Make sure that the __le32 fields of struct ssp_ini_io_start_req are
manipulated after applying the correct endian conversion. That is, use
cpu_to_le32() for assigning values and le32_to_cpu() for consulting a field
value. In particular, make sure that the calculations for the 4G boundary
check are done using CPU endianness and *not* little endian values. With
these fixes, many sparse warnings are removed.
While at it, add blank lines after variable declarations and in some other
places to make this code more readable.
Link: https://lore.kernel.org/r/20220220031810.738362-11-damien.lemoal@opensource.wdc.com Fixes: 0ecdf00ba6e5 ("[SCSI] pm80xx: 4G boundary fix.") Reviewed-by: Jack Wang <jinpu.wang@ionos.com> Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
All fields of the kek_mgmt_req structure have the type __le32. So make sure
to use cpu_to_le32() to initialize them. This suppresses the sparse
warning:
warning: incorrect type in assignment (different base types)
expected restricted __le32 [addressable] [assigned] [usertype] new_curidx_ksop
got int
Link: https://lore.kernel.org/r/20220220031810.738362-10-damien.lemoal@opensource.wdc.com Fixes: f5860992db55 ("[SCSI] pm80xx: Added SPCv/ve specific hardware functionalities and relevant changes in common files") Reviewed-by: Jack Wang <jinpu.wang@ionos.com> Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
All fields of the SASProtocolTimerConfig structure have the __le32 type.
As such, use cpu_to_le32() to initialize them. This change suppresses many
sparse warnings:
warning: incorrect type in assignment (different base types)
expected restricted __le32 [addressable] [usertype] pageCode
got int
Note that the check to limit the value of the STP_IDLE_TMO field is removed
as this field is initialized using the fixed (and small) value defined by
the STP_IDLE_TIME macro.
The pm8001_dbg() calls printing the values of the SASProtocolTimerConfig
structure fileds are changed to use le32_to_cpu() to present the values in
human readable form.
Link: https://lore.kernel.org/r/20220220031810.738362-9-damien.lemoal@opensource.wdc.com Fixes: a6cb3d012b98 ("[SCSI] pm80xx: thermal, sas controller config and error handling update") Reviewed-by: Jack Wang <jinpu.wang@ionos.com> Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The fields of the set_ctrl_cfg_req structure have the __le32 type, so use
cpu_to_le32() to assign them. This removes the sparse warnings:
warning: incorrect type in assignment (different base types)
expected restricted __le32
got unsigned int
Link: https://lore.kernel.org/r/20220220031810.738362-8-damien.lemoal@opensource.wdc.com Fixes: 842784e0d15b ("pm80xx: Update For Thermal Page Code") Fixes: f5860992db55 ("[SCSI] pm80xx: Added SPCv/ve specific hardware functionalities and relevant changes in common files") Reviewed-by: John Garry <john.garry@huawei.com> Reviewed-by: Jack Wang <jinpu.wang@ionos.com> Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The ds_ads_m field of struct ssp_ini_tm_start_req has the type __le32.
Assigning a value to it should thus use cpu_to_le32(). This fixes the
sparse warning:
warning: incorrect type in assignment (different base types)
expected restricted __le32 [addressable] [assigned] [usertype] ds_ads_m
got int
Link: https://lore.kernel.org/r/20220220031810.738362-7-damien.lemoal@opensource.wdc.com Fixes: dbf9bfe61571 ("[SCSI] pm8001: add SAS/SATA HBA driver") Reviewed-by: Jack Wang <jinpu.wang@ionos.com> Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Since the sata_cmd struct is zeroed out before its fields are initialized,
there is no need for using "|=" to initialize the ncqtag_atap_dir_m
field. Using a standard assignment removes the sparse warning:
warning: invalid assignment: |=
Also, since the ncqtag_atap_dir_m field has type __le32, use cpu_to_le32()
to generate the assigned value.
Link: https://lore.kernel.org/r/20220220031810.738362-5-damien.lemoal@opensource.wdc.com Fixes: c6b9ef5779c3 ("[SCSI] pm80xx: NCQ error handling changes") Reviewed-by: John Garry <john.garry@huawei.com> Reviewed-by: Jack Wang <jinpu.wang@ionos.com> Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
If 'vfio_pci_core_device::needs_pm_restore' is set (PCI device does
not have No_Soft_Reset bit set in its PMCSR config register), then the
current PCI state will be saved locally in
'vfio_pci_core_device::pm_save' during D0->D3hot transition and same
will be restored back during D3hot->D0 transition. For reset-related
functionalities, vfio driver uses PCI reset API's. These
API's internally change the PCI power state back to D0 first if
the device power state is non-D0. This state change to D0 will happen
without the involvement of vfio driver.
Let's consider the following example:
1. The device is in D3hot.
2. User invokes VFIO_DEVICE_RESET ioctl.
3. pci_try_reset_function() will be called which internally
invokes pci_dev_save_and_disable().
4. pci_set_power_state(dev, PCI_D0) will be called first.
5. pci_save_state() will happen then.
Now, for the devices which has NoSoftRst-, the pci_set_power_state()
can trigger soft reset and the original PCI config state will be lost
at step (4) and this state cannot be restored again. This original PCI
state can include any setting which is performed by SBIOS or host
linux kernel (for example LTR, ASPM L1 substates, etc.). When this
soft reset will be triggered, then all these settings will be reset,
and the device state saved at step (5) will also have this setting
cleared so it cannot be restored. Since the vfio driver only exposes
limited PCI capabilities to its user, so the vfio driver user also
won't have the option to save and restore these capabilities state
either and these original settings will be permanently lost.
For pci_reset_bus() also, we can have the above situation.
The other functions/devices can be in D3hot and the reset will change
the power state of all devices to D0 without the involvement of vfio
driver.
So, before calling any reset-related API's, we need to make sure that
the device state is D0. This is mainly to preserve the state around
soft reset.
For vfio_pci_core_disable(), we use __pci_reset_function_locked()
which internally can use pci_pm_reset() for the function reset.
pci_pm_reset() requires the device power state to be in D0, otherwise
it returns error.
This patch changes the device power state to D0 by invoking
vfio_pci_set_power_state() explicitly before calling any reset related
API's.
Fixes: 51ef3a004b1e ("vfio/pci: Restore device state on PM transition") Signed-off-by: Abhishek Sahu <abhsahu@nvidia.com> Link: https://lore.kernel.org/r/20220217122107.22434-3-abhsahu@nvidia.com Signed-off-by: Alex Williamson <alex.williamson@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
If 'vfio_pci_core_device::needs_pm_restore' is set (PCI device does
not have No_Soft_Reset bit set in its PMCSR config register), then
the current PCI state will be saved locally in
'vfio_pci_core_device::pm_save' during D0->D3hot transition and same
will be restored back during D3hot->D0 transition.
For saving the PCI state locally, pci_store_saved_state() is being
used and the pci_load_and_free_saved_state() will free the allocated
memory.
But for reset related IOCTLs, vfio driver calls PCI reset-related
API's which will internally change the PCI power state back to D0. So,
when the guest resumes, then it will get the current state as D0 and it
will skip the call to vfio_pci_set_power_state() for changing the
power state to D0 explicitly. In this case, the memory pointed by
'pm_save' will never be freed. In a malicious sequence, the state changing
to D3hot followed by VFIO_DEVICE_RESET/VFIO_DEVICE_PCI_HOT_RESET can be
run in a loop and it can cause an OOM situation.
This patch frees the earlier allocated memory first before overwriting
'pm_save' to prevent the mentioned memory leak.
Fixes: 51ef3a004b1e ("vfio/pci: Restore device state on PM transition") Signed-off-by: Abhishek Sahu <abhsahu@nvidia.com> Link: https://lore.kernel.org/r/20220217122107.22434-2-abhsahu@nvidia.com Signed-off-by: Alex Williamson <alex.williamson@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Explicitly convert unsigned int in the right of the conditional
expression to int to match the left side operand and the return type,
fixing the following compiler warning:
drivers/md/dm-crypt.c:2593:43: warning: signed and unsigned
type in conditional expression [-Wsign-compare]
Fixes: c538f6ec9f56 ("dm crypt: add ability to use keys from the kernel key retention service") Signed-off-by: Aashish Sharma <shraash@google.com> Signed-off-by: Mike Snitzer <snitzer@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
DP audio enablement code which is comparing intf_type,
DRM_MODE_ENCODER_TMDS (= 2) with DRM_MODE_CONNECTOR_DisplayPort (= 10).
Which would never succeed. Fix it to check for DRM_MODE_ENCODER_TMDS.
Fixes: d13e36d7d222 ("drm/msm/dp: add audio support for Display Port on MSM") Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com> Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org> Reviewed-by: Stephen Boyd <swboyd@chromium.org> Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> Link: https://lore.kernel.org/r/20220217035358.465904-2-dmitry.baryshkov@linaro.org Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The dsi_7nm_phy_enable() disagrees with downstream for
glbl_str_swi_cal_sel_ctrl and glbl_hstx_str_ctrl_0 values. Update
programmed settings to match downstream driver. To remove the
possibility for such errors in future drop less_than_1500_mhz
assignment and specify settings explicitly.
All DSI PHY/PLL drivers were referencing their VCO parent clock by a
global name, most of which don't exist or have been renamed. These
clock drivers seem to function fine without that except the 14nm driver
for sdm6xx [1].
At the same time all DTs provide a "ref" clock as per the requirements
of dsi-phy-common.yaml, but the clock is never used. This patchset puts
that clock to use without relying on a global clock name, so that all
dependencies are explicitly defined in DT (the firmware) in the end.
Note that this patch intentionally breaks older firmware (DT) that
relies on the clock to be found globally instead. The only affected
platform is msm8974 [2] for whose dsi_phy_28nm a .name="xo" fallback is
left in place to accommodate a more graceful transition period. All
other platforms had the "ref" clock added to their phy node since its
inception, or in a followup patch some time after. These patches
wrongly assumed that the "ref" clock was actively used and have hence
been listed as "Fixes:" below.
Furthermore apq8064 was providing the wrong 19.2MHz cxo instead of
27MHz pxo clock, which has been addressed in [3].
It is expected that both [2] and [3] are applied to the tree well in
advance of this patch such that any actual breakage is extremely
unlikely, but might still occur if kernel upgrades are performed without
the DT to match. After some time the fallback for msm8974 can be
removed again as well.
Fixes: 79e51645a1dd ("arm64: dts: qcom: msm8916: Set 'xo_board' as ref clock of the DSI PHY") Fixes: 6969d1d9c615 ("ARM: dts: qcom-apq8064: Set 'cxo_board' as ref clock of the DSI PHY") Fixes: 0c0e72705a33 ("arm64: dts: sdm845: Set 'bi_tcxo' as ref clock of the DSI PHYs") Signed-off-by: Marijn Suijten <marijn.suijten@somainline.org> Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@somainline.org> Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> Link: https://lore.kernel.org/r/20210911131922.387964-2-marijn.suijten@somainline.org Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Some of DP link compliant test expects to return fail-safe mode
if prefer detailed timing mode can not be supported by mainlink's
lane and rate after link training. Therefore add fail-safe mode
into connector mode list as backup mode. This patch fixes test
case 4.2.2.1.
Changes in v2:
-- add Fixes text string
Fixes: 4b85d405cfe9 ( "drm/msm/dp: reduce link rate if failed at link training 1") Signed-off-by: Kuogee Hsieh <quic_khsieh@quicinc.com> Reviewed-by: Stephen Boyd <swboyd@chromium.org> Link: https://lore.kernel.org/r/1643066274-25814-1-git-send-email-quic_khsieh@quicinc.com Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Each DP link training contains link training 1 followed by link
training 2. There is maximum of 5 retries of DP link training
before declared link training failed. It is required to stop link
training at end of link training 2 if it is failed so that next
link training 1 can start freshly. This patch fixes link compliance
test case 4.3.1.13 (Source Device Link Training EQ Fallback Test).
Changes in v10:
-- group into one series
Changes in v11:
-- drop drm/msm/dp: dp_link_parse_sink_count() return immediately if aux read
Fixes: 2e0adc765d88 ("drm/msm/dp: do not end dp link training until video is ready") Signed-off-by: Kuogee Hsieh <quic_khsieh@quicinc.com> Reviewed-by: Stephen Boyd <swboyd@chromium.org> Link: https://lore.kernel.org/r/1642531648-8448-5-git-send-email-quic_khsieh@quicinc.com Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
DP CTS test case 4.2.2.6 has valid edid with bad checksum on purpose
and expect DP source return correct checksum. During drm edid read,
correct edid checksum is calculated and stored at
connector::real_edid_checksum.
The problem is struct dp_panel::connector never be assigned, instead the
connector is stored in struct msm_dp::connector. When we run compliance
testing test case 4.2.2.6 dp_panel_handle_sink_request() won't have a valid
edid set in struct dp_panel::edid so we'll try to use the connectors
real_edid_checksum and hit a NULL pointer dereference error because the
connector pointer is never assigned.
Changes in V2:
-- populate panel connector at msm_dp_modeset_init() instead of at dp_panel_read_sink_caps()
Changes in V3:
-- remove unhelpful kernel crash trace commit text
-- remove renaming dp_display parameter to dp
Changes in V4:
-- add more details to commit text
Changes in v10:
-- group into one series
Changes in v11:
-- drop drm/msm/dp: dp_link_parse_sink_count() return immediately if aux read
In devicetree the flash information is embedded within nand chip node,
so during nand chip initialization the nand chip node should be passed
to nand_set_flash_node() api, instead of nand controller node.
Fixes: 08d8c62164a3 ("mtd: rawnand: pl353: Add support for the ARM PL353 SMC NAND controller") Signed-off-by: Amit Kumar Mahapatra <amit.kumar-mahapatra@xilinx.com> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com> Link: https://lore.kernel.org/linux-mtd/20220209053427.27676-1-amit.kumar-mahapatra@xilinx.com Signed-off-by: Sasha Levin <sashal@kernel.org>
Currently the error -EIO is being assinged to variable ret when
the READY_BIT is not set but the function iwlagn_mac_start returns
0 rather than ret. Fix this by returning ret instead of 0.
Addresses-Coverity: ("Unused value") Fixes: 7335613ae27a ("iwlwifi: move all mac80211 related functions to one place") Signed-off-by: Colin Ian King <colin.king@canonical.com> Link: https://lore.kernel.org/r/20210907104658.14706-1-colin.king@canonical.com Signed-off-by: Luca Coelho <luciano.coelho@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Due to preg protection we cannot write to this register
while FW is running (when FW in Halt it is ok).
since we have some cases that we need to dump this
region while FW is running remove this writing from DRV.
FW will do this writing.
Since commit a05829a7222e ("cfg80211: avoid holding the RTNL when
calling the driver") we're not only holding the RTNL when going
in and out of suspend, but also the wiphy->mtx. Add that to the
D3 test debugfs in iwlwifi since it's required for various calls
to mac80211.
Fixes: a05829a7222e ("cfg80211: avoid holding the RTNL when calling the driver") Signed-off-by: Johannes Berg <johannes.berg@intel.com> Fixes: a05829a7222e ("cfg80211: avoid holding the RTNL when calling the driver") Signed-off-by: Luca Coelho <luciano.coelho@intel.com> Link: https://lore.kernel.org/r/iwlwifi.20220129105618.fcec0204e162.Ib73bf787ab4d83581de20eb89b1f8dbfcaaad0e3@changeid Signed-off-by: Luca Coelho <luciano.coelho@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
We may not have all the interfaces added to the driver when we get the
THERMAL_DUAL_CHAIN_REQUEST notification from the FW, so instead of
iterating all vifs to update SMPS, iterate only the ones that are
already assigned. The interfaces that were not assigned yet, will be
updated accordingly when we start using them.
The recent fix for NULL sta in iwl_mvm_get_tx_rate() still has a call
of iwl_mvm_sta_from_mac80211() that may be called with NULL sta.
Although this practically only points to the address and the actual
access doesn't happen due to the conditional evaluation at a later
point, it looks a bit flaky.
This patch drops the temporary variable above and evaluates
iwm_mvm_sta_from_mac80211() directly for avoiding confusions.
This patch added the data checksum error mib counters check for the
script mptcp_connect.sh when the data checksum is enabled.
In do_transfer(), got the mib counters twice, before and after running
the mptcp_connect commands. The latter minus the former is the actual
number of the data checksum mib counter.
The output looks like this:
ns1 MPTCP -> ns2 (dead:beef:1::2:10007) MPTCP (duration 86ms) [ OK ]
ns1 MPTCP -> ns2 (10.0.2.1:10008 ) MPTCP (duration 66ms) [ FAIL ]
server got 1 data checksum error[s]
Fixes: 94d66ba1d8e48 ("selftests: mptcp: enable checksum in mptcp_connect.sh") Closes: https://github.com/multipath-tcp/mptcp_net-next/issues/255 Signed-off-by: Geliang Tang <geliang.tang@suse.com> Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
This is caused by dax_fs_exit() not flushing inodes before destroy cache.
To fix this issue, call rcu_barrier() before destroy cache.
Signed-off-by: Tong Zhang <ztong0001@gmail.com> Reviewed-by: Ira Weiny <ira.weiny@intel.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Link: https://lore.kernel.org/r/20220212071111.148575-1-ztong0001@gmail.com Fixes: 7b6be8444e0f ("dax: refactor dax-fs into a generic provider of 'struct dax_device' instances") Signed-off-by: Dan Williams <dan.j.williams@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
[Why]
When display topology changed on DSC hub we add all crtcs with dsc support to
atomic state.
Refer to patch:"drm/amd/display: Trigger modesets on MST DSC connectors"
However the original implementation may skip crtc if the topology change
caused by unplug.
That potentially could lead to no-lightup or corruption on DSC hub after
unplug event on one of the connectors.
[How]
Update add_affected_mst_dsc_crtcs() to use old connector state
if new connector state has no crtc (undergoes modeset due to unplug)
Fixes: 44be939ff7ac58 ("drm/amd/display: Trigger modesets on MST DSC connectors") Reviewed-by: Hersen Wu <hersenwu@amd.com> Acked-by: Jasdeep Dhillon <jdhillon@amd.com> Signed-off-by: Roman Li <Roman.Li@amd.com> Tested-by: Daniel Wheeler <daniel.wheeler@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
[why]
pm sysfs should be writable in one VF mode as is in passthrough
[how]
do not remove write access on pm sysfs if device is in one VF mode
Fixes: 11c9cc95f818 ("amdgpu/pm: Make sysfs pm attributes as read-only for VFs") Signed-off-by: Yiqing Yao <yiqing.yao@amd.com> Reviewed-by: Monk Liu <Monk.liu@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
When reworking btf__get_from_id() in commit a19f93cfafdf the error
handling when calling bpf_btf_get_fd_by_id() changed. Before the rework
if bpf_btf_get_fd_by_id() failed the error would not be propagated to
callers of btf__get_from_id(), after the rework it is. This lead to a
change in behavior in print_key_value() that now prints an error when
trying to lookup keys in maps with no btf available.
Fix this by following the way used in dumping maps to allow to look up
keys in no-btf maps, by which it decides whether and where to get the
btf info according to the btf value type.
Fixes: a19f93cfafdf ("libbpf: Add internal helper to load BTF data by FD") Signed-off-by: Yinjun Zhang <yinjun.zhang@corigine.com> Signed-off-by: Simon Horman <simon.horman@corigine.com> Signed-off-by: Andrii Nakryiko <andrii@kernel.org> Reviewed-by: Niklas Söderlund <niklas.soderlund@corigine.com> Acked-by: Jiri Olsa <jolsa@kernel.org> Link: https://lore.kernel.org/bpf/1644249625-22479-1-git-send-email-yinjun.zhang@corigine.com Signed-off-by: Sasha Levin <sashal@kernel.org>
Because of the possible failure of the dma_supported(), the
dma_set_mask_and_coherent() may return error num.
Therefore, it should be better to check it and return the error if
fails.
Internally kernel prepends all report buffers, for both numbered and
unnumbered reports, with report ID, therefore to properly handle unnumbered
reports we should prepend it ourselves.
For the same reason we should skip the first byte of the buffer when
calling i2c_hid_set_or_send_report() which then will take care of properly
formatting the transfer buffer based on its separate report ID argument
along with report payload.
[jkosina@suse.cz: finalize trimmed sentence in changelog as spotted by Benjamin] Fixes: 9b5a9ae88573 ("HID: i2c-hid: implement ll_driver transport-layer callbacks") Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com> Tested-by: Benjamin Tissoires <benjamin.tissoires@redhat.com> Signed-off-by: Jiri Kosina <jkosina@suse.cz> Signed-off-by: Sasha Levin <sashal@kernel.org>
When receiving netlink messages, libbpf was using a statically allocated
stack buffer of 4k bytes. This happened to work fine on systems with a 4k
page size, but on systems with larger page sizes it can lead to truncated
messages. The user-visible impact of this was that libbpf would insist no
XDP program was attached to some interfaces because that bit of the netlink
message got chopped off.
Fix this by switching to a dynamically allocated buffer; we borrow the
approach from iproute2 of using recvmsg() with MSG_PEEK|MSG_TRUNC to get
the actual size of the pending message before receiving it, adjusting the
buffer as necessary. While we're at it, also add retries on interrupted
system calls around the recvmsg() call.
v2:
- Move peek logic to libbpf_netlink_recv(), don't double free on ENOMEM.
When the dw-hdmi bridge is in first place of the bridge chain, this
means there is no way to select an input format of the dw-hdmi HW
component.
Since introduction of display-connector, negotiation was broken since
the dw-hdmi negotiation code only worked when the dw-hdmi bridge was
in last position of the bridge chain or behind another bridge also
supporting input & output format negotiation.
Commit 7cd70656d128 ("drm/bridge: display-connector: implement bus fmts callbacks")
was introduced to make negotiation work again by making display-connector
act as a pass-through concerning input & output format negotiation.
But in the case where the dw-hdmi is single in the bridge chain, for
example on Renesas SoCs, with the display-connector bridge the dw-hdmi
is no more single, breaking output format.
Reported-by: Biju Das <biju.das.jz@bp.renesas.com> Bisected-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com> Tested-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com> Fixes: 6c3c719936da ("drm/bridge: synopsys: dw-hdmi: add bus format negociation") Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
[narmstrong: add proper fixes commit] Reviewed-by: Robert Foss <robert.foss@linaro.org> Link: https://patchwork.freedesktop.org/patch/msgid/20220204143337.89221-1-narmstrong@baylibre.com Signed-off-by: Sasha Levin <sashal@kernel.org>
In CXL 2.0, 8.2.5.1 CXL Capability Header Register: this register
is given as 32 bits.
8.2.3 which covers the CXL 2.0 Component registers, including the
CXL Capability Header Register states that access restrictions
specified in Section 8.2.2 apply.
8.2.2 includes:
* A 32 bit register shall be accessed as a 4 Byte quantity.
...
If these rules are not followed, the behavior is undefined.
Discovered during review of CXL QEMU emulation. Alex Bennée pointed
out there was a comment saying that 4 byte registers must be read
with a 4 byte read, but 8 byte reads were being emulated.
Fixing that, led to this code failing. Whilst a given hardware
implementation 'might' work with an 8 byte read, it should not be relied
upon. The QEMU emulation v5 will return 0 and log the wrong access width.
The code moved, so one fixes tag for where this will directly apply and
also a reference to the earlier introduction of the code for backports.
Fixes: 0f06157e0135 ("cxl/core: Move register mapping infrastructure") Fixes: 08422378c4ad ("cxl/pci: Add HDM decoder capabilities") Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Cc: Alex Bennée <alex.bennee@linaro.org> Reviewed-by: Ben Widawsky <ben.widawsky@intel.com> Link: https://lore.kernel.org/r/20220201153437.2873-1-Jonathan.Cameron@huawei.com Signed-off-by: Dan Williams <dan.j.williams@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
It's wrong to check the last packet by RXE_COMP_MASK because the flag is
to indicate if responder needs to generate a completion.
Fixes: 9fcd67d1772c ("IB/rxe: increment msn only when completing a request") Fixes: 8700e3e7c485 ("Soft RoCE driver") Link: https://lore.kernel.org/r/20211229034438.1854908-1-yangx.jy@fujitsu.com Signed-off-by: Xiao Yang <yangx.jy@fujitsu.com> Signed-off-by: Jason Gunthorpe <jgg@nvidia.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The emulated bridge returns incorrect value for PCI_EXP_RTSTA register
during readout in advk_pci_bridge_emul_pcie_conf_read() function: the
correct bit is BIT(16), but we are setting BIT(23), because the code
does
*value = (isr0 & PCIE_MSG_PM_PME_MASK) << 16
where
PCIE_MSG_PM_PME_MASK
is
BIT(7).
The code should probably have been something like
*value = (!!(isr0 & PCIE_MSG_PM_PME_MASK)) << 16,
but we are better of using an if() and using the proper macro for this
bit.
In advk_pcie_handle_msi() it is expected that when bit i in the W1C
register PCIE_MSI_STATUS_REG is cleared, the PCIE_MSI_PAYLOAD_REG is
updated to contain the MSI number corresponding to index i.
Experiments show that this is not so, and instead PCIE_MSI_PAYLOAD_REG
always contains the number of the last received MSI, overall.
Do not read PCIE_MSI_PAYLOAD_REG register for determining MSI interrupt
number. Since Aardvark already forbids more than 32 interrupts and uses
own allocated hwirq numbers, the msi_idx already corresponds to the
received MSI number.
On changing the RX ring parameters igb uses a hack to avoid a warning
when calling xdp_rxq_info_reg via igb_setup_rx_resources. It just
clears the struct xdp_rxq_info content.
Instead, change this to unregister if we're already registered. Align
code to the igc code.
igc_ethtool_set_ringparam() copies the igc_ring structure but neglects to
reset the xdp_rxq_info member before calling igc_setup_rx_resources().
This in turn calls xdp_rxq_info_reg() with an already registered xdp_rxq_info.
Make sure to unregister the xdp_rxq_info structure first in
igc_setup_rx_resources.
Fixes: 73f1071c1d29 ("igc: Add support for XDP_TX action") Reported-by: Lennert Buytenhek <buytenh@arista.com> Signed-off-by: Corinna Vinschen <vinschen@redhat.com> Acked-by: Vinicius Costa Gomes <vinicius.gomes@intel.com> Tested-by: Dvora Fuxbrumer <dvorax.fuxbrumer@linux.intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Currently autoloading for SPI devices does not use the DT ID table, it uses
SPI modalises. Supporting OF modalises is going to be difficult if not
impractical, an attempt was made but has been reverted, so ensure that
module autoloading works for this driver by adding an id_table listing the
SPI IDs for everything.
Fixes: 96c8395e2166 ("spi: Revert modalias changes") Signed-off-by: Mark Brown <broonie@kernel.org> Reviewed-by: Michael Walle <michael@walle.cc> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com> Link: https://lore.kernel.org/linux-mtd/20220202143404.16070-4-broonie@kernel.org Signed-off-by: Sasha Levin <sashal@kernel.org>
Currently autoloading for SPI devices does not use the DT ID table, it uses
SPI modalises. Supporting OF modalises is going to be difficult if not
impractical, an attempt was made but has been reverted, so ensure that
module autoloading works for this driver by adding an id_table listing the
SPI IDs for everything.
Fixes: 96c8395e2166 ("spi: Revert modalias changes") Signed-off-by: Mark Brown <broonie@kernel.org> Reviewed-by: Michael Walle <michael@walle.cc> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com> Link: https://lore.kernel.org/linux-mtd/20220202143404.16070-3-broonie@kernel.org Signed-off-by: Sasha Levin <sashal@kernel.org>
Some resource should be released if an error occurs in
'bcm2835_i2c_probe()'.
Add an error handling path and the needed 'clk_disable_unprepare()' and
'clk_rate_exclusive_put()' calls.
While at it, rework the bottom of the function to use this newly added
error handling path and have an explicit and more standard "return 0;" at
the end of the normal path.
Fixes: bebff81fb8b9 ("i2c: bcm2835: Model Divider in CCF") Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
[wsa: rebased] Signed-off-by: Wolfram Sang <wsa@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
platform_get_resource(pdev, IORESOURCE_IRQ, ..) relies on static
allocation of IRQ resources in DT core code, this causes an issue
when using hierarchical interrupt domains using "interrupts" property
in the node as this bypasses the hierarchical setup and messes up the
irq chaining.
In preparation for removal of static setup of IRQ resource from DT core
code use platform_get_irq().
Syzbot once again hit uninit value in asix driver. The problem still the
same -- asix_read_cmd() reads less bytes, than was requested by caller.
Since all read requests are performed via asix_read_cmd() let's catch
usb related error there and add __must_check notation to be sure all
callers actually check return value.
So, this patch adds sanity check inside asix_read_cmd(), that simply
checks if bytes read are not less, than was requested and adds missing
error handling of asix_read_cmd() all across the driver code.
Fixes: d9fe64e51114 ("net: asix: Add in_pm parameter") Reported-and-tested-by: syzbot+6ca9f7867b77c2d316ac@syzkaller.appspotmail.com Signed-off-by: Pavel Skripkin <paskripkin@gmail.com> Tested-by: Oleksij Rempel <o.rempel@pengutronix.de> Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Running with POSIXLY_CORRECT=1 in the environment the scripts/dtc build
fails, because pkg-config doesn't output anything when the flags come
after the arguments.
Fixes: 067c650c456e ("dtc: Use pkg-config to locate libyaml") Signed-off-by: Thomas Bracht Laumann Jespersen <t@laumann.xyz> Signed-off-by: Rob Herring <robh@kernel.org> Link: https://lore.kernel.org/r/20220131112028.7907-1-t@laumann.xyz Signed-off-by: Sasha Levin <sashal@kernel.org>
If we're limiting bandwidth for some reason such as regulatory
restrictions, then advertise that limitation just like we do
for VHT today, so the AP is aware we cannot use the higher BW
it might be using.
Fixes: 73f37068d540 ("ptp: support ptp physical/virtual clocks conversion") Signed-off-by: Miroslav Lichvar <mlichvar@redhat.com> Acked-by: Richard Cochran <richardcochran@gmail.com> Cc: Yangbo Lu <yangbo.lu@nxp.com> Cc: Yang Yingliang <yangyingliang@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
mac80211 provides aid in vif->bss_conf.aid for sta mode and not in
sta->aid. Fix mt7915_mcu_wtbl_generic_tlv routine using proper value for
aid in sta mode.
Fixes: e57b7901469fc ("mt76: add mac80211 driver for MT7915 PCIe-based chipsets") Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org> Signed-off-by: Felix Fietkau <nbd@nbd.name> Signed-off-by: Sasha Levin <sashal@kernel.org>
Trace IMC (In-Memory collection counters) in powerpc is useful for
application level profiling.
For trace_imc, presently task context (task_ctx_nr) is set to
perf_hw_context. But perf_hw_context should only be used for CPU PMU.
See commit 26657848502b ("perf/core: Verify we have a single
perf_hw_context PMU").
So for trace_imc, even though it is per thread PMU, it is preferred to
use sw_context in order to be able to do application level monitoring.
Hence change the task_ctx_nr to use perf_sw_context.
On board rev A, the network interface labels for the switch ports
written on the front panel are different than on rev B and later.
This patch fixes network interface names for the switch ports according
to labels that are written on the front panel of the board rev B.
They start from ETH3 and end at ETH10.
This patch also introduces a separate device tree for rev A.
The main device tree is supposed to cover rev B and later.
As the possible failure of the ioremap(), the 'local->sram' and other
two could be NULL.
Therefore it should be better to check it in order to avoid the later
dev_dbg.
For now, if the XDP prog returns XDP_PASS on XSK, the metadata
will be lost as it doesn't get copied to the skb.
Copy it along with the frame headers. Account its size on skb
allocation, and when copying just treat it as a part of the frame
and do a pull after to "move" it to the "reserved" zone.
net_prefetch() xdp->data_meta and align the copy size to speed-up
memcpy() a little and better match ixgbe_construct_skb().
Fixes: d0bcacd0a130 ("ixgbe: add AF_XDP zero-copy Rx support") Suggested-by: Jesper Dangaard Brouer <brouer@redhat.com> Suggested-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com> Signed-off-by: Alexander Lobakin <alexandr.lobakin@intel.com> Reviewed-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com> Tested-by: Sandeep Penigalapati <sandeep.penigalapati@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
{__,}napi_alloc_skb() allocates and reserves additional NET_SKB_PAD
+ NET_IP_ALIGN for any skb.
OTOH, ixgbe_construct_skb_zc() currently allocates and reserves
additional `xdp->data - xdp->data_hard_start`, which is
XDP_PACKET_HEADROOM for XSK frames.
There's no need for that at all as the frame is post-XDP and will
go only to the networking stack core.
Pass the size of the actual data only to __napi_alloc_skb() and
don't reserve anything. This will give enough headroom for stack
processing.
Fixes: d0bcacd0a130 ("ixgbe: add AF_XDP zero-copy Rx support") Signed-off-by: Alexander Lobakin <alexandr.lobakin@intel.com> Reviewed-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com> Tested-by: Sandeep Penigalapati <sandeep.penigalapati@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
To not dereference bi->xdp each time in ixgbe_construct_skb_zc(),
pass bi->xdp as an argument instead of bi. We can also call
xsk_buff_free() outside of the function as well as assign bi->xdp
to NULL, which seems to make it closer to its name.
Suggested-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com> Signed-off-by: Alexander Lobakin <alexandr.lobakin@intel.com> Tested-by: Sandeep Penigalapati <sandeep.penigalapati@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
{__,}napi_alloc_skb() allocates and reserves additional NET_SKB_PAD
+ NET_IP_ALIGN for any skb.
OTOH, igc_construct_skb_zc() currently allocates and reserves
additional `xdp->data_meta - xdp->data_hard_start`, which is about
XDP_PACKET_HEADROOM for XSK frames.
There's no need for that at all as the frame is post-XDP and will
go only to the networking stack core.
Pass the size of the actual data only (+ meta) to
__napi_alloc_skb() and don't reserve anything. This will give
enough headroom for stack processing.
Also, net_prefetch() xdp->data_meta and align the copy size to
speed-up memcpy() a little and better match igc_construct_skb().
Fixes: fc9df2a0b520 ("igc: Enable RX via AF_XDP zero-copy") Signed-off-by: Alexander Lobakin <alexandr.lobakin@intel.com> Reviewed-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com> Tested-by: Nechama Kraus <nechamax.kraus@linux.intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
For now, if the XDP prog returns XDP_PASS on XSK, the metadata will
be lost as it doesn't get copied to the skb.
Copy it along with the frame headers. Account its size on skb
allocation, and when copying just treat it as a part of the frame
and do a pull after to "move" it to the "reserved" zone.
net_prefetch() xdp->data_meta and align the copy size to speed-up
memcpy() a little and better match i40e_construct_skb().
Fixes: 0a714186d3c0 ("i40e: add AF_XDP zero-copy Rx support") Suggested-by: Jesper Dangaard Brouer <brouer@redhat.com> Suggested-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com> Signed-off-by: Alexander Lobakin <alexandr.lobakin@intel.com> Reviewed-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com> Tested-by: Kiran Bhandare <kiranx.bhandare@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
{__,}napi_alloc_skb() allocates and reserves additional NET_SKB_PAD
+ NET_IP_ALIGN for any skb.
OTOH, i40e_construct_skb_zc() currently allocates and reserves
additional `xdp->data - xdp->data_hard_start`, which is
XDP_PACKET_HEADROOM for XSK frames.
There's no need for that at all as the frame is post-XDP and will
go only to the networking stack core.
Pass the size of the actual data only to __napi_alloc_skb() and
don't reserve anything. This will give enough headroom for stack
processing.
timestamping checks socket options during initialisation. For the field
bind_phc of the socket option SO_TIMESTAMPING it expects the value -1 if
PHC is not bound. Actually the value of bind_phc is 0 if PHC is not
bound. This results in the following output:
This is fixed by setting default value and expected value of bind_phc to
0.
Fixes: 2214d7032479 ("selftests/net: timestamping: support binding PHC") Signed-off-by: Gerhard Engleder <gerhard@engleder-embedded.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
The MMIO emulation code for vector instructions is duplicated between
VSX and VMX. When emulating VMX we should check the VMX copy size
instead of the VSX one.
Syzbot reported 2 KMSAN bugs in ath9k. All of them are caused by missing
field initialization.
In htc_connect_service() svc_meta_len and pad are not initialized. Based
on code it looks like in current skb there is no service data, so simply
initialize svc_meta_len to 0.
htc_issue_send() does not initialize htc_frame_hdr::control array. Based
on firmware code, it will initialize it by itself, so simply zero whole
array to make KMSAN happy
Bytes 16-17 of 18 are uninitialized
Memory access of size 18 starts at ffff888027377e00
Fixes: fb9987d0f748 ("ath9k_htc: Support for AR9271 chipset.") Reported-by: syzbot+f83a1df1ed4f67e8d8ad@syzkaller.appspotmail.com Signed-off-by: Pavel Skripkin <paskripkin@gmail.com> Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com> Link: https://lore.kernel.org/r/20220115122733.11160-1-paskripkin@gmail.com Signed-off-by: Sasha Levin <sashal@kernel.org>
Use temp netns instead of hard code name for testing in case the netns
already exists.
Remove the hard code interface index when creating the veth interfaces.
Because when the system loads some virtual interface modules, e.g. tunnels.
the ifindex of 2 will be used and the cmd will fail.
As the netns has not created if checking environment failed. Trap the
clean up function after checking env.
Fixes: 8955c1a32987 ("selftests/bpf/xdp_redirect_multi: Limit the tests in netns") Signed-off-by: Hangbin Liu <liuhangbin@gmail.com> Acked-by: William Tu <u9012063@gmail.com> Link: https://lore.kernel.org/r/20220125081717.1260849-2-liuhangbin@gmail.com Signed-off-by: Alexei Starovoitov <ast@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Convert almost all SEC("xdp_blah") uses to strict SEC("xdp") to comply
with strict libbpf 1.0 logic of exact section name match for XDP program
types. There is only one exception, which is only tested through
iproute2 and defines multiple XDP programs within the same BPF object.
Given iproute2 still works in non-strict libbpf mode and it doesn't have
means to specify XDP programs by its name (not section name/title),
leave that single file alone for now until iproute2 gains lookup by
function/program name.
The fix to select the copper page on AR8031 was being done in the probe
function rather than config_init, so it would not be redone after resume
from suspend. Move this to config_init so it is always redone when
needed.
Fixes: c329e5afb42f ("net: phy: at803x: select correct page on config init") Signed-off-by: Robert Hancock <robert.hancock@calian.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
clang static analysis reports this represenative problem
amdgpu_smu.c:144:18: warning: The left operand of '*' is a garbage value
return clk_freq * 100;
~~~~~~~~ ^
If there is no get_dpm_ultimate_freq function,
smu_get_dpm_freq_range returns success without setting the
output min,max parameters. So return an -ENOTSUPP error.
Fixes: e5ef784b1e17 ("drm/amd/powerplay: revise calling chain on retrieving frequency range") Signed-off-by: Tom Rix <trix@redhat.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
In amdgpu_dm_connector_add_common_modes(), amdgpu_dm_create_common_mode()
is assigned to mode and is passed to drm_mode_probed_add() directly after
that. drm_mode_probed_add() passes &mode->head to list_add_tail(), and
there is a dereference of it in list_add_tail() without recoveries, which
could lead to NULL pointer dereference on failure of
amdgpu_dm_create_common_mode().
Fix this by adding a NULL check of mode.
This bug was found by a static analyzer.
Builds with 'make allyesconfig' show no new warnings,
and our static analyzer no longer warns about this code.
Fixes: e7b07ceef2a6 ("drm/amd/display: Merge amdgpu_dm_types and amdgpu_dm") Signed-off-by: Zhou Qingyang <zhou1615@umn.edu> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
In nvkm_acr_hsfw_load_bl(), the return value of kmalloc() is directly
passed to memcpy(), which could lead to undefined behavior on failure
of kmalloc().
Fix this bug by using kmemdup() instead of kmalloc()+memcpy().
This bug was found by a static analyzer.
Builds with 'make allyesconfig' show no new warnings,
and our static analyzer no longer warns about this code.
Fixes: 22dcda45a3d1 ("drm/nouveau/acr: implement new subdev to replace "secure boot"") Signed-off-by: Zhou Qingyang <zhou1615@umn.edu> Reviewed-by: Lyude Paul <lyude@redhat.com> Signed-off-by: Lyude Paul <lyude@redhat.com> Link: https://patchwork.freedesktop.org/patch/msgid/20220124165856.57022-1-zhou1615@umn.edu Signed-off-by: Sasha Levin <sashal@kernel.org>
It's possible the FW is already shutting down while the driver is being
removed and/or when the driver is going through reset. This can cause
unexpected/unnecessary errors to be printed:
The watchdog expects the lif to fully exist when it goes off,
so lets not start the watchdog until all is ready in case there
is some quirky time dialation that makes probe take multiple
seconds.
Fixes: 089406bc5ad6 ("ionic: add a watchdog timer to monitor heartbeat") Signed-off-by: Shannon Nelson <snelson@pensando.io> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Sparse seems to have gotten a little more picky lately and
we need to revisit this bit of code to make sparse happy.
warning: incorrect type in initializer (different address spaces)
expected union ionic_dev_cmd_regs *regs
got union ionic_dev_cmd_regs [noderef] __iomem *dev_cmd_regs
warning: incorrect type in argument 2 (different address spaces)
expected void [noderef] __iomem *
got unsigned int *
warning: incorrect type in argument 1 (different address spaces)
expected void volatile [noderef] __iomem *
got union ionic_dev_cmd *
Fixes: d701ec326a31 ("ionic: clean up sparse complaints") Signed-off-by: Shannon Nelson <snelson@pensando.io> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
The current code assumes that the RGB444 and YUV444 formats are the
same, but the HDMI 2.0 specification states that:
The three DC_XXbit bits above only indicate support for RGB 4:4:4 at
that pixel size. Support for YCBCR 4:4:4 in Deep Color modes is
indicated with the DC_Y444 bit. If DC_Y444 is set, then YCBCR 4:4:4
is supported for all modes indicated by the DC_XXbit flags.
So if we have YUV444 support and any DC_XXbit flag set but the DC_Y444
flag isn't, we'll assume that we support that deep colour mode for
YUV444 which breaks the specification.
In order to fix this, let's split the edid_hdmi_dc_modes field in struct
drm_display_info into two fields, one for RGB444 and one for YUV444.
Suggested-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Fixes: d0c94692e0a3 ("drm/edid: Parse and handle HDMI deep color modes.") Signed-off-by: Maxime Ripard <maxime@cerno.tech> Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20220120151625.594595-4-maxime@cerno.tech Signed-off-by: Sasha Levin <sashal@kernel.org>
The current code, when parsing the EDID Deep Color depths, that the
YUV422 cannot be used, referring to the HDMI 1.3 Specification.
This specification, in its section 6.2.4, indeed states:
For each supported Deep Color mode, RGB 4:4:4 shall be supported and
optionally YCBCR 4:4:4 may be supported.
YCBCR 4:2:2 is not permitted for any Deep Color mode.
This indeed can be interpreted like the code does, but the HDMI 1.4
specification further clarifies that statement in its section 6.2.4:
For each supported Deep Color mode, RGB 4:4:4 shall be supported and
optionally YCBCR 4:4:4 may be supported.
YCBCR 4:2:2 is also 36-bit mode but does not require the further use
of the Deep Color modes described in section 6.5.2 and 6.5.3.
This means that, even though YUV422 can be used with 12 bit per color,
it shouldn't be treated as a deep color mode.
This is also broken with YUV444 if it's supported by the display, but
DRM_EDID_HDMI_DC_Y444 isn't set. In such a case, the code will clear
color_formats of the YUV444 support set previously in
drm_parse_cea_ext(), but will not set it back.
Since the formats supported are already setup properly in
drm_parse_cea_ext(), let's just remove the code modifying the formats in
drm_parse_hdmi_deep_color_info()
Set the controller registers according to the real clock rate. The
controller registers configuration (setup, hold, timeout, ... cycles)
depends on the clock rate of the GPMI. Using the real rate instead of
the ideal one, avoids that this inaccuracy (required_rate - real_rate)
affects the registers setting.
This patch has been tested on two custom boards with i.MX28 and i.MX6
SOCs:
- i.MX28:
required rate 100MHz, real rate 99.3MHz
- i.MX6
required rate 100MHz, real rate 99MHz
Fixes: b1206122069a ("mtd: rawnand: gpmi: use core timings instead of an empirical derivation") Co-developed-by: Michael Trimarchi <michael@amarulasolutions.com> Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com> Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com> Tested-by: Sascha Hauer <s.hauer@pengutronix.de> Reviewed-by: Sascha Hauer <s.hauer@pengutronix.de> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com> Link: https://lore.kernel.org/linux-mtd/20220118095434.35081-3-dario.binacchi@amarulasolutions.com Signed-off-by: Sasha Levin <sashal@kernel.org>
For the possible failure of the platform_get_irq(), the returned irq
could be error number and will finally cause the failure of the
request_irq().
Consider that platform_get_irq() can now in certain cases return
-EPROBE_DEFER, and the consequences of letting request_irq() effectively
convert that into -EINVAL, even at probe time rather than later on.
So it might be better to check just now.
kvartet reported, that hci_uart_tx_wakeup() uses uninitialized rwsem.
The problem was in wrong place for percpu_init_rwsem() call.
hci_uart_proto::open() may register a timer whose callback may call
hci_uart_tx_wakeup(). There is a chance, that hci_uart_register_device()
thread won't be fast enough to call percpu_init_rwsem().
Fix it my moving percpu_init_rwsem() call before p->open().
INFO: trying to register non-static key.
The code is fine but needs lockdep annotation, or maybe
you didn't initialize this object before use?
turning off the locking correctness validator.
CPU: 2 PID: 18524 Comm: syz-executor.5 Not tainted 5.16.0-rc6 #9
...
Call Trace:
<IRQ>
__dump_stack lib/dump_stack.c:88 [inline]
dump_stack_lvl+0xcd/0x134 lib/dump_stack.c:106
assign_lock_key kernel/locking/lockdep.c:951 [inline]
register_lock_class+0x148d/0x1950 kernel/locking/lockdep.c:1263
__lock_acquire+0x106/0x57e0 kernel/locking/lockdep.c:4906
lock_acquire kernel/locking/lockdep.c:5637 [inline]
lock_acquire+0x1ab/0x520 kernel/locking/lockdep.c:5602
percpu_down_read_trylock include/linux/percpu-rwsem.h:92 [inline]
hci_uart_tx_wakeup+0x12e/0x490 drivers/bluetooth/hci_ldisc.c:124
h5_timed_event+0x32f/0x6a0 drivers/bluetooth/hci_h5.c:188
call_timer_fn+0x1a5/0x6b0 kernel/time/timer.c:1421
While working on code to populate kfunc BTF ID sets for module BTF from
its initcall, I noticed that by the time the initcall is invoked, the
module BTF can already be seen by userspace (and the BPF verifier). The
existing btf_try_get_module calls try_module_get which only fails if
mod->state == MODULE_STATE_GOING, i.e. it can increment module reference
when module initcall is happening in parallel.
Currently, BTF parsing happens from MODULE_STATE_COMING notifier
callback. At this point, the module initcalls have not been invoked.
The notifier callback parses and prepares the module BTF, allocates an
ID, which publishes it to userspace, and then adds it to the btf_modules
list allowing the kernel to invoke btf_try_get_module for the BTF.
However, at this point, the module has not been fully initialized (i.e.
its initcalls have not finished). The code in module.c can still fail
and free the module, without caring for other users. However, nothing
stops btf_try_get_module from succeeding between the state transition
from MODULE_STATE_COMING to MODULE_STATE_LIVE.
This leads to a use-after-free issue when BPF program loads
successfully in the state transition, load_module's do_init_module call
fails and frees the module, and BPF program fd on close calls module_put
for the freed module. Future patch has test case to verify we don't
regress in this area in future.
There are multiple points after prepare_coming_module (in load_module)
where failure can occur and module loading can return error. We
illustrate and test for the race using the last point where it can
practically occur (in module __init function).
An illustration of the race:
CPU 0 CPU 1
load_module
notifier_call(MODULE_STATE_COMING)
btf_parse_module
btf_alloc_id // Published to userspace
list_add(&btf_mod->list, btf_modules)
mod->init(...)
... ^
bpf_check |
check_pseudo_btf_id |
btf_try_get_module |
returns true | ...
... | module __init in progress
return prog_fd | ...
... V
if (ret < 0)
free_module(mod)
...
close(prog_fd)
...
bpf_prog_free_deferred
module_put(used_btf.mod) // use-after-free
We fix this issue by setting a flag BTF_MODULE_F_LIVE, from the notifier
callback when MODULE_STATE_LIVE state is reached for the module, so that
we return NULL from btf_try_get_module for modules that are not fully
formed. Since try_module_get already checks that module is not in
MODULE_STATE_GOING state, and that is the only transition a live module
can make before being removed from btf_modules list, this is enough to
close the race and prevent the bug.
A later selftest patch crafts the race condition artifically to verify
that it has been fixed, and that verifier fails to load program (with
ENXIO).
Lastly, a couple of comments:
1. Even if this race didn't exist, it seems more appropriate to only
access resources (ksyms and kfuncs) of a fully formed module which
has been initialized completely.
2. This patch was born out of need for synchronization against module
initcall for the next patch, so it is needed for correctness even
without the aforementioned race condition. The BTF resources
initialized by module initcall are set up once and then only looked
up, so just waiting until the initcall has finished ensures correct
behavior.
Syzbot has reported GPF in sg_alloc_append_table_from_pages(). The
problem was in ubuf->pages == ZERO_PTR.
ubuf->pagecount is calculated from arguments passed from user-space. If
user creates udmabuf with list.size == 0 then ubuf->pagecount will be
also equal to zero; it causes kmalloc_array() to return ZERO_PTR.
Fix it by validating ubuf->pagecount before passing it to
kmalloc_array().
After `bpftool gen skeleton`, the ${bpf_app}.skel.h will provide that
${bpf_app_name}__open helper to load bpf. If there is some error
like ENOMEM, the ${bpf_app_name}__open will rollback(free) the allocated
object, including `bpf_object_skeleton`.
Since the ${bpf_app_name}__create_skeleton set the obj->skeleton first
and not rollback it when error, it will cause double-free in
${bpf_app_name}__destory at ${bpf_app_name}__open. Therefore, we should
set the obj->skeleton before return 0;
projects / linux.git / log