Stefan Hajnoczi [Thu, 13 Oct 2022 18:59:01 +0000 (14:59 -0400)]
block: add BDRV_REQ_REGISTERED_BUF request flag
Block drivers may optimize I/O requests accessing buffers previously
registered with bdrv_register_buf(). Checking whether all elements of a
request's QEMUIOVector are within previously registered buffers is
expensive, so we need a hint from the user to avoid costly checks.
Add a BDRV_REQ_REGISTERED_BUF request flag to indicate that all
QEMUIOVector elements in an I/O request are known to be within
previously registered buffers.
Always pass the flag through to driver read/write functions. There is
little harm in passing the flag to a driver that does not use it.
Passing the flag to drivers avoids changes across many block drivers.
Filter drivers would need to explicitly support the flag and pass
through to their children when the children support it. That's a lot of
code changes and it's hard to remember to do that everywhere, leading to
silent reduced performance when the flag is accidentally dropped.
The only problematic scenario with the approach in this patch is when a
driver passes the flag through to internal I/O requests that don't use
the same I/O buffer. In that case the hint may be set when it should
actually be clear. This is a rare case though so the risk is low.
Some drivers have assert(!flags), which no longer works when
BDRV_REQ_REGISTERED_BUF is passed in. These assertions aren't very
useful anyway since the functions are called almost exclusively by
bdrv_driver_preadv/pwritev() so if we get flags handling right there
then the assertion is not needed.
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 20221013185908.1297568-7-stefanha@redhat.com Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Stefan Hajnoczi [Thu, 13 Oct 2022 18:58:59 +0000 (14:58 -0400)]
block: pass size to bdrv_unregister_buf()
The only implementor of bdrv_register_buf() is block/nvme.c, where the
size is not needed when unregistering a buffer. This is because
util/vfio-helpers.c can look up mappings by address.
Future block drivers that implement bdrv_register_buf() may not be able
to do their job given only the buffer address. Add a size argument to
bdrv_unregister_buf().
Also document the assumptions about
bdrv_register_buf()/bdrv_unregister_buf() calls. The same <host, size>
values that were given to bdrv_register_buf() must be given to
bdrv_unregister_buf().
gcc 11.2.1 emits a spurious warning that img_bench()'s buf_size local
variable might be uninitialized, so it's necessary to silence the
compiler.
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com> Reviewed-by: Stefano Garzarella <sgarzare@redhat.com>
Message-id: 20221013185908.1297568-5-stefanha@redhat.com Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Stefan Hajnoczi [Thu, 13 Oct 2022 18:58:58 +0000 (14:58 -0400)]
numa: call ->ram_block_removed() in ram_block_notifer_remove()
When a RAMBlockNotifier is added, ->ram_block_added() is called with all
existing RAMBlocks. There is no equivalent ->ram_block_removed() call
when a RAMBlockNotifier is removed.
The util/vfio-helpers.c code (the sole user of RAMBlockNotifier) is fine
with this asymmetry because it does not rely on RAMBlockNotifier for
cleanup. It walks its internal list of DMA mappings and unmaps them by
itself.
Future users of RAMBlockNotifier may not have an internal data structure
that records added RAMBlocks so they will need ->ram_block_removed()
callbacks.
This patch makes ram_block_notifier_remove() symmetric with respect to
callbacks. Now util/vfio-helpers.c needs to unmap remaining DMA mappings
after ram_block_notifier_remove() has been called. This is necessary
since users like block/nvme.c may create additional DMA mappings that do
not originate from the RAMBlockNotifier.
Reviewed-by: David Hildenbrand <david@redhat.com> Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 20221013185908.1297568-4-stefanha@redhat.com Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Stefan Hajnoczi [Thu, 13 Oct 2022 18:58:57 +0000 (14:58 -0400)]
blkio: add libblkio block driver
libblkio (https://gitlab.com/libblkio/libblkio/) is a library for
high-performance disk I/O. It currently supports io_uring,
virtio-blk-vhost-user, and virtio-blk-vhost-vdpa with additional drivers
under development.
One of the reasons for developing libblkio is that other applications
besides QEMU can use it. This will be particularly useful for
virtio-blk-vhost-user which applications may wish to use for connecting
to qemu-storage-daemon.
libblkio also gives us an opportunity to develop in Rust behind a C API
that is easy to consume from QEMU.
This commit adds io_uring, nvme-io_uring, virtio-blk-vhost-user, and
virtio-blk-vhost-vdpa BlockDrivers to QEMU using libblkio. It will be
easy to add other libblkio drivers since they will share the majority of
code.
For now I/O buffers are copied through bounce buffers if the libblkio
driver requires it. Later commits add an optimization for
pre-registering guest RAM to avoid bounce buffers.
Stefan Hajnoczi [Thu, 13 Oct 2022 18:58:56 +0000 (14:58 -0400)]
coroutine: add flag to re-queue at front of CoQueue
When a coroutine wakes up it may determine that it must re-queue.
Normally coroutines are pushed onto the back of the CoQueue, but for
fairness it may be necessary to push it onto the front of the CoQueue.
Add a flag to specify that the coroutine should be pushed onto the front
of the CoQueue. A later patch will use this to ensure fairness in the
bounce buffer CoQueue used by the blkio BlockDriver.
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 20221013185908.1297568-2-stefanha@redhat.com Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Bjørn Forsman [Thu, 20 Oct 2022 22:03:46 +0000 (00:03 +0200)]
qga: add channel path to error messages
It's useful to know which device was used if/when it fails.
channel-win32.c had this since 2015, with c69403fcd4a0cb89f838a212ab71e4a1a3464c95 ("qemu-ga: debug printouts to
help troubleshoot installation"), this brings channel-posix.c up to
speed.
Signed-off-by: Bjørn Forsman <bjorn.forsman@gmail.com> Reviewed-by: Konstantin Kostiuk <kkostiuk@redhat.com> Signed-off-by: Konstantin Kostiuk <kkostiuk@redhat.com>
Alexander Ivanov [Mon, 17 Oct 2022 07:28:24 +0000 (09:28 +0200)]
qga: Move HW address getting to a separate function
In the next patch FreeBSD support for guest-network-get-interfaces will be
added. Previously move Linux-specific code of HW address getting to a
separate functions and add a dumb function to commands-bsd.c.
Reviewed-by: Konstantin Kostiuk <kkostiuk@redhat.com> Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com> Signed-off-by: Alexander Ivanov <alexander.ivanov@virtuozzo.com> Signed-off-by: Konstantin Kostiuk <kkostiuk@redhat.com>
Alexander Ivanov [Mon, 17 Oct 2022 07:28:23 +0000 (09:28 +0200)]
qga: Add support for user password setting in FreeBSD
Move qmp_guest_set_user_password() from __linux__ condition to
(__linux__ || __FreeBSD__) condition. Add command and arguments
for password setting in FreeBSD.
Reviewed-by: Konstantin Kostiuk <kkostiuk@redhat.com> Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com> Signed-off-by: Alexander Ivanov <alexander.ivanov@virtuozzo.com> Signed-off-by: Konstantin Kostiuk <kkostiuk@redhat.com>
* tag 'dump-pull-request' of https://gitlab.com/marcandre.lureau/qemu:
dump/win_dump: limit number of processed PRCBs
s390x: pv: Add dump support
s390x: Add KVM PV dump interface
include/elf.h: add s390x note types
s390x: Introduce PV query interface
s390x: Add protected dump cap
dump: Add architecture section and section string table support
dump: Reintroduce memory_offset and section_offset
dump: Reorder struct DumpState
dump: Write ELF section headers right after ELF header
dump: Use a buffer for ELF section data and headers
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Stefan Hajnoczi [Wed, 26 Oct 2022 14:53:41 +0000 (10:53 -0400)]
Merge tag 'pull-tcg-20221026' of https://gitlab.com/rth7680/qemu into staging
Revert incorrect cflags initialization.
Add direct jumps for tcg/loongarch64.
Speed up breakpoint check.
Improve assertions for atomic.h.
Move restore_state_to_opc to TCGCPUOps.
Cleanups to TranslationBlock maintenance.
* tag 'pull-tcg-20221026' of https://gitlab.com/rth7680/qemu: (47 commits)
accel/tcg: Remove restore_state_to_opc function
target/xtensa: Convert to tcg_ops restore_state_to_opc
target/tricore: Convert to tcg_ops restore_state_to_opc
target/sparc: Convert to tcg_ops restore_state_to_opc
target/sh4: Convert to tcg_ops restore_state_to_opc
target/s390x: Convert to tcg_ops restore_state_to_opc
target/rx: Convert to tcg_ops restore_state_to_opc
target/riscv: Convert to tcg_ops restore_state_to_opc
target/ppc: Convert to tcg_ops restore_state_to_opc
target/openrisc: Convert to tcg_ops restore_state_to_opc
target/nios2: Convert to tcg_ops restore_state_to_opc
target/mips: Convert to tcg_ops restore_state_to_opc
target/microblaze: Convert to tcg_ops restore_state_to_opc
target/m68k: Convert to tcg_ops restore_state_to_opc
target/loongarch: Convert to tcg_ops restore_state_to_opc
target/i386: Convert to tcg_ops restore_state_to_opc
target/hppa: Convert to tcg_ops restore_state_to_opc
target/hexagon: Convert to tcg_ops restore_state_to_opc
target/cris: Convert to tcg_ops restore_state_to_opc
target/avr: Convert to tcg_ops restore_state_to_opc
...
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Stefan Hajnoczi [Wed, 26 Oct 2022 14:04:05 +0000 (10:04 -0400)]
Merge tag 'pull-aspeed-20221025' of https://github.com/legoater/qemu into staging
aspeed queue :
* Performance improvement with Object class caching
* Serial Flash Discovery Parameters support for m25p80 device
* Various small adjustments on intructions and models
# -----BEGIN PGP SIGNATURE-----
#
# iQIzBAABCAAdFiEEoPZlSPBIlev+awtgUaNDx8/77KEFAmNX/WEACgkQUaNDx8/7
# 7KFhERAAhrcLcv15ny8RwatHPjzU00ZPQ0PcxGj1VDT66pCVh6M+rIeRPB2scOey
# Pu8jUvIYJ8w7ozjAP6YTQ1MP/WufniVi91Bx+vs/okSiWZa4dP0/G7NQWoc1at0s
# NBlkg57l1GMEeQb5x8vC1DizTQ1Z8Q8J/Ur3uXukXCmYVJAwHYpl/Foob1IPFgh8
# UcJ55LyuRq99lS8ib6HvRftAsC3DOcA/sl3b/TYR2+iKyi1VS2aZoQzxVCavSBcz
# PoTonT9O4OvIQthAgXRwpylW/aMYU3I7FeyOMKlCNLbmJ8LpVbX2v0KN3WBvWBv4
# OWP0DiqPUuoWFHLUGKbiVOgWQrTQXZyoD70SD/ObE1oMTLmeBoD1oFizQDvokHAR
# g2+gMdWnuWcbyaofY7YwuI6qz22gbrgh8JqX6sEWRDnY7HgCUvPhCsmci+bdN5cf
# dGcE8YKi7aD5gzoU9LRziPlhbwaEsgYLpYS7aGfNcmypgeq6lmNG7xKyw911zCTY
# uqDZWOUJy0tUIUTxoz3o1/KtsTFugjuZ+9W1SxELptJR37iwlP1vumf6bduwcx/3
# ba8tzNoXecXO5Icmq5P3lMNVM/abpkDDKS66HA87mABLEd/eCD0ojR9Kfxo0mD74
# kmQK3MFfJPkTu0ddu1cWhCIgTO7EuLuZL7gzj1oxoeXiU3YcVh8=
# =u7pS
# -----END PGP SIGNATURE-----
# gpg: Signature made Tue 25 Oct 2022 11:14:41 EDT
# gpg: using RSA key A0F66548F04895EBFE6B0B6051A343C7CFFBECA1
# gpg: Good signature from "Cédric Le Goater <clg@kaod.org>" [unknown]
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: A0F6 6548 F048 95EB FE6B 0B60 51A3 43C7 CFFB ECA1
* tag 'pull-aspeed-20221025' of https://github.com/legoater/qemu:
arm/aspeed: Replace mx25l25635e chip model
m25p80: Add the w25q01jvq SFPD table
m25p80: Add the w25q512jv SFPD table
m25p80: Add the w25q256 SFPD table
m25p80: Add the mx66l1g45g SFDP table
m25p80: Add the mx25l25635f SFPD table
m25p80: Add the mx25l25635e SFPD table
m25p80: Add erase size for mx25l25635e
m25p80: Add the n25q256a SFDP table
m25p80: Add basic support for the SFDP command
hw/arm/aspeed: increase Bletchley memory size
ast2600: Drop NEON from the CPU features
aspeed/smc: Cache AspeedSMCClass
ssi: cache SSIPeripheralClass to avoid GET_CLASS()
tests/avocado/machine_aspeed.py: Fix typos on buildroot
hw/i2c/aspeed: Fix old reg slave receive
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Michal Privoznik [Wed, 26 Oct 2022 07:30:24 +0000 (09:30 +0200)]
seccomp: Get actual errno value from failed seccomp functions
Upon failure, a libseccomp API returns actual errno value very
rarely. Fortunately, after its commit 34bf78ab (contained in
2.5.0 release), the SCMP_FLTATR_API_SYSRAWRC attribute can be set
which makes subsequent APIs return true errno on failure.
This is especially critical when seccomp_load() fails, because
generic -ECANCELED says nothing.
Signed-off-by: Michal Privoznik <mprivozn@redhat.com> Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org> Signed-off-by: Daniel P. Berrangé <berrange@redhat.com>
Bin Meng [Thu, 6 Oct 2022 15:19:25 +0000 (23:19 +0800)]
io/channel-watch: Fix socket watch on Windows
Random failure was observed when running qtests on Windows due to
"Broken pipe" detected by qmp_fd_receive(). What happened is that
the qtest executable sends testing data over a socket to the QEMU
under test but no response is received. The errno of the recv()
call from the qtest executable indicates ETIMEOUT, due to the qmp
chardev's tcp_chr_read() is never called to receive testing data
hence no response is sent to the other side.
tcp_chr_read() is registered as the callback of the socket watch
GSource. The reason of the callback not being called by glib, is
that the source check fails to indicate the source is ready. There
are two socket watch sources created to monitor the same socket
event object from the char-socket backend in update_ioc_handlers().
During the source check phase, qio_channel_socket_source_check()
calls WSAEnumNetworkEvents() to discover occurrences of network
events for the indicated socket, clear internal network event records,
and reset the event object. Testing shows that if we don't reset the
event object by not passing the event handle to WSAEnumNetworkEvents()
the symptom goes away and qtest runs very stably.
It seems we don't need to call WSAEnumNetworkEvents() at all, as we
don't parse the result of WSANETWORKEVENTS returned from this API.
We use select() to poll the socket status. Fix this instability by
dropping the WSAEnumNetworkEvents() call.
Some side notes:
During the testing, I removed the following codes in update_ioc_handlers():
And if I moved the above codes to the beginning, before the call to
io_add_watch_poll(), the symptom also goes away.
It seems two sources watching on the same socket event object is
the key that leads to the instability. The order of adding a source
watch seems to also play a role but I can't explain why.
Hopefully a Windows and glib expert could explain this behavior.
Signed-off-by: Bin Meng <bin.meng@windriver.com> Signed-off-by: Daniel P. Berrangé <berrange@redhat.com>
Bin Meng [Thu, 6 Oct 2022 15:19:23 +0000 (23:19 +0800)]
io/channel-watch: Drop a superfluous '#ifdef WIN32'
In the win32 version qio_channel_create_socket_watch() body there is
no need to do a '#ifdef WIN32'.
Signed-off-by: Bin Meng <bin.meng@windriver.com> Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com> Signed-off-by: Daniel P. Berrangé <berrange@redhat.com>
Bin Meng [Tue, 27 Sep 2022 11:05:42 +0000 (19:05 +0800)]
util/qemu-sockets: Use g_get_tmp_dir() to get the directory for temporary files
Replace the existing logic to get the directory for temporary files
with g_get_tmp_dir(), which works for win32 too.
Signed-off-by: Bin Meng <bin.meng@windriver.com> Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com> Signed-off-by: Daniel P. Berrangé <berrange@redhat.com>
Jungmin Park [Wed, 24 Aug 2022 12:37:06 +0000 (21:37 +0900)]
crypto/luks: Support creating LUKS image on Darwin
When the user creates a LUKS-encrypted qcow2 image using the qemu-img
program, the passphrase is hashed using PBKDF2 with a dynamic
number of iterations. The number of iterations is determined by
measuring thread cpu time usage, such that it takes approximately
2 seconds to compute the hash.
Because Darwin doesn't implement getrusage(RUSAGE_THREAD), we get an
error message:
> qemu-img: test.qcow2: Unable to calculate thread CPU usage on this platform
for this command:
> qemu-img create --object secret,id=key,data=1234 -f qcow2 -o 'encrypt.format=luks,encrypt.key-secret=key' test.qcow2 100M
This patch implements qcrypto_pbkdf2_get_thread_cpu() for Darwin so that
the above command works.
Signed-off-by: Jungmin Park <pjm0616@gmail.com> Signed-off-by: Daniel P. Berrangé <berrange@redhat.com>
Viktor Prutyanov [Wed, 19 Oct 2022 23:59:48 +0000 (02:59 +0300)]
dump/win_dump: limit number of processed PRCBs
When number of CPUs utilized by guest Windows is less than defined in
QEMU (i.e., desktop versions of Windows severely limits number of CPU
sockets), patch_and_save_context routine accesses non-existent PRCB and
fails. So, limit number of processed PRCBs by NumberProcessors taken
from guest Windows driver.
Signed-off-by: Viktor Prutyanov <viktor.prutyanov@redhat.com> Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-Id: <20221019235948.656411-1-viktor.prutyanov@redhat.com>
Janosch Frank [Mon, 17 Oct 2022 08:38:22 +0000 (08:38 +0000)]
s390x: pv: Add dump support
Sometimes dumping a guest from the outside is the only way to get the
data that is needed. This can be the case if a dumping mechanism like
KDUMP hasn't been configured or data needs to be fetched at a specific
point. Dumping a protected guest from the outside without help from
fw/hw doesn't yield sufficient data to be useful. Hence we now
introduce PV dump support.
The PV dump support works by integrating the firmware into the dump
process. New Ultravisor calls are used to initiate the dump process,
dump cpu data, dump memory state and lastly complete the dump process.
The UV calls are exposed by KVM via the new KVM_PV_DUMP command and
its subcommands. The guest's data is fully encrypted and can only be
decrypted by the entity that owns the customer communication key for
the dumped guest. Also dumping needs to be allowed via a flag in the
SE header.
On the QEMU side of things we store the PV dump data in the newly
introduced architecture ELF sections (storage state and completion
data) and the cpu notes (for cpu dump data).
Users can use the zgetdump tool to convert the encrypted QEMU dump to an
unencrypted one.
Signed-off-by: Janosch Frank <frankja@linux.ibm.com> Reviewed-by: Steffen Eiden <seiden@linux.ibm.com>
Message-Id: <20221017083822.43118-11-frankja@linux.ibm.com>
Janosch Frank [Mon, 17 Oct 2022 08:38:20 +0000 (08:38 +0000)]
include/elf.h: add s390x note types
Adding two s390x note types
Signed-off-by: Janosch Frank <frankja@linux.ibm.com> Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20221017083822.43118-9-frankja@linux.ibm.com>
Add a tcg_ops hook to replace the restore_state_to_opc
function call. Because these generic hooks cannot depend
on target-specific types, temporarily, copy the current
target_ulong data[] into uint64_t d64[].
Reviewed-by: Claudio Fontana <cfontana@suse.de> Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Since the only user, Arm MTE, always requires allocation,
merge the get and alloc functions to always produce a
non-null result. Also assume that the user has already
checked page validity.
Reviewed-by: Alex Bennée <alex.bennee@linaro.org> Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
accel/tcg: Call tb_invalidate_phys_page for PAGE_RESET
When PAGE_RESET is set, we are replacing pages with new
content, which means that we need to invalidate existing
cached data, such as TranslationBlocks. Perform the
reset invalidate while we're doing other invalidates,
which allows us to remove the separate invalidates from
the user-only mmap/munmap/mprotect routines.
In addition, restrict invalidation to PAGE_EXEC pages.
Since cdf713085131, we have validated PAGE_EXEC is present
before translation, which means we can assume that if the
bit is not present, there are no translations to invalidate.
Reviewed-by: Alex Bennée <alex.bennee@linaro.org> Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
accel/tcg: Remove duplicate store to tb->page_addr[]
When we added the fast path, we initialized page_addr[] early.
These stores in and around tb_page_add() are redundant; remove them.
Fixes: 50627f1b7b1 ("accel/tcg: Add fast path for translator_ld*") Reviewed-by: Alex Bennée <alex.bennee@linaro.org> Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
accel/tcg: Drop cpu_get_tb_cpu_state from TARGET_HAS_PRECISE_SMC
The results of the calls to cpu_get_tb_cpu_state,
current_{pc,cs_base,flags}, are not used.
In tb_invalidate_phys_page, use bool for current_tb_modified.
Reviewed-by: Alex Bennée <alex.bennee@linaro.org> Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
accel/tcg: Make page_alloc_target_data allocation constant
Use a constant target data allocation size for all pages.
This will be necessary to reduce overhead of page tracking.
Since TARGET_PAGE_DATA_SIZE is now required, we can use this
to omit data tracking for targets that don't require it.
Reviewed-by: Alex Bennée <alex.bennee@linaro.org> Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Change from QEMU_BUILD_BUG_ON, which requires ifdefs to avoid
problematic code, to qemu_build_assert, which can use C ifs.
Acked-by: Paolo Bonzini <pbonzini@redhat.com> Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org> Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
This differs from assert, in that with optimization enabled it
triggers at build-time. It differs from QEMU_BUILD_BUG_ON,
aka _Static_assert, in that it is sensitive to control flow
and is subject to dead-code elimination.
Acked-by: Paolo Bonzini <pbonzini@redhat.com> Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org> Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Leandro Lupori [Tue, 25 Oct 2022 20:24:22 +0000 (17:24 -0300)]
accel/tcg: Add a quicker check for breakpoints
Profiling QEMU during Fedora 35 for PPC64 boot revealed that a
considerable amount of time was being spent in
check_for_breakpoints() (0.61% of total time on PPC64 and 2.19% on
amd64), even though it was just checking that its queue was empty
and returning, when no breakpoints were set. It turns out this
function is not inlined by the compiler and it's always called by
helper_lookup_tb_ptr(), one of the most called functions.
By leaving only the check for empty queue in
check_for_breakpoints() and moving the remaining code to
check_for_breakpoints_slow(), called only when the queue is not
empty, it's possible to avoid the call overhead. An improvement of
about 3% in total time was measured on POWER9.
Signed-off-by: Leandro Lupori <leandro.lupori@eldorado.org.br> Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20221025202424.195984-2-leandro.lupori@eldorado.org.br> Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
* tag 'linux-user-for-7.2-pull-request' of https://gitlab.com/laurent_vivier/qemu:
linux-user: Add guest memory layout to exception dump
linux-user: Implement faccessat2
linux-user: remove conditionals for many fs.h ioctls
linux-user: add more compat ioctl definitions
linux-user: don't use AT_EXECFD in do_openat()
linux-user: handle /proc/self/exe with execve() syscall
linux-user: fix pidfd_send_signal()
linux-user: Fix more MIPS n32 syscall ABI issues
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Qi Hu [Mon, 17 Oct 2022 02:08:26 +0000 (10:08 +0800)]
tcg/aarch64: Remove unused code in tcg_out_op
AArch64 defines the TCG_TARGET_HAS_direct_jump. So the "else" block is
useless in the case of "INDEX_op_goto_tb" in function "tcg_out_op". Add
an assertion and delete these codes for clarity.
Suggested-by: WANG Xuerui <git@xen0n.name> Signed-off-by: Qi Hu <huqi@loongson.cn> Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org> Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20221017020826.990729-1-huqi@loongson.cn> Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Qi Hu [Sat, 15 Oct 2022 09:27:54 +0000 (17:27 +0800)]
tcg/loongarch64: Add direct jump support
Similar to the ARM64, LoongArch has PC-relative instructions such as
PCADDU18I. These instructions can be used to support direct jump for
LoongArch. Additionally, if instruction "B offset" can cover the target
address(target is within ±128MB range), a single "B offset" plus a nop
will be used by "tb_target_set_jump_target".
Signed-off-by: Qi Hu <huqi@loongson.cn> Reviewed-by: Richard Henderson <richard.henderson@linaro.org> Reviewed-by: WANG Xuerui <git@xen0n.name>
Message-Id: <20221015092754.91971-1-huqi@loongson.cn> Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Peter Maydell [Fri, 21 Oct 2022 16:34:09 +0000 (17:34 +0100)]
Revert "accel/tcg: Init TCG cflags in vCPU thread handler"
Commit a82fd5a4ec24d was intended to be a code cleanup, but
unfortunately it has a bug. It moves the initialization of the
TCG cflags from the "start a new vcpu" function to the
thread handler; this is fine when each vcpu has its own thread,
but when we are doing round-robin of vcpus on a single thread
we end up only initializing the cflags for CPU 0, not for any
of the others.
The most obvious effect of this bug is that running in icount
mode with more than one CPU is broken; typically the guest
hangs shortly after it brings up the secondary CPUs.
Cc: qemu-stable@nongnu.org Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org> Reviewed-by: Richard Henderson <richard.henderson@linaro.org> Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-Id: <20221021163409.3674911-1-peter.maydell@linaro.org> Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Helge Deller [Mon, 24 Oct 2022 20:18:09 +0000 (22:18 +0200)]
linux-user: Add guest memory layout to exception dump
When the emulation stops with a hard exception it's very useful for
debugging purposes to dump the current guest memory layout (for an
example see /proc/self/maps) beside the CPU registers.
The open_self_maps() function provides such a memory dump, but since
it's located in the syscall.c file, various changes (add #includes, make
this function externally visible, ...) are needed to be able to call it
from the existing EXCP_DUMP() macro.
This patch takes another approach by re-defining EXCP_DUMP() to call
target_exception_dump(), which is in syscall.c, consolidates the log
print functions and allows to add the call to dump the memory layout.
Beside a reduced code footprint, this approach keeps the changes across
the various callers minimal, and keeps EXCP_DUMP() highlighted as
important macro/function.
Signed-off-by: Helge Deller <deller@gmx.de> Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <Y1bzAWbw07WBKPxw@p100>
[lv: remove pc declaration and setting] Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Janosch Frank [Mon, 17 Oct 2022 08:38:16 +0000 (08:38 +0000)]
dump: Reintroduce memory_offset and section_offset
section_offset will later be used to store the offset to the section
data which will be stored last. For now memory_offset is only needed
to make section_offset look nicer.
Signed-off-by: Janosch Frank <frankja@linux.ibm.com> Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-Id: <20221017083822.43118-5-frankja@linux.ibm.com>
Janosch Frank [Mon, 17 Oct 2022 08:38:14 +0000 (08:38 +0000)]
dump: Write ELF section headers right after ELF header
Let's start bundling the writes of the headers and of the data so we
have a clear ordering between them. Since the ELF header uses offsets
to the headers we can freely order them.
Signed-off-by: Janosch Frank <frankja@linux.ibm.com> Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-Id: <20221017083822.43118-3-frankja@linux.ibm.com>
Janosch Frank [Mon, 17 Oct 2022 08:38:13 +0000 (08:38 +0000)]
dump: Use a buffer for ELF section data and headers
Currently we're writing the NULL section header if we overflow the
physical header number in the ELF header. But in the future we'll add
custom section headers AND section data.
To facilitate this we need to rearange section handling a bit. As with
the other ELF headers we split the code into a prepare and a write
step.
Signed-off-by: Janosch Frank <frankja@linux.ibm.com> Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-Id: <20221017083822.43118-2-frankja@linux.ibm.com>
Stefan Hajnoczi [Mon, 24 Oct 2022 18:27:12 +0000 (14:27 -0400)]
Merge tag 'pull-9p-20221024' of https://github.com/cschoenebeck/qemu into staging
9pfs: performance, Windows host prep, tests restructure
* Highlight of this PR is Linus Heckemann's GHashTable patch which
brings massive general performance improvements of 9p server
somewhere between factor 6 .. 12.
* Bin Meng's g_mkdir patch is a preparatory patch for upcoming
Windows host support of 9p server.
* The rest of the patches in this PR are 9p test code restructuring
and refactoring changes to improve readability and to ease
maintenance of 9p test code on the long-term.
# -----BEGIN PGP SIGNATURE-----
#
# iQJLBAABCgA1FiEEltjREM96+AhPiFkBNMK1h2Wkc5UFAmNWbs8XHHFlbXVfb3Nz
# QGNydWRlYnl0ZS5jb20ACgkQNMK1h2Wkc5V4cw/8CqoSJqoJixlP8kAGDYWq3CgF
# SKd09rIzLSWyyufAoZr1TqLwRrvEQRlZJSpL4fGvRpQLv0IQCu4x59ohHRob25Tm
# Fe7IxYBNuBwLW4yu+Y7FaujeGoYAi9Qw5q4ijq3/aSSiIeuXySKB2JmW71CQ+Tbe
# uwivsnMtWzQ7qsNwrtXYbxDs7UGkdsiW2sEQUS26GMApAXZoB+38hwtTW2Y9MOrC
# 58JuZza/fUVPzo0V1D0ggRawb5O2VTF5fz8aGFG4FvoyIW6DDZFSfnyre9QxivOl
# 5McWwSQ/D04vdEK9ornGPYr9YRGuP8g07p1EW9OfKeie4I41e9pS3UminK5lVCgo
# SfBHzz96efM5XR+Wnl4yVKowivmTqjwUU8lDqW2eB/7YBRuYUzrpxYe//UPv4q1J
# zaQV3pgwFAVkVJCnkcLCa1JQbH581bXSsuRlDdYqoRYfyzXoxbywNjvn9BXE0PrG
# WRecS//GyN3GVZYxMwb3H052110pYsYIg2YZ2H4QiqCwpEHHvy+L/ZXm19vbDm7B
# GYJQPUK8/y0NGwZsUYcUSx1TWlU9ZPwrbqZfv7e7+B6FL4VNjdaqb8PvS9admWSq
# LOSzrVVIus+nb7tP99d1Fb6oRyCy3x8E48gTr5UtTJHC4SAw/OBJmem6GOc/D490
# H7Dq8Y27qsQ6fT7iPm8=
# =MxSG
# -----END PGP SIGNATURE-----
# gpg: Signature made Mon 24 Oct 2022 06:54:07 EDT
# gpg: using RSA key 96D8D110CF7AF8084F88590134C2B58765A47395
# gpg: issuer "qemu_oss@crudebyte.com"
# gpg: Good signature from "Christian Schoenebeck <qemu_oss@crudebyte.com>" [unknown]
# gpg: WARNING: The key's User ID is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: ECAB 1A45 4014 1413 BA38 4926 30DB 47C3 A012 D5F4
# Subkey fingerprint: 96D8 D110 CF7A F808 4F88 5901 34C2 B587 65A4 7395
* tag 'pull-9p-20221024' of https://github.com/cschoenebeck/qemu: (23 commits)
tests/9p: remove unnecessary g_strdup() calls
tests/9p: merge v9fs_tunlinkat() and do_unlinkat()
tests/9p: merge v9fs_tlink() and do_hardlink()
tests/9p: merge v9fs_tsymlink() and do_symlink()
tests/9p: merge v9fs_tlcreate() and do_lcreate()
tests/9p: merge v9fs_tmkdir() and do_mkdir()
tests/9p: convert v9fs_tflush() to declarative arguments
tests/9p: simplify callers of twrite()
tests/9p: convert v9fs_twrite() to declarative arguments
tests/9p: simplify callers of tlopen()
tests/9p: convert v9fs_tlopen() to declarative arguments
tests/9p: simplify callers of treaddir()
tests/9p: convert v9fs_treaddir() to declarative arguments
tests/9p: simplify callers of tgetattr()
tests/9p: convert v9fs_tgetattr() to declarative arguments
tests/9p: simplify callers of tattach()
tests/9p: merge v9fs_tattach(), do_attach(), do_attach_rqid()
tests/9p: merge v9fs_tversion() and do_version()
tests/9p: simplify callers of twalk()
tests/9p: merge *walk*() functions
...
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
* tag 'for-upstream' of https://gitlab.com/bonzini/qemu:
target/i386: implement FMA instructions
target/i386: implement F16C instructions
target/i386: introduce function to set rounding mode from FPCW or MXCSR bits
target/i386: decode-new: avoid out-of-bounds access to xmm_regs[-1]
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
* tag 'm68k-for-7.2-pull-request' of https://github.com/vivier/qemu-m68k:
m68k: write bootinfo as rom section and re-randomize on reboot
m68k: rework BI_VIRT_RNG_SEED as BI_RNG_SEED
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Volker Rümelin [Sat, 22 Oct 2022 14:12:04 +0000 (16:12 +0200)]
ui: remove useless typecasts
Commit 8f9abdf586 ("chardev: src buffer const for write functions")
changed the type of the second parameter of qemu_chr_be_write()
from uint8_t * to const uint8_t *. Remove the now useless type
casts from qemu_chr_be_write() function calls in ui/console.c and
ui/gtk.c.
Julia Suvorova [Sun, 23 Oct 2022 19:58:12 +0000 (21:58 +0200)]
hw/mem/nvdimm: fix error message for 'unarmed' flag
In the ACPI specification [1], the 'unarmed' bit is set when a device
cannot accept a persistent write. This means that when a memdev is
read-only, the 'unarmed' flag must be turned on. The logic is correct,
just changing the error message.
[1] ACPI NFIT NVDIMM Region Mapping Structure "NVDIMM State Flags" Bit 3
Fixes: dbd730e859 ("nvdimm: check -object memory-backend-file, readonly=on option") Signed-off-by: Julia Suvorova <jusual@redhat.com> Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com> Reviewed-by: Pankaj Gupta <pankaj.gupta@amd.com> Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org> Acked-by: David Hildenbrand <david@redhat.com>
Message-Id: <20221023195812.15523-1-jusual@redhat.com> Signed-off-by: David Hildenbrand <david@redhat.com>
projects / qemu.git / log