From 8668223a1ea74624e934cb49ccde77db6f39d660 Mon Sep 17 00:00:00 2001 From: Linus Walleij Date: Tue, 26 Nov 2019 13:47:36 +0100 Subject: [PATCH] ARM: dts: ux500: Split TVK DTSI files in two The TVK1281618 was made in R1, R2 and R3 variants. The most commonly used variants are R2 and R3 so split out these to their own files. The R3 version has a totally different display than R1 and R2 and a different set of sensors. Cc: Stephan Gerhold Signed-off-by: Linus Walleij Link: https://lore.kernel.org/r/20191126124738.77690-2-linus.walleij@linaro.org --- arch/arm/boot/dts/ste-href-tvk1281618-r2.dtsi | 79 +++++++++++++++++++ arch/arm/boot/dts/ste-href-tvk1281618-r3.dtsi | 58 ++++++++++++++ arch/arm/boot/dts/ste-href-tvk1281618.dtsi | 71 +---------------- arch/arm/boot/dts/ste-hrefprev60-tvk.dts | 2 +- arch/arm/boot/dts/ste-hrefv60plus-tvk.dts | 2 +- 5 files changed, 141 insertions(+), 71 deletions(-) create mode 100644 arch/arm/boot/dts/ste-href-tvk1281618-r2.dtsi create mode 100644 arch/arm/boot/dts/ste-href-tvk1281618-r3.dtsi diff --git a/arch/arm/boot/dts/ste-href-tvk1281618-r2.dtsi b/arch/arm/boot/dts/ste-href-tvk1281618-r2.dtsi new file mode 100644 index 0000000000000..e024520f4d476 --- /dev/null +++ b/arch/arm/boot/dts/ste-href-tvk1281618-r2.dtsi @@ -0,0 +1,79 @@ +// SPDX-License-Identifier: GPL-2.0-or-later +/* + * Device Tree for the TVK1281618 R2 UIB + */ + +#include "ste-href-tvk1281618.dtsi" + +/ { + soc { + i2c@80128000 { + lsm303dlh@18 { + /* Accelerometer */ + compatible = "st,lsm303dlh-accel"; + st,drdy-int-pin = <1>; + drive-open-drain; + reg = <0x18>; + vdd-supply = <&ab8500_ldo_aux1_reg>; + vddio-supply = <&db8500_vsmps2_reg>; + pinctrl-names = "default"; + pinctrl-0 = <&accel_tvk_mode>; + /* + * These interrupts cannot be used: the other component + * ST-Micro L3D4200D gyro that is connected to the same lines + * cannot set its DRDY line to open drain, so it cannot be + * shared with other peripherals. The should be defined for + * the falling edge if they could be wired together. + * + * interrupts-extended = + * <&gpio1 0 IRQ_TYPE_EDGE_FALLING>, + * <&gpio2 19 IRQ_TYPE_EDGE_FALLING>; + */ + }; + lsm303dlh@1e { + /* Magnetometer */ + compatible = "st,lsm303dlh-magn"; + reg = <0x1e>; + vdd-supply = <&ab8500_ldo_aux1_reg>; + vddio-supply = <&db8500_vsmps2_reg>; + /* + * These interrupts cannot be used: the other component + * ST-Micro L3D4200D gyro that is connected to the same lines + * cannot set its DRDY line to open drain, so it cannot be + * shared with other peripherals. The should be defined for + * the falling edge if they could be wired together. + * + * interrupts-extended = + * <&gpio1 0 IRQ_TYPE_EDGE_FALLING>, + * <&gpio2 19 IRQ_TYPE_EDGE_FALLING>; + */ + }; + lis331dl@1c { + /* Accelerometer */ + compatible = "st,lis331dl-accel"; + st,drdy-int-pin = <1>; + reg = <0x1c>; + vdd-supply = <&ab8500_ldo_aux1_reg>; + vddio-supply = <&db8500_vsmps2_reg>; + pinctrl-names = "default"; + pinctrl-0 = <&accel_tvk_mode>; + interrupt-parent = <&gpio2>; + /* INT2 would need to be open drain */ + interrupts = <18 IRQ_TYPE_EDGE_RISING>, + <19 IRQ_TYPE_EDGE_RISING>; + }; + }; + mcde@a0350000 { + status = "okay"; + + dsi@a0351000 { + panel { + compatible = "samsung,s6d16d0"; + reg = <0>; + vdd1-supply = <&ab8500_ldo_aux1_reg>; + reset-gpios = <&gpio2 1 GPIO_ACTIVE_LOW>; + }; + }; + }; + }; +}; diff --git a/arch/arm/boot/dts/ste-href-tvk1281618-r3.dtsi b/arch/arm/boot/dts/ste-href-tvk1281618-r3.dtsi new file mode 100644 index 0000000000000..cb3677f0a1cbb --- /dev/null +++ b/arch/arm/boot/dts/ste-href-tvk1281618-r3.dtsi @@ -0,0 +1,58 @@ +// SPDX-License-Identifier: GPL-2.0-or-later +/* + * Device Tree for the TVK1281618 R2 UIB + */ + +#include "ste-href-tvk1281618.dtsi" + +/ { + soc { + i2c@80128000 { + /* Marked: + * 129 + * M35 + * L3GD20 + */ + l3gd20@6a { + /* Gyroscope */ + compatible = "st,l3gd20"; + status = "disabled"; + st,drdy-int-pin = <1>; + drive-open-drain; + reg = <0x6a>; // 0x6a or 0x6b + vdd-supply = <&ab8500_ldo_aux1_reg>; + vddio-supply = <&db8500_vsmps2_reg>; + }; + /* + * Marked: + * 2122 + * C3H + * DQEEE + * LIS3DH? + */ + lis3dh@18 { + /* Accelerometer */ + compatible = "st,lis3dh-accel"; + st,drdy-int-pin = <1>; + reg = <0x18>; + vdd-supply = <&ab8500_ldo_aux1_reg>; + vddio-supply = <&db8500_vsmps2_reg>; + pinctrl-names = "default"; + pinctrl-0 = <&accel_tvk_mode>; + }; + }; + + mcde@a0350000 { + status = "okay"; + + dsi@a0351000 { + panel { + compatible = "sony,acx424akp"; + reg = <0>; + vddi-supply = <&ab8500_ldo_aux1_reg>; + reset-gpios = <&gpio2 1 GPIO_ACTIVE_LOW>; + }; + }; + }; + }; +}; diff --git a/arch/arm/boot/dts/ste-href-tvk1281618.dtsi b/arch/arm/boot/dts/ste-href-tvk1281618.dtsi index 3bafd26b48240..e1dbfae225956 100644 --- a/arch/arm/boot/dts/ste-href-tvk1281618.dtsi +++ b/arch/arm/boot/dts/ste-href-tvk1281618.dtsi @@ -2,7 +2,7 @@ /* * Copyright 2012 ST-Ericsson AB * - * Device Tree for the TVK1281618 UIB + * Device Tree for the TVK1281618 family of UIBs */ #include @@ -81,62 +81,8 @@ }; }; }; - /* Sensors mounted on this board variant */ + /* Sensors mounted on all board variants */ i2c@80128000 { - lsm303dlh@18 { - /* Accelerometer */ - compatible = "st,lsm303dlh-accel"; - st,drdy-int-pin = <1>; - drive-open-drain; - reg = <0x18>; - vdd-supply = <&ab8500_ldo_aux1_reg>; - vddio-supply = <&db8500_vsmps2_reg>; - pinctrl-names = "default"; - pinctrl-0 = <&accel_tvk_mode>; - /* - * These interrupts cannot be used: the other component - * ST-Micro L3D4200D gyro that is connected to the same lines - * cannot set its DRDY line to open drain, so it cannot be - * shared with other peripherals. The should be defined for - * the falling edge if they could be wired together. - * - * interrupts-extended = - * <&gpio1 0 IRQ_TYPE_EDGE_FALLING>, - * <&gpio2 19 IRQ_TYPE_EDGE_FALLING>; - */ - }; - lsm303dlh@1e { - /* Magnetometer */ - compatible = "st,lsm303dlh-magn"; - reg = <0x1e>; - vdd-supply = <&ab8500_ldo_aux1_reg>; - vddio-supply = <&db8500_vsmps2_reg>; - /* - * These interrupts cannot be used: the other component - * ST-Micro L3D4200D gyro that is connected to the same lines - * cannot set its DRDY line to open drain, so it cannot be - * shared with other peripherals. The should be defined for - * the falling edge if they could be wired together. - * - * interrupts-extended = - * <&gpio1 0 IRQ_TYPE_EDGE_FALLING>, - * <&gpio2 19 IRQ_TYPE_EDGE_FALLING>; - */ - }; - lis331dl@1c { - /* Accelerometer */ - compatible = "st,lis331dl-accel"; - st,drdy-int-pin = <1>; - reg = <0x1c>; - vdd-supply = <&ab8500_ldo_aux1_reg>; - vddio-supply = <&db8500_vsmps2_reg>; - pinctrl-names = "default"; - pinctrl-0 = <&accel_tvk_mode>; - interrupt-parent = <&gpio2>; - /* INT2 would need to be open drain */ - interrupts = <18 IRQ_TYPE_EDGE_RISING>, - <19 IRQ_TYPE_EDGE_RISING>; - }; ak8974@f { /* Magnetometer */ compatible = "asahi-kasei,ak8974"; @@ -268,18 +214,5 @@ }; }; }; - - mcde@a0350000 { - status = "okay"; - - dsi@a0351000 { - panel { - compatible = "samsung,s6d16d0"; - reg = <0>; - vdd1-supply = <&ab8500_ldo_aux1_reg>; - reset-gpios = <&gpio2 1 GPIO_ACTIVE_LOW>; - }; - }; - }; }; }; diff --git a/arch/arm/boot/dts/ste-hrefprev60-tvk.dts b/arch/arm/boot/dts/ste-hrefprev60-tvk.dts index 8b88c91dca6c0..142f5475521f8 100644 --- a/arch/arm/boot/dts/ste-hrefprev60-tvk.dts +++ b/arch/arm/boot/dts/ste-hrefprev60-tvk.dts @@ -6,7 +6,7 @@ /dts-v1/; #include "ste-db8500.dtsi" #include "ste-hrefprev60.dtsi" -#include "ste-href-tvk1281618.dtsi" +#include "ste-href-tvk1281618-r2.dtsi" / { model = "ST-Ericsson HREF (pre-v60) and TVK1281618 UIB"; diff --git a/arch/arm/boot/dts/ste-hrefv60plus-tvk.dts b/arch/arm/boot/dts/ste-hrefv60plus-tvk.dts index b31e43d5ff899..5d4b8245f02c0 100644 --- a/arch/arm/boot/dts/ste-hrefv60plus-tvk.dts +++ b/arch/arm/boot/dts/ste-hrefv60plus-tvk.dts @@ -8,7 +8,7 @@ /dts-v1/; #include "ste-db8500.dtsi" #include "ste-hrefv60plus.dtsi" -#include "ste-href-tvk1281618.dtsi" +#include "ste-href-tvk1281618-r2.dtsi" / { model = "ST-Ericsson HREF (v60+) and TVK1281618 UIB"; -- 2.30.2