ARM: dts: qcom: msm8974-oneplus-bacon: Add volume keys and hall sensor

Add nodes for the volume buttons and the hall sensor that are found on
the device.

Signed-off-by: Luca Weiss <luca@z3ntu.xyz>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230122-msm8974-bacon-features-v2-3-06bb83c20a58@z3ntu.xyz

ARM: dts: qcom: msm8974-oneplus-bacon: Add vibrator

Enable the pm8941 vibrator that's wired up on this device.

Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Luca Weiss <luca@z3ntu.xyz>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230122-msm8974-bacon-features-v2-2-06bb83c20a58@z3ntu.xyz

ARM: dts: qcom: pm8941: Add vibrator node

Add the node describing the vibrator that's found on pm8941.

Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Luca Weiss <luca@z3ntu.xyz>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230122-msm8974-bacon-features-v2-1-06bb83c20a58@z3ntu.xyz

ARM: dts: qcom: sdx55: correct TLMM gpio-ranges

Correct the number of GPIOs in TLMM pin controller.

Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230202104452.299048-9-krzysztof.kozlowski@linaro.org

dt-bindings: arm: qcom: add the sa8775p-ride board

Document the sa8775p SoC and its reference board: sa8775p-ride.

Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230201152038.203387-5-brgl@bgdev.pl

ARM: dts: qcom: apq8064: add second DSI host and PHY

Add second DSI host and PHY available on the APQ8064 platform.

Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230121091237.2734272-1-dmitry.baryshkov@linaro.org

ARM: dts: qcom: apq8060-dragonboard: align MPP pin node names with DT schema

DT schema expects nodes ending with "pins:

  qcom-apq8060-dragonboard.dtb: mpps@50: cm3605-mpps-state: 'oneOf' conditional failed, one must be fixed:
    'mpp5' does not match any of the regexes: '-pins$', 'pinctrl-[0-9]+'

Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230120174036.351937-1-krzysztof.kozlowski@linaro.org

dt-bindings: arm: qcom: Add Xiaomi Mi Pad 5 Pro (xiaomi-elish)

Add a compatible for Xiaomi Mi Pad 5 Pro.

Signed-off-by: Jianhua Lu <lujianhua000@gmail.com>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230131123515.833-1-lujianhua000@gmail.com

ARM: dts: qcom-sdx65: align RPMh regulator nodes with bindings

Device node names should be generic and bindings expect certain pattern
for RPMh regulator nodes.

Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230127114347.235963-2-krzysztof.kozlowski@linaro.org

ARM: dts: qcom-sdx55: align RPMh regulator nodes with bindings

Device node names should be generic and bindings expect certain pattern
for RPMh regulator nodes.

Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230127114347.235963-1-krzysztof.kozlowski@linaro.org

ARM: dts: qcom: use "okay" for status

"okay" over "ok" is preferred:

  serial@f991f000: status:0: 'ok' is not one of ['okay', 'disabled', 'reserved']

Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230127095319.64560-1-krzysztof.kozlowski@linaro.org

ARM: dts: qcom: sdx65: Add Qcom SMMU-500 as the fallback for IOMMU node

SDX65 uses the Qcom version of the SMMU-500 IP. So use "qcom,smmu-500"
compatible as the fallback to the SoC specific compatible.

Cc: <stable@vger.kernel.org> # 5.19
Fixes: 98187f7b74bf ("ARM: dts: qcom: sdx65: Enable ARM SMMU")
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230123131931.263024-4-manivannan.sadhasivam@linaro.org

ARM: dts: qcom: sdx55: Add Qcom SMMU-500 as the fallback for IOMMU node

SDX55 uses the Qcom version of the SMMU-500 IP. So use "qcom,smmu-500"
compatible as the fallback to the SoC specific compatible.

Cc: <stable@vger.kernel.org> # 5.12
Fixes: a2bdfdfba2af ("ARM: dts: qcom: sdx55: Enable ARM SMMU")
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230123131931.263024-3-manivannan.sadhasivam@linaro.org

ARM: dts: qcom: apq8064: use hdmi_phy for the MMCC's hdmipll clock

Link hdmi_phy as a clock provider of "hdmipll" clock to the MMCC.

Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230119132219.2479775-7-dmitry.baryshkov@linaro.org

ARM: dts: qcom: apq8064: add #clock-cells to the HDMI PHY node

Add #clock-cells property to the HDMI PHY device node to let other nodes
resolve the hdmipll clock.

Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230119132219.2479775-6-dmitry.baryshkov@linaro.org

ARM: dts: qcom: ipq8064: move reg-less nodes outside soc node

Move node that doesn't have a reg outside the soc node as it should only
contain reg nodes.
No changes intended.

Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230117224417.7530-1-ansuelsmth@gmail.com

dt-bindings: qcom: Document msm8916-thwc-uf896 and ufi001c

Document the new thwc,uf896/ufi001c device tree bindings used in their device
trees.

Signed-off-by: Yang Xiwen <forbidden405@foxmail.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>

dt-bindings: vendor-prefixes: add thwc

Shenzhen Tong Heng Wei Chuang Technology Co., Ltd. (hereinafter referred
to as "Tong Heng Wei Chuang") is a focus on wireless communications
equipment brand manufacturers.

Link: http://www.szthwc.com/en/about.html
Signed-off-by: Yang Xiwen <forbidden405@foxmail.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>

dt-bindings: arm: qcom: Document the sc7280 CRD Pro boards

Add compatibles for the Pro SKU of the sc7280 CRD boards
which come with a Pro variant of the qcard.
The Pro qcard variant has smps9 from pm8350c ganged up with
smps7 and smps8.

Signed-off-by: Rajendra Nayak <quic_rjendra@quicinc.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20221216112918.1243-1-quic_rjendra@quicinc.com

ARM: dts: qcom: msm8226: add RPMCC node

Add a node for the RPM Clock Controller on MSM8226.

Signed-off-by: Rayyan Ansari <rayyan@ansari.sh>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230118181343.438373-1-rayyan@ansari.sh

ARM: dts: qcom: apq8084: add clocks and clock-names to gcc device

Add clocks and clock-names nodes to the gcc device to bind clocks using
the DT links.

Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230111060402.1168726-13-dmitry.baryshkov@linaro.org

ARM: dts: qcom: align OPP table node name with DT schema

Bindings expect OPP tables to start with "opp-table".

Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230109112221.102473-1-krzysztof.kozlowski@linaro.org

ARM: dts: qcom: rename mdp nodes to display-controller

Follow the schema change and rename mdp nodes to generic name
'display-controller'.

Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230109051402.317577-7-dmitry.baryshkov@linaro.org

ARM: dts: qcom-msm8974: rename mdss node to display-subsystem

Follow the schema change and rename mdss node to generic name
'display-subsystem'.

Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230109051402.317577-5-dmitry.baryshkov@linaro.org

ARM: dts: qcom-msm8974: add SoC specific compat string to mdp5 node

Add SoC-specific compat string to the MDP5 device node to ease
distinguishing between various platforms.

Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230109050152.316606-4-dmitry.baryshkov@linaro.org

dt-bindings: qcom: Document samsung,gt58 and gt510

gt58 and gt510 are Samsung Galaxy Tab A 8.0/9.7 (2015) tablets.
Document their compatibles.

Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Nikita Travkin <nikita@trvn.ru>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230107141911.47229-2-nikita@trvn.ru

dt-bindings: qcom: Document bindings for msm8916-samsung-j5x

Document the new samsung-j5x device tree bindings used in its device tree.

Signed-off-by: Lin, Meng-Bo <linmengbo0689@protonmail.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230106142956.547081-1-linmengbo0689@protonmail.com

ARM: dts: qcom: use qcom,gsi-loader for IPA

Depending on the platform, either the modem or the AP must load GSI
firmware for IPA before it can be used.  To date, this has been
indicated by the presence or absence of a "modem-init" property.

That mechanism has been deprecated.  Instead, we indicate how GSI
firmware should be loaded by the value of the "qcom,gsi-loader"
property.

Update all ARM platforms that use IPA to use the "qcom,gsi-loader"
property to specify how the GSI firmware is loaded.

Update the affected nodes so the status property is last.

Signed-off-by: Alex Elder <elder@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20221231002716.2367375-2-elder@linaro.org

ARM: dts: qcom-apq8084: specify per-sensor calibration cells

Specify pre-parsed per-sensor calibration nvmem cells in the tsens
device node rather than parsing the whole data blob in the driver.

Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230101194034.831222-21-dmitry.baryshkov@linaro.org

ARM: dts: qcom-msm8974: specify per-sensor calibration cells

Specify pre-parsed per-sensor calibration nvmem cells in the tsens
device node rather than parsing the whole data blob in the driver.

Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230101194034.831222-20-dmitry.baryshkov@linaro.org

Merge tag 'qcom-dts-fixes-for-6.2' into dts-for-6.3

Qualcomm ARM32 DTS fix for 6.2

This fixes a regression on Inforce 6540, as the sdhci nodes no longer
overrides the platform's mmc nodes.

dt-bindings: arm: qcom: Document MSM8939 SoC binding

Document the MSM8939 and supported boards in upstream Sony "Tulip" M4 Aqua
and Square APQ8039 T2.

MSM8939 is one of the older SoCs so we need to expand the list of
qcom,board-ids to allow for the bootloader DTS board-id matching
dependency.

Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230117024846.1367794-2-bryan.odonoghue@linaro.org

ARM: dts: qcom: msm8974: add xo clock to rpm clock controller

Populate the rpm clock controller node with clocks and clock-names
properties.

Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20221227001547.2830656-1-dmitry.baryshkov@linaro.org

dt-bindings: qcom: Document msm8916-gplus-fl8005a

Document the new gplus,fl8005a device tree bindings used in its
device tree.

Signed-off-by: Lin, Meng-Bo <linmengbo0689@protonmail.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230107133158.139785-1-linmengbo0689@protonmail.com

dt-bindings: vendor-prefixes: Add GPLUS

Add vendor prefix for GPLUS.
https://www.gplus.com.tw

Signed-off-by: Lin, Meng-Bo <linmengbo0689@protonmail.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230107133145.139731-1-linmengbo0689@protonmail.com

ARM: dts: qcom: apq8026-samsung-matisse-wifi: Add display backlight

Uses ti,lp8556 backlight with clk-pwm.

Signed-off-by: Matti Lehtimäki <matti.lehtimaki@gmail.com>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230111183502.706151-1-matti.lehtimaki@gmail.com

dt-bindings: arm: qcom: Add SM6115(P) and Lenovo Tab P11

Document SM6115P, an APQ version of SM6115.

Document Lenovo Tab P11 (J606F) as a SM6115P device.

Add SM6115 to the msm-id list of shame.

Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Reviewed-by: Bhupesh Sharma <bhupesh.sharma@linaro.org>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20221208201401.530555-4-konrad.dybcio@linaro.org

ARM: dts: qcom: add missing space before {

Add missing whitespace between node name/label and opening {.

Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20221230140133.57885-1-krzysztof.kozlowski@linaro.org

dt-bindings: arm: qcom: add board-id/msm-id for MSM8956, SDM636 and SM4250

Allow qcom,board-id and qcom,msm-id leagcy properties on these older
platforms: MSM8956, SDM636 and SM4250.  Also mention more OnePlus
devices using modified qcom,board-id field.

Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Marijn Suijten <marijn.suijten@somainline.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20221214150605.173346-1-krzysztof.kozlowski@linaro.org

dt-bindings: arm: qcom: Add zombie with NVMe

Add entries in the device tree binding for sc7280-zombie with NVMe.

Signed-off-by: Owen Yang <ecs.taipeikernel@gmail.com>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20221214114706.1.Ie4ca64ad56748de5aacd36237d42c80dd003c1a9@changeid

ARM: dts: qcom: msm8960: add qcom,kpss-wdt-mdm9615

Add specific compatible to timer/watchdog device node.

Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20221212163532.142533-12-krzysztof.kozlowski@linaro.org

ARM: dts: qcom: msm8960: drop second clock frequency from timer

Keep only one clock frequency for timer, because:
1. DT schema does not allow multiple frequencies in such property,
2. The Linux timer driver reads only first frequency.

Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20221212163532.142533-11-krzysztof.kozlowski@linaro.org

ARM: dts: qcom: mdm9615: drop second clock frequency from timer

Keep only one clock frequency for timer, because:
1. DT schema does not allow multiple frequencies in such property,
2. The Linux timer driver reads only first frequency.

Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20221212163532.142533-10-krzysztof.kozlowski@linaro.org

ARM: dts: qcom: ipq8064: drop second clock frequency from timer

Keep only one clock frequency for timer, because:
1. DT schema does not allow multiple frequencies in such property,
2. The Linux timer driver reads only first frequency.

Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20221212163532.142533-9-krzysztof.kozlowski@linaro.org

ARM: dts: qcom: apq8064: drop second clock frequency from timer

Keep only one clock frequency for timer, because:
1. DT schema does not allow multiple frequencies in such property,
2. The Linux timer driver reads only first frequency.

Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20221212163532.142533-8-krzysztof.kozlowski@linaro.org

ARM: dts: qcom: reverse compatibles to match bindings

The most specific compatible should be upfront.

Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20221212163532.142533-7-krzysztof.kozlowski@linaro.org

dt-bindings: arm: qcom: Document SM8550 SoC and boards

Document the SM8550 SoC binding and the MTP board.

Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230106201047.337409-2-abel.vesa@linaro.org

ARM: dts: qcom: msm8974: Add compat qcom,msm8974-dsi-ctrl to dsi1

Extend the secon DSI interface with the SoC-specific compat entry,
following the change for the first DSI interface.

Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230110055433.734188-1-dmitry.baryshkov@linaro.org

ARM: dts: qcom: msm8974: Add compat qcom,msm8974-dsi-ctrl

Add silicon specific compatible qcom,msm8974-dsi-ctrl to the
mdss-dsi-ctrl block. This allows us to differentiate the specific bindings
for msm8974 against the yaml documentation.

Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20221223021025.1646636-10-bryan.odonoghue@linaro.org

ARM: dts: qcom: apq8064: add compat qcom,apq8064-dsi-ctrl

Append silicon specific compatible qcom,apq8064-dsi-ctrl to the
mdss-dsi-ctrl block. This allows us to differentiate the specific bindings
for apq8064 against the yaml documentation.

Reviewed-by: David Heidelberg <david@ixit.cz>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20221223021025.1646636-9-bryan.odonoghue@linaro.org

ARM: dts: qcom: sdx65: add specific compatible for USB HS PHY

Add SoC-specific compatible to the USB HS PHY to match other devices and
bindings.

Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20221223161835.112079-3-krzysztof.kozlowski@linaro.org

ARM: dts: qcom: sdx55: add specific compatible for USB HS PHY

Add SoC-specific compatible to the USB HS PHY to match other devices and
bindings.

Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20221223161835.112079-2-krzysztof.kozlowski@linaro.org

ARM: dts: qcom: apq8026-samsung-matisse-wifi: Enable ADSP

Configure the reserved memory for ADSP and enable it.
Delete nodes with reference to label.

Signed-off-by: Matti Lehtimäki <matti.lehtimaki@gmail.com>
Reviewed-by: Luca Weiss <luca@z3ntu.xyz>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20221218211957.118473-1-matti.lehtimaki@gmail.com

dt-bindings: arm: qcom: document new msm8953-family devices

Document the various phones added in upcoming patches. Also allow
qcom,msm-id and qcom,board-id for msm8953 and sdm450.

Signed-off-by: Luca Weiss <luca@z3ntu.xyz>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20221207-msm8953-6-1-next-dtbs-v3-v3-1-a64b3b0af0eb@z3ntu.xyz

ARM: dts: qcom: pm8226: add IADC node

Add a node for the current ADC (IADC) found in PM8226.

Signed-off-by: Rayyan Ansari <rayyan@ansari.sh>
[bjorn: Updated node name and added specific compatible, per request from Luca Weiss]
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20221223193403.781355-4-rayyan@ansari.sh

ARM: dts: qcom: pm8226: add PON device node along with resin sub-node

The PON (Power On) device in PM8226 supports both the power key and
resin (reset input).
The reset input is usually connected to a physical volume up/down button.

Signed-off-by: Rayyan Ansari <rayyan@ansari.sh>
Reviewed-by: Luca Weiss <luca@z3ntu.xyz>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20221223193403.781355-3-rayyan@ansari.sh

ARM: dts: qcom: pm8226: sort includes alphabetically and nodes by address

Sort the includes and nodes for consistency.

Signed-off-by: Rayyan Ansari <rayyan@ansari.sh>
Reviewed-by: Luca Weiss <luca@z3ntu.xyz>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20221223193403.781355-2-rayyan@ansari.sh

ARM: dts: qcom: msm8974: add clocks and clock-names to mmcc device

Add clocks and clock-names nodes to the mmcc device to bind clocks using
the DT links.

Reviewed-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20221204124508.1415713-12-dmitry.baryshkov@linaro.org

ARM: dts: qcom: msm8974: add clocks and clock-names to gcc device

Add clocks and clock-names nodes to the gcc device to bind clocks using
the DT links.

Reviewed-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20221204124508.1415713-11-dmitry.baryshkov@linaro.org

ARM: dts: qcom: msm8974: add second DSI host and PHY

Add second DSI host and PHY available on the msm8974 platform.

Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20221204124508.1415713-10-dmitry.baryshkov@linaro.org

ARM: dts: qcom: apq8084-ifc6540: fix overriding SDHCI

While changing node names of APQ8084 SDHCI, the ones in IFC6540 board
were not updated leading to disabled and misconfigured SDHCI.

Cc: <stable@vger.kernel.org>
Fixes: 2477d81901a2 ("ARM: dts: qcom: Fix sdhci node names - use 'mmc@'")
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20221204084614.12193-1-krzysztof.kozlowski@linaro.org

arm64: dts: qcom: msm8916-acer-a1-724: Add touchscreen

A1-724 uses a Focaltech FT5446 touchscreen that is connected to blsp_i2c5.
Add it to the device tree.

Signed-off-by: Lin, Meng-Bo <linmengbo0689@protonmail.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20221123033844.149115-1-linmengbo0689@protonmail.com

arm64: dts: qcom: msm8916-acer-a1-724: Add accelerometer/magnetometer

Iconia Talk S uses a Bosch BMC150 accelerometer/magnetometer combo.
The chip provides two separate I2C devices for the accelerometer
and magnetometer that are already supported by the bmc150-accel
and bmc150-magn driver.

Signed-off-by: Lin, Meng-Bo <linmengbo0689@protonmail.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20221123033830.149061-1-linmengbo0689@protonmail.com

arm64: dts: qcom: msm8916-acer-a1-724: Add initial device tree

Acer Iconia Talk S A1-724 is a tablet using the MSM8916 SoC released
in 2014.

Note: The original firmware from Acer can only boot 32-bit kernels.
To boot arm64 kernels it is necessary to flash 64-bit TZ/HYP firmware
with EDL, e.g. taken from the DragonBoard 410c. This works because Acer
didn't set up (firmware) secure boot.

Add a device tree for with initial support for:

- GPIO keys
- pm8916-vibrator
- SDHCI (internal and external storage)
- USB Device Mode
- UART
- WCNSS (WiFi/BT)
- Regulators

Signed-off-by: Lin, Meng-Bo <linmengbo0689@protonmail.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20221123033817.149007-1-linmengbo0689@protonmail.com

dt-bindings: qcom: Document msm8916-acer-a1-724

Document the new acer,a1-724 device tree bindings used in its device tree.

Signed-off-by: Lin, Meng-Bo <linmengbo0689@protonmail.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20221123033804.148953-1-linmengbo0689@protonmail.com

ARM: dts: qcom: msm8974-castor: Enable charging over USB

Set usb-charge-current-limit to higher value so that the device can be
charged over USB.

Signed-off-by: Julian Weigt <juw@posteo.de>
Signed-off-by: Luca Weiss <luca@z3ntu.xyz>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20221121213019.324558-2-luca@z3ntu.xyz

ARM: dts: qcom: msm8974-castor: Fix touchscreen init

On some devices a higher delay is needed, otherwise touchscreen probe
fails.

Signed-off-by: Luca Weiss <luca@z3ntu.xyz>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20221121213019.324558-1-luca@z3ntu.xyz

ARM: dts: qcom: msm8974-*: re-add remoteproc supplies

As part of a recent cleanup commit, the remoteproc supplies for adsp and
modem were removed from msm8974.dtsi and now need to be set in the
device dts. Do so.

Fixes: f300826d27be ("ARM: dts: qcom-msm8974: Sort and clean up nodes")
Signed-off-by: Luca Weiss <luca@z3ntu.xyz>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20221121212226.321514-2-luca@z3ntu.xyz

ARM: dts: msm8974: castor: Define pm8841 regulators

Define the pm8841 regulators under SMD/RPM, to allow the modem
remoteproc to set the voltage during boot of the remote processor.

Entries are just copied from the Honami dts.

Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Luca Weiss <luca@z3ntu.xyz>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20221121212226.321514-1-luca@z3ntu.xyz

ARM: dts: qcom: sdx55-mtp: add MPSS remoteproc memory-region

The MPSS PAS remoteproc bindings require memory-region.  The MPSS PAS
device node is disabled, but schema still asks for it.

Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20221118113747.56700-1-krzysztof.kozlowski@linaro.org

Linux 6.2-rc1

treewide: Convert del_timer*() to timer_shutdown*()

Due to several bugs caused by timers being re-armed after they are
shutdown and just before they are freed, a new state of timers was added
called "shutdown".  After a timer is set to this state, then it can no
longer be re-armed.

The following script was run to find all the trivial locations where
del_timer() or del_timer_sync() is called in the same function that the
object holding the timer is freed.  It also ignores any locations where
the timer->function is modified between the del_timer*() and the free(),
as that is not considered a "trivial" case.

This was created by using a coccinelle script and the following
commands:

    $ cat timer.cocci
    @@
    expression ptr, slab;
    identifier timer, rfield;
    @@
    (
    -       del_timer(&ptr->timer);
    +       timer_shutdown(&ptr->timer);
    |
    -       del_timer_sync(&ptr->timer);
    +       timer_shutdown_sync(&ptr->timer);
    )
      ... when strict
          when != ptr->timer
    (
            kfree_rcu(ptr, rfield);
    |
            kmem_cache_free(slab, ptr);
    |
            kfree(ptr);
    )

    $ spatch timer.cocci . > /tmp/t.patch
    $ patch -p1 < /tmp/t.patch

Link: https://lore.kernel.org/lkml/20221123201306.823305113@linutronix.de/
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
Acked-by: Pavel Machek <pavel@ucw.cz> [ LED ]
Acked-by: Kalle Valo <kvalo@kernel.org> [ wireless ]
Acked-by: Paolo Abeni <pabeni@redhat.com> [ networking ]
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Merge tag 'spi-fix-v6.2-rc1' of git://git./linux/kernel/git/broonie/spi

Pull spi fix from Mark Brown:
 "One driver specific change here which handles the case where a SPI
  device for some reason tries to change the bus speed during a message
  on fsl_spi hardware, this should be very unusual"

* tag 'spi-fix-v6.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi:
  spi: fsl_spi: Don't change speed while chipselect is active

Merge tag 'regulator-fix-v6.2-rc1' of git://git./linux/kernel/git/broonie/regulator

Pull regulator fixes from Mark Brown:
 "Two core fixes here, one for a long standing race which some Qualcomm
  systems have started triggering with their UFS driver and another
  fixing a problem with supply lookup introduced by the fixes for devm
  related use after free issues that were introduced in this merge
  window"

* tag 'regulator-fix-v6.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator:
  regulator: core: fix deadlock on regulator enable
  regulator: core: Fix resolve supply lookup issue

Merge tag 'coccinelle-6.2' of git://git./linux/kernel/git/jlawall/linux

Pull coccicheck update from Julia Lawall:
 "Modernize use of grep in coccicheck:

  Use 'grep -E' instead of 'egrep'"

* tag 'coccinelle-6.2' of git://git.kernel.org/pub/scm/linux/kernel/git/jlawall/linux:
  scripts: coccicheck: use "grep -E" instead of "egrep"

Merge tag 'hardening-v6.2-rc1-fixes' of git://git./linux/kernel/git/kees/linux

Pull kernel hardening fixes from Kees Cook:

 - Fix CFI failure with KASAN (Sami Tolvanen)

 - Fix LKDTM + CFI under GCC 7 and 8 (Kristina Martsenko)

 - Limit CONFIG_ZERO_CALL_USED_REGS to Clang > 15.0.6 (Nathan
   Chancellor)

 - Ignore "contents" argument in LoadPin's LSM hook handling

 - Fix paste-o in /sys/kernel/warn_count API docs

 - Use READ_ONCE() consistently for oops/warn limit reading

* tag 'hardening-v6.2-rc1-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux:
  cfi: Fix CFI failure with KASAN
  exit: Use READ_ONCE() for all oops/warn limit reads
  security: Restrict CONFIG_ZERO_CALL_USED_REGS to gcc or clang > 15.0.6
  lkdtm: cfi: Make PAC test work with GCC 7 and 8
  docs: Fix path paste-o for /sys/kernel/warn_count
  LoadPin: Ignore the "contents" argument of the LSM hooks

Merge tag 'pstore-v6.2-rc1-fixes' of git://git./linux/kernel/git/kees/linux

Pull pstore fixes from Kees Cook:

 - Switch pmsg_lock to an rt_mutex to avoid priority inversion (John
   Stultz)

 - Correctly assign mem_type property (Luca Stefani)

* tag 'pstore-v6.2-rc1-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux:
  pstore: Properly assign mem_type property
  pstore: Make sure CONFIG_PSTORE_PMSG selects CONFIG_RT_MUTEXES
  pstore: Switch pmsg_lock to an rt_mutex to avoid priority inversion

Merge tag 'dma-mapping-2022-12-23' of git://git.infradead.org/users/hch/dma-mapping

Pull dma-mapping fixes from Christoph Hellwig:
 "Fix up the sound code to not pass __GFP_COMP to the non-coherent DMA
  allocator, as it copes with that just as badly as the coherent
  allocator, and then add a check to make sure no one passes the flag
  ever again"

* tag 'dma-mapping-2022-12-23' of git://git.infradead.org/users/hch/dma-mapping:
  dma-mapping: reject GFP_COMP for noncoherent allocations
  ALSA: memalloc: don't use GFP_COMP for non-coherent dma allocations

Merge tag '9p-for-6.2-rc1' of https://github.com/martinetd/linux

Pull 9p updates from Dominique Martinet:

 - improve p9_check_errors to check buffer size instead of msize when
   possible (e.g. not zero-copy)

 - some more syzbot and KCSAN fixes

 - minor headers include cleanup

* tag '9p-for-6.2-rc1' of https://github.com/martinetd/linux:
  9p/client: fix data race on req->status
  net/9p: fix response size check in p9_check_errors()
  net/9p: distinguish zero-copy requests
  9p/xen: do not memcpy header into req->rc
  9p: set req refcount to zero to avoid uninitialized usage
  9p/net: Remove unneeded idr.h #include
  9p/fs: Remove unneeded idr.h #include

Merge tag 'sound-6.2-rc1-2' of git://git./linux/kernel/git/tiwai/sound

Pull more sound updates from Takashi Iwai:
 "A few more updates for 6.2: most of changes are about ASoC
  device-specific fixes.

   - Lots of ASoC Intel AVS extensions and refactoring

   - Quirks for ASoC Intel SOF as well as regression fixes

   - ASoC Mediatek and Rockchip fixes

   - Intel HD-audio HDMI workarounds

   - Usual HD- and USB-audio device-specific quirks"

* tag 'sound-6.2-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (54 commits)
  ALSA: usb-audio: Add new quirk FIXED_RATE for JBL Quantum810 Wireless
  ALSA: azt3328: Remove the unused function snd_azf3328_codec_outl()
  ASoC: lochnagar: Fix unused lochnagar_of_match warning
  ASoC: Intel: Add HP Stream 8 to bytcr_rt5640.c
  ASoC: SOF: mediatek: initialize panic_info to zero
  ASoC: rt5670: Remove unbalanced pm_runtime_put()
  ASoC: Intel: bytcr_rt5640: Add quirk for the Advantech MICA-071 tablet
  ASoC: Intel: soc-acpi: update codec addr on 0C11/0C4F product
  ASoC: rockchip: spdif: Add missing clk_disable_unprepare() in rk_spdif_runtime_resume()
  ASoC: wm8994: Fix potential deadlock
  ASoC: mediatek: mt8195: add sof be ops to check audio active
  ASoC: SOF: Revert: "core: unregister clients and machine drivers in .shutdown"
  ASoC: SOF: Intel: pci-tgl: unblock S5 entry if DMA stop has failed"
  ALSA: hda/hdmi: fix stream-id config keep-alive for rt suspend
  ALSA: hda/hdmi: set default audio parameters for KAE silent-stream
  ALSA: hda/hdmi: fix i915 silent stream programming flow
  ALSA: hda: Error out if invalid stream is being setup
  ASoC: dt-bindings: fsl-sai: Reinstate i.MX93 SAI compatible string
  ASoC: soc-pcm.c: Clear DAIs parameters after stream_active is updated
  ASoC: codecs: wcd-clsh: Remove the unused function
  ...

Merge tag 'drm-next-2022-12-23' of git://anongit.freedesktop.org/drm/drm

Pull drm fixes from Dave Airlie:
 "Holiday fixes!

  Two batches from amd, and one group of i915 changes.

  amdgpu:
   - Spelling fix
   - BO pin fix
   - Properly handle polaris 10/11 overlap asics
   - GMC9 fix
   - SR-IOV suspend fix
   - DCN 3.1.4 fix
   - KFD userptr locking fix
   - SMU13.x fixes
   - GDS/GWS/OA handling fix
   - Reserved VMID handling fixes
   - FRU EEPROM fix
   - BO validation fixes
   - Avoid large variable on the stack
   - S0ix fixes
   - SMU 13.x fixes
   - VCN fix
   - Add missing fence reference

  amdkfd:
   - Fix init vm error handling
   - Fix double release of compute pasid

  i915
   - Documentation fixes
   - OA-perf related fix
   - VLV/CHV HDMI/DP audio fix
   - Display DDI/Transcoder fix
   - Migrate fixes"

* tag 'drm-next-2022-12-23' of git://anongit.freedesktop.org/drm/drm: (39 commits)
  drm/amdgpu: grab extra fence reference for drm_sched_job_add_dependency
  drm/amdgpu: enable VCN DPG for GC IP v11.0.4
  drm/amdgpu: skip mes self test after s0i3 resume for MES IP v11.0
  drm/amd/pm: correct the fan speed retrieving in PWM for some SMU13 asics
  drm/amd/pm: bump SMU13.0.0 driver_if header to version 0x34
  drm/amdgpu: skip MES for S0ix as well since it's part of GFX
  drm/amd/pm: avoid large variable on kernel stack
  drm/amdkfd: Fix double release compute pasid
  drm/amdkfd: Fix kfd_process_device_init_vm error handling
  drm/amd/pm: update SMU13.0.0 reported maximum shader clock
  drm/amd/pm: correct SMU13.0.0 pstate profiling clock settings
  drm/amd/pm: enable GPO dynamic control support for SMU13.0.7
  drm/amd/pm: enable GPO dynamic control support for SMU13.0.0
  drm/amdgpu: revert "generally allow over-commit during BO allocation"
  drm/amdgpu: Remove unnecessary domain argument
  drm/amdgpu: Fix size validation for non-exclusive domains (v4)
  drm/amdgpu: Check if fru_addr is not NULL (v2)
  drm/i915/ttm: consider CCS for backup objects
  drm/i915/migrate: fix corner case in CCS aux copying
  drm/amdgpu: rework reserved VMID handling
  ...

Merge tag 'mips_6.2_1' of git://git./linux/kernel/git/mips/linux

Pull MIPS fixes from Thomas Bogendoerfer:
 "Fixes due to DT changes"

* tag 'mips_6.2_1' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux:
  MIPS: dts: bcm63268: Add missing properties to the TWD node
  MIPS: ralink: mt7621: avoid to init common ralink reset controller

Merge tag 'mm-hotfixes-stable-2022-12-22-14-34' of git://git./linux/kernel/git/akpm/mm

Pull hotfixes from Andrew Morton:
 "Eight fixes, all cc:stable. One is for gcov and the remainder are MM"

* tag 'mm-hotfixes-stable-2022-12-22-14-34' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm:
  gcov: add support for checksum field
  test_maple_tree: add test for mas_spanning_rebalance() on insufficient data
  maple_tree: fix mas_spanning_rebalance() on insufficient data
  hugetlb: really allocate vma lock for all sharable vmas
  kmsan: export kmsan_handle_urb
  kmsan: include linux/vmalloc.h
  mm/mempolicy: fix memory leak in set_mempolicy_home_node system call
  mm, mremap: fix mremap() expanding vma with addr inside vma

pstore: Properly assign mem_type property

If mem-type is specified in the device tree
it would end up overriding the record_size
field instead of populating mem_type.

As record_size is currently parsed after the
improper assignment with default size 0 it
continued to work as expected regardless of the
value found in the device tree.

Simply changing the target field of the struct
is enough to get mem-type working as expected.

Fixes: 9d843e8fafc7 ("pstore: Add mem_type property DT parsing support")
Cc: stable@vger.kernel.org
Signed-off-by: Luca Stefani <luca@osomprivacy.com>
Signed-off-by: Kees Cook <keescook@chromium.org>
Link: https://lore.kernel.org/r/20221222131049.286288-1-luca@osomprivacy.com

pstore: Make sure CONFIG_PSTORE_PMSG selects CONFIG_RT_MUTEXES

In commit 76d62f24db07 ("pstore: Switch pmsg_lock to an rt_mutex
to avoid priority inversion") I changed a lock to an rt_mutex.

However, its possible that CONFIG_RT_MUTEXES is not enabled,
which then results in a build failure, as the 0day bot detected:
  https://lore.kernel.org/linux-mm/202212211244.TwzWZD3H-lkp@intel.com/

Thus this patch changes CONFIG_PSTORE_PMSG to select
CONFIG_RT_MUTEXES, which ensures the build will not fail.

Cc: Wei Wang <wvw@google.com>
Cc: Midas Chien<midaschieh@google.com>
Cc: Connor O'Brien <connoro@google.com>
Cc: Kees Cook <keescook@chromium.org>
Cc: Anton Vorontsov <anton@enomsg.org>
Cc: Colin Cross <ccross@android.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: kernel test robot <lkp@intel.com>
Cc: kernel-team@android.com
Fixes: 76d62f24db07 ("pstore: Switch pmsg_lock to an rt_mutex to avoid priority inversion")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: John Stultz <jstultz@google.com>
Signed-off-by: Kees Cook <keescook@chromium.org>
Link: https://lore.kernel.org/r/20221221051855.15761-1-jstultz@google.com

cfi: Fix CFI failure with KASAN

When CFI_CLANG and KASAN are both enabled, LLVM doesn't generate a
CFI type hash for asan.module_ctor functions in translation units
where CFI is disabled, which leads to a CFI failure during boot when
do_ctors calls the affected constructors:

  CFI failure at do_basic_setup+0x64/0x90 (target:
  asan.module_ctor+0x0/0x28; expected type: 0xa540670c)

Specifically, this happens because CFI is disabled for
kernel/cfi.c. There's no reason to keep CFI disabled here anymore, so
fix the failure by not filtering out CC_FLAGS_CFI for the file.

Note that https://reviews.llvm.org/rG3b14862f0a96 fixed the issue
where LLVM didn't emit CFI type hashes for any sanitizer constructors,
but now type hashes are emitted correctly for TUs that use CFI.

Link: https://github.com/ClangBuiltLinux/linux/issues/1742
Fixes: 89245600941e ("cfi: Switch to -fsanitize=kcfi")
Reported-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Sami Tolvanen <samitolvanen@google.com>
Signed-off-by: Kees Cook <keescook@chromium.org>
Link: https://lore.kernel.org/r/20221222225747.3538676-1-samitolvanen@google.com

Merge tag 'scsi-misc' of git://git./linux/kernel/git/jejb/scsi

Pull more SCSI updates from James Bottomley:
 "Mostly small bug fixes and small updates.

  The only things of note is a qla2xxx fix for crash on hotplug and
  timeout and the addition of a user exposed abstraction layer for
  persistent reservation error return handling (which necessitates the
  conversion of nvme.c as well as SCSI)"

* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
  scsi: qla2xxx: Fix crash when I/O abort times out
  nvme: Convert NVMe errors to PR errors
  scsi: sd: Convert SCSI errors to PR errors
  scsi: core: Rename status_byte to sg_status_byte
  block: Add error codes for common PR failures
  scsi: sd: sd_zbc: Trace zone append emulation
  scsi: libfc: Include the correct header

Merge tag 'afs-next-20221222' of git://git./linux/kernel/git/dhowells/linux-fs

Pull afs update from David Howells:
 "A fix for a couple of missing resource counter decrements, two small
  cleanups of now-unused bits of code and a patch to remove writepage
  support from afs"

* tag 'afs-next-20221222' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-fs:
  afs: Stop implementing ->writepage()
  afs: remove afs_cache_netfs and afs_zap_permits() declarations
  afs: remove variable nr_servers
  afs: Fix lost servers_outstanding count

Merge tag 'perf-tools-for-v6.2-2-2022-12-22' of git://git./linux/kernel/git/acme/linux

Pull more perf tools updates from Arnaldo Carvalho de Melo:
 "perf tools fixes and improvements:

   - Don't stop building perf if python setuptools isn't installed, just
     disable the affected perf feature.

   - Remove explicit reference to python 2.x devel files, that warning
     is about python-devel, no matter what version, being unavailable
     and thus disabling the linking with libpython.

   - Don't use -Werror=switch-enum when building the python support that
     handles libtraceevent enumerations, as there is no good way to test
     if some specific enum entry is available with the libtraceevent
     installed on the system.

   - Introduce 'perf lock contention' --type-filter and --lock-filter,
     to filter by lock type and lock name:

        $ sudo ./perf lock record -a -- ./perf bench sched messaging

        $ sudo ./perf lock contention -E 5 -Y spinlock
         contended  total wait   max wait  avg wait      type  caller

               802     1.26 ms   11.73 us   1.58 us  spinlock  __wake_up_common_lock+0x62
                13   787.16 us  105.44 us  60.55 us  spinlock  remove_wait_queue+0x14
                12   612.96 us   78.70 us  51.08 us  spinlock  prepare_to_wait+0x27
               114   340.68 us   12.61 us   2.99 us  spinlock  try_to_wake_up+0x1f5
                83   226.38 us    9.15 us   2.73 us  spinlock  folio_lruvec_lock_irqsave+0x5e

        $ sudo ./perf lock contention -l
         contended  total wait  max wait  avg wait           address  symbol

                57     1.11 ms  42.83 us  19.54 us  ffff9f4140059000
                15   280.88 us  23.51 us  18.73 us  ffffffff9d007a40  jiffies_lock
                 1    20.49 us  20.49 us  20.49 us  ffffffff9d0d50c0  rcu_state
                 1     9.02 us   9.02 us   9.02 us  ffff9f41759e9ba0

        $ sudo ./perf lock contention -L jiffies_lock,rcu_state
         contended  total wait  max wait  avg wait      type  caller

                15   280.88 us  23.51 us  18.73 us  spinlock  tick_sched_do_timer+0x93
                 1    20.49 us  20.49 us  20.49 us  spinlock  __softirqentry_text_start+0xeb

        $ sudo ./perf lock contention -L ffff9f4140059000
         contended  total wait  max wait  avg wait      type  caller

                38   779.40 us  42.83 us  20.51 us  spinlock  worker_thread+0x50
                11   216.30 us  39.87 us  19.66 us  spinlock  queue_work_on+0x39
                 8   118.13 us  20.51 us  14.77 us  spinlock  kthread+0xe5

   - Fix splitting CC into compiler and options when checking if a
     option is present in clang to build the python binding, needed in
     systems such as yocto that set CC to, e.g.: "gcc --sysroot=/a/b/c".

   - Refresh metris and events for Intel systems: alderlake.
     alderlake-n, bonnell, broadwell, broadwellde, broadwellx,
     cascadelakex, elkhartlake, goldmont, goldmontplus, haswell,
     haswellx, icelake, icelakex, ivybridge, ivytown, jaketown,
     knightslanding, meteorlake, nehalemep, nehalemex, sandybridge,
     sapphirerapids, silvermont, skylake, skylakex, snowridgex,
     tigerlake, westmereep-dp, westmereep-sp, westmereex.

   - Add vendor events files (JSON) for AMD Zen 4, from sections
     2.1.15.4 "Core Performance Monitor Counters", 2.1.15.5 "L3 Cache
     Performance Monitor Counter"s and Section 7.1 "Fabric Performance
     Monitor Counter (PMC) Events" in the Processor Programming
     Reference (PPR) for AMD Family 19h Model 11h Revision B1
     processors.

     This constitutes events which capture op dispatch, execution and
     retirement, branch prediction, L1 and L2 cache activity, TLB
     activity, L3 cache activity and data bandwidth for various links
     and interfaces in the Data Fabric.

   - Also, from the same PPR are metrics taken from Section 2.1.15.2
     "Performance Measurement", including pipeline utilization, which
     are new to Zen 4 processors and useful for finding performance
     bottlenecks by analyzing activity at different stages of the
     pipeline.

   - Greatly improve the 'srcline', 'srcline_from', 'srcline_to' and
     'srcfile' sort keys performance by postponing calling the external
     addr2line utility to the collapse phase of histogram bucketing.

   - Fix 'perf test' "all PMU test" to skip parametrized events, that
     requires setting up and are not supported by this test.

   - Update tools/ copies of kernel headers: features,
     disabled-features, fscrypt.h, i915_drm.h, msr-index.h, power pc
     syscall table and kvm.h.

   - Add .DELETE_ON_ERROR special Makefile target to clean up partially
     updated files on error.

   - Simplify the mksyscalltbl script for arm64 by avoiding to run the
     host compiler to create the syscall table, do it all just with the
     shell script.

   - Further fixes to honour quiet mode (-q)"

* tag 'perf-tools-for-v6.2-2-2022-12-22' of git://git.kernel.org/pub/scm/linux/kernel/git/acme/linux: (67 commits)
  perf python: Fix splitting CC into compiler and options
  perf scripting python: Don't be strict at handling libtraceevent enumerations
  perf arm64: Simplify mksyscalltbl
  perf build: Remove explicit reference to python 2.x devel files
  perf vendor events amd: Add Zen 4 mapping
  perf vendor events amd: Add Zen 4 metrics
  perf vendor events amd: Add Zen 4 uncore events
  perf vendor events amd: Add Zen 4 core events
  perf vendor events intel: Refresh westmereex events
  perf vendor events intel: Refresh westmereep-sp events
  perf vendor events intel: Refresh westmereep-dp events
  perf vendor events intel: Refresh tigerlake metrics and events
  perf vendor events intel: Refresh snowridgex events
  perf vendor events intel: Refresh skylakex metrics and events
  perf vendor events intel: Refresh skylake metrics and events
  perf vendor events intel: Refresh silvermont events
  perf vendor events intel: Refresh sapphirerapids metrics and events
  perf vendor events intel: Refresh sandybridge metrics and events
  perf vendor events intel: Refresh nehalemex events
  perf vendor events intel: Refresh nehalemep events
  ...

perf python: Fix splitting CC into compiler and options

Noticed this build failure on archlinux:base when building with clang:

  clang-14: error: optimization flag '-ffat-lto-objects' is not supported [-Werror,-Wignored-optimization-argument]

In tools/perf/util/setup.py we check if clang supports that option, but
since commit 3cad53a6f9cdbafa ("perf python: Account for multiple words
in CC") this got broken as in the common case where CC="clang":

  >>> cc="clang"
  >>> print(cc.split()[0])
  clang
  >>> option="-ffat-lto-objects"
  >>> print(str(cc.split()[1:]) + option)
  []-ffat-lto-objects
  >>>

And then the Popen will call clang with that bogus option name that in
turn will not produce the b"unknown argument" or b"is not supported"
that this function uses to detect if the option is not available and
thus later on clang will be called with an unknown/unsupported option.

Fix it by looking if really there are options in the provided CC
variable, and if so override 'cc' with the first token and append the
options to the 'option' variable.

Fixes: 3cad53a6f9cdbafa ("perf python: Account for multiple words in CC")
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Fangrui Song <maskray@google.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Ian Rogers <irogers@google.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: John Keeping <john@metanate.com>
Cc: Khem Raj <raj.khem@gmail.com>
Cc: Leo Yan <leo.yan@linaro.org>
Cc: Michael Petlan <mpetlan@redhat.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Nathan Chancellor <nathan@kernel.org>
Cc: Nick Desaulniers <ndesaulniers@google.com>
Cc: Sedat Dilek <sedat.dilek@gmail.com>
Link: http://lore.kernel.org/lkml/Y6Rq5F5NI0v1QQHM@kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>

afs: Stop implementing ->writepage()

We're trying to get rid of the ->writepage() hook[1].  Stop afs from using
it by unlocking the page and calling afs_writepages_region() rather than
folio_write_one().

A flag is passed to afs_writepages_region() to indicate that it should only
write a single region so that we don't flush the entire file in
->write_begin(), but do add other dirty data to the region being written to
try and reduce the number of RPC ops.

This requires ->migrate_folio() to be implemented, so point that at
filemap_migrate_folio() for files and also for symlinks and directories.

This can be tested by turning on the afs_folio_dirty tracepoint and then
doing something like:

   xfs_io -c "w 2223 7000" -c "w 15000 22222" -c "w 23 7" /afs/my/test/foo

and then looking in the trace to see if the write at position 15000 gets
stored before page 0 gets dirtied for the write at position 23.

Signed-off-by: David Howells <dhowells@redhat.com>
cc: Marc Dionne <marc.dionne@auristor.com>
cc: Christoph Hellwig <hch@lst.de>
cc: Matthew Wilcox <willy@infradead.org>
cc: linux-afs@lists.infradead.org
Link: https://lore.kernel.org/r/20221113162902.883850-1-hch@lst.de/
Link: https://lore.kernel.org/r/166876785552.222254.4403222906022558715.stgit@warthog.procyon.org.uk/

afs: remove afs_cache_netfs and afs_zap_permits() declarations

afs_zap_permits() has been removed since
commit be080a6f43c4 ("afs: Overhaul permit caching").

afs_cache_netfs has been removed since
commit 523d27cda149 ("afs: Convert afs to use the new fscache API").

so remove the declare for them from header file.

Signed-off-by: Gaosheng Cui <cuigaosheng1@huawei.com>
Signed-off-by: David Howells <dhowells@redhat.com>
cc: Marc Dionne <marc.dionne@auristor.com>
cc: linux-afs@lists.infradead.org
Link: https://lore.kernel.org/r/20220909070353.1160228-1-cuigaosheng1@huawei.com/

afs: remove variable nr_servers

Variable nr_servers is no longer being used, the last reference
to it was removed in commit 45df8462730d ("afs: Fix server list handling")
so clean up the code by removing it.

Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Signed-off-by: David Howells <dhowells@redhat.com>
cc: Marc Dionne <marc.dionne@auristor.com>
cc: linux-afs@lists.infradead.org
Link: https://lore.kernel.org/r/20221020173923.21342-1-colin.i.king@gmail.com/

afs: Fix lost servers_outstanding count

The afs_fs_probe_dispatcher() work function is passed a count on
net->servers_outstanding when it is scheduled (which may come via its
timer).  This is passed back to the work_item, passed to the timer or
dropped at the end of the dispatcher function.

But, at the top of the dispatcher function, there are two checks which
skip the rest of the function: if the network namespace is being destroyed
or if there are no fileservers to probe.  These two return paths, however,
do not drop the count passed to the dispatcher, and so, sometimes, the
destruction of a network namespace, such as induced by rmmod of the kafs
module, may get stuck in afs_purge_servers(), waiting for
net->servers_outstanding to become zero.

Fix this by adding the missing decrements in afs_fs_probe_dispatcher().

Fixes: f6cbb368bcb0 ("afs: Actively poll fileservers to maintain NAT or firewall openings")
Reported-by: Marc Dionne <marc.dionne@auristor.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Tested-by: Marc Dionne <marc.dionne@auristor.com>
cc: linux-afs@lists.infradead.org
Link: https://lore.kernel.org/r/167164544917.2072364.3759519569649459359.stgit@warthog.procyon.org.uk/

Merge tag 'asoc-v6.2-3' of https://git./linux/kernel/git/broonie/sound into for-linus

ASoC: Updates for v6.2

Some more small fixes and board quirks that came in since my last
update, the main one being the fixes from Kai for issues around the
attempts to get kexec working well on SOF based systems.

ALSA: usb-audio: Add new quirk FIXED_RATE for JBL Quantum810 Wireless

It seems that the firmware is broken and does not accept
the UAC_EP_CS_ATTR_SAMPLE_RATE URB. There is only one rate (48000Hz)
available in the descriptors for the output endpoint.

Create a new quirk QUIRK_FLAG_FIXED_RATE to skip the rate setup
when only one rate is available (fixed).

BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=216798
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Link: https://lore.kernel.org/r/20221215153037.1163786-1-perex@perex.cz
Signed-off-by: Takashi Iwai <tiwai@suse.de>

ALSA: azt3328: Remove the unused function snd_azf3328_codec_outl()

The function snd_azf3328_codec_outl is defined in the azt3328.c file, but
not called elsewhere, so remove this unused function.

sound/pci/azt3328.c:367:1: warning: unused function 'snd_azf3328_codec_outl'.

Link: https://bugzilla.openanolis.cn/show_bug.cgi?id=3432
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: Jiapeng Chong <jiapeng.chong@linux.alibaba.com>
Link: https://lore.kernel.org/r/20221213061355.62856-1-jiapeng.chong@linux.alibaba.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>

Merge branch 'for-next' into for-linus

Merge tag 'trace-v6.2-1' of git://git./linux/kernel/git/trace/linux-trace

Pull tracing fix from Steven Rostedt:
 "I missed this minor hardening of the kernel in the first pull.

   - Make monitor structures read only"

* tag 'trace-v6.2-1' of git://git.kernel.org/pub/scm/linux/kernel/git/trace/linux-trace:
  rv/monitors: Move monitor structure in rodata

Merge tag 'trace-probes-v6.2' of git://git./linux/kernel/git/trace/linux-trace

Pull trace probes updates from Steven Rostedt:

 - New "symstr" type for dynamic events that writes the name of the
   function+offset into the ring buffer and not just the address

 - Prevent kernel symbol processing on addresses in user space probes
   (uprobes).

 - And minor fixes and clean ups

* tag 'trace-probes-v6.2' of git://git.kernel.org/pub/scm/linux/kernel/git/trace/linux-trace:
  tracing/probes: Reject symbol/symstr type for uprobe
  tracing/probes: Add symstr type for dynamic events
  kprobes: kretprobe events missing on 2-core KVM guest
  kprobes: Fix check for probe enabled in kill_kprobe()
  test_kprobes: Fix implicit declaration error of test_kprobes
  tracing: Fix race where eprobes can be called before the event