From f283745b3caffcbc69ca71b7b22a9d3c2054284f Mon Sep 17 00:00:00 2001
From: Andrew Lunn <andrew@lunn.ch>
Date: Sun, 16 Oct 2016 19:56:53 +0200
Subject: [PATCH] arm: vf610: zii devel b: Add support for switch interrupts
The Switches use GPIO lines to indicate interrupts from two of the
switches.
With these interrupts in place, we can make use of the interrupt
controllers within the switch to indicate when the internal PHYs
generate an interrupt. Use standard PHY properties to do this.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
---
arch/arm/boot/dts/vf610-zii-dev-rev-b.dts | 51 +++++++++++++++++++++++
1 file changed, 51 insertions(+)
diff --git a/arch/arm/boot/dts/vf610-zii-dev-rev-b.dts b/arch/arm/boot/dts/vf610-zii-dev-rev-b.dts
index 5c1fcab4a6f78..1552db00cc592 100644
--- a/arch/arm/boot/dts/vf610-zii-dev-rev-b.dts
+++ b/arch/arm/boot/dts/vf610-zii-dev-rev-b.dts
@@ -88,10 +88,16 @@
switch0: switch0@0 {
compatible = "marvell,mv88e6085";
+ pinctrl-0 = <&pinctrl_gpio_switch0>;
+ pinctrl-names = "default";
#address-cells = <1>;
#size-cells = <0>;
reg = <0>;
dsa,member = <0 0>;
+ interrupt-parent = <&gpio0>;
+ interrupts = <27 IRQ_TYPE_LEVEL_LOW>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
ports {
#address-cells = <1>;
@@ -99,16 +105,19 @@
port@0 {
reg = <0>;
label = "lan0";
+ phy-handle = <&switch0phy0>;
};
port@1 {
reg = <1>;
label = "lan1";
+ phy-handle = <&switch0phy1>;
};
port@2 {
reg = <2>;
label = "lan2";
+ phy-handle = <&switch0phy2>;
};
switch0port5: port@5 {
@@ -133,6 +142,24 @@
};
};
};
+ mdio {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ switch0phy0: switch0phy0@0 {
+ reg = <0>;
+ interrupt-parent = <&switch0>;
+ interrupts = <0 IRQ_TYPE_LEVEL_HIGH>;
+ };
+ switch0phy1: switch1phy0@1 {
+ reg = <1>;
+ interrupt-parent = <&switch0>;
+ interrupts = <1 IRQ_TYPE_LEVEL_HIGH>; };
+ switch0phy2: switch1phy0@2 {
+ reg = <2>;
+ interrupt-parent = <&switch0>;
+ interrupts = <2 IRQ_TYPE_LEVEL_HIGH>;
+ };
+ };
};
};
@@ -143,10 +170,16 @@
switch1: switch1@0 {
compatible = "marvell,mv88e6085";
+ pinctrl-0 = <&pinctrl_gpio_switch1>;
+ pinctrl-names = "default";
#address-cells = <1>;
#size-cells = <0>;
reg = <0>;
dsa,member = <0 1>;
+ interrupt-parent = <&gpio0>;
+ interrupts = <26 IRQ_TYPE_LEVEL_LOW>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
ports {
#address-cells = <1>;
@@ -196,12 +229,18 @@
#size-cells = <0>;
switch1phy0: switch1phy0@0 {
reg = <0>;
+ interrupt-parent = <&switch1>;
+ interrupts = <0 IRQ_TYPE_LEVEL_HIGH>;
};
switch1phy1: switch1phy0@1 {
reg = <1>;
+ interrupt-parent = <&switch1>;
+ interrupts = <1 IRQ_TYPE_LEVEL_HIGH>;
};
switch1phy2: switch1phy0@2 {
reg = <2>;
+ interrupt-parent = <&switch1>;
+ interrupts = <2 IRQ_TYPE_LEVEL_HIGH>;
};
};
};
@@ -636,6 +675,18 @@
>;
};
+ pinctrl_gpio_switch0: pinctrl-gpio-switch0 {
+ fsl,pins = <
+ VF610_PAD_PTB5__GPIO_27 0x219d
+ >;
+ };
+
+ pinctrl_gpio_switch1: pinctrl-gpio-switch1 {
+ fsl,pins = <
+ VF610_PAD_PTB4__GPIO_26 0x219d
+ >;
+ };
+
pinctrl_i2c_mux_reset: pinctrl-i2c-mux-reset {
fsl,pins = <
VF610_PAD_PTE14__GPIO_119 0x31c2
--
2.30.2