From 2821c34a996b4a0991d33bead5caa84267e2dccd Mon Sep 17 00:00:00 2001 From: Jonathan Albrieux Date: Tue, 3 Oct 2023 15:18:29 +0200 Subject: [PATCH] arm64: dts: qcom: msm8916-longcheer-l8910: Add sound and modem Enable sound and modem for the Longcheer L8910 (BQ Aquaris X5). The setup is similar to most MSM8916 devices, i.e.: - QDSP6 audio - Earpiece/headphones/microphones via digital/analog codec in MSM8916/PM8916 - Audio jack detection via analog codec in PM8916 - WWAN Internet via BAM-DMUX except: - Awinic AW8738 connected to HPH_R (headphones) output of the analog codec. Note that unlike for wingtech-wt88047 there is no analog switch that would allow disabling output via the headphone jack when the speaker is enabled. Signed-off-by: Jonathan Albrieux Co-developed-by: Stephan Gerhold Signed-off-by: Stephan Gerhold Reviewed-by: Konrad Dybcio Link: https://lore.kernel.org/r/20231003-msm8916-modem-v2-11-61b684be55c0@gerhold.net Signed-off-by: Bjorn Andersson --- .../boot/dts/qcom/msm8916-longcheer-l8910.dts | 52 +++++++++++++++++++ 1 file changed, 52 insertions(+) diff --git a/arch/arm64/boot/dts/qcom/msm8916-longcheer-l8910.dts b/arch/arm64/boot/dts/qcom/msm8916-longcheer-l8910.dts index 41cadb906b98c..e64bf687ca7db 100644 --- a/arch/arm64/boot/dts/qcom/msm8916-longcheer-l8910.dts +++ b/arch/arm64/boot/dts/qcom/msm8916-longcheer-l8910.dts @@ -3,6 +3,8 @@ /dts-v1/; #include "msm8916-pm8916.dtsi" +#include "msm8916-modem-qdsp6.dtsi" + #include #include #include @@ -22,6 +24,16 @@ stdout-path = "serial0"; }; + speaker_amp: audio-amplifier { + compatible = "awinic,aw8738"; + mode-gpios = <&tlmm 114 GPIO_ACTIVE_HIGH>; + awinic,mode = <5>; + sound-name-prefix = "Speaker Amp"; + + pinctrl-0 = <&spk_ext_pa_default>; + pinctrl-names = "default"; + }; + flash-led-controller { compatible = "ocs,ocp8110"; enable-gpios = <&tlmm 49 GPIO_ACTIVE_HIGH>; @@ -107,6 +119,17 @@ status = "okay"; }; +&mpss_mem { + reg = <0x0 0x86800000 0x0 0x5000000>; +}; + +&pm8916_codec { + qcom,micbias-lvl = <2800>; + qcom,mbhc-vthreshold-low = <75 100 120 180 500>; + qcom,mbhc-vthreshold-high = <75 100 120 180 500>; + qcom,hphl-jack-type-normally-open; +}; + &pm8916_resin { status = "okay"; linux,code = ; @@ -137,6 +160,28 @@ cd-gpios = <&tlmm 38 GPIO_ACTIVE_LOW>; }; +&sound { + /* + * Provide widgets/pin-switches to allow enabling speaker separately. + * The hardware does not provide a way to disable the output via the + * headphone jack when the speaker is enabled. + */ + model = "bq-paella"; + widgets = + "Speaker", "Speaker", + "Headphone", "Headphones"; + pin-switches = "Speaker"; + audio-routing = + "Speaker", "Speaker Amp OUT", + "Speaker Amp IN", "HPH_R", + "Headphones", "HPH_L", + "Headphones", "HPH_R", + "AMIC1", "MIC BIAS External1", + "AMIC2", "MIC BIAS Internal2", + "AMIC3", "MIC BIAS External1"; + aux-devs = <&speaker_amp>; +}; + &usb { status = "okay"; extcon = <&usb_id>, <&usb_id>; @@ -205,6 +250,13 @@ bias-disable; }; + spk_ext_pa_default: spk-ext-pa-default-state { + pins = "gpio114"; + function = "gpio"; + drive-strength = <2>; + bias-disable; + }; + usb_id_default: usb-id-default-state { pins = "gpio110"; function = "gpio"; -- 2.30.2