC SoM
arm64: dts: renesas: Add initial DTSI for RZ/G3S SoC
riscv: dts: renesas: rzfive-smarc: Enable the blocks which were explicitly disabled
riscv: dts: renesas: r9a07g043f: Add dma-noncoherent property
riscv: dts: renesas: r9a07g043f: Add L2 cache node
ARM: dts: renesas: bockw: Add FLASH node
arm64: dts: renesas: rz-smarc: Use versa3 clk for audio mclk
dt-bindings: clock: renesas,rzg2l-cpg: Document RZ/G3S SoC
clk: tegra: fix error return case for recalc_rate
clk: si521xx: Fix regmap write accessor
clk: si521xx: Use REGCACHE_FLAT instead of NONE
...
Arnd Bergmann [Fri, 13 Oct 2023 20:44:56 +0000 (22:44 +0200)]
Merge tag 'renesas-dt-bindings-for-v6.7-tag2' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-devel into soc/dt
Renesas DT binding updates for v6.7 (take two)
- Document support for the Renesas RZ/G3S SMARC SoM and SMARC
Carrier-II EVK development boards,
- Document support for the Renesas R-Car S4 Starter Kit.
* tag 'renesas-dt-bindings-for-v6.7-tag2' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-devel:
dt-bindings: soc: renesas: Document R-Car S4 Starter Kit
dt-bindings: soc: renesas: Document SMARC Carrier-II EVK
dt-bindings: soc: renesas: Document RZ/G3S SMARC SoM
Arnd Bergmann [Fri, 13 Oct 2023 20:44:11 +0000 (22:44 +0200)]
Merge tag 'sti-dt-for-v6.7-round1' of git://git.kernel.org/pub/scm/linux/kernel/git/pchotard/sti into soc/dt
STi DT for v6.7, round 1 :
stih418-b2264: leds and serial fixes
stih407: drop max-duty-cycle property
stih415/416: remove boards from yaml
stih407/410/418: add boards to yaml
* tag 'sti-dt-for-v6.7-round1' of git://git.kernel.org/pub/scm/linux/kernel/git/pchotard/sti:
dt-bindings: arm: sti: add STi boards and remove stih415/stih416
dt-bindings: soc: sti: add STi platform syscon
ARM: dts: st: correct led level in stih418-b2264.dts
ARM: dts: st: move leds out of soc in stih418-b2264.dts
ARM: dts: st: correct serial alias in stih418-b2264.dts
ARM: dts: st: stih407: drop max-duty-cycle
Arnd Bergmann [Fri, 13 Oct 2023 20:43:09 +0000 (22:43 +0200)]
Merge tag 'omap-for-v6.7/dt-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into soc/dt
Devicetree changes for omaps for v6.7 merge window
Two non-urgent devicetree fixes for am371-evm led pinmux and a node name
warning fix for omap4-epson-embt2ws, and updates for connected devices for
various devices:
- Device updates and enabling of pru support for am335x-pocketbeagle
- Few more devices such as leds and iio for omap4-epson-embt2ws
- Ethernet and led updates for am3517-evm
- Modem sleep pins configuration for motorola-mapphone
* tag 'omap-for-v6.7/dt-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: omap4-embt2ws: Fix pinctrl single node name warning
ARM: dts: motorola-mapphone: Add mdm6600 sleep pins
ARM: dts: am3517: Configure ethernet alias
ARM: dts: am3517-evm: Enable Ethernet PHY Interrupt
ARM: dts: am3517-evm: Fix LED3/4 pinmux
ARM: dts: omap3-gta04: Drop superfluous omap36xx compatible
ARM: dts: omap: omap4-embt2ws: Add IMU at control unit
ARM: dts: omap: omap4-embt2ws: Let IMU driver handle Magnetometer internally
ARM: dts: am335x-pocketbeagle: add missing GPIO mux
ARM: dts: am335x-pocketbeagle: enable pru
ARM: dts: am335x-pocketbeagle: remove dependency cycle
ARM: dts: am335x-pocketbeagle: update LED information
ARM: dts: omap4: embt2ws: add LED
Arnd Bergmann [Fri, 13 Oct 2023 20:42:04 +0000 (22:42 +0200)]
Merge tag 'at91-dt-6.7' of https://git.kernel.org/pub/scm/linux/kernel/git/at91/linux into soc/dt
Microchip AT91 device tree updates for 6.7
It contains:
- the new Microchip SAMA5D29 Curiosity board
- a typo fix in TDES node name for SAMA5D4 dtsi
- enablement of RTT as RTC for SAM9X60 Curiosity board
* tag 'at91-dt-6.7' of https://git.kernel.org/pub/scm/linux/kernel/git/at91/linux:
ARM: dts: at91: sam9x60_curiosity: Add mandatory dt property for RTT
ARM: dts: at91: sama5d29_curiosity: Add device tree for sama5d29_curiosity board
dt-bindings: ARM: at91: Document Microchip SAMA5D29 Curiosity
ARM: dts: at91/trivial: fix typo in crypto DT naming
Arnd Bergmann [Fri, 13 Oct 2023 20:41:10 +0000 (22:41 +0200)]
Merge tag 'ixp4xx-for-soc-v6.7' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-nomadik into soc/dt
Some IXP4xx updates for the v6.7 kernel cycle:
- Provide proper bindings including missing vendor prefixes
for the device trees in use and one more new vendor.
- Add a device tree for USRobotics USR8200 which has two
active users.
- Augment the "reset" GPIO buttons to send KEY_RESTART as
appropriate.
- Enable write on the NSLU2 flash so we get a writeable
rootfs on this device.
* tag 'ixp4xx-for-soc-v6.7' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-nomadik:
ARM: dts: ixp4xx: Use right restart keycode
ARM: dts: ixp4xx-nslu2: Enable write on flash
ARM: dts: ixp4xx: Add USRobotics USR8200 device tree
ARM: dts: Use only the Linksys compatible for now
dt-bindings: arm: List more IXP4xx devices
dt-bindings: Add vendor prefixes
Arnd Bergmann [Fri, 13 Oct 2023 20:29:07 +0000 (22:29 +0200)]
Merge tag 'samsung-dt-6.7' of https://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux into soc/dt
Samsung DTS ARM changes for v6.7
1. Switch all sound cards to generic audio-routing property, supported
since previous release for Samsung drivers. The old
samsung,audio-routing property is deprecated.
2. Correct Exynos4210 thermal by using polling. Apparently interrupts in
Thermal Monitoring Unit are broken.
* tag 'samsung-dt-6.7' of https://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux:
ARM: dts: samsung: exynos4210: enable polling
ARM: dts: samsung: s5pv210-galaxys: switch sound card to audio-routing
ARM: dts: samsung: s5pv210-fascinate4g: switch sound card to audio-routing
ARM: dts: samsung: exynos5422-odroid: switch sound card to audio-routing
ARM: dts: samsung: exynos4412-odroid: switch sound card to audio-routing
ARM: dts: samsung: exynos4412-n710x: switch sound card to audio-routing
ARM: dts: samsung: exynos4412-galaxy-s3: switch sound card to audio-routing
ARM: dts: samsung: exynos4212-tab3: switch sound card to audio-routing
ARM: dts: st: correct serial alias in stih418-b2264.dts
Aliases should only contain lowercase, digits or - hence
correct the alias for the serial from ttyAS0 into serial0
as already done for the other boards.
arch/arm64/boot/dts/renesas/r9a08g045s33-smarc.dt: /: memory@48000000: 'device-type' does not match any of the regexes: 'pinctrl-[0-9]+'
from schema $id: http://devicetree.org/schemas/memory.yaml#
arch/arm64/boot/dts/renesas/r9a08g045s33-smarc.dtb: /: memory@48000000: 'device_type' is a required property
from schema $id: http://devicetree.org/schemas/memory.yaml#
Claudiu Beznea [Tue, 10 Oct 2023 13:27:01 +0000 (16:27 +0300)]
arm64: dts: renesas: r9a08g045: Add missing cache-level for L3 cache
Fix the following DTBS check warnings:
arch/arm64/boot/dts/renesas/r9a08g045s33-smarc.dtb: cache-controller-0: 'cache-level' is a required property
from schema $id: http://devicetree.org/schemas/cache.yaml#
arch/arm64/boot/dts/renesas/r9a08g045s33-smarc.dtb: cache-controller-0: 'cache-level' is a required property
from schema $id: http://devicetree.org/schemas/cache.yaml#
arch/arm64/boot/dts/renesas/r9a08g045s33-smarc.dtb: cache-controller-0: Unevaluated properties are not allowed ('cache-size', 'cache-unified' were unexpected)
from schema $id: http://devicetree.org/schemas/cache.yaml#
Arnd Bergmann [Thu, 12 Oct 2023 10:57:06 +0000 (12:57 +0200)]
Merge tag 'samsung-dt64-6.7' of https://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux into soc/dt
Samsung DTS ARM64 changes for v6.7
1. Exynos850: Add support for USB 2.0 (host and device) and enable it on
E850-96 board.
2. Exynos5433: Switch sound card to generic audio-routing property,
supported since previous release for Samsung drivers. The old
samsung,audio-routing property is deprecated.
3. Few cleanups.
* tag 'samsung-dt64-6.7' of https://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux:
arm64: dts: exynos: remove unused TMU alias
arm64: dts: exynos: Use pinctrl macros for exynos5433-tm2
arm64: dts: exynos: exynos5433-tm2: switch sound card to audio-routing
arm64: dts: exynos: Enable USB support on E850-96 board
arm64: dts: exynos: Enable USB in Exynos850
Arnd Bergmann [Thu, 12 Oct 2023 10:56:19 +0000 (12:56 +0200)]
Merge tag 'dt-cleanup-6.7' of https://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux-dt into soc/dt
Minor improvements in ARM DTS for v6.7
Few cleanups and improvements: split joined reg entries for Ethernet in
omap3-devkit8000, add missing spaces before '{' (MediaTek, Nuvoton) and
cleanup whitespace around '=' (MediaTek).
* tag 'dt-cleanup-6.7' of https://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux-dt:
ARM: dts: nuvoton: add missing space before {
ARM: dts: mediatek: minor whitespace cleanup around '='
ARM: dts: mediatek: add missing space before {
ARM: dts: omap3-devkit8000: correct ethernet reg addresses (split)
Arnd Bergmann [Thu, 12 Oct 2023 10:53:31 +0000 (12:53 +0200)]
Merge tag 'dt64-cleanup-6.7' of https://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux-dt into soc/dt
Minor improvements in ARM64 DTS for v6.7
Few cleanups and improvements: use lowercase hex for unit addresses
(Bitmain), add missing spaces before '{' (APM, MediaTek) and cleanup
whitespace around '=' (MediaTek, Marvell).
* tag 'dt64-cleanup-6.7' of https://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux-dt:
arm64: dts: marvell: minor whitespace cleanup around '='
arm64: dts: mediatek: minor whitespace cleanup around '='
arm64: dts: mediatek: add missing space before {
arm64: dts: apm: add missing space before {
arm64: dts: bitmain: lowercase unit addresses
Arnd Bergmann [Thu, 12 Oct 2023 10:37:31 +0000 (12:37 +0200)]
Merge tag 'renesas-dts-for-v6.7-tag1' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-devel into soc/dt
Renesas DTS updates for v6.7
- Add PCIe Host and Endpoint support for the R-Car S4-8 SoC and the
Renesas Spider development board,
- Add FLASH support for the Renesas Genmai and RSK+RZA1 development
boards,
- Add multi Component sound support for Renesas ULCB development
boards equipped with the Shimafuji Kingfisher extension,
- Miscellaneous fixes and improvements.
* tag 'renesas-dts-for-v6.7-tag1' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-devel:
arm64: dts: renesas: ulcb/kf: Use multi Component sound
ARM: dts: renesas: rskrza1: Add FLASH nodes
ARM: dts: renesas: genmai: Add FLASH nodes
ARM: dts: renesas: wheat: Move Ethernet node to LBSC
ARM: dts: renesas: blanche: Move Ethernet node to LBSC
ARM: dts: renesas: marzen: Move Ethernet node to LBSC
ARM: dts: renesas: r8a7792: Add LBSC node
ARM: dts: renesas: r8a7779: Add LBSC node
ARM: dts: renesas: r7s72100: Add BSC node
ARM: dts: renesas: Remove unused LBSC nodes from board DTS
arm64: dts: renesas: r8a779f0: spider: Enable PCIe Host ch0
arm64: dts: renesas: r8a779f0: Add PCIe Host and Endpoint nodes
ARM: dts: renesas: gr-peach: Remove unneeded probe-type property
ARM: dts: renesas: ape6evm: Drop bogus "mtd-rom" compatible value
ARM: dts: renesas: blanche: Fix typo in GP_11_2 pin name
arm64: dts: renesas: Handle ADG bit for sound clk_i
Maxim Schwalm [Mon, 7 Aug 2023 14:35:11 +0000 (17:35 +0300)]
ARM: tegra: Drop unit-address from parallel RGB output port
Fix the following W=1 build warning:
"Warning (unit_address_vs_reg): /host1x@50000000/dc@54200000/rgb/port@0:
node has a unit name, but no reg or ranges property"
dt-bindings: arm: tegra: pmc: Restructure pad configuration node schema
The pad configuration node schema in its current form can accidentally
match other properties as well. Restructure the schema to better match
how the device trees are using these.
Reviewed-by: Rob Herring <robh@kernel.org> Signed-off-by: Thierry Reding <treding@nvidia.com>
For indented subschemas it can be difficult to understand which block an
additionalProperties property belongs to. Moving it closer to the
beginning of a block is a good way to clarify this.
Reviewed-by: Rob Herring <robh@kernel.org> Signed-off-by: Thierry Reding <treding@nvidia.com>
Reformat the description of various properties to make them more
consistent with existing ones. Make use of json-schema's ability to
provide a description for individual list items to make improve the
documentation further.
Reviewed-by: Rob Herring <robh@kernel.org> Signed-off-by: Thierry Reding <treding@nvidia.com>
The "reset" key on a few IXP4xx routers were sending KEY_ESC
but what we want to send is KEY_RESTART which will make
OpenWrt and similar userspace do a controlled reboot.
Linus Walleij [Sat, 7 Oct 2023 12:15:11 +0000 (14:15 +0200)]
dt-bindings: Add vendor prefixes
These vendor prefixes are used by some routers supported
by e.g. OpenWrt.
- ADI Engineering is a US telecom equipment company.
- Arcom Controllers is a US manufacturer of repeaters.
- Freecom Gmbh is a german telecom equipment company.
- Gemtek Technology is a Taiwan telecom company.
- Gateway Communications was a telecommunication company,
now acquired by HKT Limited/PCCW.
- Goramo Gorecki is a privately owned Polish telecom
company.
- U.S. Robotics Corporation, known through their brand name
USRobotics is generally referred to as "USR" so use this
prefix for the company's device tree bindings.
Tony Lindgren [Sat, 7 Oct 2023 07:32:46 +0000 (10:32 +0300)]
ARM: dts: omap4-embt2ws: Fix pinctrl single node name warning
Looks like one pinctrl single binding warning sneaked in while we were
implementing the yaml binding. Let's fix the 'pinmux-wl12xx-gpio' does not
match any of the regexes warning by adding -pins suffix.
The sleep pins never got added earlier probably because the driver was not
behaving correctly with the sleep pins. We need the sleep pins to prevent
the modem from waking up on it's own if the reset pin glitches in deeper
SoC idle states.
Cc: Ivaylo Dimitrov <ivo.g.dimitrov.75@gmail.com> Cc: Merlijn Wajer <merlijn@wizzup.org> Cc: Pavel Machek <pavel@ucw.cz> Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Message-ID: <20230911035828.36984-1-tony@atomide.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
Adam Ford [Thu, 5 Oct 2023 00:04:01 +0000 (19:04 -0500)]
ARM: dts: am3517-evm: Fix LED3/4 pinmux
The pinmux for LED3 and LED4 are incorrectly attached to the
omap3_pmx_core when they should be connected to the omap3_pmx_wkup
pin mux. This was likely masked by the fact that the bootloader
used to do all the pinmuxing.
Fixes: 0dbf99542caf ("ARM: dts: am3517-evm: Add User LEDs and Pushbutton") Signed-off-by: Adam Ford <aford173@gmail.com>
Message-ID: <20231005000402.50879-1-aford173@gmail.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
Andreas Kemnade [Wed, 4 Oct 2023 06:53:23 +0000 (08:53 +0200)]
ARM: dts: omap3-gta04: Drop superfluous omap36xx compatible
Drop omap36xx compatible as done in other omap3630 devices.
This has apparently fallen through the lattice.
Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
Message-ID: <20231004065323.2408615-1-andreas@kemnade.info> Signed-off-by: Tony Lindgren <tony@atomide.com>
Andreas Kemnade [Wed, 27 Sep 2023 17:32:45 +0000 (19:32 +0200)]
ARM: dts: omap: omap4-embt2ws: Add IMU at control unit
Add also the level-shifter flag to avoid probe failure in magnetometer
probe.
Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
Message-ID: <20230927173245.2151083-4-andreas@kemnade.info> Signed-off-by: Tony Lindgren <tony@atomide.com>
arm64: dts: renesas: Add initial support for RZ/G3S SMARC SoM
Add initial support for the RZ/G3S SMARC SoM. The following devices
available on the SoM are added to this initial device tree:
- RZ/G3S SoC: Renesas R9A08G045S33GBG
- Clock Generator (only 24MHz output): Renesas 5L35023B
- 1GiB LPDDR4 SDRAM: Micron MT53D512M16D1DS-046
- 64GB eMMC Flash (though SD ch0): Micron MTFC64GBCAQTC
SD channel 0 of RZ/G3S is connected to an uSD card interface and an
eMMC. The selection b/w them is done through a hardware switch. The DT
will select b/w uSD and eMMC through the SW_SD0_DEV_SEL build flag.
arm64: dts: renesas: Add initial DTSI for RZ/G3S SoC
Add the initial DTSI for the RZ/G3S SoC.
The files in this commit have the following meaning:
- r9a08g045.dtsi: RZ/G3S family SoC common parts
- r9a08g045s33.dtsi: RZ/G3S R0A08G045S33 SoC specific parts
riscv: dts: renesas: rzfive-smarc: Enable the blocks which were explicitly disabled
Now that noncoherent dma support for the RZ/Five SoC has been added, enable
the IP blocks which were disabled on the RZ/Five SMARC. This adds
support for the below peripherals:
* Ethernet
* DMAC
* SDHI
* USB
* RSPI
* SSI
Add a device node for the Spansion S29GL512P NOR FLASH on the Bock-W
development board. This FLASH resides in the external address space of
the Local Bus State Controller.
Biju Das [Fri, 25 Aug 2023 09:05:18 +0000 (10:05 +0100)]
arm64: dts: renesas: rz-smarc: Use versa3 clk for audio mclk
Currently audio mclk uses a fixed clk of 11.2896MHz (multiple of 44.1kHz).
Replace this fixed clk with the programmable versa3 clk that can provide
the clocking to support both 44.1kHz (with a clock of 11.2896MHz) and
48kHz (with a clock of 12.2880MHz), based on audio sampling rate for
playback and record.
Merge tag 'clk-fixes-for-linus' of https://git.kernel.org/pub/scm/linux/kernel/git/clk/linux into renesas-dts-for-v6.7
Adding versa3 clock generator nodes to DTS depends on the fixed clock
index handling:
- Fix the binding for versaclock3 that was introduced this merge window
so we know what the values are for clk consumers
Document the Renesas SMARC Carrier-II EVK board which is based on the
Renesas RZ/G3S SMARC SoM. The SMARC Carrier-II EVK consists of an
RZ/G3S SoM module and a SMARC Carrier-II carrier board; the SoM module
sits on top of the carrier board.
Add documentation for the RZ/G3S CPG. The RZ/G3S CPG module is almost
identical to the one available in RZ/G2{L,UL}, the exception being some
core clocks as follows:
- The SD clock is composed of a mux and a divider, and the divider
has some limitations (div = 1 cannot be set if mux rate is 800MHz),
- There are 3 SD clocks,
- The OCTA and TSU clocks are specific to RZ/G3S,
- PLL1/4/6 are specific to RZ/G3S with its own computation formula.
Even with this RZ/G3S could use the same bindings as RZ/G2L.
Along with documentation bindings for the RZ/G3S (R9A08G045) Clock Pulse
Generator (CPG) core clocks, module clocks and resets were added.
ARM: dts: at91: sam9x60_curiosity: Add mandatory dt property for RTT
atmel,rtt-rtc-time-reg is a mandatory property and encodes the GPBR
register used to store the time base when the RTT is used as an RTC.
Align the RTT with what's currently done for sam9x60ek and sama7g5ek,
and enable it by default even if RTC is also enabled.
Signed-off-by: Tudor Ambarus <tudor.ambarus@linaro.org>
[nicolas.ferre@microchip.com: adapt to newer kernel] Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com> Link: https://lore.kernel.org/r/20230928143644.208515-1-nicolas.ferre@microchip.com Signed-off-by: Claudiu Beznea <claudiu.beznea@tuxon.dev>
Andreas Kemnade [Sun, 24 Sep 2023 22:27:18 +0000 (00:27 +0200)]
ARM: dts: omap: omap4-embt2ws: Let IMU driver handle Magnetometer internally
Possibility to use the i2c gate is only for compatibility reasons,
so avoid messing around with additional i2c busses.
Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
Message-ID: <20230924222718.2038849-1-andreas@kemnade.info> Signed-off-by: Tony Lindgren <tony@atomide.com>
Add the default MODE setting of a GPIO pin that was missing from the device
tree (i.e. P2.20/gpio2_00). This is to ensure the GPIO pins match the
pocketbeagle wiring expectations.
Signed-off-by: Trevor Woerner <twoerner@gmail.com>
Message-ID: <20230822143051.7640-5-twoerner@gmail.com>
[tony@atomide.com: leave out extra line break] Signed-off-by: Tony Lindgren <tony@atomide.com>
Trevor Woerner [Tue, 22 Aug 2023 14:30:49 +0000 (10:30 -0400)]
ARM: dts: am335x-pocketbeagle: enable pru
Now that the PRU code is upstream and can be loaded via remoteproc, adjust
the device tree to enable it and adjust the pin muxing so that the default
setting of the pins matches what's is given on the silkscreen and/or
pocketbeagle wiring.
Caveat:
In most cases, the silkscreen will indicate, for example, "PRU0.7",
but it doesn't indicate whether that pin should be enabled for input
or output. On the PRU a different MODE is used for input versus
output. So it is unclear which mode to enable (MODE5 = output, MODE6
= input). In cases where there is a choice (PRU1.11, PRU0.7, PRU0.4,
PRU0.1, PRU1.10, PRU0.6, PRU0.3, PRU0.2, and PRU0.5) output is assumed
(MODE5).
The remaining PRU silkscreen pins do not have a choice and are set as
follows:
PRU0.16 MODE5 input
PRU0.15i MODE6 input
Signed-off-by: Trevor Woerner <twoerner@gmail.com>
Message-ID: <20230822143051.7640-4-twoerner@gmail.com>
[tony@atomide.com: formatted description to fit 75 characters] Signed-off-by: Tony Lindgren <tony@atomide.com>
Remove the self-referenceing "pinctrl-0" entry inside the pinmux clause.
This eliminates the set of boot messages (one for each referenced pin)
similar to the following:
platform 44e10800.pinmux: Fixed dependency cycle(s) with /ocp/interconnect@44c00000/segment@200000/target-module@10000/scm@0/pinmux@800/pinmux_P2_17_gpio
Signed-off-by: Trevor Woerner <twoerner@gmail.com>
Message-ID: <20230822143051.7640-3-twoerner@gmail.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
Andreas Kemnade [Sat, 19 Aug 2023 14:31:09 +0000 (16:31 +0200)]
ARM: dts: omap4: embt2ws: add LED
Add LED since the driver is now available.
Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
Message-ID: <20230819143109.471615-1-andreas@kemnade.info> Signed-off-by: Tony Lindgren <tony@atomide.com>
On UCLB/KF, we intuitively think we want to handle these as "2 Sound
Cards":
card0,0: 1st sound of ULCB (SSI0 - ak4613)
card0,1: 2nd sound of ULCB (SSI2 - HDMI)
card1,0: 1st sound of KF (SSI3 - pcm3168a)
^ ^
However, because of ASoC Component vs. Card framework limitations, we
needed to handle this as "1 big Sound Card":
card0,0: 1st sound of ULCB/KF (SSI0 - ak4613)
card0,1: 2nd sound of ULCB/KF (SSI2 - HDMI)
card0,2: 3rd sound of ULCB/KF (SSI3 - pcm3168a)
^ ^
Now ASoC supports multi Component, which allows us to handle "2 Sound
Cards" such as "ULCB Sound Card" and "Kingfisher Sound Card", all
ULCB/KF Audio dtsi can be updated.
Note that this changes the Sound Card specification method from
userland, especially for Kingfisher Sound.
Add device nodes for the dual Spansion S25FL512S QSPI NOR FLASH and the
Spansion S29GL512S CFI NOR FLASH on the RSK+RZA1 development board.
The former is mapped directly through the SPI Multi I/O Bus Controller.
The latter resides in the external address space of the Bus State
Controller (BSC).
Add device nodes for the dual Spansion S25FL512S QSPI NOR FLASH and the
two Spansion S29GL512S CFI NOR FLASHes on the Genmai development board.
The former is mapped directly through the SPI Multi I/O Bus Controller.
The latter reside in the address space of the Bus State Controller
(BSC).
ARM: dts: renesas: wheat: Move Ethernet node to LBSC
The SMSC LAN89218AQ Ethernet controller on the Wheat development board
resides in the external address space of the Local Bus State Controller
(LBSC). Move the Ethernet device node to reflect this.
ARM: dts: renesas: blanche: Move Ethernet node to LBSC
The SMSC LAN89218AQ Ethernet controller on the Blanche development board
resides in the external address space of the Local Bus State Controller
(LBSC). Move the Ethernet device node to reflect this.
ARM: dts: renesas: marzen: Move Ethernet node to LBSC
The SMSC LAN89218AQ Ethernet controller on the Marzen development board
resides in the external address space of the Local Bus State Controller
(LBSC). Move the Ethernet device node to reflect this.
Add a minimal device node for the Local Bus State Controller (LBSC) on
the R-Car V2H SoC, to be extended by board DTS files for devices
residing in the LBSC external address space.
Add a minimal device node for the Local Bus State Controller (LBSC) on
the R-Car H1 SoC, to be extended by board DTS files for devices residing
in the LBSC external address space.
Add a minimal device node for the Bus State Controller (BSC) on the
RZ/A1H SoC, to be extended by board DTS files for devices residing in
the BSC external address space.
ARM: dts: renesas: Remove unused LBSC nodes from board DTS
Several board DTS files contain minimal device nodes that represent
on-SoC Local Bus State Controllers (LBSC), although they belong in the
SoC-specific DTS files instead. As these device nodes are incomplete
and unused, and hamper adding proper nodes later, it is better to just
remove them.
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull kvm fixes from Paolo Bonzini:
"ARM:
- Fix EL2 Stage-1 MMIO mappings where a random address was used
- Fix SMCCC function number comparison when the SVE hint is set
RISC-V:
- Fix KVM_GET_REG_LIST API for ISA_EXT registers
- Fix reading ISA_EXT register of a missing extension
- Fix ISA_EXT register handling in get-reg-list test
- Fix filtering of AIA registers in get-reg-list test
x86:
- Fixes for TSC_AUX virtualization
- Stop zapping page tables asynchronously, since we don't zap them as
often as before"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: SVM: Do not use user return MSR support for virtualized TSC_AUX
KVM: SVM: Fix TSC_AUX virtualization setup
KVM: SVM: INTERCEPT_RDTSCP is never intercepted anyway
KVM: x86/mmu: Stop zapping invalidated TDP MMU roots asynchronously
KVM: x86/mmu: Do not filter address spaces in for_each_tdp_mmu_root_yield_safe()
KVM: x86/mmu: Open code leaf invalidation from mmu_notifier
KVM: riscv: selftests: Selectively filter-out AIA registers
KVM: riscv: selftests: Fix ISA_EXT register handling in get-reg-list
RISC-V: KVM: Fix riscv_vcpu_get_isa_ext_single() for missing extensions
RISC-V: KVM: Fix KVM_GET_REG_LIST API for ISA_EXT registers
KVM: selftests: Assert that vasprintf() is successful
KVM: arm64: nvhe: Ignore SVE hint in SMCCC function ID
KVM: arm64: Properly return allocated EL2 VA from hyp_alloc_private_va_range()
Merge tag 'trace-v6.6-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/trace/linux-trace
Pull tracing fixes from Steven Rostedt:
- Fix the "bytes" output of the per_cpu stat file
The tracefs/per_cpu/cpu*/stats "bytes" was giving bogus values as the
accounting was not accurate. It is suppose to show how many used
bytes are still in the ring buffer, but even when the ring buffer was
empty it would still show there were bytes used.
- Fix a bug in eventfs where reading a dynamic event directory (open)
and then creating a dynamic event that goes into that diretory screws
up the accounting.
On close, the newly created event dentry will get a "dput" without
ever having a "dget" done for it. The fix is to allocate an array on
dir open to save what dentries were actually "dget" on, and what ones
to "dput" on close.
* tag 'trace-v6.6-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/trace/linux-trace:
eventfs: Remember what dentries were created on dir open
ring-buffer: Fix bytes info in per_cpu buffer stats
Merge tag 'cxl-fixes-6.6-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/cxl/cxl
Pull cxl fixes from Dan Williams:
"A collection of regression fixes, bug fixes, and some small cleanups
to the Compute Express Link code.
The regressions arrived in the v6.5 dev cycle and missed the v6.6
merge window due to my personal absences this cycle. The most
important fixes are for scenarios where the CXL subsystem fails to
parse valid region configurations established by platform firmware.
This is important because agreement between OS and BIOS on the CXL
configuration is fundamental to implementing "OS native" error
handling, i.e. address translation and component failure
identification.
Other important fixes are a driver load error when the BIOS lets the
Linux PCI core handle AER events, but not CXL memory errors.
The other fixex might have end user impact, but for now are only known
to trigger in our test/emulation environment.
Summary:
- Fix multiple scenarios where platform firmware defined regions fail
to be assembled by the CXL core.
- Fix a spurious driver-load failure on platforms that enable OS
native AER, but not OS native CXL error handling.
- Fix a regression detecting "poison" commands when "security"
commands are also defined.
- Fix a cxl_test regression with the move to centralize CXL port
register enumeration in the CXL core.
- Miscellaneous small fixes and cleanups"
* tag 'cxl-fixes-6.6-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/cxl/cxl:
cxl/acpi: Annotate struct cxl_cxims_data with __counted_by
cxl/port: Fix cxl_test register enumeration regression
cxl/region: Refactor granularity select in cxl_port_setup_targets()
cxl/region: Match auto-discovered region decoders by HPA range
cxl/mbox: Fix CEL logic for poison and security commands
cxl/pci: Replace host_bridge->native_aer with pcie_aer_is_native()
PCI/AER: Export pcie_aer_is_native()
cxl/pci: Fix appropriate checking for _OSC while handling CXL RAS registers
projects / linux.git / log