From 2435d79033f5e7400195ed3b31585c0c053de553 Mon Sep 17 00:00:00 2001 From: Poovendhan Selvaraj Date: Wed, 31 May 2023 08:56:48 +0530 Subject: [PATCH] arm64: dts: qcom: ipq9574: add support for RDP454 variant Add the initial device tree support for the Reference Design Platform (RDP) 454 based on IPQ9574 family of SoCs. This patch adds support for Console UART, SPI NOR and SMPA1 regulator node. Signed-off-by: Poovendhan Selvaraj Signed-off-by: Bjorn Andersson Link: https://lore.kernel.org/r/20230531032648.23816-3-quic_poovendh@quicinc.com --- arch/arm64/boot/dts/qcom/Makefile | 1 + arch/arm64/boot/dts/qcom/ipq9574-rdp454.dts | 80 +++++++++++++++++++++ 2 files changed, 81 insertions(+) create mode 100644 arch/arm64/boot/dts/qcom/ipq9574-rdp454.dts diff --git a/arch/arm64/boot/dts/qcom/Makefile b/arch/arm64/boot/dts/qcom/Makefile index c1573bba67292..337abc4ceb177 100644 --- a/arch/arm64/boot/dts/qcom/Makefile +++ b/arch/arm64/boot/dts/qcom/Makefile @@ -16,6 +16,7 @@ dtb-$(CONFIG_ARCH_QCOM) += ipq9574-rdp418.dtb dtb-$(CONFIG_ARCH_QCOM) += ipq9574-rdp433.dtb dtb-$(CONFIG_ARCH_QCOM) += ipq9574-rdp449.dtb dtb-$(CONFIG_ARCH_QCOM) += ipq9574-rdp453.dtb +dtb-$(CONFIG_ARCH_QCOM) += ipq9574-rdp454.dtb dtb-$(CONFIG_ARCH_QCOM) += msm8916-acer-a1-724.dtb dtb-$(CONFIG_ARCH_QCOM) += msm8916-alcatel-idol347.dtb dtb-$(CONFIG_ARCH_QCOM) += msm8916-asus-z00l.dtb diff --git a/arch/arm64/boot/dts/qcom/ipq9574-rdp454.dts b/arch/arm64/boot/dts/qcom/ipq9574-rdp454.dts new file mode 100644 index 0000000000000..6efae3426cb84 --- /dev/null +++ b/arch/arm64/boot/dts/qcom/ipq9574-rdp454.dts @@ -0,0 +1,80 @@ +// SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause) +/* + * IPQ9574 RDP454 board device tree source + * + * Copyright (c) 2020-2021 The Linux Foundation. All rights reserved. + * Copyright (c) 2022-2023 Qualcomm Innovation Center, Inc. All rights reserved. + */ + +/dts-v1/; + +#include "ipq9574.dtsi" + +/ { + model = "Qualcomm Technologies, Inc. IPQ9574/AP-AL02-C9"; + compatible = "qcom,ipq9574-ap-al02-c9", "qcom,ipq9574"; + + aliases { + serial0 = &blsp1_uart2; + }; + + chosen { + stdout-path = "serial0:115200n8"; + }; +}; + +&blsp1_spi0 { + pinctrl-0 = <&spi_0_pins>; + pinctrl-names = "default"; + status = "okay"; + + flash@0 { + compatible = "micron,n25q128a11", "jedec,spi-nor"; + reg = <0>; + #address-cells = <1>; + #size-cells = <1>; + spi-max-frequency = <50000000>; + }; +}; + +&blsp1_uart2 { + pinctrl-0 = <&uart2_pins>; + pinctrl-names = "default"; + status = "okay"; +}; + +&rpm_requests { + regulators { + compatible = "qcom,rpm-mp5496-regulators"; + + ipq9574_s1: s1 { + /* + * During kernel bootup, the SoC runs at 800MHz with 875mV set by the bootloaders. + * During regulator registration, kernel not knowing the initial voltage, + * considers it as zero and brings up the regulators with minimum supported voltage. + * Update the regulator-min-microvolt with SVS voltage of 725mV so that + * the regulators are brought up with 725mV which is sufficient for all the + * corner parts to operate at 800MHz + */ + regulator-min-microvolt = <725000>; + regulator-max-microvolt = <1075000>; + }; + }; +}; + +&sleep_clk { + clock-frequency = <32000>; +}; + +&tlmm { + spi_0_pins: spi-0-state { + pins = "gpio11", "gpio12", "gpio13", "gpio14"; + function = "blsp0_spi"; + drive-strength = <8>; + bias-disable; + }; +}; + +&xo_board_clk { + clock-frequency = <24000000>; +}; -- 2.30.2